Previously a hard-coded limitation of maximum two key or message
verification checks were introduced when checking the message's
SIG(0) signature. It was done in order to protect against possible
DoS attacks. The logic behind choosing the number two was that more
than one key should only be required only during key rotations, and
in that case two keys are enough. But later it became apparent that
there are other use cases too where even more keys are required, see
issue number #5050 in GitLab.
This change introduces two new configuration options for the views,
sig0key-checks-limit and sig0message-checks-limit, which define how
many keys are allowed to be checked to find a matching key, and how
many message verifications are allowed to take place once a matching
key has been found. The latter protects against expensive cryptographic
operations when there are keys with colliding tags and algorithm
numbers, with default being 2, and the former protects against a bit
less expensive key parsing operations and defaults to 16.
Add a new big zone, run a zone transfer in slow mode, and check
whether the zone transfer gets canceled because 100000 bytes are
not transferred in 5 seconds (as it's running in slow mode).
- there are now two functions for getting rdataslab size:
dns_rdataslab_size() is for full slabs and dns_rdataslab_sizeraw()
for raw slabs. there is no longer a need for a reservelen parameter.
- dns_rdataslab_count() also no longer takes a reservelen parameter.
(currently it's never used for raw slabs, so there is no _countraw()
function.)
- dns_rdataslab_rdatasize() has been removed, because
dns_rdataslab_sizeraw() can do the same thing.
- dns_rdataslab_merge() and dns_rdataslab_subtract() both take
slabheader parameters instead of character buffers, and the
reservelen parameter has been removed.
This check in the nsupdate system test expects the opaque
representation of the "dohpath" Service Parameter Key. Use
the +svcparamkeycompat dig option to enable it.
If a deferred validation on data that was originally queried with
CD=1 fails, we now repeat the query, since the zone data may have
changed in the meantime.
In some cases, the numeric identifier doesn't correspond to the
directory name (i.e. `resolver` server in `shutdown` test, which is
supposed to be 10.53.0.3). These are typically servers that shouldn't be
auto-started by the runner, thus avoiding the typical `*ns<X>` name.
Support these server by allowing a fallback initialization with custom
numeric identifier in case it can't be parsed from the directory name.
The start()/stop() functions can be used in the pytests in the same way
as start_server and stop_server functions were used in shell tests. Note
that the servers obtained through the servers fixture are still started
and stopped by the test runner at the start and end of the test. This
makes these functions mostly useful for restarting the server(s)
mid-test.
Previously, these functions have been provided as fixtures. This was
limiting re-use, because it wasn't possible to call these outside of
tests / other fixtures without passing these utility functions around.
Move them into isctest.run package instead.
The ANS servers were not to written to handle NS queries at the
QNAME resulting in gratuitious protocol errors that will break tests
when NS requests are made for the QNAME.
In #1870, the expiration time of ANCIENT records were printed, but
actually the ancient records are very short lived, and the information
carries a little value.
Instead of printing the expiration of ANCIENT records, print the
expiration time of STALE records.
When the header has been marked as ANCIENT, but the ttl hasn't been
reset (this happens in couple of places), the rdataset TTL would be
set to the header timestamp instead to a reasonable TTL value.
Since this header has been already expired (ANCIENT is set), set the
rdataset TTL to 0 and don't reuse this field to print the expiration
time when dumping the cache. Instead of printing the time, we now
just print 'expired (awaiting cleanup'.
Named was failing to recover when spoofed nameserver address from
a signed zone for a peer zone were returned to a previous CD=1
query. Validate non-glue interior server addresses before using them.
the search for the deepest known zone cut in the cache could
improperly reject a node containing stale data, even if the
NS rdataset wasn't the data that was stale.
this change also improves the efficiency of the search by
stopping it when both NS and RRSIG(NS) have been found.
Changes !9948 introducing the support of extended DNS error code 1 and 2
uses SHA-1 digest for some tests which break FIPS platform. The digest
itself was irrelevant, another digest is used.
When EDE 3 (stale answer) was added the serve-stale tests were checking
for those exclusively, i.e. grepping for no "EDE" in the dig output when
no stale answer was expected.
However, some stale tests disable stale answers and make the
authoritative server unresponsive, effectively triggering a timed out
request thus an EDE 22. Update those tests so they still tests the
absence of EDE 3 error, but also the presence of EDE 22.
