and tw_so_options defined here which is supposed to be a copy of the
former (short vs u_short respectively).
Switch tw_so_options to be "signed short" to match the type of the field
it's inherited from.
Some g_raid tasters attempt metadata reads in multiples of the provider
sectorsize. Reads larger than MAXPHYS are invalid, so detect and abort
in such situations.
Spiritually similar to r217305 / PR 147851.
PR: 214721
Sponsored by: Dell EMC Isilon
m_pulldown()
m_pulldown() only needs to determine if a mbuf is writable if it is going to
copy data into the data region of an existing mbuf. It does this to create a
contiguous data region in a single mbuf from multiple mbufs in the chain. If
the requested memory region is already contiguous and nothing needs to
change, the mbuf does not need to be writeable.
Submitted by: Brian Mueller <bmueller@panasas.com>
Reviewed by: bz
MFC after: 1 week
Sponsored by: Panasas
Differential Revision: https://reviews.freebsd.org/D9053
The period should be taken into account by the function which
refreshes driver stats.
Reviewed by: philip
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D9130
Firmware version which takes PERIOD_MS parameter into account is
required.
Reviewed by: philip
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D9129
drain timeout handling to historical freebsd behavior.
The primary reason for these changes is the need to have tty_drain() call
ttydevsw_busy() at some reasonable sub-second rate, to poll hardware that
doesn't signal an interrupt when the transmit shift register becomes empty
(which includes virtually all USB serial hardware). Such hardware hangs
in a ttyout wait, because it never gets an opportunity to trigger a wakeup
from the sleep in tty_drain() by calling ttydisc_getc() again, after
handing the last of the buffered data to the hardware.
While researching the history of changes to tty_drain() I stumbled across
some email describing the historical BSD behavior of tcdrain() and close()
on serial ports, and the ability of comcontrol(1) to control timeout
behavior. Using that and some advice from Bruce Evans as a guide, I've
put together these changes to implement the hardware polling and restore
the historical timeout behaviors...
- tty_drain() now calls ttydevsw_busy() in a loop at 10 Hz to accomodate
hardware that requires polling for busy state.
- The "new historical" behavior for draining during close(2) is retained:
the drain timeout is "1 second without making any progress". When the
1-second timeout expires, if the count of bytes remaining in the tty
layer buffer is smaller than last time, the timeout is extended for
another second. Unfortunately, the same logic cannot be extended all
the way down to the hardware, because the interface to that layer is a
simple busy/not-busy indication.
- Due to the previous point, an application that needs a guarantee that
all data has been transmitted must use TIOCDRAIN/tcdrain(3) before
calling close(2).
- The historical behavior of honoring the drainwait setting for TIOCDRAIN
(used by tcdrain(3)) is restored.
- The historical kern.drainwait sysctl to control the global default
drainwait time is restored, but is now named kern.tty_drainwait.
- The historical default drainwait timeout of 300 seconds is restored.
- Handling of TIOCGDRAINWAIT and TIOCSDRAINWAIT ioctls is restored
(this also makes the comcontrol(1) drainwait verb work again).
- Manpages are updated to document these behaviors.
Reviewed by: bde (prior version)
This lets one interrupt DDB's output, which is useful if paging is
disabled and the output device is slow.
Submitted by: Anton Rang <rang@acm.org>
Reviewed by: jhb
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9138
Include netinet/in.h before ip_compat.t which will then check if
IPPROTO_IPIP is defined or not. Doing it the other way round,
ip_compat.h would not find it defined and netinet/in.h then
redefine it.
Active Open:
- Save the socket's vnet at the time of the active open (t4_connect) and
switch to it when processing the reply (do_act_open_rpl or
do_act_establish).
Passive Open:
- Save the listening socket's vnet in the driver's listen_ctx and switch
to it when processing incoming SYNs for the socket.
- Reject SYNs that arrive on an ifnet that's not in the same vnet as the
listening socket.
CLIP (Compressed Local IPv6) table:
- Add only those IPv6 addresses to the CLIP that are in a vnet
associated with one of the card's ifnets.
Misc:
- Set vnet from the toepcb when processing TCP state transitions.
- The kernel sets the vnet when calling the driver's output routine
so t4_push_frames runs in proper vnet context already. One exception
is when incoming credits trigger tx within the driver's ithread. Set
the vnet explicitly in do_fw4_ack for that case.
