- Move intrhook stuff into kernel.h
- Remove all occurrences of #device <device.h>
- Add kernel.h were necessary (nowhere)
- delete device.h
This file contained the structures for cfdata (old style config) and is no
longer used. It was included by most drivers.
It confuses the remote debugger as the definition of 'struct device' in
device.h is found before the one in bus_private.h.
0x8024b04e) so that the cards description is used instead of overriding
it. While I'm here, add an ID for the SUP2080 and the SUP2030.
PR: kern/13983
Submitted by: Kurt D. Zeilenga <Kurt@OpenLDAP.Org> (SUP2030)
dfr (rest of change)
Reviewed by: dfr
Vendor ID SUP2480 (0x8024b04e), Serial Number 0x00001334
PnP Version 1.0, Vendor Version 0
Device Description: SupraExpress 56i Sp V.90
Reviewed by: dfr
kernel, but gcc provides a pessimal builtin for it.
Makefile.i386:
Added a variable (CONF_CFLAGS) for configuration-specific compiler flags.
LINT:
Use CONF_CFLAGS to inhibit use of gcc builtins.
Add debuging for all failure cases in aha_cmd().
Always check DATAIN_REG_READY even if we're ready to exit the
read loop.
The last fix allows the AHA-1640 MCA SCSI adapter to operate
correctly and likely fixes problems on a few other oddball
adapters. (I suspect my Dell Drive Array in 1540 mode needs this.)
Reviewed by: Warner Losh
apm_saver uses the apm_display() routine from the apm system to
"suspend" the "display" part of the machine.
This is beneficial for some laptops (or other machines with
non-traditional displays) that choke on the 'green' saver's
effect.
Another way of looking at this is that it's the same as a screen
saver that does an 'apm -d 0' to blank the display and an 'apm -d 1'
to bring it back. One probably ought to use these commands to make
sure the effect will be correct before using it unattended.
For unknown devices the output will now be
pci0: unknown card (vendor=0x109e, dev=0x0878) at 14.1 irq 19
instead of
pci0: unknown card DD^0878 (vendor=0x109e, dev=0x0878) at 14.1 irq 19
Before this change, the code used to take the PCI vendor id and translate it
into a three letter ASCII name.
For PnP devices, the vendor id _does_ map to a nice ASCII name
(eg Creative Labs PnP ID maps to "CTL", ESS PnP ID maps to "ESS")
But there is no such mapping for PCI devices, as can be seen by the
example above where the Brooktree PCI vendor ID maps to "DD^"
The PCI Special Interest Group confirmed they do not have any mappings
from vendor ID to ASCII.
and/or when using the card.
o Convert the driver to using bus_space. This allows alphas with
fxp's to boot, rather than panic'ing because rman_get_virtual()
doesn't really return a virtual address on alphas.
o Fix an alpha unaligned access error caused by some misfeature of
gcc/egcs: if link_addr & rbd_addr in the fxp_rfa struct are 32 bit
quantities, egcs will assume they are naturally aligned. So it will do
a ldl & some shifty/masky to twiddle 16 bit values in fxp_lwcopy().
However, if they are 16-bit aligned, the ldl will actually be done on
a 16-bit aligned value & we will panic with an unaligned access
error... Changing their definition to an array of chars seems to fix
this. I obtained this from NetBSD.
I've tested this on both i386 & alpha.
of parity check and rebuild operations. This enables us
to stop the operation and restart at a later time.
enum parityop: Trivial enum to decide what parityops() is going to do.
could stand.
Define the correct return lengths for a number of ioctls.
Add ioctls VINUM_CHECKPARITY and VINUM_RESETPARITY, still to be fully
implemented.
ourselves. This breaks a vicious circle which caused
vinum to dereference a null vp if device nodes were
missing.
Reported-by: Brad Chisholm <sasblc@unx.sas.com>
Alec Wolman <wolman@cs.washington.edu>
check_drive: Don't take a drive down if it's only referenced.
read_drive: Remove unused variable.
get_empty_volume: initialize plexes to -1 (not allocated)
remove_drive_entry:
Remove recurse parameter (there's nothing below a drive in the hierarchy).
Use remove_sd_entry to remove sds, don't do it ourselves.
Log errors, don't throw rude remarks.
remove_plex_entry:
Don't use plex->subdisks as a loop limit, it gets changed in the
loop. This caused some removals to only remove half the subdisks.
Change logging of some "impossible" situations.
remove_volume_entry:
Use remove_plex_entry to remove plexes, don't do it ourselves.
update_sd_config:
Use set_sd_state to do the work.
will have to mknod yourself for now.
* don't eat the first write()
* partial rvplayer fix- don't panic on unaligned writes unless our
feeder chain requires them for downconversion. a fuller fix is
on the way.
I386_BUS_SPACE_IO. Compiles now on the Alpha, but likely will not
work due to bus space address <-> virtual address mapping bogons that
work for i386 but not alpha.
work. Be more verbose when one cannot allocate IRQ, et al since this
is a common configuration problem. The cards have the IRQ soft wired
into their BIOS and do not try to do collision detection. This can
cause problems when this IRQ is the same as another card/device.
The PNP hasn't been tested. My PNP board is in a deployed system.
I'll sneak in testing of it sometime later. I've been able to mount
the 3.3R cdrom that arrived today and access files off it.
Submitted by: dfr
Leadtek Winfast 2000 cards.
No audio support yet, just the card make is reported.
Submitted by: Craig <crh@outpost.co.nz>
Submitted by: Peter Wemm <peter@netplex.com.au>
BUF_LOCKFREE a buffer prior to physically freeing it. While these
bugs did not cause a crash, they might in the future.
Added eof handling for unlabeled partitions.
Submitted by: Tor.Egge@fast.no
- Split out the prototypes, externs and struct decls from if_epreg.h into
if_epvar.h.
- Add support for MCA based Etherlink III (3c529) devices.
None of this code is used right now; the old if_ep driver is still
in place and used.
I will eventually get around to converting if_ep_isa.c to newbus once I've
had a talk with Peter and DFR about the DEVICE_IDENTIFY() method.
I have tested this code on my PS/2. It works. I would like EISA and ISA
testers since my example hardware hasn't arrived yet.
Add:
dev/ep/if_ep.c optional ep
dev/ep/if_ep_isa.c optional ep isa
dev/ep/if_ep_eisa.c optional ep eisa
dev/ep/if_ep_mca.c optional ep mca
dev/ep/if_ep_pccard.c optional ep card
to sys/conf/files
Remove:
i386/eisa/3c5x9.c optional ep
i386/isa/if_ep.c optional ep
from sys/i386/conf/files.i386
PCCARD testers wanted!
I will switch off and cvs rm the old driver in favor of this copy once
I've had positive feedback or have the hardware to verify that it works.
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
fields in struct cdevsw:
d_stop moved to struct tty.
d_reset already unused.
d_devtotty linkage now provided by dev_t->si_tty.
These fields will be removed from struct cdevsw together with
d_params and d_maxio Real Soon Now.
The changes in this patch consist of:
initialize dev->si_tty in *_open()
initialize tty->t_stop
remove devtotty functions
rename ttpoll to ttypoll
a few adjustments to these changes in the generic code
a bump of __FreeBSD_version
add a couple of FreeBSD tags
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
for you to be told there was an error [during verbose boot].
I poked him for the fix, he poked me to get it committed.
Submitted by: Jason Young <doogie@anet-stl.com>
Enhance MIRROR code. Add a few more sanity checks and implement
a zone-based disk selector to make use of both disks when reading.
Also implement a read fail-over. If a read error occurs on one
disk, the I/O is retried on the other.
NOTE: CCD's mirroring support cannot deal with write errors properly
in regards to recovery, meaning that 'old' data under a write error may
be read non-deterministically if you reboot after a write error, and CCD
certainly cannot deal with a disk changeout. And it still can't. Use
vinum if you are really serious about mirroring. CCD basically just
implements a poor-man's mirror.
sum the total amount of I/O issued to determine when all the I/O
has completed. This fails when the EOF boundry occurs in the middle
of an I/O. Using cbp->cb_buf.b_bufsize works better.
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
The lun is not incremented in the ata-disk driver when ATA_STATIC_ID
is not defined, thanks to Kenneth Wayne Culver <culverk@wam.umd.edu>
for finding that one.
PHK pointed at the & problem in atapi-cd in devstat_end_transaction_buf.
Too little sleep I guess...
Phase 1) move the driver
Phase 2)
Phase 3) Profit, by splitting the driver into smaller files like
bktr_tuner, bktr_card, bktr_audio, bktr_<osname>
making it easier to maintain and understand.
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."
This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
It been awhile since the last major update, as a benefit there
are some cool things in this one (and new bugs probably :) )...
The ATA driver has grown "real" timeout support for all devices.
This means that it should be possible to get in contact with
(especially) lost ATAPI devices. It also means that the ATA
driver is now usable on notebooks as it will DTRT on resume.
An experimental hack at utilizing the Promise66's at UDMA66 is
in there, but I cant test it. If someone feels like sending
me one, give me a ping.
The ATAPI DMA enableling scheme has been changed, also better DMA
support for the Aladdin chipset has been implemented for ATAPI
devices. Note that the Aladdin apparently only can do DMA reads
on ATAPI devices, and the Promise cant do ATAPI DMA at all.
I have seen problems on some ATAPI devices that should be able
to run in DMA mode, so if you encounter problems with hanging
atapi devices during the probe, or during access, disable DMA
in atapi-all.c, and let me know. It might be nessesary to do this
via a "white list" for known good devices...
The ATAPI CDROM driver can now use eject/close without hanging and
the bug that caused reading beyond the end of a CD has been fixed.
Media change is also handled proberly. DVD drives are identified
and are usable as CDROM devices at least, I dont have the HW to
test this further, see above :).
The ATAPI tape driver has gotten some support for using the DSC
method for not blocking the IDE channel during read/write when
the device has full buffers. It knows about the OnStream DI-30
device, support is not completed yet, but it can function as a
primitive backup medium, without filemarks, and without bad media
handeling. This is because the OnStream device doesn't handle this
(like everybody else) in HW. It also now supports getting/setting
the record position on devices that supports it.
Some rather major cleanups and rearrangements as well (cvs -b diff
is your freind). I'm closing in on declaring this for beta code,
most of the infrastruture is in place by now.
As usual USE AT YOUR OWN RISK!!, this is still alpha level code.
This driver can hose your disk real bad if anything goes wrong, but
now you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
This whole idea isn't going to work until somebody makes the bus/kld
code smarter. The idea here is to change the module's internal name
from "foo" to "if_foo" so that ifconfig can tell a network driver from
a non-network one. However doing this doesn't work correctly no matter
how you slice it. For everything to work, you have to change the name
in both the driver_t struct and the DRIVER_MODULE() declaration. The
problems are:
- If you change the name in both places, then the kernel thinks that
the device's name is now "if_foo", so you get things like:
if_foo0: <FOO ethernet> irq foo at device foo on pcifoo
if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo
This is bogus. Now the device name doesn't agree with the logical
interface name. There's no reason for this, and it violates the
principle of least astonishment.
- If you leave the name in the driver_t struct as "foo" and only
change the names in the DRIVER_MODULE() declaration to "if_foo" then
attaching drivers to child devices doesn't work because the names don't
agree. This breaks miibus: drivers that need to have miibuses and PHY
drivers attached never get them.
In other words: damned if you do, damned if you don't.
This needs to be thought through some more. Since the drivers that
use miibus are broken, I have to change these all back in order to
make them work again. Yes this will stop ifconfig from being able
to demand load driver modules. On the whole, I'd rather have that
than having the drivers not work at all.
usually cleared by a successful selection, but there is no guarantee
that a future successful selection will ever occur (e.g. empty bus).
The driver never looks at SELINGO, but the busy LED does, so this
change has the cosmetic effect of fixing the rare instance where the
busy LED was left on, confusing the user.
aic7xxx parts. This problem could result in data corruption
during periods of my PCI bus load by busmasters other than the
aic7xxx.
Many thanks to Andrew Gallatin <gallatin@cs.duke.edu> for characterizing
the symptoms of this problem and testing this fix.
adjust the bp->b_bcount the same way for unlabeled VN access as dscheck
does for labeled access.
We also increase the block size to at least 8K for efficiency.
Reviewed by: Tor.Egge@fast.no
- Remove sc_get_scr_stat(). It's not necessary anymore.
- Call ttymalloc() to allocate the struct tty for each vty, rather than
statically declaring an array of struct tty. We still need a statically
allocated struct tty for the first vty which is used for the kernel
console I/O, though.
- Likewise, call ttymalloc() for /dev/sysmouse and /dev/consolectl.
- Delete unnecessary test on the pointer struct tty *tp in some functions.
- Delete unused code in scmouse.c.
WARNING: this change requires you to recompile screen savers!
1) Reworked the probe routine
2) Addition of the 574B's product ID.
3) Added useful info when booting verbosely.
Submitted by: Jason Young <doogie@anet-stl.com>
Bug fix: xmradio nolonger experiences a 6Mhz offset after running FXTV
New feature: Automatic Tuner selection for AVerMedia cards with
configuration EEPROMs on (ie the Bt878 based cards)
length for mini receive ring. The max length was MHLEN, however the mbufs
are actually shortened to MHLEN - ETHER_ALIGN to force payload alignment.
PR: 13793
size != 512 that are configured without a label. The bug should only
have effected swap-backed VN mounts without a label.
Add several major features to VN. In the kernel we add a swap
pre-reservation capability, which can be used to guarentee seek
consistency for swap-backed VN nodes. This also incidently allows
a swap-backed VN filesystem to be recovered after a crash in some
cases (if the same swap blocks happen to be reserved).
We also add a number of new options to vnconfig which do the work
of pre-zeroing or creating/truncating/extending a file which greatly
simplifies using VN in a file-backed configuration.
Add FreeBSD CVS label to sys/sys/vnioctl.h, as well as a new ioctl
flag for the swap pre-reservation feature.
Reviewed by: Alan Cox <alc@cs.rice.edu>, David Greenman <dg@root.com>
warnings caused by the arg having the wrong type (not const enough).
The arg was also wrong (a full name instead of a short one) for calls
from from subr_diskmbr.c and pc98/diskslice_machdep.c.
rewrite the pccard attachment case. This is a work in progress, but
doesn't break the isa case.
I left the #if 0...#endif around the pccard stuff, at Peter's request,
so that normal users don't shoot themselves in the foot.
While I was here:
o Indent a comment to the right location
o Spell Unknown with a final 'n'.
Reviewed by: peter
I have an 82559 card with the same id as the other 8255[78] chips, but
that was made with a date code of 0699 (June 99). The submitter shows
this working with the probe etc, but doesn't actually say it works as
on the ethernet. :-) Assuming it does, this is a RELENG_3 merge candidate.
Submitted by: Steven E Lumos <slumos@sam.ISRI.UNLV.EDU>
this PHY and the Davicom DM9101 have exactly the same register definitions.
One of them is probably a clone of the other. I'm not sure which.
This is needed for the Davicom DM9102 10/100 PCI ethernet driver which
will be committed shortly.
Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
a quick think and discussion among various people some form of some of
these changes will probably be recommitted.
The reversion requested was requested by dg while discussions proceed.
PHK has indicated that he can live with this, and it has been agreed
that some form of some of these changes may return shortly after further
discussion.
MCA SCSI adapters.
bt_mca.c is going to live in sys/dev/buslogic instead of sys/dev/mca
as per a conversation with Peter, Doug and Mike.
Thanks to Andy Farkas <andyf@speednet.com.au> for being such a good
sport and doing all the testing for me (as I don't actually own one
of these cards. Yet.)
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
the new PnP code. Since the bulk of the driver changes are not being
committed at this time, it will not affect the driver. The code is being
committed early to allow others synchronise changes.
new system is integrated with the ISA bus code more cleanly and allows
the future addition of more enumerators such as PnPBIOS and ACPI.
This commit also enables the new pcm driver since it is somewhat tied to
the new PnP code.
Fix a bug where video capture locks up on channel changes.
Many thanks to Juha for solving this.
Submitted by: Juha Nurmela <Juha.Nurmela@quicknet.inet.fi>
New Features:
Greatly improved VBI capture support. (mainly for the AleVT port)
Supports select() on /dev/vbi
Improved RISC program for RGB+VBI capture to capture both evenodd
VBI data even when only capturing even only (or odd only) video
Based on code from Juha Nurmela <Juha.Nurmela@quicknet.inet.fi>
Support for Hauppauge 627 and Temic 4006
Submitted by: Maurice Castro <maurice@atum.castro.aus.net>
Bug Fix:
Fix bug in AverMedia card detection.
Break out the detection logic for the aic7855 and properly report
these chips as 7855s instead of 7850s.
The 2940AU_CN is an aic7860 based card, not aic7860.
Not setting CACHETHEN turned out to be a bad idea. It can cause
spurious corruption under heavy PCI load with multiple masters.
the highly non-recommended option ALLOW_BDEV_ACCESS is used.
(bdev access is evil because you don't get write errors reported.)
Kill si_bsize_best before it kills Matt :-)
Use the specfs routines rather having cloned copies in devfs.
the highly non-recommended option ALLOW_BDEV_ACCESS is used.
(bdev access is evil because you don't get write errors reported.)
Kill si_bsize_best.
Use the specfs routines rather having cloned copies in devfs.
ones were made by Lucent). The Broadcom chip also appears to use an
internal PHY made by Broadcom which uses the Broadcom OUI. This is different
from previous ASICs which always returned 0 in the PHY ID registers.
To account for this, I added the necessary ID values for the Broadcom
PHY so that it can be detected and attached using the 3Com PHY driver
instead of defaulting to the generic one.
This fixes, at least, panics in ncr_attach() on i386's with about 5MB
of memory. The restriction was a hack to leave some low memory for ISA
DMA, but on i386's we now allocate pages from the top down, so all the
restriction did was cause our allocations to fail when there is no free
memory above 1MB.
some swapper problems analogous to those experienced with ccd.
This fix is a kludge: since we currently don't track the "sector size"
in a volume label, we guess a worst case (4 kB, as used by vnode
devices). If the concept of sector size is here to stay, I'll make
some changes to track the "sector size" of a volume. This will
probably be the maximum of the sector sizes of all component drives,
but things could get ugly if we start allowing non-standard sector
sizes such as 524 bytes.
Unkludged-version-submitted-by: phk
ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is
a port of the NetBSD driver with various hacks. The ML driver is necessary
to support the Olicom OC-2326 ThunderLAN-based NIC.
Also regenerated miidevs.h to pick up the proper 'obtained from'
revision string.
lockrange: correctly expand rangelock struct, including expanding a
null struct. Previously lockrange would attempt to lock a
NULL pointer under these circumstances.
Reported-by: Ian Freislich <iang@uunet.co.za>
initialized subdisks.
Tidy up some comments.
Eliminate sddownstate(); it wasn't being used any more. Return
REQUEST_DOWN instead.
Add setstate_by_force() to implement the VINUM_SETSTATE_FORCE ioctl
for diddling individual object states. This is a repair tool which
can also be used for panicing the system. Use with utmost care if at
all.
avoids a race condition where multiple RAID-5 subdisks are being
revived at the same time. The locks should also prevent conflicts
with user requests on concatenated and striped plexes, but this needs
more work.
Tidy up some comments.
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
instead, use generic entry points for all drivers.
- Eliminate bogus makedev().
- Eliminate softc in the lower drivers, as it is no longer necessary.
Submitted (95%) by: phk
MII-compliant PHY drivers. Many 10/100 ethernet NICs available today
either use an MII transceiver or have built-in transceivers that can
be programmed using an MII interface. It makes sense then to separate
this support out into common code instead of duplicating it in all
of the NIC drivers. The mii code also handles all of the media
detection, selection and reporting via the ifmedia interface.
This is basically the same code from NetBSD's /sys/dev/mii, except
it's been adapted to FreeBSD's bus architecture. The advantage to this
is that it automatically allows everything to be turned into a
loadable module. There are some common functions for use in drivers
once an miibus has been attached (mii_mediachg(), mii_pollstat(),
mii_tick()) as well as individual PHY drivers. There is also a
generic driver for all PHYs that aren't handled by a specific driver.
It's possible to do this because all 10/100 PHYs implement the same
general register set in addition to their vendor-specific register
sets, so for the most part you can use one driver for pretty much
any PHY. There are a couple of oddball exceptions though, hence
the need to have specific drivers.
There are two layers: the generic "miibus" layer and the PHY driver
layer. The drivers are child devices of "miibus" and the "miibus" is
a child of a given NIC driver. The "miibus" code and the PHY drivers
can actually be compiled and kldoaded as completely separate modules
or compiled together into one module. For the moment I'm using the
latter approach since the code is relatively small.
Currently there are only three PHY drivers here: the generic driver,
the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding
others later as I convert various NIC drivers to use this code.
I realize that I'm cvs adding this stuff instead of importing it
onto a separate vendor branch, but in my opinion the import approach
doesn't really offer any significant advantage: I'm going to be
maintaining this stuff and writing my own PHY drivers one way or
the other.
events, in order to pave the way for removing a number of the ad-hoc
implementations currently in use.
Retire the at_shutdown family of functions and replace them with
new event handler lists.
Rework kern_shutdown.c to take greater advantage of the use of event
handlers.
Reviewed by: green
Notice that 'unit' wasn't defined once I changed the parameters of the func.
These things make me feel like wading in with a flamethrowr or something.
Too much cruft!
</rant>
if_init_f_t is passed void * containing the address of ifp->if_softc
not the unit number.
Someone tell me if these things don't work as I don't have the hardware
needed to test them. (thats a first.)
I'll get if_ze and if_zp later.
Pointed out by: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>
to achieve a delay is pretty mean.
Andrew reports:
"The tulip_delay_300ns() is, well, bloody stupid on machines with a
heavily loaded PCI bus. It tries to do a delay by assuming PCI reads
will take a certain amount of time & issues a large amount of
(expensive, 5% CPU when your PCI bus is heavily loaded) pci reads.
Locally, we've replaced the calls to tulip_delay_300ns(sc) in the EMIT
macros with a simple DELAY(1) and not seen any problems. Plus we've
gained about 50Mb/sec throughput on our gigabit network cards because
of the added PCI bus bandwidth available."
Also, I do not understand why, but this change appears to stop the
Transmit Fifo underrun on one of my systems (but not the Alpha PC164SX).
This shouldn't make that much of a difference since the mii bus isn't
touched all that often, but perhaps when it does get accessed and hence
hammers the register, it was causing the chip to get upset.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu>
about a dev_t.
printf("%x", dev) now becomes printf("%s", devtoname(dev)) because
printing actual information about the device is much more useful then
printing a pointer to an address that would never help the developer debug.
Submitted by: phk, bde
messages, abort messages, and abort tag messages.
Fix a bug in how default transfer negotiations are handled if the
user had disabled initial bus resets.
Support multi-targetid on the aic7895C.
format_config: code preening.
vinum_scandisk: If we find a partition in the first pass over a drive,
note the fact so we don't grab the compatibility partition as well.
Submitted-by: peter
the aic7890/91/96/97 cards. This could cause the system to go into
a long retry/recovery loop during probe.
Fix the alignment argument to bus_dma_tag_create().
Don't set the CACHETHEN bit in dscommand0 for Ultra2 controllers
until we know more about its behavior. The description for this
bit makes it sound like it could cause problems with certain
PCI chipsets.
goes into initialized state, not 'up'. This makes it easier to ensure
consistency in multi-plex volumes.
update_plex_state: redo transitions from empty and initialized
subdisks to up or reviving, depending on the number of plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
Don't return "can't do it" when the user requests a state change to
the current state. This previously caused silly messages like "Can't
start <foo>: invalid argument", when in fact <foo> was already
started.
set_plex_state: don't set state for non-existent plexes.
update_plex_status: as long as we have initializing subdisks, we're
initializing.
Move the declaration of freerq() to request.h.
logrq: add support for lock events.
vinumstart: solve a problem where removing a plex from an active
volume could cause attempts to access non-existent plexes.
launch_requests: don't set a request group active until we're sure we
can launch it. This caused some hangs under unusual
circumstances.
bre: don't set XFR_BAD_SUBDISK if we're not going to use it.
build_read_request: correct recovery, which caused some hangs under
(other) unusual circumstances.
build_rq_buffer: don't set bp->b_dev if we don't have a dev.
sdio: clean up, remove obsolete code.
deallocrqg: unlock any locks the rqg may have.
bre5:
Shorten some lines.
Desired-by: bde
If we're reading from a short plex, return EOF indication.
Always lock the stripe before starting a transfer. Hopefully the
current version will solve some data integrity problems that have
been reported with degraded RAID-5 plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
solve some data integrity problems that have been reported with
degraded RAID-5 plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
Tidy other comments.
open_drive: don't call set_drive_state if we decide to take it down.
This could help avoid some race conditions with the daemon.
init_drive: don't set the drive down, we'll let close_locked_drive do
that.
close_locked_drive: set drive state to down without calling
set_drive_state. This could help avoid some race conditions with the
daemon.
driveio: remove the function, it wasn't being used.
get_volume_label: remove volume dependencies so that we can return a
label for plexes and subdisks as well. What a kludge.
Remove declarations for freerq and free_rqg.
Remove DEBUG_RESID code.
freerq: check whether the request is holding a lock, free if so.
free_rqg: remove. It wasn't being used any more.
Change the Debugger calls to panics.
checkdiskconfig(): remove. It didn't make any sense to complain about
kernel keywords in user config files; it just made it more difficult
to convert. Now we ignore kernel keywords if we're not in kernel
mode.
get_empty_sd: initialize sectors.
free_drive: don't close if we don't have a vp. Maybe this will help
fix the problem that peter had, but I wouldn't count on it.
config_plex: If the plex is RAID-5, give it a rangelock structure.
start_config: Reset current drive, plex and volume so that a new
'create' command doesn't get long-dead defaults.
struct rqelement, enum rqinfo_type, struct rqinfo, union rqinfou: add
lock requests.
Add declarations for freerq and unlockrange. Since they include
request structures, they can't go in vinumext.h
a module. Also modified the code to work on FreeBSD/alpha and added
device vr0 to the alpha GENERIC config.
While I was in the neighborhood, I noticed that I was still using
#define NFPX 1 in all of the Makefiles that I'd copied from the fxp
module. I don't really use #define Nfoo X so it didn't matter, but
I decided to customize this correctly anyway.
- %q -> %ll.
Fixed nearby errors not reported by gcc -Wformat on i386's:
- don't assume that the promotion of [u_]int64_t is [u_]quad_t.
- don't use signed formats for unsigned args.
Add Cybernet copyright.
OK'd-by: Chuck Jacobus <chuck@cybernet.com>
update_plex_state:
If any subdisk in the plex is initializing, set the plex to
initializing state. This gets rid of the ugly corrupt/degraded/up
transitions which previously occurred.
Desired-by: Steve Taylor <staylor@cybernet.com>
sddownstate:
Add new function, used by checksdstate.
checksdstate:
Let sddownstate decide what status to return.
Add Cybernet copyright.
OK'd-by: Chuck Jacobus <chuck@cybernet.com>
logrq: save device major and minor numbers to compensate for lost
dev_t.
launch_requests: Don't issue requests which are marked
XFR_BAD_SUBDISK. This may make things easier in bre().
bre:
Rearrange.
- Change some comments
- Recognize holes in plex structure. Formerly this could lead to
incorrect write to the plex. Return REQUEST_DEGRADED on a read
request, but carry on to the bitter end on a write request, and
mark the requests for the inaccessible subdisks with
XFR_BAD_SUBDISK.
- return REQUEST_EOF if the requested transfer goes beyond the end
of the plex. This is not an error, since other plexes may go
further into the volume address space.
build_read_request:
Handle REQUEST_DEGRADED returned from bre().
sdio:
Lock buffer before issuing the requests.
will only accept partitions of type 'vinum'.
format_config: Use the new %q format option in kvprintf, thus getting
rid of some of the filthiest code I've written in a long time. Also
remove the lltoa() function.
With-great-thanks-to: peter
format_config: Accept the fact that a subdisk might not be attached to
a plex, and save the config correctly.
vinum_scandisk: Scan all slices on a drive with a Microsoft partition
table. Only look at the compatibility slice if nothing was found in
the Microsoft slices.
This change removes a frequently employed method of shooting
yourself in the foot: people would decide that the Vinum drives
belonged on their own slice, and they wouldn't be able to start the
subsystem after a reboot. Documentation updates to follow.
initialize subdisks. Probably the plex-related subdisk type will die
a death.
vinumconfig.c:
Accept (and ignore) kernel state information in userland config
files. This saves a lot of error recovery and also makes it possible
to use the output of printconfig to create new configuration.
Remove checkdiskconfig(). It wasn't needed any more.
Start adding support for hot spare drives. You can't put anything on
them (yet).
Change message formats from %lld to %qd.
get_empty_sd: Initialize size to -1. Previously this was done in
config_subdisk, which is the wrong place.
start_config: set current drive, plex and volume to -1, thus stopping
update configurations from taking their defaults from old configs.
now used in f_ops in place of NULL, and modifications to the files
are more carefully ordered. f_ops should also be set to &badfileops
upon "close" of a file.
This does not fix other problems mentioned in this PR than the first
one.
PR: 11629
Reviewed by: peter
eisa_add_intr() which now takes an additional arguement (one of
EISA_TRIGGER_LEVEL or EISA_TRIGGER_EDGE).
