- Implement proper combined mode decoding for Intel controllers to properly
identify SATA and PATA channels and associate ATA channels with SATA ports.
This fixes wrong reporting and in some cases hard resets to wrong SATA ports.
- Improve SATA registers support to handle hot-plug events and potentially
interface errors. For ICH5/6300ESB chipsets these registers accessible via
PCI config space. For later ones they may be accessible via PCI BAR(5).
- For controllers not generating interrupts on hot-plug events, implement
periodic status polling. Use it to detect hot-plug on Intel and VIA
controllers. Same probably could also be used for Serverworks and SIS.
K2 SATA controllers. The chip's status register must be read first, and
as a long, for other registers to be correctly updated after a command, and
this includes the command sequence in device detection as well as the
previously handled case after interrupts. While here, clean up some
previous hacks related to this controller.
Reported by: many
Reviewed by: mav
MFC after: 3 weeks
response to DMA activate FIS under certain circumstances. This is
recommended fix from chip datasheet. If triggered, this bug most likely
cause write command timeout.
MFC after: 2 weeks
value 0xff. On hot-plug this value confuses ata_generic_reset() device
presence detection logic. As soon as we already know drive presence from
SATA hard reset, hint ata_generic_reset() to wait for device signature
until success or full timeout.
corruption bug where if an ATA command is issued before DMA is started,
data will become available to the controller before it knows what to do
with it. This results in either data corruption or a controller crash.
This patch remedies the problem by adopting the workaround employed
by Linux and Darwin: starting the DMA engine prior to sending the ATA
command.
Observer on: Xserve G5
Reviewed by: mav
MFC after: 1 week
fix. On Apple OpenPICs, the low/high bit of the interrupt sense is only
respected for interrupt 0. We currently erroneously program all OpenPIC
interrupts level high instead of level low by default, which only matters
for some G5 systems where the SATA controllers use IRQ 0.
This change is a quick fix that will be reverted once the effect of
changing the default interrupt sense on embedded systems is known.
MFC after: 3 days
Limit early revisions from 6Gb/s to 3Gb/s by default, or they negotiate
only 1.5Gbps, when 3Gb/s devices connected.
Add dummy driver for PATA part of these controllers, preventing generic
driver attach them. It causes system freeze when SATA controller used after
PATA was touched.
- These revisions no longer have cable detection capability.
- The UDMA support bit of register 0x4b has been dropped without an
replacement.
- According to Linux it's crucial for working ATAPI DMA support to
also set the reserved bit 1 of regsiter 0x53 with these revisions.
MFC after: 1 week
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
Binary divider value 10 specified in datasheet is not a hex 0x10.
UDMA2 should be 33/2 instead of 66/4, which is documented as reverved,
UDMA4 should be 66/2 instead of 66/4, which is definitely wrong.
and Marvell handled. Instead of trying to attach two different drivers to
single device, wrapping each call, make one of them (atajmicron, atamarvell)
attach do device solely, but create child device for AHCI driver,
passing it all required resources. It is quite easy, as none of
resources are shared, except IRQ.
As result, it:
- makes drivers operation more independent and straitforward,
- allows to use new ahci(4) driver with such devices, adding support for
new features, such as PMP and NCQ, same time keeping legacy PATA support,
- will allow to just drop old ataahci driver, when it's time come.
These controllers provide combination of AHCI for SATA and legacy
PCI ATA for PATA. Use same solution as used for JMicron controllers.
Add IDs of Marvell 88SX6102, 88SX6111. 88SX6141 alike controllers
- Remove most of direct relations between ATA(4) peripherial and controller
levels. It makes logic more transparent and is a mandatory step to wrap
ATA(4) controller level into ATA-native CAM SIM.
- Tune AHCI and SATA2 SiI drivers memory allocation a bit to allow bigger
I/O transaction sizes without additional cost.
and progif is evil. It doesn't work reliably[1] and we should honor BIOS
configuration by the user.
- If the SATA controller is enbled but combined mode is disabled, mask off
the emulated IDE channel on the legacy IDE controller.
Pointed out by: mav[1]
the work area was totally unsynchronized which means this driver only
had a chance of working on x86 when no bounce buffers were involved,
which isn't that likely given that support for 64-bit DMA is currently
broken throughout ata(4).
- Add necessary little-endian conversion of accesses to the work area,
making this driver work on big-endian hosts. While at it, use the
alignment-agnostic byte order encoders in order to be on the safe side.
