to map, and technically this isn't allowed.
Functionally, it works OK (at least on x86) to call bus_dmamap_load with
a NULL data pointer and zero length, so this is primarily for correctness
and consistency with other drivers.
While here, remove check in isci_io_request_construct for nseg==0.
Previously, bus_dmamap_load would pass nseg==1, even for case where
buffer is NULL and length = 0, which allowed CAM_DIR_NONE CCBs
to get processed. This check is not correct though, and needed to be
removed both for the changes elsewhere in this patch, as well as jeff's
preliminary bus_dmamap_load_ccb patch (which uncovered all of this in
the first place).
MFC after: 3 days
- Deembed scope id in L3 address in in6_lltable_dump().
- Simplify scope id recovery in rtsock routines.
- Remove embedded scope id handling in ndp(8) and route(8) completely.
from the callwheel. Calculate the cc->cc_next before removing the
callout, otherwise the code followed the invalid tailq links. After
this, make softclock_call_cc() return void, since it always return
cc->cc_next, which is immediately available to the softclock()
anyway. This also allows to eliminate a label under #ifdef SMP.
Remove the assignment of cc->cc_next from callout_cc_del(), since the
function is called with the callout already removed from callwheel.
If cancelling the migration, also clear the CALLOUT_DFRMIGRATION flag.
Postpone the free of the timeout(9) allocated callouts after the
migration checks are done.
Add some more strict asserts about the state of the callout in
callout_call_cc().
Reviewed by: attilio
Reported and tested by: pho (previous version)
MFC after: 2 weeks
callout is started before kern_setitimer() acquires process mutex, but
looses a race and kern_setitimer() gets the process mutex before the
callout. Then, assuming that new specified struct itimerval has
it_interval zero, but it_value non-zero, the callout, after it starts
executing again, clears p->p_realtimer.it_value, but kern_setitimer()
already rescheduled the callout.
As the result of the race, both p_realtimer is zero, and the callout
is rescheduled. Then, in the exit1(), the exit code sees that it_value
is zero and does not even try to stop the callout. This allows the
struct proc to be reused and eventually the armed callout is
re-initialized. The consequence is the corrupted callwheel tailq.
Use process mutex to interlock the callout start, which fixes the race.
Reported and tested by: pho
Reviewed by: jhb
MFC after: 2 weeks
- Check V_deembed_scopeid before checking if sa_family == AF_INET6.
- Fix scope id handing in route(8)[2] and ifconfig(8).
Reported by: rpaulo[1], Mateusz Guzik[1], peter[2]
over the active list. The mount interlock is not enough to guarantee
the validity of the tailq link pointers. The __mnt_vnode_next_active()
and __mnt_vnode_first_active() active lists iterators helper functions
did not provided the neccessary stability for the list, allowing the
iterators to pick garbage.
This was uncovered after the r243599 made the active list iterators
non-nop.
Since a vnode interlock is before the vnode_free_list_mtx, obtain the
vnode ilock in the non-blocking manner when under vnode_free_list_mtx,
and restart iteration after the yield if the lock attempt failed.
Assert that a vnode found on the list is active, and assert that the
helpers return the vnode with interlock owned.
Reported and tested by: pho
MFC after: 1 week
thought I've decided its overkill,a simple tuneable for
each RX and TX limit, and then init sets the ring values
based on that, should be sufficient.
More importantly, fix a bug causing a panic, when changing
the define style to IXGBE_LEGACY_TX a taskqueue init was
inadvertently set #ifdef when it should be #ifndef.
I couldn't think of a way to maintain the hardware TXQ locks _and_ layer
on top of that per-TXQ software queuing and any other kind of fine-grained
locks (eg per-TID, or per-node locks.)
So for now, to facilitate some further code refactoring and development
as part of the final push to get software queue ps-poll and u-apsd handling
into this driver, just do away with them entirely.
I may eventually bring them back at some point, when it looks slightly more
architectually cleaner to do so. But as it stands at the present, it's
not really buying us much:
* in order to properly serialise things and not get bitten by scheduling
and locking interactions with things higher up in the stack, we need to
wrap the whole TX path in a long held lock. Otherwise we can end up
being pre-empted during frame handling, resulting in some out of order
frame handling between sequence number allocation and encryption handling
(ie, the seqno and the CCMP IV get out of sequence);
* .. so whilst that's the case, holding the lock for that long means that
we're acquiring and releasing the TXQ lock _inside_ that context;
* And we also acquire it per-frame during frame completion, but we currently
can't hold the lock for the duration of the TX completion as we need
to call net80211 layer things with the locks _unheld_ to avoid LOR.
