using a cardbus based system with pccbb providing the pcic interface).
Something isn't quite right.. when the driver allocates and activates
its resources, the IO space that was requested reads as all zeros (versus
the original 0xff's as it normally is when there is no device responding).
Also, deactivate the resources before releasing them. OLDCARD doesn't
seem to care but NEWCARD/CARDBUS get rather unhappy if you release
a resource that hasn't been deactivated yet.
Make pcic_p.c only compile with oldcard kernels.
(identified by the IO map being 256 bytes long instead of 128)
This chip works very unreliably on my Lanner embedded PC with the rl driver.
Lots of watchdog timeouts or poor performance.
Forcing the media type to 10 Meg (ifconfig rl0 media 10baseT/UTP) is a good
workaround.
This looks very similar to the problem reported in PR kern/18790
It is interesting to note that the linux driver has lots of special
case code for this chip.
* Some dummynet code incorrectly handled a malloc()-allocated pseudo-mbuf
header structure, called "pkt," and could consequently pollute the mbuf
free list if it was ever passed to m_freem(). The fix involved passing not
pkt, but essentially pkt->m_next (which is a real mbuf) to the mbuf
utility routines.
* Also, for dummynet, in bdg_forward(), made the code copy the ethernet header
back into the mbuf (prepended) because the dummynet code that follows expects
it to be there but it is, unfortunately for dummynet, passed to bdg_forward
as a seperate argument.
PRs: kern/19551 ; misc/21534 ; kern/23010
Submitted by: Thomas Moestl <tmoestl@gmx.net>
Reviewed by: bmilekic
Approved by: luigi
struct sigframe. We need more than only the signal context.
o Properly convert the signal mask when setting up the signal
frame in linux_sendsig and properly convert it back in
linux_sigreturn.
Do some cleanups and improve style while here.
can unload. Doing so leaves the linuxulator in a crippled
state (no ioctl support) when Linux binaries are run at
unload time.
While here, consistently spell ELF in capitals and perform
some minor style improvements.
ELF spelling submitted by: asmodai
is already in 32-bit mode, we need to be able to detect this and still
read the chip ID code. Detecting 32-bit mode is actually a little
tricky, since we want to avoid turning it on accidentally. The easiest
way to do it is to just try and read the PCI subsystem ID from the
bus control registers using 16-bit accesses and compare that with the
value read from PCI config space. If they match, then we know we're in
16-bit mode, otherwise we assume 32-bit mode.
instead of ng_send_data().
The latter could lead to running the IP stack at splimp
instead of splnet, (among other problems) (that MAY be safe
but I wouldn't count on it).
Noticed while preparing a new set of netgraph stuff.
counter register in-CPU.
This is to be used as a fast "timer", where linearity is more important
than time, and multiple lines in the linearity caused by multiple CPUs
in an SMP machine is not a problem.
This adds no code whatsoever to the FreeBSD kernel until it is actually
used, and then as a single-instruction inline routine (except for the
80386 and 80486 where it is some more inline code around nanotime(9).
Reviewed by: bde, kris, jhb
a kevent upon completion of the I/O. Specifically, introduce a new type
of sigevent notification, SIGEV_EVENT. If sigev_notify is SIGEV_EVENT,
then sigev_notify_kqueue names the kqueue that should receive the event
and sigev_value contains the "void *" is copied into the kevent's udata
field.
In contrast to the existing interface, this one: 1) works on
the Alpha 2) avoids the extra copyin() call for the kevent because all
of the information needed is in the sigevent and 3) could be
applied to request a single kevent upon completion of an entire lio_listio().
Reviewed by: jlemon
- move the call to cia_init_sgmap() to after we've determined if we're a pyxis
- convert needed splhigh() in cia_sgmap_invalidate_pyxis() to disable_intr()
Previously, any isa DMA on a pyxis based machine would cause a panic
in cia_sgmap_invalidate_pyxis() because the pyxis workaround was never
setup.
- while i'm at it, convert needed splhigh() in cia_swiz_set_hae_mem to
disable_intr()
in the face of multiple processes doing massive numbers of filesystem
operations. While this patch will work in nearly all situations, there
are still some perverse workloads that can overwhelm the system.
Detecting and handling these perverse workloads will be the subject
of another patch.
Reviewed by: Paul Saab <ps@yahoo-inc.com>
Obtained from: Ethan Solomita <ethan@geocast.com>
could not compress into clusters. This could result in lots of
wasted clusters while recieving small packets from an interface
that uses clusters for all it's packets.
Patch is partially from BSDi (limiting the size of the copy) and
based on a patch for 4.1 by Ian Dowse <iedowse@maths.tcd.ie> and
myself.
Reviewed by: bmilekic
Obtained From: BSDi
Submitted by: iedowse
- Use the mutex in hardclock to ensure no races between it and
softclock.
- Make softclock be INTR_MPSAFE and provide a flag,
CALLOUT_MPSAFE, which specifies that a callout handler does not
need giant. There is still no way to set this flag when
regstering a callout.
Reviewed by: -smp@, jlemon
Removed most of the hacks that were trying to deal with low-memory
situations prior to now.
The new code is based on the concept that I/O must be able to function in
a low memory situation. All major modules related to I/O (except
networking) have been adjusted to allow allocation out of the system
reserve memory pool. These modules now detect a low memory situation but
rather then block they instead continue to operate, then return resources
to the memory pool instead of cache them or leave them wired.
Code has been added to stall in a low-memory situation prior to a vnode
being locked.
Thus situations where a process blocks in a low-memory condition while
holding a locked vnode have been reduced to near nothing. Not only will
I/O continue to operate, but many prior deadlock conditions simply no
longer exist.