The flag RR_SHAREABLE has no effect when passed to
bus_alloc_resource(dev, SYS_RES_IRQ, ...) in an EISA device context as
the eisa_alloc_resource() call (bus_alloc_resource method) now deals
with this flag directly, depending on the device ivars.
This change does nothing more than move all the 'shared = inb(foo + iobsse)'
nonesense to the device probe methods rather than the device attach.
Also, print out 'edge' or 'level' in the IRQ announcement message.
Reviewed by: dfr
- device_print_child() either lets the BUS_PRINT_CHILD
method produce the entire device announcement message or
it prints "foo0: not found\n"
Alter sys/kern/subr_bus.c:bus_generic_print_child() to take on
the previous behavior of device_print_child() (printing the
"foo0: <FooDevice 1.1>" bit of the announce message.)
Provide bus_print_child_header() and bus_print_child_footer()
to actually print the output for bus_generic_print_child().
These functions should be used whenever possible (unless you can
just use bus_generic_print_child())
The BUS_PRINT_CHILD method now returns int instead of void.
Modify everything else that defines or uses a BUS_PRINT_CHILD
method to comply with the above changes.
- Devices are 'on' a bus, not 'at' it.
- If a custom BUS_PRINT_CHILD method does the same thing
as bus_generic_print_child(), use bus_generic_print_child()
- Use device_get_nameunit() instead of both
device_get_name() and device_get_unit()
- All BUS_PRINT_CHILD methods return the number of
characters output.
Reviewed by: dfr, peter
equivalent to SYS_RES_MEMORY for x86 but for alpha, the rman_get_virtual()
address of the resource is initialised to point into either dense-mapped
or bwx-mapped space respectively, allowing direct memory pointers to be
used to device memory.
Reviewed by: Andrew Gallatin <gallatin@cs.duke.edu>
This function is called for each device for which no driver
was found.
Output is similar to the eisa_probe_nomatch() function but with the
added benefit of displaying the assigned IRQ (since PCI gives us
this information up front.)
Output is like so:
pci0: unknown card CPQ0508 (vendor=0x0e11, dev=0x0508) at 11.0 irq 9
pci0: unknown card DFZ0508 (vendor=0x10da, dev=0x0508) at 11.0 irq 9
pci0: unknown card DBL0508 (vendor=0x104c, dev=0x0508) at 11.0 irq 9
pci0: unknown card DDM0011 (vendor=0x108d, dev=0x0011) at 11.0 irq 9
I'm not happy with the 3 lines of macro cruft that got added but
I consider it a temporary annoyance as those bits will be moved to
some place where PCI, EISA and ISAPNP code will be able to use them.
(Not surprisingly, this message is longer than the code in question.)
Reviewed by: peter, dfr
a PCI memory mapped region, rman_get_bushandle() returns what happens
to be a kernel virtual address pointing to the base of the PCI shared
memory window. However this is not the behavior on all platforms:
the only thing you should do with the bushandle is pass it to the
bus_spare_read()/bus_space_write() routines. If you actually do want
the kernel virtual address of the base of the PCI memory window, you
need to use rman_get_virtual().
The problem is that at the moment, rman_get_virtual() returns a physical
address, which is bad. In order to get the kernel virtual address we
need, we have to play with it a little.
Presumeably this behavior will be changed, but in the meantime the
Tigon driver won't work. So for the moment, I'm adding a kludge to
make things happy on the alpha: the correct kernel virtual address
is calculated from the value returned by rman_get_virtual(). This
should be removed once rman_get_virtual() starts doing the right
thing.
This should make the Tigon actuall work on the alpha now.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
critical mbuf fields to sane values. Simplify the use of ETHER_ALIGN to
enforce payload alignment, and turn it on on the x86 as well as alpha
since it helps with NFS which wants the payload to be longword aligned
even though the hardware doesn't require it.
This fixes a problem with the ti driver causing an unaligned access trap
on the Alpha due to m_adj() sometimes not setting the alignment correctly
because of incomplete mbuf initialization.
the driver_t declaration should be "skc" not "sk". Technically, "skc"
is the parent PCI device (the SysKonnect GEnesis controller) and "sk0"
and "sk1" are the network interfaces that get attached to it.
the device numbers are now minor number only, so that we can still
compare them after dev_t has turned into a blob.
Broken-by: dev_t changes
Reported-by: Vallo Kallaste <vallo@matti.ee>
"Niels Chr. Bank-Pedersen" <ncbp@bank-pedersen.dk>
by removing a floppy that as being operated on.
The spagghetti is hardly understandable at all anymore, so i can't
100 % ascertain this is really the Right Thing to do, maybe our new
floppy driver maintainer, Jesus Monroy Jr can do this. :-))
The structure is the right length, but some of the members (notably
wi_q_info) were off a bit. This causes the received signal strength
values to appear bogus.
vnodes referencing this device.
Details:
cdevsw->d_parms has been removed, the specinfo is available
now (== dev_t) and the driver should modify it directly
when applicable, and the only driver doing so, does so:
vn.c. I am not sure the logic in checking for "<" was right
before, and it looks even less so now.
An intial pool of 50 struct specinfo are depleted during
early boot, after that malloc had better work. It is
likely that fewer than 50 would do.
Hashing is done from udev_t to dev_t with a prime number
remainder hash, experiments show no better hash available
for decent cost (MD5 is only marginally better) The prime
number used should not be close to a power of two, we use
83 for now.
Add new checkalias2() to get around the loss of info from
dev2udev() in bdevvp();
The aliased vnodes are hung on a list straight of the dev_t,
and speclisth[SPECSZ] is unused. The sharing of struct
specinfo means that the v_specnext moves into the vnode
which grows by 4 bytes.
Don't use a VBLK dev_t which doesn't make sense in MFS, now
we hang a dummy cdevsw on B/Cmaj 253 so that things look sane.
Storage overhead from all of this is O(50k).
Bump __FreeBSD_version to 400009
The next step will add the stuff needed so device-drivers can start to
hang things from struct specinfo
interrupts that were scheduled. Testing shows it didn't really do very much
and it makes the code a little more complicated (which is never a good thing).
Also fix the rambuffer offset initialization for the 512K/64K SRAM case
(512K total using 64K chips). It should be 0. The only case with a
non-standard rambuffer offset address is 1024K/64K according to the
SysKonnect manual. (My card has the 1024/64 configuration and I don't know
which card uses the 512/64 configuration, if any, so I'm not sure that
this was really a problem for anyone.)
Change number of VBI lines from 16 to 12 for NTSC formats.
Juha.Nurmela@quicknet.inet.fi found/fixed bug in VBI_SLEEP.
New features
MSP3430G DBX initialisation from Matt Brown <matt@dqc.org>
STB Bt878 card identification.
Hauppauge Model Number identification.
Changes to probeCard() for better eeprom identification.
Experimental TDA9850 initialisation code, from Linux bttv.
Cross Platform Changes
The driver has been reorgainsed based ideas from Brad Parker's port to Linux
to seperate OS Dependant and Independant sections.
I have backends for FreeBSD 2.2.x/3.x and 4.x newbus, BSDI, OpenBSD and NetBSD.
This commit has FreeBSD 2.2.8/2.2-stable/3.x and FreeBSD 4.x newbus backends.
Some code submitted by: Juha.Nurmela@quicknet.inet.fi
Matt Brown <matt@dqc.org>
Brad Parker <brad@parker.boston.ma.us>
Some code obtained from: Linux bttv driver
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
- Correctly observe the variable `extra_history_size' when changing
the size of history (scroll back) buffer.
- Added sc_free_history_buffer().
Pointed out by: des
in ti_rxeof() instead. This doesn't really seem to provide much in the
way of a performance boost, and I'm pretty sure it can cause mbuf leakage
in some extreme cases.
frames (or just insane received packet lengths generated due to errors
reading from the NIC's internal buffers). Anything too large to fit
safely into an mbuf cluster buffer is discarded and an error logged.
I have not observed this problem with my own cards, but on user has
reported it and adding the sanity test seems reasonable in any case.
Problem noted and patch provided by: Per Andersson <per@cdg.chalmers.se>
isp_io_map, isp_no_fwload, isp_fwload, isp_no_nvram, isp_fcduplex
which are all bitmaps of isp instances that should or shouldn't
map memory space, I/O space, not load f/w, load f/w, ignore nvram,
not ignore nvarm, set full duplex mode. Also have an isp_seed value
that we can use to generate a pseudo seed for a synthetic WWN.
Other minor cosmetic cleanup. Add in support for the Qlogic ISP
2200. Very important change where we actually check now to see
whether we were successful in mapping request and response queues
(and fibre channel scratch space).
not having SCSI_ISP_SCCLUN config defined if we don't have f/w for
the 2200- it's resident firmware uses SCCLUN (65535 luns)). Change
the way the default LoopID is gathered (it's now a platform specific
define so that some attempt at a synthetic WWN can be made in case
NVRAM isn't readable).
Change initialization of options a bit- don't use ADISC. Set
FullDuplex mode if config options tells us to do so. Do not use
FULL_LOGIN after LIP- it's the right thing to do but it causes too
much loop disruption (Loop Resets). Sanity check some default
values. Redo construction of port and node WWNs based upon what we
have- if we have 2 in the top nibble, we can have distinct port
and node WWNs. Clean up some SCCLUN related code that we obviously
had never compiled (:-(). Audit commands coming int ispscsicmd and
don't throw commands at Fibre devices that do not have Class 3
service parameters TARGET ROLE defined.
Clean up f/w initialization a bit. Add Fabric support (or at least
the first blush of it). Whew - way too much to describe here.
Basically, after a LIP, hang out until we see a Loop Up or a Port
DataBase Change async event, then see if we're on a Fabric
(GET_PORT_NAME of FL_PORT_ID). If we are, try and scan the fabric
controller for fabric devices using the GetAllNext SNS subcommand.
As we find devices, announce them to the outer layer. Try and do
some guard code for broken (Brocade) SNS servers (that get stuck
in loops- gotta maybe do this a different way using the GP_ID3 cmd
instead). Then do a scan of the lower (local loop) ids using a
GET_PORT_NAME to see if the f/w has logged into anything at that
loop id. If so, then do a GET_PORT_DATABASE command. Do this scan
into a local database. At this point we can say the loop is 'Ready'.
After this, we merge our local loop port database with our stored
port database- in a as yet to be really fully exercised fashion we
try and follow the logic of something having moved around. The
first time we see something at a Loop ID, we fix it, for the purpose
of this system instance, at that Loop ID. If things shift around
so it ends up somewhere else, we still keep it at this Loop ID (our
'Target') but use the new (moved) Loop ID when we actually throw
commands at it. Check for insane cases of different Loop IDs both
claiming to have the same WWN- if that happens, invalidate both.
Notify the outer layer of devices that have arrived and devices
that have gone away. *Finally*, when this is done, search the
softc's database of Fabric devices and perform logout/login actions.
The Qlogic f/w maintains logout/login for all local loop devices.
We have to maintain logout/login for fabric devices- total PITA.
Expect to see this area undergo more change over time.
Change some fcp parameter structures such that we can get the portid
(24 bit value), get both node and port WWN, know whether we're on a fabric
or not, note whether we've ever seen the loop up, and note the current
state of the loop.
Replace the isp_pdb_t structure in fcparams with a reduced cost structure
that maintains a static relationship to 'Target', but can have the actual
loop ID used change (in case, post LIP, we discover things have moved
around). This also retains portid and node/port WWNs. This array gets
larger if we have fabric support compiled in.
Note special loop IDs that are invariate for this device- FL_PORT_ID
(0x7e) which tells us if there's a fabric controller present, FC_PORT_ID
and FC_SNS_ID (fabric controller port and fabric SNS server port). We don't
use the latter two for anything. IDs above FC_SNS_ID up through 255 are
available for mapping fabric devices to 'target' ids.
Add in a config define to set FC full duplex mode. Add in a define to
recognize the Qlogic 2200 boards. Add comments about ISPCTL commands.
Add and change some ISPASYNC enumes.
compiles cleanly on the Alpha. (On the alpha, the port type is an int,
not a short).
Cast a couple of pointers to ints via 'uintptr_t' rather than 'unsigned
int' since uintptr_t is long (64 bit) on Alpha, as are pointers.
Correct race condition between caller and daemon.
Tripped-over-by: Zach Heilig <zach@uffdaonline.net>
Bernd Walter <ticso@cicely.de>
Niels Chr. Bank-Pedersen <ncbp@bank-pedersen.dk>
lockmgr locks. This commit should be functionally equivalent to the old
semantics. That is, all buffer locking is done with LK_EXCLUSIVE
requests. Changes to take advantage of LK_SHARED and LK_RECURSIVE will
be done in future commits.
The atapi subsystem has gotten better error handeling and timeouts,
it also tries a REQUEST SENSE command when devices returns errors,
to give a little more info as to what went wrong. It might be a
little verbose for now, but I'm interested in as much feedback on
errors as possible, especially timeouts, as I'm a bit in doubt if
I've chosen resonable default values everywhere.
The disk driver has been changed a bit to prepare for tagged queing,
which is next on my list.
The disk driver has grown a dump routine, I got one implementation
from Darrell Anderson <anderson@cs.duke.edu> which also did
partial dumps (usefull on big memory machines) I left out the
partial stuff for now, and changed the rest alot to fit into the new
ad_request framework.
Some minor cleanups and rearrangements as well.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, again you have been warned :)
Notebook owners should be carefull that their machines dont suspend
as this might cause trouble...
But please tell me how it works for you!
Enjoy!
-Søren
and insertion should affect the line the cursor is on only.
This change should have been committed together with syscons.c rev 1.308.
(I forgot to do so, when I committed syscons.c :-(
Pointed out by: sos
If the drive goes down, queue a close to the daemon. In many cases
this function gets called in process context, so it could do it
directly, but it's more trouble finding out where we came from than
getting the daemon to do it.
Don't bzero the buffer structure, it's been done already by
allocrqg.
sdio:
Build up a correct buffer header, don't steal linkages from system
buffer headers.
Noticed-by: mckusick
* Conformance with Dingo specification. This includes:
Collision/error statistics gathering.
Multicast address filtering, eg. the hash filter.
Initialisation and interrupt handling sequences.
Note that I've started on some of this already in v1.20.
* The probe routine needs some more work, to identify oddities such as the
REM10.
* There are still problems with the autonegotiation code; specifically, it
won't autonegotiate with some 10/100 hubs. This might simply be the hardware
not getting along, in which case there's nothing we can do, but it's still
worth investigating
* CEM28/CEM33 support. Should be able to integrate this directly from the
Linux code.
* Performance enhancements:
Full-duplex on 10Mbit networks.
Virtual shared-memory mode.
Early send and receive modes.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
* Conformance with Dingo specification. This includes:
Collision/error statistics gathering.
Multicast address filtering, eg. the hash filter.
Initialisation and interrupt handling sequences.
Note that I've started on some of this already in v1.20.
* The probe routine needs some more work, to identify oddities such as the
REM10.
* There are still problems with the autonegotiation code; specifically, it
won't autonegotiate with some 10/100 hubs. This might simply be the hardware
not getting along, in which case there's nothing we can do, but it's still
worth investigating
* CEM28/CEM33 support. Should be able to integrate this directly from the
Linux code.
* Performance enhancements:
Full-duplex on 10Mbit networks.
Virtual shared-memory mode.
Early send and receive modes.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
- Split syscons source code into manageable chunks and reorganize
some of complicated functions.
- Many static variables are moved to the softc structure.
- Added a new key function, PREV. When this key is pressed, the vty
immediately before the current vty will become foreground. Analogue
to PREV, which is usually assigned to the PrntScrn key.
PR: kern/10113
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
- Modified the kernel console input function sccngetc() so that it
handles function keys properly.
- Reorganized the screen update routine.
- VT switching code is reorganized. It now should be slightly more
robust than before.
- Added the DEVICE_RESUME function so that syscons no longer hooks the
APM resume event directly.
- New kernel configuration options: SC_NO_CUTPASTE, SC_NO_FONT_LOADING,
SC_NO_HISTORY and SC_NO_SYSMOUSE.
Various parts of syscons can be omitted so that the kernel size is
reduced.
SC_PIXEL_MODE
Made the VESA 800x600 mode an option, rather than a standard part of
syscons.
SC_DISABLE_DDBKEY
Disables the `debug' key combination.
SC_ALT_MOUSE_IMAGE
Inverse the character cell at the mouse cursor position in the text
console, rather than drawing an arrow on the screen.
Submitted by: Nick Hibma (n_hibma@FreeBSD.ORG)
SC_DFLT_FONT
makeoptions "SC_DFLT_FONT=_font_name_"
Include the named font as the default font of syscons. 16-line,
14-line and 8-line font data will be compiled in. This option replaces
the existing STD8X16FONT option, which loads 16-line font data only.
- The VGA driver is split into /sys/dev/fb/vga.c and /sys/isa/vga_isa.c.
- The video driver provides a set of ioctl commands to manipulate the
frame buffer.
- New kernel configuration option: VGA_WIDTH90
Enables 90 column modes: 90x25, 90x30, 90x43, 90x50, 90x60. These
modes are mot always supported by the video card.
PR: i386/7510
Submitted by: kbyanc@freedomnet.com and alexv@sui.gda.itesm.mx.
- The header file machine/console.h is reorganized; its contents is now
split into sys/fbio.h, sys/kbio.h (a new file) and sys/consio.h
(another new file). machine/console.h is still maintained for
compatibility reasons.
- Kernel console selection/installation routines are fixed and
slightly rebumped so that it should now be possible to switch between
the interanl kernel console (sc or vt) and a remote kernel console
(sio) again, as it was in 2.x, 3.0 and 3.1.
- Screen savers and splash screen decoders
Because of the header file reorganization described above, screen
savers and splash screen decoders are slightly modified. After this
update, /sys/modules/syscons/saver.h is no longer necessary and is
removed.
fix; it doesn't address the problem of removing the module. If you do
the following:
vinum stop
fsck /dev/vinum/VOLUME
you *will* get a system crash. What we need is a cdevsw_remove
corresponding to cdevsw_add, but that hasn't been written yet.
Submitted-by: phk
usbd_get_interface_descriptor
2) remove soft reset. It's been dropped from the USB Mass Storage Bulk-Only
Specification
3) move the clear feature halt to the reset routine.
positively not let ti_encap() fill up the TX ring all the way and wrap
around. This fixes a potential transmit lockup where a really fast
machine (or particular TX traffic pattern) can overrun the end of the
ring.
Reported by: John Plevyak <jplevyak@inktomi.com>
Also removed the BSDI support (for now)
This allows the driver to be loaded/unloaded as a KLD
and loaded in the boot loader phase whithout making a custom kernel.
corresponding variable `rc_wakeup_started' in rev.1.36 but broken
again in rev.1.37. This bug only caused excessive polling (it gave
NRC activations for each of the SWI handler and the timeout handler
instead of 1 of each).
Moved cdevsw attachment from the driver probe routine to the driver
attach routine.
via an IBM PCI-PCI bridge (82351 or 82352 or 82353)
The driver must identify if it is on a secondary PCI bus, which is
created via the IBM PCI-PCI bridge. If it is, then it must initialise
the IBM PCI-PCI bridge correctly.
To do this, the following new functions are added.
Because they use the pcici_t tag, they are considered 2.2 compatibility APIs
pcici_t * pci_get_parent_from_tag(pcici_t tag);
int pci_get_bus_from_tag(pcici_t tag);
(The _from_tag suffix is used to prevent clashes with similarly named
newbus PCI API functions)
Submitted by: Anton Berezin <tobez@plab.ku.dk>
Reviewed by: Doug Rabson <dfr@nlsystems.com>
Reworked by: Me (roger)
The cdevsw_add() function now finds the major number(s) in the
struct cdevsw passed to it. cdevsw_add_generic() is no longer
needed, cdevsw_add() does the same thing.
cdevsw_add() will print an message if the d_maj field looks bogus.
Remove nblkdev and nchrdev variables. Most places they were used
bogusly. Instead check a dev_t for validity by seeing if devsw()
or bdevsw() returns NULL.
Move bdevsw() and devsw() functions to kern/kern_conf.c
Bump __FreeBSD_version to 400006
This commit removes:
72 bogus makedev() calls
26 bogus SYSINIT functions
if_xe.c bogusly accessed cdevsw[], author/maintainer please fix.
I4b and vinum not changed. Patches emailed to authors. LINT
probably broken until they catch up.
Reformat and initialize correctly all "struct cdevsw".
Initialize the d_maj and d_bmaj fields.
The d_reset field was not removed, although it is never used.
I used a program to do most of this, so all the files now use the
same consistent format. Please keep it that way.
Vinum and i4b not modified, patches emailed to respective authors.
of the current interrupt trasaction.
- Do not schedule the next interrupt transaction if the pipe is being
aborted or the last round of the interrupt transaction ended with error.
Submitted by: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>
- Call ums_disable() to abort the pipe.
- Do not wake up processes which has been waiting or polling for mouse
data. It won't be available anymore.
Submitted by: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>
disable_intr() does non-recursive locking in the SMP case. This should
fix cy-driver-related panics when SMP is configured.
Broken in: rev.1.73 (3.1 and -current)
Allow chipset drivers to specify the direct-mapped DMA window's mask in
preparation for tsunami support. Previous chipsets' direct-mapped DMA
mask was always 1024*1024*1024. The Tsunami chipset needs it to be
2*1024*1024*1024
Reviewed by: Doug Rabson <dfr@nlsystems.com>
preparation for tsunami support. Previous chipsets' direct-mapped DMA
mask was always 1024*1024*1024. The Tsunami chipset needs it to be
2*1024*1024*1024
These changes should not affect the i386 port
Reviewed by: Doug Rabson <dfr@nlsystems.com>
only support 'mirroring' the vendor and device ids, so we don't
lose any information. Certain revisions of the aic7880 will not
perform the mirroring so to match all possiblities would double
the number of table entries. This change also allows us to match
things like the 2944B which I missed in the original table.
commands are outstanding. You'd think they'd just clear the IDLE bit,
but alas, no. Delay until all pending mailbox commands have completed
in aha_cmd to work around this.
Report sync rates correctly on Fast Adaptec cards. Clones may still be
reported incorrectly since there is no documenation on how they report
extended sync values.
Clean up some unused fields in the aha softc.
SIS/VIA/ OPTi chipset PCI bus workarounds.
These make the Bt878/879 chips stabler on certain
older and non-intel motherboards.
Use options BKTR_430_FX_MODE
or options BKTR_SIS_VIA_MODE
to enable these modes.
Also rename 849 to 849A
in the transmit code: the TX descriptor ring, and a 'shadow' ring of mbuf
pointers, one for each TX descriptor. When transmitting a packet that
consists of several fragments in an mbuf chain, we link each fragment
to a descriptor in the TX ring, but we only save a pointer to the mbuf
chain. This pointer is saved in the shadow ring entry which corresponds
to the first fragment in the packet. Later, ti_txeof() can release the
whole chain with a single m_freem() call. (We need the second ring to
keep track of the virtual addresses of the mbuf chains.)
The problem with this is that the Tigon isn't actually through with the
mbuf chain until it reaches the last fragment (which has the TI_BDFLAG_END
bit set), however the current scheme releases the mbuf chain as soon as
the first fragment is consumed. This is wrong, since the mbufs can then
be yanked out from under the Tigon and modified before the other fragments
can be transmitted.
The fix is to make a one line change to ti_encap() so that it saves the
mbuf chain pointer in the shadow ring entry that corresponds to the last
fragment in TX ring instead of the first. This prevents the mbufs from
being released until the last fragment is transmitted.
Painstakingly diagnosed and fixed by: Robert Picco <picco@mail.wevinc.com>
Brought to my attention by: dg
manager and prevented IOPort allocation beyond the first EISA slot from
working. subr_rman.c should have trapped this on the way into the system
rather than tripping over the wreckage.
Head banged into wall repeatedly by: "Matthew N. Dodd" <winter@jurai.net>
Honor the 'bus reset at startup' option now that the XPT properly
handles transfer negotiation in this scenario.
Honor the sync rate settings on Ultra2 controllers. We would
always negotiate at the fastest speed. Oops.
aic7xxx.h:
Whitespace.
aic7xxx.seq:
Fix a minor nit that would cause the controller to miss the update
of the negotiation required bitmask causing the negotiation to
be delayed by a command.
driver lacks error recovery and still needs more testing, but it's
about time I got it under revision control.
Submitted by: Tekram Inc.
Bus Space/DMA and cleanup: gibbs
- Mention that the 6Mbps turbo adapters are supported in HARDWARE.TXT
and RELNOTES.TXT and the wi.4 man page
- Mention turbo adapters in the wicontrol.8 man page and provide a
complete table of available transmit speed settings
Implement priorities.
GENERIC, LINT, files:
Remove remarks about ordering of device names.
GENERIC, LINT:
Sort the devices alphabetically in LINT and GENERIC.
The specific intent of this commit is to pave the way for importing
Compaq XP1000 support. These changes should not affect the i386 port.
Reviewed by: Doug Rabson <dfr@nlsystems.com>
(actually, he walked me through most of it & deserves more than reviewd-by
credit )
Fixed problems:
LS120/ZIP drives still currupted data.
Reworked once again, buffered I/O is just ignoring any sizehints
it is given :(
Now the atapifd driver splits up requests for devices that has
limitted transfer size.
ISA only configs fails on boot with interrupt timeouts.
The new-bus integration introduced a bug where the softc ptr
was lost during the probe.
Some minor cleanups and rearrangements as well.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, again you have been warned :)
Notebook owners should be carefull that their machines dont suspend
as this might cause trouble...
But please tell me how it works for you!
Enjoy!
motherboard will have a card for the "motherboard" on slot 0.
eisa0: <EISA bus> on motherboard
mainboard0: <ASU5101 (System Board)> at slot 0 on eisa0
This should stop the probe "detecting" an EISA bus everywhere that has
a 'controller eisa0' line regardless of whether it's really there.
Change Intel GPIO mask to hopefully stop turning the Intel Camera off
Fixed tuner selection on Hauppauge card with tuner 0x0a
Replaced none tuner with no tuner for Theo de Raadt <deraadt@openbsd.org>.
Ivan Brawley <brawley@internode.com.au> added
the Australian channel frequencies.
Clean up the handling of failure modes in our attach so we don't free
resources twice. ahc_free() will do all of the work for us (as would
be required by an unload event) so we only need to handle resources that
the softc has not taken ownership of.
Fixed problems:
LS120 drives currupted data.
The workaround for drives not supporting upto 64K transfers
has been reworked. It works now both on LS120 & ZIP drives.
ISA only configs wont compile.
Fixed.
The ATA driver wont share interrupts.
Fixed.
The "unwanted interrupt" warning gave wrong controller.
Another lun<>unit messup from the newbus integration.
Some minor cleanups and rearrangements as well.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, again you have been warned :)
Notebook owners should be carefull that their machines dont suspend
as this might cause trouble...
But please tell me how it works for you!
Enjoy!
-Søren
docs don't seem to shed light on why this is needed, but reports from
the field indicate this helps prevent problems in this area. Ken's
changes seem to have exposed this bug, rather than caused it, as far
as I can tell.
Thanks to Jack O'Neill for tracking this down.
Submitted by: jack@germanium.xtalwind.net
Very strong 3.2 merge candidate.
Sync up device Ids with the master Adaptec list.
Add probe support for the 2940 Pro although it isn't obvious that
all of the termination support is correct for this adapter yet.
tell the sequencer to pause itself for a target msg variable update. This
avoids the pause race entirely as HS_MAILBOX can be accessed without
pausing the chip.
3.2 Merge candidate.
v1.19 (1999/04/15) updates the CEM56/REM56 support.
Current bugs & misfeatures
--------------------------
* CE2 cards still not working reliably. Unclear if this is related to
packet I/O code or interrupt handling.
* Autonegotiation support remains flaky. We're now OK with 10Mbit auto
hubs, but certain combination of hardware will fail to connect.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.19 (1999/04/15) updates the CEM56/REM56 support.
Current bugs & misfeatures
--------------------------
* CE2 cards still not working reliably. Unclear if this is related to
packet I/O code or interrupt handling.
* Autonegotiation support remains flaky. We're now OK with 10Mbit auto
hubs, but certain combination of hardware will fail to connect.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.18 (1999/04/08) adds support for CEM56 and REM56 multifunction cards.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.18 (1999/04/08) adds support for CEM56 and REM56 multifunction cards.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.17 (1999/03/28) has xperimental fixes to 10Mbit autonegotiation and
CE2 input lockup.
KNOWN BUGS
==========
* Media auto-negotiation is definitely not right. It will work in most
circumstances and seems to connect OK to most 100Mbit networks, however some
pathological combinations of hubs/networks/peers seem to confuse it.
* CE2 support is somewhat flakey (ranging from 'works perfectly' to 'hangs the
machine' so far). I've fixed the probe routine and a potential lockup in
the output routine, but a lot of people still report that they can't receive
or transmit.
* You won't be able to use the modem and Ethenet parts of a multifunction card
simultaneously. This is limitation the current FreeBSD PCMCIA support.
Likewise, there is no support for CardBus devices.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.17 (1999/03/28) has xperimental fixes to 10Mbit autonegotiation and
CE2 input lockup.
