system retrieve its config data from the fdt data.
The properties that are common to all phys are decoded and returned in a
structure. The fdt node handles for the mac and phy devices are also
returned in the config data struct, so a driver can easily obtain additional
hardware-specific config values from the fdt data.
While the initial need for this is to help support phy drivers which are
configured with FDT data, there is nothing devicetree-specific about the
concept or the names, so they are available for use even on non-FDT systems.
The initial list of connection types comes from the current devicetree
bindings documentation, but values not documented there can be added to
the list in the future as needed, the values could be sorted into a
different order without perturbing FDT code, etc. The only invariant
is that MII_CONTYPE_UNKNOWN should be first (so it has a value of zero,
so that a con-type variable in a softc, for example, is initialized to
MII_CONTYPE_UNKNOWN by default).
After harvesting the hardware statistics counters and summing them into the
interface stats, properly clear the hardware counters back to zero. On imx5
and earlier hardware it is necessary to disable collection of stats while
writing zeroes to all the registers. On imx6 and newer it turns out it's
not even possible to write zeroes, instead you have to toggle a special
"zero everything" control bit in a register.
Count incoming packets with a bad start frame delim as input errors, and
incoming packets dropped due to no fifo space as input drops.
Remove all code related to harvesting the hardware stats less often than
once per second. It turns out the 32-bit stats registers are backed by
16-bit counters under the hood, and they can easily roll over if you only
harvest them once every 3 seconds like the old code was doing. Now we just
read all the regs once a second.
The combination of not properly zeroing the stats registers and 16-bit
counters sometimes wrapping between harvest calls resulted in basically
unusable statistics before these changes.
Description from Brett:
"The busdma tags used to create mappings for the tx and rx rings did not have
the device's tag as parents, meaning that they did not respect the device's
busdma properties. The other tags used in the driver had their parents set
appropriately.
Also, the dma maps for each buffer in ixl_txeof() were being NULLed after
being unloaded, which is an error because those maps are then reused without
being recreated (I believe this also leaked resources since the maps were not
destroyed). Simply removing the line that sets the maps to NULL gives the
desired behavior. There does not seem to be a similar problem with ixl_rxeof().
Functions to free the tx and rx rings also NULL out the dma maps for each
buffer, but this seems okay because the maps are destroyed and not reused in
this case.
With these fixes, my ixl card seems to be working with the IOMMU enabled."
Submitted by: Brett Gutstein <bgutstein@rice.edu>
Reviewed by: erj
Approved by: Alan Cox <alc@rice.edu>
MFC after: 1 week
illumos/illumos-gate@79809f9cf479809f9cf4https://www.illumos.org/issues/8269
It seems that currently normalization of stddev aggregation is done
incorrectly.
We divide both the sum of values and the sum of their squares by the
normalization factor. But we should divide the sum of squares by the
normalization factor squared to scale the original values properly.
FreeBSD note: the actual change was committed in r316853, this commit
adds the test files and record merge information.
Reviewed by: Bryan Cantrill <bryan@joyent.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: Andriy Gapon <avg@FreeBSD.org>
MFC after: 1 week
Sponsored by: Panzura
o Separate fields of struct socket that belong to listening from
fields that belong to normal dataflow, and unionize them. This
shrinks the structure a bit.
- Take out selinfo's from the socket buffers into the socket. The
first reason is to support braindamaged scenario when a socket is
added to kevent(2) and then listen(2) is cast on it. The second
reason is that there is future plan to make socket buffers pluggable,
so that for a dataflow socket a socket buffer can be changed, and
in this case we also want to keep same selinfos through the lifetime
of a socket.
- Remove struct struct so_accf. Since now listening stuff no longer
affects struct socket size, just move its fields into listening part
of the union.
- Provide sol_upcall field and enforce that so_upcall_set() may be called
only on a dataflow socket, which has buffers, and for listening sockets
provide solisten_upcall_set().
o Remove ACCEPT_LOCK() global.
- Add a mutex to socket, to be used instead of socket buffer lock to lock
fields of struct socket that don't belong to a socket buffer.
- Allow to acquire two socket locks, but the first one must belong to a
listening socket.
- Make soref()/sorele() to use atomic(9). This allows in some situations
to do soref() without owning socket lock. There is place for improvement
here, it is possible to make sorele() also to lock optionally.
- Most protocols aren't touched by this change, except UNIX local sockets.
See below for more information.
o Reduce copy-and-paste in kernel modules that accept connections from
listening sockets: provide function solisten_dequeue(), and use it in
the following modules: ctl(4), iscsi(4), ng_btsocket(4), ng_ksocket(4),
infiniband, rpc.
o UNIX local sockets.
- Removal of ACCEPT_LOCK() global uncovered several races in the UNIX
local sockets. Most races exist around spawning a new socket, when we
are connecting to a local listening socket. To cover them, we need to
hold locks on both PCBs when spawning a third one. This means holding
them across sonewconn(). This creates a LOR between pcb locks and
unp_list_lock.
- To fix the new LOR, abandon the global unp_list_lock in favor of global
unp_link_lock. Indeed, separating these two locks didn't provide us any
extra parralelism in the UNIX sockets.
- Now call into uipc_attach() may happen with unp_link_lock hold if, we
are accepting, or without unp_link_lock in case if we are just creating
a socket.
- Another problem in UNIX sockets is that uipc_close() basicly did nothing
for a listening socket. The vnode remained opened for connections. This
is fixed by removing vnode in uipc_close(). Maybe the right way would be
to do it for all sockets (not only listening), simply move the vnode
teardown from uipc_detach() to uipc_close()?
