The new load_ma implementation can cause dereferences when used with
certain drivers, back it out until the reason is found:
Fatal trap 12: page fault while in kernel mode
cpuid = 11; apic id = 03
fault virtual address = 0x30
fault code = supervisor read data, page not present
instruction pointer = 0x20:0xffffffff808a2d22
stack pointer = 0x28:0xfffffe07cc737710
frame pointer = 0x28:0xfffffe07cc737790
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, long 1, def32 0, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 13 (g_down)
trap number = 12
panic: page fault
cpuid = 11
KDB: stack backtrace:
#0 0xffffffff80641647 at kdb_backtrace+0x67
#1 0xffffffff80606762 at vpanic+0x182
#2 0xffffffff806067e3 at panic+0x43
#3 0xffffffff8084eef1 at trap_fatal+0x351
#4 0xffffffff8084f0e4 at trap_pfault+0x1e4
#5 0xffffffff8084e82f at trap+0x4bf
#6 0xffffffff80830d57 at calltrap+0x8
#7 0xffffffff8063beab at _bus_dmamap_load_ccb+0x1fb
#8 0xffffffff8063bc51 at bus_dmamap_load_ccb+0x91
#9 0xffffffff8042dcad at ata_dmaload+0x11d
#10 0xffffffff8042df7e at ata_begin_transaction+0x7e
#11 0xffffffff8042c18e at ataaction+0x9ce
#12 0xffffffff802a220f at xpt_run_devq+0x5bf
#13 0xffffffff802a17ad at xpt_action_default+0x94d
#14 0xffffffff802c0024 at adastart+0x8b4
#15 0xffffffff802a2e93 at xpt_run_allocq+0x193
#16 0xffffffff802c0735 at adastrategy+0xf5
#17 0xffffffff80554206 at g_disk_start+0x426
Uptime: 2m29s
Add a new flag for DMA operations, DMA_NO_WAIT. It behaves much like
other NOWAIT flags -- if queueing an operation would sleep, abort and
return NULL instead.
When growing the internal descriptor ring, the memory allocation is
performed outside of all locks. A lock-protected flag is used to avoid
duplicated work. Threads that cannot sleep and attempt to queue
operations when the descriptor ring is full allocate a larger ring with
M_NOWAIT, or bail if that fails.
ioat_reserve_space() could become an external API if is important to
callers that they have room for a sequence of operations, or that those
operations succeed each other directly in the hardware ring.
This patch splits the internal head index (->head) from the hardware's
head-of-chain (DMACOUNT) register (->hw_head). In the future, for
simplicity's sake, we could drop the 'ring' array entirely and just use
a linked list (with head and tail pointers rather than indices).
Suggested by: Witness
Sponsored by: EMC / Isilon Storage Division
Assertion used here was invalid. If current thread helds any of locks,
we never want to recurse on them.
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3903
Add e6000sw driver supporting Marvell 88E6352, 88E6172, 88E6176 switches.
It needs to be attached to mdio interface, exporting SMI access
functionality. e6000sw supports port-based VLAN configuration, per-port
media changing, accessing PHY and switch registers.
e6000sw attaches miibuses and PHY drivers as children. Instead of typical
tick as callout, kthread-based tick is used. This combined with SX locks
allows MDIO read/write calls to sleep. It is expected, because this
hardware requires long delays in SMI read/write procedures, which can not
be handled by busy-waiting.
Reviewed by: adrian
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3902
This commit introduces support for etherswitch devices that utilize SMI as
a way of accessing its registers. SMI register is located in address space
of mge -- access to it was exported through MDIO interface.
Attachment functions were enhanced so as to ensure proper initialisation
in both cases: 1) PHYs attached directly to mge, 2) PHYs attached to
switch device and switch attached to mge. Attachment of etherswitch device
depends on dts entry with compatible="mrvl,sw" property. If none is found,
typical PHY attachment procedure follows.
In case of switch attached, PHYs' status and configuration is accessible
via etherswitchcfg, and ifconfig shows always-up, non-configurable mge
interfaces.
Due to the fact that there may be simultaneous accessess to SMI
registers (e.g. from PHY attached to one of mge instances and switch
to the other), SMI access interlock was added. It is SX lock,
because sleep ability is necessary -- busy-waiting would result
in poor performance due to long delays required by hardware.
Underlying switch driver is obliged to use sleepable locks as well.
Reviewed by: adrian
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3900
We need to reset the chancmp and chainaddr MMIO registers to bring the
device back to a working state.
Name the chanerr bits while we're here.
Sponsored by: EMC / Isilon Storage Division
We only need to borrow a mutex for the drain sleep and the 0->1
transition, so just reuse an existing one for now.
The wchan is arbitrary. Using refcount itself would have required
__DEVOLATILE(), so use the lock's address instead.
Different uses are tagged by kind, although we only do anything with
that information in INVARIANTS builds.
Sponsored by: EMC / Isilon Storage Division
Callers should have acquired this lock when they invoked ioat_acquire()
before issuing operations. Assert it is held.
Sponsored by: EMC / Isilon Storage Division
This is still the worst possible way to allocate memory if it will ever
be under pressure, but at least it won't deadlock.
Suggested by: WITNESS
Sponsored by: EMC / Isilon Storage Division
Pull out the timer callout delay into IOAT_INTR_TIMO and shorten it
considerably (5s -> 100ms). Single operations do not take 5-10 seconds
and when interrupts aren't working, waiting 100ms sucks a lot less than
5s.
Sponsored by: EMC / Isilon Storage Division
Now 24xx and above chips support full 8-byte LUN address space.
Older FC chips may support up to 16K LUNs when firmware allows.
Tested in both initiator and target modes for 23xx, 24xx and 25xx.
This change allows to decode respective functions in isp(4) in target mode
and pass them through CAM to CTL. Unfortunately neither CAM nor isp(4)
support returning response info for those task management functions now.
On the other side I just have no initiator to test this functionality.
Using unmapped IO is really beneficial when running inside of a VM,
since it avoids IPIs to other vCPUs in order to invalidate the
mappings.
This patch adds unmapped IO support to blkfront. The following tests
results have been obtained when running on a Xen host without HAP:
PVHVM
3165.84 real 6354.17 user 4483.32 sys
PVHVM with unmapped IO
2099.46 real 4624.52 user 2967.38 sys
This is because when running using shadow page tables TLB flushes and
range invalidations are much more expensive, so using unmapped IO
provides a very important performance boost.
Sponsored by: Citrix Systems R&D
MFC after: 2 weeks
X-MFC-with: r289834
FC port database code already notifies CAM about all devices. Additional
full scan is just a waste of time, that by definition won't find anything
that is not present in port database.
registers (they are used for different purposes).
- Wrap R92C_MSR modifications into urtwn_set_mode().
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D3838
* Add a comment about the parameters I should support, stolen shamelessly
from iwn(4);
* Implement the rate bit for the raw transmit path;
* Print out the host-order versions of each of the transmit bits, so
I have a hope in heck of debugging why things are going wrong.
This still doesn't fix 5GHz in the office but that's likely due to a lot
of other configuration parameters being 2GHz-specific. That'll come next.
