initialize the MFUNC registers. Our old test of assuming that if this
register is set at all is not quite right. Many scenarios (including
the power-on defaults for chips w/o EEPROMs) land us in trouble. The
MFUNC0 pin should be set to signal #INTA and the MFUNC1 pin should be
set to signal #INTB of multi-socketed devices. Since my memory recalls
issues with blindly clearing the upper bytes of this register, perform
the heuristic only when both MFUNC0 and 1 are clear. We won't work
well using these pins for GPIO, and the serial interrupts won't save
us because we go out of our way to generally disable them. They are
needed to support legacy drivers for 16-bit PC Cards that are
hard-wired to specific IRQ values. Since FreeBSD never had any of
these, we configure the more reliable direct signaling. This was just
one small piece of that which had been left out back in the day.
Summary:
This has been tested on the RB800, but should work on the RB333, RB600, and
RB1100 as well.
It's currently missing ECC support, but read and write are complete.
Reviewers: imp
Reviewed By: imp
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2223
interface without breaking ABI or API compatibility with existing drivers.
The existing data structures used to communicate between the kernel and
driver portions of PPS processing contain no spare/padding fields and no
flags field or other straightforward mechanism for communicating changes
in the structures or behaviors of the code. This makes it difficult to
MFC new features added to the PPS facility. ABI compatibility is
important; out-of-tree drivers in module form are known to exist. (Note
that the existing api_version field in the pps_params structure must
contain the value mandated by RFC 2783 and any RFCs that come along after.)
These changes introduce a pair of abi-version fields which are filled in
by the driver and the kernel respectively to indicate the interface
version. The driver sets its version field before calling the new
pps_init_abi() function. That lets the kernel know how much of the
pps_state structure is understood by the driver and it can avoid using
newer fields at the end of the structure that it knows about if the driver
is a lower version. The kernel fills in its version field during the init
call, letting the driver know what features and data the kernel supports.
To implement the new version information in a way that is backwards
compatible with code from before these changes, the high bit of the
lightly-used 'kcmode' field is repurposed as a flag bit that indicates the
driver is aware of the abi versioning scheme. Basically if this bit is
clear that indicates a "version 0" driver and if it is set the driver_abi
field indicates the version.
These changes also move the recently-added 'mtx' field of pps_state from
the middle to the end of the structure, and make the kernel code that uses
this field conditional on the driver being abi version 1 or higher. It
changes the only driver currently supplying the mtx field, usb_serial, to
use pps_init_abi().
Reviewed by: hselasky@
History note: it's good to document what the driver expects like this even
if it's currently a no-op.
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
Change the nvlist_recv() function to take additional argument that
specifies flags expected on the received nvlist. Receiving a nvlist with
different set of flags than the ones we expect might lead to undefined
behaviour, which might be potentially dangerous.
Update consumers of this and related functions and update the tests.
Approved by: pjd (mentor)
Update man page for nvlist_unpack, nvlist_recv, nvlist_xfer, cap_recv_nvlist
and cap_xfer_nvlist.
Reviewed by: AllanJude
Approved by: pjd (mentor)
These include standalone X550 adapters, X552 10GbE backplane, and
X552/X557-AT 10GBASE-T; with the latter two being integrated into Xeon D SoCs.
As well, this bumps the ixgbe version number to 2.8.3, and includes updates
to shared code for support for the new devices.
Differential Revision: D2414
Reviewed by: gnn, adrian
Approved by: jfv (mentor), gnn (mentor)
- Use hardware counters for ifnet stats in igb(4) when possible. This
ensures these stats include packets that bypass the regular stack via
netmap.
- Don't derefence values off the end of the igb(4) VF stats structure.
Instead, add a dedicated if_get_counter method for igb(4) VF interfaces.
- Report missed packets on igb(4) as input queue drops rather than an
input error.
- Report bug_ring drop counts as output queue drops for igb(4) and ixgbe(4).
- Export the buf_ring drop stats for individual rings via sysctl on
ixgbe(4).
- Fix a typo that in ixl(4) that caused output queue drops to be reported
as input queue drops and input queue drops to be unreported.
Differential Revision: https://reviews.freebsd.org/D2402
Reviewed by: jfv, rstone (6)
Sponsored by: Norse Corp, Inc.
remains. Xen is planning to phase out support for PV upstream since it
is harder to maintain and has more overhead. Modern x86 CPUs include
virtualization extensions that support HVM guests instead of PV guests.
In addition, the PV code was i386 only and not as well maintained recently
as the HVM code.
- Remove the i386-only NATIVE option that was used to disable certain
components for PV kernels. These components are now standard as they
are on amd64.
- Remove !XENHVM bits from PV drivers.
- Remove various shims required for XEN (e.g. PT_UPDATES_FLUSH, LOAD_CR3,
etc.)
- Remove duplicate copy of <xen/features.h>.
- Remove unused, i386-only xenstored.h.
Differential Revision: https://reviews.freebsd.org/D2362
Reviewed by: royger
Tested by: royger (i386/amd64 HVM domU and amd64 PVH dom0)
Relnotes: yes
Instead of trying to get the keyboard repeat rate set by the BIOS just set a
default one. This allows removing the usage of x86bios from atkbd.
Sponsored by: Citrix Systems R&D
Reviewed by: jkim, delphij
Differential Revision: https://reviews.freebsd.org/D2399
MFC after: 2 weeks
Previously the mask wrapped when one or more of the mask bytes extended
past the right edge of the window. Simplify the logic and use the same
byte offset and bit in both the pattern and mask.
PR: 199648
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D2360
The change would appease the static analyzers but it is pretty much a
no-op. I need to trust static analyzers much less, especially for the
kernel.
Requested by: jkim
Currently if you ifconfig down a vtnet interface while it is being used
via netmap, the kernel panics due to trying to treat the cookie values
in the virtio rings as mbufs to be freed. When netmap is enabled, these
cookie values are pointers to something else.
Note that other netmap-aware drivers don't seem to need this as they
store the mbuf pointers in the software rings that mirror the hardware
descriptor rings, and since netmap doesn't touch those, the software
state always has NULL mbuf pointers causing the loops to free mbufs to
not do anything. However, vtnet reuses the same state area for both
netmap and non-netmap mode, so it needs to explicitly avoid looking at
the rings and treating the cookie values as mbufs if netmap is
enabled.
Differential Revision: https://reviews.freebsd.org/D2348
Reviewed by: adrian, bryanv, luigi
MFC after: 1 week
Sponsored by: Norse Corp, Inc.
This is a fix to the previous attempt in r281889, which some (most?)
keyboards.
Discussed with: emaste, jkim
Found by: clang static analyzer
CID: 1007072
CID: 1007073
CID: 1007074
On one of my systems FreeBSD will fail to boot because vt_vga gets stuck
waiting for the vertical retrace if there's no monitor attached. Fix this by
adding a timeout and exiting if the vertical retrace times out.