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D9770
- For HMAC requests, construct a special input buffer to request an empty
hash result.
- For plain cipher requests and requests that chain an AES cipher with an
HMAC, fail with EINVAL if there is no cipher payload. If needed in
the future, chained requests that only contain AAD could be serviced as
HMAC-only requests.
- For GCM requests, the hardware does not support generating the tag for
an AAD-only request. Instead, complete these requests synchronously
in software on the assumption that such requests are rare.
Sponsored by: Chelsio Communications
during bootup. Debugging information shows that softclock_call_cc() is
trying to execute the vt_consdev.vd_timer callout, and the callout
structure contains a NULL c_func.
This appears to be due to a race between vt_upgrade() running
callout_reset() and vt_resume_flush_timer() calling callout_schedule().
Fix the race by ensuring that vd_timer_armed is always set before
attempting to (re)schedule the callout.
Discussed with: emaste
MFC after: 2 weeks
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D9828
Currently the PCI domain is initialized with the instance GUID in
vmbus_pcib_attach(). It turns out the GUID can change across VM reboot,
while some users want a persistent value for PCI domain. The solution is
that we can change to use the device serial number, which starts with 1
and is unique within a VM.
Obtained from: Haiyang Zhang
MFC after: 1 day
Sponsored by: Microsoft
* Firmware versions 21 and 22 generate some IWM_DEBUG_LOG_MSG notifications,
which seem to be harmless. Avoid spamming the system log with
"frame ... UNHANDLED (this should not happen)" messages.
Obtained from: dragonflybsd.git dda889ac57d8e5b46bb1b1ecf53c17a18481c7c8
* If device family is 8000 then iwm_pcie_load_cpu_sections()
won't be called at all (iwm_pcie_load_cpu_sections_8000() is
called in that case) so this piece of code never gets called.
Obtained from: dragonflybsd.git 3e9aaef308100a4d630feffc131e3aca2ae12f8a
* LAR can be disabled with the hw.iwm.lar.disable tunable now.
* On Family 8000 devices we need to check the lar_enabled flag from
nvm_data in addition to the TLV_CAPA_LAR_SUPPORT flag from the firmware.
* Add a separate IWM_DEBUG_LAR debugging flag.
Obtained from: dragonflybsd.git 0593e39cb295aa996ecf789ed4990c3b255f1770
* This change also fixes a possible issue in the existing smart-fifo code,
which set the IWM_SF_CFG_DUMMY_NOTIF_OFF bit on AC8260 chipsets, although
that's only used in iwlwifi for Family 8000 chipsets connected via SDIO
interface.
Obtained from: Dragonflybsd.git cb650b01526b0aeef3c4307d926e7f1428997d50
The stdout-path chosen property may include the serial connection details,
e.g. the baud rate. When passing the device to OF_finddevice we need to
strip off this information as it will cause the lookup to fail.
Reviewed by: emaste, manu
Differential Revision: https://reviews.freebsd.org/D6846
is the same as the old MTU. In particular, on Amazon EC2 "T2" instances
without this change, the network interface is reinitialized every 30
minutes due to the MTU being (re)set when a new DHCP lease is obtained,
causing packets to be dropped, along with annoying syslog messages about
the link state changing.
As a side note, the behaviour this commit fixes was responsible for
exposing the locking problems fixed via r318523 and r318631.
Maintainers of other network interface drivers may wish to consider making
the corresponding change; the handling of SIOCSIFMTU does not seem to
exhibit a great deal of consistency between drivers.
MFC after: 1 week
mlx4en(4) driver in SRIOV mode.
Place a copy of the destination MAC address in the send WQE only under
SRIOV/eSwitch configuration or when the device is in selftest. This
allows communication between functions on the same host.
PR: 216493
MFC after: 3 days
Sponsored by: Mellanox Technologies
driver. Else if the port is up the resource might still be busy and
the MTT free will fail.
PR: 216493
MFC after: 3 days
Sponsored by: Mellanox Technologies
Add -o [no]verify option to mdconfig (and document in man page.)
Implement GEOM attribute MNT::verified to ask md if the backing vnode is
verified.
Check for MNT::verified in cd9660 mount to flag the mount as MNT_VERIFIED if
the underlying device has been verified.
Reviewed by: rwatson
Approved by: sjg (mentor)
Obtained from: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D2902
Use the SDHCI_CAN_DRIVE_TYPE_A/_C/_D masks to check for Driver Type support,
instead of using the SDHCI_CTRL2_DRIVER_TYPE_A/_C/_D values which are meant
for setting the Driver Type in the HOST_CONTROL2 register.
Approved by: adrian (mentor), jmcneill
Differential Revision: https://reviews.freebsd.org/D10999
There could be race condition with TX cleaning routine when cleaning mbufs,
when it was called directly from main sending thread (ena_mq_start).
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon.com Inc.
Differential revision: https://reviews.freebsd.org/D10927
Initially, stats were being updated each time OS was requesting for
the first statistic.
To read statistics from hw, condvar was used. cv_timedwait cannot be
called when unsleepable lock is held, and this happens when FreeBSD
is requesting statistic.
Seperate task is reading statistics from NIC each 1 second.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon.com Inc.
Differential revision: https://reviews.freebsd.org/D10926
Also, to simplify cleaning routine, reset task is initialized before
allocating statistics and other resources.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon.com Inc.
