o Make the comments KNF-compliant.
o Use nanotime instead of getnanotime; the manpage lies about the
kern.timecounter.method - it has been removed.
o Fix the ENTROPYSOURCE const permanently.
o Make variable names more consistent.
o Make function prototypes more consistent.
Some more needs to be done; to follow.
cards. This basically involves switching to the 12.4.13 firmware, plus
a couple of minor tweaks to the driver.
Also changed the jumbo buffer allocation scheme just a little to avoid
'failed to allocate jumbo buffer' conditions in certain cases.
support for relocating the port address if the isa hints specify a
different address from the address the chipset currently has.
Submitted by: Andrew M. Miklic <miklic@ibm.net>
lock up under moderate to heavy load.
The status & command fields share a 32-bit longword. The programming
API of the eepro apparently requires that you update the command field
of a transmit slot that you've already given to the card. This means
the card could be updating the status field of the same longword at
the same time. Since alphas can only operate on 32-bit chunks of
memory, both the status & command fields are loaded from memory &
operated on in registers when the following line of C is executed:
sc->cbl_last->cb_command &= ~FXP_CB_COMMAND_S;
The race is caused by the card DMA'ing up the status at just the wrong
time -- after it has been loaded into a register & before it has been
written back. The old value of the status is written back, clobbering
the status the card just DMA'ed up. The fact that the card has sent
this frame is missed & the transmit engine appears to hang.
Luckily, as numerous people on the freebsd-alpha list pointed out, the
load-locked/store-conditional instructions used by the atomic
functions work with respect changes in memory due to I/O devices. We
now use them to safely update the command field.
Tested by: Bernd Walter <ticso@mail.cicely.de>
errors that plagued those cards with XFree86 4.0. They have two memory
ranges as well as an IO port range to them. Also cleaned up the three
warning messages that I got, from inb(), outb() and linuxulator. Also, I
noticed that the DRI and Glide support for the Voodoo4 and 5 has been
placed upon linux.3dfx.com, too bad they haven't released the tech docs
yet. Apparently, they are still pushing glide for all of us, so I will try
and add support once those tech docs are up.
other systems.
o Normalize copyright text.
o Clean up probe code function interfaces by passing around a single
structure of common arguments instead of passing "too many" args
in each function call.
o Add support for the AAA-131 as a SCSI adapter.
o Add support for the AHA-4944 courtesy of "Matthew N. Dodd" <winter@jurai.net
o Correct manual termination support for PCI cards. The bit definitions
for manual termination control in the SEEPROM were incorrect.
o Add support for extracting NVRAM information from SCB 2 for BIOSen
that use this mechanism to pass this data to OS drivers.
o Properly set the STPWLEVEL bit in PCI config space based on the
setting in an SEEPROM.
o Go back to useing 32byte SCBs for all controllers. The current
firmware allows us to embed 12byte cdbs on all controllers in
a 32byte SCB, and larger cdbs are rarely used, so it is a
better use of this space to offer more SCBs (32).
o Add support for U160 transfers.
o Add an idle loop executed during data transfers that prefetches
S/G segments on controllers that have a secondary DMA engine
(aic789X).
o Improve the performance of reselections by avoiding an extra
one byte DMA in the case of an SCB lookup miss for the reselecting
target. We now keep a 16byte "untagged target" array on the card
for dealing with untagged reselections. If the controller has
external SCB ram and can support 64byte SCBs, then we use an
"untagged target/lun" array to maximize concurrency. Without
external SCB ram, the controller is limited to one untagged
transaction per target, auto-request sense operations excluded.
o Correct the setup of the STPWEN bit in SXFRCTL1. This control
line is tri-stated until set to one, so set it to one and then
set it to the desired value.
o Add tagged queuing support to our target role implementation.
o Handle the common cases of the ignore wide residue message
in firmware.
o Add preliminary support for 39bit addressing.
o Add support for assembling on big-endian machines. Big-endian
support is not complete in the driver.
o Correctly remove SCBs in the waiting for selection queue when
freezing a device queue.
o Now that we understand more about the autoflush bug on the
aic7890, only use the workaround on devices that need it.
o Add a workaround for the "aic7890 hangs the system when you
attempt to pause it" problem. We can now pause the aic7890
safely regardless of what instruction it is executing.
allocate a short port range in some alpha configurations.
Submitted by: "Andrew M. Miklic" <miklic@udlkern.fc.hp.com>,
Mark Abene <phiber@radicalmedia.com>
when we're done reading it (makes checking things easier).
Before calling isp_notify_ack make sure we're at RUNSTATE-
elsewise we can be responding to LIPs or SCSI bus resets
before we've finished some of the wiring.
we need a function that tells the Qlogic f/w that a target mode command
is done, so increase the resource count for that lun. Add in a timeout
function to kick the putback again if we fail to do it the first time (we
may not have the request queue space for ATIO push). Split the function
isp_handle_platform_ctio into two parts so that the timeout function for
the ATIO push or isp_handle_platform_ctio can inform CAM that the requested
CTIO(s) are now done.
Clean up (cough) residual handling. What we need for Fibre Channel
is to preserve the at_datalen field from the original incoming ATIO
so we can calculate a 'true' residual. Unfortunately, we're not
guaranteed to get that back from CAM. We'll *try* to find it hiding
in the periph_priv field (layering violation)- but if an ATIO was
passed in from user land- forget it. This means that we'll probably
get residuals wrong for Fibre Channel commands we're completing
with an error. It's too late to 4.1 release to fix this- too bad.
Luckily the only device we'd really care about this occurring on
is a tape device and they're still so rare as FC attached devices
that this can be considered an untested combination anyway.
Remove all CCINCR usage (resource autoreplenish). When we've proved
to ourself that things are working properly, we can add it back
in.
Make sure we propage 'suggested' sense data from the incoming ATIO
into the created system ATIO- and set sense_len appropriately.
Correctly propagate tag values.
Fall back to the model of generating (well, the functions in isp_pci.c
do the work) multiple CTIOs based upon what we get from XPT. Instead
of being able to pair Qlogic generated ATIOs with CAM ATIOs, and then
to pair CAM CTIOs with Qlogic CTIOs, we have to take the CTIO passed
to us from XPT, and if it implies that we have to generate extra
Qlogic CTIOs, so be it. This means that we have to wait until the
last CTIO in a sequence we generated completes before calling xpt_done.
Executive summary- target mode actually now pretty much works well
enough to tell folks about.
There is a number of devices that are compliant, of which the 3Com 5605 is
has been verified to work.
The driver is not perfect yet, but should be able to get you somewhere.
The driver was originally written by Lennart Augustsson, but Mike Smith
and Mike Meyer <mwm@mired.org> did the porting.
3.3volt PCI/cardbus chipsets similar to the 98715 (and they have
512-bit hash tables). Also update the man page to mention the 98727/98732
and the SOHOware SFA110A Rev B4 card with the 98715AEC-C chip.
entropy estimation, but causes an immediate reseed after the input
(read in sizeof(u_int64_t) chunks) is "harvested".
This will be used in the reboot "reseeder", coming in another
commit. This can be used very effectively at any time you think
your randomness is compromised; something like
# (ps -gauxwww; netstat -an; dmesg; vmstat -c10 1) > /dev/random
will give the attacker something to think about.
non-disconnecting command. Interestingly enough, of the other flavors
of the 7.65 f/w (the dual-id and multi-id flavor)- the dual-id doesn't
hang (they're also supposed to be the same except for supporting dual
or multi-id capture!), but other things are questionable as well.
which differ slightly from the Macronix MX98715AEC chip on the sample
adapter that I have in that the multicast hash table is only 128 bits
wide instead of 512. New adapters are popping up with this chip, and
due to improper handling of the smaller hash table, broadcast packets
were not being received correctly.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
associated patch to XFree86 allows the X server to work with this chipset
on FreeBSD. Additional work will include porting the Linux 3D driver.
Submitted by: Ruslan Ermilov <ru@FreeBSD.org>
the gating of system calls that cause modifications to the underlying
filesystem. The gating can be enabled by any filesystem that needs
to consistently suspend operations by adding the vop_stdgetwritemount
to their set of vnops. Once gating is enabled, the function
vfs_write_suspend stops all new write operations to a filesystem,
allows any filesystem modifying system calls already in progress
to complete, then sync's the filesystem to disk and returns. The
function vfs_write_resume allows the suspended write operations to
begin again. Gating is not added by default for all filesystems as
for SMP systems it adds two extra locks to such critical kernel
paths as the write system call. Thus, gating should only be added
as needed.
Details on the use and current status of snapshots in FFS can be
found in /sys/ufs/ffs/README.snapshot so for brevity and timelyness
is not included here. Unless and until you create a snapshot file,
these changes should have no effect on your system (famous last words).
with splhigh(). However, the entropy-harvesting routine needs pretty
serious irq-protection, as it is called out of irq handlers etc.
Clues given by: bde
structure; remind myself in the cooments. Also regroup all the Yarrow
variables at the top of the variable list; they are "special".
(no functional change).
(I had been busy for my own research activity until the last weekend)
Supported devices:
SB Midi Port (sbc + midi)
SB OPL3 (sbc + midi)
16550 UART (midi, needs a trick in your hint)
CS461x Midi Port (csa + midi)
OSS-compatible sequencer (seq)
Supported playing software:
playmidi (We definitely need more)
Notes:
/dev/midistat now reports installed midi drivers. /dev/sndstat reports
only pcm drivers. We need the new name(pcmstat?).
EMU8000(SB AWE) does not sound yet but does get probed so that the OPL3
synth on an AWE card works.
TODO:
MSS/PCI bridge drivers
Midi-tty interface to support general serial devices
Modules
stack. It's bad for your machine's health.
Make the two huge structs in reseed() static to prevent crashes. This
is the bug that people have been running into and panic()ing on for the
past few days.