This re-do a previously existing EDE 22 system test as well as add
another one making sure the timed out flow detection works also on UDP
when the resolver is contacting the authoritative server. (the existing
test was using TCP to contact the authoritative servers).
A DNSSEC validation can fail in the case where multiple DNSKEY are
available for a zone and none of them are supported, but for different
reasons: one has a DS record in the parent zone using an unsupported
digest while the other one uses an unsupported encryption algorithm.
Add a specific test case covering this flow and making sure that two
extended DNS error are provided: code 1 and 2, each of them highlighting
unsupported algorithm and digest.
The servers are setup and torn down once per each test module. All the
logs and server state persists between individual tests within the same
module. The servers fixture representing these servers should be
module-wide as well.
When explicitly set to True, the "verify" argument lets dnspython verify
certificates used for the connection. As most certificates in the system
test will inevitably be self-signed, the "verify" argument defaults to
False.
The "verify" argument is present in dnspython since the version 2.5.0.
the isc_mem allocation functions can no longer fail; as a result,
ISC_R_NOMEMORY is now rarely used: only when an external library
such as libjson-c or libfstrm could return NULL. (even in
these cases, arguably we should assert rather than returning
ISC_R_NOMEMORY.)
code and comments that mentioned ISC_R_NOMEMORY have been
cleaned up, and the following functions have been changed to
type void, since (in most cases) the only value they could
return was ISC_R_SUCCESS:
- dns_dns64_create()
- dns_dyndb_create()
- dns_ipkeylist_resize()
- dns_kasp_create()
- dns_kasp_key_create()
- dns_keystore_create()
- dns_order_create()
- dns_order_add()
- dns_peerlist_new()
- dns_tkeyctx_create()
- dns_view_create()
- dns_zone_setorigin()
- dns_zone_setfile()
- dns_zone_setstream()
- dns_zone_getdbtype()
- dns_zone_setjournal()
- dns_zone_setkeydirectory()
- isc_lex_openstream()
- isc_portset_create()
- isc_symtab_create()
(the exception is dns_view_create(), which could have returned
other error codes in the event of a crypto library failure when
calling isc_file_sanitize(), but that should be a RUNTIME_CHECK
anyway.)
Track inside the dns_dnsseckey structure whether we have seen the
private key, or if this key only has a public key file.
If the key only has a public key file, or a DNSKEY reference in the
zone, mark the key 'pubkey'. In dnssec-signzone, if the key only
has a public key available, consider the key to be offline. Any
signatures that should be refreshed for which the key is not available,
retain the signature.
So in the code, 'expired' becomes 'refresh', and the new 'expired'
is only used to determine whether we need to keep the signature if
the corresponding key is not available (retaining the signature if
it is not expired).
In the 'keysthatsigned' function, we can remove:
- key->force_publish = false;
- key->force_sign = false;
because they are redundant ('dns_dnsseckey_create' already sets these
values to false).
Add a test case for the scenario below.
There is a case when signing a zone with dnssec-signzone where the
private key file is moved outside the key directory (for offline
ksk purposes), and then the zone is resigned. The signature of the
DNSKEY needs refreshing, but is not expired.
Rather than removing the signature without having a valid replacement,
leave the signature in the zone (despite it needs to be refreshed).
Since the read timeout now works, the resolver time outs from the
dispatch level instead of from the "hung fetch" timer, and so the
EDE value in 'fctx_expired()' is not being set. Remove the expected
EDE value from the test.
The network manager layer has two different timers with their
own timeout values for TCP connections: connect timeout and read
timeout. Separate the connect and the read TCP timeouts in the
dispatch module too.
Instead of running the whole resolver/ns4 server with -T noaa flag,
use it only for the part where it is actually needed. The -T noaa
could interfere with other parts of the test because the answers don't
have the authoritative-answer bit set, and we could have false
positives (or false negatives) in the test because the authoritative
server doesn't follow the DNS protocol for all the tests in the resolver
system test.
this test adds a record with empty non-terminal nodes above it. this
has also been observed to trigger the crash in NSEC3 zones.
NOTE: the test currently fails, because while there is no crash, the
query results are not as expected. when we add a node below an ENT,
receive_secure_serial() gets DNS_R_PARTIALMATCH, and the signed
zone is never updated. this is not a regression from fixing the
crash bug; it's a separate inline-signing bug.
test that there's no crash when querying for a newly-deleted node.
(incidentally also renamed ns3/named.conf.in to ns3/named1.conf.in,
because named2.conf.in does exist, and they should match.)