Differential revision: https://reviews.freebsd.org/D10925
Lock only ena_up and ena_down calls in ioctl handler, instead of whole
ioctl. Locking ioctl with sx lock that is sleepable, is not allowed in
some cases, e.g. when multicast options are being changed.
Additional locking was added in deatch function to prevent race condition
with ioctl function.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon.com Inc.
Differential revision: https://reviews.freebsd.org/D10924
When mbuf chain is too long and device cannot handle that number
of segments in DMA transaction, mbuf chain will be defragmented.
Initially, driver was dropping all mbuf chains that were exceeding
supported number of segments.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon.com Inc.
Differential revision: https://reviews.freebsd.org/D10923
Both relative and absolute multitouch modes are supported.
To enable psm(4) evdev support one should:
1. Add `device evdev` and `options EVDEV_SUPPORT` to kernel config file
2. Add hw.psm.elantech_support=1 or hw.psm.synaptics_support=1 to
/boot/loader.conf for activation of absolute mode on touchpads
3. Add kern.evdev.rcpt_mask=12 to /etc/sysctl.conf to enable psm event
sourcing and disable sysmouse
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10265
Tested by: wulf, Jan Kokemueller (Lenovo devs)
It turned out, that some models of the Atheros PCIe
adapters (e.g. AR983x family) may fail to attach
due to insufficient timeout value.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: adrian
Differential revision: https://reviews.freebsd.org/D10903
sc_set_media_status() callback may involve some generic code in addition to
firmware-specific part (e.g., link status register setup for RTL8188E);
so, remove 'RTWN_WITHOUT_UCODE' ifdefs around it.
Tested with RTL8188CUS, RTL8188EU and RTL8821AU, STA mode.
Tested on WZR-HP-G301NH(RTL8366RB) and WZR-HP-G300NH(RTL8366SR).
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Differential Revision: https://reviews.freebsd.org/D10740
- Fix typo of PLL Type 4
- Don't panic of frequency getters
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Differential Revision: https://reviews.freebsd.org/D10967
The adapter firmware in general does not accept PDUs larger than 64k - 1
bytes in size. Sending crypto requests larger than this size result in
hangs or incorrect output, so reject them with EFBIG. For requests
chaining an AES cipher with an HMAC, the firmware appears to require
slightly smaller requests (around 512 bytes).
Sponsored by: Chelsio Communications
The crash can occur when all of the following conditions are true:
- a packet consists of multiple segements (requires LRO enabled)
- there has been a failure to allocate an mbuf for the packet and
the packet has to be dropped
- a host (vmware) still owned at least one segment of the packet,
so the driver had to wait for another interrupt to proceed to
discarding the remaning segment(s)
Reviewed by: rstone
MFC after: 2 weeks
Sponsored by: Panzura
Differential Revision: https://reviews.freebsd.org/D10874
In the deep past, when this code compiled as a binary module, ath_hal
built as a module. This allowed custom, smaller HAL modules to be built.
This was especially beneficial for small embedded platforms where you
didn't require /everything/ just to run.
However, sometime around the HAL opening fanfare, the HAL landed here
as one big driver+HAL thing, and a lot of the (dirty) infrastructure
(ie, #ifdef AH_SUPPORT_XXX) to build specific subsets of the HAL went away.
This was retained in sys/conf/files as "ath_hal_XXX" but it wasn't
really floated up to the modules themselves.
I'm now in a position where for the reaaaaaly embedded boards (both the
really old and the last couple generation of QCA MIPS boards) having a
cut down HAL module and driver loaded at runtime is /actually/ beneficial.
This reduces the kernel size down by quite a bit. The MIPS modules look
like this:
adrian@gertrude:~/work/freebsd/head-embedded/src % ls -l ../root/mips_ap/boot/kernel.CARAMBOLA2/ath*ko
-r-xr-xr-x 1 adrian adrian 5076 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_dfs.ko
-r-xr-xr-x 1 adrian adrian 100588 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_hal.ko
-r-xr-xr-x 1 adrian adrian 627324 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_hal_ar9300.ko
-r-xr-xr-x 1 adrian adrian 314588 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_main.ko
-r-xr-xr-x 1 adrian adrian 23472 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_rate.ko
And the x86 versions, like this:
root@gertrude:/home/adrian # ls -l /boot/kernel/ath*ko
-r-xr-xr-x 1 root wheel 36632 May 24 18:32 /boot/kernel/ath_dfs.ko
-r-xr-xr-x 1 root wheel 134440 May 24 18:32 /boot/kernel/ath_hal.ko
-r-xr-xr-x 1 root wheel 82320 May 24 18:32 /boot/kernel/ath_hal_ar5210.ko
-r-xr-xr-x 1 root wheel 104976 May 24 18:32 /boot/kernel/ath_hal_ar5211.ko
-r-xr-xr-x 1 root wheel 236144 May 24 18:32 /boot/kernel/ath_hal_ar5212.ko
-r-xr-xr-x 1 root wheel 336104 May 24 18:32 /boot/kernel/ath_hal_ar5416.ko
-r-xr-xr-x 1 root wheel 598336 May 24 18:32 /boot/kernel/ath_hal_ar9300.ko
-r-xr-xr-x 1 root wheel 406144 May 24 18:32 /boot/kernel/ath_main.ko
-r-xr-xr-x 1 root wheel 55352 May 24 18:32 /boot/kernel/ath_rate.ko
.. so you can see, not building the whole HAL can save quite a bit.
For example, if you don't need AR9300 support, you can actually avoid
wasting half a megabyte of RAM. On embedded routers this is quite a
big deal.