Reviewed by: phk
are working. Add a small blurb about XE_DEBUG as it might be useful
to some people troubelshooting problems in the future.
Submitted by: "Kevin Oberman" <oberman@es.net>
sure that it really is by issuing a ISPCTL_ABORT_CMD just on the
off chance the f/w will start it up again and, ha ha, start using
the DMA resources we gave it but are now taking away.
after the acquisition of any advisory locks. This fix corrects a case
in which a process tries to open a file with a non-blocking exclusive
lock. Even if it fails to get the lock it would still truncate the
file even though its open failed. With this change, the truncation
is done only after the lock is successfully acquired.
Obtained from: BSD/OS
us to not the ints are ok and also to (re)ENABLE isp interrupts. Remove
all splcam()/splx() invocates and replace them with ISP_LOCK/ISP_UNLOCK
macros.
to isp_osinfo substructure (all in prep for SMP). Define MBOX_WAIT_COMPLETE
and MBOX_NOTIFY_COMPLETE macros so that we can now (temp) use tsleep
to wait for mailbox completion. Requires us to guess whether we're
servicing an interrupt or not- will use intr_nesting_level.
Add local strncat function.
- Add 2 explicit (paranoid?) memory barriers in the
interrupt code (After the reading of the `flag' and
prior to looking at the data, of course. :-) ).
- Remove obsolete informations from the README.sym file.
This commit actually results in no object difference
for IA32, but 2x`mb' added for Alpha.
define). Fix stupidity wrt checking whether we've gone to
LOOP_PDB_RCVD loopstate- it's okay to be greater than this state.
D'oh! Protect calls to isp_pdb_sync and isp_fclink_state with IS_FC
macros.
Completely redo mailbox command routine (in preparation to make this
possibly wait rather than poll for completion).
Make a major attempt to solve the 'lost interrupt' problem
1. Problem
The Qlogic cards would appear to 'lose' interrupts, i.e., a legitimate
regular SCSI command placed on the request queue would never complete
and the watchdog routine in the driver would eventually wakeup and
catch it. This would typically only happen on Alphas, although a
couple folks with 700MHz Intel platforms have also seen this.
For a long time I thought it was a foulup with f/w negotiations of
SYNC and/or WIDE as it always seemed to happen right after the
platform it was running on had done a SET TARGET PARAMETERS mailbox
command to (re)enable sync && wide (after initially forcing
ASYNC/NARROW at startup). However, occasionally, the same thing
would also occur for the Fibre Channel cards as well (which, ahem,
have no SET TARGET PARAMETERS for transfer mode).
After finally putting in a better set of watchdog routines for the
platforms for this driver, it seemed to be the case that the command
in question (usually a READ CAPACITY) just had up and died- the
watchdog routine would catch it after ~10 seconds. For some platforms
(NetBSD/OpenBSD)- an ABORT COMMAND mailbox command was sent (which
would always fail- indicating that the f/w denied knowledge of this
command, i.e., the f/w thought it was a done command). In any case,
retrying the command worked. But this whole problem needed to be
really fixed.
2. A False Step That Went in The Right Direction
The mailbox code was completely rewritten to no longer try and grab
the mailbox semaphore register and to try and 'by hand' complete
async fast posting completions. It was also rewritten to now have
separate in && out bitpatterns for registers to load to start and
retrieve to complete. This means that isp_intr now handles mailbox
completions.
This substantially simplifies the mailbox handling code, and carries
things 90% toward getting this to be a non-polled routine for this
driver.
This did not solve the problem, though.
3. Register Debouncing
I saw some comments in some errata sheets and some notes in a Qlogic
produced Linux driver (for the Qlogic 2100) that seemed to indicate
that debouncing of reads of the mailbox registers might be needed,
so I added this. This did not affect the problem. In fact, it made
the problem worse for non-2100 cards.
5. Interrupt masking/unmasking
The driver *used* to do a substantial amount of masking/unmasking
of the interrupt control register. This was done to make sure that
the core common code could just assume it would never get pre-empted.
This apparently substantially contributed to the lost interrupt
problem. The rewrite of the ICR (Interrupt Control Register),
which is a separate register from the ISR (Interrupt Status Register)
should not have caused any change to interrupt assertions pending.
The manual does not state that it will, and the register layout
seems to imply that the ICR is just an active route gate. We only
enable PCI Interrupts and RISC Interrupts- this should mean that
when the f/w asserts a RISC interrupt and (and the ICR allows RISC
Interrupts) and we have PCI Interrupts enabled, we should get a
PCI interrupt. Apparently this is a latch- not a signal route.
Removing this got rid of *most* but not all, lost interrupts.
5. Watchdog Smartening
I made sure that the watchdog routine would catch cases where the
Qlogic's ISR showed an interrupt assertion. The watchdog routine
now calls the interrupt service routine if it sees this. Some
additional internal state flags were added so that the watchdog
routine could then know whether the command it was in the middle
of burying (because we had time it out) was in fact completed by
the interrupt service routine.
6. Occasional Constipation Of Commands..
In running some very strenous high IOPs tests (generating about
11000 interrupts/second across one Qlogic 1040, one Qlogic 1080
and one Qlogic 2200 on an Alpha PC164), I found that I would get
occasional but regular 'watchdog timeouts' on both the 1080 and
the 2100 cards. This is under FreeBSD, and the watchdog timeout
routine just marks the command in error and retries it.
Invariably, right after this 'watchdog timeout' error, I'd get a
command completion for the command that I had thought timed out.
That is, I'd get a command completion, but the handle returned by
the firmware mapped to no current command. The frequency of this
problem is low under such a load- it would usually take an 30
minutes per 'lost' interrupt.
I doubled the timeout for commands to see if it just was an edge
case of waiting too short a period. This has no effect.
I gathered and printed out microtimes for the watchdog completed
command and the completion that couldn't find a command- it was
always the case that the order of occurrence was "timeout, completion"
separated by a time on the order of 100 to 150 ms.
This caused me to consider 'firmware constipation' as to be a
possible culprit. That is, resubmission of a command to the device
that had suffered a watchdog timeout seemed to cause the presumed
dead command to show back up.
I added code in the watchdog routine that, when first entered for
the command, marks the command with a flag, reissues a local timeout
call for one second later, but also then issues a MARKER Request
Queue entry to the Qlogic f/w. A MARKER entry is used typically
after a Bus Reset to cause the f/w to get synchronized with respect
to either a Bus, a Nexus or a Target.
Since I've added this code, I always now see the occasional watchdog
timeout, but the command that was about to be terminated always
now seems to be completed after the MARKER entry is issued (and
before the timeout extension fires, which would come back and
*really* terminate the command).
comment. Check against firmware state- not loop state when enabling
target mode. Other changes have to do with no longer enabling/disabling
interrupts at will.
Rearchitect command watchdog timeouts-
First of all, set the timeout period for a command that has a
timeout (in isp_action) to the period of time requested *plus* two
seconds. We don't want the Qlogic firmware and the host system to
race each other to report a dead command (the watchdog is there to
catch dead and/or broken firmware).
Next, make sure that the command being watched isn't done yet. If
it's not done yet, check for INT_PENDING and call isp_intr- if that
said it serviced an interrupt, check to see whether the command is
now done (this is what the "IN WATCHDOG" private flag is for- if
isp_intr completes the command, it won't call xpt_done on it because
isp_watchdog is still looking at the command).
If no interrupt was pending, or the command wasn't completed, check
to see if we've set the private 'grace period' flag. If so, the
command really *is* dead, so report it as dead and complete it with
a CAM_CMD_TIMEOUT value.
If the grace period flag wasn't set, set it and issue a SYNCHRONIZE_ALL
Marker Request Queue entry and re-set the timeout for one second
from now (see Revision 1.45 isp.c notes for more on this) to give
the firmware a final chance to complete this command.
store a bitmask of whether we've set a value into ccb->ccb_h.status,
whether we're in the watchdog routine for this command now, whether
we've set a grace period for this command and whether this command is
actually done.
See comments of rev 1.45 of isp.c for more complete information.
output mailbox values we want to get back out of the chip once a mailbox
command is done. Add storage for the maximum number of output mailbox
registers to the softc.
Roll minor version number.
the handle (i.e., generation number), so we will now need a function that
will take a handle and return a flat index [ 0 .. maxhandles-1 ] for
auxillary routines that need an index to get at buddy store values
(like dma maps or xflist pointers).
device with Yarrow, and although I coded for that in dev/MAKEDEV, I forgot
to _tell_ folks.
This commit adds back the /dev/urandom device (as a duplicate) of /dev/random,
until such time as it can be properly announced.
This will help the openssl users quite a lot.
(Reported by Matthew Jacob)
- Fix a couple of __inline__ (changed to __inline).
- Check also against DT_DATA_IN phase on parity/crc error.
(Merged from Pamela Delaney's changes in the Linux driver)
- Fix support for phase mismatch handling from the C code for
the C1010 (only useful for testing issue).
- Add an asynchonous notification handler for `lost device'
(AC_LOST).
This merges in changes from NetBSD which ensure bktr0
(actually bktr%d) is printed at the start of any output lines.
Submitted by: Thomas Klausner <wiz@danbala.ifoer.tuwien.ac.at>
This is work-in-progress, and the entropy-gathering routines are not
yet present. As such, this should be viewed as a pretty reasonable
PRNG with _ABSOLUTELY_NO_ security!!
Entropy gathering will be the subject of ongoing work.
This is written as a module, and as such is unloadable, but there is
no refcounting done. I would like to use something like device_busy(9)
to achieve this (eventually).
Lots of useful ideas from: bde, phk, Jeroen van Gelderen
Reviewed by: dfr
severely stripped down compared with its predecessor, and is measurably
a _lot_ faster.