KNOWN BUGS
==========
* Media auto-negotiation is definitely not right. It will work in most
circumstances and seems to connect OK to most 100Mbit networks, however some
pathological combinations of hubs/networks/peers seem to confuse it.
* CE2 support is somewhat flakey (ranging from 'works perfectly' to 'hangs the
machine' so far). I've fixed the probe routine and a potential lockup in
the output routine, but a lot of people still report that they can't receive
or transmit.
* You won't be able to use the modem and Ethenet parts of a multifunction card
simultaneously. This is limitation the current FreeBSD PCMCIA support.
Likewise, there is no support for CardBus devices.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.16 (1999/03/08) fixed BPF input hang and infinite loop on CE2
short-packet output.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.16 (1999/03/08) fixed BPF input hang and infinite loop on CE2
short-packet output.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
This driver is mostly based on the `xirc2ps' driver for Linux by Werner
Koch. Werner has even allowed his code to be distributed under a BSD licence,
making our life considerably easier -- thanks Werner!
This driver supports:
* Intel EtherExpress(TM) PRO/100 PCCARD (16-bit version)
* Xircom CreditCard CE2 / CEM28 / CEM33 / CE3 / CEM56 Ethernet adapters.
* Toshiba Advanced Network 10/100 PCCARD
* Certain Compaq Netelligent 10/100 branded cards
v1.14 has major changes to media selection code, and bugfixes in the
probe routine.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
This driver is mostly based on the `xirc2ps' driver for Linux by Werner
Koch. Werner has even allowed his code to be distributed under a BSD licence,
making our life considerably easier -- thanks Werner!
This driver supports:
* Intel EtherExpress(TM) PRO/100 PCCARD (16-bit version)
* Xircom CreditCard CE2 / CEM28 / CEM33 / CE3 / CEM56 Ethernet adapters.
* Toshiba Advanced Network 10/100 PCCARD
* Certain Compaq Netelligent 10/100 branded cards
v1.14 has major changes to media selection code, and bugfixes in the
probe routine.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
udev_t in the kernel but still called dev_t in userland.
Provide functions to manipulate both types:
major() umajor()
minor() uminor()
makedev() umakedev()
dev2udev() udev2dev()
For now they're functions, they will become in-line functions
after one of the next two steps in this process.
Return major/minor/makedev to macro-hood for userland.
Register a name in cdevsw[] for the "filedescriptor" driver.
In the kernel the udev_t appears in places where we have the
major/minor number combination, (ie: a potential device: we
may not have the driver nor the device), like in inodes, vattr,
cdevsw registration and so on, whereas the dev_t appears where
we carry around a reference to a actual device.
In the future the cdevsw and the aliased-from vnode will be hung
directly from the dev_t, along with up to two softc pointers for
the device driver and a few houskeeping bits. This will essentially
replace the current "alias" check code (same buck, bigger bang).
A little stunt has been provided to try to catch places where the
wrong type is being used (dev_t vs udev_t), if you see something
not working, #undef DEVT_FASCIST in kern/kern_conf.c and see if
it makes a difference. If it does, please try to track it down
(many hands make light work) or at least try to reproduce it
as simply as possible, and describe how to do that.
Without DEVT_FASCIST I belive this patch is a no-op.
Stylistic/posixoid comments about the userland view of the <sys/*.h>
files welcome now, from userland they now contain the end result.
Next planned step: make all dev_t's refer to the same devsw[] which
means convert BLK's to CHR's at the perimeter of the vnodes and
other places where they enter the game (bootdev, mknod, sysctl).
bad math: it does not handle page-boundary conditions, and will not
end up mapping all of the requested addresses. This will cause a panic:
page fault during probe on some systems. I have a machine that will
panic every time (when using the dpt driver) on kernel probe when there
are 5 drives installed. When there are 4 drives, it is fine.
Fix is to always allocate/deallocate an extra page.
There is also a bonus splx() fix on an early error return.
Submitted by: Mark J. Taylor <mtaylor@cybernet.com>
PR: 9367
some aha 1542B cards will return 0x7f for the unimplemented GEOMETRY
register.
This is a good 3.2 candidate.
PR: 11469
Submitted by: Thomas David Rivers
displace a real driver.
Revert rev 1.109.
Pick up a few things from elsewhere (a couple of SiS id's).
As an *experiment*, have the chip* driver claim (for reporting purposes)
IDE controllers if there isn't another PCI-aware ide or ata driver to
grab them. I've exported the match function since it could be used from
the ata-all.c code replacing ata_pcimatch() - but I have not touched the
ata code. I'd like to catch a few more devices this way, including USB
and other bridges etc.
massive thwunking to include an XS_CHANNEL value. Some changes of how
parameters are reported to outer layers (including bus, e.g.). Yet more
stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240
NVRAM.
with other reset handling in rev.1.83 but broke it in rev.1.120. The
breakage didn't seem to cause any problems even on the system which had
problems ("extra" interrupts and botched handling thereof) before rev.1.83.
It only affects multi-floppy systems anyway.
after some of the previous commits). Add in support for the 1240
dual channel ISP card. Try the dance of unmapping a PCI interrupt
if we don't configure (if that ever works it'll be helpful).
bttv's audio mux values.
Automatically locate the EEPROM i2c address and read the subsystem_vendor_id
from EEPROM and not the PCI registers.
Add NSMBUS checks around smbus/iicbus i2c bus code
Add GPIO mask for the audio mux to each card type.
Add CARD_ZOLTRIX and CARD_KISS from mailing list searches.
Tested by: Paul Reece <paul@fastlane.net.au>,
Ivan Brawley <brawley@internode.com.au> and
Gilad Rom <rom_glsa@ein-hashofet.co.il>
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it. Driver writers can do
this if it's not defined. (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
although this is pretty trivial. devclass_get_softc() is a tad more
expensive than the old com_addr() implementation. If Bruce is really
worried about the cost of this, it could always be changed so that the
softc pointer is stored in a local array again.
I'm not too happy about the result either, but at least it has less
chance of backfiring.
This particular feature could be called "a mess" without offending
anybody.
o fix DDB support
- include "opt_ddb.h"
- fix Debugger() arg
pointed out by bde
o back out pvc shadow interface support
- it is currently not used
- to make it easier to merge another implementation
o misc minor cleanup
Made a new (inline) function devsw(dev_t dev) and substituted it.
Changed to the BDEV variant to this format as well: bdevsw(dev_t dev)
DEVFS will eventually benefit from this change too.
Virtualize bdevsw[] from cdevsw. bdevsw() is now an (inline)
function.
Join CDEV_MODULE and BDEV_MODULE to DEV_MODULE (please pay attention
to the order of the cmaj/bmaj arguments!)
Join CDEV_DRIVER_MODULE and BDEV_DRIVER_MODULE to DEV_DRIVER_MODULE
(ditto!)
(Next step will be to convert all bdev dev_t's to cdev dev_t's
before they get to do any damage^H^H^H^H^H^Hwork in the kernel.)
Mark the GDB port in the config file with flags 0x80. Currently
only the sio driver checks these flags and sets up a GDB port,
but adding similar code to other serial drivers would be easy.
For backward compatibility, if an sio port is marked as the console
and no port is marked as the gdb port, the GDB port will be mapped
to the console port. This hack should go away at some point.
power management. This will only work on newer firmware revisions; older
firmware will silently ignore the attempts to turn power management on.
Patches supplied by: Brad Karp <karp@eecs.harvard.edu>
NOTE: These changes will require recompilation of any userland
applications, like cdrecord, xmcd, etc., that use the CAM passthrough
interface. A make world is recommended.
camcontrol.[c8]:
- We now support two new commands, "tags" and "negotiate".
- The tags commands allows users to view the number of tagged
openings for a device as well as a number of other related
parameters, and it allows users to set tagged openings for
a device.
- The negotiate command allows users to enable and disable
disconnection and tagged queueing, set sync rates, offsets
and bus width. Note that not all of those features are
available for all controllers. Only the adv, ahc, and ncr
drivers fully support all of the features at this point.
Some cards do not allow the setting of sync rates, offsets and
the like, and some of the drivers don't have any facilities to
do so. Some drivers, like the adw driver, only support enabling
or disabling sync negotiation, but do not support setting sync
rates.
- new description in the camcontrol man page of how to format a disk
- cleanup of the camcontrol inquiry command
- add support in the 'devlist' command for skipping unconfigured devices if
-v was not specified on the command line.
- make use of the new base_transfer_speed in the path inquiry CCB.
- fix CCB bzero cases
cam_xpt.c, cam_sim.[ch], cam_ccb.h:
- new flags on many CCB function codes to designate whether they're
non-immediate, use a user-supplied CCB, and can only be passed from
userland programs via the xpt device. Use these flags in the transport
layer and pass driver to categorize CCBs.
- new flag in the transport layer device matching code for device nodes
that indicates whether a device is unconfigured
- bump the CAM version from 0x10 to 0x11
- Change the CAM ioctls to use the version as their group code, so we can
force users to recompile code even when the CCB size doesn't change.
- add + fill in a new value in the path inquiry CCB, base_transfer_speed.
Remove a corresponding field from the cam_sim structure, and add code to
every SIM to set this field to the proper value.
- Fix the set transfer settings code in the transport layer.
scsi_cd.c:
- make some variables volatile instead of just casting them in various
places
- fix a race condition in the changer code
- attach unless we get a "logical unit not supported" error. This should
fix all of the cases where people have devices that return weird errors
when they don't have media in the drive.
scsi_da.c:
- attach unless we get a "logical unit not supported" error
scsi_pass.c:
- for immediate CCBs, just malloc a CCB to send the user request in. This
gets rid of the 'held' count problem in camcontrol tags.
scsi_pass.h:
- change the CAM ioctls to use the CAM version as their group code.
adv driver:
- Allow changing the sync rate and offset separately.
adw driver
- Allow changing the sync rate and offset separately.
aha driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
ahc driver:
- Allow setting offset and sync rate separately
bt driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
NCR driver:
- Fix the ultra/ultra 2 negotiation bug
- allow setting both the sync rate and offset separately
Other HBA drivers:
- Put code in to set the base_transfer_speed field for
XPT_GET_TRAN_SETTINGS CCBs.
Reviewed by: gibbs, mjacob (isp), imp (aha)
WaveLAN's radio modem. The default is whatever the NIC uses since NICs
sold in different countries may default to different frequencies. (The
Lose95/LoseNT software doesn't let you select the channel so it's probably
not really meant to be changed.)
- Change to the same transmit scheme as the PNIC driver.
- Dynamically set the cache alignment, and set burst size the same as
the PNIC driver in mx_init().
- Enable 'store and forward' mode by default. This is the slowest option
and it does reduce 100Mbps performance somewhat, but it's the most
reliable setting I can find. I'm more interested in having the driver
work reliably than trying to squeeze the best performance out of it.
The reason I'm doing this is that on *some* systems you may see a lot
of transmit underruns (which I can't explain: these are *fast* test
systems) and these errors seem to cause unusual and decidedly
non-tulip-like behavior. In normal 10Mbps mode, performance is fine
(you can easily saturate a 10Mbps link).
Also tweak some of the other drivers:
- Increase the size of the TX ring for the Winbond, ASIX, VIA Rhine
and PNIC drivers.
- Set a larger value for ifq_maxlen in the ThunderLAN driver. The setting
of TL_TX_LIST_CNT - 1 is too low (the ThunderLAN driver only allocates
20 transmit descriptors, and I don't want to fiddle with that now
because the ThunderLAN's descriptor structure is an oddball size
compared to the others).
adapter (and some workalikes). Also add man pages and a wicontrol
utility to manipulate some of the card parameters.
This driver was written using information gleaned from the Lucent HCF Light
library, though it does not use any of the HCF Light code itself, mainly
because it's contaminated by the GPL (but also because it's pretty gross).
The HCF Light lacks certain featurs from the full (but proprietary) HCF
library, including 802.11 frame encapsulation support, however it has
just enough register information about the Hermes chip to allow someone
with enough spare time and energy to implement a proper driver. (I would
have prefered getting my hands on the Hermes manual, but that's proprietary
too. For those who are wondering, the Linux driver uses the proprietary
HCF library, but it's provided in object code form only.)
Note that I do not have access to a WavePOINT access point, so I have
only been able to test ad-hoc mode. The wicontrol utility can turn on
BSS mode, but I don't know for certain that the NIC will associate with
an access point correctly. Testers are encouraged to send their results
to me so that I can find out if I screwed up or not.
network adapters. These are all PCMCIA devices (the ISA version is a
PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a
wicontrol utility to read and write some of the card's parameters.
Note: I do not have access to a WavePOINT access point, so I have only
been able to test this driver in ad-hoc (point to point) mode. The
wicontrol utility allows programming the desired service set name (SSID)
and enabling BSS mode, but I can't tell for sure if it works (I know the
card switches modes, but I can't verify that it joins a service set
correctly).
This driver was written using information gleaned from the Lucent HCF Light
library, which is an API library designed to simplify driver development
for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light
is missing certain features (like 802.11 frame encapsulation!) which are
available only in the proprietary complete HCF code, which is not available
to the public. This driver uses none of the HCF Light code: it's very ugly
and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11
frames, everything else is encapsulated as 802.3.
(It would be easier to just get the Hermes programming manual, but that's
not publically available either. For those who are wondering, the Linux
WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in
object code form only. So much for supporting open source sofware.)
Multicast filter support is implemented, however it appears that the
filter doesn't work: programming in one IP mutlicast group enables them
all.
bug in the stats accounting (nicSendBDs counter was bogus when TX ring was
configured to be in host memory).
Update if_tireg.h to look for new firmware fix level.
* Make the network code in the bootstrap more chatty (helps debugging)
* Add nfs root stuff to cpu_rootconf(). I also added a check to make sure
it really was netbooting which allows the use of the same kernel for local
and network boots.
* Tweak the de driver so that it takes the speed setting from the console
for the alpha (some PWSs have broken de chipsets). This is the same
behaviour as NetBSD/alpha.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu>
if there's benefit to setting it to the exact amount, it appears the
card has 32K of ram, and 8K is used for outgoing packets, that would
be something like a queue limit of 5 packets. I don't think that's
useful...)
PR: 11456
Submitted by: Stephen J. Roznowski <sjr@home.net>
If a drive has gone down and has dirty buffers associated with it,
we'll get a panic when we try to vn_close it. Check for this
situation and discard any buffers; they're toast anyway.
Only complain about usage count if DEBUG_WARNINGS is set.
check_drive:
Change parameter name from drivename to devicename.
Get the check for a referenced drive right.
If the partition isn't a vinum drive, set the last error to ENODEV.
vinum_scandisk:
Change parameter name from drivename [] to devicename [].
resource. Avoids useless interrupts occurring between the allocation
of the interrupt resource and the final initialisation of the
kernel. Cause of these interrupts is unknown (a resuming device?).
from ever catching up to the transmit consumer index. We can't let this
happen because ti_txeof() depends on the assumption that producer == consumer
means the ring is empty, and producer != consumer means the ring has some
number of active descriptors in it.
This will allow software teletext/intercast/subtitles decoding
while watching a TV station.
Based on code from Hiroki Mori <mori@infocity.co.jp> but reworked by
myself.
Add new #ifdef. By defining BKTR_NO_MSP_RESET you can prevent the
MSP34xx being reset by the bt848 driver. This is handy
if you pre-initialise the MSP34xx stereo audio chip in another
operating system first (eg MS Windows).
Suggested by: Randal Hopper<aa8vb@ipass.net>
Suggested by: Yuri Gindin <yuri@xpert.com>
1:
s/suser/suser_xxx/
2:
Add new function: suser(struct proc *), prototyped in <sys/proc.h>.
3:
s/suser_xxx(\([a-zA-Z0-9_]*\)->p_ucred, \&\1->p_acflag)/suser(\1)/
The remaining suser_xxx() calls will be scrutinized and dealt with
later.
There may be some unneeded #include <sys/cred.h>, but they are left
as an exercise for Bruce.
More changes to the suser() API will come along with the "jail" code.
style pci drivers with a simple one-line change to use a module that
registers itself under new-bus and should in theory enable just about all
of the pci drivers to be loadable (kldload and loader(8)) but without
having the impact of converting the APIs yet.
This also fixes the problem of having undefined variables when only
new-style pci drivers are present.
Convert to new bus and bus dma.
Use latest PCI API.
bt_pci.c:
Fix a few bugs in how resourses are released left over from
when this driver was converted to new bus.
Interrupts under the new scheme are managed by the i386 nexus with the
awareness of the resource manager. There is further room for optimizing
the interfaces still. All the users of register_intr()/intr_create()
should be gone, with the exception of pcic and i386/isa/clock.c.
2) rename variables to be more conclusive.
3) fix a problem in uhci_ii_done. Avoid collecting all the status's of the
TD's, we only need to one from the last inactive one.
4) Change the errorcount from 2 to 3 (see UHCI spec.).
- fix cut/paste problem. :-)
- don't forget to call isa_dmacascade()
- reset the port after we release resources.
That last one is a trap to watch out for.. The isa bus driver uses the
same port/irq/mem/etc variables for the initial probe hints as it does
for allocation/deallocation tracking. Releasing a resource clears the
variable and then you loose the hint during attach.. (ouch!)
had a quirk that made a shim rather hard to implement properly and it was
just easier to convert the drivers in one go. The changes to the
buslogic driver go beyond just this - the whole driver was new-bus'ed
including pci and isa. I have only tested the EISA part of this so far.
Submitted by: Doug Rabson <dfr@nlsystems.com>
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
2) create function usbd_errstr which turns a usbd_status into a sensible
error message
3) Change the printf in DPRINTF to logprintf which is a define for
log(KERN_DEBUG, x)
Fixed problems:
Promise controllers was not always set up correctly.
Parantheses are a good thing, fixed.
Some older CDROM's could hang the probe.
Proberly wait for the drive to catch its breath after IDENTIFY.
Some CD writers fails because they dont support rezero.
Rearranged the code to not use rezero.
Warnings now that we use EGCS.
Fixed.
Fix a potential drive deadlock when saving config to a non-existent
drive.
Add debug calls to catch occasional deadlocks on drives. The problem
(above) is probably gone, but the debug checks remain for a while.
is probably gone, but the debug checks remain for a while.
update_plex_config: Catch yet another divide-by-zero problem when
detaching the last subdisk from a striped plex.
Uncovered-by: Michael Reifenberger <root@nihil.plaut.de>
are pending I/O transactions. It is not clear that is works 100% of
the time under SMP, but since the bt_cmds() that are sent after other
CPUs are started are not critical, the driver will function until I
can figure out why this is the case.
Oh, I forgot to mention: this driver also works on FreeBSD/alpha (big
thanks to Andrew Gallatin). And there is a 2.2.x version available for
those who stubbornly refuse to upgrade.
Networks Tigon 1 and Tigon 2 chipsets. There are a _lot_ of OEM'ed
gigabit ethernet adapters out there which use the Alteon chipset so
this driver covers a fair amount of hardware. I know that it works with
the Alteon AceNIC, 3Com 3c985 and Netgear GA620, however it should also
work with the DEC/Compaq EtherWORKS 1000, Silicon Graphics Gigabit
ethernet board, NEC Gigabit Ethernet board and maybe even the IBM and
and Sun boards. The Netgear board is the cheapest (~$350US) but still
yields fairly good performance.
Support is provided for jumbo frames with all adapters (just set the
MTU to something larger than 1500 bytes), as well as hardware multicast
filtering and vlan tagging (in conjunction with the vlan support in
-current, which I should merge into -stable soon). There are some hooks
for checksum offload support, but they're turned off for now since
FreeBSD doesn't have an officially sanctioned way to support checksum
offloading (yet).
I have not added the 'device ti0' entry to GENERIC since the driver
with all the firmware compiled in is quite large, and it doesn't really
fit into the category of generic hardware.
Repeatedly-tripped-over-by: Vallo Kallaste <vallo@matti.ee>
When VINUMDEBUG is set, free any memory found still
allocated.
Only log errors if DEBUG_EXITFREE is set.
board versions with no BIOS. Separate mailbox interrupts from
IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not
after you clear it (potential race condition). Clear out older broken
BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup
if already in LVD mode. Note usage of presumptive 1040C revision. For
all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state
as unknown as well as marking the need to do a getpdb on targets- after
a LIP for certain the f/w has to do PRLI/PLOGI for all targets again
and marking f/w state as unknown gives us a fighting chance to (start
to) hold up for that to complete.
that will SBusify an isp header or the lun/target portions of a request IOCB-
and have these only valid iff __sparc__ (no non-sparc SBus machine that *I*
know about).
free_vinum: Wait for daemon to stop by checking the
vinum_conf.flags & VF_DAEMONOPEN.
vinum_modevent:
When compiled with VINUMDEBUG, check if we have
forgotten to free any memory, and log an error if we
have.
vinumopen: Allow open of an empty subdisk (otherwise we can't
initialize it).
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
VINUM_<object>CONFIG: return ENXIO rather than EFAULT if an object
doesn't exist.
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
vinum_scandisk: increment drive use count when we find a good one.
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
Remove unused (and braindead) functions volume_index, plex_index,
sd_index and drive_index.
Add a flag VF_CREATED for volumes. VF_NEWBORN was being used in two
capacities, and they clashed, my Lord, they clashed.
find_object: restructure the search loop as a result of the change in
variable use.
Decrement object use count in the remove_<object> functions, not in
the free_<object> functions, which are often called with partially
initialized (and uncounted) objects.
plexes_used and volumes_used. Now these fields are only informative,
and the <object>_allocated count is used for searches, etc. This also
required checking the object state before doing things with the
presumed object.
Problems-reported-by: Kiril Mitev <kiril@ideaglobal.com>
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
longjmp. I suspect that the occasional double panic may be the result
of incorrect parameters to longjmp. This happens, of course, like the
entire file, only with -DVINUMDEBUG.
give_sd_to_plex: Don't set Raid-5 subdisk state here.
config_subdisk: handle the name parameter correctly when the subdisk
was referenced in a previous plex definition. The
name parameter must come first.
Handle autosizing relatively correctly. There is
still a danger of losing drive space if problems
occur with an autosized subdisk.
Set state to empty, not up, when complete. This also
solves a nagging problem about enforcing the need to
initialize RAID-5 plexes.
config_plex: handle the name parameter correctly when the plex
was referenced in a previous volume definition. The
name parameter must come first.
Handle initial state better.
update_plex_config:
Calculate the trim factor for RAID-5 plexes correctly.
Set the number of down subdisks correctly when reading
from disk config.
settings you've just sent them and return random values if you follow
the set by a get. This causes problems when you latter run a Tag-enabled
command when you've command tagged mode off.
Recognize aic7895 controllers that have been "acquired" by a RAIDPort
card as normal aic7895s.
Recognize the aic7815 Raid Parity/Memory controller chip and notify
the user that it's RAID functionality will be ignored.
Don't mess with the IRQMS bit in the host control register unless
we are an aic7770 chip.
Use calling context to determine if the card is already paused when
we update the target message request bit field in controller scratch
ram. Looking at the paused bit in the HCNTRL register opened up a
race condition.
Insert delays in the target message request update routine as a temporary
work around for what looks like a chip bug. I'm still investigating this
one.
Fix the Abort/Abort Tag/BDR handler to pull its message from the message
buffer in our softc instead of attempting to get it from a register on
the controller. The message is never recorded by the controller in the
new message scheme.
Don't rely on having an SCB when a BDR occurs. We can issue these during
invalid reconnects to.
Fix a few cases where we were restarting the sequencer but then still
falling out of a switch statement to unpause the sequencer again.
This could cause us to mess up sequencer state if it generated another
pausing interrupt between the time of the restart and unpause.
Kill the 'transceiver settle' loop during card initialization. I
failed to realize that a controller that is not connected to any
cables will never settle or enable the SCSI transceivers at all.
The correct solution is to monitor the IOERR interrupt which indicates
that the transceiver state has changed (UW<->LVD).
Modify the aic7xxx assembler to properly echo input when stdin is not
a tty.
remove the splbio() around the call to launch read requests.
launch_requests:
Move the splbio() protection outside the entire launch_loop. The
previous location was causing problems with IDE drives, where the
call to the strategy routine often did not complete until after
complete_rqe deallocated the request structure.
Solution-independently-found-by: Russell Neeper <r-neeper@tamu.edu>
Problem-reported-by: Vallo Kallaste <vallo@matti.ee>
John Saunders <john@nlc.net.au>
Bernd Walter <ticso@cicely.de> (maybe)
Check for partition types FS_VINUM and FS_UNUSED. Accept both, but
complain about FS_UNUSED. At a later date, only FS_VINUM will be
accepted.
Threatened-since: over a year
Add a flag `force' (VF_FORCECONFIG) to force name changes of
existing drives.
config_drive:
If the drive already has a vinum label, and name doesn't match the
specified drive, do it anyway if the 'force' flag is specified.
finish_config:
Reset the `force' flag.
Continually-tripped-over-by: Karl Pielorz <kpielorz@tdx.co.uk>
give_sd_to_drive:
If the drive is down, take the subdisk down and don't try to fix
things.
update_plex_config:
Don't try to update the config parameters of a plex which isn't
fully configured (state plex_init or plex_unallocated).
Correctly calculate the amount to trim off a striped or RAID-5 plex
whose size is not a multiple of the stripe size.
compiled with or without debugging support. This enables us to catch
(fatal) mismatches between the kernel and userland.
Coalesce flags VINUM_DISKCONFIG and VINUM_READING_CONFIG. They did
essentially the same thing.
Add VINUM_BIGDRIVE for pretending we have macho hardware.
pretends that each drive is 100 times as large as it really is. Not
for use at home.
Coalesce flags VINUM_DISKCONFIG and VINUM_READING_CONFIG. They did
essentially the same thing.
This solved a problem where 'vinum resetconfig' only reset half
the drives.
Reported-by: Brad Knowles <blk@skynet.be>
Karl Pielorz <kpielorz@tdx.co.uk>
Change the super device. We now have three super devices:
1. The normal superdevice used by vinum(8).
2. The superdevice used by vinum(8) when compiled with debug support.
3. The superdevice used by the daemon.
This method allows vinum(8) to determine debug mismatches. Also check
correctly for the device type. The old code did not check all bits of
the minor number.
Reported-by: a cast of thousands, most recently by Brad Knowles
<blk@skynet.be>.
gave yet another internal register layout model for what is
*still* the same architecture. I hope they saved billyuns of gates
'coz otherwise this is *really* annoying.
thwank in register layout goop). A different mboxcmd approach. Some PDB change
infrastructure. Some better management of loopdown/loopup events (keep them
distinct from resource starvation for simq freeze/unfreeze actions).
The old VN device broke in -4.x when the definition of B_PAGING
changed. This patch fixes this plus implements additional capabilities.
The new VN device can be backed by a file ( as per normal ), or it can
be directly backed by swap.
Due to dependencies in VM include files (on opt_xxx options) the new
vn device cannot be a module yet. This will be fixed in a later commit.
This commit delimitted by tags {PRE,POST}_MATT_VNDEV
chip int. and ext. clock synchronisation). Fixed workaround for
transmit threshold underrun. Added volatile keyword to CSR_READ_* and
CSR_WRITE_* macroses. Added DELAYs to eliminate randomness caused
by processor speed. Fixed all TXCON and RXCON registers to be accessed
only when chip is idle, as manual told. Changed epic_init_phy to
drop link by isolating and going loopback, should should force link
partner to restart autonegotiation.
PR: kern/10535, kern/9742, kern/10575
Submitted by: Peter Jeremy, David Greenman
a wierd double-queue arrangement.. It always empties the if_snd queue
then puts the transmit packets into a different queue that is limited
by the number of TX descriptors and does it's own discards...
This should stop the boot-time XXX warning anyway.
MMalloc: save the time at which the request was granted, remove more
crud.
FFree: add a circular buffer of the last 64 Free requests if
DEBUG_MEMFREE is set.
after the volume had been fully operational; involves a change in the
use of the VF_NEWBORN flag. Now if you add a plex to a volume which
is up, the plex will be down and the subdisks stale. You need to
explicitly start the subdisks, which copies data from the good
subdisks to the uninitialized ones.
Stumbled-over-by: Ludwig Pummer <ludwigp@bigfoot.com>
give_sd_to_drive:
correct method to give the entire largest chunk of drive to the
subdisk. Now it's enough to specify a length, and vinum will give
you as much as it can. Not to be recommended except for empty
drives.
Correct a bogon which made vinum refuse to give the last sector of
a drive to a subdisk.
Last-reported-by: Ludwig Pummer <ludwigp@bigfoot.com>
Change %q formats to %ll before the former go away. This doesn't make
much difference, since kernel kvprintf currently doesn't support
either, and the messages in question are just error messages.
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
Move the Olicom token ring driver to the officially sanctionned location of
/sys/contrib. Also fix some brokenness in the generic token ring support.
Be warned that if_dl.h has been changed and SOME programs might
like recompilation.
The i++ loop from 1..1000 is too small on very fast machines like
PII 450 MHz. Increasing the loop from 1..100000 lets the machine
access PHY. After this patch it's possible to use a SMC PCI card
on a HP Kayak XA series PC Workstation. Workaround until this fix
was to enable debugging in the driver (#define EPIC_DEBUG 1).
Without that patch you get an undefined state:
while true
do
ifconfig -a | grep status:
done
The status messages flaps between twwo values, but not
"connected".
Obtained from: Ustimenko Semen <semen@iclub.nsu.ru>
determine IRQ and DRQ information.