Add back the top blocks 'parental-agents', 'primaries', and 'masters'
to the configuration. Do not document them as so many names for the
same clause is confusing.
This has a slight negative side effect that a top block 'primaries'
can be referred to with a zone statement 'parental-agents' for example,
but that shouldn't be a big issue.
Having zone statements that are also top blocks is confusing, and if
we want to add more in the future (which I suspect will be for
generalized notifications, multi-signer), we need to duplicate a lot
of code.
Remove top blocks 'parental-agents' and 'primaries' and just have one
top block 'remote-servers' that you can refer to with zone statements.
The terminating conditions for the startup notify test would
occasionally get ~20 records or get +10 seconds of records due to
a bad terminating condition. Additionally 20 samples lead to test
failures. Fix the terminating condition to use the correct conditional
(-eq -> -ge) and increase the minimum number of log entries to
average over to 40.
After the rndc reload command finished, we might have queried the
database zone sooner than it was reloaded because rndc reloads zones
asynchronously if no specific zone was provided. We should wait for "all
zones loaded" in the ns1 log to be sure.
this commit removes the deprecated "sortlist" option. the option
is now marked as ancient; it is a fatal error to use it in
named.conf.
the sortlist system test has been removed, and other tests that
referenced the option have been modified.
the enabling functions, dns_message_setsortorder() and
dns_rdataset_towiresorted(), have also been removed.
This checks that "zone has A records but is not served by IPv4
servers" and "zone has AAAA records but is not served by IPv6
servers" are emitted when they should be and not when they shouldn't
be.
The dnssec-must-be-secure feature was added in the early days of BIND 9
and DNSSEC and it makes sense only as a debugging feature. There are no
reasons to keep this feature in the production code anymore.
Remove the feature to simplify the code.
when the attach-cache option is used in the options block
with an arbitrary name, it causes all views to use the same
cache. however, previously, this could cause the cache to be
deleted and a new cache created every time the server was
reconfigured. this did *not* occur when attach-cache was
used at the view level to refer back to another view's cache.
in this commit we correct the problem by checking for
pre-existing caches during reconfiguration, and moving
them from the old server cache list to the new cache list
before cleaning up and freeing the old cache list.
If ECDSAP256SHA256_SUPPORTED or ECDSAP384SHA384_SUPPORTED variables were
not present in the environment, os.environ would raise KeyError that is
not being handled in the decorator. Use os.getenv() instead.
This adds a new test directory specifically for CAMP attacks. This first
test in this test directory follows multiple CNAME chains, restarting
the max-recursion-queries counter, but should bail when the global
maximum quota max-query-count is reached.
Add another option to configure how many outgoing queries per
client request is allowed. The existing 'max-recursion-queries' is
per restart, this one is a global limit.
The ns2/managed1.conf file is created by the setup.sh script. Then, in
the tests.sh script it is moved to ns2/managed.conf. The latter file
name is in mkeys extra_artifacts, but the former one is not. This is a
problem when pytest is started with the --setup-only option as it only
runs the setup.sh script (e.g., in the cross-version-config-tests CI
job) and thus failing the "Unexpected files found" assertion.
When the tests were added, the files were generated without FIPS
compatibility in mind. That made the tests fail on recent OpenSSL
versions in FIPS mode.
So, the files were regenerated on a FIPS compliant system using the
following stanza:
$ openssl dhparam -out <file> 3072
Apparently, the old files are not valid for FIPS starting with OpneSSL
3.1.X release series as "FIPS 140-3 compliance changes" are mentioned
in the changelog:
https://openssl-library.org/news/openssl-3.1-notes/
Add support for Extended DNS Errors (EDE) error 22: No reachable
authority. This occurs when after a timeout delay when the resolver is
trying to query an authority server.
Instead of cleaning the dns_badcache opportunistically, add per-loop
LRU, so each thread-loop can clean the expired entries. This also
allows removal of the atomic operations as the badcache entries are now
immutable, instead of updating the badcache entry in place, the old
entry is now deleted from the hashtable and the LRU list, and the new
entry is inserted in the LRU.
The nslookup system test checks the count of resolved addresses in
the CNAME tests using a 'grep' match on the hostname, and ignoring
lines containing the 'canonical name' string. In order to protect
the check from intermittent failures like the 'address in use' warning
message, which then automatically resolves after a retry, edit the
'grep' matching string to also ignore the comments (as the mentioned
warning message is a comment which contains the hostname).
