the link and activity LED control bits in CSR15 in order for the
controller to drive the LEDs correctly. This was largely done for the
ZNYX multiport cards, but should also work with the DEC DE500-BA
and other non-MII cards.
enable bit hasn't been set in the command register, set the bit and
honour the register. It seems that quite a few lazy BIOS writers
aren't bothering to do this, which upsets the existing code and causes
us to miss out on properly-configured devices.
pcib instance is initialized because accesses to PCI_Config region can
occur during ACPI initialization.
Note that this is a short term solution, more consideration will be
required in order to integrate ACPI into the newbus probe sequence.
change channel interface - kobj implementation coming soonish
make pcm_makelinks not panic if modular
add pcm_unregister()
these changes support newpcm kld unloading, but this is only implemented
by ds1.c
This provides support for the Adaptec SCSI RAID controller family,
as well as the DPT SmartRAID V and VI families.
The driver will be maintained by Mark and Adaptec, and any changes
should be referred to the MAINTAINER.
- Remove DELAY() kludge before power off.
- Move EVENTHANDLER_REGISTER to acpi_attach().
- Pass RB_POWEROFF flag to shutdown_nice().
Reviewed by: msmith
kernel can instigate an orderly shutdown but still determine the form of
that shutdown. Make it possible eg. to cleanly shutdown and power off the
system under ACPI when the power button is pressed.
- New support for 40LD firmware found in Series 475 and 471 adapters.
- Better support for 8LD firmware adapters
- Ioctl passthrough interface for userland utilities.
- Improved error handling and queueing.
- Several bugfixes (including the 'still open' shutdown bug and
closing some small race conditions).
- Zone-style command allocator, reducing memory wasted under heavy
load conditions.
- CAM interface (disabled and not fully working) for SCSI passthrough
access to non-disk devices
Thanks to AMI for supplying a pile of new adapters and various other
help in making this happen.
- Add new funcions for device state stuff;
acpi_get_current_device_state() and acpi_set_device_state()
- Add new funcions for power resource stuff;
acpi_powerres_init(), acpi_powerres_debug(),
acpi_get_current_powerres_state() and acpi_set_powerres_state()
These were implemented based on 7.1, 7.2, 7.2.2, 7.2.3, 7.2.4, 7.3,
7.3.3, 7.4, 7.4.1, 7.4.2, 7.4.3 and 7.5 of ACPI spec 1.0b.
- The "Osd*" stuff went away from acpi driver code, use the bus_space
functions directly instead.
- Fix minor english bugs.
acpi_registers_input -> acpi_register_input
acpi_registers_output -> acpi_register_output
- Remove all magic numbers for the sleeping states. We now have
#defines for these.
- NULL is treated the same as the return from aml_get_rootname in
aml_find_from_namespace().
Suggested by: msmith
Thanks mike!
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
possible complications with the forthcoming DRI code, and feel that DRI
should handle the device-level interaction. Read
http://people.FreeBSD.org/~cokane/3dfx.html
to find out more. Basically want to move toward using OpenGL and DRI for
everything on these cards. Added a few defines and spacing style fixes in
tdfx_vars.h
o Sync to NetBSD (rev NetBSD-user edited-log):
1.97 onoe add Samsung MagicLAN SWL-2000N
1.96 gmcgarry Add entries for all Xircom ethernet models.
1.95 onoe Add Farallon SkyLINE 11mb card as Intersil Prism2 [...]
1.94 joda add 3Com 3CRWE737A (AirConnect)
1.93 soren Include vendor name for IBM products.
1.92 onoe Add Farallon SkyLINE Wireless LAN Card for awi(4) [...]
1.91 soren Add Olicom GoCard.
1.90 gmcgarry Clean up XIRCOM entries
- Add entry for Xircom CreditCard Ethernet + Modem 28
- Add entry for Intel EtherExpress PRO/100
- Add entry for Compaq Netelligent 10/100 Ethernet
1.89 is RATOC REX-R280 (another if_mbe_pcmcia card) support by [...]
1.88 joda Panasonic KXLC003
1.87 scw [...] SOHOware PCMCIA Ethernet card, model ND5100-E [...]
1.86 itojun add CIS for Corega Wireless LAN PCC-11 [...]
o Minor diffs between the two files corrected to aid future sync.
modify driver capability reporting format to list every audio format
seperately- required for above and because we could not previously indicate
that mono was unsupported.
there should be no functional impact.
Remove old DEVFS support fields from dev_t.
Make uid, gid & mode members of dev_t and set them in make_dev().
Use correct uid, gid & mode in make_dev in disk minilayer.
Add support for registering alias names for a dev_t using the
new function make_dev_alias(). These will show up as symlinks
in DEVFS.
Use makedev() rather than make_dev() for MFSs magic devices to prevent
DEVFS from noticing this abuse.
Add a field for DEVFS inode number in dev_t.
Add new DEVFS in fs/devfs.
Add devfs cloning to:
disk minilayer (ie: ad(4), sd(4), cd(4) etc etc)
md(4), tun(4), bpf(4), fd(4)
If DEVFS add -d flag to /sbin/inits args to make it mount devfs.
Add commented out DEVFS to GENERIC
that should be better.
The old code counted references to mbuf clusters by using the offset
of the cluster from the start of memory allocated for mbufs and
clusters as an index into an array of chars, which did the reference
counting. If the external storage was not a cluster then reference
counting had to be done by the code using that external storage.
NetBSD's system of linked lists of mbufs was cosidered, but Alfred
felt it would have locking issues when the kernel was made more
SMP friendly.
The system implimented uses a pool of unions to track external
storage. The union contains an int for counting the references and
a pointer for forming a free list. The reference counts are
incremented and decremented atomically and so should be SMP friendly.
This system can track reference counts for any sort of external
storage.
Access to the reference counting stuff is now through macros defined
in mbuf.h, so it should be easier to make changes to the system in
the future.
The possibility of storing the reference count in one of the
referencing mbufs was considered, but was rejected 'cos it would
often leave extra mbufs allocated. Storing the reference count in
the cluster was also considered, but because the external storage
may not be a cluster this isn't an option.
The size of the pool of reference counters is available in the
stats provided by "netstat -m".
PR: 19866
Submitted by: Bosko Milekic <bmilekic@dsuper.net>
Reviewed by: alfred (glanced at by others on -net)
has the side effect of detaching the children before I delete them.
When I put the last commits in a loop for loop it died after 5 or so
iterations. After this change, I lasted 50 before I stopped the test.
Add pcic_detach which removes all of the pcic's children.
This lets me load/unload pcic multiple times w/o having multiple
instances of each slot attached to pcic.
problems). Also pick an irq if one isn't specified. Ditto for
memory.
Add additional printfs in the error paths. These will disappear in time.
There are still some panics, but this is a good checkpoint.
some of the fake devices sometimes seen on single device ATA
channels.
Proberly fail on failures in ata-disk.c, retry instead of hang.
Cleanup the VIA probe/init code a bit.
Fix a couble of missing free's in atapi-cd.c in the changer code.
Add support for AMD RAID controllers as "disks".
Requested-by: Marius Bendiksen <mbendiks@eunet.no>
Remove potential panic when attempting to open non-existent drivers.
init_drive: Return error codes correctly. Previously it would
occasionally return 0. The error was redetected
elsewhere, but this was causing a number of confusing
error messages.
Add support for wi(4) compatible configuration interface. It enables
wicontrol(8) to configure some 802.11 specific parameters.
Some minor fixes from NetBSD.
Obtained from: NetBSD current
in bogus hwptr warnings. Further comments sought on -hackers
were not forthcoming. I can only hope that calling DELAY() like
this doesn't cause any heartburn.