Fix a bug that would cause us to attempt to retrieve extended sync
rate information on cards/firmware revs that do not support that command.
config info. On early revision cards (742a), the EISA register space,
other than the location used to determine the address of the card's main
command ports, is write only.
reports on those most welcome!
Fixed problems:
Hang on probe on "fantom" devices.
The probe now use a timeout to avoid hangs if no interrupt
is recevied.
There has also been more general code clenaups, and some reorgs.
connection.
Clean up support for devices featuring the multiple target SCSI ID feature.
On aic7890/91/96/97 chips, we can now assume the target role on multiple
target ids simultaneously. Although these chips also have sufficient
instruction space to hold to support the initiator and target role at the
same time, the initiator role is currently disabled as it will conflict
(chip design restriction) with the multi-tid feature. I'll probably add
a nob to enable the initiator (there-by disabling multi-tid) some time
in the future.
Return queue full or busy, depending on the tagged nature of the incoming
request, if our command input queue fills up in host memeory.
Deal with accept target I/O resource shortages.
If we get an underrun on a transaction that wasn't supposed to transmit
any data, don't attempt to print out the S/G list. The code would
run until hitting a non-present page. (oops)
interrupts are enabled, this kills the last "unwanted interrupts"
(and there is no ugly hacks like in the old driver to avoid them).
COmmand interrupt devices are now supported, this applies mostly
to older CDROM's and apparently also the ZIP.
Fixed problems:
Number of total sectors wrong on some older drives.
Fixed by not using the LBA size unless we know its valid.
There has also been more general code clenaups, some reorgs also.
Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver.
Fixed problems:
Dont use more sectors/intr than the drive supports.
Fix announce of > 8.4G disks.
Dont call ad_interrupt/ad_transfer when no disks config'd.
Use the right page# for CDR write mode params.
Fix breakage when no PCI support in kernel.
Implement DEVFS stuff.
General code clenaup.
Change VINUM_SAVECONFIG: it now requires a parameter. 0 means
"configuration updates are finished, please save", and 1 means "please
just save the config". This second meaning is invoked by the new
"saveconfig" command to vinum(8).
Recognize "referenced" drives by the lack of a slash in the device
name, not by a NUL character.
vinum_scandisk: return error indication (ENOENT if we can't find any
vinum drive, otherwise 0).
VINUM_SAVECONFIG: change parameters.
Don't save config while we're reading it from disk.
Change the way we handle the daemon: if we can't communicate with it
for 1 second (which is possible), start a new one. The daemon saves
its pid in daemonpid; on each iteration of the main loop the daemon
checks whether it's still in favour. If not, it silently exits.
Also, when trying to communicate with the daemon, check daemonpid
first. If it's set to 0, don't even try.
Rename the VF_KERNELOP to VF_DISKCONFIG and checkkernel () to
checkdiskconfig (), which better describes their function.
Disable configuration updates if we have an error reading in the
configuration. This stops a "shoot-in-foot" problem where a mistake
can cause the configuration to be obliterated.
Tidy up some messages, which included superfluous \ns.
Recognize RAID-5 configuration information even in the non-RAID-5
version. This fixes shoot-in-foot problems where starting the wrong
version of vinum would kill RAID-5 plexes.
Recognize drives that have been referenced, but for which no physical
location is known. This is part of a modification which will
ultimately allow incrementally reading configurations. Such drives
will have a device name "unknown".
New function return_drive_space () returns space to a drive.
Previously this was part of free_sd ().
give_sd_to_drive: don't do it if the subdisk needs more space than the
drive has available.
config_sd: if reading config from disk, accept plex offset, drive
offset and length specs of -1 to indicate error conditions.
parse_config: return ENOENT if the "read" command doesn't find any
drives.
remove_sd_entry: don't do it, even by force, if it's open.
If the size of a striped or RAID-5 plex is not an integral multiple of
the stripe size, trim the size until it is.
reinstate update_volume_config, which had atrophied, to recalculate
the size of a volume if a plex has shrunk due to stripe size
considerations.
vinumattach: Zero out tables after allocating them
Modify procedure at unload: if a vinum(8) has the superdev open, don't
close down. If only the daemon has it open, send the daemon a stop
request and wait for it to close the superdev, then unload.
In order to do this, create a second superdev which is opened by the
daemon. The open and close routines set a different bit in
vinum_conf.flags; otherwise the treatment is identical.
Remove opencount field in vol structure; replace by a flag bit, since
we can't count the number of opens.
Remove dead LKM grunge.
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
tulip_addr_filter() on SIOCSIFFLAGS, and was nuking the IFF_ALLMULTI
on entering tulip_addr_filter(). As a result it was impossible to run
a multicast router on a machine with a "de" interface.
Added autodetection of MMAC Osprey 100 card for
Jan Schmidt <mmedia@rz.uni-greifswald.de>. The MMAC card has an EEPROM
which contains an ASCII string beginning with "MMAC".
Corrected Hauppauge Audio Mux Mute value from 0x01 to 0x04.
Fixed a typo.
Sumitted change:
Added ALPS Tuner Type submitted by Hiroki Mori <mori@infocity.co.jp>
Submitted by: Roger Hardiman and Hiroki Mori <mori@infocity.co.jp>
Addtron appear to have their own VIA Rhine II and RealTek 8139 boards
with custom PCI vendor and device IDs. This commit updates the PCI
vendor and device lists in the vr and rl drivers so that we can probe
the additional devices.
Found by: nosing around the PCI vendor and device code list at:
http://www.halcyon.com/scripts/jboemler/pci/pcicode
This is for various Olicom cards. An IBM driver is following.
This patch also adds support to tcpdump to decode packets on tokenring.
Congratulations to the proud father.. (below)
Submitted by: Larry Lile <lile@stdio.com>
Seems to solve a problem with a mouse not responding to movements in the
X direction. Problem description is still rather vague and solution is
not exactly clear. Problem might be a compiler optimisation.
driver was thinking irq was enabled although it wasn't.
This case was particular to a no-interrupt static configuration.
Reported by: "Norman C. Rice" <nrice@emu.sourcee.com>
Now should be able to report speed for cards using NatSemi PHY.
(if you have one please let me know if it works as I
only have the Intel version)
Reviewed by: David Greenman <dg@root.com>
Submitted by Roger Hardiman.
Added ioctl TVTUNER_GETCHANSET to discover which regions the bktr driver
supports. Submitted by Vsevolod Lobko <seva@alex-ua.com>
Added BT848_GPIO_SET_EN,BT848_GPIO_SET_DATA (and GETs) to allow user land
control of the GPIO pins. This allows a Radio module on the GPIO port
to be controlled. Submitted by Vsevolod Lobko <seva@alex-ua.com>
The kernel option BKTR_GPIO_ACCESS must be used to enable the GPIO ioctls.
Submitted by: Roger Hardiman and Vsevolod Lobko <seva@alex-ua.com>
the same name. Silently return EEXIST if this happens.
vinum_scandisk: Collect drive numbers, not pointers, to avoid problems
of relocated drives.
Tripped-over-by: Bernd Walter <ticso@cicely.de>
time out on an operation. Under these circumstances, vinum(8) will
automatically start another daemon. Add a pid for the daemon, so that
an overtaken daemon will discover that it's no longer in favour, and
will crawl into a corner and die.
peripheral drivers can determine where in the devstat(9) list they are
inserted.
This requires recompilation of libdevstat, systat, vmstat, rpc.rstatd, and
any ports that depend on the devstat code, since the size of the devstat
structure has changed. The devstat version number has been incremented as
well to reflect the change.
This sorts devices in the devstat list in "more interesting" to "less
interesting" order. So, for instance, da devices are now more important
than floppy drives, and so will appear before floppy drives in the default
output from systat, iostat, vmstat, etc.
The order of devices is, for now, kept in a central table in devicestat.h.
If individual drivers were able to make a meaningful decision on what
priority they should be at attach time, we could consider splitting the
priority information out into the various drivers. For now, though, they
have no way of knowing that, so it's easier to put them in an easy to find
table.
Also, move the checkversion() call in vmstat(8) to a more logical place.
Thanks to Bruce and David O'Brien for suggestions, for reviewing this, and
for putting up with the long time it has taken me to commit it. Bruce did
object somewhat to the central priority table (he would rather the
priorities be distributed in each driver), so his objection is duly noted
here.
Reviewed by: bde, obrien
define. Add a new config flag param (ISP_CFG_NONVRAM) whose intent it is
to cause NVRAM to be ignored. Add ISPASYNC_LOOP_DOWN and ISPASYNC_LOOP_UP
isp_async enums.
Amazingly enough, I did all my scsi_sa work recently without realizing
that I had a broken isp card whose (unchangeable- it's an old old old
isp1020) NVRAM has sync mode enabled, but disconnect/reconnect disabled-
the ISP_CFG_NONVRAM is definitely warranted when you want to bloody well
ignore the NVRAM and set something sensible.
Use fast memory timing NVRAM parameter. Clean up and fix establishment
of default target parameters. Don't use NVRAM if are flagged as not to
do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC
mode but disabled disconnect/reconnect and wide!!). Fix delays after
resets. BUS resets not done in isp_init anymore- relegated to OS
specific outer layers. Fix a buglet where you can get in a loop for
a NULL xs in the completion list in isp_intr. Add in some defines that
can disable fast posting. Add in code for Loop Up/Loop Down events that
call into the outer layers as to what to do.
Do not modify m_len before passing mbuf chains to bpf.
Don't forget to pass packets to bpf when running in Crynwr mode (LINK0).
Partially based on a patch by Bill Fenner <fenner@freebsd.org>.
PR: bin/7241
Improved MSP34xx reset for bt848 Hauppauge boards.
Added detection for Bt848a.
Vsevolod Lobko<seva@sevasoft.alex-ua.com> added more XUSSR channels.
Submitted by: parts from Vsevolod Lobko<seva@sevasoft.alex-ua.com>
Obtained from: parts from OpenBSD
the screen width.
- Store the current video mode information in the `video_adapter' struct.
- The size of the `v_offscreensize' field in the VESA mode information
block is u_int16, not u_int8.
Increase the overall length of the delay by 10.
Without this a 3C509 card on my MediaGX crash box can't be reliably
read. With this it is solid.
I've left a delay multiplier in instead of just changing the base
delay because I'm surprised I had to increase it so much and expect
there may be another problem.
Change microseq offsets. Previously, offsets of the program counter where
added to the index of the current microinstruction. Make them rely on the
index of the next executed microinstruction.
Suggested by: Luigi Rizzo <luigi@labinfo.iet.unipi.it>
the startup code. Implement a call to outer framework function so that
asynchronous events can be handled (e.g., speed negotiation, target mode).
Roll internal release tags.
cycle to get rid of the old 1.31 firmware. *@!$&^@&$!&^&^!!!!!
But anyway comment it out and use new SBus 7.55 firmware. We get fast posting
with this as well as 32 luns and target mode support.
(not that this is used yet in FreeBSD, but it's ready for FreeBSD-sparc
whenever it happens....)
v_caddr_t with extreme prejudice. Here the bogons were originally
the same as for c_caddr_t (half-baked K&R support), but rev.1.95
changed one wrong cast and one harmless cast to 2 wrong casts,
and rev.1.96 only fixed the originally wrong cast.
c_caddr_t with extreme prejudice. Here the original casts to
caddr_t were to support K&R compilers (or missing prototypes),
but the relevant source files require an ANSI compiler.
apparently in accordance with style(9).
Complained-about-by: bde
vinumopen: Change check for root user to a call to suser(9)
vinumclose: Remove check for root user.
Nitpicked-by: phk
Auto Detection Mode. This leaves MSP3400C owners still unsupported.
Thanks to Gerd Knorr <kraxel@cs.tu-berlin.de> for providing some early
assistance and sample code in the linux bttv driver.
Nicolas Souchu <nsouch@freebsd.org> ported the msp_read/write/reset
functions to smbus/iicbus.
METEOR_INPUT_DEV2 now selects a composite camera on the SVIDEO port.
For true SVIDEO, use METEOR_INPUT_DEV_SVIDEO.
If you get a monochrome image from the SVIDEO port, you have
seleted the wrong input type.
Tested by: Johan Larsson<gozer@ludd.luth.se>
keyboard.
- Translate some keycode for the 84 keyboard so that the 84 keyboard
and the 101 keyboard become more compatible in terms of keycodes.
- Updated the built-in keymaps so that it is in line with the recent
changes in share/syscons/keymaps.
- Added some comment on the Pause/Break key on the 101 keyboard.
vinum_scandisk: check not only drive error, but also drive state,
before accessing the drive.
drivecmp: Remove warning messages by Backing out overly constant
declarations in revision 1.9.
Change from lkm to kld
Add field plexsdno to sd struct
Add flag VF_NEWBORN to drive, sd, plex and volume structs, indicating
that the object has just been created.
Add object types for raw (unattached) plexes and subdisks
Remove definitions of VOLNO, PLEXNO and SDNO (now functions Volno,
Plexno and Sdno)
Move revive parameters from struct plex to struct sd.
struct plex:
maintain a count of the number of inaccessible subdisks.
remove defective and unmapped regions.
Debug flags: make an enum (previously #define)
Set default revive block size to 64kB (was 32 kB)
Previously, accidentally starting the wrong version could corrupt
the RAID5 configuration.
Add functions Volno, Plexno and Sdno to replace the old defines
VOLNO, PLEXNO and SDNO.
Change from lkm to kld
Serious rewrite. No longer call set_<foo>_state to set the state
based only on other objects; instead, add functions
update_<foo>_state, which determine what the state should be by
themselves. This allows the set_<foo>_state functions to shrink
enough to be almost intelligible.
Remove flags setstate_recurse and setstate_recursing.
Remove plex defective regions and unmapped regions, which were
maintained but not used.
Change code to allow daemon to perform operations formerly kludged
into an interrupt context. Remove the DIRTYCONFIG kludge.
Change from lkm to kld
Remove #ifdefs for FreeBSD 2.c
vinumstrategy:
Support anonymous (`raw') subdisks and plexes.
Change code to allow daemon to perform operations formerly kludged
into an interrupt context. Remove the DIRTYCONFIG kludge.
No longer set B_ORDERED for reviving subdisks. I suspect this
wouldn't work correctly, and it should be done in a different manner
in vinumrevive.c
sdio: set subdisk state correctly on error
start to remove code that doesn't make any sense any more.
Remove #ifdefs for FreeBSD 2.c
Change from lkm to kld
correct type of `flags' in calls to set_drive_state.
set_drive_parms: handle anonymous drives correctly (remove them)
drive VOP functions: use the PID of the original opener to fool the
lock manager.
open_drive: be quiet about failures (they're normal when scanning the
partitions).
close_drive: lock drive before closing.
remove_drive: lock drive before deallocating.
read_drive_label: set drive up when all is OK
check_drive:
Complete rewrite. Offload most of the code to the new
vinum_scandisk
format_config:
use snprintf and %qd options to make much less emetic.
Remove old supporting functions.
vinum_scandisk:
Moved here from vinum.c
Almost complete rewrite, incorporating much of what was check_drive.
We still don't have a general way to find the drives on a system, so
get the user to supply the names via the `read' command. For each
device, try each possible compatibility slice name (there's a danger
of finding both /dev/da1h and /dev/da0s1h otherwise). Sort the
partitions found in reverse order of last update time and read them
in, setting the `update' parameter to parse_config and descendents.
save_config: rename to daemon_save_config, since the function is now
called by the daemon. Create a new function save_config which queues
the request with the daemon.
daemon_save_config: some mods to allow for the unfamiliar
environment.
Change from lkm to kld
Remove BROKEN_GDB kludge (it's not needed with klds)
Add code for interfacing with daemon
Modify device minor number encoding, use selector functions which also
permit anonymous plexes and subdisks.
Remove code for 2.x support.
Change messages to omit obvious words like 'plex' and 'subdisk.
give_plex_to_volume: invalidate subdisks being given to a plex which
is part of a volume with other plexes.
give_sd_to_plex: keep track of plex size in all cases
lock drives before closing them, to keep the daemon from getting
confused.
config_drive: handle partition type errors more gracefully
config_subdisk: set subdisk state correctly
find_drive, find_drive_by_dev, find_subdisk, find_plex, find_volume:
set VF_NEWBORN flag when a new object is created
config_drive:
Handle partition_status returns more cleverly.
Replace the device name in some cases where it got overwritten.
config_subdisk:
add parameter `update'. If the object already exists, exit without
any changes.
Set state correctly.
config_plex, config_volume:
add parameter `update'. If the object already exists, exit without
any changes.
parse_config:
move read function to vinum_scandisk.
add parameter `update' to pass to config_<object>.
remove_<object>_entry:
print a message when the object is removed.
update_plex_config:
Start defusing this function, which will go away some time.
Remove calls to update_volume_config.
Make size 64 bits
Change from lkm to kld
Remove BROKEN_GDB kludge (it's not needed with klds)
Add code for interfacing with daemon
Modify manner of determining when module is idle
Modify device minor number encoding, use selector functions which also
permit anonymous plexes and subdisks.
Remove code for 2.x support.
Move vinum_scandisk to vinumio.c
Remove myproc kludge
Keep track of open volumes by flag, not by pid (the pids caused some
problems with the lock manager).
free_vinum:
Remove unmapped and defective regions from plexes.
Wait for daemon to stop before returning
vinumopen:
Don't refuse an open if the volume is already open.
pnp system in freebsd, I'm not sure how useful this will be, but my
1542CP seems to work well in plug and play mode and does seem to
probe correctly at all the oddball addresses/irq/drqs that I tried.
[[
I was unable to get /kernel.conf or /kernel.config to read in, so
I wasn't able to verify that this method of userconfig works. that's
one thing that makes pnp so hard to use in the current scheme.
Pointers to the right new way of doing this accepted.
]]
o Add some kludges to maybe bring support for 1540A/1542A into the
driver. Since I have no 154xA cards, and the only person I know
that has them hasn't given me feedback, I'm making this commit
blind.
o Honor unit numbers that are in the config file now. This allows one
to hard wire the unit numbers (and have high unit numbers for plug
and pray devices, which can't seem to be hardwired) and have the
cards not migrate from aha1 -> aha0 should aha0 go on the fritz. I
didn't verify that hard wired scsi busses would work, but did verify
that hard wired aha addresses did work to a limited extent. Both
aha0 and aha1 must be hardwired, or when the card that was in aha0
goes away, the probe for aha0 might pick up the card that otherwise
would have been aha1.
The previous code just ignored the invalid map register, but this gave
surprising results because of the way pci_map_port() associated the map
register offset supplied with a map entry in the map array.
- Bring down the splash screen when a vty is opened for the first
time.
- Make sure the splash screen/screen saver is stopped before
switching vtys.
- Read and save initial values in the BIOS data area early.
VESA BIOS may change BIOS data values when switching modes.
- Fix missing '&' operator.
- Move ISA specific part of driver initialization to syscons_isa.c.
atkbd
- kbdtables.h is now in /sys/dev/kbd.
all
- Adjust for forthcoming alpha port. Submitted by: dfr
reorganization in rev 1.16 of i386/include/types.h which changed
stdlib.h's use of <machine/types.h>. The problem was the -I. was causing
machine/types.h to come from the current kernel source, while stdlib.h was
coming from /usr/include. /usr/include/stdlib.h is as old as the last
'make world', the machine/types.h was as new as the current source.
0 success
EAGAIN try again later
other don't call this screen saver again
- Test flags consistently to examine the status of the screen saver.
scrn_blanked: the screen saver is running
scp->status & SAVER_RUNNING: the saver is running in this vty
- Correctlyu preserve status flag bits in set/restore_scrn_saver_mdoe().
if option CY_PCI_FASTINTR is configured and mapping the irq to a
fastintr is possible. Unfortunately, this has to be optional because
pci_map_int_right() doesn't handle the INTR_EXCL flag right --
INTR_EXCL is honoured even if the interrupt needs to be non-exclusive
for other devices to work.
buffer had to be left on the head of the queue for [bufq]disksort()
to sort against. This isn't right for devices that can support multiple
active i/o's, and only the fd driver did it. "Fixing" this in rev.1.36
of ufs_disksubr.c broke the fd driver in much the same way as rev.1.52
of <sys/buf.h> broke it (see rev.1.119).
Bug reported and fix tested by: dt
black hole device. The controller will now only accept selections if
the black hole device is present and some other target/lun is enabled
for target mode.
Handle the IGNORE WIDE RESIDUE message. This support has not been tested.
Checkpoint work on handling ABORT, BUS DEVICE RESET, TERMINATE I/O PROCESS,
and CLEAR QUEUE messages as a target.
Fix a few problems with tagged command handling in target mode.
Wait until the sync offset counter falls to 0 before changing phase
after a data-in transfer completes as the DMA logic seems to indicate
transfer complete as soon as our last REQ is issued.
Simplify some of the target mode message handling code in the sequencer.
using the new pci_map_int_right() variant of pci_map_int(). Fast
interrupts work for PCI devices if and only if they are exclusive.
(The PCI interrupt mux doesn't support fast interrupts and can't
support a mixture of fast and slow interrupts even in principle.)
Don't assume that intrmask_t == unsigned in pci_map_int().
register for the PLX id). Merge the vendor's modification of the 2.2.*
release version into -current for reference. Will be cleaned up in next
commit.
Obtained from: ftp://ftp.cyclades.com/pub/cyclades/cyclom-y/freebsd/3.0/cyy30.tar.gz
capabilities, but should be a good start... Well, sort of.
It can handle W*ndows 256 color BMP file. (Other color depth probably
won't work.) The size of the image must be 320x200 or less. *sigh*
keyboard and video card drivers.
Because of the changes, you are required to update your kernel
configuration file now!
The files in sys/dev/syscons are still i386-specific (but less so than
before), and won't compile for alpha and PC98 yet.
syscons still directly accesses the video card registers here and
there; this will be rectified in the later stages.
performance and reliability a little. There was a condition before
where transmission would stall during periods of heavy traffic
exchange between two hosts. Also set the 'want interrupt' bit in
receive descriptor control words.
+ ECP parallel port chipset FIFO detection
+ DMA+FIFO parallel I/O handled as chipset specific
+ nlpt updated in order to use the above enhanced parallel I/O.
Use 'lptcontrol -e' to use enhanced I/O
+ Various options documented in LINT
+ Full IEEE1284 NIBBLE and BYTE modes support. See ppbus(4) for
an overview of the IEEE1284 standard
+ Detection of PnP parallel devices at boot
+ Read capability added to nlpt driver to get IEEE1284 compliant
printer status with a simple 'cat /dev/lpt0'
+ IEEE1284 peripheral emulation added to BYTE mode. Two computers
may dialog according to IEEE1284 signaling method.
See PERIPH_1284 option and /sys/dev/ppbus/ppi.c
All this code is supposed to provide basic functions for IEEE1284 programming.
ppi.c and nlpt.c may act as examples.
it's already on for the 2XX0) and detect the broken 1040A FIFO. Change
bzero to MEMZERO (portability with **nux). Use memcpy for same reason.
Finally detect QUEUE FULL conditions and return this as an error that
will get cam_periph_error to do it's 'tagged openings now XXX' dance.
devices dynamically. That means,
+ only one /dev/iic or /dev/smb device for each smb/iic bus to access
+ I2C/SMB device address must be given to any ioctl
+ new devices may be plugged and accessed after boot, which was
impossible previously (device addresses were hardcoded into
the kernel)
from sc, vt and sio drivers. Use instead a linker_set to collect them.
Staticize ??cngetc(), ??cnputc(), etc functions in sc and vt drivers.
We must still have siocngetc() and siocnputc() as globals because they
are directly referred to by i386-gdbstub.c :-(
Oked by: bde
used in device attach routines. At least for attaches at boot time,
actually waiting, or actually failing for malloc(..., M_NOWAIT), are
almost equally unlikely and harmless, but using M_WAITOK interferes
with automatic detection of bogus M_WAITOK's.
kernel as a pseudo-device. The changes were:
- #ifdef DEBUG -> #ifdef VINUMDEBUG
- opt_vinum.h for holding above config variable
- Fixing up a few stray problems where DEBUG wasn't optional.
- config.c -> vinumconfig.c (there's already a config.o)
- Other *.c -> vinum*.c (wasn't strictly necessary, but done in case we end
up with something else conflicting later on and we might have to have yet
more repository copies of files).
- include file paths fixups.. (ie: get them all from the kernel tree
instead of partly from the kernel and partly from /usr/include/machine)
I've spoken with Greg about this.. I hope this doesn't mess him around
too much..
in cyopen() were done in a different order than in sioopen(), partly
to (ab)use a side effect of comparam() and partly because I didn't
understand what the reset was doing (it flushes the fifos). This
turned out to be more than a cosmetic problem. Flushing the fifos
quite late is good for discarding input that arrived while the line
state was being initialized, and in the cy driver it also seems to
reduce a problem with input that arrived long ago during the previous
close (the UART loses sync too easily and for too long).
The optimisation of only waiting before issuing new commands is
obviously invalid in general and it caused many errors in NIST-PCTS.
I think the errors were mostly for characters sent with the wrong
parity, etc., after a half complete tcsetattr().
Use microtime() instead of a magic loop count to limit the wait.
The wait is a busy-wait :-( and normally takes about 500 usec.
almost works properly. Unfortunately, there is no way to flush
the rx fifo without resetting the channel, which also flushes the
tx fifo. We avoid resetting even when both fifos need to be flushed,
since resetting seems to cause the rx to lose sync if it is done
while data is arriving.
Reminded by: NIST-PCTS
hardware is interrupt-driven to a fault and sending a BREAK requires
mode switching. Always running in the BREAK-capable mode as in PR 8318
would double the overhead for sending \0's.
Reminded by: PR 8318
Use the host message loop for any unknown message types instead of performing
a reject message in the sequencer. Pass reject messages to the host
message loop too which frees up a sequencer interrupt type slot.
Default to issuing a bus reset if initiator mode is enabled. It seems
that the reset scsi bus bit is not defined in the same location for
all aic78xx BIOSes, so attempting to honor this setting will have to
wait until I get more information on how to detect it.
Nuke some unused variables.
Not tested on the if_sr, if_cx and if_ar drivers, but
expected to work just the same as it used to.
Any users of these drivers (or even better: donors
of hardware for them) please contact phk@freebsd.org
so we can test the next batch of changes to if_sppp.
as well as several functional additions.
(1) dot3 MIB support.
(2) if_media selection method support.
(3) bridge support.
(4) new boards support. Supported boards are as follows.
[PC/AT]
* Fujitsu FMV-180 series
* Allied-Telesis RE2000 series
* Allied-Telesyn AT1700 series
* Gateway Communications G/Ether series
* UB networks Access/PC ISA series
* TDK/LANX LAC-AX series
* ICL EtherTeam16i series
* RATOC REX-5586/5587
[PC-98]
* Allied-Telesis RE1000 series
* Allied-Telesis RE1000Plus/ME1500 series
* Contec C-NET(9N)E series
* Contec C-NET(98)P2 series
* UB networks Access/PC N98C+ series
* TDK/LANX LAC-98 series(not tested)
Submitted by: seki@sysrap.cs.fujitsu.co.jp (Masahiro Sekiguchi) and
chi@bd.mbn.or.jp (Chiharu Shibata)
in target mode, but we are not completing the command.
Use a template of allowed bus arbitration phases to selectively and
dynamically enable/disable initiator or target (re)selection.
Properly handle timeouts for target role transactions - just go to the
bus free state and report the error to the peripheral driver.
Checkpoint support for the XPT_ABORT_CCB function code. This currently
handles the accept tio and immediate notify ccb types, but does not
handle the continue target I/O or SCSI I/O ccb types. This is enough
to handle dynamic target enable/disable events.
Clean up the SCSI reset code so that we perform at most 1 SCSI bus
reset at initialization, the reset requested by the XPT layer.
pointed this out, but I've not seen a manifestation of this.
o Check against 0x00 as well as 0xff for geometry register, as some clone
cards don't return 0xff. Vadim Mikhailov pointed this out in PR
8743 for his Dell SCSI Array controller working in AHA-1540
emulation mode. Note that this test is likely to go away in the
future in favor of a better one Justin has recommended.
memory address space rather than IO space.. reflect this when looking for the
interface revision register.
If this is not true for them all then we probably need some smarter code.
const char *. Originally I was going to add casts from const char * to
char * in some of the pci device drivers, but the reality is that the
pci device probes return constant quoted strings.
- For transactions of 0 length, us a non-residual checking CCB type.
- Preserve command status if our interrupt handler completes a command
while we are polling for completion in aha_cmd.
floppy is used on the toshiba Libretto line of subnotebook computers.
It differs from a normal floppy in that you must use PIO rather than
DMA to transfer the data.
To enable this, you must add options "FDC_YE" to your kernel. I don't
have a machine that has a floppy and a pcmcia slot to test to make
sure that this doesn't impact normal floppy units, so I've left this as
an option.
I have ported this to -current and made an attempt to ensure that the
indentation conforms to style(9), aka the bruce filter.
Reviewed by: nate, markm
Submitted by: David Horwitt (dhorwitt@ucsd.edu)
but the present PCI probe code still thinks we are there as the pci attach
can't return an error code.
This means we are in the shared interrupt list, but have not been set up.
If we are sharing ints with another device, ohci_intr will be called and will
coredump on a NULL reference. So just return if it is called when not set up.