* .. the other places were grab that lock are reset/flush, which don't happen
often.
My eventual aim is to change the TX path so all rejected frame transmissions
and all frame completions result in any ieee80211_free_node() calls to occur
outside of the TX lock; then I can cut back on the amount of locking that
goes on here.
There may be some LORs that occur when ieee80211_free_node() is called when
the TX queue path fails; I'll begin to address these in follow-up commits.
which dumps out the actual options being used by an NFS mount.
This will be used to implement a "-m" option for nfsstat(1).
Reviewed by: alfred
MFC after: 2 weeks
This brand of controllers expects that the number of
contexts specified in the input slot context points
to an active endpoint context, else it refuses to
operate.
- Ring the correct doorbell when streams mode is used.
- Wrap one or two long lines.
Tested by: Markus Pfeiffer (DragonFlyBSD)
MFC after: 1 week
Programming the low bits has a side-effect if unmasking the pin if it is
not disabled. So if an interrupt was pending then it would be delivered
with the correct new vector but to the incorrect old LAPIC.
This fix could be made clearer by preserving the mask bit while
programming the low bits and then explicitly resetting the mask bit
after all the programming is done.
Probability to trip over the fixed bug could be increased by bootverbose
because printing of the interrupt information in ioapic_assign_cpu
lengthened the time window during which an interrupt could arrive while
a pin is masked.
Reported by: Andreas Longwitz <longwitz@incore.de>
Tested by: Andreas Longwitz <longwitz@incore.de>
MFC after: 12 days
Also, make it explicit that V_XATTRDIR is not properly supported in gfs
code yet.
The bad code was plain incorrect: (a) it spoiled handling of v_usecount
reaching zero and (b) it leaked v_holdcnt.
The ugly code employs potentially unsafe locking tricks.
Ideally we should separate vnode lifecycle and gfs node lifecycle.
A gfs node should have its own reference count where its child nodes
should be accounted.
PR: kern/151111
Reviewed by: kib
MFC after: 13 days
... to avoid any races or inconsistencies.
This should fix a regression introduced in r243404.
Also, remove a stale comment that has not been true for quite a while
now.
Pointyhat to: avg
Teested by: trociny, emaste, dumbbell (earlier version)
MFC after: 1 week
src/sys/{bsm,security/audit}. There are a few tweaks to help with the
FreeBSD build environment that will be merged back to OpenBSM. No
significant functional changes appear on the kernel side.
Obtained from: TrustedBSD Project
Sponsored by: The FreeBSD Foundation (auditdistd)
enforcing the TXOP and TBTT limits:
* Frames which will overlap with TBTT will not TX;
* Frames which will exceed TXOP will be filtered.
This is not enabled by default; it's intended to be enabled by the
TDMA code on 802.11n capable chipsets.
the revamped sysctl code did not work, and needed a change. This
makes the limit get set at the time that all sysctl stats are
created and is actually more elegant imho anyway.
TX hot path by getting rid of index calculations and simply
managing pointers. Much of the creative code is due to my
coworker here at Intel, Alex Duyck, thanks Alex!
Also, this whole series of patches was given the critical
eye of Gleb Smirnoff and is all the better for it, thanks
Gleb!
- add a limit for both RX and TX, change the default to 256
- change the sysctl usage to be common, and now to be called
during init for each ring.
- the TX limit is not yet used, but the changes in the last
patch in this series uses the value.
- the motivation behind these changes is to improve data
locality in the final code.
- rxeof interface changes since it now gets limit from the
ring struct
Fix path handling for *at() syscalls.
Before the change directory descriptor was totally ignored,
so the relative path argument was appended to current working
directory path and not to the path provided by descriptor, thus
wrong paths were stored in audit logs.
Now that we use directory descriptor in vfs_lookup, move
AUDIT_ARG_UPATH1() and AUDIT_ARG_UPATH2() calls to the place where
we hold file descriptors table lock, so we are sure paths will
be resolved according to the same directory in audit record and
in actual operation.
Sponsored by: FreeBSD Foundation (auditdistd)
Reviewed by: rwatson
MFC after: 2 weeks