Make the umass driver depend on this module.
Makes it possible to compile the kernel without SCSI support and load it
when for example a USB floppy is conencted.
Make it possible to move a device to its unconfigured state by
using config #0.
Add some comments.
Change error reporting in port reset function.
usbd_devinfo_vp(): search the know devs array also if the device doesn't
return product description (e.g. Kye's Genius NetScroll mouse returns
vendor, but not product); the strings returned by device are still
preferred to those in the array, though
understand exactly what it is about SMPng that tickles this bug. What I
do know is that the foo_init() routine in most drivers is often called
twice when an interface is brought up. One time is due to the ifconfig(8)
command calling the SIOCSIFFLAGS ioctl to set the IFF_UP flag, and another
is probably due to the kernel calling ifp->if_init at some point. In any
case, the SMPng changes seem to affect the timing of these two events in
such a way that there is a significant delay before any packets are sent
onto the wire after the interface is first brought up. This manifested
itself locally as an SMPng test machine which failed to obtain an address
via DHCP when booting up.
It looks like the second call to fxp_init() is happening faster now than
it did before, and I think it catches the chip while it's in the process
of dealing with the configuration command from the first call. Whatever
the case, a FXP_CSR_SCB_CNA interrupt event is now generated shortly after
the second fxp_init() call. (This interrupt is apparently never generated
by a non-SMPng kernel, so nobody noticed.)
There are two problems with this: first, fxp_intr() does not handle the
FXP_CSR_SCB_CNA interrupt event (it never tests for it or does anything
to deal with it), and second, the meaning of FXP_CSR_SCB_CNA is not
documented in the driver. (Apparently it means "command unit not active.")
Bad coder. No biscuit.
The fix is to have the FXP_CSR_SCB_CNA interrupt handled just like the
FXP_SCB_STATACK_CXTNO interrupt. This prevents the state machine for
the configuration/RX filter programming stuff from getting wedged for
several seconds and preventing packet transmission.
Noticed by: jhb
This is done by misusing the device minor a bit to encode the
track no there.
So to read track #4 just use /dev/acdNt4 where N is the device #.
The driver no automatically sets the blocksize (sectorsize) to
what the track is set to in the TOC.
This has the nice effect that you can now rip audioi tracks
by simply doing:
dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352
it cant be much simpler than that :)
NOTE: the original acdNa & acdNc device still work as usual,
except the blocksize is set according to track0.
from the SCSI id it has. (this avoids the confusing umass-sim32 device. It
should have been umass-sim0 all along (there is only one), and if it is
spoken to as a SCSI device the sim should be umass32.
Make the rescan actually work. We need to fill in a target and lun wildcard
and not the SCSI id of the SIM.
Add a seatbelt.
position, channel 1's dma position register must be quiescent. So
the driver will spl, pause the DMA, delay a bit and hold as still as
possible while snapping the picture.
I'm sure there HAS to be a better way to do this, but if there is, it's
not documented.
So far as I can tell, this fixes recording, which means the Solo is open
for business.
cases the registers are not correctly set on resume.
This solves the problem of USB failing after resuming a machine.
Submitted by: mike+fbsd@medianstrip.net
PR: 18261
Promise Ultra100 / Fasttrak100
HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100)
Intel ICH2 (Intel 815E based motherboards)
So far I can read >90MB/s on the Promise and the HPT370.
I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems
writing is still done in ATA66 mode :(
The ICH2 support is untested as of yet...
modules to depend on modules in the same file (uhub depends on usb) or
even on themselves (usb on usb, makes the define in usb_port.h a lot
less convoluted).
Use ANSI prototypes.
the scratch RAM for data normally found in the SEEPROM (presumably in the
event that the SEEPROM is unavailable or can't be read). This code causes
a spontaneous reboot on monster.osd.bsdi.com, which has an embedded aic7880
controller. The problem appears to happen either when it writes to the
SCBPTR port and then reads from the SCB_CONTROL port. Somewhere during
the inb/outb operations, the system has a heart attack and restarts.
This code looks very suspicious, particularly since it has unconditionalized
debug mesages such as "Got here!" and "And it even worked!". With this
block #ifdef'ed out, the machine boots and runs properly. I stronly suggest
that it stay #ifdef'ed out until it's properly tested.
opens if the reference count is not decremented on close.
Note that this may result in the reference count being corrupted
on full duplex devices (due to mismatching opens/closes), but the
code doesn't use the reference count for anything on full duplex
devices.
2. Offer half duplex with both playback and record on channel 1 or
full duplex with playback always on channel 2 as a compile-time option.
3. 16 bit record output is byte swapped for some dumb reason. Report the _BE
AFMTs for recording.
if you kldload this driver, all the subordinate devices are probed/attached
as expected. But this is not the case when the driver is statically compiled
into the kernel. Since I do most of my testing with modules, I failed to
notice this. I'm not sure if it's intended behavior or not. I think it may
be, but it seems a little counter-intuitive.
16 bit samples have some sort of choppiness, the nature of which
is not completely clear, but it clearly has something to do with
dma buffer synchronization. But at least channel 1 makes noise now.
appears to be the correct length, but quality of output has not yet
been tested. Also, full duplex audio (that is, playback on channel 1)
does not yet work. Two constants and I am there!
Obtained from: major hints from ALSA
with LEDs on some cards being stomped on when clearing the "jabber disable"
bit. Using DC_SETBIT() has an unwanted side effect of setting a write enable
bit in the watchdog timer register which we really want to be cleared when
we do a write.
changes is that there's now a Solaris port of this driver, so some things
in the core version had to change (not much, but some).
In order, from the top.....:
A lot of error strings are gathered in one place at the head of the file.
This caused me to rewrite them to look consistent (with respect to
things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'.
The major mailbox function, isp_mboxcmd, now takes a third argument,
which is a mask that selectively says whether mailbox command failures
will be logged. This will substantially reduce a lot of spurious noise
from the driver.
At the first run through isp_reset we used to try and get the current
running firmware's revision by issuing a mailbox command. This would
invariably fail on alpha's with anything but a Qlogic 1040 since SRM
doesn't *start* the f/w on these cards. Instead, we now see whether we're
sitting ROM state before trying to get a running BIOS loaded f/w version.
All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to
isp_prt. There are seperate print levels that can be independently
set (see ispvar.h), which include debugging, etc.
All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and
RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel
cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry
indices, so we can make a 1024 entry index for them instead of the
256 entries we've had until now.
A major change it to fix isp_fclink_test to actually only wait the
delay of time specified in the microsecond argument being passed.
The problem has always been that a call to isp_mboxcmd to get he
current firmware state takes an unknown (sometimes long) amount of
time- this is if the firmware is busy doing PLOGIs while we ask
it what's up. So, up until now, the usdelay argument has been
a joke. The net effect has been that if you boot without being plugged
into a good loop or into a switch, you hang. Massively annonying, and
hard to fix because the actual time delta was impossible to know
from just guessing. Now, using the new GET_NANOTIME macros, a precise
and measured amount of USEC_DELAY calls are done so that only the
specified usecdelay is allowed to pass. This means that if the initial
startup of the firmware if followed by a call from isp_freebsd.c:isp_attach
to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000,
no more than two seconds will actually elapse before we leave concluding
that the cable is unhooked. Jeez. About time....
Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE
macro to a call to the platform supplied isp_done (sane naming).
Limit our size of request queue completions we'll look at at interrupt
time. Since we've increased the size of the Request Queue (and the
size of the Response Queue proportionally), let's not create an
interrupt stack overflow by having to keep a max completion list
(forw links are not an option because this is common code with
some platforms that don't have link space in their XS_T structures).