Add test cases which check that when a XoT primary server is
unreachable or is already marked as unreachble then the next
primary server in the list is used.
Previously a ISC_R_CANCELED result code switch-case has been added to
the zone.c:zone_xfrdone() function, which did two things:
1. Schedule a new zone transfer if there's a scheduled force reload of
the zone.
2. Reset the primaries list.
This proved to be not a well-thought change and causes problems,
because the ISC_R_CANCELED code is used not only when the whole transfer
is canceled, but also when, for example, a particular primary server is
unreachable, and named still needs to continue the transfer process by
trying the next server, which it now no longer does in some cases. To
solve this issue, three changes are made:
1. Make sure dns_zone_refresh() runs on the zone's loop, so that the
sequential calls of dns_zone_stopxfr() and dns_zone_forcexfr()
functions (like done in 'rndc retransfer -force') run in intended
order and don't race with each other.
2. Since starting the new transfer is now guaranteed to run after the
previous transfer is shut down (see the previous change), remove the
special handling of the ISC_R_CANCELED case, and let the default
handler to handle it like before. This will bring back the ability to
try the next primary if the current one was interrupted with a
ISC_R_CANCELED result code.
3. Change the xfrin.c:xfrin_shutdown() function to pass the
ISC_R_SHUTTINGDOWN result code instead of ISC_R_CANCELED, as it makes
more sense.
This change adds a "none" parameter to the query-source[-v6]
options in named.conf, which forbid the usage of IPv4 or IPv6
addresses when doing upstream queries.
On some slow systems, the test might intermittently fail due to inherent
timing issues. In our CI, this most often happens in the
system:gcc:8fips:amd64 jobs.
Reintroduce logic to apply diffs when the number of pending tuples is
above 128. The previous strategy of accumulating all the tuples and
pushing them at the end leads to excessive memory consumption during
transfer.
This effectively reverts half of e3892805d6
When a test is re-run by the flaky plugin, the TestReport outcomes
collected in the pytest_runtest_makereport() hook should be overriden.
Each of the setup/call/teardown phases is reported again and since we
care about the overall outcome, their respective results should be
overriden so that only the outcome from the final test (re)run gets
reported.
Prior to this change, it lead to a situation where an extra_artifact
generated during the test might be ignored. This was caused because the
check was skipped, since the test was incorrectly considered as "failed"
in the case where the test would fail on the first run, but pass on a
subsequent flaky rerun.
QPDB is now a default implementation for both cache and zone. Remove
the venerable RBTDB database implementation, so we can fast-track the
changes to the database without having to implement the design changes
to both QPDB and RBTDB and this allows us to be more aggressive when
refactoring the database design.
Prior to introducing the pytest runner, clean.sh files were used as a
list of files that the test is expected to leave around as artifacts and
check that no extra files were created.
With the pytest runner, those scripts are no longer used, but the
ability to detect extraneous files is still useful. Add a new
"extra_artifacts" mark which can be used for the same purpose.
The query-source option has the slight quirk of allowing the address to
be specified in two ways, either as every other source option, or as an
"address" key-value pair.
For this reason, it had a separate parsing function from other X-source
options, but it is possible to extend the parsing of other X-sources to
be generic and also handle query-source.
This commit just does that.
Add a test case for Offline KSK where during the lifespan of the Signed
Key Response a KSK rollover happens. Ensure that the correct DNSKEY,
CDNSKEY, and CDS records are published at the right times.
When the zone is initially signed, the CDNSKEY/CDS RRset is not
immediately published. The DNSKEY and signatures must propagate first.
Adjust the test to allow for this case.
Add an option to dnssec-ksr keygen, -o, to create KSKs instead of ZSKs.
This way, we can create a set of KSKS for a given period too.
For KSKs we also need to set timing metadata, including "SyncPublish"
and "SyncDelete". This functionality already exists in keymgr.c so
let's make the function accessible.
Replace dnssec-keygen calls with dnssec-ksr keygen for KSK in the
ksr system test and check keys for created KSKs as well. This requires
a slight modification of the check_keys function to take into account
KSK timings and metadata.
In the ksr system test, the test_ksr_twotone case may fail if there
are two keys with the same keytag (but different algorithms), because
one key is expected to be signing and the other is not.
Switch to regular expression matching and include the algorithm in the
search string.