Tested:
* AR9170 + AR9103 (2/5GHz) 2x2, 5GHz association
Replace custom Linux-like logging with a thin shim around
device_printf(), when the softc is available.
In ioat_test, shim around printf(9) instead.
Sponsored by: EMC / Isilon Storage Division
This should export all of the same information as the Linux ntb_hw_intel
debugfs info file, but with a bit more structure, in the sysctl tree
rooted at 'dev.ntb_hw.<N>.debug_info'.
Raw registers are marked as OPAQUE because reading them on some hardware
revisions may cause a hard lockup (NTB errata). They can be read with
'sysctl -x dev.ntb_hw.<N>.debug_info.registers'. On Xeon platforms,
some additional registers are available under 'registers.xeon_stats' and
'registers.xeon_hw_err'. They are exported as big-endian values so that
the 'sysctl -x' output is legible.
Shrink the feature mask to 32 bits so we can use the %b formatter in
'debug_info.features'.
Sponsored by: EMC / Isilon Storage Division
Don't run the selftest until after we've enabled bus mastering, or the
DMA engine can't copy anything for our test.
Create the ioat_test device on attach, if so tuned. Destroy the
ioat_test device on teardown.
Replace deprecated 'CALLOUT_MPSAFE' with correct '1' in callout_init().
Sponsored by: EMC / Isilon Storage Division
The test logic now preallocates memory before running the test.
The buffer size is now configurable. Post-copy verification is
configurable. The number of copies to chain into one transaction (one
interrupt) is configurable.
A 'duration' mode is added, which repeats the test until the duration
has elapsed, reporting the B/s and transactions completed.
ioatcontrol.8 has been updated to document the new arguments.
Initial limits (on this particular Broadwell-DE) (and when the
interrupts are working) seem to be: 256 interrupts/sec or ~6 GB/s,
whichever limit is more restrictive.
Unfortunately, it seems the interrupt-reset handling on Broadwell isn't
working as intended. That will be fixed in a later commit.
Sponsored by: EMC / Isilon Storage Division
The FDT bindings for eeprom parts don't include any metadata about the
device other than the part name encoded in the compatible property.
Instead, a driver is required to have a compiled-in table of information
about the various parts (page size, device capacity, addressing scheme). So
much for FDT being an abstract description of hardware characteristics, huh?
In addition to the FDT-specific changes, this also switches to using the
newer iicbus_transfer_excl() mechanism which holds bus ownership for the
duration of the transfer. Previously this code held the bus across all
the transfers needed to complete the user's IO request, which could be
up to 128KB of data which might occupy the bus for 10-20 seconds. Now the
bus will be released and re-aquired between every page-sized (8-256 byte)
transfer, making this driver a much nicer citizen on the i2c bus.
The hint-based configuration mechanism is still in place for non-FDT systems.
Michal Meloun contributed some of the code for these changes.
while holding exclusive ownership of the bus. This is the routine most
slave drivers should use unless they have a need to acquire and hold the
bus across a series of related operations that involves multiple transfers.
various reasons while executing user commands. After these commands are
completed, the pages backing the relocation regions are unheld.
Since relocation regions do not have to be page aligned, the code in
validate_exec_list() allocates 2 extra page pointers in the array of
held pages populated by vm_fault_quick_hold_pages(). However, the cleanup
code that unheld the pages always assumed that only the buffer size /
PAGE_SIZE pages were used. This meant that non-page aligned buffers would
not unheld the last 1 or 2 pages in the list. Fix this by saving the
number of held pages returned by vm_fault_quick_hold_pages() for each
relocation region and using this count during cleanup.
Reviewed by: dumbbell, kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D3965
represented in 7-bits format in DT files, but system expect it in 8-bit
format. Also, fix two drivers that locally hack around this bug.
Submitted by: Michal Meloun <meloun@miracle.cz>
r289587 broke LINT-NOIP kernels because the lro and queued local variables
are defined but not used. Add preprocessor guards around them.
Reported by: emaste
Sponsored by: Citrix Systems R&D
xen/hypervisor.h:
- Remove unused helpers: MULTI_update_va_mapping, is_initial_xendomain,
is_running_on_xen
- Remove unused define CONFIG_X86_PAE
- Remove unused variable xen_start_info: note that it's used inpcifront
which is not built at all
- Remove forward declaration of HYPERVISOR_crash
xen/xen-os.h:
- Remove unused define CONFIG_X86_PAE
- Drop unused helpers: test_and_clear_bit, clear_bit,
force_evtchn_callback
- Implement a generic version (based on ofed/include/linux/bitops.h) of
set_bit and test_bit and prefix them by xen_ to avoid any use by other
code than Xen. Note that It would be worth to investigate a generic
implementation in FreeBSD.
- Replace barrier() by __compiler_membar()
- Replace cpu_relax() by cpu_spinwait(): it's exactly the same as rep;nop
= pause
xen/xen_intr.h:
- Move the prototype of xen_intr_handle_upcall in it: Use by all the
platform
x86/xen/xen_intr.c:
- Use BITSET* for the enabledbits: Avoid to use custom helpers
- test_bit/set_bit has been renamed to xen_test_bit/xen_set_bit
- Don't export the variable xen_intr_pcpu
dev/xen/blkback/blkback.c:
- Fix the string format when XBB_DEBUG is enabled: host_addr is typed
uint64_t
dev/xen/balloon/balloon.c:
- Remove set but not used variable
- Use the correct type for frame_list: xen_pfn_t represents the frame
number on any architecture
dev/xen/control/control.c:
- Return BUS_PROBE_WILDCARD in xs_probe: Returning 0 in a probe callback
means the driver can handle this device. If by any chance xenstore is the
first driver, every new device with the driver is unset will use
xenstore.
dev/xen/grant-table/grant_table.c:
- Remove unused cmpxchg
- Drop unused include opt_pmap.h: Doesn't exist on ARM64 and it doesn't
contain anything required for the code on x86
dev/xen/netfront/netfront.c:
- Use the correct type for rx_pfn_array: xen_pfn_t represents the frame
number on any architecture
dev/xen/netback/netback.c:
- Use the correct type for gmfn: xen_pfn_t represents the frame number on
any architecture
dev/xen/xenstore/xenstore.c:
- Return BUS_PROBE_WILDCARD in xctrl_probe: Returning 0 in a probe callback
means the driver can handle this device. If by any chance xenstore is the
first driver, every new device with the driver is unset will use xenstore.
Note that with the changes, x86/include/xen/xen-os.h doesn't contain anymore
arch-specific code. Although, a new series will add some helpers that differ
between x86 and ARM64, so I've kept the headers for now.
Submitted by: Julien Grall <julien.grall@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3921
Sponsored by: Citrix Systems R&D
I messed up when doing the reset_vlans method - setting vid[0] = 1 here
was making it 'hidden' from configuration (as it needed ETHERSWITCH_VID_VALID
as well) and so there was no way to configure vlangroup0.
In per-port VLAN mode, vlangroup0 is for the CPU port (port0).
Now, it normally wouldn't really matter - the CPU port thus sees
all other ports. However there are two CPU ports on the AR8327 and
so port0 (arge0) was seeing all traffic on port6 (arge1).