Implement a number of VFS/BIO fixes
(found by Ian): in biodone(), bogus-page replacement code, the loop
was not properly incrementing loop variables prior to a continue
statement. We do not believe this code can be hit anyway but we
aren't taking any chances. We'll turn the whole section into a
panic (as it already is in brelse()) after the release is rolled.
In biodone(), the foff calculation was incorrectly
clamped to the iosize, causing the wrong foff to be calculated
for pages in the case of an I/O error or biodone() called without
initiating I/O. The problem always caused a panic before. Now it
doesn't. The problem is mainly an issue with NFS.
Fixed casts for ~PAGE_MASK. This code worked properly before only
because the calculations use signed arithmatic. Better to properly
extend PAGE_MASK first before inverting it for the 64 bit masking
op.
In brelse(), the bogus_page fixup code was improperly throwing
away the original contents of 'm' when it did the j-loop to
fix the bogus pages. The result was that it would potentially
invalidate parts of the *WRONG* page(!), leading to corruption.
There may still be cases where a background bitmap write is
being duplicated, causing potential corruption. We have identified
a potentially serious bug related to this but the fix is still TBD.
So instead this patch contains a KASSERT to detect the problem
and panic the machine rather then continue to corrupt the filesystem.
The problem does not occur very often.. it is very hard to
reproduce, and it may or may not be the cause of the corruption
people have reported.
Review by: (VFS/BIO: mckusick, Ian Dowse <iedowse@maths.tcd.ie>)
Testing by: (VM/Deadlock) Paul Saab <ps@yahoo-inc.com>
Pre-rfork code assumed inherent locking of a process's file descriptor
array. However, with the advent of rfork() the file descriptor table
could be shared between processes. This patch closes over a dozen
serious race conditions related to one thread manipulating the table
(e.g. closing or dup()ing a descriptor) while another is blocked in
an open(), close(), fcntl(), read(), write(), etc...
PR: kern/11629
Discussed with: Alexander Viro <viro@math.psu.edu>
are in softclock() for a long time. The old code already did an
splx()/slphigh() pair here, I just missed adding in the equivalent mutex
operations on sched_lock earlier.
This makes crash recovery work for stripe sizes that are not multiples of
DEFAULT_REVIVE_BLOCKSIZE (currently 64 kB).
While we're here, fix a few cosmetic nits.
Reviewed by: grog
Sponsored by: Enitel ASA (http://www.enitel.no/)
may block on a mutex while on the sleep queue without corrupting
it.
- Move dropping of Giant to after the acquire of sched_lock.
Tested by: John Hay <jhay@icomtek.csir.co.za>
jhb
instead of DIAGNOSTIC.
- Remove the p_wchan check as it no longer applies since a process may be
switched out during CURSIG() within msleep() or mawait().
- Remove an extra sanity check only needed during the early SMPng work.
with Julian and Archie.
Implement a new ``sizedstring'' parse type for dealing with field pairs
consisting of a uint16_t followed by a data field of that size, and use
this to deal with the data_len and data fields.
Written by: Archie with some input by me
Agreed in principle by: julian
untimeout() not being called with Giant in those functions. For now,
use the sched_lock to protect the callout wheel in softclock() and in
the various timeout and callout functions.
Noticed by: tegge
16-bit mode. Technically, pcn_probe() is destructive because once the
chip goes into 32-bit mode, the only way to get it out again is a
hardware reset. And once the device is in 32-bit mode, the lnc driver
won't be able to talk to it. So if pcn_probe() is called before the
lnc probe routine, and pcn_probe() rejects the chip as one it doesn't
support, the lnc driver will be SOL.
I don't like this. I think it's a design flaw that you can't switch
the chip out of 32-bit mode once it's selected. The only 'right'
solution is for the pcn driver to support all of the PCI devices
in 32-bit mode, however I don't have samples of all the PCnet series
cards for testing.
acquire Giant as needed in functions that call mi_switch(). The releases
need to be done outside of the sched_lock to avoid potential deadlocks
from trying to acquire Giant while interrupts are disabled.
Submitted by: witness
linux_rt_sendsig() and restore the same signal mask linux does
in rt_sigreturn(). This gets us saving/restoring all 64-bits of the
linux sigset_t in rt signals.
Reviewed by: marcel
idea to be holding the sched_lock while we are calling it. As such,
release sched_lock before calling CURSIG() in msleep() and mawait() and
reacquire it after CURSIG() returns.
Submitted by: witness
to our native connect(). This is required to deal with the differences
in the way linux handles connects on non-blocking sockets.
This gets the private beta of the Compaq Linux/alpha JDK working
on FreeBSD/alpha
Approved by: marcel
tsleep(). Namely, mawait() takes an extra argument which is a mutex
to drop when going to sleep. Just as with msleep(), if the priority
argument includes the PDROP flag, then the mutex will be dropped and will
not be reacquired when the process wakes up.
- Add in a backwards compatible macro await() that passes in NULL as the
mutex argument to mawait().
except that it uses the MTX_NOSWITCH flag while it releases Giant via
mtx_exit().
- Add a mtx_recursed() primitive. This primitive should only be used on
a mutex owned by the current process. It will return non-zero if the
mutex is recursively owned, or zero otherwise.
- Add two new flags MA_RECURSED and MA_NOTRECURSED that can be used in
conjuction with MA_OWNED to control the assertion checked by mtx_assert().
- Fix some of the KTR tracepoint strings to use %p when displaying the lock
field of a mutex, which is a uintptr_t.
macros which provide the same functionality and are a bit more
efficient, convert use of CIRCLEQ's in netgraph PPP code to TAILQ's.
Reviewed by: Archie Cobbs <archie@dellroad.org>
sched_lock. This is needed for kernel threads that are created before
interrupts are enabled. kthreads created by kld's that are created at
SI_SUB_KLD such as the random kthread.