The AR9300 HAL can be later further shrunk because, hilariously,
it indeed supports AH_SUPPORT_<xxx> for optionally adding chipset support.
(I'll chase that down later as it's quite a big savings if you're only
building for a single embedded target.)
So:
* Create a very hackish way to load/unload HAL modules
* Create module metadata for each HAL subtype - ah_osdep_arXXXX.c
* Create module metadata for ath_rate and ath_dfs (bluetooth is
currently just built as part of it)
* .. yes, this means we could actually build multiple rate control
modules and pick one at load time, but I'd rather just glue this
into net80211's rate control code. Oh well, baby steps.
* Main driver is now "ath_main"
* Create an "if_ath" module that does what the ye olde one did -
load PCI glue, main driver, HAL and all child modules.
In this way, if you have "if_ath_load=YES" in /boot/modules.conf
it will load everything the old way and stuff should still work.
* For module autoloading purposes, I actually /did/ fix up
the name of the modules in if_ath_pci and if_ath_ahb.
If you want to selectively load things (eg on ye cheape ARM/MIPS platforms
where RAM is at a premium) you should:
* load ath_hal
* load the chip modules in question
* load ath_rate, ath_dfs
* load ath_main
* load if_ath_pci and/or if_ath_ahb depending upon your particular
bus bind type - this is where probe/attach is done.
TODO:
* AR5312 module and associated pieces - yes, we have the SoC side support
now so the wifi support would be good to "round things out";
* Just nuke AH_SUPPORT_AR5416 for now and always bloat the packet
structures; this'll simplify other things.
* Should add a simple refcnt thing to the HAL RF/chip modules so you
can't unload them whilst you're using them.
* Manpage updates, UPDATING if appropriate, etc.
in the PCM feeder mixer. Without this change a value of 32 channels is
treated like zero, due to using a mask of 0x1f, causing a kernel
assert when trying to playback bitperfect 32-channel audio. Also
update the AWK script which is generating the division tables to
handle more than 18 channels. This commit complements r282650.
MFC after: 3 days
This brings the AHB support in line with the PCI support - now other "things"
can wrap up the calibration / board data into a firmware blob and have them
probe/attach after the system has finished booting.
Note that this change requires /all/ of the AHB using kernel configurations
to change - so until I drop those changes in, this breaks AHB.
Fear not, I'll do that soon.
TODO:
* the above stuff.
Tested:
* AR9331, carambola 2, loading if_ath / wlan as modules at run time
The latest firmware has a number of link related fixes, support for a
new custom card, and the fix for a bug that affected rate limiting on
FreeBSD.
Obtained from: Chelsio Communications
MFC after: 1 week
Sponsored by: Chelsio Communications
In r315866, we introduced a direct read of the 8-bit sromrev field from the
memory mapped SPROM/OTP device. On OTP devices that require 16-bit access
alignment, this read fails, preventing identification of the SPROM layout.
So, let's perform an aligned read of the combined 16-bit sromrev/crc field
instead.
Approved by: adrian (mentor, implicit)
Extend the ino_t, dev_t, nlink_t types to 64-bit ints. Modify
struct dirent layout to add d_off, increase the size of d_fileno
to 64-bits, increase the size of d_namlen to 16-bits, and change
the required alignment. Increase struct statfs f_mntfromname[] and
f_mntonname[] array length MNAMELEN to 1024.
ABI breakage is mitigated by providing compatibility using versioned
symbols, ingenious use of the existing padding in structures, and
by employing other tricks. Unfortunately, not everything can be
fixed, especially outside the base system. For instance, third-party
APIs which pass struct stat around are broken in backward and
forward incompatible ways.
Kinfo sysctl MIBs ABI is changed in backward-compatible way, but
there is no general mechanism to handle other sysctl MIBS which
return structures where the layout has changed. It was considered
that the breakage is either in the management interfaces, where we
usually allow ABI slip, or is not important.
Struct xvnode changed layout, no compat shims are provided.
For struct xtty, dev_t tty device member was reduced to uint32_t.
It was decided that keeping ABI compat in this case is more useful
than reporting 64-bit dev_t, for the sake of pstat.
Update note: strictly follow the instructions in UPDATING. Build
and install the new kernel with COMPAT_FREEBSD11 option enabled,
then reboot, and only then install new world.
Credits: The 64-bit inode project, also known as ino64, started life
many years ago as a project by Gleb Kurtsou (gleb). Kirk McKusick
(mckusick) then picked up and updated the patch, and acted as a
flag-waver. Feedback, suggestions, and discussions were carried
by Ed Maste (emaste), John Baldwin (jhb), Jilles Tjoelker (jilles),
and Rick Macklem (rmacklem). Kris Moore (kris) performed an initial
ports investigation followed by an exp-run by Antoine Brodin (antoine).
Essential and all-embracing testing was done by Peter Holm (pho).
The heavy lifting of coordinating all these efforts and bringing the
project to completion were done by Konstantin Belousov (kib).
Sponsored by: The FreeBSD Foundation (emaste, kib)
Differential revision: https://reviews.freebsd.org/D10439
ENA is a networking interface designed to make good use of modern CPU
features and system architectures.
The ENA device exposes a lightweight management interface with a
minimal set of memory mapped registers and extendable command set
through an Admin Queue.
The driver supports a range of ENA devices, is link-speed independent
(i.e., the same driver is used for 10GbE, 25GbE, 40GbE, etc.), and has
a negotiated and extendable feature set.