If you thus tried to use arge1/port6 for anything (eg a WAN port)
in a bridge group then things would very upset very quickly.
Whilst here, add a comment to remind myself that yes, it'd be nice
if we could specify a boot-time switch config.
Tested:
* AP135 reference platform w/ AR8327N switch
If the bus is detached and deleted by a call to device_delete_child() or
device_delete_children() on a device higher in the tree, I²C children
were already detached and deleted. So the device_t pointer stored in sc
points to freed memory: we must not try to delete it again.
By using device_delete_children(), we let subr_bus.c figure out if there
are children to take care of.
While here, make sure iicbus_detach() and iicoc_detach() call
device_delete_children() too, to be safe.
Reviewed by: jhb, imp
Approved by: jhb, imp
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D3926
Add ntb_q_idx_t so it is more clear which struct members are of the same
type (some bogus uint64_ts snuck in that should have been unsigned int).
Add tx_err_no_buf and s/ENOMEM/EBUSY/ in tx_enqueue to match Linux.
Sponsored by: EMC / Isilon Storage Division
A plain 32 bit integer will overflow for values over 4GiB.
Change the plain integer size to the appropriate size type in
ntb_set_mw. Change the type of the size parameter and two local
variables used for size.
Even if there is no overflow, a size of zero is invalid here.
Authored by: Allen Hubbe
Reported by: Juyoung Jung
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
It was possible for a synchronous update of the RX index in the error
case to get ahead of the asynchronous RX index update in the normal
case. Change the RX processing to preserve an RX completion order.
There were two error cases. First, if a buffer is not present to
receive data, there would be no queue entry to preserve the RX
completion order. Instead of dropping the RX frame, leave the RX frame
in the ring. Schedule RX processing when RX entries are enqueued, in
case there are RX frames waiting in the ring to be received.
Second, if a buffer is too small to receive data, drop the frame in the
ring, mark the RX entry as done, and indicate the error in the RX entry
length. Check for a negative length in the receive callback in
ntb_netdev, and count occurrences as rx_length_errors.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Mechanically replace "SOC" with "ATOM" to match Linux. No functional
change. Original Linux commit log follows:
Instead of using the platform code names, use the correct platform names
to identify the respective Intel NTB hardware.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Prints driver name to indicate what is being loaded.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Benchmarking showed a significant performance increase with the MTU size
to 64k instead of 16k. Change the driver default to 64k.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Throw away the result of the peer SPAD read. The peer will write our
local SPAD and we need to keep the locally read SPAD value to check if
the remote side is up.
Sponsored by: EMC / Isilon Storage Division
Add module parameters for the addresses to be used in B2B topology.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Reset the link stats when the link goes down. In particular, the TX and
RX index and count must be reset, or else the TX side will be sending
packets to the RX side where the RX side is not expecting them. Reset
all the stats, to be consistent.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
We skip actually bringing up Rootport/Transparent configurations, so
most of this doesn't apply. Original Linux commit log:
Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen. Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
It is just a trivial wrapper around ntb_mw_set_trans().
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The failure path for allocating rx grant refs should not try to free tx
grant refs because tx grant refs were allocated after that. Also fix the
error path for xen_net_read_mac.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3891
Sponsored by: Citrix Systems R&D
This is redundant because ether_ifattach will set that field.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3918
Sponsored by: Citrix Systems R&D
We're way beyond FreeBSD 7 at this point.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3892
Sponsored by: Citrix Systems R&D
Multiqueue feature will make the number of queues dynamic, so XN_LOCK_INIT
won't be that useful. Remove the macro and call mtx_init directly.
XN_LOCK_DESTROY is just dead code.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3890
Sponsored by: Citrix Systems R&D
Rename it with netfront_ prefix and purge a bunch of unused fields.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3889
Sponsored by: Citrix Systems R&D
Currently neither Linux nor FreeBSD netback supports page flipping. NetBSD
still supports that. It is not sure how many people actually use page
flipping, but page flipping is supposed to be slower than copying nowadays.
It will also shatter frontend / backend address space.
Overall this feature is more of a burden than a benefit.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3888
Sponsored by: Citrix Systems R&D
- Define the kref structure identical to the one found in Linux.
- Update clients referring inside the kref structure.
- Implement kref_sub() for FreeBSD.
Reviewed by: np @
Sponsored by: Mellanox Technologies
* Use the correct malloc type for node allocation - M_80211_NODE - so
the default node free method in net80211 will work correctly.
* Fix otus_node_alloc() to suit FreeBSD's net80211.
* .. and actually call otus_node_alloc() so there's space for the
per-node tx statistics. Otherwise, well, it will be scribbling over
random memory.
Tested:
* AR9170, STA mode
The monitor mode stuff is from the openbsd driver, but it doesn't
100% work. It doesn't seem to get all frames for all BSSes.
However, it's enough to at start debugging things. That 0xffffffff
write is /I think/ the RX filter, but I am still not 100% sure about
it all.
Then, whilst here, use the lowest rate for EAPOL frames. This is just
generally a good thing to do.
This commit adds support for MDIO present in the ThunderX SoC.
From the FDT point of view it is compatible with "octeon-3860-mdio"
however only C22 mode is used.
The code also implements lmac_if interface functions.
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
- The driver consists of three main componens: PF, VF, BGX
- Requires appropriate entries in DTS and MDIO driver
- Supports only FDT configuration
- Multiple Tx queues and single Rx queue supported
- No RSS, HW checksum and TSO support
- No more than 8 queues per-IF (only one Queue Set per IF)
- HW statistics enabled
- Works in all available MAC modes (1,10,20,40G)
- Style converted to BSD according to style(9)
- The code brings lmac_if interface used by the BGX driver to
update its logical MACs state.
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
This import brings following components of the Linux driver:
- Thunder BGX (programmable MAC)
- Physical Function driver
- Virtual Function driver
- Headers
Revision: 1.0
Obtained from: Cavium
License information: Cavium provided these files under BSD license
This is the last e26a5843 patch. The general thrust of the rewrite was
to move more responsibility for Memory Window and Doorbell interrupt
management from the ntb_hw driver to if_ntb.
A number of APIs have been added, removed, or replaced. The old
DB callback mechanism has been excised. Instead, callers (if_ntb) are
responsible for configuring MWs and handling their interrupts more
directly.
This adds a tunable, hw.ntb.max_mw_size, allowing users to limit the
size of memory windows used by if_ntb (identical to the Linux modparam
of the same name).
Despite attempts to keep mechanical name changes to separate commits,
some have snuck in here. At least the driver should be much more
similar to the latest Linux one now -- making porting fixes easier.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
No functional change. Part of the huge rewrite (e26a5843).
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Move all Xeon secondary register setup to the setup_b2b_mw routine. We
use subroutines to make it a bit less wordy than the Linux version.
Adds a new tunable, 'hw.ntb.b2b_mw_share'. By default, it is off
(zero). If both sides enable it (any non-zero value), the NTB driver
attempts to use only half of a memory window for remote register MMIO
access.
This is still part of the large Linux rewrite (e26a5843).