Tested by: phk
macros which provide the same functionality and are a bit more
efficient, convert use of CIRCLEQ's in resource manager to TAILQ's.
Approved by: Garrett Wollman <wollman@khavrinen.lcs.mit.edu>
is to first write the deleted directory entry to disk, second write
the zero'ed inode to disk, and finally to release the freed blocks
and the inode back to the cylinder-group map. As this ordering
requires two disk writes to occur which are normally spaced about
30 seconds apart (except when memory is under duress), it takes
about a minute from the time that a file is deleted until its inode
and data blocks show up in the cylinder-group map for reallocation.
If a file has had only a brief lifetime (less than 30 seconds from
creation to deletion), neither its inode nor its directory entry
may have been written to disk. If its directory entry has not been
written to disk, then we need not wait for that directory block to
be written as the on-disk directory block does not reference the
inode. Similarly, if the allocated inode has never been written to
disk, we do not have to wait for it to be written back either as
its on-disk representation is still zero'ed out. Thus, in the case
of a short lived file, we can simply release the blocks and inode
to the cylinder-group map immediately. As the inode and its blocks
are released immediately, they are immediately available for other
uses. If they are not released for a minute, then other inodes and
blocks must be allocated for short lived files, cluttering up the
vnode and buffer caches. The previous code was a bit too aggressive
in trying to release the blocks and inode back to the cylinder-group
map resulting in their being made available when in fact the inode
on disk had not yet been zero'ed. This patch takes a more conservative
approach to doing the release which avoids doing the release prematurely.
of the data structures to include new members that weren't defined in the
manual I have.
I opted to use Doug Ambrisko's WEP patches since David Cornejo's patches
did not include the necessary changes to ancontrol(8) to actually enable
and use WEP.
NOTE: I don't currently have access to an Aironet card, so I can't test
any of this. Everything compiles and close scrutiny doesn't reveal any
obvious problems, but Murphy's Law applies. This means I will probably
leave these changes in -current for a bit longer than usual until I'm
sure they work right.
linux_sigset_t by updating the linux_sigframe struct so as to include
linux's "extramask" field. This field contains the upper 32-bits of
the sigset. extramask sits behind a linux_fpstate struct, which I've
defined primarily for padding purposes.
While we're here, define LINUX_NSIG in terms of LINUX_NBPW (32) and
LINUX_NSIG_WORDS (2).
This fixes problems where threaded apps would accumulate a large
number of zombies. This was happening because the exit signal resides
in the upper 32-bits of the sigset and was never getting unmasked by
the manager thread after the first child exited.
PR: misc/18530 (may be related, originator not yet contacted)
Reviewed by: marcel
This allows us to successfully attach early Storage Dimension cards.
Allocate mailboxes for the 742A bellow the 16MB limit. Although these
cards seem to be able to deal with all other types of data anywhere
in a 32bit address space, 24bit addresses are required for mailboxes.
bt_eisa.c:
Add device IDs for all Storage Dimension products I could
find from their web site.
Thanks to Ted Mittelstaed for loaning me the equipment to diagnose
and fix these problems.
anything and it's likely to be faster on alphas.
Also, add EXT_MOD_TYPE for modules that want to add their own ext_type and
are not network drivers (so they don't use EXT_NET_DRV).
The prior version in the tree was repo-copied from Duncan Barclay's
cvs tree.
Also add $FreeBSD$
Submitted by: Duncan Barclay
Committed-via: raylan link with two webgear cards.
boot problems..
However this demands that dangerously dedicated disks use an
offset of at least 10 from the start to not overwrite the
raid config sector on the HPT...
Shutdown the card when a catastrophic error occurs. This quenches
any interrupts stemming from the card.
aic7xxx_inline.h:
Return instead of processing additional interrupt state
after handling a catastrophic error. We now shutdown the
chip in this case in the hopes that the system can live
without this controller. The shutdown process invalidates any
other interrupt state.
aic7xxx.seq:
Only attempt to clear SCSIBUSL on Ultra2 controllers. The
clearing is workaround for a selection timeout bug on U2/U160
controllers and happens to be illegal on aic7770 (EISA/VL)
controllers.
and which indicates that the ext_buf is to be marked READ-ONLY.
Also introduce M_WRITABLE() macro, which will return true if:
* M_RDONLY is _not_ set AND:
* either mbuf has no ext_buf attached OR it has an ext_buf attached but the ref
count is NOT above 1.
sf_bufs (sendfile) are marked M_RDONLY.
Now code determining whether an mbuf's data area is "shared" or not can be
made to use this instead of doing its own (often incorrect) thing.
Submitted by: bmilekic, dwmalone, and Ian Dowse
Reviewed by: dwmalone, jlemon
to determine whether the given mbuf has a cluster (or some other type of
external storage) attached to it.
Note: This code should eventually be made to use M_WRITABLE() to determine
whether or not a copy should be made.
Reviewed by: jlemon
instead.
Also, fix a small set of "avail." If we're setting `avail,' we shouldn't
be re-checking whether m_flags is M_EXT, because we know that it is, as if
it wasn't, we would have already returned several lines above.
Reviewed by: jlemon
whether the given ext_buf is shared.
* Have the sf_bufs be setup with the mbuf subsystem using MEXTADD() with the
two new arguments.
Note: m_pulldown() is somewhat crotchy; the added comment explains the
situation.
Reviewed by: jlemon
could debug processes after the commit that introduced the typo.
Security is good, but security is not always the same as turning things
off :-).
PR: kern/22711
Obtained from: brooks@one-eyed-alien.net
mainly cut-n-pasted from the i386 port, except for the method of setting
the child's stack which is the only MD part of this function.