This fixes the symptom and not the cause.
The right answer is to let the PCI system know that the attach failed,
or to fail earlier (in the PCI probe).
The attach() is a void fn() so it can't return failure..
If we are not transfering any data, use a non S/G ccb type that doesn't
return residual information. It seems that some firmware revisions dislike
S/G ccbs with 0 length S/G lists.
Correct bt_cmd() so that we always honor command status that was latched
by our interrupt routine while polling for completion..
is more robust and common code can be used for both the target and iniator
roles. The mechanism for tracking negotiation state has also been simplified.
Add support for sync/wide negotiation in target mode and fix many of
the target mode bugs running at higher speeds uncovered. Make a first
stab at getting all of the bus skew delays correct. Sync+Wide dataout
transfers still cause problems, but this may be an initiator problem.
Ensure that we exit BITBUCKET mode if the controller is restarted.
Add support for target mode only firmware downloads. This has been
tested on the aic7880, but should mean that we can perform target mode
on any aic7xxx controller. Mixed mode (initiator and target roles in
the same firmware load) is currently only supported on the aic7890, but
with optimization, may fit on chips with less instruction space.
1) Removed 'emulation' of bitmaps in printfs, FreeBSD seems to have caught
up on that one
2) Fixed a few bugs in the timeout/timo timeout variables
3) First attempt at fixing a bug mentioned by Kazu: uhci_run is not able
start/stop his USB host on his motherboard.
apparently possible) event that the transmit start routine is
called with and empty if_snd queue, bail out instead of dereferencing
unilitialized transmit list pointers and panicking.
suggested compilation cleanups from Eklund. Wire down a hard loop id if we are
not on a platform that has the ability to get to a PCI BIOS (it still will
float to the ID it gets after a LIP but at least we can try). Clarify that the
expanded lun is based upon SCCLUN defines (in f/w).
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
PCI fast ethernet adapters, plus man pages.
if_pn.c: Netgear FA310TX model D1, LinkSys LNE100TX, Matrox FastNIC 10/100,
various other PNIC devices
if_mx.c: NDC Communications SOHOware SFA100 (Macronix 98713A), various
other boards based on the Macronix 98713, 98713A, 98715, 98715A
and 98725 chips
if_vr.c: D-Link DFE530-TX, other boards based on the VIA Rhine and
Rhine II chips (note: the D-Link and certain other cards
that actually use a Rhine II chip still return the PCI
device ID of the Rhine I. I don't know why, and it doesn't
really matter since the driver treats both chips the same
anyway.)
if_wb.c: Trendware TE100-PCIE and various other cards based on the
Winbond W89C840F chip (the Trendware card is identical to
the sample boards Winbond sent me, so who knows how many
clones there are running around)
All drivers include support for ifmedia, BPF and hardware multicast
filtering.
Also updated GENERIC, LINT, RELNOTES.TXT, userconfig and
sysinstall device list.
I also have a driver for the ASIX AX88140A in the works.
is completely empty. There is an interrupt for output completion. It
is painful to use, but polling method used in the corresponding fix in
sio.c (rev.1.152) can't be used because there is no status bit for
transmitter-empty. Now ttywait() works right.
Reminded by: NIST-PCTS
Don't call timeout() for DTR wakeup if the relevant timeout is already
active. This fixes "timeout table full" panics when sufficiently many
cyopen()s are interrupted while they are sleeping waiting for the
timeout to expire.
cards. My machine didn't tickle this problem, so I can't tell if
it fixed anything or not. However, it didn't break my already working
1542-{B,C,CF,CP} probes.
o Minor comment correction
o Minor correction in printf
were half of their physical offsets for ISA and 1/4 of their physical
offsets for PCI, while all other Cyclades offsets were physical/1 for
ISA and physical/2 for PCI. Logically wrong macros were used to scale
CY16_RESET and CY_CLEAR_INTR to the correct physical offsets.
Fixed some style bugs (mostly long lines).
use a 256 entry ring buffer of descriptersfor this purpose. This allows
the use of a simple 8bit counter in the sequencer code for tracking start
location.
Entries in the ring buffer now contain a "cmd_valid" byte at their tail.
As an entry is serviced, this byte is cleared by the kernel and set by
the sequencer during its dma of a new entry. Since this byte is the last
portion of the command touched during a dma, the kernel can use this
byte to ensure the command it processes is completely valid.
The new command format requires a fixed sized DMA from the controller
to deliver which allowed for additional simplification of the sequencer
code. The hack that required 1 SCB slot to be stolen for incoming
command delivery notification is also gone.
interrupt handlers. Instead, load and use it atomically as necessary.
This reduces mode switching overhead for "polled" mode interrupt handling
from 5 i/o's to 3 (per service type, per port) so that polled mode is only
slightly more inefficient than "interrupt" mode.
* Update drivers to the latest version of the bus interface.
The ISA drivers' use of the new resource api is minimal. Garrett has
some much cleaner drivers which should be more easily shared between
i386 and alpha. This has only been tested on cia based machines. It
should work on lca and apecs but I might have broken something.
If the next available mailbox is not in the free state, print a warning
and handle the condition as a temporary resource shortage. The condition
should never happen, but we shouldn't panic since recovery is possible.
Convert from BT'isms to AHA'isms
Don't fail the probe if the illegal command bit is set in the status
register. If the BusLogic MultiMaster probe preceeded us, it may well
have determined that the card we are attaching to was not a true MultiMaster
by sending us a command that fails on the 154X.
Reset the adapter before doing the inquiry. This provides extra sanity
and will also clear the illegal command status bit that my be left over
from the MultiMaster probe.
truncated to 32 bits.
* Change the calling convention of the device mmap entry point to
pass a vm_offset_t instead of an int for the offset allowing
devices with a larger memory map than (1<<32) to be supported
on the alpha (/dev/mem is one such).
These changes are required to allow the X server to mmap the various
I/O regions used for device port and memory access on the alpha.
base register that controls Ultra-DMA, so we need to examine all possible
base registers instead of just giving up at the first empty one.
Also, looking at the source code to the BIOS, I see that they are also
checking for 0xffffffff as an invalid value so do the same. Stefan may like
to clean this up, but at least now I can find my PCI IDE registers.
the top half to do it.
Put in a dubious check for subdisk integrity when trying to bring
up a plex where others are already up. This particular kludge is
crying out for a rewrite of the whole state code.
Add code to set_plex_state and set_volume_state to defer updates when
called from an interrupt context. This doesn't happen yet, but it
could do.
basic i/o functions, bit-banging mechanism is implemented by dev/iicbus/iicbb.c
immio.c: some bootverbose logs to watch zip+ connect/disconnect process
config_drive:
Catch an instance of anonymous drives. Doubtless many remain.
interrupt.c:
complete_rqe:
Call logrq to log iodone events if DEBUG_LASTREQS is set.
Call set_sd_state with setstate_noupdate to avoid buffered I/O out
of interrupt context.
Use define DEBUG_RESID instead of constant.
memory.c:
Remove dead expandrq() function
Malloc:
Remove directory component of file names in malloc table.
Add function vinum_rqinfo (part of the request tracing stuff).
request.c:
Add function logrq (part of the request tracing stuff).
vinumstrategy:
Check whether config needs to be written to disk, do it if so.
This is a stopgap until the Vinum daemon (bacchusd? oenologistd?)
is written.
If DEBUG_LASTREQS is set, call logrq to log user buffer headers.
launch_requests:
Correct format of debug output to console.
If DEBUG_LASTREQS is set, call logrq to log request elements.
request.h:
Add definitions for request trace.
state.c:
set_sd_state:
Check flags for setstate_noupdate. If set, don't write the config
to disk, just set global VF_DIRTYCONFIG flag. This is part of the
kludge to avoid writing config from an interrupt context.
vinumext.h:
Add declaration for vinum_rqinfo, put inside #ifdef DEBUG
Remove dead macro expandrq
vinumio.h:
Increase maximum ioctl reply length to 4 kB if DEBUG is set.
Define VINUM_RQINFO ioctl if DEBUG is set.
vinumioctl.c:
vinumioctl:
Change implementation of VINUM_DEBUG ioctl: use a debug flag
(DEBUG_REMOTEGDB) to decide whether to go into remote debugging or
not.
Implement VINUM_RQINFO.
vinumkw.h:
Define kw_info even when not debugging.
vinumvar.h:
Define VF_DIRTYCONFIG
Add pointers to request info to vinum_info if DEBUG is set.
Define setstate_noupdate
Define additional debug bits DEBUG_RESID, DEBUG_LASTREQS and
DEBUG_REMOTEGDB.
Correct a problem where an external bus reset on the 'background' channel of
a Twin Channel EISA controller could put the driver into an infinite loop.
Noticed by: Twin Channel bug, Joerg Wunsch <joerg@FreeBSD.org>
Submitted by: -Wunused, Poul-Henning Kamp <phk@freebsd.org>
Fixed bug in advansys.c where we did not properly clean up ccb_info data
structures in softc teardown.
Submitted by: Poul-Henning Kamp <phk@freebsd.org>
bogus comment to proper place.
This should fix the hangs people are seeing under very heavy load, at
least it does for me. Please let me know if you continue to have
problems.
hasseen_isadev so this will be less noisy when conflicts do exist.
Also eliminate redundant warnings about conflicts.
Requested by: bde
Reviewed by: gibbs
fxp_stop is called as the first thing in fxp_init, and if the tx desc
list has junk in it, the system may panic. This bug showed up as a side
effect of the changes in rev 1.56, but has been in the code since the
beginning.
this myself for ages, but wasn't able to get any feedback from the people
that I sent it to for testing.
Guy Helmer <ghelmer@scl.ameslab.gov> has given it a shot (before getting on
a plane, thanks!) and it appears to stop his reproducable page fault panic
in the testing he was able to do.
o For bt and aha only probe the one I/O range if a specific I/O is specified
in the config file.
o Don't even try to probe I/O ranges that have been seen already.
o If we conflict with an IRQ or DRQ, then fail the probe.
Requested by: bde, gibbs
Approved by: jkh
is a work-around from an LRAM access bug on the 940UA. In a future
microcode revision, the high 16bits of residual information will be moved
to a safe location and we'll return to 32bit residuals. Since we only
allow 64KB I/O, 16bits is enough.
DEB macro). There are probably quite a few other messages that warrant
a similar treatment, and many more that should be converted to plain
log messages (e.g. "WARNING: wrintr but write DMA inactive!"). Now
that I think of it, same goes for the CAM code (e.g. the famed "tagged
openings" message)
Disable DPARCKEN in the DSCOMMAND0 register on the aic7890/91/96/97.
Parity checking is broken for some chip/MB combinations and this
is the work around recommended by Adaptec.
dpt_pci.c:
Remove a superflous '{' that prevented DPT_ALLOW_MEMIO from working.
pcireg.h:
Add a definition for Parity Error Reponse bit in the PCI Space
command register.
queued.
Perform dma segment setup outside of splcam protection as this can take
some time and the protection is not necessary.
Inline a function.
Clean up some whitespace.
routines are necessary to allow the use of certain types of hardware on
the alpha, particularly a Myrinet card.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu>
reported bug.
At using tcpdump for cs interface, tcpdump only dump packet which
src or dst MAC-address is cs interface. cs interface can't look up
packet between others.
Submitted by: MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
add support for Vibra16X, OPTi925, and bring in several assorted
fixes to the code and documentation.
Also present here are apm hooks so that laptops can properly
reconfigure the hardware after suspend (tested on the Libretto50).
Reviewed by: jordan
- Express various sizes in bytes, rather than Kbytes, in the video
mode and adapter information structures.
- Fill 0 in the linear buffer size field if the linear frame buffer
is not available.
- Remove SW_VESA_USER ioctl. It is still experimetal and was not meant
to be released.
- Fix missing cast operator.
- Correctly handle pointers returned by the VESA BIOS. The pointers
may point to the area either in the BIOS ROM or in the buffer supplied
by the caller.
- Set the destructive cursor at the right moment.
o Use the board id command to find out what kind of board
we're talking to. If we're talking to a board that is has
an ID that is shared between boards supported by the aha
driver and the bt driver, then use the bt's geometry
register to weed out the bt cards. Otherwise assume that we
support this card.
o Remove bt esetup command sending to the card. It seems to
wedge too many cards.
o Revert to doing a soft reset after an invalid command. This
change didn't fix anything, so I'm backing it out. The
whole issue of card resetting needs to be revisisted at some
point so that we can do it properly on all hardware.
o GC unused stuff in some places.
o Unlock mailbox interface if we have a new card. Before only newer cards
(B or newer) that had the BIOS disabled would probe. Cards with the
BIOS enabled would fail to probe in the mailbox initialization code.
o Increase the number of ccbs and sg to 17 from 16 to support 64k I/O
on a non page aligned boundary. Ideas for dynamic determination of this
value welcomed, as more of these are better.
o Took credit for this driver, even though I derived it from Justin's code.
Made sure that Justin's copyright from bt.c was preserved, along with
his name, since the error handling code is nearly identical. Add my
own, identical copyright. Point people to aha_isa.c.
Cards tested: 1542C and 1542CF. The B and CP might work now as well,
but logistical problems precluded me from testing them this evening
(if you have jumper settings for the B card, please send me private
mail).
- there were too many global variables (there still are :-).
- the data section was bloated by explicit initializations of static
variables to 0 (only fixed the recently changed ones).
- WRAPHIST() had silly parentheses around foo->bar.
- the comment about inline functions was stale.
- the comment about Userconfig presumes too much about the boot environment.
- `i' was reused confusingly in scioctl().
- the declaration of `butmap' used a deprecated K&R misfeature.
- the initializeation of `butmap' had an unnecessary line break.
- `unsigned char' was not consistently (mis)spelled as u_char.
- English was poor in a comment in videoio.c.
Submitted by: bde
- Handle pixel (raster text) mode properly.
- Clear screen and paint border right.
- Paint text attribute (colors).
- Fix off-by-one errors.
- Add some sanity checks.
- Fix some function prototypes.
- Add some comment lines.
- Define generic text mode numbers so that the user can just give
"80x25", "80x60", "132x25"..., rather than "VGA_xxx", to `vidcontrol'
to change the current video mode. `vidoio.c' and `vesa.c' will map
these numbers to real video mode numbers appropriate and available
with the given video hardware. I believe this will be useful to make
syscons more portable across archtectures.
Bump the lun field in the eata ccb to 5 bits. We still only
use 3 of them, but we may use the rest at a later date.
dpt_scsi.c:
Default to only 32 S/G segments.
Bzero our CCB array after allocation.
- ppbus was released before checking if still in disk_mode by vpoio and immio:
the microseq (in_disk_mode) was never executed. Fixed.
- nlptintr() renamed to nlpt_intr(). spltty() inserted in nlptintr() before
nlpt_intr() call
those extra ones yet, anyway.
In dpttimeout, expect that the controller will complete aborted CCBs through
the interrupt handler. This corrects a panic that was caused by completing
the same transaction twice during timeout recovery.
Honor the tag times types expressed by the user and pass them down to
the controller.
a timeout, we must remove the pending SCB from the disconnected list
or risk list corruption when our BDR request using the same SCB is placed
on the waiting list.
Eradicate some silly uses of u_int8_t that just serve to slow the code down.
+ Change some messages about CCB memory allocation
+ Turn a failure to DMA map all of a transaction due to lack of
ISP queue entries into a requeue operation (instead of the
case where it had been treated the same as a DMA too big
operation).
+ put back splsoftvm around bus_dmamap_load calls.
+ cleanup (and fix a glaring bug) in the and of the dma setup
routine. Also, the dma setup routines either return CMD_QUEUED
(for success) or CMD_COMPLETE (for failure) or CMD_EAGAIN
(for requeuing for resource shortage reasons).
Kazu writes:
The VESA support code requires vm86 support. Make sure your kernel
configuration file has the following line.
options "VM86"
If you want to statically link the VESA support code to the kernel,
add the following option to the kernel configuration file.
options "VESA"
The vidcontrol command now accepts the following video mode names:
VESA_132x25, VESA_132x43, VESA_132x50, VESA_132x60, VESA_800x600
The VESA_800x600 mode is a raster display mode. The 80x25 text will
be displayed on the 800x600 screen. Useful for some laptop computers.
vidcontrol accepts the new `-i <info>' option, where <info> must be
either `adapter' or `mode'. When the `-i adapter' option is given,
vidcontrol will print basic information (not much) on the video
adapter. When the `-i mode' option is specified, vidcontrol will
list video modes which are actually supported by the video adapter.
Submitted by: Kazutaka YOKOTA yokota@FreeBSD.ORG
Host ATM Research Platform (HARP), Network Computing Services, Inc.
This software was developed with the support of the Defense Advanced
Research Projects Agency (DARPA).
- Convert to CAM
- Use a new DMA based queuing and paging scheme
- Add preliminary target mode support
- Add support for the aic789X chips
- Take advantage of external SRAM on more controllers.
- Numerous bug fixes and performance improvements.
and use this when masking/unmasking interrupts.
Maintain a mapping from (iopaic number, int pin) tuple to irq number,
and use this when configuring devices and programming the ioapics.
Previous code assumed that irq number was equal to int pin number, and
that the ioapic number was 0.
Don't let an AP enter _cpu_switch before all local apics are initialized.
Removed Hauppauge EEPROM 0x10 detection as I think 0x10 should be a
PAL tuner, not NTSC.
Reinstated some Tuner Guesswork code from 1.27
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Added PR kern/7177 for SECAM Video Highway Xtreme with single crystal
PLL configuration submitted by Vsevolod Lobko <seva@alex-ua.com>.
In kernel configuration file add
options OVERRIDE_CARD=2
options OVERRIDE_TUNER=11
options BKTR_USE_PLL
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Normally the full 640x480 (768x576 PAL) image is grabbed. This ioctl
allows a smaller area from anywhere within the video image to be
grabbed, eg a 400x300 image from (50,10).
See restrictions in BT848SCAPAREA.
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Add a sysctl 'machdep.cs_recv_delay' to specify how long to wait after
receiving a packet in order to check for a subsequent (back-to-back)
packet. The cs8900 has a very small receive buffer, so this helps avoid
overflows at the cost of some extra CPU overhead.
Submitted by: Oleg Sharoiko <os@rsu.ru>, MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
for the Lite2 fix for always returning EIO in dead_read().
Cleaned up the cdevswitch initializers for all tty drivers.
Removed explicit calls to ttsetwater() from all (tty) drivers. ttsetwater()
is now called centrally for opens, not just for parameter changes.
The check for dropping unicast packets not sent to our ethernet
address is after the bpf tap, but not conditioned on it. All packets
received should get handed to bpf, and unicast packets not to us (mac)
should get dropped whether or not there is a bpf listener. I believe
that the common optimization that the interface is in hw promisc mode
iff there is a bpf listener is in general wrong, but more frequently
so on wavelans.
I think Max's fix makes bpf listeners not see unicast packets sent to
others, but I'm not sure.
One can argue that checking on MOD_ENAL is wrong, but the code only
drops packets that shouldn't be received. The correctness condition
is that it be run whenever unicast packets without our mac address can
be received.
PR: kern/7144
Submitted by: Greg Troxel <gdt@ir.bbn.com>
for 1 second's worth of input) and larger tty output buffers. The
interrupt-level buffers are still too small for speeds above 115200
bps (only a little too small for 230400 bps if RTS flow control is
enabled).
Don't call ttsetwater() explicitly in open(). It is now called for
the TTYDISC l_open() and should be static.
Don't attempt to register the cdevsw more than once.
description of DPT_SHUTDOWN_SLEEP in LINT. Didn't add timestamps
so that the (combined?) sleep interval can be printed as intended
in the original printf.
stability now. ALso modify /sys/conf/files, /sys/i386/conf/GENERIC
and /sys/i386/conf/LINT to add entries for the XL driver. Deactivate
support for the XL adapters in the vortex driver. LAstly, add a man
page.
(Also added an MLINKS entry for the ThunderLAN man page which I forgot
previously.)
of invariants to cyattach().
Fixed minor bugs:
- cyparam() returned without restoring the ipl in the error cases. This
was harmless because cyparam() is always called at spltty().
- one check for "rev. J or higher" actually checked for precisely rev. J.
swapped RTS/DTR). Merge the vendor's modification of the 2.2.6-release
version into -current for reference. Will be cleaned up in next commit.
Obtained from: ftp://ftp.cyclades.com/pub/cyclades/cyclom-y/freebsd/2.2.6/cyy226.tar.gz
was broken), 1.30 (COMPAT_43 option header was missing), 1.31 (DEVFS
option header was missing), 1.33 (garbage pointers were followed
in debugging code). Cosmetic changes from 1.27, 1.32, 1.36, 1.37.
Of course, the DEVFS code didn't even compile. Fixed. Not tested.
Forgotten by: brian
This file should not exist. It is the same as dgb.c except for lots of
renamed variables, about 250 lines removed, and only about 100 lines of
real differences.
instead of at compile time using ifdefs.
Use _swi_null instead of dummycamisr. CAM and dpt should call
register_swi() instead of hacking on ihandlers[] directly.
different size (on i386's with 64 bit longs). Cosmetic. Non-cosmetic
unportabilities were already hidden by using ntohl() to convert a
32-bit user DMA address to a long.
in ddb) which I broke by changing %8[l]x to %8p. Hacked the central
printf routine to not add an "0x" prefix for %p formats if the field
width is nonzero. The tables are still horribly misformatted on
64-bit machines.
Use %p instead of %8p to print pointers when the field width isn't
important.
chip.
It has been observed that the problem is most apparent:
a) in notebook computers,
b) and/or in the systems with C&T video chips.
Define the new configuration option SC_BAD_FLICKER in the kernel
configuration file to remove outb()/outw() calls in question.
interrupts which now defers them until the transmit queue if filled
up with completed buffers. This has two advantages: first, it reduces
the number of transmitter interrupts to just 1/120th of the rate
that they occured previously, and two, running down many buffers
at once has much improved cache effects.
- ppbus now supports PLIP via the if_plip driver
- ieee1284 infrastructure added, including parallel-port PnP
- port microsequencer added, for scripting the sort of port I/O
that is common with parallel devices without endless calls up and down
through the driver structure.
- improved bus ownership behaviour among the ppbus-using drivers.
- improved I/O chipset feature detection
The vpo driver is now implemented using the microsequencer, leading to
some performance improvements as well as providing an extensive example
of its use.
Reviewed by: msmith
Submitted by: Nicolas Souchu <Nicolas.Souchu@prism.uvsq.fr>
saver and splash screen can all work properly with syscons. Note that
the splash screen option (SC_SPLASH_SCREEN) does not work yet, as it
requires additional code from msmith.
- Reorganized the splash screen code to match the latest development
in this area.
- Delay screen switch in `switch_scr()' until the screen saver is
stopped, if one is running,
- Start the screen saver immediately, if any, when the `saver' key is
pressed. (There will be another commit for `kbdcontrol' to support
this keyword in the keymap file.)
- Do not always stop the screen saver when mouse-related ioctls
are called. Stop it only if the mouse is moved or buttons are
clicked; don't stop it if any other mouse ioctls are called.
2. Added provision to write userland screen savers. (Contact me if you
are interested in writing one.)
- Added CONS_IDLE, CONS_SAVERMODE, and CONS_SAVERSTART ioctls to
support userland screen savers.
3. Some code clean-ups.
the screen mode is changed even if another vty has larger size.
Reallocate the buffer only when the new screen size is larger than
the current cut buffer size.
When bell is of "quiet" types, the console won't ring (or flush)
if the ringing process is in a background vty.
PR: i386/2853
- Modify the escape sequence 'ESC[=%d;%dB' so that bell pitch and
duration are set in hertz and msecs by kbdcontrol(1).
There will be a corresponding kbdcontrol patch.
PR: bin/6037
Submitted by: Kouichi Hirabayashi (kh@eve.mogami-wire.co.jp)
and DSO_NOLABELS flags prevent searching for slices and labels
respectively. Current drivers don't set these flags. When
DSO_NOLABELS is set, the in-core label for the whole disk is cloned
to create an in-core label for each slice. This gives the correct
result (a good in-core label for the compatibility slice) if
DSO_ONESLICE is set or only one slice is found, but usually gives
broken labels otherwise, so DSO_ONESLICE should be set if DSO_NOLABELS
is set.
- Call isa_dmadone() whenever necessary to stop DMA and/or free bounce
buffers. Undead DMA corrupted the malloc freelist fairly consistently
in the following configuration: SLICE kernel, 2 floppy drives, no disk
in fd0, disk in fd1.
- Don't call fdc_reset() from fd_timeout(). Doing so gave an "extra"
interrupt which was usually misinterpreted as being for completion
of the next FDC command; the interrupt for completion of the next
FDC command was then usually misinterpreted... There were further
complications for interrupts latched by the soft-spl mechanism so
that they were delivered after all the h/w interrupts went away.
This caused at least wrong head settle delays and may be why the
FreeBSD floppy driver seems to munch floppies more than most floppy
drivers. The reset was unnecessary anyway in cases that didn't have
the bug described next, since is was repeated a little later for
the IOTIMEDOUT state. The state machine has complications to handle
resets correctly, so just use it.
- Don't call retrier() from fd_timeout(). The IOTIMEDOUT state needs
to be processed next, and it isn't valid to set to that state if
retrier() has aborted the current transfer. Doing so caused null
pointer panics after the previous bug was fixed.
Improved error handling:
- If an i/o is aborted, arrange to reset in the state machine before
doing the next i/o. New fdc flag for this. This fixes spurious
warnings and lengthy busy-waiting for the next i/o.
- Split STARTRECAL into RESETCOMPLETE and STARTRECAL and only check
for the results from reset if we actually reset. This fixes spurious
warnings for other paths to STARTRECAL. [Oops, it may break reset
handling for motor-off resets.]
Cleanups in fd_timeout():
- Renamed to fd_iotimeout() to make it clearer that it is only used
for i/o.
- Don't handle the bp == 0 case. This case can't happen for i/o.
- Don't check for controller-busy. We know it must be.
- Don't print anything. retrier() already prints too much for normal
errors.
- Fudge the state differently so that the state machine advances
fdc->retry and the status is invalid (perhaps this should fudge a
valid state like the one for WP).
- Style fixes.
several new features are added:
- support vc/vp shaping
- support pvc shadow interface
code cleanup:
- remove WMAYBE related code. ENI WMAYBE DMA doen't work.
- remove updating if_lastchange for every packet.
- BPF related code is moved to midway.c as it should be.
(bpfwrite should work if atm_pseudohdr and LLC/SNAP are
prepended.)
- BPF link type is changed to DLT_ATM_RFC1483.
BPF now understands only LLC/SNAP!! (because bpf can't
handle variable link header length.)
It is recommended to use LLC/SNAP instead of NULL
encapsulation for various reasons. (BPF, IPv6,
interoperability, etc.)
the code has been used for months in ALTQ and KAME IPv6.
OKed by phk long time ago.
Change the port address argument to pci_map_port to pci_port_t* which is
defined as u_int on the alpha, u_short on i386. This is a stopgap with a
hopefully limited lifetime.
Discussed with: Stefan Esser <se@freebsd.org>
controller reports a successful seek, it is very unlikely to report
seeking to a cylinder other than the one requested, but we check for
this, and botched the error handling for the requested_cylinder != 0
case. This error happened when the bug fixed in rev.1.52 of <sys/buf.h>
caused the head of buffer queue to change to one starting on a different
cylnder - the requested cylinder was found, but it wasn't what we
thought we requested. The fix is simply to arrange to reset the state
machine.
Corruption of the buffer queue seems to only have been a problem in the
floppy driver. Other drivers dequeue the head of the queue before doing
physical i/o on it, so the corruption at worse broke the elevator sort
order. Dequeueing breaks it anyway.
respectively. Most of the longs should probably have been
u_longs, but this changes is just to prevent warnings about
casts between pointers and integers of different sizes, not
to fix poorly chosen types.
interupt level events. This needs a lot of cleanup, but has been working
here for a month or two.. originally needed for CAM integration
but that hasn't happenned yet. The probing state machines for each
handler should be replaced by a more generic state-service. It's
still quite messy in there..
is the kernel part of my commits, the userlevel stuff will be done in
a separate commit. Add the ability to suspend as well as hibernate to
syscons. Create a new virtual key like hibernate for suspend. Update
apm_bios.h to define more apm bios goodies.
There is only cdevsw (which should be renamed in a later edit to deventry
or something). cdevsw contains the union of what were in both bdevsw an
cdevsw entries. The bdevsw[] table stiff exists and is a second pointer
to the cdevsw entry of the device. it's major is in d_bmaj rather than
d_maj. some cleanup still to happen (e.g. dsopen now gets two pointers
to the same cdevsw struct instead of one to a bdevsw and one to a cdevsw).
rawread()/rawwrite() went away as part of this though it's not strictly
the same patch, just that it involves all the same lines in the drivers.
cdroms no longer have write() entries (they did have rawwrite (?)).
tapes no longer have support for bdev operations.
Reviewed by: Eivind Eklund and Mike Smith
Changes suggested by eivind.
as the value in b_vp is often not really what you want.
(and needs to be frobbed). more cleanups will follow this.
Reviewed by: Bruce Evans <bde@freebsd.org>
data fifo is full, but the PCI input latch is not empty,
HDMAEN cannot be cleared. The fix used here is to attempt
to drain the data fifo until there is space for the input
latch to drain and HDMAEN de-asserts.