Authored by: Allen Hubbe
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This Linux commit was more or less a rewrite. Unfortunately, the commit
log does not give a lot of context for the rewrite. I have tried to
faithfully follow the changes made upstream, including matching function
names where possible, while churning the FreeBSD driver as little as
possible.
This is the bulk of the rewrite. There are two groups of changes to
follow in separate commits: fleshing out the rest of the changes to
xeon_setup_b2b_mw(), and some changes to if_ntb.
Yes, this is a big patch (3 files changed, 416 insertions(+), 237
deletions(-)), but the Linux patch was 13 files changed, 2,589
additions(+) and 2,195 deletions(-).
Original Linux commit log:
Change ntb_hw_intel to use the new NTB hardware abstraction layer.
Split ntb_transport into its own driver. Change it to use the new NTB
hardware abstraction layer.
Authored by: Allen Hubbe
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Some interrupt-related function names changed to match Linux.
No functional change. Still part of the huge e26a5843 rewrite in Linux.
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
No functional change.
Still part of the huge e26a5843 rewrite. I'm trying to make it less of
a complete rewrite in the FreeBSD version of the driver. Still, it
helps if our names match Linux.
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
On the Haswell platform, a split BAR option to allow creation of 2 32bit
BARs (4 and 5) from the 64bit BAR 4. Adding support for this new option.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This is a follow-up to r289208: "Xeon Errata Workaround."
Add logic to support a variable number of memory windows and doorbell
callbacks. This was added to the Linux driver in the "Xeon Errata
Workaround" commit, but I skipped it because it didn't look neccessary
at the time. It is needed for future Haswell split-BAR support, so
bring it in now.
A new tunable was added for if_ntb, 'hw.ntb.max_num_clients'. By
default, it is set to zero -- infer the number of clients from the
number of memory windows available from the hardware. Any other
positive value can specify a different number of clients, limited by the
number of doorbell callbacks available (4 under MSI-X, or 15 (Xeon) or
34 (SoC) under legacy INTx).
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This patch adds support for the BCM57765[2] card reader function included in
Broadcom's BCM57766 ethernet/sd3.0 controller. This controller is commonly
found in laptops and Apple hardware (MBP, iMac, etc).
The BCM57765 chipset is almost fully compatible with the SD3.0 spec, but
does not support deriving a frequency below 781KHz from its default base
clock via the standard SD3.0-configured 10-bit clock divisor.
If such a divisor is set, card identification (which requires a 400KHz
clock frequency) will time out[1].
As a work-around, I've made use of an undocumented device-specific clock
control register to switch the controller to a 63MHz clock source when
targeting clock speeds below 781KHz; the clock source is likewise switched
back to the 200MHz clock when targeting speeds greater than 781KHz.
Additionally, this patch fixes a small sdhci_pci bug; the
sdhci_pci_softc->quirks flag was not copied to the sdhci_slot, resulting in
`quirk` behavior not being applied by sdhci.c.
[1] A number of Linux/FreeBSD users have noted that bringing up the chipsets'
associated ethernet interface will allow SD cards to enumerate (slowly).
This is a controller implementation side-effect triggered by the ethernet
driver's reading of the hardware statistics registers.
[2] This may also fix card detection when using the BCM57785 chipset, but I
don't have access to the BCM57785 chipset and can't verify.
I actually snagged some BCM57785 hardware recently (2012 Retina MacBook Pro)
and can confirm that this also fixes card enumeration with the BCM57785
chipset; with the patch, I can boot off of the internal sdcard reader.
PR: kern/203385
Submitted by: Landon Fuller <landon@landonf.org>
Pull out read of PPD and platform detection logic to new functions,
ntb_detect_xeon(), ntb_detect_soc(). No functional change -- mostly
this is just shuffling the code to more closely match the Linux driver.
Linux commit log:
To simplify some of the platform detection code. Move the platform
detection to a function to be called earlier.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The doorbell registers (and associated mask) are 16-bit on Xeon but
64-bit on SoC. Abstract IO access to doorbell registers with
'db_ioread' and 'db_iowrite' (names and idea borrowed from the dual
BSD/GPL Linux driver).
Sponsored by: EMC / Isilon Storage Division
Original Linux commit log:
The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The detection of an uneven number of queues on the given memory windows
was not correct. The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Remap MSI-X messages over available slots rather than falling back to
legacy INTx when fewer MSI-X slots are available than were requested.
N.B. the Linux driver does *not* do this.
To aid in testing, a tunable 'hw.ntb.force_remap_mode' has been added.
It defaults to off (0). When the tunable is enabled and sufficient
slots were available, the driver restricts the number of slots by one
and remaps the MSI-X messages over the remaining slots.
In case this is actually not okay (as I don't yet have access to this
hardware to test), a tunable 'hw.ntb.prefer_intx_to_remap' has been
added. It defaults to off (0). When the tunable is enabled and fewer
slots are available than requested, fall back to legacy INTx mode rather
than attempting to remap MSI-X messages.
Suggested by: jhb
Reviewed by: jhb (earlier version)
Sponsored by: EMC / Isilon Storage Division
Consumers that registered on this bit would never see a callback and it
is likely a mistake.
This does not affect if_ntb, which limits itself to a single doorbell
callback.
The names don't line up 100% with Linux. Our routines are named
ntb_setup_interrupts, ntb_setup_xeon_msix, ntb_setup_soc_msix, and
ntb_setup_legacy_interrupt. Linux SNB = FreeBSD Xeon; Linux BWD =
FreeBSD SOC. Original Linux commit log:
This is an cleanup effort to make ntb_setup_msix() more readable - use
ntb_setup_bwd_msix() to init MSI-Xs on BWD hardware and
ntb_setup_snb_msix() - on SNB hardware.
Function ntb_setup_snb_msix() also initializes MSI-Xs the way it should
has been done - looping pci_enable_msix() until success or failure.
Authored by: Alexander Gordeev
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Provide a better event interface between the client and transport.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
according to the Cortex-A8 TRM r3p2 section 3.2.49.
The A8 list differs from the "ARM-v7 common" list, given the A8
was an earlier model.
There is still more work to be done for other Cortex-Ax version as
andrew points out, but I am just trying to fix A8 for now for teaching.
MFC after: 2 weeks
Sponsored by: DARPA/AFRL
Obtained from: Cambridge/L41
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D3876
Enable Snoop from Primary to Secondary side on BAR23 and BAR45 on all
TLPs. Previously, Snoop was only enabled from Secondary to Primary
side. This can have a performance improvement on some workloads.
Also, make the code more obvious about how the link is being enabled.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Add a comment describing the necessary ordering of modifications to the
NTB Limit and Base registers.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
A WARN_ON is being hit in ntb_qp_link_work due to the NTB transport link
being down while the ntb qp link is still active. This is caused by the
transport link being brought down prior to the qp link worker thread
being terminated. To correct this, shutdown the qp's prior to bringing
the transport link down. Also, only call the qp worker thread if it is
in interrupt context, otherwise call the function directly.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The Xeon NTB-RP setup, the transparent side does not get a link up/down
interrupt. Since the presence of a NTB device on the transparent side
means that we have a NTB link up, we can work around the lack of an
interrupt by simply calling the link up function to notify the upper
layers.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Modifications to the 14th bit of the B2BDOORBELL register will not be
mirrored to the remote system due to a hardware issue. To get around
the issue, shrink the number of available doorbell bits by 1. The max
number of doorbells was being used as a way to referencing the Link
Doorbell bit. Since this would no longer work, the driver must now
explicitly reference that bit.