Many thanks to Jeroen van Gelderen for lots of good ideas.
There is still a problem with this; it is written as a mudule, and as
such is theoretically unloadable. However, there is no refcounting done
as I would prefer to do that a'la device_busy(9), rather than some
"home-rolled" scheme. The point is pretty moot, as /dev/null is
effectively compulsory.
Reviewed by: dfr
the PnP probe is merely a stub as we make assumptions about some of this
hardware before we have probed it.
Since these devices (with the exception of the speaker) are 'standard',
suppress output in the !bootverbose case to clean up the probe messages
somewhat.
Renamed varible dst in ray_rx to mp as it is a pointer to an mbuf.
Correctly grok addresses in data packets.
Promte a couple of RECERRs to real errors.
Rewrote intro at top of file to reflect my better understanding of how it
the memory mapping works.
Clear the DONE list and move some thoughts into the TODO list.
Remove RECERR from RAY_DEBUG
Start to use a desired network parameter structure, only used in download
code as I've realised that there are some problems with the idea.
Break up ray_rx, and move the data packet handler into a seperate function. This meant some knock on changes in ray_rx_mgt/ray_rx_ctl to do with
mbuf freeing.
Remove some debug code/XXX comments that are out of date.
Force alphas to prefer mem mapping as the default.
Basically, we have a pointer to a function which we can call which will
return us a pointer to firmware for the card we have. We call this function
(if it's non-NULL) with the address of our mdvec f/w pointer.
The way this works is that if ispfw (as a module or a static) is loaded,
it initializes the pointer in isp_pci, so we can call into to it to fetch
a pointer to a f/w set.
If ispfw is MOD_UNLOADed, it's retained a pointer to our mdvec f/w pointers,
which then get zeroed out so we don't have any references to data that's
now gone from kernel memory. Removing the f/w saves ~360KBytes.
Alas, there is no autounload mechanism that works for is here.
through, establish what our LUN width is. Unfortunately, we can't ask
the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs
(SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't
load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We
have to assume only one LUN for Fibre Channel because the LUN setting
in Request Queue entries is in different places whether we have SCCLUN
firmware or not, so the only LUN guaranteed to work for both is LUN 0.
Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used-
instead use run time determinants based upon isp->isp_maxluns.
After starting firmware, delay 500us to give it a chance to get rolling.
Fix the interrupt service routine to check for both isr && sema being zero
before thinking this was a spurious interrupt. Following the manuals,
allow for both Mailbox as well as Queue Reponse type interrupts for regular
SCSI.
(we always support fabric now). Remove SCCLUN definition (we always
support SCCLUN now, if we load the f/w). Add typedef definition of an
external firmware fetch function.
need this RSN.
Remove a pointless warning in the root device locating code.
Remove the "wd" compatibility name from the "ad" driver.
WARNING: If you have not updated to use /dev/wd* in your /etc/fstab
and modern bootblocks, it would be a very good idea to do so BEFORE
you upgrade your kernel.
Implement the Solaris way to break into DDB over a serial console
instead of sending a break. Sending the character sequence
CR ~ ^b will break the kernel into DDB (if DDB is enabled).
Reviewed by: peter
layout introduced in driver 1.5.3. The driver was
confused by the bogus TEKRAM table used to translate
user sync. setting to SCSI sync. factor.
Btw, the new TEKRAM DC-390 U3D and U3W Ultra-160
controllers seem to be using BIOS from SYMBIOS/LSI
and thus SYMBIOS NVRAM layout.
If that means that TEKRAM will now offer real
SYMBIOS software compatible SCSI controllers, then
it is a *GREAT NEWS*.
What we'd like to know is whether or not we have a listener
upstream that really hasn't configured yet. If we do, then
we can give a more sensible reply here. If not, then we can
reject this out of hand.
Choices for what to send were
Not Ready, Unit Not Self-Configured Yet
(0x2,0x3e,0x00)
for the former and
Illegal Request, Logical Unit Not Supported
(0x5,0x25,0x00)
for the latter.
We used to decide whether there was at least one listener
based upon whether the black hole driver was configured.
However, recent config(8) changes have made this hard to do
at this time.
Actually, we didn't use the above quite yet, but were sure considering it.
Generated a new macor, RAY_RECERR for reporting errors with. Verbosity set with IFF_DEBUG (recommended at present).
Add PRIBIO to tsleeps.
Catch detach on ray_ccs_alloc a little better.
Move sc_promisc into desired and current n/w parameters.
Remove IFQ_PEEK, we know the driver runs okay without it.
Drain the output queue in ray_stop.
Only use ray_mcast for ADD/DEL multi ioctls. ray_init_multi resets the
multicast list on startup. Simplifies ray_init a little.
Tidy some old comments.
ray_download_done now copies the whole desired n/w parameter set into the
current set. This is because I was missing soem parameters - like the
net type!
2. Newbusify the driver.
3. Build as a module.
4. Use correct minor numbers when creating device files.
5. Correctly lock control characters.
6. Return ENXIO when device not configured.
Submitted by: Tor Egge <Tor.Egge@fast.no>
7. Fix the baud_table.
Submitted by: Elliot Dierksen <ebd@oau.org>
Note:
- the old driver still lives in src/sys/i386/isa, so that you can
revert to it if something goes wrong.
- The module does not detach very well. Attaching works fine.
map physical addresses below 0x2000 (accoding to AMI). If we
allocate our s/g tables and get an address below this point, leak the
memory and try again.
This should fix booting from these controllers.
Get ray_detach working correctly. This is a very simple routine as it
just wakes up sleeping processes. Note that anything woken has NO softc
structure available! runq_add is suitably modified to detect a detach and
return straight away.
Due to ray_detach and its implications use a macro for adding things
to the runq in user land.
tested on Intel BX chipsets only. The other agp minidrivers are totally
untested.
The programming api is a subset of the Linux api and is only intended to
be enough for the X server to use. There is also an in-kernel api for the
use of other kernel modules such as the 3D DRI.
21143 chips, I accidentally removed the DC_MII_REDUCED_POLL flag
for all 21143 cards. This caused problems with timer-instigated
TCP retransmits, which happened to occur at the same time as an
MII poll tick on MII-based cards (e.g. D-Link DFE-570TX). Fixed this,
plus made some other cleanups. The autoneg fixes for the non-MII
cards still work. Also tested the PNIC II now that I have one again.
Fix several instances of breakage in RAID-5 revive code.
Tidy up code.
parityops:
Don't attempt to do anything if the plex is degraded or worse.
parityrebuild:
Add comments.
Perform transfers in correct length.
after autoneg so we make sure to set the link state and duplex mode
correctly.
- Make sure to set the 'ignore pause frames' bit on the XMAC.
- Small linewrap fix.
needed to add into ether_input) and finally sorting IFF_RUNNING through
whole driver.
As part of the IFF_RUNNING stuff, we've added an extra flag so callers
can request that runq routines should check IFF_RUNNING before executing.
Remove BPF taps as this is now done by ether_input.
Resurrect multicast code, moving the multicast list stuff to the runq
routine.
Dump ray_promisc_user as all flag changes are now handled by ray_init, and
add a couple of checks to ray_promisc.
In uppparams_user, allow changes before the card is running (need to
fix some breakage with _download here later). In addition, don't
assume that the current n/w parameters are valid - they are only valid
in the runq.
Fix a nasty flag bug - runq_add cleared all the flags on the last command!
Remove the hacks for setting the memory flags - problems were down
to buggy versions of pccardd. For some reason pccardd only dtrt with
the "right" debug_level.
not gone yet.
format_config: print correct text when a volume has a preferred plex.
This is still broken, but not quite as badly.
Reported-by: Phil Regnauld <regnauld@ftf.net>
Change a rather silly comment.
routines from foo_watchdog() because foo_watchdog() is called at
interrupt context, and that's a no-no due to the way the USB stack
is currently set up.
What we do now is call the TX end of frame handler manually to clear
the completed transmission, then check the send queue and send off
any frames that are pending.
Also turned off the interrupt pipe stuff in if_aue, since it appears
to tickle a bug in the USB stack that I haven't found yet.
motherboards that use YMF740's. It has a strange subvendor and subdevice
ID and requires a disturbingly long delay after the ac97 codec init.
Cameron hasn't had this driver tested on another 740 yet, so we don't know
if this is a quirk of all 740's, or if its just something about the codec
that Intel used.
workalike chips (Macronix 98713A/98715 and PNIC II). Timing is somewhat
critical: you need to bring the link as soon as possible after NWAY
is done, and the old one second polling interval was too long. Now
we poll every 10th of a second until NWAY completes (at which point
we return to the 1 second interval again to keep an eye on the link
state).
I tested all the other cards I had on hand to make sure I didn't bust
any of them and they seem to work (including the MII-based 21143 card).
This should fix some autoneg problems with DE500-BA cards and the
built-in 10/100 ethernet on some alpha systems.
(Now before anyone asks why I never noticed this before, the old code
worked just find with the Intel swich I used for testing back in NY.
Apparently not all switches are as picky about the timing.)
It may cause misterious chars appearse in the middle of the scrolled lines.
The bug trigger: enter
grep P_32 /usr/include/*.h
command and see misterious "db.\" filename.
Simple stuff
------------
Split _download up so that the MIB settings are in their own functions.
Made "tx completed but status is ..." a recoverable error
Cut down verbosity of "unloaded" messages
Moved ccs_free and com_runq from intr_ccs to ecf_done and runq_done
to avoid embarasing mistakes and waits.
Merged runq_add and runq_arr into one and called it runq_add
Made RAY_COM_DUMP a real debug called RAY_DCOM
Consistnet debugging around tsleeps.
Use bus_activate_resource for attr/cm mapping, and set the flags
correctly in the allocation routines (needs more hacks to
sys/pccard/pcic.c)
com_malloc is now seperated from the comq initialization. This was
done whilst trying to set automatic variables for the comqs.