Sponsored by: Citrix Systems R&D
Reviewed by: emaste, dumbbell
Differential Revision: https://reviews.freebsd.org/D2397
- Vmbus multi channel support.
- Vector interrupt support.
- Signal optimization.
- Storvsc driver performance improvement.
- Scatter and gather support for storvsc driver.
- Minor bug fix for KVP driver.
Thanks royger, jhb and delphij from FreeBSD community for the reviews
and comments. Also thanks Hovy Xu from NetApp for the contributions to
the storvsc driver.
PR: 195238
Submitted by: whu
Reviewed by: royger, jhb, delphij
Approved by: royger
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Microsoft OSTC
controllers.
Call iicbus_transfer() from the device context and not from the iicbus
context.
I am committing a slightly different patch, so if something break, it is
probably my fault.
PR: 199496
Submitted by: Juraj Lutter <otis@sk.FreeBSD.org>
vt_is_cursor_in_area needs to return true if any part of the mouse
cursor is visible in the rectangle area. Replace the existing test with
a simpler version of a test for overlapping rectangles.
Differential Revision: https://reviews.freebsd.org/D2356
Reviewed by: ray
Sponsored by: The FreeBSD Foundation
are not permitted to sleep. Only use the IPMI watchdog with backends
which poll driver-initiated requests to meet this requirement.
In practice this means that watchdogs will no longer be used on systems
that use the SSIF backend.
Differential Revision: https://reviews.freebsd.org/D2062
MFC after: 2 weeks
Al kudos here for the Clang static analyzer which, unlike Coverity,
failed to flag a false positive.
Found by: clang static analyzer
CID: 1007072
CID: 1007073
CID: 1007074
MFC after: 1 week
(type 1 and type 2) as well as leaf devices (type 0). In particular,
this allows the existing PCI bus logic to save and restore capability
registers such as MSI and PCI-express work for bridge devices rather than
requiring that code to be duplicated in bridge drivers. It also means
that bridge drivers no longer need to save and restore basic registers
such as the PCI command register or BARs nor manage powerstates for the
bridge device.
While here, pci_setup_secbus() has been changed to initialize the 'sec'
and 'sub' fields in the 'secbus' structure instead of requiring the pcib
and pccbb drivers to do this in the NEW_PCIB + PCI_RES_BUS case.
Differential Revision: https://reviews.freebsd.org/D2240
Reviewed by: imp, jmg
MFC after: 2 weeks
driver's suspend and resume routines. These have been redundant no-ops
since r214065 changed the PCI bus driver to manage power states for
all devices (including type 1/2 bridge devices) during suspend and resume.
for type 0 devices, not type 1 or 2 bridges. Don't read them for bridge
devices during bus scans and return an error when attempting to read them
as ivars for bridge devices.
It is not network-specific code and would
be better as part of libkern instead.
Move zlib.h and zutil.h from net/ to sys/
Update includes to use sys/zlib.h and sys/zutil.h instead of net/
Submitted by: Steve Kiernan stevek@juniper.net
Obtained from: Juniper Networks, Inc.
GitHub Pull Request: https://github.com/freebsd/freebsd/pull/28
Relnotes: yes
RSS hash from the card. We do not need to hide that under "ifdef RSS" and should
expose that by default so others like lagg(4) can use that and avoid hashing the
traffic by themselves.
While here, improve comments and get rid of hidden/unimplemented RSS support
code for UDP.
Differential Revision: https://reviews.freebsd.org/D2296
Reviewed by: jfv, erj
Discussed with: adrian
Sponsored by: Limelight Networks
--Allow multiple open iic fds by storing addressing state in cdevpriv
--Fix, as much as possible, the baked-in race conditions in the iic
ioctl interface by requesting bus ownership on I2CSTART, releasing it on
I2CSTOP/I2CRSTCARD, and requiring bus ownership by the current cdevpriv
to use the I/O ioctls
--Reduce internal iic buffer size and remove 1K read/write limit by
iteratively calling iicbus_read/iicbus_write
--Eliminate dynamic allocation in I2CWRITE/I2CREAD
--Move handling of I2CRDWR to separate function and improve error handling
--Add new I2CSADDR ioctl to store address in current cdevpriv so that
I2CSTART is not needed for read(2)/write(2) to work
--Redesign iicbus_request_bus() and iicbus_release_bus():
--iicbus_request_bus() no longer falls through if the bus is already
owned by the requesting device. Multiple threads on the same device may
want exclusive access. Also, iicbus_release_bus() was never
device-recursive anyway.
--Previously, if IICBUS_CALLBACK failed in iicbus_release_bus(), but
the following iicbus_poll() call succeeded, IICBUS_CALLBACK would not be
issued again
--Do not hold iicbus mtx during IICBUS_CALLBACK call. There are
several drivers that may sleep in IICBUS_CALLBACK, if IIC_WAIT is passed.
--Do not loop in iicbus_request_bus if IICBUS_CALLBACK returns
EWOULDBLOCK; instead pass that to the caller so that it can retry if so
desired.
Differential Revision: https://reviews.freebsd.org/D2140
Reviewed by: imp, jhb, loos
Approved by: kib (mentor)
the index array, not a value for BMCR register. In case of IFM_10_T there
could be either MII_MEDIA_10_T or MII_MEDIA_10_T_FDX, which are 1 and 2,
accordingly. Neither matches a valid BMCR value. My guessing is that this
write is harmless, since later mii_phy_setmedia() would write a proper
value there.
The code is here since the initial checkin. Note that case IFM_100_TX has
the same comment, but a proper value of BMCR_ISO is written. So, collapse
two cases into one, always writing there BMCR_ISO.
Sponsored by: Nginx, Inc.
set any value to ifm_data. If brgphy ever to call mii_phy_setmedia(),
then the value of BRGPHY_S1000 | BRGPHY_BMCR_FDX will trigger KASSERT.
While here, remove the obfuscating macro and wrap long lines.
Sponsored by: Nginx, Inc.
its use in upcoming code.
This is inspired by something in jhb's NUMA IRQ allocation patchset.
However, the tricky bit here is that the PXM lookup for a node may
fail, requiring a lookup on the parent node. So if it doesn't
exist, don't fail - just go up to the parent. Only error out of the
lookup is the ACPI lookup returns an error.
Sponsored by: Norse Corp, Inc.
This supports e500v1, e500v2, and e500mc. Tested only on e500v2, but the
performance counters are identical across all, with e500mc having some
additional events.
Relnotes: Yes
On trackpads that had support for both, we were sending two button
events when the trackpad was pressed.
Tested by: Jakob Alvermark <jakob at alvermark.net>
MFC after: 1 week
This requires a patch to redirect the output to a separate DAC when
the headphones are used. While there, add device strings for Intel
Broadwell HDA controllers and Realtek ALC292 codecs.