MFC after: 3 days
Sponsored by: Chelsio Communications
With clang 4.0.0, we are getting the following warnings about struct
boot_module_t in efi's boot_module.h:
In file included from sys/boot/efi/boot1/ufs_module.c:41:
sys/boot/efi/boot1/boot_module.h:67:14: error: this function declaration is not a prototype [-Werror,-Wstrict-prototypes]
void (*init)();
^
void
sys/boot/efi/boot1/boot_module.h:92:16: error: this function declaration is not a prototype [-Werror,-Wstrict-prototypes]
void (*status)();
^
void
sys/boot/efi/boot1/boot_module.h:95:24: error: this function declaration is not a prototype [-Werror,-Wstrict-prototypes]
dev_info_t *(*devices)();
^
void
3 errors generated.
Fix this by adding 'void' to the parameter lists. No functional change.
Reviewed by: emaste, imp, smh
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D9144
With clang 4.0.0, the EFI API header causes the following warning:
In file included from sys/boot/efi/loader/bootinfo.c:43:
In file included from sys/boot/efi/loader/../include/efi.h:52:
sys/boot/efi/include/efiapi.h:534:32: error: this function declaration is not a prototype [-Werror,-Wstrict-prototypes]
(EFIAPI *EFI_RESERVED_SERVICE) (
^
Add VOID to make it into a real prototype.
Reviewed by: imp, emaste, tsoome
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D9132
after it, which has a conflicting definition of errno. This leads to
the following warning with clang 4.0.0:
In file included from sys/boot/common/reloc_elf32.c:6:
In file included from sys/boot/common/reloc_elf.c:37:
/usr/obj/usr/src/tmp/usr/include/stand.h:155:12: error: this function declaration is not a prototype [-Werror,-Wstrict-prototypes]
extern int errno;
^
sys/sys/errno.h:46:26: note: expanded from macro 'errno'
#define errno (* __error())
^
MFC after: 3 days
We would previously invalidate such entries individually, resulting in more
IPIs than necessary.
Reviewed by: alc, kib
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D9094
biowait() will otherwise race with completions of such BIOs. In-tree code
only calls biowait() on BIOs that do not specify a handler, so this change
should not have any functional impact.
Reviewed by: mav
MFC after: 1 month
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D9070
This was meant to be used by a future FORTIFY_SOURCE implementation.
Probably for good, FORTIFY_SOURCE and this particular GCCism were never
well supported by clang or other compilers. Furthermore, the technology
has long since been replaced by either static checkers, sanitizers, or
even just the strong stack protector that was enabled by default.
Drop __gnu_inline to avoid cluttering the headers.
MFC after: 5 days
clang 3.9.0 without -fPIC generates absolute jump table for
switch/case statement which trips boot1.efi and loader.efi
on ARM platform.
Reviewed by: andrew
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D9108
Fix section pattern code to exclude .rel.data.* sections from being
merged into .data. Otherwise relocations in those sections are lost
in final binary
Reviewed by: andrew
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D9108
__bss_end should not be included in .bss zeroing code. Otherwise first 4
bytes of the section that follows .bss (in loader's case it's .sdata) are
overwritten by zero.
Reviewed by: andrew
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D9108
In-tree objdump is too old to dump new ELF headers. But for example if we
use: `make CROSS_TOOLCHAIN=riscv64-gcc TARGET_ARCH=riscv64` and do not specify
CROSS_BINUTILS_PREFIX in env, embed_mfs.sh cannot find the correct objdump.
This patch just replaces using of objdump with elfdump to collect needed
information.
Later we may also put an ELFDUMP in CROSSENV and use it in embed_mfs.sh .
Reviewed by: emaste, br
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D9062
a linuxkpi style device is expected. If OFED/linuxkpi actually starts
using this field then we'll have to figure out whether to create fake
devices for these drivers or have linuxkpi deal with NULL device.
This mismatch was first reported as part of D6585.
Unnecessary prefetch just loads HW prefetcher and displaces other
cache entries (which could be really useful).
If we parse mbuf for TSO early and use firmware-assisted TSO, we do not
expect mbuf data access when we compose firmware-assisted TSO (v1 or v2)
option descriptors. If packet header needs to be linearized or finally
FATSO cannot be used because of, for example, too big header, we do not
care about a bit more performance degradation because of prefetch
absence (it is better to optimize more common case).
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D9120
in some arm64 hardware, for example the AMD Opteron A1100.
Reviewed by: mav
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8852
This is needed for two reasons:
* Drivers will need to know what the negotiated set of VHT capabilities
and rates are in order to configure (and reconfigure for opmode/chanwidth
changes) how to speak to a given peer; and
* Because some vendors are "special", we should be careful in what we announce
to them during peer association.