Harder Stuff
------------
As part of the IFF_RUNNING fixes, remove the panic in runq if we are
not running.
Change, again, runq_add. This time we don't do any cleaning up
if there were errors. This is so that callers get the chance
to re-try (not that I ever see it being used).
In runq_add, only sleep when there is something to sleep on!
ioctl locking routines, stolen from awi.c but not used
Hardest Stuff
-------------
Dealing with serialing ioctls correctly means that we must QUEUE
changes to IFF_RUNNING and check it in the QUEUED commands, not
in the user commands. Whilst simple to state, it took a few
hours of head scratching to get it right. The realisation was that
I only have to guarantee that sub-commands from a single process
are serialised and "atomic", and that they check the status of the
interface flags when invoked and not when they are queued.
Another way of looking at it, is that the driver's state is stored
in the runq and the IFF_RUNNING flag. These must be changed together.
What this means practically, is that IFF_RUNNING is set after
we have started/joined/associated with a network. And it is
cleared by ray_stop via the runq so that unfinsished commands are
not distrupted.
I still have to fix up promisc, upp/repparams and mcast.
Oh yeah, stop is essentially a noop in that it only
changes IFF_RUNNING
- Get rid of a fiew uselessly `long' variables
and casts to `long'.
- Estimate the PCI clock for all chips, except
C1010 for now (we should do that for each PCI BUS)
- Refine a couple of C1010 errata work-arounds.
- For now, make sure AIP generation is disabled
for the C1010-66.
"options COMPAT_OLDPCI". This option already existed, but now also tidies
up the declarations in #include <pci/pci*.h>. It is amazing how much stuff
was using the old pre-FreeBSD 3.x names and going silently undetected.
all other modes not set ALKED flag and it means that CapsLock always turned
off for them.
Real bug example is X11 which never turn on CapsLock with Russian keyboard.
PR: 18651
Submitted by: "Mike E. Matsnev" <mike@po.cs.msu.su>
more frequently than the core part of the sio driver, it might
be good to move the PnP IDs to sio_isapnp.h or something like
that.
PR: i386/18828
Submitted by: J.P. King <jpk28@cam.ac.uk>
Make the error recovery code a little more obvious.
Inform the user if UDMA66 mode couldn't be selected due to a
non ATA66 compliant 80pin cable.
Minor cosmetics.
to various pmap_*() functions instead of looking up the physical address
and passing that. In many cases, the first thing the pmap code was doing
was going to a lot of trouble to get back the original vm_page_t, or
it's shadow pv_table entry.
Inspired by: John Dyson's 1998 patches.
Also:
Eliminate pv_table as a seperate thing and build it into a machine
dependent part of vm_page_t. This eliminates having a seperate set of
structions that shadow each other in a 1:1 fashion that we often went to
a lot of trouble to translate from one to the other. (see above)
This happens to save 4 bytes of physical memory for each page in the
system. (8 bytes on the Alpha).
Eliminate the use of the phys_avail[] array to determine if a page is
managed (ie: it has pv_entries etc). Store this information in a flag.
Things like device_pager set it because they create vm_page_t's on the
fly that do not have pv_entries. This makes it easier to "unmanage" a
page of physical memory (this will be taken advantage of in subsequent
commits).
Add a function to add a new page to the freelist. This could be used
for reclaiming the previously wasted pages left over from preloaded
loader(8) files.
Reviewed by: dillon
It's not clear what this does nor why they would do it, but it should
compile, now. This could be a case where fixing the code so that it
compiles merely masks more devious dysfunctional behaviour.
Note that __bsdi__s_/_i_/_os_/__ has moved this file to dev/ic/ and
has completely removed the non-compiling function from pdq_ifsubr.c and
has completely removed this function and placed it into netinet/if_ether.c
(if, in fact, it wasn't there the whole time). I was tempted to simply
remove this __bsdi__only__ function.
The function is arp_ifinit().
PR: kern/7903
proc pointer is believed to have been the cause of panics related to vnconfig
on top of intr-optioned NFS mounts.
Reported by: "Sean O'Connell" <sean@stat.Duke.EDU>
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
of using the MGETHDR macro all the time. When an mbuf is reused as a
header, initialize csum_flags to zero as well, so the delayed_checksum
call woks properly.
Debbugging work done by: jmas
revive_block: Correct bug introduced in revision 1.25 which caused
Add fields to vinum_ioctl_msgexcessive concurrent requests followed by
system death.
Move to using /sys/dev/ray for driver
Backport -current ray_res code - most are stubs.
Make ray_attr stuff look like currents layout.
Make attribute memory access use a macro and ripple through.
Drop FIXUP as we always need it
changes: consider a new PDB entry different if Class 3 service parameter
roles change (!!!). Do some checking as we're getting a port database
that traps whether things change while we're doing so. Handle N-port
and F-ports correctly. Fix the fabric login loop to retain a login/binding
if things haven't changed (I mean, why logout a device only to log it back
in). No longer accept, after fabric logins, garbage if we can't get a PDB
entry that matches the device we've just logged into- if it doesn't, log
it out as it is very unlikely to still be what we thought it was. Get rid
of some of the debounce loops because we could get stuck there.
Apparently the f/w has finished the command, but somehow an interrupt is
being lost. So, we just plain wedge when booting alphas.
This is a general routine we've needed for a while.
ums driver (mouse) and get the usb driver at the same time.
This also shows that
MODULE_VERSION(usb, 1);
MODULE_DEPEND(usb, usb, 1, 1, 1);
in the same module in one source file works.
functions.
If it is defined, check whether bus_alloc_resource has succeeded. If it
hasn't, it is in polled mode. Mike Nowlin reports that this change makes
the geek port (whatever _that_ is :-) work again on his machine.
Submitted by: Mike Nowlin <mike@argos.org>
so that we return failure when we've failed and succeed when we succeed.
Otherwise, users always get a sn device :-(.
PR: 18431
Submitted by: <sanpei@sanpei.org> MIHIRA Yoshiro-san
Move the code that checks the card into _probe and out of _attach and
shuffle a couple of things around in attach.
Set ifp in the variable block - catches unused variables.
of some function names, dropping the ISA bits that were never used and
removing __P
We've renamed the _pccard_ stuff as nothing else probes or attaches.
In the next commit we will move some routines around and split out some of the
structure definitions to another file.
I've dropped the SYSCTL as I never got it working. APM is gone too as it
is broken.
Note, that the attr_read/write will be in both this and NEWCARD/NEWBUS so
I've moved the prototypes to the right place.
Add a few casts.
- Reload SCNTL3 after selection from host (C1010-33).
- Reload SCNTL4 prior to any DATA OUT phase (C1010-66).
- Use max SCSI offset 31 for ST but 62 for DT.
for transmit to the adapter, not when we receive a transmit interrupt
indicating that they were sent. This fix now allows tcpdump to produce
sane results by recording the timestamp at the point where the mbuf was
actually transmitted.
can use all of the s/g entries available on smaller cards. This is
necessary if we want to be able to handle a non-page-aligned 64k transfer
on 2.x and 3.x firmware.
Fix a missing splx() that may have left us at splbio() for longer than
desired.
Reduce shadowing of controller-supplied parameters a little.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
which seems to correspond better with what a busy plex needs. This
may also help us avoid race conditions when expanding the table which
may have been contributing to the random corruption, panics and hangs
we've been seeing in RAID-5 plexes, particularly with ata drives.
Eagerly-awaited-by: sos
Get counting volume I/Os right.
launch_requests: Be macho, throw away the safety net and walk the
tightrope with no splbio().
Add some comments explaining the smoke and mirrors.
Remove some redundant braces.
sdio: Set the state of an accessed but down subdisk correctly. This
appears to duplicate an earlier commit that I hadn't seen.
Get counting volume I/Os right.
Count buffer sizes correctly for architectures where ints are not 32 bits.
complete_rqe: Move decrementing active count until after call to
complete_raid5_write, thus possibly avoiding a race condition.
Suggested-by: dillon
Rename user bp to ubp to avoid confusion.
Tidy up comments.
a struct buf. Don't try to examine B_ASYNC, it is a layering violation
to do so. The only current user of this interface is vn(4) which, since
it emulates a disk interface, operates on struct bio already.
ioccom.h defines only implementation detail, and should therefore
only be included from the #include which defines the ioctl tags,
in other words: never include it from *.c
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
coming later this week. Mitsuru IWASAKI provided a patch to -mobile which
I used to make sure I was doing the right thing but only a small part of
the actual patch was used.
that fails to proberly close the disk.
The problem seems to be that the HP burners sometimes return
ready when they actually are not, the solution is to not use
immediate mode on the closing commands. This is suboptimal
for real burners, in that they now hog the ATA bus for possibly
minutes, where its really not nessesary, *sigh*.
not u_long. On i386's with 64-bit longs, returning u_longs indirectly
in (more than) the space reserved for uintptr_t's tended to corrupt the
previous frame pointer in the stack frame, so it was not easy to debug.
The type mismatches are hidden by the bogus cast in DEVMETHOD().
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
53C810 non 'A', 53C815 and 53C825 non 'A' are now
attached by the driver (by default).
The driver uses a different SCRIPTS set based on
MEMORY MOVE instructions for these chips.
2 SCRIPTS sets (firmwares) numbered #1 and #2 are
used for the whole support of the 53C8XX family
to get possible:
- FW #1 : Only based on MEMORY MOVE instructions.
Selected for 810, 815, 825.
- FW #2 : LOAD/STORE based. This is the firmware
also used by previous driver versions.
Selected for other chips.
When both `ncr' and `sym' are configured, `sym'
will now attach all the 53C8XX devices by default.