Some ENA devices support SR-IOV. This driver is used for both the
SR-IOV Physical Function (PF) and Virtual Function (VF) devices.
ENA devices enable high speed and low overhead network traffic
processing by providing multiple Tx/Rx queue pairs (the maximum number
is advertised by the device via the Admin Queue), a dedicated MSI-X
interrupt vector per Tx/Rx queue pair, and CPU cacheline optimized
data placement.
The ENA driver supports industry standard TCP/IP offload features such
as checksum offload and TCP transmit segmentation offload (TSO).
Receive-side scaling (RSS) is supported for multi-core scaling.
The ENA driver and its corresponding devices implement health
monitoring mechanisms such as watchdog, enabling the device and driver
to recover in a manner transparent to the application, as well as
debug logs.
Some of the ENA devices support a working mode called Low-latency
Queue (LLQ), which saves several more microseconds. This feature will
be implemented for driver in future releases.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Jakub Palider <jpa@semihalf.com>
Jan Medala <jan@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon.com Inc.
Differential revision: https://reviews.freebsd.org/D10427
Since netfront uses different locks for the RX and TX paths there's no need to
drop the RX lock before calling if_input.
Suggested by: jhb
Tested by: cperciva
Sponsored by: Citrix Systems R&D
MFC with: r318523
When creating EQs to handle CQ completion events for the PF or for
VFs, we create enough EQE entries to handle completions for the max
number of CQs that can use that EQ.
When SRIOV is activated, the max number of CQs a VF (or the PF) can
obtain is its CQ quota (determined by the Hypervisor resource
tracker). Therefore, when creating an EQ, the number of EQE entries
that the VF should request for that EQ is the CQ quota value (and not
the total number of CQs available in the firmware).
Under SRIOV, the PF, also must use its CQ quota, because the resource
tracker also controls how many CQs the PF can obtain.
Using the firmware total CQs instead of the CQ quota when creating EQs
resulted wasting MTT entries, due to allocating more EQEs than were
needed.
MFC after: 3 days
Sponsored by: Mellanox Technologies
e6000sw family automatically reflects PHY status in each port's registers.
Therefore it is not necessary to do a full PHY polling squence, which
results in much quicker operation and much less significant usage of
the SMI bus.
Care must be taken that the resulting ifmedia_active is identical to
what the PHY will compute, or gratuitous link status changes will
occur whenever the PHYs update function is called.
This patch implements above improvement. On the occasion set a pointer to
the proc structure to be part of software context instead of being
a global variable.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: loos
Differential revision: https://reviews.freebsd.org/D10714
Make sure the RX ring lock is only released when the state of the ring is
consistent, or else concurrent calls to xn_rxeof might get an inconsistent ring
state and thus some packets might be processed twice.
Note that this is not very common, and could only happen when an interrupt is
delivered while in xn_ifinit.
Reported by: cperciva
Tested by: cperciva
MFC after: 1 week
Sponsored by: Citrix Systems R&D
For all Marvell devices, MBUS windows configuration is done
in a common place. Only CESA was an exception, so move its
related code from driver to mv_common.c. This way it uses
same proper DRAM information, same as all other interfaces
instead of parsing DT /memory node directly.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: loos
Differential revision: https://reviews.freebsd.org/D10723
Hitherto implementation of PHY polling resulted in a risk of an
endless loop and very high occupation of the SMI bus. Improve the
operation by limiting the polling tries and adding sleepable
pause.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: loos
Differential revision: https://reviews.freebsd.org/D10713
Call disk_gone when the backend switches to the "Closing" state and blkfront
still has pending users. This allows the disk to be detached, and will call
into xbd_closing by itself when the geom layout cleanup has finished.
Reported by: bapt
Tested by: manu
Reviewed by: bapt
Sponsored by: Citrix Systems R&D
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D10772
kern_yield(0) effectively causes the calling thread to be rescheduled
immediately since it resets the thread's priority to the highest possible
value. This can cause livelocks when the pattern
"while (!trylock()) kern_yield(0);" is used since the thread holding the
lock may linger on the runqueue for the CPU on which the looping thread is
running.
MFC after: 1 week
The ccr(4) driver supports use of the crypto accelerator engine on
Chelsio T6 NICs in "lookaside" mode via the opencrypto framework.
Currently, the driver supports AES-CBC, AES-CTR, AES-GCM, and AES-XTS
cipher algorithms as well as the SHA1-HMAC, SHA2-256-HMAC, SHA2-384-HMAC,
and SHA2-512-HMAC authentication algorithms. The driver also supports
chaining one of AES-CBC, AES-CTR, or AES-XTS with an authentication
algorithm for encrypt-then-authenticate operations.
Note that this driver is still under active development and testing and
may not yet be ready for production use. It does pass the tests in
tests/sys/opencrypto with the exception that the AES-GCM implementation
in the driver does not yet support requests with a zero byte payload.
To use this driver currently, the "uwire" configuration must be used
along with explicitly enabling support for lookaside crypto capabilities
in the cxgbe(4) driver. These can be done by setting the following
tunables before loading the cxgbe(4) driver:
hw.cxgbe.config_file=uwire
hw.cxgbe.cryptocaps_allowed=-1
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D10763
This includes NVMe device support and adds support for the following adapters:
SAS 3408
SAS 3416
SAS 3508
SAS 3516
SAS 3616
SAS 3708
SAS 3716
Reviewed by: ken, scottl, asomers, mav
Approved by: ken, scottl, mav
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D10095
Malloc should always return something when M_WAITOK flag is used,
but keep this code and change flag to M_NOWAIT as it is under a lock
(allows for possible future change). Free ifnet structure to avoid
memory leak on failure.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: loos
Differential revision: https://reviews.freebsd.org/D10711
Experimentally we know this value works, but the hardware
may support an even higher value.
