Allow new enclosure to replace previously existing one if there is
no completely unused table entry, same as it is done for devices.
If we can not process DPM due to corruption -- wipe it and restart
from scratch. Otherwise I don't see a way to recover persistence if
something go wrong and there is no BIOS to recover it for us.
Together this solves a problem that appeared when 9300-8i firmware
update to 16.00.10.00 somehow switched its mapping mode from Device
Persistence to Enclosure/Slot without wiping the DPM table. It made
HBA completely unusable, since overflowed and conflicting mapping
table was unable to map any of enclosures and so devices.
Also while there make some enclosure mapping errors more informative.
MFC after: 1 month
Sponsored by: iXsystems, Inc.
This fixes mpr driver on big-endian devices.
Tested on powerpc64 and powerpc64le targets using a SAS9300-8i card
(LSISAS3008 pci vendor=0x1000 device=0x0097)
Submitted by: Andre Fernando da Silva <andre.silva@eldorado.org.br>
Reviewed by: luporl, alfredo, Sreekanth Reddy <sreekanth.reddy@broadcom.com> (by email)
Sponsored by: Eldorado Research Institute (eldorado.org.br)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D25785
Uses of mallocarray(9).
The use of mallocarray(9) has rocketed the required swap to build FreeBSD.
This is likely caused by the allocation size attributes which put extra pressure
on the compiler.
Given that most of these checks are superfluous we have to choose better
where to use mallocarray(9). We still have more uses of mallocarray(9) but
hopefully this is enough to bring swap usage to a reasonable level.
Reported by: wosch
PR: 225197
Focus on code where we are doing multiplications within malloc(9). None of
these is likely to overflow, however the change is still useful as some
static checkers can benefit from the allocation attributes we use for
mallocarray.
This initial sweep only covers malloc(9) calls with M_NOWAIT. No good
reason but I started doing the changes before r327796 and at that time it
was convenient to make sure the sorrounding code could handle NULL values.
sys/dev/mpr/mpr_mapping.c
If _mapping_process_dpm_pg0 detects inconsistencies in the drive
mapping table (stored in the HBA's NVRAM), abort reading it and
continue to boot as if the mapping table were blank. I observed
such inconsistencies in several HBAs after upgrading firmware from
14.0.0.0 to 15.0.0.0.
Reviewed by: slm
MFC after: 3 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D12901
commit it to make initiazation less chatty in the normal case, and more useful
and informative when real debugging is turned on.
Reviewed by: ken (earlier version)
Sponsored by: Netflix
This includes NVMe device support and adds support for the following adapters:
SAS 3408
SAS 3416
SAS 3508
SAS 3516
SAS 3616
SAS 3708
SAS 3716
Reviewed by: ken, scottl, asomers, mav
Approved by: ken, scottl, mav
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D10095
- Updated all files with 2015 Avago copyright, and updated LSI's copyright
dates.
- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).
- Added a sysctl variable to control how StartStopUnit behavior works. User can
select to spin down disks based on if disk is SSD or HDD.
- Inquiry data is required to tell if a disk will support SSU at shutdown or
not. Due to the addition of mpssas_async, which gets Advanced Info but not
Inquiry data, the setting of supports_SSU was moved to the
mpssas_scsiio_complete function, which snoops for any Inquiry commands. And,
since disks are shutdown as a target and not a LUN, this process was
simplified by basing it on targets and not LUNs.
- Added a sysctl variable that sets the amount of time to retry after sending a
failed SATA ID command. This helps with some bad disks and large disks that
require a lot of time to spin up. Part of this change was to add a callout to
handle timeouts with the SATA ID command. The callout function is called
mpssas_ata_id_timeout(). (Fixes PR 191348)
- Changed the way resets work by allowing I/O to continue to devices that are
not currently under a reset condition. This uses devq's instead of simq's and
makes use of the MPSSAS_TARGET_INRESET flag. This change also adds a function
called mpssas_prepare_tm().
- Some changes were made to reduce code duplication when getting a SAS address
for a SATA disk.
- Fixed some formatting and whitespace.
- Bump version of mps driver to 9.255.01.00-fbsd
PR: 191348
Reviewed by: ken, scottl
Approved by: ken, scottl
MFC after: 1 week
message synced to the changes in r283632, those changes are now backed out.
Another commit will be done that is exactly the same as r283632 except it will
have to correct commit message.
Approved by: ken, scottl, asomers, gibbs
This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.
Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.
o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.
o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.
Thanks to LSI for developing and testing this driver for FreeBSD.
share/man/man4/mpr.4:
mpr(4) man page.
sys/dev/mpr/*:
mpr(4) driver files.
sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.
sys/conf/files:
Add the mpr(4) driver.
sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.
sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.
sys/i386/conf/XEN:
Exclude the mpr module from building here.
Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added