This isn't the complete solution, as I still need to make sure that when
sending out probe requests before we know what we want, we don't limit
the capabilities being announced. This is important for IBSS/mesh work
later on as probe request/response exchanges are the first hint at what
a peer supports. I'll look at adding that to the API soon.
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
These have been tested back-to-back with Linux 3.x and a similar attachment
at the other end; a CDC EEM-like encapsulation can be used for emulated
Ethernet over udbp(4) with ng_ether.
potentially leading to fatal unaligned accesses on architectures with
strict alignment requirements. This change fixes dummynet(4) as far
as accesses to 64-bit members of struct dn_* are concerned, tripping
up on sparc64 with accesses to 32-bit members happening to be correctly
aligned there. In other words, this only fixes the tip of the iceberg;
larger parts of dummynet(4) still need to be rewritten in order to
properly work on all of !x86.
In principle, considering the amount of code in dummynet(4) that needs
this erroneous pattern corrected, an acceptable workaround would be to
declare all struct dn_* packed, forcing compilers to do byte-accesses
as a side-effect. However, given that the structs in question aren't
laid out well either, this would break ABI/KBI.
While at it, replace all existing bcopy(9) calls with memcpy(9) for
performance reasons, as there is no need to check for overlap in these
cases.
PR: 189219
MFC after: 5 days
If some process' nodes were accessed using procfs and the process
cannot exit properly at the time modunload event is reported to the
pseudofs-backed filesystem, the assertion in pfs_vncache_unload() is
triggered. Assertion is correct, the cache should be cleaned.
Approved by: des (pseudofs maintainer)
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Instead of collecting statistics for each combination of ports and logical
units, that consumed ~45KB per LU with present number of ports, collect
separate statistics for every port and every logical unit separately, that
consume only 176 bytes per each single LU/port. This reduces struct
ctl_lun size down to just 6KB.
Also new IOCTL API/ABI does not hardcode number of LUs/ports, and should
allow handling of very large quantities.
MFC after: 2 weeks (probably keeping old API enabled for some time)
handler which already holds the mutex, and have sdhci_handle_card_present()
be just a tiny wrapper that does the locking for external callers.
This should fix the recursive locking panics seen on rpi3.
Reported by: Shawn Webb
Besides slots always having non-removable media, these HCIs require
a custom hardware reset sequence after power-up.
- Flesh out the support for Intel Braswell eMMC controllers further.
Apart from also requiring said reset code, the timeout clock needs to
be hardcoded to 1 MHz for these.
Both the special reset and timeout clock handlings are implemented as
global sdhci(4) quirks as the same treatment will be necessary for
Intel eMMC controllers attached via ACPI (once sdhci(4) grows such a
front-end).
- In sdhci_init_slot(), use the right capability field for determining
the announced bus width based on MMC_CAP_*_BIT_DATA.
- Correct inverted sdhci_pci_softc member comments added in r276469. [1]
Submitted by: Anton Yuzhaninov [1]
MFC after: 5 days
or write, resulting in random short-read and short-write returns for
requests. Fixing this fixes nominal block I/O via mmcsd(4).
Obtained from: DragonFlyBSD (fd4b97583be1a1e57234713c25f6e81bc0411cb0)
MFC after: 5 days
This array takes 64KB of RAM now, that was more then half of struct ctl_lun
size. If at some point we support more ports, this may need another tune.
MFC after: 2 weeks
card presence and write protect switch detection.
A bridge driver just needs to call the setup routine in its attach(), the
teardown in its detach(), and write a couple tiny glue functions to connect
the sdhci interface functions to the new helper functions. This is not
extensively documented, but multiple examples will exist real soon.
card insert/remove events on controllers that don't implement the insert
and remove interrupts.
Bridge drivers can set a new slot option, SDHCI_NON_REMOVABLE, to indicate
non-removable media (such as eMMC). The sdhci driver will not enable
insert/remove interrupts, and sdhci_generic_get_card_present() will always
return true.
Bridge drivers can set a new quirk, SDHCI_QUIRK_POLL_CARD_PRESENT, and the
sdhci driver will not enable insert/remove interrupts, and instead will use
a callout to poll the card-present status at 5 Hz.
For bridge drivers that get notified of card insert/remove via gpio
interrupts, there is a new sdhci_handle_card_present() function they can
call from the gpio interrupt handler to inform the sdhci code of the event.
In addition to adding these new features, the existing code to debounce card
insertions was updated to use taskqueue_enqueue_timeout() instead of
scheduling a callout to do the taskqueue_enqueue(). There is also now a
comment explaining that insertion-debounce is what's going on -- it took me
a long time to realize that's what the old sdhci_card_delay() routine was
really doing. There is no functional difference between the old and new
debounce code (I hope!).