This does not affect the xeon_errata_workaround case, as it is not using
the b2bdoorbell register.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
NTB-RP is not a supported configuration on BWD hardware. Remove the
code attempting to set it up.
Authored by: Jon Mason
Obtained from: Linux (dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This commit does not actually add NTB-RP support. Mostly it serves to
shuffle code around to match the Linux driver. Original Linux commit
log follows:
Add support for Non-Transparent Bridge connected to a PCI-E Root Port on
the remote system (also known as NTB-RP mode). This allows for a NTB
enabled system to be connected to a non-NTB enabled system/slot.
Modifications to the registers and BARs/MWs on the Secondary side by the
remote system are reflected into registers on the Primary side for the
local system. Similarly, modifications of registers and BARs/MWs on
Primary side by the local system are reflected into registers on the
Secondary side for the Remote System. This allows communication between
the 2 sides via these registers and BARs/MWs.
Note: there is not a fix for the Xeon Errata (that was already worked
around in NTB-B2B mode) for NTB-RP mode. Due to this limitation, NTB-RP
will not work on the Secondary side with the Xeon Errata workaround
enabled. To get around this, disable the workaround via the
xeon_errata_workaround=0 modparm. However, this can cause the hang
described in the errata.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Many variable names in the NTB driver refer to the primary or secondary
side. However, these variables will be used to access the reverse case
when in NTB-RP mode. Make these names more generic in anticipation of
NTB-RP support.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The BWD NTB device will drop the link if an error is encountered on the
point-to-point PCI bridge. The link will stay down until all errors are
cleared and the link is re-established. On link down, check to see if
the error is detected, if so do the necessary housekeeping to try and
recover from the error and reestablish the link.
There is a potential race between the 2 NTB devices recovering at the
same time. If the times are synchronized, the link will not recover and
the driver will be stuck in this loop forever. Add a random interval to
the recovery time to prevent this race.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
There is a Xeon hardware errata related to writes to SDOORBELL or B2BDOORBELL
in conjunction with inbound access to NTB MMIO Space, which may hang the
system. To workaround this issue, use one of the memory windows to access the
interrupt and scratch pad registers on the remote system. This bypasses the
issue, but removes one of the memory windows from use by the transport. This
reduction of MWs necessitates adding some logic to determine the number of
available MWs.
Since some NTB usage methodologies may have unidirectional traffic, the ability
to disable the workaround via modparm has been added.
See BF113 in
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-c5500-c3500-spec-update.pdf
See BT119 in
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-e5-family-spec-update.pdf
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Due to ambiguous documentation, the USD/DSD identification is backward
when compared to the setting in BIOS. Correct the bits to match the
BIOS setting.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The NTB Xeon hardware has 16 scratch pad registers and 16 back-to-back
scratch pad registers. Correct the #define to represent this and update
the variable names to reflect their usage.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
This doesn't free the mbuf upon error; the driver ic_raw_xmit method is still
doing that.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3774
Move error handling into ieee80211_parent_xmitpkt() instead of spreading it
between functions.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3772
* Create ieee80211_free_mbuf() which frees a list of mbufs.
* Use it in the fragment transmit path and ath / uath transmit paths.
* Call it in xmit_pkt() if the transmission fails; otherwise fragments
may be leaked.
This should be a big no-op.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3769
The system will appear to lockup for long periods of time due to the NTB
driver spending too much time in memcpy. Avoid this by reducing the
number of packets that can be serviced on a given interrupt.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The ring logic of the NTB receive buffer/transmit memory window requires
there to be at least 2 payload sized allotments. For the minimal size
case, split the buffer into two and set the transport_mtu to the
appropriate size.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
If the NTB link toggles, the driver could stop receiving due to the
tx_index not being set to 0 on the transmitting size on a link-up event.
This is due to the driver expecting the incoming data to start at the
beginning of the receive buffer and not at a random place.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Each link-up will allocate a new NTB receive buffer when the NTB
properties are negotiated with the remote system. These allocations did
not check for existing buffers and thus did not free them. Now, the
driver will check for an existing buffer and free it if not of the
correct size, before trying to alloc a new one.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
64bit BAR sizes are permissible with an NTB device. To support them
various modifications and clean-ups were required, most significantly
using 2 32bit scratch pad registers for each BAR.
Also, modify the driver to allow more than 2 Memory Windows.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
->remote_rx_info and ->rx_info are struct ntb_rx_info pointers. If we
add sizeof(struct ntb_rx_info) then it goes too far.
Authored by: Dan Carpenter
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
This change fixes some amount of -Wsign-conversion and -Wconversion warnings
and sets correct sizes for some variables (as a result, some loop counters
were touched too).
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3763
This is roughly the iw_cxgbe equivalent of
be13b2dff8
-----------------
RDMA/cxgb4: Connect_request_upcall fixes
When processing an MPA Start Request, if the listening endpoint is
DEAD, then abort the connection.
If the IWCM returns an error, then we must abort the connection and
release resources. Also abort_connection() should not post a CLOSE
event, so clean that up too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
-----------------
Submitted by: Krishnamraju Eraparaju at chelsio dot com.
This was off because the net80211 aggregation code was using the same
state pointers for both fast frames and ampdu tx support which led to some
pretty unfortunate panic-y behaviour.
Now that net80211 doesn't panic, let's flip this back on.
It doesn't (yet) do the horrific sounding thing of A-MPDU aggregates
of fast frames; that'll come next. It's a pre-requisite to supporting
AMSDU + AMPDU anyway, which actually speeds things up quite considerably
(think packing lots of little ACK frames into a single AMSDU.)
Tested:
* QCA955x SoC, AP mode
* AR5416, STA mode
* AR9170, STA mode (with local fast frame patches)
these functions are thin wrappers around calling the hardware-layer driver,
but some of them do sanity checks and return an error. Since the hardware
layer can only return IIC_Exxxxx status values, the iicbus helper functions
must also adhere to that, so that drivers at higher layers can assume that
any non-zero status value is an IIC_Exxxx value that provides details about
what happened at the hardware layer (sometimes those details are important
for certain slave drivers).
errno values that are at least vaguely equivelent. Also add a new status
value, IIC_ERESOURCE, to indicate a failure to acquire memory or other
required resources to complete a transaction.
The IIC_Exxxxxx values are supposed to communicate low-level details of the
i2c transaction status between the lowest-layer hardware driver and
higher-layer bus protocol and device drivers for slave devices on the bus.
Most of those slave drivers just return all status values from the lower
layers directly to their callers, resulting in crazy error reporting from a
user's point of view (things like timeouts being reported as "no such
process"). Now there's a helper function to make it easier to start
cleaning up all those drivers.
Make it clearer what each one means in the comments that define them.
IIC_BUSBSY was used in many places to mean two different things, either
"someone else has reserved the bus so you have to wait until they're done"
or "the signal level on the bus was not in the state I expected before/after
issuing some command".