A limit of 32 is not unreasonable- I doubt there'd be even this many
request queue completions at a time- remember, most boards now use
fast posting for normal command completion instead of filling out
response queue entries.
In the isp_mboxcmd cleanup, also create an array of command
names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8".
Remove the isp_lostcmd function- it's been deprecated for a while.
Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus
register dump fucntion.
Various other cleanups.
isp_prt calls. We now use an argument to the ISPCTL_FCLINK_TEST
call. We change all IDPRINTF macros to isp_prt calls. We add
the isp_prt function here.
quite a bit so that all of the ports have a similar set of required
macros/definitions (and in similar places in the isp_<platform>.h
file).
Some new macros/functions added- Mailbox Acquire/Relase macros,
NANOTIME macros, SNPRINTf and STRNCAT. MemoryBarrier beomes
MEMORYBARRIER with much stronger types.
isp2100_fw_statename as an INLINE (now a function in isp.c). Remove
isp2100_pdb_statename (unused). Redo all ISP_SCSI_XFER_T as XS_T types.
Change all RQUEST_QUEUE_LEN/RESULT_QUEUE_LEN macros to take a parameter.
Add isp_print_bytes function.
Disable "cache line streaming" for aic7890/91 Rev A chips. I
have never seen these chips fail using this feature, but
some of Adaptec's regression tests have.
Explicitly set "cache line streaming" to on for aic7896/97
chips. This was happening before, but this documents the
fact that these chips will not function correctly without
CACHETHEEN set.
aic7xxx.h:
Add new bug types.
Fix a typo in a comment.
aic7xxx.reg:
Add a definition for the SHVALID bit in SSTAT3 for Ultra2/3
chips. This bit inicates whether the bottom most (current)
element in the S/G fifo has exhausted its data count.
aic7xxx.seq:
Be more careful in how we turn off the secondary DMA channel.
Being less careful may hang the PCI bus arbitor that negotiates
between the two DMA engines.
Remove an unecessary and incorrect flag set operation in
the overrun case.
On Ultra2/3 controllers, clear the dma FIFO before starting
to handle an overrun. We don't want any residual bytes from
the beginning of the overrun to cause the code that shuts
down the DMA engine from hanging because the FIFO is not
(and never will be) empty.
If the data fifo is empty by the time we notice that a
read transaction has completed, there is no need to
hit the flush bit on aic7890/91 hardware that will not
perform an auto-flush. Skip some cycles by short circuiting
the manual flush code in this case.
When transitioning out of data phase, make sure that we
have the next S/G element loaded for the following
reconnect if there is more work to do. The code
would do this in most cases before, but there was
a small window where the current S/G element could
be exhausted before our fetch of the next S/G element
completed. Since the S/G fetch is already initiated
at this point, it makes sense to just wait for the
segment to arrive instead of incuring even more latency
by canceling the fetch and initiating it later.
Fast path the end of data phase handling for the last
S/G segment. In the general case, we might have
worked ahead a bit by stuffing the S/G FIFO with
additional segments. If we stop before using them
all, we need to fixup our location in the S/G stream.
Since we can't work past the last S/G segment, no
fixups are ever required if we stop somewhere in
that final segment.
Fix a little buglet in the target mode dma bug handler.
We were employing the workaround in all cases instead
of only for the chips that require it.
Fix the cause of SCB timeouts and possible "lost data"
during read operations on the aic7890. When sending
a data on any Ultra2/3 controller, the final segment
must be marked as such so the FIFO will be flushed and
cleaned up correctly when the transfer is ended. We
failed to do this for the CDB transfer and so, if
the target immediately transfered from command to data
phase without an intervening disconnection, the first
segment transferred would be any residual bytes from
the cdb transfer. The Ultra160 controllers for some
reason were not affected by this problem.
Many Thanks to Tor Egge for bringing the aic7890 problem
to my attention, providing analysis, as well as a mechanism
to reproduce the problem.
stored at a different location in the PCI space, so adjust accordingly.
Also, when using more than two smart controllers in one machine, the
disks were assigned the wrong drive number; fix this as well.
the 12.4.11 firmware with a few changes to the link handling code merged
in from the 12.4.13 release. I'm doing this because the 12.4.13 firmware
doesn't seem to handle 10/100 link settings properly on 1000baseT cards.
Note that the revision codes still identify the firmware as 12.4.13
because both ti_fw2.h and ti_fw.h have to have the same revision values,
and I wanted to keep the 12.4.13 firmware for Tigon 1 cards.
It's nice to have firmware source.
wrong bytes.
o Improve the public interface; use void* instead of char* or u_int64_t
to pass arbitrary data around.
Submitted by: kris ("horrible bug")
didn't bother to send a saved data pointers after the last transfer,
is not recorded in sgptr. This was only a problem if the target
reported non-zero status as we always check the residual in that case.
Correct the BUILD_TCL macro. It was placing the target id
in the wrong bits. This was only an issue for adapters that
do not perform SCB paging (aha-3940AUW for instance).
Don't bother inlining ahc_index_busy_tcl. It is never
used in a performance critical path and is a bit chunky.
Correct ahc_index_busy_tcl to deal with "busy target tables"
embedded in the latter half of 64byte SCBs.
Don't initialize the busy target table to its empty state
until after we have finished extracting configuration
information from chip SRAM. In the common case of using
16 bytes of chip SRAM to do untagged target lookups,
we were trashing the last 8 targets configuration data.
(actually only target 8 because of the bug in the
BUILD_TCL macro).
Cram the "bus reset delivered" message back under bootverbose.
Fix the cleanup of the SCB busy target table when aborting
commands. If the lun is wildcarded, we must loop through
all possible luns.
aic7xxx.h:
Only bother supporting 64 luns right now. It doesn't seem
like either this driver or any peripherals will be doing
information unit transfers (where the lun number is a
32 bit integer) any time soon.
aic7xxx.seq:
Fix support for the aic7895. We must flush the data
FIFO if performing a manual transfer that is not
a multiple of 8 bytes. We were doing this quite
regularly for embedded cdbs.
Manaually flush the fifo on earlier adapters when
dealing with embedded cdbs too. We were stuffing
the FIFO with 16 bytes instead, but triggering
the flush is more efficient and allows us to
remove two instructions from the "copy_to_fifo"
routine.
o Make the comments KNF-compliant.
o Use nanotime instead of getnanotime; the manpage lies about the
kern.timecounter.method - it has been removed.
o Fix the ENTROPYSOURCE const permanently.
o Make variable names more consistent.
o Make function prototypes more consistent.
Some more needs to be done; to follow.
cards. This basically involves switching to the 12.4.13 firmware, plus
a couple of minor tweaks to the driver.
Also changed the jumbo buffer allocation scheme just a little to avoid
'failed to allocate jumbo buffer' conditions in certain cases.
support for relocating the port address if the isa hints specify a
different address from the address the chipset currently has.
Submitted by: Andrew M. Miklic <miklic@ibm.net>
lock up under moderate to heavy load.
The status & command fields share a 32-bit longword. The programming
API of the eepro apparently requires that you update the command field
of a transmit slot that you've already given to the card. This means
the card could be updating the status field of the same longword at
the same time. Since alphas can only operate on 32-bit chunks of
memory, both the status & command fields are loaded from memory &
operated on in registers when the following line of C is executed:
sc->cbl_last->cb_command &= ~FXP_CB_COMMAND_S;
The race is caused by the card DMA'ing up the status at just the wrong
time -- after it has been loaded into a register & before it has been
written back. The old value of the status is written back, clobbering
the status the card just DMA'ed up. The fact that the card has sent
this frame is missed & the transmit engine appears to hang.