MFC after: 1 week
'BUS_PROBE_DEFAULT'. This allows bhyve's 'ppt' driver to claim ownership
of the device and pass it through to the guest.
In the common case where there are no competing drivers for USB controllers
this change is a no-op.
Reviewed by: hselasky
MFC after: 2 weeks
This is only the minimum set of files needed to boot in qemu. As such it is
missing a few things.
The bus_dma code is currently only stub functions with a full implementation
from the development tree to follow.
The gic driver has been copied as the interrupt framework is different. It
is expected the two drivers will be merged by the arm intrng project,
however this will need to be imported into the tree and support for arm64
would need to be added.
This includes code developed by myself, SemiHalf, Ed Maste, and Robin
Randhawa from ARM. This has been funded by the FreeBSD Foundation, with
early development by myself in my spare time with assistance from Robin.
Differential Revision: https://reviews.freebsd.org/D2199
Reviewed by: emaste, imp
Relnotes: yes
Sponsored by: The FreeBSD Foundation
handles versions 0.1 and 0.2 of the standard on 32-bit ARM.
With this driver we can shutdown in QEMU. Further work is needed to
turn secondary cores on on boot and to support later revisions of the
specification.
Submitted by: Robin Randhawa <Robin.Randhawa at ARM.com>
Sponsored by: The FreeBSD Foundation
"Intelб╝ Processor Vendor-Specific ACPI Interface Specification",
issied Dec 2014. Previous revision 005 was from Sep 2006.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
To accomplish this, we must put the Synaptics hardware in passthrough
mode when talking to the trackpoint.
I only performed minor style modifications.
Submitted by: Jan Kokemüller <jan.kokemueller at gmail.com>
MFC after: 1 week
Enable two finger scrolling by default and disable the edge scrolling if
the touchpad has no physical zone for it. Disable directional scrolling
by default to avoid using extended buttons as scroll buttons.
Add support for ClickPad. On Lenovo laptops, this is the button
reported when one presses the touchpad.
While there, fix a problem where the extended buttons were not reporting
the button release event correctly: we need to save the state of the
buttons and report it to sysmouse until we receive a packet from the
touchpad indicating the button has been released. This makes it
possible to use an extended button to resize a window. On Lenovo
laptops, the major buttons are actually reported as extended buttons.
Tested by: many (current@)
MFC after: 1 week
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.
This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.
MFC after: 1 week
v1.1.1 2015-03-26
* Support 4Kn drive.
* Change the SCSI target ID of the disk to be the index of physical
connetion to the HBA.
* Support staggered drive spin up.
* Fix a bug that command would be timeout because of improper
interrupt service routine.
* Error handling to avoid scsi command lost which caused system
hang up.
* Fix a bug that fail to get the devcie's serial number via
FreeNAS WebGUI.
Many thanks to HighPoint for continued support of FreeBSD!
MFC after: 2 weeks
after setting up interrupt moderation but before turning interrupts on.
This matches what Realtek's r8168 Linux driver does as of version 8.039.00
and fixes problems with certain incarnations of certain MAC revisions
like the interface requiring an extra up/down-cycle after boot to start
working or DMA configuration not being adhered to.
PR: 193743, 197535
MFC after: 1 week
Submission and completion queue memory need to use a
separate DMA tag for mappings than payload buffers,
to ensure mappings remain contiguous even with DMAR
enabled.
Submitted by: kib
MFC after: 1 week
Sponsored by: Intel
Previously, if per-CPU MSI-X vectors could not be allocated,
nvme(4) would fall back to INTx with a single I/O queue pair.
This change will still fall back to a single I/O queue pair, but
allocate MSI-X vectors instead of reverting to INTx.
MFC after: 1 week
Sponsored by: Intel
under bootverbose. Every example I've seen to date has been due to
an ACPI system resource device reserving a range that overlaps with
system memory (which ram0 attempts to reserve) or a local or I/O APIC
(which apic0 attempts to reserve). These are always harmless but look
scary to users.
MFC after: 1 week
I .. stupidly added code to return HAL_ANI_STATS to HAL_DIAG_ANI_STATS.
I discovered this in a noisy environment when the returned values were
enough to .. well, make everything terrible.
So - restore functionality.
Tested:
* AR5416 (uses the AR5212 HAL), in a /very/ noisy 2GHz environment.
Enough to trigger ANI to get upset and generate useful data.
These are similar to the mips24k performance counters - some are
available on perfcnt0/3, some are available on perfcnt1/4.
However, the events aren't all the same.
* Add the events, named the same as from Linux oprofile.
* Verify they're the same as "MIPS32(R) 74KTM Processor Core Family
Software User's Manual"; Document Number: MD00519; Revision 01.05.
* Rename INSTRUCTIONS to something else, so it doesn't clash with
the alias INSTRUCTIONS. I'll try to tidy this up later; there
are a few other aliases to add and shuffle around.
Tested:
* QCA9558 SoC (AP135 board) - MIPS74Kc core (no FPU.)
* make universe; where it didn't fail for other reasons.
TODO:
* It'd be nice to support the four performance counters
in at least this hardware, rather than just two.
Reviewed by: bsdimp ("looks good; don't break world".)
Previously, the driver was trying to blink the LED in the newstate
function, but that only gets called once (unlike OpenBSD's net80211
stack). Move the LED blinking to set_channel().
While there, don't try to set the channel when we switch to the SCAN
state. This is already accomplished by the set_channel() function.
MFC after: 1 week
work stack and is reused again on the receive ring. Remaining received packets in the ring are not processed in that
invocation of bxe_rxeof() and defered to the task thread.
MFC after: 5 days
There are cases when gpioled nodes in DTS come from different sources
(e.g. standard Beaglebone Black LEDs in main DTS + shield LEDs in
overlay DTS) so instead of handling only first compatible node go
through all child nodes
- bus_dmamap_create() does not take the BUS_DMA_NOWAIT flag
- properly unload maps
- do not assign NULL to dma map pointers
Submitted by: Konstantin Belousov <kostikbel@gmail.com>
Approved by: jfv (mentor)
MFC after: 1 week
the top-level HAL.
The athstats program is blindly using a copy of the ar5212 ANI stats structure
to pull out ANI statistics/state and this is problematic for the AR9300
HAL.
So:
* Define HAL_ANI_STATS and HAL_ANI_STATE
* Use HAL_ANI_STATS inside the AR5212 HAL
This commit doesn't (yet) convert the ar5212AniState -> HAL_ANI_STATE when
exporting it to userland; that'll come in the next commit.
specially aml8726-m6 and aml8726-m8b SoC based devices.
aml8726-m6 SoC exist in devices such as Visson ATV-102.
Hardkernel ODROID-C1 board has aml8726-m8b SoC.
