Tested with RTL8188EU and RTL8188CUS in STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4523
sys/dev/mpr/mpr_sas_lsi.c
sys/dev/mps/mps_sas_lsi.c
When mp[rs]sas_get_sata_identify returns
MPI2_IOCSTATUS_SCSI_PROTOCOL_ERROR, don't bother retrying. Protocol
errors aren't likely to be fixed by sleeping.
Without this change, a system that generated may protocol errors due
to signal integrity issues was taking more than an hour to boot, due
to all the retries.
Reviewed by: slm
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D4553
* Use the interrupt-map property to route interrupts
* Remove the IRQ rman, it's now unneeded
* Support MSI/MSI-X interrupts
With this I'm able to use the two NICs I've tested (em and msk), however
while I can boot with an AHCI devie attached it fails when any drives are
connected.
Obtained from: ABT Systems Ltd
Sponsored by: SoftIron Inc
Currently, in case when npkts >= 2, RSSI and Rx radiotap fields
will be overridden by the next packet. As a result, every packet
from this chain will use the same RSSI / radiotap data.
After this change, RSSI and radiotap structure will be filled
for every frame right before ieee80211_input() call.
Tested with RTL8188EU / RTL8188CUS, STA and MONITOR modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4487
absolute position. This seems to be correlated with only removing a single
finger. To work around this report no movement on from the first packet
when the user exits scrolling.
An implementation from rum(4) was used (it looks simpler for me).
Will be used for h/w encryption support.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4447
- Add IEEE80211_GET_SLOTTIME(ic) macro.
- Use predefined macroses to set slot time.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4044
Strictly speaking, missing devinfo is error which can be caused
by instantiating child using device_add_child() instead of
BUS_ADD_CHILD(). However, we can tolerate it.
Approved by: kib (mentor)
By using this functions, we can parse a list of tuples, each of them holds
xref and variable number of values.
This kind of list is used in DT for clocks, gpios, resets ...
Discussed with: ian, nwhitehorn
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D4316
requests which page alignment + size is greater than MAXPHYS. Right
now md(4) over vnode would use the physical buffer of the size MAXPHYS
to map a data of size MAXPHYS + page offset of the user buffer. This
typically corrupts next pbuf, or, if the pbuf used was the last pbuf
in the map, the next page after the pbuf's map.
Split request up to the size of io which fits into pbuf KVA with
alignment, and retry if a part of the bio is left unprocessed.
Reported by: Fabian Keil <fk@fabiankeil.de>
Tested by: Fabian Keil, pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
It is a part of MCDI rework to share more code among NIC families.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D4481
tables. Some drivers needed some slight re-arrangement of declarations
to accommodate this. Change the USB pnp tables slightly to allow
better compatibility with the system by moving linux driver info from
start of each entry to the end. All other PNP tables in the system
have the per-device flags and such at the end of the elements rather
that at the beginning.
Differential Review: https://reviews.freebsd.org/D3458
block. Use it in all the PNP drivers to export either the current PNP
table. For uart, create a custom table and export it using
MODULE_PNP_INFO since it's the only one that matches on function
number.
Differential Review: https://reviews.freebsd.org/D3461
Intel NVMe controllers have a slow path for I/Os that span a 128KB stripe boundary but ZFS limits ashift, which is derived from d_stripesize, to 13 (8KB) so we limit the stripesize reported to geom(8) to 4KB.
This may result in a small number of additional I/Os to require splitting in nvme(4), however the NVMe I/O path is very efficient so these additional I/Os will cause very minimal (if any) difference in performance or CPU utilisation.
This can be controller by the new sysctl kern.nvme.max_optimal_sectorsize.
MFC after: 1 week
Sponsored by: Multiplay
Differential Revision: https://reviews.freebsd.org/D4446
IAP_F_FM's as well as incorrect umask specifications for
some of the new Broadwell/Skylake PMC's. Also silvermont
had a *lot* of missing IAP_F_FM.
Sponsored by: Netflix Inc.
To reduce code duplication in common code, consolidate similar privilege
check functions.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D4480
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D4455
The hardware supports descriptors with two non-contiguous pages. This
allows issuing one descriptor for an 8k copy from/to non-contiguous but
otherwise page-aligned memory.
Sponsored by: EMC / Isilon Storage Division
Update of common code to provide a query on the MAC_SPOOFING_TX and
CHANGE_MAC privileges instead of the deprecated MAC_SPOOFING privilege.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D4436
from 1500 to 1496 bytes. The MTU should remain at 1500, extending the
frame size as per IEEE 802.3. Adding IFCAP_VLAN_MTU to the
if_capabilities field in the smsc driver solves the problem. The
datasheet for the LAN9512 chip, section 3.2.3 states that the chip
supports the extended frame.
Submitted by: rpp@ci.com.au
MFC after: 1 week
PR: 205050
include the following list of changes:
- Added eswitch ACL table management
Introduce API for managing ACL table.
This API include the following features:
1) vlan filter - for VST/VGT+ support.
2) spoofcheck.
3) robust functionality to allow/drop general untagged/tagged traffic.
4) support for both ingress and egress ACL types.
- Added loopback filter to the vacl table.
- Added multicast list set in the vPort context
- Added promiscuous mode set in the vPort context
- Set the vlan list in vPort context
1) Check caps if VLAN list is not longer than FW supports
2) Set MODIFY_NIC_VPORT_CONTEXT command
- Changed MLX5_EEPROM_MAX_BYTES from 48 to 32 so that a single EEPROM
reading cannot cross the 128-byte boundary. Previously reading the
MCIA register was done in batches of 48 bytes. The third reading
would then by-pass the 127th byte, which means that part of the low
page and part of the high page would be read at the same time, which
created a bug:
1st: 0-47 bytes
2nd: 48-95 bytes
3rd: 96-143 bytes
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4411
driver. This includes binding all interrupt and worker threads
according to the RSS configuration, setting up correct Toeplitz
hashing keys as given by RSS and setting the correct mbuf
hashtype for all received traffic.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4410
completion events can be moderated in the same way like RX completion
events. Expose this functionality by a sysctl variable.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4409