Use device-specific Rx buffer size to ensure that data will not be
truncated + add a warning if truncation was detected (the driver
cannot handle this case correctly yet).
Tested with:
- RTL8188CUS, RTL8188EU and RTL8821AU, STA / AP modes.
There are places where checks are made against VM_MAX_KERNEL_ADDRESS, or
virtual_end (set to VM_MAX_KERNEL_ADDRESS). With 32-bit checks, an address will
always be less than or equal to 0xffffffff. Drop a page, so those checks can
terminate loops safely.
With clang 4.0.0, I'm getting the following warnings:
sys/geom/vinum/geom_vinum_state.c:186:7: error: logical not is only
applied to the left hand side of this bitwise operator
[-Werror,-Wlogical-not-parentheses]
if (!flags & GV_SETSTATE_FORCE)
^ ~
The logical not operator should obiously be called after masking.
Reviewed by: mav, pfg
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D9093
This function is used only by ipsec_getpolicybysock() to fill security
policy index selector for locally generated packets (that have INPCB).
The function incorrectly assumes that spidx is the same for both directions.
Fix this by using new direction argument to specify correct INPCB security
policy - sp_in or sp_out. There is no need to fill both policy indeces,
because they are overwritten for each packet.
This fixes security policy matching for outbound packets when user has
specified TCP/UDP ports in the security policy upperspec.
PR: 213869
MFC after: 1 week
Inums in cd9660 refer to byte offsets on the media. DVD and BD media
can have entries above 4GB, especially with multi-session images.
PR: 190655
Reported by: Thomas Schmitt <scdbackup at gmx.net>
And HP x2 210, per DragonFlyBSD 240bd9cd58f8259c12c14a8006837e698.
Submitted by: Johannes Lundberg <yohanesu75 at gmail.com>
No objection: gonzo@
Obtained from: DragonFlyBSD
This is a skeleton set based on ieee80211_ht.c. It implements some IE
parsing, some basic unfinished negotiation, and channel promotion/demotion.
However, by itself it's not enough to do VHT - notably, the actual
channel promotion for STA mode at least is done in ieee80211_ht.c as
part of htinfo_update_chw(). I was .. quite amused when I found that
out.
I'm checking this in so others can see progress rather than one huge
commit when VHT is "done" (which will likely be quite a while.)
Many embedded SoC controllers that are (more or less) sdhci-compatible don't
implement card detect, and the related values in the PRESENT_STATE register
aren't useful. A bridge driver can now implement get_card_present() to read
a gpio pin or whatever else is necessary for that system.
The default implementation reads the CARD_PRESENT bit from the PRESENT_STATE
register, so existing drivers will keep working (or keep not-fully-working,
since many drivers right now can't detect card insert/remove).
sched_*(2) syscalls might be not available at runtime. Defining this
constant as zero directs POSIX-compliant code to call sysconf(3) to
detect the feature at runtime, and forces libc sysconf(3) to ask
kernel.
Noted by: ngie
Reviewed by: jilles, ngie
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D9055
Siena has limitation on maximum byte count and 4k boundary crosssing
(which is stricter than maximum byte count).
EF10 has limitation on maximum byte count only.
Reviewed by: philip
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D9061
It is safer to consider EFX_LINK_UNKNOWN as link down.
link_mode is set to EFX_LINK_UNKNOWN on port stop and fini.
Reviewed by: philip
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D9060
* Add the VHT capability element to the driver capabilities so ifconfig
can see if VHT is available
* Add ioctl plumbing for enabling/disabling VHT and each of the VHT
widths.
Note: this DOES change the ABI (the driver caps ioctl struct size, sigh)
so this will require a recompile of at least ifconfig.
In preparation for VHT station support, we need to store VHT IEs when
scanning so we can choose to upgrade to VHT.
This doesn't change the ABI - it just steals spare[] entries.
The VHT operational element (VHTOPMODE) isn't a uint32_t - it's
the MCS sets, freq1/freq2 parameters and channel width.
So, store the channel width too in lieu of just storing the
IE struct.
This changes the VHT parameter layout in ieee80211_node but it
doesn't change ABI at all.
The 11n code uses these bits for both configuration /and/ controlling
the channel width on softmac chips - it uses it to find the widest
width for all VAPs (eg a HT20 vap and a HT40 vap) to know what to
configure the ic_curchan.
For fullmac devices it isn't /as/ important, as each virtual device
exposed by the firmware will likely have its own configuration and the
firmware figures out what to do to enable it.
These came from Linux mac80211 headers and are configuration bits, not
VHTOPMODE field parameters.