Previous balancing between `ncr' and `sym' can be
preserved by:
- Either editing sym_conf.h and commenting the
following compile option:
#define SYM_CONF_GENERIC_SUPPORT
(This also saves about 3.5Kb of kernel memory).
- Or setting kernel config option
SYM_SETUP_LP_PROBE_MAP to 64 (bit 0x40)
first. This will fix a few cards that hang on the WD probe. He tells
me that PAO went one step farther and removed the WD proble completely
and none of the cards in the 2.x database broke in PAO3. Since I'm
more conservative in this code, I'm just swapping the order, which he
said also fixed his problem.
Reviewed by: mdodd, iwasaki
Submitted by: sanpai@sanpai.org
The makefile contains a reference to /sys/dev/ppbus. What really should
be done is copy the header files to /usr/include/sys/dev/ppbus.
PR: kern/16767
Submitted by: Jin Guojun (FTG staff) <jin@gracie.lbl.gov>
This driver should support both the SSI (V.35 etc) E1/T1 unchannelized,
DS3 and HSSI cards. Only tested on the SSI card.
More info at: http://www.lanmedia.com
Thanks to LanMedia for donating two LMC1000P cards.
if_de.c driver modified by: LanMedia
NetGraphification by: Stephen Kiernan <sk-ports@vegamuse.org>
in struct bio. Eventually, bio_offset will probably obsolete the
bio_blkno and bio_pblkno fields.
Remove the special hack in atapi-cd.c to determine of bio_offset was valid.
that seems to be working (I have a MF card that has a 336 modem and
ethernet that the probe routine finds, but the attach fails on because
pccardd doesn't do what you'd like with MF cards all the time).
Removed NETBSDTX spares.
Renamed a load of functions - specifcally
start -> tx
init has download, sj and assoc as sub-functions
report_params and update params move to repparams/upparams
Tidied up old #define's
Got rid of old DPRINTF, made printf's RAY_PRINTF and panic's RAY_PANIC
All code KNF
Removed checking the ECF_TO_HOST area in ray_init - this gets hosed
when someone updates/read a parameter from the card so causes
unneeded grief. This required moving the tib check into ray_attach.
Changed handling of interface flags in ioctl so that promiscous mode
changes are only done as needed.
Sequences of comq entries can be added to an array and automatically
dealt with - used in ray_init_user and others.
Moved IFF_RUNNING checks from the comq commands to com_runq - still
not sure what to do so we PANIC - will be fixed.
ray_sj now checks to see if any of the parameters it can update can be
updated.
ray_sj_done now updates parameters to the current n/w set if we changed
them earlier. I was being a bit thick in earlier comments as to why this
check was done - the ECF never changes the parameters.
Assocication with APs is handled outside of ray_sj - need to add
WEP stuff if I ever get my hands on an AP.
ray_stop, ray_unload and ray_reset are currently broken - reset isn't used anyway.
ray_tx_XXX and ray_rx only have cosmetic changes.
Interrupt handler now gets command out of ccs. This is so ray_intr_ccs and
ray_intr_rcs don't need to remap CM (I'm trying to roll things up a bit as
it must be slowing us down).
ray_intr_ccs just vectors commands to functions or error checks - a
jump table could replace it in ray_intr.
Ditto for ray_intr_rcs.
mcast is currently broken - I need to do more work for ALLMULTI etc. This is reasonably easy to fix becuase of the comq array stuff.
Added a few more checks into repparams so that it is firmware version aware. It also uses the new comq framework.
Parameter updating is also much better with the update parameter return routine re-worked.
Added a couple of runq entry helper functions - one that malloc's a new
entry and fills it in with sensible defaults and another that adds and
runs a seqencue of entries.
booting on a RAID volume.
- Change 'id_foo' and 'idfoo' to 'idad_foo' and 'idadfoo'. This makes
names more consistent with the devices that the code belongs to (more
in line with the style used in the amr/mlx driver.)
Reviewed by: jlemon
- Break out the support for the XMAC II's PHY into an miibus driver.
- Reorganize the probe/attach stuff using newbus. Each XMAC is now
attached to the parent GEnesis controller using newbus. This is
necessary since each XMAC must also have an attached miibus, and
the miibus read/write register routines need to be able to get
at the softc struct for each XMAC, not the one for the parent
controller. This allows me to get rid of the grotty code I added
for selecting the unit numbers for the ifnet interfaces: the unit
numbers are now derived from the newbus-assigned unit numbers,
which should track with the ifnet interface numbers. I think.
At the very least, there should never be any collisions.
- Add support for the SK-9821 and SK-9822 1000baseTX adapters. Special
thanks to SysKonnect for loaning me two adapters for testing.
Working download and start/join network. What's nice is that I didn't touch
TX or RX code at all.
Not fully done yet - stubs for assoc, cast, promisc and user param updating. I
can't work out the "nicest" way to get the mcast and promisc interactions
sorted without needing to abort runq commands half way through. And, as
mcast/promisc used elsewhere I want to get this right.
Other stuff
Fancy new debugging with __FUNCTION__ and __LINE__.
Lots of panic's inserted until I check some stuff out.
Removed all of the old scheduler.
Removed start join timeout as I don't need it.
Removed the promiscuous broadcast code that waas ifdef'd out.
New CCS allocation
where we can have targets (based on topology).
Much more importantly, make sure all mods to isp_sendmarker or |= so
we don't lose the marking of a bus that needs to have a marker sent for it.
require full logins after a LIP, which always led to loop resets, and
various other perturbations.
Update 2200 f/w from 2.01.00 release to 2.01.09 release.
- Free resources in all the possible attachment failure cases.
One critical bugfix:
- Fix a race where it was possible to get out of synch with the log
messages from the controller, if the controller hung up for any
period of time (eg. while resetting a SCSI bus). This would result
in an endless string of console errors, bringing the machine to a
halt.
o Modify xe driver to use this.
There's still some issues with this code, so xe can't map the cis just
yet. I'm thinking about how to resolve the issue. pccard_nbk's
pccard_alloc_resource is getting in the way.
I've done this by having requests to allocate memory propigate up the
tree. We'll see how well this works and reevaluate if it isn't
working well. Also initialize ptr in the tuple. As well as minor
reorg of memory allocation. Likely need to do similar things for I/O
when the time comes.
I've move all defines from pccardchip.h into pccardvar.h and
eliminated pccardchip.h.
source address when receiving frames (and keep using address 2 when in
pseudo-IBSS mode). This is apparently necessary in order to obtain the
true MAC address of the sending station which is needed for PPPoE.
Patch supplied by: Blaz Zupan <blaz@amis.net>
multi-firmware support. This patch just changes
numerous names in the driver sources and is actually
nilpotent. This has been checked by comparing the
generated assembly code.
The names that have been changed are related to the
script names. They were named `script' and `script H'.
They are now named respectively `script A' and
`script B'.
before I rip out the scheduler - whilst v. nice 'n all, it is doing the
wrong job. We need something that sends commands to the card atomically
so dhcp etc. works right.
I've renamed and moved a lot of the scheduler code so that it is all
in one place and all starts with ray_cmd_
ray_stop has some debugging crap left in - to be deleted rsn
support. Changes are rather simplifications of the SCRIPTS
interface (prior to complexifying it again;) ), dead code
removes and comment fixes.
Code removed:
- Handling of kernel variables referenced from SCRIPTS.
- Handling of selection without ATN.
Slightly rewritten:
- Handling of illegal phase (4/5) and data overrun conditions.
Simplifications:
- Extended error flag and bits now only set from the C code.
- Move the extended error status (xerr_status) and nego
status (nego_status) outside the data structure accessed
by SCRIPTS (struct dsb).
- Get rid of the script status field (scr_st).
- Only patch SCR_NO_OP SCRIPTS instructions to adapt SCRIPTS
to actual chip capabilities.
Cosmetic changes:
- Miscellaneous comments in SCRIPTS.
- FreeBSD_4_Bus define replaced by FreeBSD_Bus_Io_Abstraction.
Exceptions:
Vinum untouched. This means that it cannot be compiled.
Greg Lehey is on the case.
CCD not converted yet, casts to struct buf (still safe)
atapi-cd casts to struct buf to examine B_PHYS
incorrectly attach itself to ThunderLAN adapters which happen to have
a PHY who's model number happens out to be 0.
Problem reported by: Peter L. Thomas <Pete@painless-computing.com>
(which is actually a CATC Netmate).
Gee. I don't know why people make such a fuss over supporting USB ethernet
NICs. This is easier than collecting graft.
in attach.
- Change a EISA_CHANNEL_CLEAR to EISA_CHANNEL_BUSY in ida_v1_submit().
This may fix the problem with EISA IDA adapters though we have not heard
back from testers yet.
Reviewed by: jlemon
o Eliminate cross calls between the devices. Instead move to using the
newbus messaging system. Added three new card calls: attach_card,
detach_card, get_type.
o Eliminate interrupt routine in pccard we never use.
o Move from deactivate to detach for removing cards.
o Start mapping CIS memory, but it is broken and causes panics. At least
it is closer to working than before.
o Eliminate struct device everywhere. It was bogus.
o Initialize softc for pccard device so we have valid pointers to
ourselves.
o Implement routine to find the pcic ivar for a child device of the pccard so
we can use it to talk to the pcic hardware.
o Lots of minor tiding up.
This version now panics when we try to read the CIS. The next batch
of work to make this work is what was outlined in my posting to mobile
about resource allocation and such.
- implement user-initiated background drive rebuild
- implement user-initiated background consistency check
- log controller-initiated background rebuild/check operations
Try to fix the elusive "invalid log operation" bug, and panic if we do
hit this one in the hopes of getting better information.
Tidy up diagnostic messages.
Try to use disk_create/disk_destroy correctly. This isn't working
properly yet, but it's not clear whose fault that is.
robust enough to work with dhcp. Essentially the driver returns to userland
before certain commands have been completed by the card. I'm trying to
work out the best way to fix this. There are very minor functional changes,
most of this is debugging.