Luckily, as numerous people on the freebsd-alpha list pointed out, the
load-locked/store-conditional instructions used by the atomic
functions work with respect changes in memory due to I/O devices. We
now use them to safely update the command field.
Tested by: Bernd Walter <ticso@mail.cicely.de>
errors that plagued those cards with XFree86 4.0. They have two memory
ranges as well as an IO port range to them. Also cleaned up the three
warning messages that I got, from inb(), outb() and linuxulator. Also, I
noticed that the DRI and Glide support for the Voodoo4 and 5 has been
placed upon linux.3dfx.com, too bad they haven't released the tech docs
yet. Apparently, they are still pushing glide for all of us, so I will try
and add support once those tech docs are up.
other systems.
o Normalize copyright text.
o Clean up probe code function interfaces by passing around a single
structure of common arguments instead of passing "too many" args
in each function call.
o Add support for the AAA-131 as a SCSI adapter.
o Add support for the AHA-4944 courtesy of "Matthew N. Dodd" <winter@jurai.net
o Correct manual termination support for PCI cards. The bit definitions
for manual termination control in the SEEPROM were incorrect.
o Add support for extracting NVRAM information from SCB 2 for BIOSen
that use this mechanism to pass this data to OS drivers.
o Properly set the STPWLEVEL bit in PCI config space based on the
setting in an SEEPROM.
o Go back to useing 32byte SCBs for all controllers. The current
firmware allows us to embed 12byte cdbs on all controllers in
a 32byte SCB, and larger cdbs are rarely used, so it is a
better use of this space to offer more SCBs (32).
o Add support for U160 transfers.
o Add an idle loop executed during data transfers that prefetches
S/G segments on controllers that have a secondary DMA engine
(aic789X).
o Improve the performance of reselections by avoiding an extra
one byte DMA in the case of an SCB lookup miss for the reselecting
target. We now keep a 16byte "untagged target" array on the card
for dealing with untagged reselections. If the controller has
external SCB ram and can support 64byte SCBs, then we use an
"untagged target/lun" array to maximize concurrency. Without
external SCB ram, the controller is limited to one untagged
transaction per target, auto-request sense operations excluded.
o Correct the setup of the STPWEN bit in SXFRCTL1. This control
line is tri-stated until set to one, so set it to one and then
set it to the desired value.
o Add tagged queuing support to our target role implementation.
o Handle the common cases of the ignore wide residue message
in firmware.
o Add preliminary support for 39bit addressing.
o Add support for assembling on big-endian machines. Big-endian
support is not complete in the driver.
o Correctly remove SCBs in the waiting for selection queue when
freezing a device queue.
o Now that we understand more about the autoflush bug on the
aic7890, only use the workaround on devices that need it.
o Add a workaround for the "aic7890 hangs the system when you
attempt to pause it" problem. We can now pause the aic7890
safely regardless of what instruction it is executing.
allocate a short port range in some alpha configurations.
Submitted by: "Andrew M. Miklic" <miklic@udlkern.fc.hp.com>,
Mark Abene <phiber@radicalmedia.com>
when we're done reading it (makes checking things easier).
Before calling isp_notify_ack make sure we're at RUNSTATE-
elsewise we can be responding to LIPs or SCSI bus resets
before we've finished some of the wiring.
we need a function that tells the Qlogic f/w that a target mode command
is done, so increase the resource count for that lun. Add in a timeout
function to kick the putback again if we fail to do it the first time (we
may not have the request queue space for ATIO push). Split the function
isp_handle_platform_ctio into two parts so that the timeout function for
the ATIO push or isp_handle_platform_ctio can inform CAM that the requested
CTIO(s) are now done.
Clean up (cough) residual handling. What we need for Fibre Channel
is to preserve the at_datalen field from the original incoming ATIO
so we can calculate a 'true' residual. Unfortunately, we're not
guaranteed to get that back from CAM. We'll *try* to find it hiding
in the periph_priv field (layering violation)- but if an ATIO was
passed in from user land- forget it. This means that we'll probably
get residuals wrong for Fibre Channel commands we're completing
with an error. It's too late to 4.1 release to fix this- too bad.
Luckily the only device we'd really care about this occurring on
is a tape device and they're still so rare as FC attached devices
that this can be considered an untested combination anyway.
Remove all CCINCR usage (resource autoreplenish). When we've proved
to ourself that things are working properly, we can add it back
in.
Make sure we propage 'suggested' sense data from the incoming ATIO
into the created system ATIO- and set sense_len appropriately.
Correctly propagate tag values.
Fall back to the model of generating (well, the functions in isp_pci.c
do the work) multiple CTIOs based upon what we get from XPT. Instead
of being able to pair Qlogic generated ATIOs with CAM ATIOs, and then
to pair CAM CTIOs with Qlogic CTIOs, we have to take the CTIO passed
to us from XPT, and if it implies that we have to generate extra
Qlogic CTIOs, so be it. This means that we have to wait until the
last CTIO in a sequence we generated completes before calling xpt_done.
Executive summary- target mode actually now pretty much works well
enough to tell folks about.
There is a number of devices that are compliant, of which the 3Com 5605 is
has been verified to work.
The driver is not perfect yet, but should be able to get you somewhere.
The driver was originally written by Lennart Augustsson, but Mike Smith
and Mike Meyer <mwm@mired.org> did the porting.
3.3volt PCI/cardbus chipsets similar to the 98715 (and they have
512-bit hash tables). Also update the man page to mention the 98727/98732
and the SOHOware SFA110A Rev B4 card with the 98715AEC-C chip.
entropy estimation, but causes an immediate reseed after the input
(read in sizeof(u_int64_t) chunks) is "harvested".
This will be used in the reboot "reseeder", coming in another
commit. This can be used very effectively at any time you think
your randomness is compromised; something like
# (ps -gauxwww; netstat -an; dmesg; vmstat -c10 1) > /dev/random
will give the attacker something to think about.
non-disconnecting command. Interestingly enough, of the other flavors
of the 7.65 f/w (the dual-id and multi-id flavor)- the dual-id doesn't
hang (they're also supposed to be the same except for supporting dual
or multi-id capture!), but other things are questionable as well.
which differ slightly from the Macronix MX98715AEC chip on the sample
adapter that I have in that the multicast hash table is only 128 bits
wide instead of 512. New adapters are popping up with this chip, and
due to improper handling of the smaller hash table, broadcast packets
were not being received correctly.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
associated patch to XFree86 allows the X server to work with this chipset
on FreeBSD. Additional work will include porting the Linux 3D driver.
Submitted by: Ruslan Ermilov <ru@FreeBSD.org>
the gating of system calls that cause modifications to the underlying
filesystem. The gating can be enabled by any filesystem that needs
to consistently suspend operations by adding the vop_stdgetwritemount
to their set of vnops. Once gating is enabled, the function
vfs_write_suspend stops all new write operations to a filesystem,
allows any filesystem modifying system calls already in progress
to complete, then sync's the filesystem to disk and returns. The
function vfs_write_resume allows the suspended write operations to
begin again. Gating is not added by default for all filesystems as
for SMP systems it adds two extra locks to such critical kernel
paths as the write system call. Thus, gating should only be added
as needed.
Details on the use and current status of snapshots in FFS can be
found in /sys/ufs/ffs/README.snapshot so for brevity and timelyness
is not included here. Unless and until you create a snapshot file,
these changes should have no effect on your system (famous last words).
with splhigh(). However, the entropy-harvesting routine needs pretty
serious irq-protection, as it is called out of irq handlers etc.
