There was a race that bridge_ifdetach() could be called via
ifnet_departure event handler after vnet_bridge_uninit().
PR: 195859
Reported by: Danilo Egea Gondolfo
interrupts are enabled and the NIC is awake (think: loading a module)
then there's a not-quite-zero window where we'll get an interrupt
for the device before the attach method is called to finish setting
up the hardware.
Since I grab locks in ath_intr() to check various things, the locks
need to be ready much earlier.
- Use IEEE80211_F_DATAPAD;
- (c->ic_flags & IEEE80211_CHAN_PASSIVE) -> IEEE80211_IS_CHAN_PASSIVE(c);
- Convert ackfailcnt to int (there is dereference to *(int *) in ieee80211_ratectl_tx_complete());
- Fix & move cleanup to the end in wpi_rx_done();
- Add missed lock in wpi_update_beacon();
- Try to fix powersave.
PR: kern/197143
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
includes the shared page allowing debuggers to use the signal trampoline
code to identify signal frames in core dumps.
Differential Revision: https://reviews.freebsd.org/D1828
Reviewed by: alc, kib
MFC after: 1 week
- vfs.recycles counts the number of vnodes forcefully recycled to avoid
exceeding kern.maxvnodes.
- vfs.vnodes_created counts the number of vnodes created by successful
calls to getnewvnode().
Differential Revision: https://reviews.freebsd.org/D1671
Reviewed by: kib
MFC after: 1 week
The QCA9565 can have RFKILL on GPIO Pin 11, and thus we need to configure
it up correctly or the NIC may not function.
I'm not sure why the AR9382 can't use GPIO 8 / GPIO 11 ; it's likely
hooked up to some external LNA or filter. The real solution is to
make it only block pin 8 / pin 11 for AR9382, but the AR9382 probes
like an AR9380. Sigh.
Submitted by: Anthony Jenkins <scoobi_doo@yahoo.com>
redirection support. Older versions of the hypervisor mis-interpret
the cpuid format in ioapic registers when x2APIC is turned on, but IR
is not used by the guest OS.
Based on: Linux commit 4cca6ea04d31c22a7d0436949c072b27bde41f86
Tested by: markj
Sponsored by: The FreeBSD Foundation
MFC after: 2 months
I've been sitting on this for a year or so now; I've finally
tested it on enough devices to be reasonably sure it won't
cause too much drama. But, if you see issues, please email me.
Tested (all STA mode):
PCIe:
* AR9380
* AR9390
* AR9580
* AR9462
* AR9485
SoC:
* QCA9550
* AR9331
* AR9342
especially on native monitor resolutions. This one essentially matches X11
default pointer.
Differential Revision: https://reviews.freebsd.org/D1801
No objection from: emaste
Approved by: adrian, dumbbell
o Ensure we use correct bank for MSK register
o Save and restore current bank in interrupt handler
o Stop TX watchdog on fatal errors
o Use right register for EPH status
This fixes operation on ARMv8 Foundation Model
Reviewed by: benno@
This change by 2-3 times improves performance of misaligned XCOPY and WUT
commands by avoiding unneeded read-modify-write cycles inside ZFS.
MFC after: 1 week
code in my last commit. The cc_exec_next is used to track the next
when a direct call is being made from callout. It is *never* used
in the in-direct method. When macro-izing I made it so that it
would separate out direct/vs/non-direct. This is incorrect and can
cause panics as Peter Holm has found for me (Thanks so much Peter for
all your help in this). What this change does is restore that behavior
but also get rid of the cc_next from the array and instead make it
be part of the base callout structure. This way no one else will get
confused since we will never use it for non-direct.
Reviewed by: Peter Holm and more importantly tested by him ;-)
MFC after: 3 days.
Sponsored by: Netflix Inc.
This change by 2-3 times improves performance of misaligned WRITE SAME
commands by avoiding unneeded read-modify-write cycles inside ZFS.
MFC after: 1 week
VT-d specification. Also add definitions for the interrupt remapping
table and IEC.
Print new capabilities on boot. although there is no hardware which
support it.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
When building some of the boot loaders with clang, and DEBUG_FLAGS or
CFLAGS having '-g' in it, clang outputs several assembly directives that
are too new for our version of binutils.
Therefore, assemble the resulting .s files with clang instead. A more
general solution can be implemented when a GNU as-compatible driver for
clang's integrated assembler appears.
Tested by: gjb
unmount, which causes error from nmount(2) call when performing
MNT_DELEXPORT over the directory which ceased to be a mount point.
The race is legitimate and innocent, but results in the chatty mountd.
Silence it by providing an distinguished error code for the situation,
and ignoring the error in mountd loop.
Based on the patch by: Andreas Longwitz <longwitz@incore.de>
Prodded and tested by: bdrewery
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Switch the cache line size during invalidations/flushes
to be read from CP15 cache type register.
Submitted by: Wojciech Macek <wma@semihalf.com>
Reviewed by: ian, imp
Obtained from: Semihalf
endpoint less frequently to make the sample rate adjustment more
accurate. This should resolve problems with the DN32-USB module for
Midas audio systems and possibly other similar products from Klark
Teknik.
MFC after: 3 days
This port failed to gain traction and probably only a couple Wii consoles
ran FreeBSD all the way to single user mode with an md(4). IPC
support was never implemented, so it was impossible to use any peripheral
Any further development, if any, will happen at https://github.com/rpaulo/wii.
Discussed with: nathanw (a long time ago), jhibbits