Now IIC_BUSERR is used consistantly to refer to protocol/signaling errors,
and IIC_BUSBSY refers to ownership/reservation of the bus.
perform a stop operation on the bus if there was an error, otherwise the
bus will remain hung forever. Consistantly use 'if (error != 0)' style in
the function.
The current Xen console driver is crashing very quickly when using it on
an ARM guest. This is because the console lock is recursive and it may
lead to recursion on the tty lock and/or corrupt the ring pointer.
Furthermore, the console lock is not always taken where it should be and has
to be released too early because of the way the console has been designed.
Over the years, code has been modified to support various new features but
the driver has not been reworked.
This new driver has been rewritten with the idea of only having a small set
of specific function to write either via the shared ring or the hypercall
interface.
Note that HVM support has been left aside for now because it requires
additional features which are not yet supported. A follow-up patch will be
sent with HVM guest support.
List of items that may be good to have but not mandatory:
- Avoid to flush for each character written when using the tty
- Support multiple consoles
Submitted by: Julien Grall <julien.grall@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3698
Sponsored by: Citrix Systems R&D
Use direct dispatch into the destination hardware ring instead of using
a staging queue.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3757
Pull the latest headers for Xen which allow us to add support for ARM and
use new features in FreeBSD.
This is a verbatim copy of the xen/include/public so every headers which
don't exits anymore in the Xen repositories have been dropped.
Note the interface version hasn't been bumped, it will be done in a
follow-up. Although, it requires fix in the code to get it compiled:
- sys/xen/xen_intr.h: evtchn_port_t is already defined in the headers so
drop it.
- {amd64,i386}/include/intr_machdep.h: NR_EVENT_CHANNELS now depends on
xen/interface/event_channel.h, so include it.
- {amd64,i386}/{amd64,i386}/support.S: It's not neccessary to include
machine/intr_machdep.h. This is also fixing build compilation with the
new headers.
- dev/xen/blkfront/blkfront.c: The typedef for blkif_request_segmenthas
been dropped. So directly use struct blkif_request_segment
Finally, modify xen/interface/xen-compat.h to throw a preprocessing error if
__XEN_INTERFACE_VERSION__ is not set. This is allow us to catch any file
where xen/xen-os.h is not correctly included.
Submitted by: Julien Grall <julien.grall@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3805
Sponsored by: Citrix Systems R&D
'rdrand' instruction may occasionally not return random numbers, in
spite of looping attempts to do so. The reusult is a KASSERT/panic.
Reluctantly accept this state-of-affairs, but make a noise about it.
if this 'noise' spams the console, it may be time to discontinue
using that source.
This is written in a general way to account for /any/ source that
might not supply random numbers when required.
Submitted by: jkh (report and slightly different fix)
Approved by: so (/dev/random blanket)
* Remove obsolete drm_agp_*_memory() prototypes.
* Fix comment in drm_fops.c (outisde -> outside).
* Fix some formatting issues in drm_stub.c (spaces -> tabs).
* Add missing case statement (gen == 3) in intel_gpu_reset().
* Restore pci_enable_busmaster() call in the init path (fixes gpu hang on i945GM).
* Replace M_WAITOK with M_NOWAIT when the return value of malloc is checked (may be incorrect).
Submitted by: <s3erios@gmail.com>
Reviewed by: dumbbell
Approved by: dumbbell
Differential Revision: https://reviews.freebsd.org/D3413
Now run(4) fetches parameters from ic->ic_wme.wme_params array, which is never initialized
(and can be safely removed). This patch replaces &ic->ic_wme.wme_params with
&ic->ic_wme.wme_chanParams.cap_wmeParams (contains parameters for local station;
used by other drivers with WME support).
Tested:
* me: STA: run0: MAC/BBP RT5390 (rev 0x0502), RF RT5370 (MIMO 1T1R), address 38:83:45:11:78:ae
Now device will use retry limit, which is set via 'ifconfig <interface>
maxretry <number>'.
Tested:
* Tested on WUSB54GC, STA mode.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3689
The MAC can be fetched from the key struct.
I added the ndis updates to make it compile.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3657
This diff includes:
* Transmitter Addresses, Keys and TKIP MIC addition to the Security Key Table.
* Proper SEC Control Registers initialization and maintenance.
* Additional flags and values in TX descriptor, which are required for encryption support.
* Error checking in RX path.
Tested:
* Tested on WUSB54GC, STA (WEP, TKIP, CCMP), HOSTAP (CCMP) and IBSS (CCMP, WPA-None) modes.
* rum0: MAC/BBP RT2573 (rev 0x2573a), RF RT2528, STA mode (CCMP+TKIP)
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3640
Note: I manually had to merge this; I merged in the "put beacon_offsets
into vap" commit before this.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3628
Don't override the NIC MAC address with an overridden MAC address for
a VAP.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3625
Tested:
* rum0: MAC/BBP RT2573 (rev 0x2573a), RF RT2528, STA mode
Note: haven't tested AP mode yet; will do once the rest of the
AP mode / power save commits are in.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3624
Move the mbuf free responsibility to the caller of the hardware xmit
function, not the hardware xmit function itself.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3621
* Remove unused sc_txtap_len/sc_rxtap_len fields.
* Remove unused ackrate variable.
* Remove unneded warning in rum_update_mcast().
* Use nitems().
* Replace some hardcoded values for RT2573_MAC_CSR1 register.
* Remove second argument for RUM_LOCK_ASSERT() - it is always the same.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3605
release resources (such as unholding pages) when errors occur. Some
recently added error checks return immediately instead of jumping to a
label resulting in leaks. Fix these to jump to a label to do cleanup
instead.
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D3745
to shut down; close laptop lid" scenario which otherwise tended to end
with a laptop overheating or the battery dying.
The implementation uses a new sysctl, kern.suspend_blocked; init(8) sets
this while rc.suspend runs, and the ACPI sleep code ignores requests while
the sysctl is set.
Discussed on: freebsd-acpi (35 emails)
MFC after: 1 week
The fullmac firmware doesn't seem to populate a useful rssi indicator
in the RX descriptor, so if one plotted said values, they'd basically
look like garbage.
The reference driver implements a "get current rssi" firmware command
which I guess is really meant for station operation only (as hostap
operation would need rssi per station, not a single firmware read.)
So:
* populate sc_currssi during each calibration run;
* use this in the RX path instead of trying to reconstruct the RSSI
value and passing it around as a pointer;
* do up a quick hack to map the rssi hardware value to some useful
signal level;
* the survey results provide an RSSI value between 0..100, so just
do another quick hack to map it into some usefulish signal level;
* supply a faked noise floor - I haven't yet found how to pull it
out of the firmware.
The scan results and the station RSSI information is now more useful
for indicating signal strength / distance.
- Remove write-only SBUF_ULP_FLAG_COALESCE_OFF flag.
- Failure to allocate ulp_mbuf_cb during rx is a hard error. Panic
instead of just freeing the mbuf and pretending nothing happened. The
payload in the mbuf is precious because it has been ACK'ed by the TOE.