Rework of debugging so a bit mask is used and re-allocation around the place.
Tried to protect ray_init with a tsleep until the network has been joined. I think this is only a partial fix as we also update the mcast and promisc
values.
Update the license in the rio_usb.h (now rio500_usb.h) to not be GPL.
Sorry for committing that file in the first place. The change of license
was agreed to by the original author.
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
- Add support for ISA based DPT adapters (this doesn't quite work yet).
- Sync dpt_eisa.c with my local copy.
- Simplify how EISA IDs are matched.
- Prototype.
- Formatting nits.
- Conform to how I do things in dpt_pci.c/dpt_isa.c.
- Modify dpt_scsi.c:dpt_alloc() to DTRT with newbus.
- Add some comments to dpt_scsi.c:dpt_pio_get_conf().
- Add additional check to dpt_scsi.c:dpt_get_conf().
- Add some useful error messages to dpt_scsi.c:dpt_init().
request could be deallocated before the top half had finished
issuing it. The problem seems only to happen with IDE drives
and vn devices, but theoretically it could happen with any
drive. This is the most important part of a possible series
of fixes designed to remove race conditions without locking
out interrupts for longer than absolutely necessary.
Reported-by: sos
Fix-supplied-by: dillon
From the README:
Any IEEE 802.11 cards use AMD Am79C930 and Harris (Intersil) Chipset
with PCnetMobile firmware by AMD.
BayStack 650 1Mbps Frequency Hopping PCCARD adapter
BayStack 660 2Mbps Direct Sequence PCCARD adapter
Icom SL-200 2Mbps Direct Sequence PCCARD adapter
Melco WLI-PCM 2Mbps Direct Sequence PCCARD adapter
NEL SSMagic 2Mbps Direct Sequence PCCARD adapter
Netwave AirSurfer Plus
1Mbps Frequency Hopping PCCARD adapter
Netwave AirSurfer Pro
2Mbps Direct Sequence PCCARD adapter
Known Problems:
WEP is not supported.
Does not create IBSS itself.
Cannot configure the following on FreeBSD:
selection of infrastructure/adhoc mode
ESSID
...
Submitted by: Atsushi Onoe <onoe@sm.sony.co.jp>
connected during boot and the vpo module is in the kernel/loaded.
In the case where the module is loaded at some later stage with kldload,
the CAM bus is now rescanned as well.
- The driver now uses bus_space() and runs on NetBSD 1.4.2
Submitted by Thomas Klausner <wiz@danbala.ifoer.tuwien.ac.at>
- Remove startup quirks for video and vbi capture for PAL users.
PAL TV users can now run FXTV and Alevt in any order.
- Add support for cable channels >100
Submitted by Scott Presnell <srp@zgi.com>
- New MSP3410/3415 setup code added. This is experimental.
Please set the sysctl hw.bt848.slow_msp_audio to 1 for this.
Submitted by Frank Nobis<fn@radio-do.de>
Pass sc->dev rather than a bogusly cast pccard_softc *sc.
This allows us to insert and remove cards w/o panicing the kernel.
However, the cis isn't mapped in, so the pccard_scan_cis function
fails.
- Request the maximum number of LUNs on a device if it is
a Bulk-Only device.
- Handle NO_TEST_UNIT_READY case for SCSI
- Add NO_START_STOP quirk for LS-120
- Fix a KASSERT which was the wrong way around.
- Kickstart the LS-120 with the infamous LS-120 specific command of
which no one knows what it doesn, apart from the fact that it appeared
in the Linux code someday.
kernel. Justin agress that there is no other reasonable alternative to
do automatic rescans on connect.
The problem is that when a new device attaches to a SIM (SCSI host
controller) we need to send a XPT_SCAN_BUS command to the SIM using
xpt_action. This requires however that there is a peripheral available
to take the command (otherwise xpt_done and later bomb). The RESCAN
ioctl uses the same periph.
This enables a USB mass storage drive to do an automatic rescan on
connection of the drive.
The automatic dropping of a CAM entry on disconnection was already
working (asynchronous event).
The next thing to do is find someone to commit a change to vpo to do the
same thing. Just port umass_cam_rescan and friends across to that
driver.
Approved by: gibbs
unit numbers all wrong. This did not show up because most of them where
zero anyway.
Use a separate buffer for command transforms instead of fiddling with
the existing cdb_bytes.
Take CAM_CDB_POINTER into account. Nobody is using it, but someone might
in the future.
Be more picky about what to accept in the UFI command set.
First attempt at implementing the ATAPI command protocol transforms.
This should at least make Imation Superdisk and other e-Shuttle based
devices show as attached. Maybe they even work to some extent.
(Much of this done by script)
Move B_ORDERED flag to b_ioflags and call it BIO_ORDERED.
Move b_pblkno and b_iodone_chain to struct bio while we transition, they
will be obsoleted once bio structs chain/stack.
Add bio_queue field for struct bio aware disksort.
Address a lot of stylistic issues brought up by bde.
contains the ADMtek Pegasus AN986 USB chipset. The
adapter supports both 10BaseT and 100BaseT (including
full-duplex). The product code for these adapters is
0x2206.
introduced in FreeBSD-4.0. The driver is now full up-to-date
with regards to the current kernel interfaces.
Another significant change in this driver version applies
to the checking of the data direction. The driver is now
able to check against the expected data direction in any
circumstance and will not hang either if direction is wrong
at the start of the IO, or if for some weird reason,
the device changes to the wrong direction during the IO.
This driver version is still usable under FreeBSD 3.2/3.3,
since it only requires CAM, other kernel interface dependencies
being #if'ed in the sources according to kernel version.
But, in order to use the driver under those early kernel
versions, user has to move the driver sources by hand and make
appropriate tiny changes to let the kernel know about the driver.
Other changes:
- Remove the debugging stuff for WSR bit.
- Get rid of some warnings about volatile being discarded.
which think they know the IntelliMouse 4-byte packet and believe,
wrongly, that any other protocols use 3-byte packets.
- Update a couple of comment lines for A4 Tech mice.
conf/files
i don't seem to be clearing the cache right resulting in a short initial
burst of noise, despite doing the same as creative and alsa. i'm committing
now so more eyes can pore over the code.
and has not been loaded via a kldload,
running usbd(8) will autoload the "usb.ko" kld.
thanks to Peter Wemm for enlightening me on the
differences between kldfind(2) and modfind(2).
doesn't support winmodems, softmodems, hcf or any other modem that
relies on the host to do any sort of soft control for any aspect of
the modem's function. There are two modems known to work:
3COM FaxModem PCI.
ActionTec 56k VoiceMessaging PCI Modem
and the following modem might work
Multitech PCI FaxModem (not sure about this)
and the serial pci cards might work too. I have neither these
hardware items so I can't add support for them.
- Add periodic status monitoring routine. Currently just detects
lost commands, further functionality pending data from AMI.
Add some new commands states; WEDGED (never coming back) and
LATE (for when a command that wasmarked as WEDGED comes bacj,
- Remove a number of redundant efforts to poll the card for completed
commands. This is what interrupt handlers are for.
- Limit the maximum number of outstanding I/O transactions. It seems
that some controllers report more than they can really handle,
and exceding this limit can cause the controller to lock up.
- Don't use 'wait' mode for anything where the controller might not
be able to generate interrupts. (Keep the 'wait' mode though sa it
will become useful when we start taking userspace commands.
- Use a similar atomic locking trategy to the Mylex driver to prevent
some reentrancy problems.
- Correctly calculate the block count for non-whoile-bloch transfers
(actually illegal).
- Use the dsik device's si_drv1 field instead of b_driver1 in the
buf struct to pass the driver identifier arond.
- Rewrite amr_start and amr_done() along the lines of the Mylex driver
in order to improve robustnes.
- Always force the PCI busmaster bit on.
- Move dev/aic/aic_isa.c entry from conf/files to conf/files.MACHINE
because PC-98 uses different file.
Submitted by: nyan and IMAI Takeshi <take-i@ceres.dti.ne.jp>
fe_read_eeprom_rex() and fe_init_rex(). These functions should be
useful for REX-5580 series (for PC-AT). But they are included in
`#ifdef PC98' to avoid warnings by unused static functions. If you
try to support REX-5580, please be aware of these functions.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
rewrite ess mixer to use native registers
rewrite play/rec code to use more accurate timer when available
add code to use audio2 for playback, but disable it as no irqs are generated
to be based on the transfer speed, but I got it all wrong. The by far
biggest factor in the timeout is the start of a removable device, which
is about 2 seconds anyway.
Prodded by: Lennart Augustsson
address size that is different than the standard 6bits. This fixes
support for the Compaq NC3121 card, certain newer Intel Pro/100+
cards, and should also fix integrated NICs on SuperMicro and Compaq
motherboards.
The auto-sizing algorithm was taken from NetBSD (thanks!), which I
think got it from Linux originally.
Thanks also to Andrew Sparrow <spadger@best.com> and Joe Moore
<jomor@ahpcns.com> for supplying me with unworking Compaq and Intel
cards to develop and test the fixes with.
set properly in the struct buf with vinum:
Fix locations where B_READ was cleared in the old code but
b.b_iocmd wasn't set to BIO_WRITE
Fix propogation of b_iocmd
Correct comments to reflect reality
Don't compare b_flags with BIO_READ, it's in b_iocmd.
Submitted by: Bernd Walter <ticso@cicely.de>
Remove RF_PCCARD_ATTR in anticipation of removing it from sys/rman.h
Add interface for setting "attributes" of pccard/cardbus devices.
Minor formatting nits.
timeout closer to the 1-second value that AMI use in their Linux
driver, and mark the mailbox structures as volatile so that gcc
doesn't over-optimise access to them.