- Clear the reserved member of the SG list entries in order to be on the
safe side. [1]
Submitted by: yongari [1]
Reviewed by: yongari
MFC after: 3 days
MAXPHYS. Current ataahci driver memory allocation scheme includes only
64 items in DMA S/G table, and so not guarantied to support transactions
with more then 252K data.
Approved by: re (kensmith)
MFC after: 2 weeks
routine and save the resources using a chipset-data structure. Use these
preallocated resources to setup resources for the SATA channels to avoid
asking the PCI bus to allocate the same BAR multiple times.
Tested by: bms
MFC after: 1 week
chipset-specific code to attach chipset-specific data.
- Use chipset-specific data in the acard and promise chipsets rather than
changing the ivars of ATA PCI devices. ivars are reserved for use by the
parent bus driver and are _not_ available for use by devices directly.
This fixes a panic during sysctl -a with certain Promise controllers with
ACPI enabled.
Reviewed by: mav
Tested by: Magnus Kling (kingfon @ gmail) (on 7)
MFC after: 3 days
Feature is controlled by hint.ata.X.pm_level tunable:
0 - PM disabled, old behaviour, default.
1 - device is allowed to initiate PM state change, host is passive.
2 - host initiates PARTIAL state transition every time port is idle.
3 - host initiates SLUMBER state transition every time port is idle.
PARTIAL state has up to 100us (50us for me) wakeup latency, but for my
ICH8M saves 0.5W of power per drive. SLUMBER state has up to 10ms (3.5ms
for me) wakeup latency, but saves 0.8W of power.
Modes 2 and 3 are implemented only for AHCI driver now.
Interface power management is incompatible with device presence detection
(host receives no signal from drive, so unable to monitor it), so later is
disabled when PM is used.
controllers may be configured as legacy IDE mode by modifying subclass and
progif without actually changing PCI device IDs. Instead of complicating
code, we always force AHCI mode while probing. Also we restore AHCI mode
while resuming per ATI/AMD register programming/requirement guides.
- Fix SB700/800 "combined" mode. Unlike SB600, this PATA controller can
combine two SATA ports and emulate one PATA channel as primary or secondary
depending on BIOS configuration. When the combined mode is disabled, this
channel disappears and it works just like SB600 PATA controller, however.
- Add more PCI device IDs for SB700/800 and adjust device descriptions.
SB800 shares the same PCI device IDs and added two more SATA IDs.
the ATA status register with a 4-byte read request. This updates it, and
subsequent 1-byte reads will return the correct result.
This commit adds a hack to do this, which is currently ifdef'd powerpc,
although Linux and Darwin do this unconditionally on all platforms.
Add ch_suspend/ch_resume methods for PCI controllers and implement them
for AHCI. Refactor AHCI channel initialization according to it.
Fix Port Multipliers operation. It is far from perfect yet, but works now.
Tested with JMicron JMB363 AHCI + SiI 3726 PMP pair.
Previous version was also tested with SiI 4726 PMP.
Hardware sponsored by: Vitsch Electronics / VEHosting.nl
ready status. Most of controllers managed to issue coommand and set BUSY
bit almost simultaneously, before we will read it, but at least JMicron JMB363
don't. Ignore timeout errors to keep old behavior when error there was
impossible.
For me this fixes timeout errors on the first command after channel attach
or reinit. Boot in my case is not affected, as there is much time passing
between reset and next command giving reset time to complete.
done in other places. Until we have no support for command queueing we have
no any benefit from FBS, while enabling it only here somehow leads to
"port not ready" errors on Intel 63XXESB2 controller.
Tested by: Larry Rosenman <ler AT lerctr.org>
- protect againtst recursions,
- add new devices detection using ata_identify().
Improve ata_identify():
- do not add duplicate device if device already exist.
Rework SATA hot-plug events handling. Instead of unsafe duplicate
implementation use common ata_reinit() to handle all state changes.
All together this gives quite stable and robust cold- and hot-plug operation,
invariant to false, lost and duplicate events.
ATA specification declares minimal reset time of 5us. SATA keeps it, but
requires devices to handle commands transmitted even one by one without
any gap.
as ATA RAID, but generic ATAPCI driver unable to detect drives there. AHCI
driver reported to handle them fine. Linux does the same.
Submitted by: Andrey V. Elsukov on stable@
join allocate() and dmainit() atapci subdriver's channel initialization
methods into single ch_attach() method.
As opposite to ch_attach() add new ch_detach() method to deallocate/disable
channel.
to not allocate them after the recent ata channels enumeration changes.
It allows to save some resources, not bother user with unexisting hardware
and not check unimplemented ports status on every interrupt.