This is a 1 instruction fix, so it should have no performance
impact.
and don't depend on them being declared there. This will cause lots of
warnings for a few minutes until config is updated. Interrupt handlers
should never have been configured by config, and the machine generated
declarations get in the way of changing the arg type from int to void *.
over from the probe are now expected for incompatible UARTs that
deliver IRQs as a strobe (low) instead of a level (high).
Discard events on going-away devices too. Endless loops may have
been possible when an active pccard was removed.
Major changes to the generic device framework for FreeBSD/alpha:
* Eliminate bus_t and make it possible for all devices to have
attached children.
* Support dynamically extendable interfaces for drivers to replace
both the function pointers in driver_t and bus_ops_t (which has been
removed entirely. Two system defined interfaces have been defined,
'device' which is mandatory for all devices and 'bus' which is
recommended for all devices which support attached children.
* In addition, the alpha port defines two simple interfaces 'clock'
for attaching various real time clocks to the system and 'mcclock'
for the many different variations of mc146818 clocks which can be
attached to different alpha platforms. This eliminates two more
function pointer tables in favour of the generic method dispatch
system provided by the device framework.
Future device interfaces may include:
* cdev and bdev interfaces for devfs to use in replacement for specfs
and the fixed interfaces bdevsw and cdevsw.
* scsi interface to replace struct scsi_adapter (not sure how this
works in CAM but I imagine there is something similar there).
* various tailored interfaces for different bus types such as pci,
isa, pccard etc.
* Eliminate bus_t and make it possible for all devices to have
attached children.
* Support dynamically extendable interfaces for drivers to replace
both the function pointers in driver_t and bus_ops_t (which has been
removed entirely. Two system defined interfaces have been defined,
'device' which is mandatory for all devices and 'bus' which is
recommended for all devices which support attached children.
* In addition, the alpha port defines two simple interfaces 'clock'
for attaching various real time clocks to the system and 'mcclock'
for the many different variations of mc146818 clocks which can be
attached to different alpha platforms. This eliminates two more
function pointer tables in favour of the generic method dispatch
system provided by the device framework.
Future device interfaces may include:
* cdev and bdev interfaces for devfs to use in replacement for specfs
and the fixed interfaces bdevsw and cdevsw.
* scsi interface to replace struct scsi_adapter (not sure how this
works in CAM but I imagine there is something similar there).
* various tailored interfaces for different bus types such as pci,
isa, pccard etc.
- connector selection values (should fix aui/bnc),
- non-shifting version of crc calculation using a table,
- interrupt mask adjustments,
- add some brackets where a #ifdef could break an if(),
- don't reset the card unless it's up.
work in progress and has never booted a real machine. Initial
development and testing was done using SimOS (see
http://simos.stanford.edu for details). On the SimOS simulator, this
port successfully reaches single-user mode and has been tested with
loads as high as one copy of /bin/ls :-).
Obtained from: partly from NetBSD/alpha
or unsigned int (this doesn't change the struct layout, size or
alignment in any of the files changed in this commit, at least for
gcc on i386's. Using bitfields of type u_char may affect size and
alignment but not packing)).
FreeBSD/alpha. The most significant item is to change the command
argument to ioctl functions from int to u_long. This change brings us
inline with various other BSD versions. Driver writers may like to
use (__FreeBSD_version == 300003) to detect this change.
The prototype FreeBSD/alpha machdep will follow in a couple of days
time.
miscconfigured case) if the port is the console. This fixes several
bugs:
- if all sioprobe()s failed, then the console driver followed null
pointers in cdevsw[].
- if the sioprobe() for the console failed but another sioprobe()
succeeded, then init hung early when the console couldn't be
opened.
- it was silly for the console to not be there after printing boot
messages on it.
Bugs introduced by this are hopefully no worse than old ones caused
by forcing the success of the `cn' level probe.
Only complain about an irq mismatch in the probe if the configured
irq doesn't become active, and then print the bitmap of irqs that
became active (including clock irqs) instead of just the first
(not including clock irqs).
Bugs reported by: msmith
a test of the irq number, and made failure of this test non-fatal.
Removed related unused complications for the APIC_IO case. Removed the
no-test3 flag.
Deverbosified the failure messages for the other tests. Removed the
per-port verbose flag - just use the general verbose flag.
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
in the kernel config file makes the driver's video_open() function
select PAL rather than NTSC. This fixed all the hangs on my
Dual Crystal card when using a PAL video signal.
As a result, you can loose the tsleep (of 2 seconds - now 0.25!!)
which I previously added. (Unless someone else wanted the 0.25
second tsleep).
submitted ioctl to clear the video buffer
prior to starting video capture
Amancio : clean up yuv12 so that it does not
affect rgb capture. Basically, fxtv after
capturing in yuv12 mode , switching to rgb
would cause the video capture to be too bright.
1.32 disable inverse gamma function for rgb and yuv
capture. fixed meteor brightness ioctl it now
converts the brightness value from unsigned to
signed.
1.33 added sysctl: hw.bt848.tuner, hw.bt848.reverse_mute,
hw.bt848.card
card takes a value from 0 to bt848_max_card
tuner takes a value from 0 to bt848_max_tuner
reverse_mute : 0 no effect, 1 reverse tuner
mute function some tuners are wired reversed :(
but doesn't do much of anything with it. I added it to siopnp_ids[]
and it was found and recognized as a serial port.
PR: 6605
Reviewed by: phk
Submitted by: Dave Marquardt <marquard@zilker.net>
[__]inline is only used to bloat the code here. It gives a separate copy
of all the strings for each time this header is included...
Fixed misuse of __P(()).
- pessimized i/o port types.
- other pessimized types.
- Don't use DEBUG (causes LINT warnings). Use DGB_DEBUG instead.
- commented out code.
- cloned code that doesn't apply ("Smarts" is for the cy driver only).
Submitted by: bde
dereference uninitialized pointers.
o Fix DEVFS permissions
o Fix DEVFS minor numbers
o Add initial & lock devices for cua device.
o Fix permissions in line with sio.
This code will be turned on with the TWO options
DEVFS and SLICE. (see LINT)
Two labels PRE_DEVFS_SLICE and POST_DEVFS_SLICE will deliniate these changes.
/dev will be automatically mounted by init (thanks phk)
on bootup. See /sys/dev/slice/slice.4 for more info.
All code should act the same without these options enabled.
Mike Smith, Poul Henning Kamp, Soeren, and a few dozen others
This code does not support the following:
bad144 handling.
Persistance. (My head is still hurting from the last time we discussed this)
ATAPI flopies are not handled by the SLICE code yet.
When this code is running, all major numbers are arbitrary and COULD
be dynamically assigned. (this is not done, for POLA only)
Minor numbers for disk slices ARE arbitray and dynamically assigned.
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Roger Hardiman <roger@cs.strath.ac.uk> :
Revised autodetection code to correctly handle both
old and new VideoLogic Captivator PCI cards.
Added tsleep of 2 seconds to initialistion code for PAL users.
Corrected clock selection code on format change.
--- Amancio
- Set the correct value scp->font_size in init_scp().
- Set scp->font_size to FONT_NONE for VGA_MODEX.
Interim fix for a font problem:
- A kludge to display the correct font on some video cards.
We should be able to load multiple fonts to the VGA plane #2 and switch
between fonts by setting the font select register in the VGA sequencer.
It appears that the current code isn't functioning as expected on
some VGA cards (I have reports on Millenium and Mach64 cards). This is
either a bug in syscons or a hardware compatibility problem ;-<
This kludge will always load only one font set at a time and always use
the font page #0 on the plane #2. It is an interim kludge until
we find the exact cause and solution.
Small adjustment for mouse cursor handling:
- Turn off the mouse cursor early when changing video modes.
Video mode switch fixes:
- Stop the screen saver when changing video modes.
- Enclose the critical section with a pair of spltty()/splx().
- A kludge to prevent scrn_update() from accessing video memory in less-
critical sections in video mode change; artificially turn on the
UNKNOWN_MODE flag.
PR: bin/5899, bin/5907
Tested by: ache and a couple of users
OKed by: sos
* Figure out UTC relative to boottime. Four new functions provide
time relative to boottime.
* move "runtime" into struct proc. This helps fix the calcru()
problem in SMP.
* kill mono_time.
* add timespec{add|sub|cmp} macros to time.h. (XXX: These may change!)
* nanosleep, select & poll takes long sleeps one day at a time
Reviewed by: bde
Tested by: ache and others
- Attempt to handle PCI devices where the interrupt is
an ISA/EISA interrupt according to the mp table.
- Attempt to handle multiple IO APIC pins connected to
the same PCI or ISA/EISA interrupt source. Print a
warning if this happens, since performance is suboptimal.
This workaround is only used for PCI devices.
With these two workarounds, the -SMP kernel is capable of running on
my Asus P/I-P65UP5 motherboard when version 1.4 of the MP table is disabled.
- Implement proper EISA probing.
- Better support for the new transputer based host cards.
- use standard termios settings, one can use the intial/lock devices.
- use a simple bcopy since some cards/systems apparently don't support
32 bit accesses.
- hard reset and halt host card CPU prior to download in case of a soft
restart.
- recognize new remote module types (ASIC vs. CD1400 based)
- a number of cosmetic changes (my fault, not Nick's)
Submitted by: Nick Sayer <nsayer@quack.kfu.com>
Fixed pedantic semantics errors (in ANSI C, static arrays must have
a size, and static objects should be consistently declared as static
unless you know more than anyone should have to know about the
linkage rules).
select/poll and DEVFS changes, which are limited to an include/define
in sound.h and the actual select/poll implementation in sound.c
[ This commit is blind, but the code is similar enough that there will
hopefully be no problems. ]
The differences Terrys patch and this patch are:
* Remove a lot of un-needed comments.
* Don't put l_hotchar at the front of stuct linesw, there is no need to.
* Use the #defines for the hotchar in the SLIP and PPP line disciplines
this using option "-b" to the boot blocks. It is smartest to compile
a font into your kernel (See LINT), but not mandatory, but apart from
the cursor you will see nothing on the screen until you load a font.
This mode allows XF86_VGA16 to run in 800x600 mode on otherwise unsupported
graphics hardware.
A number of buglets in the cursor handling in syscons may become
visible this way.
mode switch in ioctl.
Possibly related to PR: kern/4271
- A kludge: initialize scp->xpixel and ypixel even in the text mode.
If the console enters the `unknown' graphics mode via the ioctl KDSETMODE
(KD_GRAPHICS), these fields are not set (because syscons cannot know
the correct values), but set_mouse_pos() need to refer to these field
to adjust the mouse position.
- Turn off MOUSE_VISIBLE when switching video mode by ioctl.
- another new option: SC_MOUSE_CHAR
Define the first character code of four consecutive codes to be used for
the mouse cursor. Default codes are 0xd0 through 0xd3. Beware that
if you decide to use any codes outside the range of 0xc0-0xdf,
the mouse cursor may not look good, because of the way VGA displays
characters in 9-dot-wide character cells.
Requested by several people.
(This patch was tested by a person who recently reported, in the -current
ML, a page fault problem in the kernel (draw_mouse_iamge()) after
X server shutdown. The patch cured his problem.)
Don't touch/update the screen while manipulating font data.
Possibly related to PR: kern/4271
- Set up VGA in alphanumeric mode rather than graphics mode when
loading font into video memory. This will drastically reduce flicker.
PR: bin/2977
- Set up scp->font_size properly during video mode switch caused by
ioctl.
separate routine: scupdate() called from scrn_timer().
- Make sure that the screen is updated for the low-level console
routines sccngetc() and sccncheckc(). A new routine, sccnupdate(),
is introduced and will call scupdate() above.
Requested by: bde and msmith
OKed by: sos
from the low-level console routines sccngetc() and sccncheckc().
Submitted by: bde (a long time ago)
- Don't try to ring bell and immediately return from do_bell() while
device probe is in progress at boot time; the timeout queue is not
functional yet.
PR: kern/2424
- Stop running the screen saver after panic() is called: check
if `panicstr' is non-NULL during scrn_timer().
PR: kern/5314
- A new option: SC_DISABLE_REBOOT
The reboot key (usually Ctl-Alt-Del) will be ignored if this option
is defined. You may still have the reboot key defined in the keymap and
it won't cause error when the keymap is loaded, but it will be quietly
treated as nop.
OKed by: sos
1. Takeshi Ohashi <ohashi@atohasi.mickey.ai.kyutech.ac.jp> submitted
code to support bktr_read . /usr/src/share/examples/rgb24.c now works 8)
2. Flemming Jacobsen <fj@schizo.dk.tfs.com> submitted code to support
radio available with in some bt848 based cards;additionally, wrote
code to correctly recognized his bt848 card.
3. Roger Hardiman <roger@cs.strath.ac.uk> submitted various fixes to smooth
out the microcode and made all modes consistent.
4. Added supported for yuv12 so we know can capture raw streams and feed it
to mpeg_encoder . The upshot is that we can now mpeg encode more and save
nearly 100 percent of the disk requirements previously for programs such
as fxtv first save the raw video image to disk then converted to a
format suitable for mpeg_encode.
a BSD4.4Lite1 feature, not a FreeBSD feature. <sys/ioctl.h> is a
compatibility misfeature.
Moved NPCI ifdef. This file didn't compile if NPCI <= 0. It shouldn't
be configured in that case, but it is easy to support (mis)configuration
of drivers without buses by generating null objects, and many drivers
do it.
Removed unused includes.
This introduce an xxxFS_BOOT for each of the rootable filesystems.
(Presently not required, but encouraged to allow a smooth move of option *FS
to opt_dontuse.h later.)
LFS is temporarily disabled, and will be re-enabled tomorrow.
so that existing programs which were compiled before the introduction
of the new mouse code and use these ioctls will run unmodified.
Suggested by msmith.
not quite correct, because the Makefiles in lkm/syscons don't set up the
`machine' symlink, but other, more volatile headers in <machine> are
already used.
(accent_key + space does still print the accent letter too, as in
the previous commit.)
Requested by a couple of users.
- Clear the accent flag when the next_screen key is pressed.
- Added some comment lines regarding accent key processing.
This will not make any of object files that LINT create change; there
might be differences with INET disabled, but hardly anything compiled
before without INET anyway. Now the 'obvious' things will give a
proper error if compiled without inet - ipx_ip, ipfw, tcp_debug. The
only thing that _should_ work (but can't be made to compile reasonably
easily) is sppp :-(
This commit move struct arpcom from <netinet/if_ether.h> to
<net/if_arp.h>.
- IIR_TXRDY is never off even if reading a IIR register.
- Know as PIAFS "Palido 321S", "DC-*S" oemed by Sharp corp.
2. Omiting a restrict probing if it's already probed by pccardd.
Note: Define a new id_flags as follows
0x40000 - NO PROBE (Already probed as serial)
0x80000 - Has a bogus IIR_TXRDY register
Sato Junichi <junichi@astec.co.jp>
Nrihiro Kumagai <kuma@slab.tnr.sharp.co.jp>
Hirao Tetsuya <ai.cs.fujitsu.co.jp>
Toshiharu Asai <asai@mbc.infoshere.or.jp>
Shin'ya Kumabuchi <kumabu@t3.rim.or.jp>
Freebsd-users-jp@jp.freebsd.orgbsd-nomads@ai.cs.fujitsu.co.jp
With a keymap with accent key definitions loaded to syscons, you press
an accent key followed by a regular letter key to produce an accented
letter. Press an accent key followed by the space bar to get the
accent letter itself.
Code is based on the ideas and work by jmrueda@diatel.upm.es and
totii@est.is.
PR: i386/4016
console.h
- Defined structures and constants for accent (dead) keys.
syscons.c, kbdtables.h
- When an accent key is pressed, set the corresponding index to
`accents'. If the next key is the space key, produce the accent char
itself. Otherwise search the accent key map entry, indexed by
`accents', for a matching pair of a regular char and an accented char.
- Added ioctl functions to set and get the accent key map (PIO_DEADKEYMAP
and GIO_DEADKEYMAP).
Submitted by: Jonathan Hanna <pangolin@rogers.wave.ca>
The patch is for a Hauppauge Win/TV dbx with FM. I still need to
config OVERRIDE_TUNER, but it works nicely.
necessary to call it when the tty layer's output state has not been
changed, but siostop() sometimes changes the TS_BUSY state and then
calls comstart() mainly for its side effect of calling ttwwakeup().
need to do it directly, since ttwwakeup() is always called just before
returning from rpstart(). The brokenness was waking up the wrong address
after clearing TS_SO_OLOWAT. It's not clear how processes waiting for
output to drain below low water ever got woken up.
Found by: when I fixed longstanding warts in output watermark
handling, this was the only driver that knew too much
(anything) about the watermarks
The #ifdef IPXIP in netipx/ipx_if.h is OK (used from ipx_usrreq.c and
ifconfig.c only).
I also fixed a typo IPXTUNNEL -> IPTUNNEL (and #ifdef'ed out the code
inside, as it never could have compiled - doh.)
MS IntelliMouse, Kensington Thinking Mouse, Genius NetScroll,
Genius NetMouse, Genius NetMouse Pro, ALPS GlidePoint, ASCII
MieMouse, Logitech MouseMan+, FirstMouse+
- The `psm' driver is made to recognize various models of PS/2 mice
and enable their extra features so that their additional buttons and
wheel/roller are recognized. The name of the detected model will be
printed at boot time.
- A set of new ioctl functions are added to the `psm', `mse' and
`sysmouse' drivers so that the userland program (such as the X server)
can query device information and change driver settings.
- The wheel/roller movement is handled as the `Z' axis movement by the
mouse drivers and the moused daemon. The Z axis movement may be mapped
to another axis movement or buttons.
- The mouse drivers support a new, standard mouse data format,
MOUSE_PROTO_SYSMOUSE format which can encode x, y, and x axis movement
and up to 10 buttons.
/sys/i386/include/mouse.h
- Added some fields to `mousestatus_t' to store Z axis movement
and flag bits.
- Added the field `model' to `mousehw_t' to store mouse model code.
Defined model codes.
- Extended `mousemode_t'.
- Added new protocols and some constants for them.
- Added new ioctl functions and structures.
- Removed obsolete ioctl definitions.
/sys/i386/include/console.h
- Added `dz' field to the structure `mouse_data' to pass Z axis movement
to `syscons/sysmouse'.
- Removed LEFT_BUTTON, MIDDLE_BUTTON and RIGHT_BUTTON. Use button bits
defined in `mouse.h' instead.
/sys/i386/isa/psm.c
- Added a set of functions to detect various mice which have additional
features (wheel and buttons) unavailable in the standard PS/2 mouse.
- Refined existing ioctl functions and added new ones. Most important
of all is MOUSE_SETLEVEL which manipulates the output level of the driver.
While the output level remains zero, the output from the `psm' driver is
in the standard PS/2 mouse format (three bytes long). When the level
is set to one, the `psm' driver will send data in the extended format.
At the level two the driver uses the format which is native to the
connected mouse is used. (Meaning that the output from the device is
passed to the caller as is, unmodified.) The `psm' driver will pass
such extended data format as is to the caller if the output level is
two, but emulates the standard format if the output level is zero.
- Added kernel configuration flags to set initial resolution
(PSM_CONFIG_RESOLUTION) and acceleration (PSM_CONFIG_ACCEL).
- Removed the compile options PSM_ACCEL, PSM_CHECKSYNC and PSM_EMULATION.
Acceleration ratio is now specified by the kernel configuration flags
stated above. Sync check logic is refined and now standard.
The sync check can be turned off by the new kernel configuration flags
PSM_CONFIG_NOCHECKSYNC (0x100). PSM_EMULATION has been of little use.
- Summer clean up :-) Removed unused code and obsolete comments.
/sys/i386/isa/mse.c
- Created mseioctl() to deal with ioctl functions MOUSE_XXXX.
Most importantly, the MOUSE_SETLEVEL ioctl will change the
output format from the 5 byte format to the new, extended format
so that the caller can take advantage of Z axis movement and additional
buttons.
- Use constants defined in `mouse.h' rather than magic numbers.
/sys/i386/isa/syscons.c
- Changed scioctl() to reflect the new `console.h' and some of the new
ioctls defined in `mouse.h'. Most importantly, the MOUSE_SETLEVEL
ioctl will change the `sysmouse' output format from the MouseSystems
5 byte format to the new, extended format so that the caller can
take advantage of Z axis movement and additional buttons.
- Added support for double/triple click actions of the left button and
single click action of the right button in the virtual console. The
left button double click will select a word under the mouse pointer.
The triple click will select a line and the single click of the right
button will extend the selected region to the current position of
the mouse pointer. This will make the cut/paste support more compatible
with xterm.
/sys/i386/isa/kbdio.h
- Added PSM_INTELLI_ID.
checking the BIOS video mode paramter table. Now syscons uses the
parameter table even if some bits in the table are different from the
current VGA register settings.
Even if comp_vgaregs() finds that the BIOS video parameter table looks
totally unfamiliar to it, syscons allows the user to change the
current video mode to some modes which are based on the VGA 80x25
mode. They are VGA 80x30, VGA 80x50, VGA 80x60. In this case the user
will be warned, during boot, that video mode switching is only
paritally supported on his machine.
PR: bin/4477
Fixed nonblocking mode. It was per-device instead of per-file.
Don't depend on gcc's misfeature of rewriting char args in old-style
function definitions to match wrong prototypes. Break K&R1 support
to fix this quickly.
actually offsets, they are offsets scaled by dividing by 2^cy_align.
I use different values for cy_align since the -current values are
unnaturally scaled, so I need different offsets, and the wrong
offsets got committed.
Reported by: nnd@itfs.nsk.su (N.Dudorov)
2) Fix temporal decimation, disable it when
doing CAP_SINGLEs, and in dual-field capture, don't
capture fields for different frames
Submitted by: Luigi Rizzo & Randall Hopper
changes:
o rip the old select from his distribution to prevent extra pollution
o the code now uses audio dma, helps reduce clicks
o improved card support, should work in full duplex on sb16 cards
o add better voxware ioctl support pointed out by Joao Carlos Mendes
Luis <jonny@coppe.ufrj.br>
o remove an unused file that I included for more complete history
o and MANY other changes
I have personally tested this code with a CS4237 based card and an AWE32
(non-PnP). Both cards worked fine in 8bit and 16bit mode.
This make the Miro PCTV work for me, including audio, and should
hopefully fix the other audio problems some people have been having.
Reviewed by: ahasty & Luigi Rizzo (freebsd-multimedia)
to define it by including <sys/kernel.h>. That broke PC-CARD
support for this driver, producing the dreaded "device allocation
failed" message. Surprisingly, the missing include caused only
two compiler warnings. The compilation still "succeeded" anyway.
usage at 0x100. Quoted Justin's quotation from the manual as well, to
explain the technical background.
PR: kern/4559
Submitted by: Stephen J. Roznowski <sjr@home.net>
use a Linker Set. Note, if a driver is loaded as an LKM if will have
to use the function call, but since none of the existing drivers
are loadable, this made things cleaner and boot messages nicer.
Obtained from: PAO-970616
flicker won't occur when set_border() is called.
- Properly restore the border color when switching virtual consoles.
Pointed out by: tony@dell.com
OKed by: sos
screen size was changed while the screen saver was inactive. Adjust
the positions of the daemon and the text and clip them accordingly
each time.
- Don't call set_border() too often. Some video chip may produce
flicker.
Pointed out by tony@dell.com
- Don't fill the entire screen with blank char every time the saver is
called. Blank only the part of the screen where the daemon and the
text was previously printed.
* Kill individual drivers 'suspend' routines, since there's no simple/safe
way to suspend/resume a card w/out going through the complete probe
at initialization time.
* Default to using the apm_pccard_resume sysctl code, which basically
pretends the card was removed, and then re-inserted. Suspend/resume
is now 'emulated' with a fake insert/removal. (Hence we no longer
need the driver-specific suspend routines.)
follow.
* Rename/reorder all of the pccard structures, change many of the member
names to be descriptive, and follow more closely other 'bus' drivers
naming schemes.
* Rename a bunch of parameter and local variable names to be more
consistant in the code.
* Renamed the PCCARD 'crd' device to be the 'card' device
* KNF and make the code consistant where it was obvious.
* ifdef'd out some unused code
check the value and caused kernel panic when a large value was given.
- Move the configuration option SC_HISTORY_SIZE from syscons.h to
syscons.c.
- Define the maximum total number of history lines of all consoles.
It is SC_HISTORY_SIZE*MAXCONS or 1000*MAXCONS; whichever is larger.
CONS_HISTORY will allow the user to set the history size up to
SC_HISTORY_SIZE unconditionally (or the current height of the console
if it is larger than SC_HISTORY_SIZE). If the user requests a larger
buffer, it will be granted only if the total number of all allocated
history lines and the requested number of lines won't exceed the maximum.
- Don't free the previous history buffer and leave the history buffer
pointer holding a invalid pointer. Set the pointer to NULL first, then
free the buffer.
PR: bin/4592
floppy drive #0, regardless of what the CMOS says. This is intended
as a bandaid for those plagued with Compaq's idea to not announce the
floppy drive on their `Aero' notebook.
Using the device flags is not very nice (in particular since they
aren't per-drive but per-controller), but still looks a lot better to
me than the disgusting guesswork hack that was recently posted to
-hackers.
Doc update will follow shortly.
a change that might have an effect on the problems some have seen
with older chips, it looks like the driver may have mistakenly thought
there was an SIA when there isn't.
Distribute all but the most fundamental malloc types. This time I also
remembered the trick to making things static: Put "static" in front of
them.
A couple of finer points by: bde
This driver includes the following patches submitted by:
1.0 Hideyuki Suzuki <hideyuki@sat.t.u-tokyo.ac.jp>
Japanese Cable support
2.0 Keith Sklower <sklower@CS.Berkeley.EDU>
Minor update to the BSDI section so it compiles cleanly on BSDI
3.0 Joao Carlos Mendes Luis <jonny@coppe.ufrj.br>
ioctl interface to select video format , NTSC, PAL, etc...
savers are also modified so that they behave in the same way as the
blank saver on MDA and CGA, although it's not the way these screen
savers are supposed to work, but fading monitor and tickling green
monitor cannot be done on MDA and CGA, AFAIK. So, this is the second
best solution.
As of this change, the current state of support of screen savers is
summarized in the following table.
MDA CGA EGA VGA
blank OK OK NA OK
daemon OK OK OK OK
fade * * NA OK
green * * NA OK
snake OK OK OK OK
star OK OK OK OK
OK: works
NA: doesn't work, the module cannot be loaded for this adapter.
*: behave the same way as the blank saver.
As you can see, EGA is left out for now. But, we can do no better, as
EGA registers cannot be read...
Reviewed by: sos
shown to be harmful in that it results in the card not being detected
properly on warmboot due to the station address failing to be read
correctly from the NVRAM.
much like the scancode mode.
However the keys that (for no good reason) returns extension codes
etc, are translated into singlebyte codes.
Needed by libvgl. This makes life ALOT easier, also the XFree86
folks could use this.
overruns (not that it was a problem, but it could be):
1) Doubled the number of receive buffers in the DMA chain to 64.
2) Do packet receive processing before transmit in the interrupt routine.
if it is in 10Mbps mode and gets certain types of garbage prior to
the packet header. The work-around involves reprogramming the
multicast filter if nothing is received in some number of seconds
(currently set at 15). As a side effect, implemented complete support
for multicasting rather than the previous 'receive all multicasts'
hack, since we now have the ability to program the filter table.
Fixed a serious bug which crept in with the timeout() changes;
the cookie was only saved on the first timeout() call in fxp_init()
and wasn't updated in the most common place in fxp_stats_update()
when the timeout was rescheduled. This bug would have resulted in
an eventual panic if fxp_stop() was called (which happens when any
interface flags are changed, for example).
Fixed a bug in Alpha support that would have caused the TxCB
descriptor chain to span a page boundry, causing serious problems
if the pages didn't happen to be contiguous.
Removed some gratuitous bit masking that was left over from an
older implementation.
Fixed a bug where too much was copied from the configuration
template, spilling over into memory that followed it.
Fixed handling of if_timer...it was cleared too early in some cases.
operands that are set during seqeuncer program download instead of at
assembly time.
Convert the sequencer code to use" downloaded constants" for four run time
constants that vary depending on the board type. This frees up 4 bytes
of sequencer scratch ram space where these constants used to be stored and
also removes the additional instructions required to load their values
into the accumulator prior to using them.
Remove the REJBYTE sram variable. The host driver can just as easly
read the accumulator to get this value.
The scratch ram savings is important as the old code used to clober the
SCSICONF register on 274X cards which sits near the top of scratch ram
space. The SCSICONF register controls bus termination, and clobbering
it is not a good thing. Now we have 4 bytes to spare.
This should fix the reported problems with cards that don't have devices
attached to them failing with a stream of "Somone reset bus X" messages.
Doug Ledford determined the cause of the problem, fixes by me.
1. Clustered I/O is switched by the MNT_NOCLUSTERR and MNT_NOCLUSTERW
bits of the mnt_flag. The sysctl variables, vfs.foo.doclusterread
and vfs.foo.doclusterwrite are deleted. Only mount option can
control clustered I/O from userland.