This should fix the "controller wedged" bug.
Submitted by: Brian Dean <brdean@unx.sas.com>
* add a callback for initialising the mixer interface
* support ac97 2.1 variable rate audio feature
fix ac97-using drivers for the above
add suspend/resume support for neomagic
Make the public interface more systematically named.
Remove the alternate method, it doesn't do any good, only ruins performance.
Add counters to profile the usage of the 8 access functions.
Apply the beer-ware to my code.
The weird +/- counts are caused by two repocopies behind the scenes:
kern/kern_clock.c -> kern/kern_tc.c
sys/time.h -> sys/timetc.h
(thanks peter!)
substitute BUF_WRITE(foo) for VOP_BWRITE(foo->b_vp, foo)
substitute BUF_STRATEGY(foo) for VOP_STRATEGY(foo->b_vp, foo)
This patch is machine generated except for the ccd.c and buf.h parts.
field in struct buf: b_iocmd. The b_iocmd is enforced to have
exactly one bit set.
B_WRITE was bogusly defined as zero giving rise to obvious coding
mistakes.
Also eliminate the redundant struct buf flag B_CALL, it can just
as efficiently be done by comparing b_iodone to NULL.
Should you get a panic or drop into the debugger, complaining about
"b_iocmd", don't continue. It is likely to write on your disk
where it should have been reading.
This change is a step in the direction towards a stackable BIO capability.
A lot of this patch were machine generated (Thanks to style(9) compliance!)
Vinum users: Greg has not had time to test this yet, be careful.
too many, so I removed the checks for the valid OUIs. We already do a
checksum of the entire ethernet address, so extra checking against the
OUI shouldn't be needed.
it's options COMPAT_OLDISA and COMPAT_OLDPCI. This is meant to be a
fairly strong incentive to update the older drivers to newbus, but doesn't
(quite) leave anybody hanging with no hardware support. I was talking with
a few folks and I was encouraged to simply break or disable the shims but
that was a bit too drastic for my liking.
prevent a page fault if the card is ejected while BPF is in use. This
could happen if DHCP or tcpdump was in use on that interface during
ejection. Other drivers may also require this modification.
Reviewed by: wes
negotiation features (DT, ULTRA2, ULTRA, FAST). The offsets
where not properly updated when the DT entry was added and so
the driver could attempt to negotiate a speed faster than that
supported by the target device or even requested by the user
via SCSI-Select settings. *
o Update the target mode incoming command queue kernel index value
ever 128 commands instead of 32. This means that the kernel will
always try to keep its index (as seen on the card - the kernel may
actually have cleared more space) 128 commands ahead of where the
sequencer is adding entries.
o Use the HS_MAILBOX register instead of the KERNEL_TQINPOS location
in SRAM to indicate the kernel's target queue possition on Ultra2
cards. This avoids the "pause bug" on these cards and also turns
out to be much more efficient.
o When enabling or disabling a particular target id for target mode,
make sure that the taret id in the SCSIID register does not
reference an ID that is not to receive target selections. This
is only an issue on chips that support the multiple target id
feature where the value in SCSIID will still affect selection
behavior regardless of the values in the target id bit field
registers.
o Remove some target mode debugging printfs.
o Make sure that the sense length reported in ATIO commands is
always zero. This driver does not, yet, report HBA generated
sense information for accepted commands.
o Honor the CAM_TIME_INFINITY and CAM_TIME_DEFAULT values for
the CCB timeout field.
o Make the driver compile with AHC_DEBUG again.
* Noticed by: Andrew Gallatin<gallatin@cs.duke.edu>
-current. It doesn't work yet as stable as the 3.x/PAO version of the
driver does, however, i get occasional `FDC direction bit not set' and
other weird messages, but it basically works at least.
The old (defunct) #ifdef FDC_YE stuff has been eliminated completely
now, PCMCIA-FDC specific functions have been implemented differently
where needed.
Unfortunately, due to the fact that the traditional PeeCee FDC with
its funny non-contiguous register space (one register for WD1003
harddisk controllers is interleaved into the FDC register set), and
Peter's subsequent changes involving two different bus space handles
for normal FDCs, the changes required for the Y-E stuff are more
complex than i'd love them to be. I've done my best to keep the logic
for normal FDCs intact.
Since the Y-E FDC seems to lose interrupts after a FDC reset
sometimes, i've also replaced the timeout logic in fd_turnoff() to
generate an artificial pseudo interrupt in case of a timeout while the
drive has still outstanding transfers waiting. This avoids the total
starvation of the driver that could be observed with highly damaged
media under 3.x/PAO. This part of the patch has been revied by bde
previously.
I've fixed a number of occasions where previous commits have been
missing the encapuslation of ISA DMA related functions inside
FDC_NODMA checks.
I've added one call to SET_BCDR() during preparation of the format
floppy operation. Floppy formatting has been totally broken before in
3.x/PAO (garbage ID fields have been written to the medium, causing
`wrong cylinder' errors upon media reading). This is just black
magic, i don't have the slightes idea _why_ this needs to be but just
copied over the hack that has been used by the PAO folks in the normal
read/write case anyway.
The entired device_busy() stuff seems to be pointless to me. In any
case, i had to add device_unbusy() calls symmetrical to the
device_busy() calls, otherwise the PCMCIA floppy driver could never be
deactivated. (As it used to be, it caused a `mark the device busier
and busier' situation.) IMHO, all block device drivers should be
marked busy based on active buffers still waiting for the driver, so
the device_unbusy() calls should probably go to biodone(). Only one
other driver (whose name escapes me at the moment) uses device_busy()
calls at all, so i question the value of all this...
I think this entire `device busy' logic simply doesn't fit for PCMCIA
&al. It cannot be the decision of some piece of kernel software to
declare a device `busy by now, you can't remove it', when the actual
physical power of removing it is the user pulling the card. The
kernel simply has to cope with the removal, however busy the device
might have been by the time of the removal, period. Perhaps a force
flag needs to be added?
Upon inserting the card a second time, i get:
WARNING: "fd" is usurping "fd"'s cdevsw[]
WARNING: "fd" is usurping "fd"'s bmaj
I suspect this is related to the XXX comment at the call to
cdevsw_add(). Does anybody know what the correct way is to cleanup
this?
- Microsoft IntelliMouse Explorer: 2 buttons on top, 2 side buttons
and a wheel which also acts as the middle button. The mouse is
recognized as "IntelliMouse Explorer".
- Genius NetScroll Optical: 2 buttons on top, 2 side buttons and a
wheel which also acts as the middle button. The mouse is recognized
as "NetMouse/NetScroll Optical".
- MouseSystems SmartScroll Mouse (OEM from Genius?): 3 buttons on top,
1 side button and a wheel. The mouse is recognized as Genius
"NetScroll".
- IBM ScrollPoint: 2 buttons on top and a stick between the buttons.
The stick can perform "horizontal scroll" in W*ndows environment.
The horizontal movement of the stick is detected. It is currently
mapped to the Z axis movement in the same way as the first wheel.
The mouse is recognized as "MouseMan+", as it is considered to be
a variation of MouseMan.
- A4 Tech 4D and 4D+ mice. These mice have two wheels! The movement
of the second wheel is reported as the Z axis movement in the
same way as the first wheel. These mice are recognized as "4D
Mouse" and "4D+ Mouse".
- Tweak IntelliMouse support code a bit so that less-than-compatible
wheel mice can work properly with the psm driver.
- Add driver configuration flags which correspond to the kernel
options PSM_HOOKRESUME and PSM_RESETAFTERSUSPEND, so that we don't
need to recompile the kernel when we need these functions.
- Properly keep track of the irq resource.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).
- Properly keep track of resources (I/O ports and irq).
- Use bus_space_read/write() to access the ports.
- Add PnP IDs.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).
this version include:
- Support for version 2.x firmware (2.42 or later recommended). This
means we are the only open-source driver supporting these adapters.
This code has only been tested on a Digital KZPCA adapter in an Alpha
system, but is believed to be correct. NOTE: EISA adapters are not
yet supported.
- Support the BIOS/Firmware initialisation handshake protocol. This
allows the driver to bring the card up to operational state even if
the BIOS can't be run (eg. if it's an x86 BIOS in an Alpha system).
- A working command pasthrough interface. This allows a user-space
configuration tool (under development) to issue arbitrary commands
to the controller or to devices in the system.
platform we're running on so we know how many bits to reserve at the top
end for the 'hose' value. It turns out that there's *just* enough room
to support all possible hoses on TurboLaser.
Reviewed by: gallatin@freebsd.org, dfr@free3bsd.org
This makes it possible to handle the done queue even when the end of tail
TD has ended up on the done queue as well (the xfer in this case is NULL
but the next field is valid, so we simply skip that element.
Make sure we mark all the handled transfers as handled.
Stop using powerhooks. They are a NetBSD-ism.
rest of the code in (so changing media actually works.)
Add a few more register definitions for use with this and other new code.
Print a few details in the probe message; this should be useful in
bug reports and such but should not add to the clutter.
* i needed it anyway
* remove startccs and startcmd - done
* as those were used for the NetBSD start timeout
* multicast - done but UNTESTED
* I don't have the ability/facilty to test this
* rxlevel - done
* stats reported via raycontrol
* getparams ioctl - done
* reported via raycontrol
* start_join_done needs a restart in download_done - done
* now use netbsd style start up
removed spare timerh
implemented start_assoc in ray_ccs_done
bit more knfing
we get the com address. If so, we go ahead and return. Bruce thinks
there's a bug in the pccard layer that it terminates devices with
extreme prejustice rather than letting them deside for themselves when
to terminate (and he's likely right). This fix doesn't change that,
but instead works around it by checking for NULL pointers at more
places than before.