The following support is included:
Basic machdep code
SMP
Interrupt controller
Clock control driver (aka gate)
Pinctrl
Timer
Real time clock
UART
GPIO
I2C
SD controller
SDXC controller
USB
Watchdog
Random number generator
PLL / Clock frequency measurement
Frame buffer
Submitted by: John Wehle
Approved by: stas (mentor)
uintptr_t may be 64-bit on some platforms, therefore when
finding xrefinfo by pointer to device the high word is being
cut off due to cast to phandle_t which is 32-bit long by definition.
Due to that we loose the high word of the address to compare with
xi->dev's address.
To fix that, first argument of xrefinfo_find() is extended to
uintptr_t and is being cast to appropriate type (phandle_t)
when compared.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Reviewed by: nwhitehorn
Obtained from: Semihalf
Handle the VIRQ_DEBUG signal and print a stack trace of each vCPU on the Xen
console. This is only used for debug purposes and is triggered by the
administrator of the Xen host.
Sponsored by: Citrix Systems R&D
MFC after: 1 week
rathe than private in each HAL module.
Whilst here, modify ath_hal_private to always have the per-channel
noisefloor stats, rather than conditionally. This just makes
life easier in general (no strange ABI differences between different
HAL compile options.)
Add a couple of methods (clear/reset, add) rather than using
hand-rolled versions of things.
This symptom is "calibrations don't ever run", which may cause some
pretty spectacularly bad behaviour in noisy environments or with longer
uptimes.
Thanks to dtrace to make it easy to check if specific non-inlined functions
are getting called by things like the ANI and calibration HAL methods.
Grr.
Tested:
* AR9380, STA mode
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri May 31 12:17:08 2013 +0000
drm: Sort connector modes based on vrefresh
Keeping the modes sorted by vrefresh before the pixel clock makes the
mode list somehow more pleasing to the eye.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
PR: 198936
Obtained from: Linux
MFC after: 1 month
MFC with: r280183
which showed up after I started changing addresses this early.
It turns out that there's some other malarky going on behind the scenes
in the HAL and merely setting the net80211/ifp mac address this early
isn't enough. If the MAC is set from kenv at attach time, the HAL
also needs to be programmed early.
Without this, the VAP wouldn't work enough for finishing association -
probe requests would be fine as they're broadcast, but association
request would fail.
This is used by the AR71xx platform code to choose a local MAC based on
the "board MAC address", versus whatever potentially invalid/garbage
values are stored in the Atheros calibration data.
common (autogenerated) versions. Removes extra vertical space,
and makes it easier to grep for usage throughout the tree.
Conditionally compile only for arm6 [1] (yes sounds odd but is right).
Submitted by: andrew [1]
Reviewed by: gnn, andrew (ian earlier version I think)
Differential Revision: https://reviews.freebsd.org/D2159
Obtained from: Cambridge/L41
Sponsored by: DARPA, AFRL
duplicated code in the two classes, and also allows devices in FDT-based
systems to declare simplebus as their parent and still work correctly
when the FDT data describes the device at the root of the tree rather
than as a child of a simplebus (which is common for interrupt, clock,
and power controllers).
Differential Revision: https://reviews.freebsd.org/D1990
Submitted by: Michal Meloun
the PMC_IN_KERNEL() macro definition.
Add missing macros to extract the return address (LR) from the trapframe.
Discussed with: andrew
Obtained from: Cambridge/L41
Sponsored by: DARPA, AFRL
MFC after: 2 weeks
statements. This allows for setting all PCM core parameters in the
kernel environment through loader.conf(5) or kenv(1) which is useful
for pluggable PCM devices like USB audio devices which might be
plugged after that sysctl.conf(5) is executed.
the right solution but I will leave it to experts to untangle this
problem to properly stop the build failures.
At the moment only if_ix.c includes dev/netmap/ixgbe_netmap.h which is
good as ixgbe_netmap.h defines a couple of (file) static variables--thus
local to if_ix.c.
static int ix_crcstrip however now also got checked from ix_txrx.c
(as an extern) and should not be visible there. In fact we do see
powerpc and powerpc64 build failures because of this. It is unclear
to me why on other (clang built?) architectures this does not lead
to a reference of an undefined symbol and similar build breakage.
This is a temporary workaround until we determine a reliable sequence
of operations for detecting MC reboots.
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D2084
bus_space_*_8() are not always macros, so it is not correct to use
#ifndef.
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D2083
Tx multi queue is added in FreeBSD 8.0. So, the changeset drops earlier
versions support.
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D2081
In theory the barriers are required to cope with write combining and
reordering. Two barriers are added (sometimes merged to one):
1. Before the first write to guarantee that previous writes to the region
have been done
2. Before the last write to guarantee that write to the last dword/qword is
done after previous writes
Barriers are inserted before in the assumption that it is better to
postpone barriers as much as it is possible (more chances that the
operation has already been already done and barrier does not stall CPU).
On x86 and amd64 bus space write barriers are just compiler memory barriers
which are definitely required.
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D2077
ioctl to put interface down sets ifp->if_flags which holds the intended
administratively defined state and calls driver callback to apply it.
When everything is done, driver updates internal copy of
interface flags sc->if_flags which holds the operational state.
So, transmit from Rx path is possible when interface is intended to be
administratively down in accordance with ifp->if_flags, but not applied
yet and the operational state is up in accordance with sc->if_flags.
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D2075
appears to be too inaccurate that it can be used to synchronize the
playback data stream. If there is a recording endpoint associated with
the playback endpoint, use that instead. That means if the isochronous
OUT endpoint is asynchronus the USB audio driver will automatically
start recording, if possible, to get exact information about the
needed sample rate adjustments. In no recording endpoint is present,
no rate adaption will be done.
While at it fix an issue where the hardware buffer pointers don't get
reset at the first device PCM trigger.
Make some variables 32-bit to avoid problems with multithreading.
MFC after: 3 days
PR: 198444
Many thanks to ian who gently provided me the DS1307 breakout board.
Tested on: Raspberry pi
Differential Revision: https://reviews.freebsd.org/D2022
Reviewed by: rpaulo
* Fix the multiple same-named devclasses; the duplicate name
trips up the linker.
* Re-do the taskqueue stuff to use the new cpuset API, not the old
pinned API.
* Add includes for the new location of the RSS configuration routines.
This allows ixgbe to compile as a module /and/ linked into the kernel,
along with RSS working.
Sponsored by: Norse Corp, Inc.