Clues given by: bde
structure; remind myself in the cooments. Also regroup all the Yarrow
variables at the top of the variable list; they are "special".
(no functional change).
(I had been busy for my own research activity until the last weekend)
Supported devices:
SB Midi Port (sbc + midi)
SB OPL3 (sbc + midi)
16550 UART (midi, needs a trick in your hint)
CS461x Midi Port (csa + midi)
OSS-compatible sequencer (seq)
Supported playing software:
playmidi (We definitely need more)
Notes:
/dev/midistat now reports installed midi drivers. /dev/sndstat reports
only pcm drivers. We need the new name(pcmstat?).
EMU8000(SB AWE) does not sound yet but does get probed so that the OPL3
synth on an AWE card works.
TODO:
MSS/PCI bridge drivers
Midi-tty interface to support general serial devices
Modules
stack. It's bad for your machine's health.
Make the two huge structs in reseed() static to prevent crashes. This
is the bug that people have been running into and panic()ing on for the
past few days.
Reviewed by: phk
are working. Add a small blurb about XE_DEBUG as it might be useful
to some people troubelshooting problems in the future.
Submitted by: "Kevin Oberman" <oberman@es.net>
sure that it really is by issuing a ISPCTL_ABORT_CMD just on the
off chance the f/w will start it up again and, ha ha, start using
the DMA resources we gave it but are now taking away.
after the acquisition of any advisory locks. This fix corrects a case
in which a process tries to open a file with a non-blocking exclusive
lock. Even if it fails to get the lock it would still truncate the
file even though its open failed. With this change, the truncation
is done only after the lock is successfully acquired.
Obtained from: BSD/OS
us to not the ints are ok and also to (re)ENABLE isp interrupts. Remove
all splcam()/splx() invocates and replace them with ISP_LOCK/ISP_UNLOCK
macros.
to isp_osinfo substructure (all in prep for SMP). Define MBOX_WAIT_COMPLETE
and MBOX_NOTIFY_COMPLETE macros so that we can now (temp) use tsleep
to wait for mailbox completion. Requires us to guess whether we're
servicing an interrupt or not- will use intr_nesting_level.
Add local strncat function.
- Add 2 explicit (paranoid?) memory barriers in the
interrupt code (After the reading of the `flag' and
prior to looking at the data, of course. :-) ).
- Remove obsolete informations from the README.sym file.
This commit actually results in no object difference
for IA32, but 2x`mb' added for Alpha.
define). Fix stupidity wrt checking whether we've gone to
LOOP_PDB_RCVD loopstate- it's okay to be greater than this state.
D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC
macros.
Completely redo mailbox command routine (in preparation to make this
possibly wait rather than poll for completion).
Make a major attempt to solve the 'lost interrupt' problem
1. Problem
The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate
regular SCSI command placed on the request queue would never complete
and the watchdog routine in the driver would eventually wakeup and
catch it. This would typically only happen on Alphas, although a
couple folks with 700MHz Intel platforms have also seen this.
For a long time I thought it was a foulup with f/w negotiations of
SYNC and/or WIDE as it always seemed to happen right after the
platform it was running on had done a SET TARGET PARAMETERS mailbox
command to (re)enable sync && wide (after initially forcing
ASYNC/NARROW at startup). However, occasionally, the same thing
would also occur for the Fibre Channel cards as well (which, ahem,
have no SET TARGET PARAMETERS for transfer mode).
After finally putting in a better set of watchdog routines for the
platforms for this driver, it seemed to be the case that the command
in question (usually a READ CAPACITY) just had up and died- the
watchdog routine would catch it after ~10 seconds. For some platforms
(NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which
would always fail- indicating that the f/w denied knowledge of this
command, i.e., the f/w thought it was a done command). In any case,
retrying the command worked. But this whole problem needed to be
really fixed.
2. A False Step That Went in The Right Direction
The mailbox code was completely rewritten to no longer try and grab
the mailbox semaphore register and to try and 'by hand' complete
async fast posting completions. It was also rewritten to now have
separate in && out bitpatterns for registers to load to start and
retrieve to complete. This means that isp_intr now handles mailbox
completions.
This substantially simplifies the mailbox handling code, and carries
things 90% toward getting this to be a non-polled routine for this
driver.
This did not solve the problem, though.
3. Register Debouncing
I saw some comments in some errata sheets and some notes in a Qlogic
produced Linux driver (for the Qlogic 2100) that seemed to indicate
that debouncing of reads of the mailbox registers might be needed,
so I added this. This did not affect the problem. In fact, it made
the problem worse for non-2100 cards.
5. Interrupt masking/unmasking
The driver *used* to do a substantial amount of masking/unmasking
of the interrupt control register. This was done to make sure that
the core common code could just assume it would never get pre-empted.
This apparently substantially contributed to the lost interrupt
problem. The rewrite of the ICR (Interrupt Control Register),
which is a separate register from the ISR (Interrupt Status Register)
should not have caused any change to interrupt assertions pending.
The manual does not state that it will, and the register layout
seems to imply that the ICR is just an active route gate. We only
enable PCI Interrupts and RISC Interrupts- this should mean that
when the f/w asserts a RISC interrupt and (and the ICR allows RISC
Interrupts) and we have PCI Interrupts enabled, we should get a
PCI interrupt. Apparently this is a latch- not a signal route.
Removing this got rid of *most* but not all, lost interrupts.
5. Watchdog Smartening
I made sure that the watchdog routine would catch cases where the
Qlogic's ISR showed an interrupt assertion. The watchdog routine
now calls the interrupt service routine if it sees this. Some
additional internal state flags were added so that the watchdog
routine could then know whether the command it was in the middle
of burying (because we had time it out) was in fact completed by
the interrupt service routine.
6. Occasional Constipation Of Commands..
In running some very strenous high IOPs tests (generating about
11000 interrupts/second across one Qlogic 1040, one Qlogic 1080
and one Qlogic 2200 on an Alpha PC164), I found that I would get
occasional but regular 'watchdog timeouts' on both the 1080 and
the 2100 cards. This is under FreeBSD, and the watchdog timeout
routine just marks the command in error and retries it.
Invariably, right after this 'watchdog timeout' error, I'd get a
command completion for the command that I had thought timed out.
That is, I'd get a command completion, but the handle returned by
the firmware mapped to no current command. The frequency of this
problem is low under such a load- it would usually take an 30
minutes per 'lost' interrupt.
I doubled the timeout for commands to see if it just was an edge
case of waiting too short a period. This has no effect.
I gathered and printed out microtimes for the watchdog completed
command and the completion that couldn't find a command- it was
always the case that the order of occurrence was "timeout, completion"
separated by a time on the order of 100 to 150 ms.
This caused me to consider 'firmware constipation' as to be a
possible culprit. That is, resubmission of a command to the device
that had suffered a watchdog timeout seemed to cause the presumed
dead command to show back up.
I added code in the watchdog routine that, when first entered for
the command, marks the command with a flag, reissues a local timeout
call for one second later, but also then issues a MARKER Request
Queue entry to the Qlogic f/w. A MARKER entry is used typically
after a Bus Reset to cause the f/w to get synchronized with respect
to either a Bus, a Nexus or a Target.
Since I've added this code, I always now see the occasional watchdog
timeout, but the command that was about to be terminated always
now seems to be completed after the MARKER entry is issued (and
before the timeout extension fires, which would come back and
*really* terminate the command).
comment. Check against firmware state- not loop state when enabling
target mode. Other changes have to do with no longer enabling/disabling
interrupts at will.
