be wrong but I couldn't find a way to make it work. In addition, the
number of TxGFP instruction does not match the firmware image size,
so I guess something was wrong when Adaptec generated the TxGFP
firmware from their DDK.
According to datasheet, normally, the first GFP instruction would be
opcode C, WaitForStartOfFrame, to synchronize checksumming with
incoming frame. But the first instruction in TxGFP firmware was
opcode 1, BrToImmIfTrue, so it could not process checksum correctly,
I guess. Checking for RxGFP firmware also indicates the first
instruction should be opcode C. Since the number of instructions in
TxGFP firmware lacks exactly one instruction, I prepended the opcode
C to TxGFP firmware image. With this change, the resulting image size
perfectly matches with the nummber of instructions and Tx checksum
offload seems to work without problems.
since the the command and data that is being built to be sent to or read
from the HW lives in the softc. Commands are later run via an_setdef etc.
In the ioctl path various references are kept to the data stored in
the softc so it needs to be protected. Almost think of the command
in the softc a global variable since it essentially is. Since locking
wasn't done in this type of context the commands would get corrupted.
Thanks to avatar@ for catching some lock issues and dhw@ for testing.
Things are a lot more stable except for the MPI-350 cards. My an(4)
remote laptop stays on the network now.
The driver should be changed so that it uses private memory that is passed
to the functions that talk to the card. Then only those functions would
really need to grab locks.
Reviewed by: avatar@
shortest possible chain of mbufs of m_defrag(9). What we want is
chains of mbufs that can be safely stored to a Tx descriptor which
can have up to STGE_MAXTXSEGS mbufs. The ethernet controller does
not need to align Tx buffers on 32bit boundary. So the use of
m_defrag(9) was waste of time.
problems when the DRM driver is loaded and the AIXGL extension is loaded
, the AIXGL driver requests a drm_close and this will cause the radeon
driver to fail while starting X windows.
PR: kern/114688
Submitted by: vehemens <vehemens at verizon dot net>
Prodded by: Robert Noland
Approved by: imp (mentor, a while ago already), anholt
MFC After: 1 week
- Track packet zone mbufs separately from other mbufs
- free packet zone buffers via m_free rather than trying to manage the refcount
as with clusters - its refcount and management seems to be "special"
but reread it from the device_t every time the device list is fetched.
Previously the device name in pciconf -l would not be updated when a driver
was unloaded or if a device was detached and attached to a different
driver.
MFC after: 1 week
PR: kern/104777
Submitted by: "Iasen Kostoff" tbyte | otel net
queues (which we call slices). The NIC will steer traffic into up to
hw.mxge.max_slices different receive rings based on a configurable
hash type (hw.mxge.rss_hash_type).
Currently the driver defaults to using a single slice, so the default
behavior is unchanged. Also, transmit from non-zero slices is
disabled currently.
spec:
- Use read/modify/write cycles to enable and disable the HPET instead of
writing 0 to reserved bits.
- Shutdown the HPET during suspend as encouraged by the spec.
- Fail to attach to an HPET with a period of zero.
MFC after: 1 week
PR: kern/119675 [3]
Reported by: Leo Bicknell | bicknell ufp.org
- Fix a bug introduced in 1.4.20 where speculative read by the processor in the
write-only doorbell region would cause a target-abort (as opposed to simply
returning random data). This could manifest itself as NMI or machine freeze
depending on how the BIOS/OS/chipset configuration handles target-abort.
- Add support for new revisions of -R cards (with AEL1002/AEL1010 xaui->xfi)
- Increase an internal timing (dispatch engine): fix possible spurious reset
(seen on very few cards).
- increase asserts for mbuf accounting
- track outstanding mbufs (maps very closely to leaked)
- actually only create one thread per port if !multiq
Oddly enough this fixes the use after free
- move txq_segs to stack in t3_encap
- add checks that pidx doesn't move pass cidx
- simplify mbuf free logic in collapse mbufs routine
- move cxgb_tx_common in to cxgb_multiq.c and rename to cxgb_tx
- move cxgb_tx_common dependencies
- further simplify cxgb_dequeue_packet for the non-multiqueue case
- only launch one service thread per port in the non-multiq case
- remove dead cleaning code from cxgb_sge.c
- simplify PIO case substantially in by returning directly from mbuf collapse
and just using m_copydata
- remove gratuitous m_gethdr in the rx path
- clarify freeing of mbufs in collapse
o Increased number of Rx/Tx descriptors to 256 for 8169 GigEs
because it's hard to push the hardware to the limit with default
64 descriptors.
TSO requires large number of Tx descriptors to pass a full sized
TCP segment(65535 bytes IP packet) to hardware. Previously it
consumed 32 Tx descriptors, assuming MCLBYTES DMA segment size,
to send the TCP segment which means re(4) couldn't queue more
than two full sized IP packets.
For 8139C+ it still uses 64 Rx/Tx descriptors due to its hardware
limitations. With this changes there are (very) small waste of
memory for 8139C+ users but I don't think it would affect 8139C+
users for most cases.
o Various bus_dma(9) fixes.
- The hardware supports DAC so allow 64bit DMA operations.
- Removed BUS_DMA_ALLOC_NOW flag.
- Increased DMA segment size to 4096 from MCLBYTES because TSO
consumes too many descriptors with MCLBYTES DMA segment size.