PR: 213876
Reported by: J.Catrysse@proximedia.be
MFC after: 1 week
A long long time ago the register keyword told the compiler to store
the corresponding variable in a CPU register, but it is not relevant
for any compiler used in the FreeBSD world today.
ANSIfy related prototypes while here.
Reviewed by: cem, jhb
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D10193
Invoke any identify routines of child drivers during attach before attaching
children, and delete any remaining devices after deleting ports.
MFC after: 1 month
Sponsored by: Chelsio Communications
2. Use sysctls for TRACE_LRO_CNT and TRACE_TSO_PKT_LEN
3. remove unused mtx tx_lock
4. bind taskqueue kernel thread to the appropriate cpu core
5. when tx_ring is full, stop further transmits till at least 1/16th of the Tx Ring is empty. In our case 1K entries. Also if there are rx_pkts to process, put the taskqueue thread to sleep for 100ms, before enabling interrupts.
6. Use rx_pkt_threshold of 128.
MFC after:3 days
sdhci_fdt.
Enable the SDHCI controller, bus and devices on ARMADA38X kernel.
Tested on: ClearFog Pro
Reviewed by: Marcin Wojtas <mw at semihalf.com>
Sponsored by: Rubicon Communications, LLC (Netgate)
Differential Revision: https://reviews.freebsd.org/D10606
Two blocks in e1000_ich8lan.c are misaligned, causing noise with some
compilers (gcc 6).
Reviewed by: imp, erj
Differential Revision: https://reviews.freebsd.org/D10741
and Braswell eMMC and SDXC controllers share the same IDs. Like in
the PCI case, Braswell eMMC needs the SDHCI_QUIRK_DATA_TIMEOUT_1MHZ
quirk (see r311794 for the corresponding change to the sdhci(4) PCI
PCI front-end), though. However, due to the shared ACPI IDs, this
is trickier to do.
- Intel Apollo Lake eMMC and SDXC controllers are affected by the
APL18 ("Using 32-bit Addressing Mode With SD/eMMC Controller May
Lead to Unpredictable System Behavior") silicon bug [1]. When this
erratum hits, typically both SDHCI and XHCI controllers wedge.
According to Intel, using ADMA2 with 64-bit addressing and 96-bit
descriptors serves as a workaround. Until such times when sdhci(4)
has ADMA2 support, flag DMA as broken for affected interfaces.
This turns out to work around the problem, too, at the cost of
performance.
- In the sdhci(4) ACPI front-end, probe the Intel Apollo Lake eMMC
and SDXC controllers, too.
1: http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/pentium-celeron-n-series-j-series-datasheet-spec-update.pdf
* This fixes cases where the group id of wide commands got lost, e.g. this
happened to the IWM_SCAN_ABORT_UMAC command.
Obtained from: dragonflybsd.git 71310fab0caca79bb5da43d9d642e77a4c27eea2
* Since a RUN -> INIT/SCAN transition seems to immediately destroy the
ieee80211_node for the AP, we can't read the in_assoc value from there.
Instead just directly pass that information via a boolean_t argument.
* Adds iwm_mvm_rm_sta_id() function, which just unconditionally removes
the station from the firmware.
* The iwm_mvm_rm_sta() function shouldn't actually remove the station from
firmware when we are still associated (i.e. during a RUN -> INIT/SCAN
transition).
* So when disassociating we will first call iwm_mvm_rm_sta() to drain the
queues/fifos. Later during disassociation we will then use
iwm_mvm_rm_sta_id() to actually remove the station.
Inspired-By: Linux iwlwifi
Obtained from: dragonflybsd.git 81b3c1fe9122fa22f33d97103039cc375f656231
* Add a per-vap ps_disabled flag, and use it for a workaround which fixes
an association issue when powersaving is enabled.
* Compute flag that should correpsond to the mvmif->bss_conf.ps flag in
Linux's iwlwifi (e.g. this disallows powersaving when not associated
yet).
Inspired-By: Linux iwlwifi
Obtained from: dragonflybsd.git dc2e69bdfe8c9d7049c8a28da0adffbfbc6de5c0
* Power management handling is per-vap, not per-node, so we should pass
the iwm_vap in these arguments.
Obtained from: dragonflybsd.git 62a4e7957a736b4de38938b02fa7eb9b45bc5d0d
* Otherwise we would never update powersaving settings until we complete
an association, after the first authentication attempt.
* This corresponds to what Linux iwlwifi seems to do.
Obtained from: dragonflybsd.git aa128dc02a17c2e616232ef0fa997121e969c995
* Tear down the relevant firmware state (i.e. the station, the vif binding)
in these transition cases.
* Before this case would leave the firmware state lying around, resulting
in errors and firmware panics in the subsequent association attempts.
Obtained from: dragonflybsd.git 94b501399fde6368ae388a669c95b099a6e66e93
* This adds iwm_mvm_rm_sta(), which will be used to tear down firmware
state for better/cleaner iwm_newstate() handling.
* Makes iwm_enable_txq() and iwm_mvm_flush_tx_path() non-static, add
the declarations to if_iwm_util.h for now.
Obtained from: dragonflybsd.git 85d1c6190c4c3564b1a347f253e823aa95c202b2
* Hence no need to keep stuff in separate iwm_assoc() function, just
inline the stuff into iwm_newstate().