Overview:
* implemented quirk for forcing SATA interface enable
* restore value to status register - this enables link autonegotiation
Modifications:
* devid:vendorid field
* quirk for forcing PI setting (BIOS is doing that on PC-like systems)
* write to capabilites field to enable phy link initialization
Submitted by: Wojciech Macek <wma@semihalf.com>
Reviewed by: imp, mav
Obtained from: Semihalf
This update brings few features:
o Support for the setmaster/dropmaster ioctls. For instance, they
are used to run multiple X servers simultaneously.
o Support for minor devices. The only user-visible change is a new
entry in /dev/dri but it is useless at the moment. This is a
first step to support render nodes [1].
The main benefit is to greatly reduce the diff with Linux (at the
expense of an unreadable commit diff). Hopefully, next upgrades will be
easier.
No updates were made to the drivers, beside adapting them to API
changes.
[1] https://en.wikipedia.org/wiki/Direct_Rendering_Manager#Render_nodes
Tested by: Many people
MFC after: 1 month
Relnotes: yes
- Split the driver into independent pf and vf loadables. This is
in preparation for SRIOV support which will be following shortly.
This also allows us to keep a seperate revision control over the
two parts, making for easier sustaining.
- Make the TX/RX code a shared/seperated file, in the old code base
the ixv code would miss fixes that went into ixgbe, this model
will eliminate that problem.
- The driver loadables will now match the device names, something that
has been requested for some time.
- Rather than a modules/ixgbe there is now modules/ix and modules/ixv
- It will also be possible to make your static kernel with only one
or the other for streamlined installs, or both.
Enjoy!
Submitted by: jfv and erj
Drops are observed under multi-stream TCP traffic due to put-list
overflow with limit equal to 64.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Transmit may be called when TxQ is not started yet (i.e. txq->common is
invalid). TxQ state is checked below when mbuf is processed and dropped
if TxQ is not started.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
The information is required for NIC update and config tools.
Submitted by: Artem V. Andreev <Artem.Andreev at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It is done to structure sysctl and do not mix with Tx queue statistics
to be added.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
handle_ddp_close() function in t4_ddp.c as the logic is similar
to handle_ddp_data(). This allows all knowledge of the special
DDP mbufs to be private to t4_ddp.c as well.
device restart.
(Committers note - once scan overhaul and a few other things have been
fixed in net80211 to not block things in the taskqueue, this can disappear
and the device specific taskqueues in other drivers can also go away.)
PR: kern/197143
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
fixes various races between wpi_notif_intr() and wpi_stop_locked().
(attachment 154381)
Committers note: yes, unlock/if_input/lock has to go away, but that'll
have to be done later.
PR: kern/197143
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
(Committer note: these checks will have to be re-established in a future
commit as /well/ as having the KASSERTs.)
PR: kern/197143
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
strings returned to userland include the nulterm byte.
Some uses of sbuf_new_for_sysctl() write binary data rather than strings;
clear the SBUF_INCLUDENUL flag after calling sbuf_new_for_sysctl() in
those cases. (Note that the sbuf code still automatically adds a nulterm
byte in sbuf_finish(), but since it's not included in the length it won't
get copied to userland along with the binary data.)
Remove explicit adding of a nulterm byte in a couple places now that it
gets done automatically by the sbuf drain code.
PR: 195668
This is slightly different to the other switches - the VLAN table
(VTU) programs in the vlan port mapping /and/ the port config
(tagged, untagged, passthrough, any.)
So:
* Add VTU operations to program the VTU (vlan table)
* abstract out the mirror-disable function so it's .. well, a function.
* setup the port to have a dot1q configuration for dot1q - the
port security is VLAN (not per-port VLAN) and requires an entry
in the VLAN table;
* add set_dot1q / get_dot1q to program the VLAN table;
* since the tagged/untagged ports are now programmed into the VTU,
rather than global - plumb the ports /and/ untagged ports bitmaps
through the arswitch API.
Tested:
* AP135 - QCA9558 SoC + AR8327N switch
not on head.. otherwise the file pointer will be NULL and when
you try to do something with it you will crash. Make the #else
be the old capabilites, and then remove the erroneous ifdefs for
11.
MFC after: 1 week (with the other MFC I was going to do until the panic)
A late change to the SR-IOV infrastructure broke passthrough of
VFs. device_set_devclass() was being used to try to force the
ppt driver to attach to the device, but this didn't work because
the DF_FIXEDCLASS flag wasn't being set on the device, so the
ppt driver probe routine would not match when it returned
BUS_NOWILDCARD. Fix this by adding a new device function that
both sets the devclass and sets the DF_FIXEDCLASS flag, and use
that to force the ppt driver to attach to VFs.
Differential Revision: https://reviews.freebsd.org/D2041
Reviewed by: jhb
MFC after: 3 weeks
adding this major feature to the driver. Secondly, this updates the base
driver with new 20G device support, and with the new firmware levels some
changes to link handling and initialization were required.
MFC after: 1 week
The MEM_UOPS_RETIRED actually work the same way as the Sandy
Bridge counters, but the counters were documented in a different
way and that seemed to cause the Ivy Bridge counters to be
implemented incorrectly. Use the same counter definitions as
Sandy Bridge. While I'm here, rename the counters to match
what's documented in the datasheet.
Differential Revision: https://reviews.freebsd.org/D1590
MFC after: 1 month
Sponsored by: Sandvine Inc.
On Sandy Bridge and later, to count branch-related events you
have to or together a mask indicating the type of branch
instruction to count (e.g. direct jump, branch, etc) and a bits
indicating whether to count taken and not-taken branches. The
current counter definitions where defining this bits individually,
so the counters never worked and always just counted 0.
Fix the counter definitions to instead contain the proper
combination of masks. Also update the man pages to reflect the
new counters.
Differential Revision: https://reviews.freebsd.org/D1587
MFC after: 1 month
Sponsored by: Sandvine Inc.
A couple of pmc counters did not work because there were being
restricted to the wrong PMC unit. I've verified that these
counters now work and match the documented restrictions.
Differential Revision: https://reviews.freebsd.org/D1586
MFC after: 1 month
Sponsored by: Sandvine Inc
- Bump link state when stopping or starting the interface;
- Don't handle SIOCGIFADDR specially, similar to r277103.
This change is based on a previous revision from Andy Zhang
(Microsoft) who did the diagnostic work and many thanks to
them for their help in supporting the HyperV work.
PR: kern/187203
MFC after: 2 weeks
All the per-port support is really doing is applying a port visibility
mask to each of the switchports. Everything still look like a single
portgroup (vlan id 1), but the per-port visibility mask is modified.
Whilst I'm here, also add some initial dot1q support - the pvid stuff
is doing the right thing, but it's not useful without the rest of
the VLAN table programming.
It's enough for me to be able to use the LAN/WAN port distinction
on the AP135, where there isn't (for now!) a dedicated PHY for the
"WAN" port.
Tested:
* AP135, QCA9558 SoC + AR8327 switch
been done by U-Boot. This allows the USB to work when we load the kernel
directly.
No dma sync is performed after these operations as the data we read/write
is not used by the cpu after the calls to the maimbox driver.
