warning message and attach without setting the Ethernet address to a
random address. It is not believed that this code can actually be
executed, and if it does, we're better off printing an error message than
faking up an Ethernet address.
PR: kern/133239
Reviewed by: yongari (earlier version of patch)
Approved by: ed (mentor)
EEPROM on ST201 always returns 16bits data with little endian
format so conversion to host order is required.
This change fixes inversed ethernet address on sparc64.
command in the usb_msctest routines, as well as a general tidyup.
This now properly ejects the ZTE MF636, Option Gi0322 and Novatel MC950D
devices I have on my desk.
pci_delete_child() function called by the cardbus driver. The new function
uses resource_list_unreserve() to release the BARs decoded by the device
being removed.
Reviewed by: imp
Tested by: brooks
This should fix some Thinkpad specific problems such as
connecting to a headphone jack is not functional on X41.
Reviewed by: takawata
MFC after: 1 week
same ASIC ID of BCM5758 such that r198318 incorecctly enabled TSO
on BCM5754.BCM5754M controllers. BCM5754/BCM5754M needs a special
firmware to enable TSO and bge(4) does not support firmware based
TSO.
Reported by: ed
Tested by: ed
If the NAA is type 2, the Node WWN is the Port WWN with the 12 bits
of port (48..60) cleared. This iff a wwn fetched from NVRAM is zero.
MFC after: 1 week
Unfortunately there are two slight problems with that:
- Yacc and lex might generate code that generates warnings because of
this. Require yacc and lex to be rebuilt during bootstrap. I'm not
incrementing __FreeBSD_version here, because I assume someone else
will do this eventually.
- When running `make buildkernel', it uses share/mk from the source
treeo to build aicasm. Because aicasm also depends on lex, this would
break. Lower WARNS to 5 for now. We should just increment it to 6
again somewhere in the very far future.
stored in a BAR since the CIS BAR is mapped before the PCI bus driver
enumerates all the BARs. Without this change, the PCI bus driver would
attempt to initialize a BAR that was already allocated resulting in a panic.
handling for the PCIR_BIOS decoding enable bit from the cardbus driver.
The PCIR_BIOS BAR does include type bits like other BARs. Instead, it is
always a 32-bit non-prefetchable memory BAR where the low bit is used as a
flag to enable decoding.
Reviewed by: imp
This replaces d_mmap() with the d_mmap2() implementation and also
changes the type of offset to vm_ooffset_t.
Purge d_mmap2().
All driver modules will need to be rebuilt since D_VERSION is also
bumped.
Reviewed by: jhb@
MFC after: Not in this lifetime...
get required command protocol. But they have no idea about new commands,
such as DATA SET MANAGEMENT (TRIM). As soon as this info any way provided
by CAM, give controller specific instructions.
* new firmware
* untested support for 1000 and 6000 series
* bgscan support
* remove unnecessary RXON changes
* allow setting of country/regdomain by enforcing channel flags read
from the EEPROM
* suspend/resume fixes
* RF kill switch fixes
* LED adjustments
* several bus_dma*() related fixes
* addressed some LORs
* many other bug fixes
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Obtained from: Brandon Gooch <jamesbrandongooch at gmail dot com> (LED
related changes), Benjamin Kaduk <kaduk at mit dot edu>
(LOR fixes), OpenBSD
Fix some wrong usages.
Note: this does not affect generated binaries as this argument is not used.
PR: 137213
Submitted by: Eygene Ryabinkin (initial version)
MFC after: 1 month
blkif interface in Xen requires all I/O to be 512 byte aligned with each
segment bounded by a 4k page.
Note: This submission only documents the proper contraints for blkif I/O.
The alignment code in busdma does not yet handle alignment constraints
correctly in all cases.
* Correct a group of typos: for Core2 programmable events, check
user supplied umask values against the correct event descriptor
field.
Submitted by: Ryan Stone <rysto32 at gmail dot com>