Rearchitect command watchdog timeouts-
First of all, set the timeout period for a command that has a
timeout (in isp_action) to the period of time requested *plus* two
seconds. We don't want the Qlogic firmware and the host system to
race each other to report a dead command (the watchdog is there to
catch dead and/or broken firmware).
Next, make sure that the command being watched isn't done yet. If
it's not done yet, check for INT_PENDING and call isp_intr- if that
said it serviced an interrupt, check to see whether the command is
now done (this is what the "IN WATCHDOG" private flag is for- if
isp_intr completes the command, it won't call xpt_done on it because
isp_watchdog is still looking at the command).
If no interrupt was pending, or the command wasn't completed, check
to see if we've set the private 'grace period' flag. If so, the
command really *is* dead, so report it as dead and complete it with
a CAM_CMD_TIMEOUT value.
If the grace period flag wasn't set, set it and issue a SYNCHRONIZE_ALL
Marker Request Queue entry and re-set the timeout for one second
from now (see Revision 1.45 isp.c notes for more on this) to give
the firmware a final chance to complete this command.
store a bitmask of whether we've set a value into ccb->ccb_h.status,
whether we're in the watchdog routine for this command now, whether
we've set a grace period for this command and whether this command is
actually done.
See comments of rev 1.45 of isp.c for more complete information.
output mailbox values we want to get back out of the chip once a mailbox
command is done. Add storage for the maximum number of output mailbox
registers to the softc.
Roll minor version number.
the handle (i.e., generation number), so we will now need a function that
will take a handle and return a flat index [ 0 .. maxhandles-1 ] for
auxillary routines that need an index to get at buddy store values
(like dma maps or xflist pointers).
device with Yarrow, and although I coded for that in dev/MAKEDEV, I forgot
to _tell_ folks.
This commit adds back the /dev/urandom device (as a duplicate) of /dev/random,
until such time as it can be properly announced.
This will help the openssl users quite a lot.
(Reported by Matthew Jacob)
- Fix a couple of __inline__ (changed to __inline).
- Check also against DT_DATA_IN phase on parity/crc error.
(Merged from Pamela Delaney's changes in the Linux driver)
- Fix support for phase mismatch handling from the C code for
the C1010 (only useful for testing issue).
- Add an asynchonous notification handler for `lost device'
(AC_LOST).
This merges in changes from NetBSD which ensure bktr0
(actually bktr%d) is printed at the start of any output lines.
Submitted by: Thomas Klausner <wiz@danbala.ifoer.tuwien.ac.at>
This is work-in-progress, and the entropy-gathering routines are not
yet present. As such, this should be viewed as a pretty reasonable
PRNG with _ABSOLUTELY_NO_ security!!
Entropy gathering will be the subject of ongoing work.
This is written as a module, and as such is unloadable, but there is
no refcounting done. I would like to use something like device_busy(9)
to achieve this (eventually).
Lots of useful ideas from: bde, phk, Jeroen van Gelderen
Reviewed by: dfr
severely stripped down compared with its predecessor, and is measurably
a _lot_ faster.
Many thanks to Jeroen van Gelderen for lots of good ideas.
There is still a problem with this; it is written as a mudule, and as
such is theoretically unloadable. However, there is no refcounting done
as I would prefer to do that a'la device_busy(9), rather than some
"home-rolled" scheme. The point is pretty moot, as /dev/null is
effectively compulsory.
Reviewed by: dfr
the PnP probe is merely a stub as we make assumptions about some of this
hardware before we have probed it.
Since these devices (with the exception of the speaker) are 'standard',
suppress output in the !bootverbose case to clean up the probe messages
somewhat.
Renamed varible dst in ray_rx to mp as it is a pointer to an mbuf.
Correctly grok addresses in data packets.
Promte a couple of RECERRs to real errors.
Rewrote intro at top of file to reflect my better understanding of how it
the memory mapping works.
Clear the DONE list and move some thoughts into the TODO list.
Remove RECERR from RAY_DEBUG
Start to use a desired network parameter structure, only used in download
code as I've realised that there are some problems with the idea.
Break up ray_rx, and move the data packet handler into a seperate function. This meant some knock on changes in ray_rx_mgt/ray_rx_ctl to do with
mbuf freeing.
Remove some debug code/XXX comments that are out of date.
Force alphas to prefer mem mapping as the default.
Basically, we have a pointer to a function which we can call which will
return us a pointer to firmware for the card we have. We call this function
(if it's non-NULL) with the address of our mdvec f/w pointer.
The way this works is that if ispfw (as a module or a static) is loaded,
it initializes the pointer in isp_pci, so we can call into to it to fetch
a pointer to a f/w set.
If ispfw is MOD_UNLOADed, it's retained a pointer to our mdvec f/w pointers,
which then get zeroed out so we don't have any references to data that's
now gone from kernel memory. Removing the f/w saves ~360KBytes.
Alas, there is no autounload mechanism that works for is here.
through, establish what our LUN width is. Unfortunately, we can't ask
the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs
(SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't
load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We
have to assume only one LUN for Fibre Channel because the LUN setting
in Request Queue entries is in different places whether we have SCCLUN
firmware or not, so the only LUN guaranteed to work for both is LUN 0.
Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used-
instead use run time determinants based upon isp->isp_maxluns.
After starting firmware, delay 500us to give it a chance to get rolling.
Fix the interrupt service routine to check for both isr && sema being zero
before thinking this was a spurious interrupt. Following the manuals,
allow for both Mailbox as well as Queue Reponse type interrupts for regular
SCSI.
(we always support fabric now). Remove SCCLUN definition (we always
support SCCLUN now, if we load the f/w). Add typedef definition of an
external firmware fetch function.
need this RSN.
Remove a pointless warning in the root device locating code.
Remove the "wd" compatibility name from the "ad" driver.
WARNING: If you have not updated to use /dev/wd* in your /etc/fstab
and modern bootblocks, it would be a very good idea to do so BEFORE
you upgrade your kernel.
Implement the Solaris way to break into DDB over a serial console
instead of sending a break. Sending the character sequence
CR ~ ^b will break the kernel into DDB (if DDB is enabled).
Reviewed by: peter
layout introduced in driver 1.5.3. The driver was
confused by the bogus TEKRAM table used to translate
user sync. setting to SCSI sync. factor.
Btw, the new TEKRAM DC-390 U3D and U3W Ultra-160
controllers seem to be using BIOS from SYMBIOS/LSI
and thus SYMBIOS NVRAM layout.
If that means that TEKRAM will now offer real
SYMBIOS software compatible SCSI controllers, then
it is a *GREAT NEWS*.
What we'd like to know is whether or not we have a listener
upstream that really hasn't configured yet. If we do, then
we can give a more sensible reply here. If not, then we can
reject this out of hand.
Choices for what to send were
Not Ready, Unit Not Self-Configured Yet
(0x2,0x3e,0x00)
for the former and
Illegal Request, Logical Unit Not Supported
(0x5,0x25,0x00)
for the latter.
We used to decide whether there was at least one listener
based upon whether the black hole driver was configured.
However, recent config(8) changes have made this hard to do
at this time.
Actually, we didn't use the above quite yet, but were sure considering it.
Generated a new macor, RAY_RECERR for reporting errors with. Verbosity set with IFF_DEBUG (recommended at present).
Add PRIBIO to tsleeps.
Catch detach on ray_ccs_alloc a little better.
Move sc_promisc into desired and current n/w parameters.
Remove IFQ_PEEK, we know the driver runs okay without it.
Drain the output queue in ray_stop.
Only use ray_mcast for ADD/DEL multi ioctls. ray_init_multi resets the
multicast list on startup. Simplifies ray_init a little.
Tidy some old comments.
ray_download_done now copies the whole desired n/w parameter set into the
current set. This is because I was missing soem parameters - like the
net type!