The detach routine still calls functions at interrupt level that
aren't reentrant. In theory this could cause a problem, but none
showed up in practice. Future versions should correct this problem,
likely by making the detach process a thread/process at the pccard
level. NEWCARD will do this, and the current pccard layer should
likely be modified to that as well, should it live long enough.
A few style nits of the same form that were in my original patch sent
off to bde were also fixed as part of this process. Mostly use of
!ptr and return ENOPARENS.
This should prevent a crash on suspend with an active ppp link as
well, but that wasn't tested.
Reviewed by: bde
Approved by: jkh
requires current and desired network parameters, so I have created a network parameter structure and used two on them in the softc. This gives a bit of room of expansion. Re-wrote the update check in _net to work with this.
Tidyed up softc due to above.
Removed startccs and startcmd as they were only used by NetBSDs startup timeout.
keyboard port and interrupt is enabled and the driver is attached even
when the keyboard itself is not present when the system is booting.
(This has been the behavior through out 2.X and 3.X, but is somehow
broken in 4.0.)
# I certainly don't recommend people to `hot-plug' the AT keyboard,
# because the interface isn't designed for hot-plugging and such act
# will often break the keyboard controller. But, so many people want to
# do that anyway...
Approved by: jkh
not actually used yet. This created a lot of prototypes.
I moved code around so that the functions are in the same order as NetBSD - this helps diff a lot.
Things that are missing are the TX routine and ifmedia stuff and ioctls
Not all of the stuff is enabled - we are missing calls in ccs_done and ioctl.
Promiscious mode is working.
Am almost ready to use the NetBSD start up routine - essentially all I need
to do is not use a seperate timer to call download_timo.
Other misc. things:
callout_stop is a newish feature for cancelling a timer without
argument checking it.
tried to add a sysctl knob but it doesn't work in the module
enabled infrastructure code to call netbsd bits.
Change disk names to `idad' to avoid naming conflicts with the controller,
and enable the new disk code to pick up the drives.
Tested by: david.w.james@bt.com (existing compaq support)
Reviewed by: msmith
Approved by: jordan
channel DMA. The problem was that the SDC bit (0x04) can only be set in
the MCE state.
PR: kern/16587
Submitted by: Matthew Reimer <mreimer@vpop.net>
Approved by: jkh (in person)
card configuration hassles.
Added a TODO list so I don't forget to finish stuff.
Tidyed up a lot of XXX.
Tidy'd and documented debugging - all DPRINTF have a debug level associated.
RAY_DEBUG = 1, will log packet errors.
#if protect common memory hacking
Don't rely on pccardd for common memory settings.
Added a simple transmit mode - reasonable performance but not great. Will do a version of the NetBSD chained buffers soon. Yup we have two way transmisson!
Fix a stupid bug in the common memory code - the ioctl call was
hidden behind a debug test!
from panicing when disconnecting a USB Wacom Graphire tablet.
jhk approved the fix some time ago, but I forgot to actually commit the
thing.
Reported by: Dirk van Gulik <dirkx@webweaving.org>
Approved by: jhk
is responsible for this and this will lead to malloc 'freeing already
free' type panics. One was in the probe code, the other was in the
pccard eject? code.
Not explicitly approved by: jkh (but the first is fallout from subr_bus.c
rev 1.54 which was an approved commit, the second is the same problem)
adw_pci.c:
Update comments describing supported chips/cards.
adwcam.c:
adwlib.c:
adwlib.h:
Handle more error return codes from the firmware.
Break out the bus reset code into its own function.
Usa a constant for the bus reset hold delay.
Fix an interrupt race problem in adw_idle_cmd_send by
incorporating the poll loop for command completion.
Approved by: jkh@FreeBSDorg
to us, subr_bus.c will free it. This bug (panic: freeing already free)
was exposed by kern/subr_bus.c rev 1.54
Not explicitly approved by: jkh (but this is a showstopper and fallout of
the above approved change)
transferred, do it in complete_rqe instead.
launch_requests: Replace the inadvertently removed splbio() around the
main loop. It may not be necessary, but the biggest
test of this stuff are IDE disks, which I'm not
using.
Remove throttling code, I'm pretty sure it's not
needed any more.
Don't set B_ORDERED, it's not necessary either.
Objected-to-by: alfred
build_rq_buffer: Don't lose the B_ORDERED bit, it still has some
residual meaning. To do this right, Vinum needs to
look at the B_ORDERED bit and order the transfer
across all disks involved. That's an exercise for
another day.
Objected-to-by: alfred
Implicitly-sanctioned-by: jkh
The driver constructs a fake disklabel that makes the 'a' partition
cover the entire DVD-RAM disk. This cannot be changed from the user
side. This solution was chosen because most DVD-RAM will have a
UDF (or until we have that CD9660) filesystem on it covering the
entire disk, its not really thought as a real random access device.
This might change over time, but for now this is what we have, and
it is compatible with CDROM's etc, that makes using the minidisk
subsystem less than ideal, because of !modulo BDEV_SIZE blocks.
VINUM_BDEV_MAJOR and VINUM_CDEV_MAJOR respectively.
Set DRIVE_MAXACTIVE and VINUM_MAXACTIVE to 30000, effectively
disabling the request limitation code. This code was added as an
attempt to escape from a bug which seems to have gone away, and it's
very likely I'll remove the code Real Soon Now, but I don't want to do
it just yet.
struct drive: Remove references to vnode pointers, including debug
output. Vinum now talks directly to the device driver. Instead, add
a dev_t.
enum plexorg: Add an instance for RAID-4.
Change checks for striped or RAID-5 plexes to a macro 'isstriped',
which now also includes RAID-4.
Change checks for RAID-5 plexes to a macro 'isparity', which now also
includes RAID-4.
Approved-by: jkh
set_sd_state: update the state of a subdisk in a multi-plex volume
more correctly.
update_plex_state: Bring the plex up correctly when the last subdisk
comes up.
checksdstate: Update comments.
vpstate: Don't return an "up" state on a degraded, unattached plex.
start_object: Return a sensible error message when trying to revive a
subdisk whose drive is down. Previously it returned EBUSY.
Approved-by: jkh
data corruption. It's a wonder it worked at all.
Led-on-the-right-path-by: dillon
revive_block: Add treatment for RAID-4.
Add function parityrebuild, called by revive_block and parityops.
Approved-by: jkh
the tsleep call flags.
Submitted-by: Bernd Walter <ticso@cicely.de>
Remove references to vnode pointers, including debug output. Vinum
now talks directly to the device driver.
bre: Add case for RAID-4.
sdio: Don't try to write to a down drive. Set the sd state instead.
Approved-by: jkh
vn_open. This is necessary in order to be able to open drives before
the root file system is mounted. This also involves restructuring the
drive struct, which no longer contains a vnode pointer. Instead,
open_drive sets an open flag. It's a horrible kludge, and I'll gladly
borrow a Danish axe and hack it in little pieces when devfs comes.
read_drive, write_drive, drive_io_done: Replace with driveio. The
function names are now macros.
driveio: Fix horrible, embarrassing breakage which was the reason why
read_drive and write_drive existed in the first place.
Code-torn-to-shreds-by: dillon
format_config: Don't save config of objects in referenced state. They
get rebuilt automatically.
Change checks for striped or RAID-5 plexes to a macro 'isstriped',
which now also includes RAID-4.
Change checks for RAID-5 plexes to a macro 'isparity', which now also
includes RAID-4.
Replace the preprocessor variable names BDEV_MAJOR and CDEV_MAJOR with
VINUM_BDEV_MAJOR and VINUM_CDEV_MAJOR respectively.
vinum_scandisk: Don't free memory twice on error, once is enough.
Approved-by: jkh
to RAID-5. peter claims that it might be faster for sequential
reading, since the drive caches don't trip over the parity blocks. I
have seen no evidence to support this, but it's a trivial change.
Requested-by: peter
Change checks for striped or RAID-5 plexes to a macro 'isstriped',
which now also includes RAID-4.
Change checks for RAID-5 plexes to a macro 'isparity', which now also
includes RAID-4.
atoi(): Remove, nobody was talking to it.
give_sd_to_drive: If no space is available, make the subdisk down,
don't delete it.
Change the manner in which the subdisk count was maintained to avoid
cases where the count was not adjusted correctly.
config_drive: Check if we have subdisks referencing us, and add them
if so. This fixes problems which arose when a drive is replaced in a
running system.
config_sd: Add support for a keyword 'partition', whose meaning will
be revealed in the fullness of time.
Cosmetic: Shorten some console messages.
Approved-by: jkh
to SI_SUB_VINUM, thus making it possible for Vinum to access I/O
devices and start.
Replace the preprocessor variable names BDEV_MAJOR and CDEV_MAJOR with
VINUM_BDEV_MAJOR and VINUM_CDEV_MAJOR respectively.
Style fixes: replace NULL with 0 where appropriate.
Submitted-by: Charlie Root <root@sms-1.follo.net> (yup, that's all I
have to go on).
Approved-by: jkh
seriously- only attempt to logout a previously logged in fabric device.
Fix a longstanding bug for aborting overtime commands- handle halves
have always been reversed.
Clean up some error messages to indicate channel number.
Approved:jkh
Added receive code and support for Webgear encapsulation.
More debugging macros/functions.
conditionalised timeout for start/join network
conditonalised attribute/common memory hacks
identified tracking code with XXX_TRACK
sorted out initialistion of instance structure to some extent
finished docuementing the start/join sequence
The code doesn't compile (I'll do that in a minute), but functionally
it gets to receveing the interrupt from the start or join net command.
There is a lot of code to deal with the limitations of the PCCard memory
mapping code - I'm changing some of it hence the check in to preserve something
that worked.
Call intr_teardown on detach.
Always add non masterdevice from unit 2 upwards.
Update to the pccard code, at least some cards are now working,
more testing to follow.