I've tested with the example apps shipped with the linux threads source
code (ex1-ex6) and with several binary builds of Mozilla.
- No signal translation is needed. Our signals match the OSF/1 signals
- an OSF/1 sigset_t is 64 bits. Make certain to use all 64-bits of it.
We'd previously only used the lower 32 bits. This was mostly harmless
as I don't know of an OSF/1 apps which use any signals > 31. However,
the alpha Linux ABI uses the osf/1 signal routines and threaded linux
apps tyically use signals 32 and 33 to comminicate with the manager
thread, so it is important we preserve the upper 32-bits.
Reviewed by: marcel (at least in principal)
numerous error recovery buglets.
Many thanks to Tor Egge for his assistance in diagnosing problems with
the error recovery code.
aic7xxx.c:
Report missed bus free events using their own sequencer interrupt
code to avoid confusion with other "bad phase" interrupts.
Remove a delay used in debugging. This delay could only be hit
in certain, very extreme, error recovery scenarios.
Handle transceiver state changes correctly. You can now
plug an SE device into a hot-plug LVD bus without hanging
the controller.
When stepping through a critical section, panic if we step
more than a reasonable number of times.
After a bus reset, disable bus reset interupts until we either
our first attempt to (re)select another device, or another device
attemps to select us. This removes the need to busy wait in
kernel for the scsi reset line to fall yet still ensures we
see any reset events that impact the state of either our initiator
or target roles. Before this change, we had the potential of
servicing a "storm" of reset interrupts if the reset line was
held for a significant amount of time.
Indicate the current sequencer address whenever we dump the
card's state.
aic7xxx.reg:
Transceiver state change register definitions.
Add the missed bussfree sequencer interrupt code.
Re-enable the scsi reset interrupt if it has been
disabled before every attempt to (re)select a device
and when we have been selected as a target.
When being (re)selected, check to see if the selection
dissappeared just after we enabled our bus free interrupt.
If the bus has gone free again, go back to the idle loop
and wait for another selection.
Note two locations where we should change our behavior
if ATN is still raised. If ATN is raised during the
presentation of a command complete or disconnect message,
we should ignore the message and expect the target to put
us in msgout phase. We don't currently do this as it
requires some code re-arrangement so that critical sections
can be properly placed around our handling of these two
events. Otherwise, we cannot guarantee that the check of
ATN is atomic relative to our acking of the message in
byte (the kernel could assert ATN).
Only set the IDENTIFY_SEEN flag after we have settled
on the SCB for this transaction. The kernel looks at
this flag before assuming that SCB_TAG is valid. This
avoids confusion during certain types of error recovery.
Add a critical section around findSCB. We cannot allow
the kernel to remove an entry from the disconnected
list while we are traversing it. Ditto for get_free_or_disc_scb.
aic7xxx_freebsd.c:
Only assume that SCB_TAG is accurate if IDENTIFY_SEEN is
set in SEQ_FLAGS.
Fix a typo that caused us to execute some code for the
non-SCB paging case when paging SCBs. This only occurred
during error recovery.
block bitmaps before unmount() completes. They were written using
bdwrite(), so they were normally written less than 32 seconds after
unmount(), but this is too late if the media is removed or the system
is rebooted soon after unmount(). sync()ing before unmount() didn't
help, because ext2fs uses buggy private caching for these blocks --
it doesn't even bdwrite() them until they are uncached or the filesystem
is unmounted. sync()ing after unmount() didn't help, because sync()
only applies to (vnodes for) mounted filesystems.
PR: 22726
As of this patchset, the loader builds (under NetBSD/macppc), boots, interacts
and talks to BOOTP/NFS servers.
(main.c was moved from boot/ofw/libofw to boot/ofw/common but has no revision
history)
Reviewed by: obrien
This brings the loader up to the point where I can compile it under
NetBSD/macppc and have it boot, interact and talk to NFS servers.
sys/boot/ofw/libofw/main.c has been deleted (it has no revision history) and
replaced with sys/boot/ofw/common/main.c
Reviewed by: obrien
device tree and resource manager contents. This is the kernel side of
the upcoming libdevinfo, which will expose this information to userspace
applications in a trivial fashion.
Remove the now-obsolete DEVICE_SYSCTLS code.
syscall compare against a variable sv_minsigstksz in struct
sysentvec as to properly take the size of the machine- and
ABI dependent struct sigframe into account.
The SVR4 and iBCS2 modules continue to have a minsigstksz of
8192 to preserve behavior. The real values (if different) are
not known at this time. Other ABI modules use the real
values.
The native MINSIGSTKSZ is now defined as follows:
Arch MINSIGSTKSZ
---- -----------
alpha 4096
i386 2048
ia64 12288
Reviewed by: mjacob
Suggested by: bde
This code has help us comprehence ACPI spec .
Contributors of this code is as follows(except for FreeBSD commiter):
Yasuo Yokoyama,
Munehiro Matsuda,
and ALL acpi-jp@jp.freebsd.org people.
Thanks.
R.I.P.
for an interrupt to enable/disable from the vector (and GID too, if we
had multiple GIDs)- so, stupidly for now, search for the right mcpcia's
softc so we have the right base address for the bridge CSR to apply
IRQ bit-twiddle's to. Alas- this doesn't yet allow us to run, but it's
the right direction.
Previously we had to include <machine/param.h> or <sys/param.h> bogusly
due to the fact that <sys/socket.h> CMSG macros needed the ALIGN macro,
which was defined in param.h. However, including param.h was a disaster
for namespace pollution.
This solution, as contributed by shin a while ago, fixes it elegantly
by wrapping the definitions around some namespace pollution preventer
definitions.
This patch was long overdue.
This should allow any network programmer to use <sys/socket.h> as
before.