2. Newbusify the driver.
3. Build as a module.
4. Use correct minor numbers when creating device files.
5. Correctly lock control characters.
6. Return ENXIO when device not configured.
Submitted by: Tor Egge <Tor.Egge@fast.no>
7. Fix the baud_table.
Submitted by: Elliot Dierksen <ebd@oau.org>
Note:
- the old driver still lives in src/sys/i386/isa, so that you can
revert to it if something goes wrong.
- The module does not detach very well. Attaching works fine.
map physical addresses below 0x2000 (accoding to AMI). If we
allocate our s/g tables and get an address below this point, leak the
memory and try again.
This should fix booting from these controllers.
Get ray_detach working correctly. This is a very simple routine as it
just wakes up sleeping processes. Note that anything woken has NO softc
structure available! runq_add is suitably modified to detect a detach and
return straight away.
Due to ray_detach and its implications use a macro for adding things
to the runq in user land.
tested on Intel BX chipsets only. The other agp minidrivers are totally
untested.
The programming api is a subset of the Linux api and is only intended to
be enough for the X server to use. There is also an in-kernel api for the
use of other kernel modules such as the 3D DRI.
21143 chips, I accidentally removed the DC_MII_REDUCED_POLL flag
for all 21143 cards. This caused problems with timer-instigated
TCP retransmits, which happened to occur at the same time as an
MII poll tick on MII-based cards (e.g. D-Link DFE-570TX). Fixed this,
plus made some other cleanups. The autoneg fixes for the non-MII
cards still work. Also tested the PNIC II now that I have one again.
Fix several instances of breakage in RAID-5 revive code.
Tidy up code.
parityops:
Don't attempt to do anything if the plex is degraded or worse.
parityrebuild:
Add comments.
Perform transfers in correct length.
after autoneg so we make sure to set the link state and duplex mode
correctly.
- Make sure to set the 'ignore pause frames' bit on the XMAC.
- Small linewrap fix.
needed to add into ether_input) and finally sorting IFF_RUNNING through
whole driver.
As part of the IFF_RUNNING stuff, we've added an extra flag so callers
can request that runq routines should check IFF_RUNNING before executing.
Remove BPF taps as this is now done by ether_input.
Resurrect multicast code, moving the multicast list stuff to the runq
routine.
Dump ray_promisc_user as all flag changes are now handled by ray_init, and
add a couple of checks to ray_promisc.
In uppparams_user, allow changes before the card is running (need to
fix some breakage with _download here later). In addition, don't
assume that the current n/w parameters are valid - they are only valid
in the runq.
Fix a nasty flag bug - runq_add cleared all the flags on the last command!
Remove the hacks for setting the memory flags - problems were down
to buggy versions of pccardd. For some reason pccardd only dtrt with
the "right" debug_level.
not gone yet.
format_config: print correct text when a volume has a preferred plex.
This is still broken, but not quite as badly.
Reported-by: Phil Regnauld <regnauld@ftf.net>
Change a rather silly comment.
routines from foo_watchdog() because foo_watchdog() is called at
interrupt context, and that's a no-no due to the way the USB stack
is currently set up.
What we do now is call the TX end of frame handler manually to clear
the completed transmission, then check the send queue and send off
any frames that are pending.
Also turned off the interrupt pipe stuff in if_aue, since it appears
to tickle a bug in the USB stack that I haven't found yet.
motherboards that use YMF740's. It has a strange subvendor and subdevice
ID and requires a disturbingly long delay after the ac97 codec init.
Cameron hasn't had this driver tested on another 740 yet, so we don't know
if this is a quirk of all 740's, or if its just something about the codec
that Intel used.
workalike chips (Macronix 98713A/98715 and PNIC II). Timing is somewhat
critical: you need to bring the link as soon as possible after NWAY
is done, and the old one second polling interval was too long. Now
we poll every 10th of a second until NWAY completes (at which point
we return to the 1 second interval again to keep an eye on the link
state).
I tested all the other cards I had on hand to make sure I didn't bust
any of them and they seem to work (including the MII-based 21143 card).
This should fix some autoneg problems with DE500-BA cards and the
built-in 10/100 ethernet on some alpha systems.
(Now before anyone asks why I never noticed this before, the old code
worked just find with the Intel swich I used for testing back in NY.
Apparently not all switches are as picky about the timing.)
It may cause misterious chars appearse in the middle of the scrolled lines.
The bug trigger: enter
grep P_32 /usr/include/*.h
command and see misterious "db.\" filename.
Simple stuff
------------
Split _download up so that the MIB settings are in their own functions.
Made "tx completed but status is ..." a recoverable error
Cut down verbosity of "unloaded" messages
Moved ccs_free and com_runq from intr_ccs to ecf_done and runq_done
to avoid embarasing mistakes and waits.
Merged runq_add and runq_arr into one and called it runq_add
Made RAY_COM_DUMP a real debug called RAY_DCOM
Consistnet debugging around tsleeps.
Use bus_activate_resource for attr/cm mapping, and set the flags
correctly in the allocation routines (needs more hacks to
sys/pccard/pcic.c)
com_malloc is now seperated from the comq initialization. This was
done whilst trying to set automatic variables for the comqs.
Harder Stuff
------------
As part of the IFF_RUNNING fixes, remove the panic in runq if we are
not running.
Change, again, runq_add. This time we don't do any cleaning up
if there were errors. This is so that callers get the chance
to re-try (not that I ever see it being used).
In runq_add, only sleep when there is something to sleep on!
ioctl locking routines, stolen from awi.c but not used
Hardest Stuff
-------------
Dealing with serialing ioctls correctly means that we must QUEUE
changes to IFF_RUNNING and check it in the QUEUED commands, not
in the user commands. Whilst simple to state, it took a few
hours of head scratching to get it right. The realisation was that
I only have to guarantee that sub-commands from a single process
are serialised and "atomic", and that they check the status of the
interface flags when invoked and not when they are queued.
Another way of looking at it, is that the driver's state is stored
in the runq and the IFF_RUNNING flag. These must be changed together.
What this means practically, is that IFF_RUNNING is set after
we have started/joined/associated with a network. And it is
cleared by ray_stop via the runq so that unfinsished commands are
not distrupted.
I still have to fix up promisc, upp/repparams and mcast.
Oh yeah, stop is essentially a noop in that it only
changes IFF_RUNNING
- Get rid of a fiew uselessly `long' variables
and casts to `long'.
- Estimate the PCI clock for all chips, except
C1010 for now (we should do that for each PCI BUS)
- Refine a couple of C1010 errata work-arounds.
- For now, make sure AIP generation is disabled
for the C1010-66.
"options COMPAT_OLDPCI". This option already existed, but now also tidies
up the declarations in #include <pci/pci*.h>. It is amazing how much stuff
was using the old pre-FreeBSD 3.x names and going silently undetected.
all other modes not set ALKED flag and it means that CapsLock always turned
off for them.
Real bug example is X11 which never turn on CapsLock with Russian keyboard.
PR: 18651
Submitted by: "Mike E. Matsnev" <mike@po.cs.msu.su>
more frequently than the core part of the sio driver, it might
be good to move the PnP IDs to sio_isapnp.h or something like
that.
PR: i386/18828
Submitted by: J.P. King <jpk28@cam.ac.uk>
Make the error recovery code a little more obvious.
Inform the user if UDMA66 mode couldn't be selected due to a
non ATA66 compliant 80pin cable.
Minor cosmetics.
to various pmap_*() functions instead of looking up the physical address
and passing that. In many cases, the first thing the pmap code was doing
was going to a lot of trouble to get back the original vm_page_t, or
it's shadow pv_table entry.