2. When foofs_mount mounts block device, foofs_mount checks D_CLUSTERR
and D_CLUSTERW bits of the d_flags member in the block device switch
table. If D_NOCLUSTERR / D_NOCLUSTERW are set, MNT_NOCLUSTERR /
MNT_NOCLUSTERW bits will be set. In this case, MNT_NOCLUSTERR and
MNT_NOCLUSTERW cannot be cleared from userland.
3. Vnode driver disables both clustered read and write.
4. Union filesystem disables clutered write.
Reviewed by: bde
- some addition of comments (for readability)
- iso-2022 G0 designation support. This does almost nothing. Just for
avoiding garbled screen when got "ESC ( B".
(how about G1/2/3 designation? I'm not sure)
the normal CS4326 except that it's had it's ID's tweaked for some reason)
Also mark the device as alive in the attach routine so that the pnp system
doesn't think the attach failed.
of multiple PCI IDE controllers(Dyson), and some updates and cleanups from
John Hood, who originally made our IDE DMA stuff work :-).
I have run tests with 7 IDE drives connected to my system, all in DMA
mode, with no errors. Modulo any bugs, this stuff makes IDE look
really good (within it's limitations.)
Submitted by: John Hood <cgull@smoke.marlboro.vt.us>
rather than extracting the diff from Mark's patch, but it turns out that
I was freeing one allocation twice due to a previous cut/paste braino.
My botch, not Mark's.
Pointed out by: Mark Valentine <mv@pobox.com>
internal modems. Currently detects a USR modem, and a couple Supra
modems... vendor id's for sio capabile cards welcomed...
document new option EXTRA_SIO that will increase sio's internal data
structures to support X more serial ports... these are used by the
PnP part of sio for attaching... If you don't have it specified, it
will default to 2... This is defaulted to 0 if you don't have PnP
compiled into your kernel...
also document that if you set the PnP flags (pnp x flags y) to 0x1 that
the modem will be refused to be recognized by the sio driver... this
is for people that want the traditional isa driver to probe and attach
the modem... (for keeping legacy sio numbering)
number of dma overruns/underruns for systems under heavy dma load.
As a side effect, broken enhanced floppy controllers that sometimes
don't detect dma overruns/underruns will give less errors.
Reviewed by: j@uriah.heep.sax.de (J Wunsch)
Hide the bogus FDC ``chip type'' display behind a (mostly) undocumented
option, since people started to trust the bogus claim. Once we're going
to handle 2.88 MB controllers, we have to redo the chip detection, by
now just leave it hidden.
large (over 4KB) softc struct. The descriptor array is accessed by
busmaster dma and must be physically contiguous in memory. malloc() of
a block greater than a page is only virtually contiguous, and not
necessarily physically contigious.
contigmalloc() could do this, but that is a bit on the overkill side.
I'm not sure of the origins of the problem report and diagnosis, I learned
of the problem via mail forwarded from Jim Shankland <jas@flyingfox.com>.
Jim said that Matt Thomas's workaround was to reduce the number of
transmit descriptors from 128 to 32, but I was concerned that it might
cost performance. Anyway, this change is my fault, not Jim's. :-)
Reviewed by: davidg
delay that without this the performance is unacceptable. The 83C690,
83C790, and 83C795 chips which this affects are all designed to work
with 0 waitstates in 16bit mode.
Also cleaned up the toggling of 16bit access mode that occurs during
normal operation; the previous code may not have done the right thing
in all cases.
size in terms of lines (instead of bytes). When changing video mode
in ioctl SW_XXX commands, syscons checks scp->history_size and
allocate a history buffer at least as large as the new screen size.
(This was unnecessary before, because HISTORY_SIZE was as large as 100
lines and this is bigger than the maximum screen size: 60 lines).
Similar adjustment is done in ioctl CONS_HISTORY command too.
PR: kern/4169
Reviewed by: sos
Includers of this file apparently didn't know that <sys/queue.h>
was a prerequisite and include a semi-random collection headers
until one happened to include it.
and hardware.
There is now another simple_lock around clock data/hardware accesses in
clock.c and microtime.s. It is my belief that this is the only area
sio/cy might stumble into during an unblocked INTerrupt. Thus I separated
the sio/cy code from the generic disable_intr()/enable_intr() routines.
Controlled by smptests.h: USE_COMLOCK, ON by default.
Add a simplelock to deal with disable_intr()/enable_intr() as used in UP kernel.
UP kernel expects that this is enough to guarantee exclusive access to
regions of code bracketed by these 2 functions.
Add a simplelock to bracket clock accesses in clock.c: clock_lock.
Help from: Bruce Evans <bde@zeta.org.au>
Remove unused headers.
Remove all but one instance of the device base name.
Prototype some local static functions.
Consistently reference the softc structure as "sc" rather than "lpt".
Prompted-by: bde
arg of type u_short (just write the function in ANSI C like most
other functions in this file instead of fixing the interface or
depending on a gcc feature).
I have no way of testing this one, first SMP/cy user please let me know...
It is my belief that sio and cy are the only FAST_INTR() ISRs. If this
is a bad assumption please educate me.
Several new fine-grained locks.
New FAST_INTR() methods:
- separate simplelock for FAST_INTR, no more giant lock.
- FAST_INTR()s no longer checks ipending on way out of ISR.
sio made MP-safe (I hope).
- interrupt-driven printing now works (nlpt)
- Rearrangement of bus-related functions into ppb_base/ppbconf
- Addition of ieee1284 interface functions, preliminary parallel-port
PnP support
Submitted by: Nicolas Souchu <Nicolas.Souchu@prism.uvsq.fr>
entry to the QOUTFIFO when it is full. This should eliminate the
"Timed out while idle" problems that many have reported.
In truth, this is somewhat of a hack. Although are interrupt latency is
low enough that we should be able to always service the queue in time,
since each entry must be passed up to the higher SCSI layer for what can
be a large amount of processing (perhaps even resulting in a new command
being queued) with interrupts disabled, we need this mechanism to avoid
overflow. In the future, these additional tasks will be offloaded to a
software interrupt handler which should make this hack unnecessary.
Add support for MODEX 320x240x256color with "unchained" adressing, giving
access to all 256K on all VGA's, those with that much memory that is :)
Also make sysmouse use the right resolution in graphics modes.
facilitate the new saver loading/unloading notification interface
in syscons.
daemon_saver:
- M_NOWAIT was wrong, since NULL returns are not handled. Just use
M_WAITOK.
- use `ostype' instead of hard-coded "FreeBSD". Now there is no more
hard-coded string! (But, who will run this screen saver on other
OS?!)
- put macros and data declarations in a consistent order.
- -DDEAMON_ONLY and -DSHOW_HOSTNAME options added in the previous commit
are removed. Options of this kind can go stale and no one notices
because no one uses them. DEAMON_ONLY is just removed. SHOW_HOSTNAME
is made default.
snake_saver:
- use `ostype' and `osrelease' as in the daemon saver. The string changes
slightly - there was a hyphen after "FreeBSD"; now there is a space.
(It is consistent with uname -a, like the daemon server already is.)
all screen savers:
- Use the new add_scrn_saver()/remove_scrn_saver() in syscons.c
to declare loading/unloading of a screen saver. Removed reference
to `current_saver' and the variable `old_saver' as they are not
necessary anymore.
- The blank, fade and green screen savers manipulate VGA registers.
Module loading should fail for non-VGA cards.
- `scrn_blanked' is consistently treated as a number/counter rather
than boolean.
- Some savers touch `scp->start' and `scp->end' to force entire screen
update when stopping themselves. This is unnecessary now because
syscons.c takes care of that.
- cleared up many unused or unnecessary #include statements.
- Removed -DLKM from Makefiles.
YOU NEED TO RECOMPILE BOTH SCREEN SAVERS AND KERNEL AS OF THIS CHANGE.
1. Add new interface, add_scrn_saver()/remove_scrn_saver(), to declare
loading/unloading of a screen saver. The screen saver calls these
functions to notify syscons of loading/unloading events.
It was possible to load multiple savers each of which will try to
remember the previous saver in a local variable (`old_saver'). The
scheme breaks easily if the user load two savers and unload them in a
wrong order; if the first saver is unloaded first, `old_saver' in the
second saver points to nowhere.
Now only one screen saver is allowed in memory at a time.
Soeren will be looking into this issue again later. syscons is
becoming too heavy. It's time to cut things down, rather than adding
more...
2. Make scrn_timer() to be the primary caller of the screen saver
(*current_saver)(). scintr(), scioctl() and ansi_put() update
`scrn_time_stamp' to indicate that they want to stop the screen saver.
There are three exceptions, however.
One is remove_scrn_saver() which need to stop the current screen saver
if it is running. To guard against scrn_timer() calling the saver during
this operation, `current_saver' is set to `none_saver' early.
The others are sccngetc() and sccncheckc(); they will unblank the
screen too. When the kernel enters DDB (via the hot key or a
break point), the screen saver will be stopped by sccngetc().
However, we have a reentrancy problem here. If the system has been in
the middle of the screen saver...
(The screen saver reentrancy problem has always been with sccnputc()
and sccngetc() in the -current source. So, the new code is doing no
worse, I reckon.)
3. Use `mono_time' rather than `time'.
4. Make set_border() work for EGA and CGA in addition to VGA. Do
nothing for MDA.
Changes to the LKM screen saver modules will follow shortly. YOU NEED
TO RECOMPILE BOTH SCREEN SAVERS AND KERNEL AS OF THESE CHANGES.
Reviewed by: sos and bde
and released. It should use `spcl' consistently in both cases,
otherwise shift/control/alt state may not be correctly set/reset.
(Even with this fix, you can still make syscons confused and fail to
change internal state if you really want to, by installing a really
arcane and artificial keymap.)
PR: i386/4030
Reviewed by: sos
cursor (CHAR_CURSOR)
1. Reduced the number of calls to set_destructive_cursor(). The
destructive cursor produced noticeable overhead on the system. It was
caused by draw_cursor_image() calling set_destructive_cursor() every
so often.
set_destructive_cursor() absolutely needs to be called when
a) the character code under the cursor has changed either because
the cursor moved or because the screen was updated or the mouse
pointer overlapped the cursor.
b) Or a new font has been loaded,
c) or the video mode has been changed,
d) or the cursor shape has been changed,
e) or the user switched virtual consoles.
2. Turn off the configuration flag CHAR_CURSOR (destructive cursor) in
scattach() if we have a non-VGA card. The destructive cursor works
only for VGA.
3. Removed redundant calls to set_destructive_cursor() in some places.
4. Fixed the "disappearing mouse pointer" problem. The mouse pointer
looked hidden under the destructive cursor when it overlaped the cursor.
A slightly different version of the patch was reviewd and OKed by
sos and ache.
Add a new configuration flag, KBD_NORESET (0x20) to tell scprobe() not
to reset the keyboard.
IBM ThinkPad 535 has the `Fn' key with which the user can perform
certain functions in conjunction with other keys. For example, `Fn' +
PageUP/PageDOWN adjust speaker volume, `Fn' + Home/End change
brightness of LCD screen. It can also be used to suspend the system.
It appears that these functions are implemented at the keyboard level
or the keyboard controller level and totally independent from BIOS or
OS. But, if the keyboard is reset (as is done in scprobe()), they
become unavailable. (There are other laptops which have similar
functions associated with the `Fn' key. But, they aren't affected by
keyboard reset.)
ThinkPad 535 doesn't have switches or buttons to adjust brightness and
volume, or to put the system into the suspend mode. Therefore, it is
essential to preserve these `Fn' key functions in FreeBSD. The new
flag make scprobe() skip keyboard reset.
If this flag is not set, scprobe() behaves in the same say as before.
(If we only knew a way to detect ThinkPad 535, we could skip keyboard
reset automatically, but...)
rather than hard-code it in the message text. Optinally include
the host name in the message if SHOW_HOSTNAME is defined.
The origianl idea and sample code submitted by Angelo Turetta
<ATuretta@stylo.it>.
adapter during the system boot. It always assumes there is at least a
monochrome adapter.
This is rather strange assumption. If there is no dispaly adapter, the
console driver cannot be any good...
In this patch, scinit() is split into two parts; the first part is
now called scvidprobe() which will detect the presence of video card
at the CGA or MONO buffer address and returns TRUE if found. It is
called during sccnprobe() and scprobe(). Both will fail if no video
card is found.
The second part, whose name stays the same as before, scinit(), is
called from sccninit() and scattach() to complete initialization of
the found video card.
The keyboard probe code is moved from scprobe() to sckbdprobe();
scprobe() now calls scvidprobe() and sckbdprobe() to carry out device
probe. (This is rather a cosmetic change, but it sure makes the code
look better organized.)
The problem pointed out by Joerg.
changes relative to the 2.2 compatable version are include file
related, the new multicast interface (!) and the new PCI interface.
This should work "as-is" but has not been tested (I have not been able
to get a dc21x4x based card for testing).
- OVERRIDE_TUNER: allows you to manually choose the tuner type for those
cards that fail to probe properly. See source for legal
values.
- OVERRIDE_DBX: allows you to manually choose DBX or NO DBX for those
cards that fail to probe properly.
0 == no DBX circuit present, 1 == DBX circuit present.
speed using the boot blocks, instead of a hardcoded value stuck in the
kernel. This way, you can have systems using the same kernel but different
console speeds.
Add a sysctl entry for changing the system console speed.
Lock the user tty speed to match the system console speed.
Nuke CONSPEED.
Reviewed by: bde
device probe of a host to PCI bridge may modify that value, based on
its knowledge of device specific registers. This makes the Intel XXpress
work, as verified by: Terje Marthinussen <terjem@cc.uit.no>.
1) Stop at the first map register that contains a zero value.
2) When testing for the map size work up from low values, since
this works around a bug in some BusLogic SCSI card, which has
the 16 upper port base address bits hardwired to zero.
The config register dump printed in the bootverbose case has
been slightly rearranged.
reality. There will be a new call interface, but for now the file
pci_compat.c (which is to be deleted, after all drivers are converted)
provides an emulation of the old PCI bus driver functions. The only
change that might be visible to drivers is, that the type pcici_t
(which had been meant to be just a handle, whose exact definition
should not be relied on), has been converted into a pcicfgregs* .
The Tekram AMD SCSI driver bogusly relied on the definition of pcici_t
and has been converted to just call the PCI drivers functions to access
configuration space register, instead of inventing its own ...
This code is by no means complete, but assumed to be fully operational,
and brings the official code base more in line with my development code.
A new generic device descriptor data type has to be agreed on. The PCI
code will then use that data type to provide new functionality:
1) userconfig support
2) "wired" PCI devices
3) conflicts checking against ISA/EISA
4) maps will depend on the command register enable bits
5) PCI to Anything bridges can be defined as devices,
and are probed like any "standard" PCI device.
The following features are currently missing, but will be added back,
soon:
1) unknown device probe message
2) suppression of "mirrored" devices caused by ancient, broken chip-sets
This code relies on generic shared interrupt support just commited to
kern_intr.c (plus the modifications of isa.c and isa_device.h).
1) Adjust NFRAMES from 16 to 8 per 16k of memory.
2) Acknowledge interrupts to the card early in the interrupt
handler before processing the event that caused the interrupt.
This frees the card to process addtional events instead of
waiting for the driver to finish handling events.
3) Changed the initialization of the transmit buffers to be a
loop so that the number of buffers can be more easily changed.
4) Moved the code to take the adapter out of loop back mode to just
before we enable the receiver.
I also made the driver dynamically size its resource arrays at attach
time so that we can take full advantage of adapters with more than 16k
of memory.
Richard has some other changes he's working on to improve performance,
but this should get ee16 support working reliably again.
Thanks to Wes Santee <wes@bogon.net> for testing these patches.
Submitted by: Richard Straka <straka@user1.inficad.com>
full implementation of the sate machine as described in RFC1661, and
provides support for plugging in various control protocols. I needed
this to provide PPP support for the BISDN project (right now).
Unfortunatley, while the existing API was almost up to the point, i
needed one minor API change in order to decouple the this-layer-
started and this-layer-finished actions from the respective Up and
Down events of the lower layer. This requires two additional lines in
the attach routines of all existing lower layer interface drivers that
are using syncPPP (shortcutting these actions and events). Apart from
this, i believe i didn't change the API of all this, so everything
should plug in without too many hassles. Please report if i broke
something in the existing drivers.
For a list of features (including new ones like dial-on-demand), and
things still to be done, please refer to the man page i'll commit asap.
Encouraged by: Serge Vakulenko <vak@cronyx.ru>
When an ioctl command SW_XXXX is issued, scioctl() checks if the font
appropriate for the specified mode is already loaded. The check was
correctly done for 8 line and 16 line fonts, but not for 14 line font.
The symbols FONT_8, FONT_14 and FONT_16 were defined as numbers but
were sometimes treated as bit flags. They are now defined as bit
flags.
2) screen blinking (two fixes)
Removed a redundant call to timeout() in do_bell().
Don't let blink_screen() write to the video buffer if the screen is in
the graphics (UNKNOWN) mode.
3) screen saver timeout
The ioctl command CONS_BLANKTIME sets the screen saver's timeout. The
value of zero will disable the screen saver. If the screen saver is
currently running it should be stopped.
4) border color and destructive cursor (two fixes)
The border color and the cursor type can be changed via escape
sequences. But only VGA can change the border color and set the
cursor type to destructive (CHAR_CURSOR) in the current syscons.
scan_esc() failed to check this.
Reviewed by: sos
. It makes cd9660 root f/s working again.
. It makes CD9660 a new-style option.
. It adds support to mount an ISO9660 multi-session CD-ROM as the root
filesystem (the last session actually, but that's what is expected
behaviour).
Sigh. The CDIOREADTOCENTRYS did a copyout() of its own, and thus has
been unusable for me for this work. Too bad it didn't simply stuff
the max 100 entries into the struct ioc_read_toc_entry, but relied on
a user supplied data buffer instead. :-( I now had to reinvent the
wheel, and created a CDIOREADTOCENTRY ioctl command that can be used
in a kernel context.
While doing this, i noticed the following bogosities in existing CD-ROM
drivers:
wcd: This driver is likely to be totally bogus when someone tries
two succeeding CDIOREADTOCENTRYS (or now CDIOREADTOCENTRY)
commands with requesting MSF format, since it apparently
operates on an internal table.
scd: This driver apparently returns just a single TOC entry only for
the CDIOREADTOCENTRYS command.
I have only been able to test the CDIOREADTOCENTRY command with the
cd(4) driver. I hereby request the respective maintainers of the
other CD-ROM drivers to verify my code for their driver. When it
comes to merging this CD-ROM multisession stuff into RELENG_2_2 i will
only consider drivers where i've got a confirmation that it actually
works.
Added [SR]RGBMASKs ioctl for byte swapping.
1.16 4/20/97 Randall Hopper <rhh@ct.picker.com>
Generalized RGBMASK ioctls for general pixel
format setting [SG]ACTPIXFMT, and added query API
to return driver-supported pix fmts GSUPPIXFMT.
1.17 4/21/97 hasty@rah.star-gate.com
Clipping support added.
1.18 4/23/97 Clean up after failed CAP_SINGLEs where bt
interrupt isn't delivered, and fixed fixing
CAP_SINGLEs that for ODD_ONLY fields.
Submitted by: individuals in above log messages.
Added [SR]RGBMASKs ioctl for byte swapping.
1.16 4/20/97 Randall Hopper <rhh@ct.picker.com>
Generalized RGBMASK ioctls for general pixel
format setting [SG]ACTPIXFMT, and added query API
to return driver-supported pix fmts GSUPPIXFMT.
1.17 4/21/97 hasty@rah.star-gate.com
Clipping support added.
1.18 4/23/97 Clean up after failed CAP_SINGLEs where bt
interrupt isn't delivered, and fixed fixing
CAP_SINGLEs that for ODD_ONLY fields.
Submitted by: individuals in above log messages.
1) i586_bcopy() problem
There have been a number of reports that the syscons doesn't work
properly if i586_bcopy() is enabled.
The problem prevented users from installing 2.2(.1)-RELEASE. The
symptom is that the system looks frozen during device probe or just
before the main installation menu. The workaround was to specify the
flag 0x01 to the npx device so that i586_bcopy() is disabled.
The patch forces the syscons to call generic_bcopy() when copying
to/from the video memory, even if CPU is Pentium and i586_bcopy() is
enabled. i586_bcopy() is still called for copy operations between
non-video memory regions.
PR: kern/2277, kern/3066, kern/3107, kern/3134
2) video mode parameter table problem
The syscons reads and uses the video mode parameter table provided by
the VGA BIOS to set VGA registers when changing video mode and
modifying font data. It appears that in some VGA BIOSes the table is
not ordered as the syscons expects, and this leads to screen
corruption.
The problem prevented users from installing 2.2(.1)-RELEASE. The
symptom is the corrupt screen or strange vertical lines soon after the
kernel is loaded into memory (just after the kernel decompression).
The patch performs simplistic test and if it fails, set video_mode_ptr
to NULL so that the video mode switching won't happen.
This is an interim kludge. There should be a better way to deal with
the problem.
PR: kern/2498, conf/2775, conf/3354
Reviewed by: sos
Tested by: PR originators (not all of them, though)
There are various options documented in i386/conf/LINT, there is more to
come over the next few days.
The kernel should run pretty much "as before" without the options to
activate SMP mode.
There are a handful of known "loose ends" that need to be fixed, but
have been put off since the SMP kernel is in a moderately good condition
at the moment.
This commit is the result of the tinkering and testing over the last 14
months by many people. A special thanks to Steve Passe for implementing
the APIC code!
if SCB Paging was enabled:
disconnect with more data to transfer
disconnected SCB gets paged out
target reconnects so we page SCB back in
target completes transfer so residual is 0
target disconnects
SCB gets reused but not paged out since the residual is 0 (optimization)
target reconnects so we page the SCB back in
we report a residual because of stale residual information.
The fix for this is to set a flag that forces the SCB to be paged back
up to the host if we page in an SCB with a residual
Pointed out by: Doug Ledford <dledford@dialnet.net>
large enough to contain the ethernet header. There appears to be a
condition where the card can return "0" in some failure cases, and this
causes bad things to happen (a panic).
type mismatches. mcd and scd were/are particularly bogus. They
used a general purpose function taking 2 args for the timeout
function and fudged varargs stuff to supply the second arg for the
timeout case. This broke `cc -mrtd'. Bounce through a timeout
function instead. The timeout arg still gets bogusly cast from
int to `void *' and back.
to fix a selection timeout problem.
If we can't find an SCB for the reconnecting target, issue a bus device
reset as the SCSI2 spec suggests.
Add a missing call to "add_scb_to_free_list" in the non paging case. In
the non-paging case, the SCBs don't really need to be on the free list,
but putting them there clears the tag field which is something the recovery
code depends on.
This patch fixes the problem of vic only capturing an even or odd frame plus
the my early patch for missing frames with resolutions higher than 320x240
in rgb mode.
The yuv422 patch introduces a minor bug in that a green line appears at the
bottom of the captured window . There is no easy work around for this right
now.
Reviewed by: various bt848 hackers
Submitted by: Amancio Hasty <hasty@rah.star-gate.com>
for the ix driver.
Add a shutdown hook that resets the etherexpress so that Windoze can find
the card after a warm boot.
Submitted by: Aaron Smith <aaron@tau.veritas.com>
Obtained From: NetBSD
Be consistant about testing for parity errors after waiting for a
REQ on the bus.
Don't ack the last byte in a transaction until after we've cleared
all target state.
aic7xxx_asm.c:
Test the return value of getopt against -1 not EOF. (Yet another
shameless victum of the style guide being wrong).
resetting the keyboard.
Well, sorry, this bug is totally my fault. I DID intend to preserve
them, but somehow I failed.
The bug puts some old keyboard controllers in a strange state,
resulting in keyboard freeze or random key input.
The fix closes PR kern/3067.
Use the name argument almost the same in all LKM types. Maintain
the current behavior for the external (e.g., modstat) name for DEV,
EXEC, and MISC types being #name ## "_mod" and SYCALL and VFS only
#name. This is a candidate for change and I vote just the name without
the "_mod".
Change the DISPATCH macro to MOD_DISPATCH for consistency with the
other macros.
Add an LKM_ANON #define to eliminate the magic -1 and associated
signed/unsigned warnings.
Add MOD_PRIVATE to support wcd.c's poking around in the lkm structure.
Change source in tree to use the new interface.
Reviewed by: Bruce Evans
Use the name argument almost the same in all LKM types. Maintain
the current behavior for the external (e.g., modstat) name for DEV,
EXEC, and MISC types being #name ## "_mod" and SYCALL and VFS only
#name. This is a candidate for change and I vote just the name without
the "_mod".
Change the DISPATCH macro to MOD_DISPATCH for consistency with the
other macros.
Add an LKM_ANON #define to eliminate the magic -1 and associated
signed/unsigned warnings.
Add MOD_PRIVATE to support wcd.c's poking around in the lkm structure.
Change source in tree to use the new interface.
Reviewed by: Bruce Evans
loop, test for them separately. The bug report from David Malone showed that
even though we had been reselected (SELDI was true), we sat in the poll for
work loop until the selection timeout timer expired. It may be that the
SSTAT0 register doesn't like to have more than one bit tested at a time.
I've seen stranger things than this on these parts.
(see LINT). There is a new low-level console type that is more suitable
for use with gdb-remote.
Fixed setting of speed at probe time for the serial console (if any).
Reviewed by: dfr
either by looking it up in the array of pending, per target, untagged
transactions, or by using the tag value passed in during the identify. The
old code only direct indexed for tagged transactions. This makes the
"findSCB" routine only necessary when SCB paging is enabled, so appropriately
conditionalize it. This greatly simplifies the non SCB paging code flow.
change typematic rate, or the X server (XFree86 or Accelerated X)
starts up.
So far, there have been two independent reports from Dell Latitude XPi
notebook/laptop owners. The Latitude seems to be the only system which
suffers from this problem. (I don't know the problem is with the
entire Latitude line or with only some Latitude models) No problem
report has been heard about other systems (I certainly cannot
reproduce the problem in my -current and 2.2 systems).
In 3.0-CURRENT, 2.2-RELEASE and 2.2-GAMMA-970310, when programming the
keyboard LED/repeat-rate, `set_keyboard()' in `syscons' tells the
keyboard controller not to generate keyboard interrupt (IRQ1) and then
enable tty interrupts, expecting the keyboard interrupt doesn't occur.
It appears that somehow Latitude's keyboard controller still generates
the keyboard interrupt thereafter, and `set_keyboard()' doesn't see
the return code from the keyboard because it is consumed by the
keyboard interrupt handler.
The patch entirely disables tty interrupts while setting LED and
typematic rate in `set_keyboard()', making the routine behave more
like the previous versions of `syscons' (versions in 2.1.X and
2.2-ALPHA, -BETA, and some -GAMMAs). The reporter said this patch
eliminated the problem.
(I also found another typo/bug, but the reporter and I found that it
wasn't the cause of the problem...)
This should go into RELENG_2_2.
Randall Hopper <rhh@ct.picker.com> GHUE/GBRIGHT bug
Louis Mamakos made a new bt848 struct, including massive changes to the entire
body of code, substituting array offsets with struct members.
Randall Hopper aadded fixes of BT848_GHUE & BT848_GBRIG.
I (fsmp):
added polled hardware i2c routines,
removed all existing software i2c routines.
added eeprom support.
<sys/ioctl_compat.h> and sometimes <sys/filio.h> instead of
<sys/ioctl.h> in tty-related files. <sys/ttycom.h> is still
usually imported bogusly via <sys/termios.h>.
Michael submitted code to activate the audio muxes.
fsmp:
extended those changes for different boards.
auto-detection of board types.
auto-detection of tuner types.
auto-detection of stereo option.
Michael submitted code to activate the audio muxes.
fsmp:
extended those changes for different boards.
auto-detection of board types.
auto-detection of tuner types.
auto-detection of stereo option
Fixed a bug in fxp_mdi_write - a hex number was missing a preceding 0x
and this was causing the routine to not wait for a PHY write to complete.
Added support for link0, link1, and link2 flags to toggle auto-
negotiation, 10/100, and half/full duplex:
link0 disable auto-negotiation
When set, these flags then have meaning:
-link1 10Mbps
link1 100Mbps
-link2 half duplex
link2 full duplex
...needs a manual page.
Stick 4 more, twin channel only, instructions behind
.if ( TWIN_CHANNEL)
aic7xxx_asm.c:
Add the -O options which allows the specification of which options
to include in a program listing. This makes it possible to easily
determine the address of any instruction in the program across
different hardware/option configurations. Updated usage() as well.
I broke the cable tuning with my 'TEST_A' code. Remove TEST_A define
till I finish this change for both tuning modes. Note that this
will effectively break the new TVTUNER_SETFREQ/TVTUNER_GETFREQ ioctl()s.
These aren't used by anyone but me yet (attempt to provide full resolution
fine tuning for "fringe" stations) so it should be no problem
written:
1) Full duplex mode is now supported (and works!)
2) The 10Mbps-only PCI Pro/10 should now work (untested, however)
Thanks to Justin Gibbs for providing a PCI bus analyzer trace while the
Intel Windows driver was configuring the board...this made it possible
to figure out the mystery bit that I wasn't setting in the PHY for full
duplex to work.
devtotty(). devtotty() must check its arg carefully since the arg is
supplied as ioctl data. This should fix PR3004.
Renamed devtotty() to snpdevtotty().
New sequencer assembler for the aic7xxx adapters. This assembler
performs some amount of register type checking, allows bit
manipulation of symbolic constants, and generates "patch tables"
for conditionalized downloading of portions of the program.