Obtained from: dragonflybsd.git e8f7d88e0d030f138f95ecdb7c1a729d9fb0d6ab
* Inspired by iwn(4) and Linux iwlwifi.
* Read wme parameters into a buffer within struct iwm_vap in
iwm_wme_update().
* If we aren't associated yet, the new settings will soon be sent
by iwm_mvm_mac_ctxt_changed() during association.
* If we are already associated, explicitly call iwm_mvm_mac_ctxt_changed()
from iwm_wme_update() to send the new settings to the firmware.
* Change iwm_mvm_ac_to_tx_fifo mapping, to fit the freebsd net80211
WME stream class numbering, instead of Linux's enum ieee80211_ac_numbers.
Obtained from: dragonflybsd.git b8bd6cd746d1f45e616ccfcbeed06dfe452a1108
* Factor out iwm_handle_rxb() function from iwm_notif_intr().
* Removing the IWM_FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MSK flag allows
the device to put multiple frames (both command responses and 80211
frames) into a single RX buffer.
* Uses m_copym() to split up the receive buffers when multiple 80211
frames are received in one RX buffer. The effect is basically the same
as when using m_split(), but we want to keep the original mbuf around
when calling iwm_mvm_rx_rx_mpdu() to make error handling a bit easier
for now.
* Contains a small optimization to avoid the m_copym() when only a single
80211 frame is received in one RX buffer (i.e. matching the existing
behaviour).
Obtained from: dragonflybsd.git b5eb43f0280bbcfd26af51cf5a4b8e8ff3590b67
* Fixes oversight from commit 757eecf0e6c92745aa2eee95811e573c8300850e.
fw_has_api now uses the isset macro instead of a simple logical-and.
Obtained from: dragonflybsd.git c00575de8491dc402abf52c8c7e1cca1ef79e257
* Store macid and color values in struct iwm_vap, to avoid hardcoded
constants a bit.
* Add iwm_mvm_binding_remove_vif() function (will be used in disconnecting
from an access point without resetting the whole device).
* Not adding code from Linux iwlwifi yet, to handle one PHY context to
be bound to several VAPs/virtual-interfaces, it's definitely not needed
in the near future.
Obtained from: dragonflybsd.git f16ef74977e51e1bfc7a625dd18b98b02158e0e5
For GEN1 Hyper-V, vmbus is attached to pcib0, which contains the
resources for PCI passthrough and SR-IOV. There is no
acpi_syscontainer0 on GEN1 Hyper-V.
For GEN2 Hyper-V, vmbus is attached to acpi_syscontainer0, which
contains the resources for PCI passthrough and SR-IOV. There is
no pcib0 on GEN2 Hyper-V.
The ACPI VMBUS device now only holds its _CRS, which is empty as
of this commit; its existence is mainly for upward compatibility.
Device tree structure is suggested by jhb@.
Tested-by: dexuan@
Collabrated-wth: dexuan@
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D10565
controllers that do not support or have broken ACMD12 implementations.
Reviewed by: jmcneill
Obtained from: NetBSD
MFC after: 2 weeks
Sponsored by: Rubicon Communications, LLC (Netgate)
Differential Revision: https://reviews.freebsd.org/D10602
- Do not leak the adapter lock in sysctl_autoneg.
- Accept only 0 or 1 as valid settings for autonegotiation.
- A fixed speed must be requested by the driver when autonegotiation is
disabled otherwise the firmware will reject the l1cfg command. Use
the top speed supported by the port for now.
MFC after: 3 days
Sponsored by: Chelsio Communications
This might improve throughput slightly when far from the accesspoint,
apparently by allowing the firmware to listen on either of the two
antennas (if there are two, i.e. on 7260/7265/8260), whichever has
a better reception.
Obtained from: dragonflybsd.git 3b7fc5aac51f81062da0a2c8fdac23e683fbd548
* The DEVICE_POWER_FLAGS_CAM_MSK flag was removed in the upstream iwlwifi
in Linux commit ceef91c89480dd18bb3ac51e91280a233d0ca41f.
* Add sc_ps_disabled flag to struct iwm_softc, which corresponds to
mvm->ps_disabled in struct iwl_mvm in Linux iwlwifi.
* Adds a hw.iwm.power_scheme tunable which corresponds to the power_scheme
module parameter in Linux iwlwifi. Set this to 1 for completely
disabling power management, 2 (default) for balanced powermanagement,
and 3 for lowerpower mode (which does dtim period skipping).
* Imports the constants.h file from iwlwifi as if_iwm_constants.h.
* This doesn't allow changing the powermanagement setting while connected,
also one can only choose between enabled and disabled powersaving with
ifconfig (so switching between balanced and low-power mode requires
rebooting to change the tunable).
* After any changes to powermanagement (i.e. "ifconfig wlan0 powersave" to
enable powermanagement, or "ifconfig wlan0 -powersave" for disabling
powermanagement), one has to disconnect and reconnect to the accespoint
for the change to take effect.
Obtained from: dragonflybsd.git d7002a7990d077c92585978ea998474af50f91e0
* Fix a couple of cases where the nic lock ended up not being grabbed
during an iwm_read_prph() or iwm_write_prph().
Obtained from: dragonflybsd.git 6c5470f2db219c61e362c981fea969d97e1b8293
* Target module have ic plus etherswitch ip175c.
* Also add etherswitch support code on rt driver.