- Tx/Rx side bus_dmamap_load_mbuf_sg(9) support. With these
changes the code is more readable than previous one and got a
(slightly) better performance as it doesn't need to pass/
decode arguments to/from callback function.
- Removed unnecessary callback function re_dmamap_desc() and
nuked rl_dmaload_arg structure which was used in the callback.
- Additional protection for DMA map load failure. In case of
failure reuse current map instead of returning a bogus DMA
map.
- Deferred DMA map unloading/sync operation for maximum
performance until we really need to load new DMA map. If we
happen to reuse current map(e.g. input error) there is no need
to sync/unload/load again.
- The number of allowable Tx DMA segments for a mbuf chains are
now 32 instead of magic nseg value. If the number of available
Tx descriptors are short enough to send highly fragmented mbuf
chains an optimized re_defrag() is called to collapse mbuf
chains which is supposed to be much faster than m_defrag(9).
re_defrag() was borrowed from ath(4).
- Separated Rx/Tx DMA tag from a common DMA tag such that Rx DMA
tag correctly uses DMA maps that were created with DMA alignment
restriction(8bytes alignments). Tx DMA tag does not have such
alignment limitation.
- Added additional sanity checks for DMA ring map load failure.
- Added additional spare Rx DMA map for graceful handling of Rx
DMA map load failure.
- Fixed misused bus_dmamap_sync(9) and added missing
bus_dmamap_sync(9) in re_encap()/re_txeof()/re_rxeof().
o Enabled TSO again as re(4) have reasonable number of Tx
descriptors.
o Don't touch DMA address of a Tx descriptor in re_txeof(). It's
not needed.
o Fix incorrect update of if_ierrors counter. For Rx buffer
shortage it should update if_qdrops as the buffer is reused.
o Added checks for unsupported H/W revisions and return ENXIO for
these hardwares. This is required to remove resource allocation
code in re_probe as other drivers do in device probe routine.
o Modified descriptor index manipulation macros as it's now possible
to have different number of descriptors for Rx/Tx.
o In re_start, to save a lock operation, use IFQ_DRV_IS_EMPTY before
trying to invoke IFQ_DRV_DEQUEUE. Also don't blindly call re_encap
since we already know the number of available Tx descriptors in
advance.
o Removed RL_TX_DESC_THLD which was used to reserve RL_TX_DESC_THLD
descriptors in Tx path. There is no such a limitation mentioned in
8139C+/8169/8110/8168/8101/8111 datasheet and it seems to work ok
without reserving RL_TX_DESC_THLD descriptors.
o Fix a comment for RL_GTXSTART. The register is 8bits register.
o Added comments for 8169/8139C+ hardware restrictions on descriptors.
o Removed forward declaration for "struct rl_softc", it's not needed.
o Added a new structure rl_txdesc for Tx descriptor managements and
a structure rl_rxdesc for Rx descriptor managements.
o Removed unused member variable rl_intlock in driver softc. There are
still several unused member variables which are supposed to be used
to access hardware statistics counters. But it seems that accessing
hardware counters were not implemented yet.
- Turn on WOL bits in suspend/shutdown method.
- WOL is disabled in resume routine as WOL can interfere normal
Rx operation.
- Move stge_reset() to stge_init_locked() as resetting hardware
clears configured Rx information which in turn results in
non-working Rx module after suspend/shutdown operation.
conjuction with 'thread' argument passing which is always curthread.
Remove the unuseful extra-argument and pass explicitly curthread to lower
layer functions, when necessary.
KPI results broken by this change, which should affect several ports, so
version bumping and manpage update will be further committed.
Tested by: kris, pho, Diego Sardina <siarodx at gmail dot com>
zone code. The GPE handler method (i.e. _L00) generates various Notify
events that need to be run to completion before the GPE is re-enabled.
In ACPI-CA, we queue an asynch callback at the same priority as a Notify
so that it will only run after all Notify handlers have completed. The
callback re-enables the GPE afterwards. We also changed the priority of
Notifies to be the same as GPEs, given the possibility that another GPE
could arrive before the Notifies have completed and we don't want it to
get queued ahead of the rest.
The ACPI-CA change was submitted by Alexey Starikovskiy (SUSE) and will
appear in a later release. Special thanks to him for helping track this
bug down.
MFC after: 1 week
Tested by: jhb, Yousif Hassan <yousif / alumni.jmu.edu>
a panic race on module unload. The wakeup() is internal to
kproc_exit/kthread_exit. The correct fix is to fix the msleep() in
detach to sleep on fdc->fdc_thread instead of &fdc->fdc_thread.
Noted and reviewed by: jhb
Pointy hat to: kib
MFC after: 1 week
Wakeup the thread doing the fdc_detach() when the fdc worker thread exits [1].
Write access to the write-protected floppy shall call device_unbusy() to
pair the device_busy() in the fd_access() [2].
PR: 116537 [1], 116539 [2]
MFC after: 1 week
rspq lock. Not doing so was causing us to skip re-enabling the interrupt.
- remove duplicate credits sysctl
- add support for dumping hardware context of the txq
- decrement budget_left when we break out of the process_responses loop
interrupt handlers for child devices by adding a dummy handler that is
always present so that the underlying interrupt thread is always around
avoiding panics from stray interrupts.
MFC after: 3 days