Differential Revision: https://reviews.freebsd.org/D1940
Reviewed by: imp, Michal Meloun (meloun AT miracle.cz)
MFC after: 1 Week
Sponsored by: ABT Systems Ltd
* Even though I got the registers around "right", it seems
I'm not tickling the MDIO access correctly for the internal PHY
bus. Some of the switches are fine poking at the external PHY
registers; others aren't. So, enable direct PHY bus access
for the AR8327, and leave the existing code in place for the
others.
* Go and shuffle the register access around. Whilst here,
restore the 2ms delay if changing page.
* Comment out some of the stub printf()s; there's some upcoming
work to add port VLAN support.
Tested:
* AP135 development board
* Carambola2 - AR9331 SoC
When a gpiobus child is added, use its name to identify the mapped pin
names.
Make the respective changes to libgpio.
Add a new '-n' flag to gpioctl(8) to set the pin name.
Differential Revision: https://reviews.freebsd.org/D2002
Reviewed by: rpaulo
Requested by: many
The vtophys() function is used to get the physical page address for
the virtually allocated frame buffers when a physically continuous
memory area is not available. This change also allows removing the
masking of the FB_FLAG_NOMMAP flag in the PS3 syscons driver.
The FB and VT drivers were tested using X.org/xf86-video-scfb and
syscons.
uart implementations, and export them using the new linker-set mechanism.
Differential Revision: https://reviews.freebsd.org/D1993
Submitted by: Michal Meloun
(class and device) FDT UART. Define second one, UART_FDT_CLASS, for UART
class only.
This paves the way for declaring uart_class data and ofw/fdt compat data
with a uart implementation, rather than needing a big global table of
compat data and weak-symbol declarations of every existing implementation.
Differential Revision: https://reviews.freebsd.org/D1992
Submitted by: Michal Meloun
netmap rx queues, and the "batchiness" of rx updates sent to the chip.
These knobs will probably become per-rxq in the near future and will be
documented only after their final form is decided.
MFC after: 1 month
rework the code a little bit to use this function consistently to cleanup
all the changes made as part of the probe phase.
This fixes an issue where a FDT child node without a matching driver could
leave the GPIO pins mapped and prevent the further use of them.
This prints a warning when your system have a hinted child or a FDT child
node for which you don't have a matching driver:
gpiobus0: <unknown device> at pin(s) 24 irq 24
is the case, depending on the options, in some of the ARM hardware
simulators. In these cases we don't get an interrupt so will need to
schedule the task to write more data to the uart.
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
This new function can be used by other drivers to reserve the use of GPIO
pins.
Anyway, the use of ofw_gpiobus_parse_gpios() is preferred when possible.
Requested by: Michal Meloun
the CPU nexus.
* Add ahb as a possible bus attachment
* Lay a comment down to remind me or whoever else ends up trying
to debug why the EEPROM isn't mapped in as to what's going on.
I noticed that openwrt/linux does this, citing "instability", so
until they figure out why I'm going to disable it here as well.
Tested:
* QCA AP135 - QCA955x SoC + AR8327 switch.
So, it turns out that the AR8327 has 7 ports internally:
* GMAC0 / external (CPU) MAC0
* GMAC1 / port1 -> GMAC5 / port5: external switch port PHYs
* GMAC6 / external (CPU) MAC1
Now, depending upon how things are wired up, the second CPU port (MAC1)
can be wired to either the switch (port6), or through port5's PHY, bypassing
the GMAC+switch entirely. Ie, it can pretend to be a boring PHY, saving
system designers from having to include a separate PHY for a "WAN" port.
Here's the rub - the AP135 board (QCA955x SoC) hooks up arge0 to
the second CPU port on the AR8327, but it's hooked up as RGMII.
So, in order to hook it up to the rest of the switch, it isn't configured
as a separate PHY - OpenWRT has it setup as connected via RGMII to
GMAC6 and (I'm guessing) it's set to be a WAN port by configuring up
port-based VLANs or something.
Thus, with a port mask of 0x3f, GMAC6 was never allowed to receive traffic
from any other port. It could transmit fine, but not receive anything.
So, now it works enough for me to continue doing board bootstrapping.
Note, this isn't enough to make the QCA955x + AR8327 work - there's
a bunch of uncommitted work to both the platform SoC (interrupt handling,
ethernet, etc) and the ethernet switch (register access space, setup, etc)
that needs to happen. However, this particular change is also relevant to
other SoCs, like the AR934x and AR7161, both of which can be glued to
this switch.
Tested:
* AP135 development board
TODO:
* Figure out whether I can somehow abuse another port mode to have this
be a pass-through PHY, or whether I should just create some more boot
time hints to explicitly set up port-based isolation so this works
in a more useful way by default.
The main purpose of this feature is to be able to unload a KMS driver.
When going back from the current vt(4) backend to the previous backend,
the previous backend is reinitialized with the special VDF_DOWNGRADE
flag set. Then the current driver is terminated with the new "vd_fini"
callback.
In the case of vt_fb and vt_vga, this allows the former to pass the
vgapci device vt_fb used to vt_vga so the device can be rePOSTed.
Differential Revision: https://reviews.freebsd.org/D687
Pass all SR-IOV configuration to the kernel using an nvlist. The
main benefit that this offers is flexibility. It allows a driver
to accept any number of parameters of any type supported by the
SR-IOV configuration infrastructure with having to make any
changes outside of the driver.
It also offers the user very fine-grained control over the
configuration of the VFs -- if they want, they can have different
configuration applied to every VF.
Differential Revision: https://reviews.freebsd.org/D82
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
Add a function that validates that the user-provided SR-IOV
configuration is valid. This includes basic checks that the
structure of the configuration is correct (e.g. all required
configuration nodes are present) as well as validating against
a configuration schema.
The schema validation consists of:
- Ensuring that all required config parameters are present.
- If the schema defines a default value for a parameter,
adding the default value if the parameter is not set.
- Ensuring that no parameters are specified in the config
that are not defined in the schema.
- Ensuring that have the correct type defined in the schema.
- Ensuring that no configuration nodes are present for devices
that do not exist. For example, if 2 VFs are configured,
then we validate that a node called VF-5 does not exist.
Differential Revision: https://reviews.freebsd.org/D81
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
When creating VFs, we must size each SR-IOV BAR on the PF and
allocate a configuous I/O memory window large enough for every VF.
However, the window only needs to be aligned to a boundary equal
to the size of the window for a single VF.
When a VF attempts to allocate an I/O memory resource, we must
intercept the request in the pci driver and pass it off to the
SR-IOV code, which will allocate the correct window from the
pre-allocated memory space for the PF.
Inform the pci driver about the size and address of the BARs on
the VF when the VF is created. This is required by pciconf -b and
bhyve.