PR: 19971, 20530
Submitted by: Martin Kaeske <MartinKaeske@lausitz.net>
Mark Andrews <Mark.Andrews@nominum.com>
Patch submitted by: shin
Reviewed by: bde
systems.
From the PR:
When 'probe.slot' is PCI_SLOTMAX (== 31) and 'probe.func' is 7,
call to 'pci_cfgread()' here and machine suddenly hangs up.
I don't know why... (or 450GX chipset's bug?)
PR: i386/20379
Submitted by: Masayuki FUKUI <fukui@sonic.nm.fujitsu.co.jp>
comments on the same line like so:
device foo # FooInc Brand NetEther cards
Also, move the wireless NIC cards to their own section.
Add commented out wl driver in wireless section.
Remove obsolete or redundant comments about some of the wireless cards
that used to apply but don't since we've removed 'at foobus'.
There should be no functional changes in this change.
happen when the vm system maps past the end of an object or tries
to map a zero length object, the pmap layer misses the fact that
offsets wrap into negative numbers and we get stuck.
Found by: Joost Pol aka Nohican <nohican@marcella.niets.org>
Submitted by: tegge
When the printer is turned off the pipe write will cause and error,
which causes lpd to close the device and reopen it to clear the error.
After a short while the device will disappear from the bus but lpd will
have opened the ulpt0 port by then. ulpt_status will check for status
without checking the sc->dying flag and panic the kernel when the device
finally disappears from the bus.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
also
- sync with netbsd
- fix a bug that miscalculates tx cell counts when the pointer size isn't 4
tested both ENI and Adaptec cards on both i386 and alpha.
function declared in kern_ktr.c. The only inline checks left are the
checks that compare KTR_COMPILE with the supplied mask and thus should
be optimized away into either nothing or a direct call to ktr_tracepoint().
- Move several KTR-related options to opt_ktr.h now that they are only
needed by kern_ktr.c and not by ktr.h.
- Add in the ktr_verbose functionality if KTR_EXTEND is turned on. If the
global variable 'ktr_verbose' is non-zero, then KTR messages will be
dumped to the console. This variable can be set by either kernel code
or via the 'debug.ktr_verbose' sysctl. It defaults to off unless the
KTR_VERBOSE kernel option is specified in which case it defaults to on.
This can be useful when the machine locks up spinning in a loop with
interrupts disabled as you might be able to see what it is doing when it
locks up.
Requested by: phk
interface. In addition to using newbus, it also uses bus_space rather
than inb/outb to make it MI. The grody static softc allocation stuff
has been removed as well.
When restarting the sequencer, ensure that the SCBCNT register
is 0. A non-zero count will prevent the setting of the CCSCBDIR
bit in any future dma operations. The only time CCSCBCNT would
be non-zero is if we happened to halt the dma during a reset,
but even that should never happen. Better safe than sorry.
When a command completes before the target responds to an
ATN for a recovery command, we now notify the kernel so that
any recovery operation requeued in the qinfifo can be removed
safely. In the past, we did this in ahc_done(), but ahc_done()
may be called without the card paused. This also avoids a
recursive call to ahc_search_qinifo() which could have occurred if
ahc_search_qinififo() happened to be the routine to complete
a recovery action.
Fix 8bit math used for adjusting the qinfifo. The index must
be wrapped properly within the 256 entry array. We rely on the
fact that qinfifonext is a uint8_t in most cases to handle
this wrap, but we missed a few spots where the resultant
calculation was promoted to an int.
Change the way that we deal with aborting the first or second
entry from the qinfifo. We now swap the first entry in the
qinfifo with the "next queued scb" to force the sequencer
to see an abort collision if we ever touch the qinififo while
the sequencer is mid SCB dma.
aic7xxx.reg:
Add new MKMSG_FAILED sequencer interrupt. This displaced
the BOGUS_TAG interrupt used in some previous sequencer code
debugging.
aic7xxx.seq:
Increment our position in the qinfifo only once the dma
is complete and we have verified that the queue has not
been changed during our DMA. This simplifies code in the
kernel.
Protect against "instruction creep" when issuing a pausing
sequencer interrupt. On at least the 7890/91/96/97, the
sequencer will coast after issuing the interrupt for up
to two instructions. In the past we delt with this by
using carefully placed nops. Now we call a routine to
issue the interrupt followed by a nop and a ret.
Tell the kernel should an SCB complete with the MK_MESSAGE
flag still set. This means the target ignored our ATN request.
Clear the channel twice as we exit the data phase. On the
aic7890/91, the S/G preload logic may require the second
clearing to get the last S/G out of the FIFO.
aic7xxx_freebsd.c:
Don't bother searching the qinfifo for a doubly queued
recovery scb in ahc_done. This case is handled by the
core driver now.
Free the path used to issue async callbacks after the callback
is complete.
aic7xxx_inline.h:
Split the SCB queue routine into a routine that swaps
the SCB with the "next queued SCB" and a routine that
calls the swapping routine and notifies the card of
the new SCB. The swapping routine is now also used by
ahc_search_qinfifo.
The offset field in struct dirent was set to the offset of
the next dirent in rev 1.36. The offset was calculated from
the current offset and the record length. This offset does
not necessarily match the real offset when we are using
cookies. Therefore, also use the cookies to set the offset
field in struct dirent if we're using cookies to iterate
through the dirents.
circuit generates too much jitter to be used directly as xmit clock.
Don't miscount pending bytes in weird error conditions.
Drop the rest of a packet if we run out of tx-md's.
Trig the xmit-frame signal on rising edge, this fixed the one-bit-too-late
position of the HDLC frames in E1 mode.
wakeup all of the sleeping threads when we free only one buffer. This
avoids us having to needlessly try again (and fail, and go back to
sleep) for all the threads sleeping. We will now only wakeup the
thread we know will succeed.