Inspired by: John Dyson's 1998 patches.
Also:
Eliminate pv_table as a seperate thing and build it into a machine
dependent part of vm_page_t. This eliminates having a seperate set of
structions that shadow each other in a 1:1 fashion that we often went to
a lot of trouble to translate from one to the other. (see above)
This happens to save 4 bytes of physical memory for each page in the
system. (8 bytes on the Alpha).
Eliminate the use of the phys_avail[] array to determine if a page is
managed (ie: it has pv_entries etc). Store this information in a flag.
Things like device_pager set it because they create vm_page_t's on the
fly that do not have pv_entries. This makes it easier to "unmanage" a
page of physical memory (this will be taken advantage of in subsequent
commits).
Add a function to add a new page to the freelist. This could be used
for reclaiming the previously wasted pages left over from preloaded
loader(8) files.
Reviewed by: dillon
It's not clear what this does nor why they would do it, but it should
compile, now. This could be a case where fixing the code so that it
compiles merely masks more devious dysfunctional behaviour.
Note that __bsdi__s_/_i_/_os_/__ has moved this file to dev/ic/ and
has completely removed the non-compiling function from pdq_ifsubr.c and
has completely removed this function and placed it into netinet/if_ether.c
(if, in fact, it wasn't there the whole time). I was tempted to simply
remove this __bsdi__only__ function.
The function is arp_ifinit().
PR: kern/7903
proc pointer is believed to have been the cause of panics related to vnconfig
on top of intr-optioned NFS mounts.
Reported by: "Sean O'Connell" <sean@stat.Duke.EDU>
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
of using the MGETHDR macro all the time. When an mbuf is reused as a
header, initialize csum_flags to zero as well, so the delayed_checksum
call woks properly.
Debbugging work done by: jmas
revive_block: Correct bug introduced in revision 1.25 which caused
Add fields to vinum_ioctl_msgexcessive concurrent requests followed by
system death.
Move to using /sys/dev/ray for driver
Backport -current ray_res code - most are stubs.
Make ray_attr stuff look like currents layout.
Make attribute memory access use a macro and ripple through.
Drop FIXUP as we always need it
changes: consider a new PDB entry different if Class 3 service parameter
roles change (!!!). Do some checking as we're getting a port database
that traps whether things change while we're doing so. Handle N-port
and F-ports correctly. Fix the fabric login loop to retain a login/binding
if things haven't changed (I mean, why logout a device only to log it back
in). No longer accept, after fabric logins, garbage if we can't get a PDB
entry that matches the device we've just logged into- if it doesn't, log
it out as it is very unlikely to still be what we thought it was. Get rid
of some of the debounce loops because we could get stuck there.
Apparently the f/w has finished the command, but somehow an interrupt is
being lost. So, we just plain wedge when booting alphas.
This is a general routine we've needed for a while.
ums driver (mouse) and get the usb driver at the same time.
This also shows that
MODULE_VERSION(usb, 1);
MODULE_DEPEND(usb, usb, 1, 1, 1);
in the same module in one source file works.
functions.
If it is defined, check whether bus_alloc_resource has succeeded. If it
hasn't, it is in polled mode. Mike Nowlin reports that this change makes
the geek port (whatever _that_ is :-) work again on his machine.
Submitted by: Mike Nowlin <mike@argos.org>
so that we return failure when we've failed and succeed when we succeed.
Otherwise, users always get a sn device :-(.
PR: 18431
Submitted by: <sanpei@sanpei.org> MIHIRA Yoshiro-san
Move the code that checks the card into _probe and out of _attach and
shuffle a couple of things around in attach.
Set ifp in the variable block - catches unused variables.
of some function names, dropping the ISA bits that were never used and
removing __P
We've renamed the _pccard_ stuff as nothing else probes or attaches.
In the next commit we will move some routines around and split out some of the
structure definitions to another file.
I've dropped the SYSCTL as I never got it working. APM is gone too as it
is broken.
Note, that the attr_read/write will be in both this and NEWCARD/NEWBUS so
I've moved the prototypes to the right place.
Add a few casts.
- Reload SCNTL3 after selection from host (C1010-33).
- Reload SCNTL4 prior to any DATA OUT phase (C1010-66).
- Use max SCSI offset 31 for ST but 62 for DT.
for transmit to the adapter, not when we receive a transmit interrupt
indicating that they were sent. This fix now allows tcpdump to produce
sane results by recording the timestamp at the point where the mbuf was
actually transmitted.
can use all of the s/g entries available on smaller cards. This is
necessary if we want to be able to handle a non-page-aligned 64k transfer
on 2.x and 3.x firmware.
Fix a missing splx() that may have left us at splbio() for longer than
desired.
Reduce shadowing of controller-supplied parameters a little.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
which seems to correspond better with what a busy plex needs. This
may also help us avoid race conditions when expanding the table which
may have been contributing to the random corruption, panics and hangs
we've been seeing in RAID-5 plexes, particularly with ata drives.
Eagerly-awaited-by: sos
Get counting volume I/Os right.
launch_requests: Be macho, throw away the safety net and walk the
tightrope with no splbio().
Add some comments explaining the smoke and mirrors.
Remove some redundant braces.
sdio: Set the state of an accessed but down subdisk correctly. This
appears to duplicate an earlier commit that I hadn't seen.
Get counting volume I/Os right.
Count buffer sizes correctly for architectures where ints are not 32 bits.
complete_rqe: Move decrementing active count until after call to
complete_raid5_write, thus possibly avoiding a race condition.
Suggested-by: dillon
Rename user bp to ubp to avoid confusion.
Tidy up comments.
a struct buf. Don't try to examine B_ASYNC, it is a layering violation
to do so. The only current user of this interface is vn(4) which, since
it emulates a disk interface, operates on struct bio already.
ioccom.h defines only implementation detail, and should therefore
only be included from the #include which defines the ioctl tags,
in other words: never include it from *.c
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
coming later this week. Mitsuru IWASAKI provided a patch to -mobile which
I used to make sure I was doing the right thing but only a small part of
the actual patch was used.
that fails to proberly close the disk.
The problem seems to be that the HP burners sometimes return
ready when they actually are not, the solution is to not use
immediate mode on the closing commands. This is suboptimal
for real burners, in that they now hog the ATA bus for possibly
minutes, where its really not nessesary, *sigh*.
not u_long. On i386's with 64-bit longs, returning u_longs indirectly
in (more than) the space reserved for uintptr_t's tended to corrupt the
previous frame pointer in the stack frame, so it was not easy to debug.
The type mismatches are hidden by the bogus cast in DEVMETHOD().
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
53C810 non 'A', 53C815 and 53C825 non 'A' are now
attached by the driver (by default).
The driver uses a different SCRIPTS set based on
MEMORY MOVE instructions for these chips.
2 SCRIPTS sets (firmwares) numbered #1 and #2 are
used for the whole support of the 53C8XX family
to get possible:
- FW #1 : Only based on MEMORY MOVE instructions.
Selected for 810, 815, 825.
- FW #2 : LOAD/STORE based. This is the firmware
also used by previous driver versions.
Selected for other chips.
When both `ncr' and `sym' are configured, `sym'
will now attach all the 53C8XX devices by default.
Previous balancing between `ncr' and `sym' can be
preserved by:
- Either editing sym_conf.h and commenting the
following compile option:
#define SYM_CONF_GENERIC_SUPPORT
(This also saves about 3.5Kb of kernel memory).
- Or setting kernel config option
SYM_SETUP_LP_PROBE_MAP to 64 (bit 0x40)