(ulp_mbuf_cb is going to go away soon and so will these potential
failures during rx.)
This logic is mostly crimed from the reference driver and the linux
r92su driver.
I verified that it (a) worked on the rsu hardware I have, and (b)
did traffic testing whilst watching what ath(4) sent as a hostap.
It successfully sent MCS8..15 rates (which requires 2-stream reception)
as well as MCS0..7 (which is 1-stream.)
Tested:
* RTL8712, 1T1R NIC, MCS rates 0..7.
* RTL8712, 1T2R NIC, MCS rates 0..15
TODO:
* Find a 2T2R NIC!
* include opt_wlan.h like a good little wlan driver;
* add a function to free the mbufq /and/ the node references on it, or we will leak
said node references;
* free the mbufq upon NIC shutdown otherwise we may end up with a full list that
we never begin transmit work on, and thus never drain it;
* .. which frees it upon NIC detach too;
* ensure urtwn_start() gets called after the completion of frame TX even if the
pending queue is empty, otherwise transmit will stall. It's highly unlikely that
the usb tx queue would be empty whilst the incoming send queue is full, but hey,
who knows.
This passes some iperf testing with and without the NIC being actively removed during
said active iperf test.
Tested:
* urtwn0: MAC/BB RTL8188EU, RF 6052 1T1R ; STA mode
Fast-frames:
* include opt_wlan.h ; tsk to not doing it earlier;
* add a tx pending tracking counter for seeing how deep
the hardware TX queue is;
* add the frame aging code from if_ath;
* add fast-frames capability to the driver setup.
Bugs:
* free the buffers (and node references) before
detaching net80211 state. This prevents a use-after-free in
the node free path where we've destroyed net80211 underneath it.
Don't make an integer to a boolean and then compare to a value which
needs an integer comparison.
Spotted by: reading kernel compile time log
MFC after: 2 weeks
in the join message so the firmware would pick it up.
* Strip out the direct hardware fiddling for 40MHz mode - the firmware
we're using doesn't require it (the rtl8712su firmware does; it
is less 'fullmac' than what we're using.)
* Fix the mbuf handling during errors - rsu_tx shouldn't free mbufs;
it's up to the caller to do so. This brings it in line with
what other drivers do or should be doing.
Tested:
* RTL8712, HT40 channel, STA mode (during this commit)
Atheros.
Thanks to OpenBSD for providing a driver based on the original
Atheros open source driver circa 2008. This uses the early, pre-carl9170
atheros provided firmware.
It only supports 11bg at the moment. I've not tested it with 11a
(and so the TX rate control logic may be slightly wrong!) so if
you do have the dual-band version of this hardware please do let me know.
Tested:
* AR9170, TP-Link WN821N 2GHz.
TODO:
* Hook this up to a non-module build.
Refer to the usb_quirk(4) manual page for more details on how to use
this new feature.
Submitted by: Maxime Soule <btik-fbsd@scoubidou.com>
PR: 203249
MFC after: 2 weeks
* Don't free the mbuf in the tx path - it uses the transmit path now,
so the caller frees the mbuf.
* Don't decrement the node ref upon error - that's up to the caller to
do as well.
Tested:
* Intel 5300 3x3 wifi, station mode
Noticed by: <s3erios@gmail.com>
* Add a new method to control NIC poweron / network-sleep / power off;
* Add in A-MPDU TX negotiation support, but comment it out because it
does break TX traffic;
* blank out the tx buffer before sending a firmware message, just in case;
* go into network-sleep once associated;
TODO:
* figure out why ampdu negotiation isn't working and breaking TX traffic,
then enable it.
to do it directly.
Ensure that we re-queue starting transmit upon TX completion.
This solves two issues:
* It stops tx stalls - before this, if the transmit path filled the
mbuf queue then it'd never start another transmit.
* It enforces ordering - this is very required for 802.11n which
requires frames to be transmitted in the order they're queued.
Since everything remotely involved in USB has an unlock/thing/relock
pattern with that mutex, the only way to guarantee TX ordering is
to 100% defer it into a separate thread.
This now survives an iperf test and gets a reliable 30mbit/sec.
Correctly (I hope!) remove net80211 references before doing so.
Just doing a dumb mbufq drain isn't enough.
If enough traffic occurs and the mbuf queue fills up then transmit
stalls (which I'm not fixing in this commit!) but then the mbuf queue
stays full until the driver is removed. There's also the net80211
node refcounting leak.
This just ensures that during rsu_stop and detach the mbuf queue
is purged (and references!) so the queue-full situation can be
recovered from.
setup pieces and so (at least) transmit doesn't work.
It'll just fall back to being a straight HT20 device and negotiate
HT20 only.
Tested by: Idwer Vollering <vidwer@gmail.com>
This also adds a newbus interface that allows a SoC to override the
following settings:
- if_dwc specific SoC initialization;
- if_dwc descriptor type;
- if_dwc MII clock.
This seems to be an old version of the hardware descriptors but it is
still in use in a few SoCs (namely Allwinner A20 and Amlogic at least).
Tested on Cubieboard2 and Banana pi.
Tested for regressions on Altera Cyclone by br@ (old version).
Obtained from: NetBSD
requirements.
Don't start the opmode and join path until a pending survey is finished.
This seems to reliably fix things.
Ideally I'd just finish off the net80211 pluggable scan stuff and implement
the methods here so if_rsu can just drive the scan machinery.
However, that's a .. later thing.
Whilst here, remove the getbuf debugging; it's okay to run out of transmit
buffers under load; it however isn't okay to not be able to send commands.
I'll fix that later.
* Add a tunable to enable 11n if it's available, so to not anger people
who upgrade.
kenv hw.usb.rsu.enable_11n=1 before inserting the device.
* Add initial 11n htconfig bits;
* Enable 40MHz mode if it's available;
* Add 11n channels;
* Set 11n bits in the firmware.
It works for RX; I haven't tested TX aggregation just yet.
However the firmware doesn't do RX re-ordering, so I have to tie it into
the net80211 A-MPDU RX reorder path before I flip this on by default.
I've verified that I'm indeed actually seeing MCS 0->7 rates being received.
I haven't dug into whether it's actually transmitting 11n rates; I'll dig into
that later.
* the tx descriptor TID is priority, not TID.
* the tx descriptor queue id mapping is separate from the
TID/priority; rather than just "BE".
TODO:
* go and re-re-re-verify the queue mappings; the linux and openbsd
mappings aren't exactly the same. I need to verify all of this
before I try to flip on 11n RX.
* Do 1T1R for now, until we read the config out of ROM and use it.
* Disable turbo mode, I dunno what this is, but the linux drivers
have this disabled.
* Set the firmware endpoints to what we read from USB.
Tested:
* RTL8712 cut 3, STA mode
data queues.
This is similar to the openbsd and rtlwifi/r92su drivers.
Note: this driver still assumes it's a 4-endpoint device; I'll enforce
that in a follow-up commit.
When the system has more than a single PCI domain, the bus numbers
are not unique, thus they cannot be used for "pci" device numbering.
Change bus numbers to -1 (i.e. to-be-determined automatically)
wherever the code did not care about domains.
