tables. Some drivers needed some slight re-arrangement of declarations
to accommodate this. Change the USB pnp tables slightly to allow
better compatibility with the system by moving linux driver info from
start of each entry to the end. All other PNP tables in the system
have the per-device flags and such at the end of the elements rather
that at the beginning.
Differential Review: https://reviews.freebsd.org/D3458
o The CP2101 and CP2102 do not support GPIO pin use at all, enforce this.
o Support reading the GPIO status on the second port of the CP2105. More
work is needed before the CP2105 GPIO pins can be used as outputs.
Hardware donated by: Silicon Labs
MFC after: 3 weeks
"device_free_softc()" and "device_claim_softc()",
to allow USB serial drivers refcounting the softc.
These functions are used to grab the softc from
auto-free and to free the softc back to the correct
malloc type, respectivly.
Discussed with: jhb
MFC after: 2 weeks
make maintaining this driver from the documentation easier in the future.
This is a mostly mechanical change.
In uslcom_param(), move the zeroing of the final two fields of the
flowctrl structure outside of the "if CRTSCTS" section - not only were
they being zeroed in both the clauses, but these two fields have nothing
to do with hardware flow control anyway.
the device_detach() function doesn't block on UCOM device
drivers until the TTY handle is closed by the userspace
application. This is implemented by a postpone of the
softc free where the UCOM structures reside until the
TTY references are gone.
Discussed with: kib, ed
MFC after: 2 weeks
Use the interface number from the USB interface descriptor
like in the other USB serial drivers. These numbers are not
supposed to be different, though in theory they can. Make sure
that the driver then uses the interface number given by the USB
descriptor, and not the logical index of the USB stack.
For the future:
Whenever the term "index" is used in the USB code, it refers to
a number computed by the USB stack.
Whenever the term "number" is used in the USB code, it refers to
a number in a USB descriptor.
MFC after: 2 weeks
support for only the first port, but the CP2105 can have multiple ports.
Although this allowed the first port to mostly work on multi port devices,
there could be issues with this arrangement.
Update the man page to reflect support for both ports and the CP2105.
Many thanks to Silicon Labs (www.silabs.com) for providing a CP2105-EK
dev board for testing.
MFC after: 2 weeks
list of supported devices with the union of:
NetBSD src/sys/dev/usb/uslsa.c 1.18
OpenBSD src/sys/dev/usb/uslcom.c 1.24
Linux source/drivers/usb/serial/cp210x.c HEAD
Remove duplicate JABLOTRON PC60B entry.
Note that some of the devices added here are multi-port devices. The
uslcom(4) driver currently only supports the first port on such devices.
Update the man page to reflect the full list of supported devices.
Remove two caveats from the CAVEATS section, as both listed caveats no
longer apply. Add a caveat about multi-port devices.
MFC after: 2 weeks
- The USLCOM_SET_BAUD_DIV command (0x01)
- The USLCOM_SET_BAUD_RATE command (0x13)
Devices based on the CP1204 will only accept the latter command, and ignore
the former. As the latter command works on all chips that this driver
supports, switch to always using it.
A slight confusion here is that the previously used command was incorrectly
named USLCOM_BAUD_RATE - even though we no longer use it, rename it to
USLCOM_SET_BAUD_DIV to closer match the name used in the datasheet.
This change reflects a similar change made in the Linux driver, which was
submitted by preston.fick at silabs.com, and has been tested on all of the
uslcom(4) devices I have to hand.
MFC after: 2 weeks
cp2103 usb-to-serial chip.
- This patch also makes the line status polling asynchronous, to reduce
the time needed to change the GPIO pins.
Submitted by: JD Louw
MFC after: 1 week
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
sorted according to the mode which they support:
host, device or dual mode
- Add generic tool to extract these data:
tools/bus_autoconf
Discussed with: imp
Suggested by: Robert Millan <rmh@debian.org>
PR: misc/157903
MFC after: 14 days
all new devices added between our r211022 and their git revision
93ad03d60b5b18897030038234aa2ebae8234748
Also correct a Foxconn entry.
MFC after: 1 week
information through devd. My E220 now produces the notification (1 line):
+u3g0 at bus=1 hubaddr=1 port=0 devaddr=2 interface=0 \
vendor=0x12d1 product=0x1003 devclass=0x00 devsubclass=0x00 \
sernum="" release=0x0000 intclass=0xff intsubclass=0xff \
ttyname=U0 ttyports=2 on uhub0
Note: serial/ufoma and net/uhso still provide port number and tty name
(uhso only) information through sysctls, which should now be removed.
Reviewed by: hpselasky
- hw.usb.ucom.cons_unit is now split into
hw.usb.ucom.cons_unit/...cons_subunit.
Note: The tunable/sysctl hw.usb.ucom.cons_unit needs to be reviewed if
a) a console was defined a USB serial devices, and a USB device with
more than 1 subunit is present, and this device is attached before the
device functioning as a console
or
b) a console was defined on a USB device with more than 1 subunit
Reviewed by: hps
MFC after: 2 weeks
and BeOS. The devices supported by uslcom(4) are now in sync with:
NetBSD src/sys/dev/usb/uslsa.c 1.11
OpenBSD src/sys/dev/usb/uslcom.c 1.20
Linux source/drivers/usb/serial/cp210x.c from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Two vendor/product IDs from Linux have not been added to uslcom(4):
SILABS SAEL - This device has special code in u3g to support it
SILABS GSM2228 - I suspect this should also be covered by u3g(4).
MFC after: 1 week
- Bring in several other devices from OpenBSD while here. Use the
official manufacturer name over the OpenBSD name in the case of
GEMALTO. Reorder list slightly to aid future syncing.
- Remove duplicate SILABS CP2102 define from usbdevs
PR: usb/131912 [1]
Submitted by: Jack Twilley <mathuin gmail.com> [1]
MFC after: 1 week
- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" which select for which mode
the current xfer entry is active. Options are: a) Device mode only b) Host
mode only (default-by-zero) c) Both modes. This change was scripted using
the following sed script: "s/\.mh\././g".
- the standard packet size table in "usb_transfer.c" is now a function, hence
the code for the function uses less memory than the table itself.
Submitted by: Hans Petter Selasky