Differential Revision: https://reviews.freebsd.org/D78
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
The SR-IOV standard requires VFs to read all-ones when the VID
and DID registers are read. The VMM (hypervisor) is required to
emulate them instead. Make pci_read_config() do this emulation.
Change pci_user.c to use pci_read_config() to read config space
registers instead of going directly to the pcib so that the
emulated VID/DID registers work correctly on VFs. This is
required both for pciconf and bhyve PCI passthrough.
Differential Revision: https://reviews.freebsd.org/D77
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
Implement the interace to create SR-IOV Virtual Functions (VFs).
When a driver registers that they support SR-IOV by calling
pci_setup_iov(), the SR-IOV code creates a new node in /dev/iov
for that device. An ioctl can be invoked on that device to
create VFs and have the driver initialize them.
At this point, allocating memory I/O windows (BARs) is not
supported.
Differential Revision: https://reviews.freebsd.org/D76
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
Refactor PCI resource allocation code to allow a request for a
memory-mapped I/O window that is a multiple of a requested size.
This is needed by the SR-IOV code because the VF BARs are all
allocated contiguously. We can't just allocate a resource that is
a multiple of a single VF BAR because the size of an allocation
implies its alignment requirement.
Differential Revision: https://reviews.freebsd.org/D71
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
Refactor creation of PCI devices into helper methods that can be
used by the VF creation code.
Differential Revision: https://reviews.freebsd.org/D67
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
watchdog.c does an #ifdef DDB but does not #include "opt_ddb.h".
Fixing this turned up a missing include file.
MFC after: 1 week
X-MFC-With: r261495, r279410
property for devices that doesn't descend directly from gpiobus.
The parser supports multiple pins, different GPIO controllers and can use
arbitrary names for the property (to match the many linux variants:
cd-gpios, power-gpios, wp-gpios, etc.).
Pass the driver name on ofw_gpiobus_add_fdt_child(). Update gpioled to
match.
An usage example of ofw_gpiobus_parse_gpios() will follow soon.
I2C real-time clock (RTC).
The DS3231 has an integrated temperature-compensated crystal oscillator
(TXCO) and crystal.
DS3231 has a temperature sensor, an independent 32kHz output (which can be
turned on and off by the driver) and another output that can be used as
interrupt for alarms or as a second square-wave output, which frequency and
operation mode can be set by driver sysctl(8) knobs.
Differential Revision: https://reviews.freebsd.org/D1016
Reviewed by: ian, rpaulo
Tested on: Raspberry pi model B
The current GSO implementation in netback is broken and causes errors on the
guest tx path. While this is fixed disable GSO in order to have a working
netback.
Sponsored by: Citrix Systems R&D
Discussed with: gibbs
The optimization made in r239940 is valid for struct mbuf's current structure
and size in FreeBSD, but hardcodes assumptions about sizes of struct mbuf,
which are unfortunately broken if additional data is added to the beginning of
struct mbuf
X-MFC note (discussed with rwatson):
This change requires the MPKTHSIZE definition, which is only available after
head@r277203 and will not be MFCed as it breaks mbuf(9) KPI.
A direct commit to stable/10 and merges to other branches to add the necessary
definitions to work with the code as-is will be done to facilitate this MFC
PR: 194314
MFC after: 2 weeks
Approved/Reviewed by: erj, jfv
Sponsored by: EMC / Isilon Storage Division
Provide sys/dev/fdt/simplebus.h with the class declaration so that it
is possible to subclass FDT simplebus.
Differential Revision: https://reviews.freebsd.org/D1886
Reviewed by: nwhitehorn, imp
Summary:
For new eMMC chips, we must signal controller HC capability in OP_COND command.
Reviewers: imp, ian
Reviewed By: ian
Differential Revision: https://reviews.freebsd.org/D1920
With the patch applied the number of instruction events is 1% less and
number of mispredicted branch events is 5% less under multistream TCP
traffic load close to line rate.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
CDAI_FLAG_NONE advanced information CCB flag.
Support for the flag was merged to stable/10 in r279329, and the
__FreeBSD_version in stable/10 was bumped to 1001510.
Check for that version in the mps(4) and mpr(4) drivers when determining
whether to use the flag.
Sponsored by: Spectra Logic
MFC after: 3 days
dates.
- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).
- Added a sysctl variable to control how StartStopUnit behavior works. User can
select to spin down disks based on if disk is SSD or HDD.
- Inquiry data is required to tell if a disk will support SSU at shutdown or
not. Due to the addition of mpssas_async, which gets Advanced Info but not
Inquiry data, the setting of supports_SSU was moved to the
mpssas_scsiio_complete function, which snoops for any Inquiry commands. And,
since disks are shutdown as a target and not a LUN, this process was
simplified by basing it on targets and not LUNs.
- Added a sysctl variable that sets the amount of time to retry after sending a
failed SATA ID command. This helps with some bad disks and large disks that
require a lot of time to spin up. Part of this change was to add a callout to
handle timeouts with the SATA ID command. The callout function is called
mpssas_ata_id_timeout(). (Fixes PR 191348)
- Changed the way resets work by allowing I/O to continue to devices that are
not currently under a reset condition. This uses devq's instead of simq's and
makes use of the MPSSAS_TARGET_INRESET flag. This change also adds a function
called mpssas_prepare_tm().
- Some changes were made to reduce code duplication when getting a SAS address
for a SATA disk.
- Fixed some formatting and whitespace.
- Bump version of mps driver to 20.00.00.00-fbsd
PR: 191348
Reviewed by: ken, scottl
Approved by: ken, scottl
MFC after: 2 weeks
It is disabled by default but users can set IFCAP_TXCSUM on the
netmap ifnet (ifconfig ncxl0 txcsum) to override netmap and force
the hardware to calculate and insert proper IP and L4 checksums in
outbound frames.
MFC after: 2 weeks
when re-enumerating a FULL speed device. Else the wrong max packet
setting might be used when trying to re-enumerate a FULL speed device.
MFC after: 3 days
Preliminary tests indicate 32 Mpps on tx, 24 Mpps on rx
with source and receiver on two different ports of the same 40G card.
Optimizations are likely possible.
The code follows closely the one for ixgbe so i do not
expect stability issues.
Hardware kindly supplied by Intel.
Reviewed by: Jack Vogel
MFC after: 1 week
To delay packets from a particular TX queue by a particular time, write a value
into the TX Pace table s.t. pace time <= TX Pace Clock Period * (2 ^ pace value)
- the TX pace clock is 1/13 of the system clock, so its period should be 104 or
52 ns depending on whether turbo mode is active.
EFX_TX_PACE_CLOCK_BASE added by me.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It solves locking problem when EFSYS_MEM_ALLOC is called in
the context holding a mutex (not allowed to sleep).
E.g. on interface bring up or multicast addresses addition.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It is one more place missed in the previous fix.