Reviewed by: mizhka
Differential Revision: https://reviews.freebsd.org/D10336
Add workaround mii access because of rt1310 is hang up on etherswitch mii poll.
And FDT away on arm platform.
Tested:
* wzr2-g300n
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Reviewed by: mizhka
Differential Revision: https://reviews.freebsd.org/D10295
the TOE. For now this capability is always enabled in kernels with
options RATELIMIT. t4_tom will check if_capenable once the base driver
gets code to support rate limiting for any socket (TOE or not).
This was tested with iperf3 and netperf ToT as they already support
SO_MAX_PACING_RATE sockopt. There is a bug in firmwares prior to
1.16.45.0 that affects the BSD driver only and results in rate-limiting
at an incorrect rate. This will resolve by itself as soon as 1.16.45.0
or later firmware shows up in the driver.
Relnotes: Yes
Sponsored by: Chelsio Communications
Increase hw.psm.synaptics.min_pressure default value from 16 to 32
to nearly match Linux driver (30-35 hysteresis loop).
This makes libinput tap detection more reliable.
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
It is already included via sys/systm.h
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
models. This change is based on Linux driver.
Determine logical trace size. It used for calculation of touch sizes
in surface units for MT-protocol type B evdev reports.
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
Linux does. It should not affect gesture processing in current state as it
ignores finger coords on 3-finger tap detection but it should make evdev
reports looking more Linux-alike.
Reviewed by: gonzo
Approved by: gonzo
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
This is done with discarding pointer movements rather then mouse packets
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
Elan hw v.4 touchpads often sends touchpad release packet right after
touchpad touch one. Most probably this happens due to PS/2 limited bandwith.
Reducing of tap_min_queue size to 1 makes multifinger tap detection
more reliable in this case.
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
Wait for all advertised head packets after status packet have been received.
This fixes rare but quite annoying issue in Elan hw v.4 touchpads support
when triple-finger taps are reported as double-finger taps under several
circumstances.
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
races at least in its ioctl handler, and at the same time it creates
device entry with 0666 permissions.
To plug possible issues in it:
- Mark it as needing Giant.
- Switch device mode to 0600.
Submitted by: C Turt
Reviewed by: imp
MFC after: 1 week
Security: Possible double free in ioctl handler
Prior to this change, the CRN (Command Reference Number) is reset on any
firmware LIP, LOOP DOWN, or LOOP RESET event in violation of FCP-4 which
specifies that the CRN should only be reset in response to a LIP Reset
(LIPyx) primitive. FCP-4 also indicates PLOGI/LOGO and PRLI/PRLO ELS
actions as conditions for resetting the CRN for the associated initiator
port.
These violations manifest themselves when the HBA is removed from the
loop, or a target device is removed (especially during an outstanding
command) without power cycling. If the HBA and and the target device
determine upon re-establishing the loop that no PLOGI or PRLI is
required, and the target does not issue a LIPxy to the initiator, the
CRN for the target will have been improperly reset by the isp driver. As
a result, the target port will silently ignore all FCP commands issued
during the device probe (which will time out) preventing the device from
attaching.
This change corrects thie CRN reset behavior in response to loop state
changes, also introduces CRN resets for the above mentioned ELS actions
as encountered through async PDB change events.
This change also adds cleanup of outstanding commands in isp_loop_dead()
that was previously missing.
sys/dev/isp/isp.c
Add the last login state to debug output when syncing the pdb
sys/dev/isp/isp_freebsd.c
Replace binary statement setting aborted ccb status in
isp_watchdog() with the XS_SETERR macro used elsewhere
In isp_loop_dead(), abort or complete pending commands as done
in isp_watchdog()
In isp_async(), segregate the ISPASYNC_LOOP_RESET action from
ISPASYNC_LIP, ISPASYNC_LOOP_DOWN, and ISPASYNC_LOOP_UP
fallthroughs, and only reset the CRN in the RESET case. Also add
checks to handle false LOOP RESET actions that do not have a
proper associated LIP primitive, and log the primitive in the
debug messages
In isp_async(), remove the goto from ISP_ASYNC_DEV_STAYED, and
only reset the CRN in the DEV_CHANGED action
In isp_async(), when processing an ISPASYNC_CHANGE_PDB status,
reset CRN(s) for the associated nphdl (or all ports) if the
change reason is some form of ELS login/logout. Also remove
assignment to fc since it is not used in the scope
sys/dev/isp/ispmbox.h
Add macro definition for the global N-Port handle, and correct a
macro typo 'PDB24XX_AE_PRLI_DONJE'
sys/dev/isp/ispvar.h
Add macros FCP_AL_DA_ALL, FCP_AL_PA, and FCP_IS_DEST_ALPD for
more legible code when determining if an AL_PD port matches the
portid for a given struct fcparam* by value or by virtue of the
AL_PD port being 0xFF
Submitted by: Reid Linnemann
Sponsored by: Spectra Logic
MFC after: 1 week
- Create a new file, t4_sched.c, and move all of the code related to
traffic management from t4_main.c and t4_sge.c to this file.
- Track both Channel Rate Limiter (ch_rl) and Class Rate Limiter (cl_rl)
parameters in the PF driver.
- Initialize all the cl_rl limiters with somewhat arbitrary default
rates and provide routines to update them on the fly.
- Provide routines to reserve and release traffic classes.
MFC after: 1 month
Sponsored by: Chelsio Communications
At least with Tx FIFO enabled it shows me ~10% reduction of verbose boot
time with serial console at 115200 baud.
Reviewed by: marcel
MFC after: 2 weeks