Whilst here, add the field names for the VHTCAP bits.
Tested:
* ath10k, 11ac STA mode
Add a MSG_MOREOTOCOME message flag. When this flag is set, sosend*
set PRUS_MOREOTOCOME when invoking the protocol send method. The aio
worker tasks for sending on a socket set this flag when there are
additional write jobs waiting on the socket buffer.
Reviewed by: adrian
MFC after: 1 month
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D8955
Build and install an o32 set of libraries on mips64 suitable for
running o32 binaries via COMPAT_FREEBSD32. Enable COMPAT_FREEBSD32 in
MALTA64.
Reviewed by: jmallett, imp
Sponsored by: DARPA / AFRL
Differential Revision: https://reviews.freebsd.org/D9032
If tmpfs vnode is only shared locked, tn_status field still needs
updates to note the access time modification. Use the same locking
scheme as for UFS, protect tn_status with the node interlock + shared
vnode lock.
Fix nearby style.
Noted and reviewed by: mjg
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
sys/ptrace.h includes sys/signal.h, which includes sys/_sigset.h.
Note that sys/_sigset.h only defines osigset_t if COMPAT_43 was defined.
Two lines later, sys/ptrace.h includes machine/reg.h, which in case of
powerpc, includes opt_compat.h.
After the include headers reordering in r311345, we have sys/ptrace.h
included before sys/sysproto.h.
If COMPAT_43 was requested in the kernel config, the result is that
sys/_sigset.h does not define osigset_t, but sys/sysproto.h sees
COMPAT_43 and uses osigset_t.
Fix this by explicitely including opt_compat.h to cover the whole
kern/kern_exec.c scope.
Sponsored by: The FreeBSD Foundation
This ensures the interface is initialized by the interface driver
before it can be used by the rest of the system.
Reviewed by: jhb, karels, gnn
MFC after: 3 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8905
The format strings weren't checked when stacksave_subr() used a function
pointer for printf instead of directly using db_printf().
Reported by: kib
Sponsored by: DARPA / AFRL
Do not hardcode elf64-tradbigmips as output format in BERI linker scrips.
Unfortunately, in-tree toolchain and external newer versions of binutils
mean two different things under that. When creating elf binaries using
external toolchain, gcc uses elf64-tradbigmips-freebsd and so linker
script file has to match in order for ld to be able to create the final loader
binary.
Rather than trying to guess, remove hardcoded output format directive from
the linker directive files and use CC to invoke the linker instead.
Reviewed by: brooks
Differential Revision: https://reviews.freebsd.org/D9050
Armada38x is already supported in the tree.
This commit adds support for DB-AP board.
File was taken from Linux v4.8 and accustomed to FreeBSD
in minimal possible way.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D7327
ClearFog is equipped with Marvell Armada 388 SoC, which is already
supported in FreeBSD.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D7326
Right now size of the structure is 472 bytes on amd64, which is
already large and stack allocations are indesirable. With the ino64
work, MNAMELEN is increased to 1024, which will make it impossible to have
struct statfs on the stack.
Extracted from: ino64 work by gleb
Discussed with: mckusick
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Hardware buffer management entries are not used yet by FreeBSD.
They were added for compliance with Linux Armada 38x device tree
representation and will be used in future network support.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D8179
- recognize ports and vlangroups based on DTS file
- support multi-chip addresing mode (required in upcoming
Armada-388-Clearfog support)
- refactor attachment function
Each port in 'dsa' node should have 'vlangroup' property. Otherwise,
e6000sw will fail to attach.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D7328
* rename the ieee80211com field for vht mcsinfo to be ic_, not iv;
* add a vht config field, stealing from the spares I left there.
This doesn't change the ABI.
The HT40 channel population logic was "just" doing pairs of channels starting with
the band entry frequency. Trouble is, a lot of the rules start way off at 5120MHz,
which isn't a valid 5GHz channel. Then, eg for HT40U, it would populate:
* (5120,5140)
* (5160,5180)
* (5200,5220)
* (5240,5260)
.. as the HT40U pairs, with the first being the primary channel. Channel 36
is 5180MHz, and since it's not a primary channel here, it wouldn't populate it.
Then, the next HT40U would be 5200/5220, which is highly wrong.
HT40D had the same problem.
So, this just forces that 5GHz HT40 channels start at channel 36 (5180),
no matter what the band edge says. This includes eg doing 4.9GHz channels.
This erm, meant that the HT40 channels for the low band was always wrong.
Oops!
Tested:
* AR9380, STA mode
* AR9344 SoC, AP mode
MFC after: 1 week