Reviewed by: green
only be checked if the system is currently performing New Reno style
fast recovery. However, this value was being checked regardless of the
NR state, with the end result being that the congestion window was never
opened.
Change the logic to check t_dupack instead; the only code path that
allows it to be nonzero at this point is NewReno, so if it is nonzero,
we are in fast recovery mode and should not touch the congestion window.
Tested by: phk
pollution in <sys/mutex.h>. This was half fixed in rev.1.3 of
midwayreg.h. The pollution exposed the bug that this driver was using
toy versions of the bus space macros under FreeBSD. Disabling the
toy versions made this driver compile but dependent on the pollution.
There was still a toy version of bus_space_read_1() in unreachable code.
namespace pollution in <sys/mutex.h>. This was half fixed in rev.1.3
of midwayreg.h. The pollution exposed the bug that this driver was
using toy versions of the bus space macros under FreeBSD. Disabling
the toy versions made this driver compile and maybe support PIO space,
but dependent on the pollution.
ufs_vnops.c:
1) i_ino was confused with i_number, so the inode number passed to
VFS_VGET() was usually wrong (usually 0U).
2) ip was dereferenced after vgone() freed it, so the inode number
passed to VFS_VGET() was sometimes not even wrong.
Bug (1) was usually fatal in ext2_mknod(), since ext2fs doesn't have
space for inode 0 on the disk; ino_to_fsba() subtracts 1 from the
inode number, so inode number 0U gives a way out of bounds array
index. Bug(1) was usually harmless in ufs_mknod(); ino_to_fsba()
doesn't subtract 1, and VFS_VGET() reads suitable garbage (all 0's?)
from the disk for the invalid inode number 0U; ufs_mknod() returns
a wrong vnode, but most callers just vput() it; the correct vnode is
eventually obtained by an implicit VFS_VGET() just like it used to be.
Bug (2) usually doesn't happen.
freelist. Should now be thread-friendly, in part.
Note: More work is needed in uipc_syscalls.c, but it will have to wait until
the socket locking issues are at least 80% implemented and committed.
CDs.
With audio CDs, you can't just do a READ(10) call on most drives without
first setting the blocksize with a mode select command. The disklabel code
does a read of the first sector of the media to find a label if it exists.
This caused drives to return an error when an audio CD was in the drive,
due to the problem described above.
The solution is to read the table of contents on the CD, and only attempt
to read the disklabel if the first track is a data track.
This works on all the various CD and DVD media I have tried, but further
testing (especially with Video CDs and other mode 2 media) will be
needed to determine if this is a universal solution.
When this feature is enabled, mke2fs doesn't necessarily allocate a
super block and its associated descriptor blocks for every group.
The (non-)allocations are reflected in the block bitmap. Since the
filesystem code doesn't write to these blocks except for the first
superblock, all it has to do to support them is to not count them in
ext2_statfs() and not attempt to check them at mount time in
ext2_check_blocks_bitmap() (the check has never been enabled in
FreeBSD anyway).
and nobroadcast bits in the mode register and call it both from
pcn_init() and pcn_ioctl(). Sometimes we need to force the state
of the nobroadcast bit after switching out of promisc mode.
them. If we leave garbage in them, the dc_apply_fixup() routine may
try to follow bogus pointers when applying the reset fixup.
Noticed by: Andrew Gallatin
getnewvnode(). Otherwise routines called from VOP_INACTIVE() might
attempt to remove the vnode from a free list the vnode isn't on,
causing corruption.
PR: 18012
out of fashion. This particular case, unlike joy(8) and friends which
are just plain silly, did more than just load a kernel loadable module.
However, /etc/rc and the linux_base port were adjusted a while back to
cope with the absence of this script.
The only outstanding reason to hang on to it would have been for the
linux(8) manual page, which clued folks into the existence of the
Linuxulator. A new linux(4) was introduced a while back. It does
a much better job.
This script just isn't useful any more.
- Look for a hardwired interrupt in the routing table for this
bus/device/pin (we already did this).
- Look for another device with the same link byte which has a hardwired
interrupt.
- Look for a PCI device matching an entry with the same link byte
which has already been assigned an interrupt, and use that.
- Look for a routable interrupt listed in the "PCI only" interrupts
field and use that.
- Pick the first interrupt that's marked as routable and use that.
Xtal reference instead of the CLADI input.
In unframed E1 mode, tie SIGFRZ low so that the mysycc doesn't
get confused.
Don't mask errors with OOF. Don't ignore OOF errors.
Stop the channel before freeing mbufs in disconnect.
I still have no T1 devices to test with, so the T1 code is non-existent.
argument. These flags include INTR_FAST, INTR_MPSAFE, etc.
- Properly handle INTR_EXCL when it is passed in to allow an interrupt
handler to claim exclusive ownership of an interrupt thread.
- Add support for psuedo-fast interrupts on the alpha. For fast interrupts,
we don't allocate an interrupt thread; instead, during dispatching of an
interrupt, we run the handler directly instead of scheduling the thread
to run. Note that the handler is currently run without Giant and must be
MP safe. The only fast handler currently is for the sio driver.
Requested by: dfr
multicast filter on the Pegasus chip. Since IPv6 depends a lot
on multicasting, this caused several failures for people trying to
use IPv6 with Pegasus USB ethernet devices.
Submitted by: Jun Kuriyama <kuriyama@FreeBSD.org>
Return ENOTSUP for any opcode that is not supported by the XPT
device.
Add back a missing local declaration that seems to have been deleted
by my last commit.
Filter incoming transfer negotiation requests to ensure they
never exceed the settings specified by the user.
In restart sequencer attempt to deal with a bug in the aic7895.