This makes it easier to take full advantage of the different
features of the aic7xxx cards without imposing run time penalies
or being bound to the small memory footprints of the low end
cards for features like target mode.
aic7xxx.reg:
New, assembler parsed, register definitions fo the aic7xxx cards.
This was done primarily in anticipation of 7810 support which
will have a different register layout, but should be able to use
the same assembler. The kernel aic7xxx driver consumes a generated
file in the compile directory to get the definitions of the register
locations.
aic7xxx.seq:
Convert to the slighly different syntax of the new assembler.
Conditionalize SCB_PAGING, ultra, and twin features which shaves
quite a bit of space once the program is downloaded.
Add code to leave the selection hardware enabled during reconnects
that win bus arbitration. This ensures that we will rearbitrate
as soon as the bus goes free instead of delaying for a bit.
When we expect the bus to go free, perform all of the cleanup
associated with that event "up front" and enter a loop awaiting
bus free. If we see a REQ first, complain, but attempt to
continue. This will hopefully address, or at least help diagnose,
the "target didn't send identify" messages that have been reported.
Spelling corrections obtained from NetBSD.
. properly declare the variable in in a .h file, as opposed to
using a private extern declaration in userconfig.c;
. move the definition of EISA_SLOTS and therefore the inclusion of
opt_eisa.h into eisaconf.c.
probing anytime soon, make EISA_SLOTS a fully supported option. It's
required for the HP NetServer LC series machines.
Next stop: make dset(8) aware of it as well.
valid signals, else return EINVAL for ioctl VT_SETMODE.
this fixes a problem that anybody with vty access can panic the system.
2.2-Candidate (and 2.1.0 I believe)
Reviewed-by: sos
time that we really want to do this is when a bus reset causes the sequencer
to be reset and the kernel driver now handles this case.
Remove some reordering in the select2 routine that wasn't necessary.
It was an experimental fix for a race condition I fixed elsewhere, and
confused the code flow.
Don't bother looping on a parity error in the mesgout loop since we can't
see parity errors on out phases.
Clean up the mesgin_identify code. In the old days, we "snooped" for tag
messages and used this as an indicator of whether or not the target was
using tagged transactions. This forced the sequencer to ack the identify
before determining if a valid SCB matched the target meaning that an abort
message to handle this case might not be seen before the target entered a
data phase. Since we can determin the "tagged-ness" of a target by looking
it up in the array of busy targets (recently introduced), we can determine
this up front simplifying the search code as well as ensuring we can follow
the SCSI specs method for rejecting a reselection.
When an SCB is placed on the free list, set its SCB_TAG to SCB_LIST_NULL.
This makes it much easier for the kernel driver to find active SCBs on the
card during error recovery.
negotiation messages may be tagged, we were overrunning the old buffer.
The variable that was getting squashed is updated before the message goes
out, causing corrupted SDTR or WDTR messages. Depending on the phases
traversed before message out, this could cause the wrong offset to be
negotiated allowing data overruns to occur. The problem is easier to
detect with wide targets on the chain since the allowed offset is smaller.
Also removed the unnecessary clearing of SPIORDY during the message out
phase. We don't rely on SPIORDY any more.
When setting the HCNT registers, do so in ascending order.
When performing tagged queueing in non-paging mode, also check the
disconnected bit in the SCB as extra sanity during a reconection.
Make the labels in the DMA routine more sane.
When doing a DMA, if we see the DMADONE condition come true, we can
simply turn of the DMA enable bits in DFCNTRL without testing the FIFO
state as HDONE is true when DMADONE is true and this emplies the FIFO is
empty.
These changes clear up the data overrun error messages and seem to prevent
the "timed out in data-in phase" problems.
changes, so don't expect to be able to run the kernel as-is (very well)
without the appropriate Lite/2 userland changes.
The system boots and can mount UFS filesystems.
Untested: ext2fs, msdosfs, NFS
Known problems: Incorrect Berkeley ID strings in some files.
Mount_std mounts will not work until the getfsent
library routine is changed.
Reviewed by: various people
Submitted by: Jeffery Hsu <hsu@freebsd.org>
free.
When we clear SCSIRATE, also clear the FAST20 bit in SXFRCTL0. This also
allowed me to clean up some of the ULTRA code.
ULTRAENB->FAST20 to follow the convention in the Adaptec data books.
Fix the data-overrun code to set both stcnt and hcnt otherwise, the transfer
will just hang until we get a timeout.
Add implicit support for the NOOP message. I've never heard of the driver
issueing a reject for one, but its silly to reject NOOP and who knows how a
device might react.
In the dma routine, check SDONE before cleaing SDMAEN. The data books mention
SDONE possibly being cleared when SDMAEN is reset. Clients of dma now need
to check if SINDEX is cleared to know if a phasemis occured.
Fix some comments to be correct.
This parameter is intended to allow new kernels to work with old LKM binaries,
provided the revision ID is incremented whenever the PCI LKM interface is
changed. The revision ID does not at all protect against changes in data
structures accesses by the driver.
Disabled the DMA byte counters - I had it this way originally and this is
the recommended setting.
Set crscdt to CRS only (0) since this is what it should be for an MII PHY.
Also fixed some comments.
host DMAs. The additional test to ensure that the DMA has stopped is also
unnecessary since we've already waited for the DMA to complete.
Update my copyright for the new year.
with <= 100 usec between each character arrival time. This didn't happen
until rev.1.75 of clock.c because DELAY(100) used to delay for closer to
80 usec than 100 usec, and the minimum time between character arrivals is
87.8 usec at the maximum supported speed of 115200 bps 8N1.
Clear DCD timestamp flag on close (the input timestamp flag is already
cleared).
key "print scrn".
It used to stop at the first non-open vty, now it skips the non-open
ones and thereby enable one to cycle around all open vty by pressing
"print scrn".
- don't uselessly initialize the fifo "DMA" bit at attach time.
- initialize the fifo "DMA" bit at open time. Without this, the device
interrupts for every character received, reducing input performance
to that of an 8250.
- don't uselessly initialize the fifo trigger level to 8 (scaled to
256) at attach time.
- don't scale the fifo trigger level to 512 bytes. The driver's pseudo-
dma buffer has size 256, so it can't handle bursts of size 512 or 256.
It should be able to handle the second lowest ftl (2 scaled to 64).
- don't reset the fifos in siostop(). Reset triggers a hardware bug
involving wedging of the output interrupt bit This workaround
unfortunately requires ESP support to be configured.
Expand the boundaries of a pause disabled region to close of possible race
condition.
Revert a portion of the DMA code to fix false overruns.
Add a missing "add_scb_to_free_list" so we don't leak SCBs.
SDONE, not HDONE.
In the data phase dma handler, mask off just the enable bits instead of
clearing the whole register. Clearing the direction bit could be bad.
Also don't stop a DMA until MREQPEND goes false. Doing this may cause
an ABORT on the PCI bus although I have yet to see this happen.
Add definitions for MREQPEND and the BRDCTL register. The BRDCTL register
is used to handle high byte termination and automatic termination testing.
Only enable reselections once the channel and SCSIRATE have been cleared.
Add a pause block around the test busy code in the non-tagged case to simplify
error recovery in the corner case of aborting an SCB that just got started.
Simplify reselection processing by removing the call to initialize_scsiid.
Clear the scsiseq re/select control bits and setup for catching bogus
busfrees earlier in the re/select process.
Improve the automatic PIO code. It turns out that SPIORDY is not a reliable
hardware condition bit, so use REQINIT intstead. Don't rely on PHASEMIS
either since it can take too long to come true. Use a brute force comparison
instead.
Remove some unnecessary overhead in the command complete processing. It
should be nearly impossible to overflow the QOUTFIFO (worst case 9 command
have to complete with at least 6 of them requiring paging on an aic7850),
so don't take the additional PIO hit to guard against this condition. If we
don't see our interrupt in time, the system has bigger problems elsewhere.
If this ever does happen, the timeout handler will notice and retry the
command.
an X seesion. Really stupid error of me, and I've been looking at
this code SO many times. Thanks to Kazutaka YOKOTA for seeing this..
Submitted by: Kazutaka YOKOTA
one in draw_mouse causes spontanious hangs on my p5-100 when I
move the mouse excessively. Forgot that on the last commit, so
using the mouse or destructive cursor would produce large amounts
of flicker..
now dead sys/pci/if_pdq.c which has been committed about by the same
time i made my tests with Matt's code.
LINT should compile now again.
Well, that's a clear case where ``CVS writer locks'' would certainly
(not) have helped. :-]
to -current.
Thanks goes to Ulrike Nitzsche <ulrike@ifw-dresden.de> for giving me
a chance to test this. Only the PCI driver is tested though.
One final patch will follow in a separate commit. This is so that
everything up to here can be dragged into 2.2, if we decide so.
Reviewed by: joerg
Submitted by: Matt Thomas <matt@3am-software.com>
importing it onto a vendor branch first, in the hope that this will
make future maintenance easier.
The conflicts are (hopefully) unimportant. More commits that actually
bring this into the source tree will follow.
Submitted by: Matt Thomas (thomas@lkg.dec.com)
cur_console is NULL when copy_font() is first called from scinit(). This
is apparently harmless when scinit() is called early from sccninit() -
page 0 is apparently mapped r/w then, and 0->status contains suitable
garbage. However, when there is a serial console, scinit() is first
called from scattach() when the page tables are completely initialized,
so the NULL pointer causes a panic.
Submitted by: bruce
I have no idea if this works since I don't have one of the cards to test.
I also don't know what the LINT and GENERIC entries should look like,
so I just made up some values for now and left them commented out.
Someone who knows the factory settings for a Pro/10, please contact me!
Submitted-By: Javier Martín Rueda <jmrueda@diatel.upm.es>
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
previous hackery involving struct in_ifaddr and arpcom. Get rid of the
abominable multi_kludge. Update all network interfaces to use the
new machanism. Distressingly few Ethernet drivers program the multicast
filter properly (assuming the hardware has one, which it usually does).
EISA slots to probe. This is mainly intended to allow installing the
system on an HP Netserver with an on-board AIC7xxx EISA SCSI
controller, that is sitting on EISA slot # 11.
Documentation updates explaining this hack will follow shortly.
Note that this can go away again as soon as the EISA device probing
is more intelligent about the address space clash with the PCI address
space.
2.2 candidate.
Not objected by: freebsd-core :)
to TAILQs. Fix places which referenced these for no good reason
that I can see (the references remain, but were fixed to compile
again; they are still questionable).
type to be int so that errors can be returned.
2) Use the new SIOCSIFMTU ether_ioctl support in the few drivers that are
using ether_ioctl().
3) In if_fxp.c: treat if_bpf as a token, not as a pointer. Don't bother
testing for FXP_NTXSEG being reached in fxp_start()...just check for
non-NULL 'm'. Change fxp_ioctl() to use ether_ioctl().
to miss reselections from some devices and since the reselection response
timeout is only 200ns, enabling reselections too late may be the cause of our
problem.
function ed_attach_NE2000_pci() in if_ed.c passes
an uninitialized block of memory (got with malloc())
to ed_attach. This prevents a proper initialization
of the device descriptor and in my case causes a panic
during the probe, while printing out device info.
Reviewed by: phk
Submitted by: Luigi Rizzo <luigi@iet.unipi.it>
1. 'connector_table' is shortened to 'conn_tab'.
2. More reliable connector change code.
3. Display message like "vx0: selected bnc. (link1)"
when the connector changed by link[012].
4. Handle MII properly.
5. Potentially slightly better performance.
6. Fixed a silly typo.
Submitted by: Naoki Hamada <nao@sbl.cl.nec.co.jp>
1. 'connector_table' is shortened to 'conn_tab'.
2. More reliable connector change code.
3. Display message like "vx0: selected bnc. (link1)"
when the connector changed by link[012].
4. Handle MII properly.
5. Potentially slightly better performance.
6. Fixed a silly typo.
Submitted by: Naoki Hamada <nao@sbl.cl.nec.co.jp>
1. All the suggestions earlier made by Bruce: renaming some symbols,
stricter error checking, removing redundant code, etc.
2. The `psm' driver preserves the default counter resolution and
report rate, whatever they are after reset. (Based on reports and
suggestion from Nate and Rob Bolin).
3. The `psm' driver now does not check the so-called sync. bit in the
first byte of the data packet by default, so that the tapping feature
of ALPUS GlidePoint works (based on reports from Louis Mamakos). I
tested the code with ALPUS Desktop GlidePoint (M/N GP101) and found
no problem; tapping worked. It appears ALPUS produces several models
of GlidePoint. I hope the other models are OK too.
The check code can still be activated by defining the PSM_CHECKSYNC
option in the config file. (The bit checking slightly reduces, if not
completely eliminates, weird mouse behavior cased by unsynchronized
mouse data packets. It also helps us to detect if the mouse interrupt
can ever be lost. But, well, if there are devices which cannot be
supported this way...)
4. The `psm' driver does not include the protocol emulation code by
default. The code can still be compiled in if the PSM_EMULATION option
is specified in the config file. Louis Mamakos suggests the emulation
code is putting too much in the kernel, and `moused' works well.
I will think about this later and decide if the entire emulation
code should be removed.
5. And, of course, the fix in `scprobe()' from Bruce to cure the
UserConfig problem. My code in `kbdio.c' is slightly different from
his patch, but has the same effect. There still is a possibility that
`scprobe()' gets confused, if, for whatever reasons, the user holds
down a key for very long time during the boot process. But we cannot
cope with everything, can we?
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
a) Removal of private typedefs tulip_uint*_t, use standard u_int_*_t.
b) Change [Dd][Cc]21.4. to just 21.4., seems Dec has done this to all
of the drivers for all OS's. (Did they get in trouble with someone?)
[The few that remain can either not be eliminated, or are waiting for
additional driver functional changes that will remove them.]
c) Move some code from dc21040.h into the driver, later a whole block of that
code and more will move to devar.h, but for now this makes it easier
to study diffs.
d) Add a big bold comment to the README.de file about it not reflecting
reality anymore.
Note that these are all cosmetic changes and should be no functional
change in the driver whatsoever. If _anyone_ spots a problem introduced
by this please let me know ASAP!
are always together with Framing Errors and they were incorrectly
treated as FE's and discarded.
Reorganized the BREAK/FE/PE tests.
Found by: NIST-PCTS
with sio devices (not perfectly, since there is no way to flush the tx
holding register on 8250-16450's. I'm not sure if resetting the fifos
flushes the tx shift register).
Reminded by: NIST-PCTS
is completely empty. There is no interrupt for output completion, so
poll for it every 10 ms after output is nearly complete. Now ttywait()
works right.
Reminded by: NIST-PCTS
Immediate SCBs, since they always send messages that tell the target to
transition to bus free now rely on the busfree interrupt instead of the
IMMEDDONE sequencer interrupt that was generated before.
Rearrange some code in the message out loop to give ATN a little more time
to drop before we ACK the last byte.
Use SPIORDY instead of REQINIT when snooping for a tag message on a reconnect.
This is done for the same reasons we use SPIORDY in the inb functions.
When going into BITBUCKET mode, turn off HDMAEN in the DFCNTRL register so
that we can "not care" what the value of HCNT is. If HCNT is 0, BITBUCKET
mode won't transfer any data if HDMAEN is set. Seeing as we don't want the
transfer to even think about touching the host, this seems more sane anyway.
Thanks to "Dan Willis" <dan@plutotech.com> for pointing out that this was
a problem.
SPIORDY should go active on any REQ of the bus, so testing for REQINIT is
not necessary. It also seems that testing for SPIORDY is more robust then
REQINIT since SPIORDY comes active after REQINIT and PHASEMIS seems to take
some time to come true after REQ is asserted if the phase has changed. Of
course, none of this is documented.
This should give the code savings of my original changes, without breaking the
driver on fast peripherals.
The 'getchar' function in syscons (sccngetc) is used by UserConfig to
get keyboard input from the user. When it was modified to use the
shared keyboard port routines it used the port passed in during the
probe routine. Since the probe routine was not yet called, the port was
set to 0, which is obviously not going to work.
Pre-initialize sc_port to IO_KBD which is really a kludge, but it's how
the previous driver did it's job.
Found by: remote GDB
initial selection when entering the status phase. This is the same assertion
we use for all the other data transfer phases.
Hopefully fix the hangs in the mesgin and mesgout phases that I introduced
last week during some code cleanup. I need to get some of these 12MB/s
drives so I can reproduce these hangs here...
Add a pause disable in the SCB paging case around our manipulation of the
QOUTQCNT variable. This is simply extra sanity.
Set LASTPHASE to P_BUSFREE once we see a busfree so that the kernel driver can
differentiate this from a data out phase.
syscons and psm, curtesy Kazutaka Yokota with minor changes by
me. This contains an update of the psm driver as well.
This also fixes the breakage that I introduced to the psm driver by
making syscons poll for keyboard events in the atempt to fix the
hanging keyboard problem.
It works perfectly for me, and I'd like to hear from all that
have had keyboard/ps/2 mouse problems if this is the cure...
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
almost complete control over RTS (control of its initial value is still
missing).
This fixes PR 1644 for sio.
The author of PR 1644 wants it in 2.1.6 and 2.2. This may be safe since
the complications are only in rarely used cases that I hope I've covered.
bridges with support for 64 bit memory addresses and 32 bit I/O addresses).
The code is not complete. It ignores the upper half of the long addresses.
This is not a problem on PC compatible systems, but has to be fixed for
real computers.
actually harmless.
2. Fixed code to match comment in scintr().
3. Don't allow even root to take control of the machine when securelevel > 0.
I've secured the accesses to PSL_IOPL in all drivers and asked pst to
review it, but he seems to be busy. Write access to /dev/kmem and
other critival devices currently leaks across raisings of securelevel
via open fd's, so there may as well be a similar leak for PSL_IOPL.
4. (Most important.) Don't corrupt memory beyond the screen buffers if
the cursor happens to be off the 80x25 screen when syscons starts.
5. Fix console cursor update (not perfect yet).
Submitted by: bruce
~
getting the same behavior using the flags, which can be done inside of
UserConfig. (Also document other syscons flags which were previously
undocumented).
Requested by: bde
1) get_free_or_disc_scb was not being passed its argument correctly
in one case
2) Add protection in the form of the QOUTQCNT variable to prevent
overflowing the QOUTFIFO.
This should make SCB Paging work. Really, I mean it now. 8-)
This allows the user to add modify syscons's configuration flags using
UserConfig that will allow older/quirky hardware (most notably older IBM
ThinkPad laptops) to work with the standard boot kernel.
Inspired by: The Nomads
3COM 3C590 Etherlink III PCI,
3COM 3C595 Fast Etherlink PCI,
3COM 3C592 Etherlink III EISA,
3COM 3C590 Fast Etherlink EISA,
3COM 3C900 Etherlink XL PCI and
3COM 3C905 Fast Etherlink XL PCI.
This driver is based on OpenBSD's driver. I modified it to run under FreeBSd
and made it actually work usefully.
Afterwards, nao@tom-yam.or.jp (HAMADA Naoki) added EISA support as well as
early support for 3C900 Etherlink XL PCI and 3C905 Fast Etherlink XL PCI.
He also split up the driver in a bus independant and bus dependant parts.
Especially the 3c59X support should be pretty stable now.
Submitted by: partly nao@tom-yam.or.jp (HAMADA Naoki)
Obtained from:partly OpenBSD
appearance of this bug was the malfunctioning -M option in GNU tar (it
worked only by explicitly specifying -L).
Reviewed by: bde, and partially corrected accoring to his comments
Candidate for 2.2, IMHO even for 2.1.6.
(1) deleted #if 0
pc98/pc98/mse.c
(2) hold per-unit I/O ports in ed_softc
pc98/pc98/if_ed.c
pc98/pc98/if_ed98.h
(3) merge more files by segregating changes into headers.
new file (moved from pc98/pc98):
i386/isa/aic_98.h
deleted:
well, it's already in the commit message so I won't repeat the
long list here ;)
Submitted by: The FreeBSD(98) Development Team
Check that a received packet isn't longer than MCLBYTES. This will
sometimes happen if a cable is plugged into or removed from a live
system.
Try to cater better for early receive interrupts.
used mvi instead of mov. Luckily this code is most likely never executed
since it is only there for sanity should a target goes into the data phase
twice during a single selection or reselection.
TIMER_FREQ.
Fixed missing splx() in scrn_timer(). The bug was harmless because of the
undocumented behaviour that the ipl is automatically restored for timeout
functions (see softclock()). Perhaps we should depend on this behaviour.
Fixed the ddb fix in rev.1.176. The in_debugger flag was no use because
it only works when the debugger is entered via the keyboard hotkey. The
debugger may be entered for breakpoints and traps, and the console putc
routine has no way of knowing when it was, so the console putc routine
must (almost?) always remove the cursor image.
Not fixed: console switching in ddb doesn't work (ISTR it working), and
console 0 shouldn't be switched to for the debugger hotkey unless console
0 is /dev/console.
Fixed side effects from calling add_keyboard_randomness() in the console
getc routine by not calling it. add_keyboard_randomness() currently
always reenables interrupts on 386's and 486's. This is very bad if the
console getc routine is called from the debugger and the debugger was
entered with interrupts disabled.
Fixed preservation of initial screen and now-bogus comment about it. It
was broken by setting the initial scr_buf to `buffer' instead of Crtat.
`buffer' was full of nulls and the first scroll cleared everything above
the things written through syscons.
Submitted by: bruce (bde@freebsd.org)
SCB paging is now handled almost entirely by the sequencer and also uses
DMA. This should make SCB paging at least an order of magnitude more
efficient and vastly simplifies the implementation.
Add a few space optimizations so this code still fits on aic7770 chips.
Update comments.
bit (0x0008) in the sc driver configuration line. This way it's easy to
boink a generic kernel.
Also, document and place in an opt_ file the #define's for overriding which
serial port is the system console.
Approved by: sos
Garrett Wollman sent me this code a few weeks ago for review, and I made
some significant changes, which he in turn accepted ...
In order to make use of these changes, a device entry has to added to /dev.
Submitted by: wollman
there is keyboard input.
The mousepointer is shown again immediately if moved.
Also a function pointer used to install a userwritten extra
ioctl handler (sc_user_ioctl). This way its is possible to
install user defined videomodes etc etc. No further changes
should be in the kernel.
<net/if_arp.h> and fixed the things that depended on it. The nested
include just allowed unportable programs to compile and made my
simple #include checking program report that networking code doesn't
need to include <sys/socket.h>.
I have only tested the ABP5140 card and only with a single CDROM drive
but it seems to work fine. This driver relies on features found only in
the SCSI branch so will not work in -current until those changes
are brought in. It also doesn't have any error handling code *yet*.
The goal is to use this driver as the development platform for the new
generic SCSI layer error recovery/handling code.
PCI and EISA front ends will show up as soon as I get my hands on
the cards. There are also a few issues in the driver that I need
to clear up with AdvanSys before I can suggest sticking one of
these cards in your server. 8-)
Thanks to AdvanSys for releasing this code under a suitable copyright.
Obtained from: Ported from the Linux driver writen by
bobf@advansys.com (Bob Frey).
divisor latch registers if the registers wouldn't change.
Use the default console cfcr setting while setting the divisor
latch registers for console i/o. Input may be messed up by
transiently changing the cfcr.
Use a usual cfcr setting while setting the divisor latch registers
in the probe. This shouldn't matter, but this is not the place to
test the UART's handling of 5 bit words.
Removed a stale devfs comment.
not resuming the NIC as required for transmit. Thanks to Alan Cox
<alc@cs.rice.edu> for noticing this.
Added another performance optimization to compensate. :-)
Changed crscdt to 1...strange, but this seems to be needed for some reason
despite what the manual says.
ring that caused wrong things to happen sometimes.
Doubled the number of transmit descriptors to 128 so that the internal
FIFO in the NIC can be fully filled when dealing with small packets.
Several minor performance improvements.
- don't include <sys/ioctl.h> in any header. Include <sys/ioccom.h>
instead. This was already done in 4.4Lite for the most important
ioctl headers. Header spam currently increases kernel build
times by 10-20%. There are more than 30000 #includes (not counting
duplicates) for compiling LINT.
- include <sys/types.h> if and only it is necessary to make the header
almost self-sufficient (some ioctl headers still need structs from
elsewhere).
- uniformized idempotency ifdefs. Copied the style in the 4.4Lite
ioctl headers.
to deal with the fact that we relied on devconf to do the shutdown
callouts in various drivers. The changes in this commit are to add support
for device shutdown in this driver via the new at_shutdown() mechanism.
Similar changes need to be made to all of the other drivers that need
a shutdown routine called (if_de.c comes to mind immediately).
changes. This version should fix a number of bugs such as with auto-
speed sensing and at least one known panic.
Submitted by: Matt Thomas (matt@3am-software.com)
instead of 0 if there is no input.
syscons.c:
Added missing spl locking in sccncheckc(). Return the same value as
sccngetc() would. It is wrong for sccngetc() to return non-ASCII, but
stripping the non-ASCII bits doesn't help.
still being used just to support printing of the device name in the
probe. Restored the method used in rev.1.6 and changed it to print
the same strings as the previous revision.
Reviewed by: Paul Richards
(1) Add PC98 support to apm_bios.h and ns16550.h, remove pc98/pc98/ic
(2) Move PC98 specific code out of cpufunc.h (to pc98.h)
(3) Let the boot subtrees look more alike
Submitted by: The FreeBSD(98) Development Team
<freebsd98-hackers@jp.freebsd.org>
and xdm, possibly in general.
What was happening was that the server was doing a tcsetattr(.. TCSADRAIN)
on the mouse fd after a write. Since /dev/sysmouse had a null t_oproc,
the drain failed with EIO. Somehow this spammed XFree86 (!@&^#%*& binary
release!!), and the driver was left in a bogus state (ie: switch_in_progress
permanently TRUE).
The simplest way out was to implement a dummy scmousestart() routine to
accept any characters from the tty system and toss them into the void.
It would probably be more correct to intercept scwrite()'s to the mouse
device, but that's executed for every single write to the screen.
Supplying a start routine to eat the characters is only executed for the
mouse port during startup/shutdown, so it should be faster.
This enables other consumers of the mouse, to get it info via
moused/syscons.
In order to use it run moused (from sysconfig), and then tell
your Xserver that it should use /dev/sysmouse (mknod sysmouse c 12 128)
and it a mousesystems mouse. Everybody will be happy then :)
Remember that moused still needs to know what kind of mouse you
have..
Comments welcome, as is test results...
(A pointer to a const was misused to avoid loading loading the same
value twice, but gcc does exactly the same optimization automatically.
It can see that the value hasn't changed.)
If you define this, it means your keyboard is actually probable using the
brain-dammaged probe routine in syscons, and if the keyboard is NOT found,
then you don't want syscons to activate itself further.
This makes life sane for those of us who use serial consoles most of the
time and want "the right thing" to happen when we plug a keyboard in.
way it attaches multiple PCI buses directly to the CPU, instead of having
them hanging off from PCI to PCI bridges. This code is a hack, and will
be obsoleted by the planned rework of the PCI code, which will change the
dealing with PCI to PCI bridges and other special devices significantly.
The patch also adds a kern_devconf entry for PCI bus 0 which is assumed
to be a child of cpu0. The new PCI code will make it possible to hand out
the kern_devconf structure to a pci device being attached, since this is
(regretably, IMHO) required by a few ISA devices.
Finally there are new PCI ids for some Intel chip set devices, which had
already been known to 2.1.5R, but did not make it into -current. This closes
"kern/1558: PCI probe seems to have lost a device in -current".
with an inconsistent state. I think the return actually "can't happen".
Cleaned up style of recent changes.
I only fiddled with this because of bugs in recent changes.
note that at_shutdown has a new parameter to indicate When
during a shutdown the callout should be made. also
add a RB_POWEROFF flag to reboot "howto" parameter..
tells the reboot code in our at_shutdown module to turn off the UPS
and kill the power. bound to be useful eventually on laptops
during phk's staticize/cleanup commits. pstat needs it, the MAXCONS
option is not visible anywhere else, and pstat uses it to find the bounds
of the sccons[MAXCONS] array, which varies.
for work regardless of whether there was an interrupt. This needs more
work, it should be able to run better when there are more than 3 host
cards present, ie: all cards in polling-only mode with no IRQ. (The
host cards have a choice of 3 irq's, 11, 12, or 15, or just polling)
and then never accept for sending packet from upper layer anymore
(i.e. ping -f )
Reviewed by: David Greenman <dg@root.com>
Submitted by: amurai@spec.co.jp
blocked in a write() while waiting for the output to drain, sleep only
for tp->t_timeout, not forever. This only seems to happen when there is
either a modem lockup holding the hardware flow control down, or due to
some problem in the driver with processes attempting to write after the
modem has hung up (eg: elm, tf).
Saves about 280 butes of source per driver, 56 bytes in object size
and another 56 bytes moves from data to bss.
No functional change intended nor expected.
GENERIC should be about one k smaller now :-)
of this patch, which had not actually been reviewed by Joerg or Paul!
(I'll better stop committing files after midnight ...)
I'm now commiting the latest code, which has been reported to work.
Minor correction to the previous commit message for this file:
The first PCI Lance in a system will get a name of lnc1, the second
will be known as lnc2 and so on. An arbitrary number of cards is
supported in a system ...
