Most keyboard drivers are using the genkbd implementations as it is;
formally use them for any that aren't set and make
genkbd_get_fkeystr/genkbd_diag private.
These invocations were directly calling enkbd_diag(), rather than
indirection back through kbdd_diag/kbdsw. While they're functionally
equivent, invoking kbdd_diag where feasible (i.e. not in a diag
implementation) makes it easier to visually identify locking needs in these
other drivers.
The datasheets for these chips claim the maximum is 921,600, but testing
shows these two higher rates also work (but no rates above 921,600 other
than these two work; these represent dividing the base buad clock by 3 and 2
respectively).
o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.
Some places in network code may need to verify that an ethernet address
is not the 'zero' address. Provide a standard macro ETHER_IS_ZERO for
this purpose, similar to the ETHER_IS_BROADCAST macro already available.
This patch also removes previous ETHER_IS_ZERO definitions in several
USB ethernet drivers, in favor of this centrally-located macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed by: erj@
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D21240
When epoch(9) was introduced to network stack, it was basically
dropped in place of existing locking, which was mutexes and
rwlocks. For the sake of performance mutex covered areas were
as small as possible, so became epoch covered areas.
However, epoch doesn't introduce any contention, it just delays
memory reclaim. So, there is no point to minimise epoch covered
areas in sense of performance. Meanwhile entering/exiting epoch
also has non-zero CPU usage, so doing this less often is a win.
Not the least is also code maintainability. In the new paradigm
we can assume that at any stage of processing a packet, we are
inside network epoch. This makes coding both input and output
path way easier.
On output path we already enter epoch quite early - in the
ip_output(), in the ip6_output().
This patch does the same for the input path. All ISR processing,
network related callouts, other ways of packet injection to the
network stack shall be performed in net_epoch. Any leaf function
that walks network configuration now asserts epoch.
Tricky part is configuration code paths - ioctls, sysctls. They
also call into leaf functions, so some need to be changed.
This patch would introduce more epoch recursions (see EPOCH_TRACE)
than we had before. They will be cleaned up separately, as several
of them aren't trivial. Note, that unlike a lock recursion the
epoch recursion is safe and just wastes a bit of resources.
Reviewed by: gallatin, hselasky, cy, adrian, kristof
Differential Revision: https://reviews.freebsd.org/D19111
Create an attachment file for the existing ACPI attachment, and create a
new FDT attachment for the generic-ehci driver.
Submitted by: andrew (Original version)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D19389
above 1Kbyte. It might look like some XHCI(4) controllers do not
support when the USB control transfer is split using a link TRB. The
next NORMAL TRB after the link TRB is simply failing with XHCI error
code 4. The quirk ensures we allocate a 64Kbyte buffer so that the
data stage TRB is not broken with a link TRB.
Found at: EuroBSDcon 2019
MFC after: 1 week
Sponsored by: Mellanox Technologies
libusb. This is useful for speeding up large data transfers while reducing
the interrupt rate.
Found at: EuroBSDcon 2019
MFC after: 1 week
Sponsored by: Mellanox Technologies
this to 2k to prevent them from being truncated and ignored. It
appears to be a sanity check only, but bumping it to 2k allows both of
my iic hid devices to be parsed and the second one to work...
After r351243 when ALTQ was enabled in the kernel, the inline functions
in ifq.h would not have full type information as if_var.h was not
included.
Given usb_ethernet.h already includes all the various headers (which)
is the cause of the problem here, add if_var.h to it. This fixes the
builds again.
Reported by: CI system, e.g. FreeBSD-head-aarch64-LINT
order to have struct mii_data available. However, it only really needs
a forward declaration of struct mii_data for use in pointer form for
the return type of a function prototype.
Custom kernel configuration that have usb and fdt enabled, but no miibus,
end up with compilation failures because miibus_if.h will not get
generated.
Due to the above, the following changes have been made to usb_ethernet.h:
* remove the inclusion of mii headers
* forward-declare struct mii_data
* include net/ifq.h to satify the need for complete struct ifqueue
Reviewed by: ian
Obtained from: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D21293
with Communication Device Class Ethernet Emulation Model (CDC EEM).
The driver supports both the device, and host side operation; there
is a new USB template (#11) for the former.
This enables communication with virtual USB NIC provided by iLO 5,
as found in new HPE Proliant servers.
Reviewed by: hselasky
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Hewlett Packard Enterprise
Enable this for the NovAtel OEMv2 GPS receiver.
Not fixed: The receiver shows up as "<Interface 0>" in the device
tree, because that is literally what the descriptor-string is.
Reviewed by: hselasky@
While at it fix an invalid memory access issue when attaching external
USB HUBs, which are not mapped by ACPI, due to missing status check
when calling AcpiGetObjectInfo() from acpi_usb_hub_port_probe_cb().
Sponsored by: Mellanox Technologies