If a third party reset occurs at just the right time, the
stack register can lock up. When restarting the sequencer
after handling the SCSI reset, poke SEQADDR1 before resting
the sequencers program counter.
When something strange happens, dump the card's transaction
state via ahc_dump_card_state(). This should aid in debugging.
Handle request sense transactions via the QINFIFO instead of
attaching them to the waiting queue directly. The waiting
queue consumes card SCB resources and, in the pathological case
of every target on the bus beating our selection attemps and
issuing a check condition, could have caused us to run out
of SCBs. I have never seen this happen, and only early
cards with 3 or 4 SCBs had any real chance of ever getting
into this state.
Add additional sequencer interrupt codes to support firmware
diagnostics. The diagnostic code is enabled with the
AHC_DEBUG_SEQUENCER kernel option.
Make it possible to switch into and out of target mode on
the fly. The card comes up by default as an initiator but
will switch into target mode as soon as an enable lun operation
is performed. As always, target mode behavior is gated
by the AHC_TMODE_ENABLE kernel option so most users will
not be affected by this change.
In ahc_update_target_msg_request(), also issue a new
request if the ppr_options have changed.
Never issue a PPR as a target. It is forbidden by the spec.
Correct a bug in ahc_parse_msg() that prevented us from
responding to PPR messages as a target.
Mark SCBs that are on the untagged queue with a flag instead
of checking several fields in the SCB to see if the SCB should
be on the queue. This makes it easier for things like automatic
request sense requests to be queued without touching the
untagged queues even though they are untagged requests.
When dealing with ignore wide residue messages that occur
in the middle of a transfer, reset HADDR, not SHADDR for
non-ultra2 chips. Although SHADDR is where the firmware
fetches the ending transfer address for a save data pointers
request, it is readonly. Setting HADDR has the side effect
of also updating SHADDR.
Cleanup the output of ahc_dump_card_state() by nulling out the
free scb list in the non-paging case. The free list is only
used if we must page SCBs.
Correct the transmission of cdbs > 12 bytes in length. When
swapping HSCBs prior to notifing the sequencer of the new
transaction, the bus address pointer for the cdb must also
be recalculated to reflect its new location. We now defer
the calculation of the cdb address until just before queing
it to the card.
When pulling transfer negotiation settings out of scratch
ram, convert 5MHz/clock doubled settings to 10MHz.
Add a new function ahc_qinfifo_requeue_tail() for use by
error recovery actions and auto-request sense operations.
These operations always occur when the sequencer is paused,
so we can avoid the extra expense incurred in the normal
SCB queue method.
Use the BMOV instruction for all single byte moves on
controllers that support it. The bmov instruction is
twice as fast as an AND with an immediate of 0xFF as
is used on older controllers.
Correct a few bugs in ahc_dump_card_state(). If we have
hardware assisted queue registers, use them to get the
sequencer's idea of the head of the queue. When enumerating
the untagged queue, it helps to use the correct index for
the queue.
aic7xxx.h:
Indicate via a feature flag, which controllers can take
on both the target and the initiator role at the same time.
Add the AHC_SEQUENCER_DEBUG flag.
Add the SCB_CDB32_PTR flag used for dealing with cdbs
with lengths between 13 and 32 bytes.
Add new prototypes.
aic7xxx.reg:
Allow the SCSIBUSL register to be written to. This is
required to fix a selection timeout problem on the 7892/99.
Cleanup the sequencer interrupt codes so that all debugging
codes are grouped at the end of the list.
Correct the definition of the ULTRA_ENB and DISC_DSB locations
in scratch ram. This prevented the driver from properly honoring
these settings when no serial eeprom was available.
Remove an unused sequencer flag.
aic7xxx.seq:
Just before a potential select-out, clear the SCSIBUSL
register. Occasionally, during a selection timeout, the
contents of the register may be presented on the bus,
causing much confusion.
Add sequencer diagnostic code to detect software and or
hardware bugs. The code attempts to verify most list
operations so any corruption is caught before it occurs.
We also track information about why a particular reconnection
request was rejected.
Don't clobber the digital REQ/ACK filter setting in SXFRCTL0
when clearing the channel.
Fix a target mode bug that would cause us to return busy
status instead of queue full in respnse to a tagged transaction.
Cleanup the overrun case. It turns out that by simply
butting the chip in bitbucket mode, it will ack any
bytes until the phase changes. This drasticaly simplifies
things.
Prior to leaving the data phase, make sure that the S/G
preload queue is empty.
Remove code to place a request sense request on the waiting
queue. This is all handled by the kernel now.
Change the semantics of "findSCB". In the past, findSCB
ensured that a freshly paged in SCB appeared on the disconnected
list. The problem with this is that there is no guarantee that
the paged in SCB is for a disconnected transation. We now
defer any list manipulation to the caller who usually discards
the SCB via the free list.
Inline some busy target table operations.
Add a critical section to protect adding an SCB to
the disconnected list.
aic7xxx_freebsd.c:
Handle changes in the transfer negotiation setting API
to filter incoming requests. No filtering is necessary
for "goal" requests from the XPT.
Set the SCB_CDB32_PTR flag when queing a transaction with
a large cdb.
In ahc_timeout, only take action if the active SCB is
the timedout SCB. This deals with the case of two
transactions to the same device with different timeout
values.
Use ahc_qinfifo_requeu_tail() instead of home grown
version.
aic7xxx_inline.h:
Honor SCB_CDB32_PTR when queuing a new request.
aic7xxx_pci.c:
Use the maximum data fifo threshold for all chips.
The XPT uses this to prevent tags from being used on parallel SCSI
interfaces immediately after a bus reset or BDR so that controllers
have an oportunity to renegotiate without tag messages in the way.
Somehow this got disabled... the functionality has been here for
quite some time.