Reviewed by: jhb
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3406
There is an issue with interrupts at the moment, but it works with
polling mode set (hw.usb.xhci.use_polling=1).
Reviewed by: hselasky
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3665
This allows for arbitrary channel info to be placed in the input call rather
than the totally gross hack of overriding ic_curchan.
Without this I'm sure ic_curchan setting was racing with the scan code
setting the channel itself..
The firmware in this NIC sends management frames. So far I'm not sure which
ones it handles and which ones it doesn't handle - but this is what openbsd
does.
The association messages are handled by the firmware; the key negotiation
for 802.1x and WPA are done as raw frames, not management frames.
This successfully allows it to associate to my home networks whereas it didn't
work beforehand.
Tested:
* RTL8712, cut 3, STA mode
TODO:
* The firmware does send a join response with a status code; that should be
logged in a more obvious way to assist with debugging. Ie, the firmware
is the thing that is saying "couldn't join, sorry!", not net80211.
to attach with the last version of this commit. This commit fixes
attach failures on "ICH8" class devices via modifications to
e1000_init_nvm_params_ich8lan()
- Fix compiler warning in 80003es2lan.c
- Add return value handler for e1000_*_kmrn_reg_80003es2lan
- Fix usage of DEBUGOUT
- Remove unnecessary variable initializations.
- Removed unused variables (complaints from gcc).
- Edit defines in 82571.h.
- Add workaround for igb hw errata.
- Shared code changes for Skylake/I219 support.
- Remove unused OBFF and LTR functions.
Tested by some of the folks that reported breakage in previous incarnation.
Thanks to AllanJude, gjb, gnn, tijl for tempting fate with their machines.
Submitted by: erj@freebsd.org
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D3162
* yes, when a "sta disconnect" message comes through we should, like,
disconnect things. We're not currently generating beacon miss messages,
and net80211 isn't disconnecting things via software beacon miss receive.
Tested:
* RTL8712, cut 3, STA mode
* use an ath/iwn style debug bitmap - it's still global rather than per-device,
but it's better than debug levels
* disable bgscan - it just makes things unstable/unpredictable for now.
Tested:
* if_rsu - RTL8712 cut 3, STA mode
The pci bus driver handles the power state, it also manages
configuration state saving and restoring for its child devices. Thus a
PCI device driver does not have to worry about those things. In fact, I
observe a hard system hang when trying to suspend a system with active
radeonkms driver where both the bus driver and radeonkms driver try to
do the same thing. I suspect that it could be because of an access to a
PCI configuration register after the device is placed into D3 state.
Reviewed by: dumbbell, jhb
MFC after: 13 days
Differential Revision: https://reviews.freebsd.org/D3561
vendor supplied device trees contain the needed properties for us to select
the correct uart to use as the kernel console.
An example of this would be to add the following to loader.conf.
hw.fdt.console="/smb/uart@f7113000"
The intention of this is slightly different than the existing
hw.uart.console option. The new option will mean the boot serial
configuration will be derived from the device node, while the existing
option expects the user to configure all this themselves.
Further work is planned to allow the uart configuration to be set based on
the stdout-path property devicetree bindings.
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D3559
Certain VM guest types (VMware, Xen) do not support MSI, so pci_alloc_msix()
always fails. isci(4) was not properly detecting the allocation failure,
and would try to proceed with MSIx resource initialization rather than
reverting to INTx.
Reported and tested by: Bradley W. Dutton (brad-fbsd-stable@duttonbros.com)
MFC after: 3 days
Sponsored by: Intel
BIOS always enables PCI busmaster on the isci device, which effectively
worked around this omission. But when passing the isci device through
to a guest VM, the hypervisor will disable busmaster and isci will not
work without calling pci_enable_busmaster().
MFC after: 3 days
Sponsored by: Intel
This is a subtle use-after-free race that results in some very undesirable
hang behaviour.
Reviewed by: pkelsey
Obtained from: Kip Macy, NextBSD (91a9bd1dbb)
Gleaned from a public header file. 5402 and 5404 look like they may be
used on embedded devices. 5478 and 5488 are switch PHYs. 5754 change is just
to note a product alias.
Differential Revision: https://reviews.freebsd.org/D3338
Submitted by: kevin.bowling@kev009.com
delete a logic volume on status change which is NOT what we want here.
The original code is correct in that when the volume changes status
the driver will only delete the volume if the status is one of the
fatal errors. A drive failure in a mirrored volume is NOT a situtation
where the volume should dissapear.
Reported on freebsd-scsi@:
https://lists.freebsd.org/pipermail/freebsd-scsi/2015-September/006800.html
MFC after: 3 days
Resetting some generations of the I/OAT hardware (just BDXDE for now)
resets the corresponding MSI-X registers. So, teardown and
re-initialize interrupts after resetting the hardware.
Reviewed by: jimharris
Approved by: markj (mentor)
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3549
SoC is used in the HiKey board from 96boards.
Currently on the SD card is working on the HiKey, as such devices 0 and 2
will need to be disabled, for example by adding the following to
loader.conf:
hint.hisi_dwmmc.0.disabled=1
hint.hisi_dwmmc.2.disabled=1
Relnotes: yes (Hikey board booting)
Sponsored by: ABT Systems Ltd
in Marvell terms) to 32768. 32768 looks overkill but it will
ensure correct DMAed update. This change addresses occasional
watchdog timeouts reported on 10.2-RELEASE.
Tested by: Johann Hugo <jhugo@meraka.csir.co.za>
MFC after: 2 weeks
only gpiobus configured via FDT is supported. Bus enumeration is
supported. Devices are created for each device found. 1-Wire
temperature controllers are supported, but other drivers could be
written. Temperatures are polled and reported via a sysctl. Errors
are reported via sysctl counters. Mis-wired bus detection is included
for more trouble shooting. See ow(4), owc(4) and ow_temp(4) for
details of what's supported and known issues.
This has been tested on Raspberry Pi-B, Pi2 and Beagle Bone Black
with up to 7 devices.
Differential Revision: https://reviews.freebsd.org/D2956
Relnotes: yes
MFC after: 2 weeks
Reviewed by: loos@ (with many insightful comments)
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
While here update the list of devices id to match the one in linux 3.8.13
Reviewed by: dumbbell
Differential Revision: https://reviews.freebsd.org/D3489
Keep a couple of old macros that will be removed lated when the rest of the code
will be updated to 3.8.13 equivalent.
Chase the renamed macros
Reviewed by: dumbbell
Differential Revision: https://reviews.freebsd.org/D3487
Convert filemon_lock and struct filemon* lock to sx(9), rather than a
self-rolled reader-writer lock, and hold it for the entire time needed.
At least filemon_lock_write() was not checking for active readers when
it would successfully return with the write lock "held". This led to
a race with reading entries from filemon_inuse as they were removed. This
could be seen with QUEUE_MACRO_DEBUG enabled, causing -1 to be read as an
entry rather than a valid struct filemon*.
Fixing filemon_lock_write() to check readers was insufficient to fix the
races.
sx(9) was used as the lock could be held while taking proctree_lock and sleeping
in fo_write.
Sponsored by: EMC / Isilon Storage Division
MFC after: 2 weeks