Most likely is was just memory leak on the error handling path since
typically efsys_mem_t is filled in by zeros on allocation.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Host-bus byte order translation is not requred.
Submitted by: Artem V. Andreev <Artem.Andreev at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Use remaining number of DMA segment instead of maximum number in mapping
when checking space for one more TSO segment packet.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Sync endif comment with conditional.
BOOTROM and SIENA_BOOTROM are the same, but highlight that it is Siena.
Restore commented out assertion.
Sync comments with out-of-tree driver.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Before the common code had hard coded limits on the IDs RXQs and TXQs could
be created with which were suited for the Windows driver with VMQ, and so
would prevent queues with IDs greater than or equal to 259 (for TXQs) or 768
(for RXQs) from being created. This change allows the limits to be set in
efsys.h, so that all 1024 queues can be created during new manftest tests.
Also, the descriptor cache sizes were also hard coded to values suited to
the smaller queue counts, and so it was necessary to make them configurable
as well.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Caught when efx_filter_init() failed and called efx_filter_fini() in the
teardown path.
Submitted by: Andrew Lee <alee at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Previously the driver's view was the expected outcome of any
reconfiguration even if that reconfiguration failed.
Submitted by: Ben Horgan
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
We must not enable RX queues with random parameters when they are
mapped into a VF with an untrusted driver. It's probably not a good
idea to do this anyway, so take this bit out of the table test masks.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Otherwise when processing finally comes to efx_tx_qdesc_post() it could
be insufficient space between reaped and added to post pending
descriptors.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
efx_ev_mcdi() does not assert or check that all event handlers it
calls are non-null. Add assertions at the top for all required
event handlers, as some events (in the case of this bug, monitor
events) are rare.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Use nitem() to get number of array elements.
Remove unused define.
Use TAB to indent.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
TCP header is fragmented in the case of VLAN tagged IPv6 traffic without
HW VLAN tagging.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
will be used with arm64 to find which cpus to enable, and could also be
used with 32-bit arm and mips for the same purpose.
Differential Revision: https://reviews.freebsd.org/D1825
Sponsored by: The FreeBSD Foundation
This will be needed by arm64 to find the value to pass to the psci (Power
State Coordination Interface) driver, among other things, used to enable
cores.
Differential Revision: https://reviews.freebsd.org/D1824
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
properly.
If there is garbage in the flags field, it can sometimes include a
set CDAI_FLAG_STORE flag, which may cause either an error or
perhaps result in overwriting the field that was intended to be
read.
sys/cam/cam_ccb.h:
Add a new flag to the XPT_DEV_ADVINFO CCB, CDAI_FLAG_NONE,
that callers can use to set the flags field when no store
is desired.
sys/cam/scsi/scsi_enc_ses.c:
In ses_setphyspath_callback(), explicitly set the
XPT_DEV_ADVINFO flags to CDAI_FLAG_NONE when fetching the
physical path information. Instead of ORing in the
CDAI_FLAG_STORE flag when storing the physical path, set
the flags field to CDAI_FLAG_STORE.
sys/cam/scsi/scsi_sa.c:
Set the XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE when
fetching extended inquiry information.
sys/cam/scsi/scsi_da.c:
When storing extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_STORE instead of
ORing it into a field that isn't initialized.
sys/dev/mpr/mpr_sas.c,
sys/dev/mps/mps_sas.c:
When fetching extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE instead of
setting it to 0.
sbin/camcontrol/camcontrol.c:
When fetching a device ID, set the XPT_DEV_ADVINFO flags
field to CDAI_FLAG_NONE instead of 0.
sys/sys/param.h:
Bump __FreeBSD_version to 1100061 for the new XPT_DEV_ADVINFO
CCB flag, CDAI_FLAG_NONE.
Sponsored by: Spectra Logic
MFC after: 1 week
temporary buffer when remaining space is not enough to hold
a whole block.
- yarrow.c: add a comment that we intend to change the code and remove
memcpy's in the future. (*)
Requested by: markm (*)
Reviewed by: markm
Approved by: so (self)
Allocate the minimum or maximum response length for GET_BOARD_CFG as
appropriate. When looking up firmware subtypes by partition ID,
check the ID against the actual response length.
Merge of the patch made by Ben Hutchings in 2011.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Mainly to unify with similar member for transmit and receive queues.
It will be used in the future for resources allocation processing.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It avoids access to m_pkthdr when TSO packet is started and also makes
tso_start_new_packet() function smaller.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
sometimes. It will power up wrong and identify itself badly:
cardbus0: <network, ethernet> at device 0.0 (no driver attached)
cardbus0: <simple comms, UART> at device 0.1 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.2 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.3 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.4 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.5 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.6 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.7 (no driver attached)
All the higher numbered functions (.2 and above) have a config space
of all 0's. This smells a bit like a special debug mode, but the
current atheros driver doesn't cope. It is unclear if this card is
just a flake, or if we're doing something wrong in the power-up
sequence.
Put a work around into the code that tests for this rather unusual
condition. If we power a CardBus device up, and the device says it is
multi-function, and any of the functions have a 0 device ID, try the
power-up sequence again.
randomdev_init_reader to change read_random over to the newly installed
adaptor was missed. This means both read_random and arc4random (seeded
from read_random) were not returning very random data. This also
effects userland arc4random as it is seeded from kernel arc4random.
The random devices are uneffected and have returned good randomness
since the change.
All keys generated with a kernel of r273872 must be regenerated with
a kernel with this patch. Keys generated may be predictable.
Remove the warning as log is too early to print anything, and it would
always get printed due to early use of arc4random...
Reviewed by: delphij, markm
Approved by: so (delphij)
Highlights:
- Multiple verbs API updates
- Support for RoCE, RDMA over ethernet
All hardware drivers depending on the common infiniband stack has been
updated aswell.
Discussed with: np @
Sponsored by: Mellanox Technologies
MFC after: 1 month
interrupt status bit. According to the UHCI controller specification
the host controller halted interrupt is non-maskable.
PR: 156596
Tested by: adrian @
MFC after: 1 week
identifies the tested condition for _PRT as "BYTE value of 0", so the
remaining part of the conditionals is sufficient.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
This is to avoid a witness warning about a waiting memory allocation in
the evnt hanlder registration code.
Reported by: markj
MFC after: 3 days
X-MFC with: r277795
Xenstore user-space device has two problems currently:
- It does not correctly handle concurrent clients, because it's storing
each client data in dev->si_drv1.
- It does not correctly free this data when the client closes the device.
In order to solve both of this issues store the per-client data using
cdevpriv, which also comes with a hook in order to perform the necessary
cleanup on device close.
While there also make the device eternal.
Sponsored by: Citrix Systems R&D
Reported and Tested by: thompsa
MFC after: 2 weeks