Noticed by: my SCSI bus analyzer
This removes support for booting current kernels with very old bootblocks.
Device driver writers: Please remove initializations for the d_bmaj
field in your cdevsw{}.
terminated and the data_len field is no longer necessary.
Add ASCII2BINARY and BINARY2ASCII capabilities.
The old format is still understood and dealt with, but can't do
the ASCII2BINARY and BINARY2ASCII stuff.
Approved by: archie
current implementation, jail neither virtualizes the Sys V IPC namespace,
nor provides inter-jail protections on IPC objects.
o Support for System V IPC can be enabled by setting jail.sysvipc_allowed=1
using sysctl.
o This is not the "real fix" which involves virtualizing the System V
IPC namespace, but prevents processes within jail from influencing those
outside of jail when not approved by the administrator.
Reported by: Paulo Fragoso <paulo@nlink.com.br>
in the p_candebug() function. Synchronize with sef's CHECKIO()
macro from the old procfs, which seems to be a good source of security
checks.
Obtained from: TrustedBSD Project
PPTP links are no longer dropped by simple (and inappropriate in this
case) "inactivity timeout" procedure, only when requested through the
control connection.
It is now possible to have multiple PPTP servers running behind NAT.
Just redirect the incoming TCP traffic to port 1723, everything else
is done transparently.
Problems were reported and the fix was tested by:
Michael Adler <Michael.Adler@compaq.com>,
David Andersen <dga@lcs.mit.edu>
This is due to a bug that has been in there since Warneer did the
PCCARD stuff, the altioaddr is not offset 8 its offset 14 from
the base address.
Also only probe the master device, no known PCCARD ATA thingies
has a slave AFAIK..
- Add DRIVER_MODULE() declaration to make this driver a
child of cardbus
- Handle different width EEPROMs
The CIS parser still barfs when scanning this card, but it seems to
probe/attach correctly anyway. I can't do a traffic test just yet
since I don't have a proper crossover cable handy.
This allows writing to DVD-RAM, PD and similar drives that probe as CD
devices. Note that these are randomly writeable devices, not
sequential-only devices like CD-R drives, which are supported by cdrecord.
Add a new flag value for dsopen(), DSO_COMPATLABEL. The cd(4) driver now
uses this flag instead of the DSO_NOLABELS flag. The DSO_NOLABELS always
used a "fake" disklabel for the entire disk, provided by the caller.
With the DSO_COMPATLABEL flag, dsopen() will first search the media for a
label, and if it finds a label, it will use that label. Otherwise it will
use the fake disklabel provided by the caller. This provides backwards
compatibility, since we will still have labels for ISO9660 media.
It also provides new functionality, since you can now have a regular BSD
disklabel on read-only media, or on writeable media (e.g. DVD-RAM).
Bruce and I both think that we should eventually (in a few years) get
away from using disklabels for ISO9660 media, and just use the whole disk
device (/dev/cd0). At that point disklabel handling in the cd(4) driver
could follow the "normal" model, as used in the da(4) driver.
Also, clean up the path in a couple of places in cdregister(). (Thanks to
Nick Hibma for catching that bug.)
Reviewed by: bde
Otherwise, aio_read() and aio_write() on sockets are broken if a kevent is
registered. (The code after kevent registration for handling sockets assumes
that the struct file pointer "fp" still refers to the socket, not the kqueue.)
Don't check for a null pointer if malloc called with M_WAITOK.
Submitted by: josh@zipperup.org
Submitted by: Robert Drehmel <robd@gmx.net>
Approved by: bp
<sys/proc.h> to <sys/systm.h>.
Correctly document the #includes needed in the manpage.
Add one now needed #include of <sys/systm.h>.
Remove the consequent 48 unused #includes of <sys/proc.h>.
the offending inline function (BUF_KERNPROC) on it being #included
already.
I'm not sure BUF_KERNPROC() is even the right thing to do or in the
right place or implemented the right way (inline vs normal function).
Remove consequently unneeded #includes of <sys/proc.h>
used in lower layer (scsi_low.c).
The flag of ncv for KME KXLC004 was chaged from 0x1 to 0x100.
The flag of nsp for PIO mode was chaged from 0x1 to 0x100.
command register is too aggressive. Revert to the previous behaviour, but
leave the new behaviour available as an undocumented option. It's not
clear what the Right, Right Thing is to do here, but the more conservative
approach is safer.
a RealTek 8139 cardbus device. Unfortunately it doesn't quite work yet
because the CIS parser barfs on it.
Submitted by msmith, with some small tweaks by me.
return the last value returned by a nested method call. This violates
the ACPI spec, but is implemented by the Microsoft interpreter, and thus
vendors can (and do) get away with it.
Intel's stance is that this is illegal and should not be supported.
As they put it, however, we have to live in the real world. So go ahead
and implement it.
Submitted by: Mitsaru IWASAKI <iwasaki@jp.freebsd.org>
- Set debugger options for kernel build
- Define some missing functions
- Bring in GCC defines
- Disable the 'wbinvd' macro as it conflicts with our inline
- AcpiGetProcessorID (fetch the ACPI processor ID for a given ACPI_HANDLE)
- AcpiSetSystemSleepState (set the Sx sleeping state, proposed by Intel
but not actually implemented)
ACPICA. Most of these are still works in progress. Support exists for:
- Fixed feature and control method power, lid and sleep buttons.
- Detection of ISA PnP devices using ACPI namespace.
- Detection of PCI root busses using ACPI namespace.
- CPU throttling and sleep states (incomplete)
- Thermal monitoring and cooling control (incomplete)
- Interface to platform embedded controllers (mostly complete)
- ACPI timer (incomplete)
- Simple userland control of sleep states.
- Shutdown and poweroff.
