ddfc9c4c59 was missing changes to two files to complete the
bus_child_pnpinfo_str->bus_child_pnpinfo. This fixes the broken kernel
builds.
Sponsored by: Netflix
Now that the upper layers all go through a layer to tie into these
information functions that translates an sbuf into char * and len. The
current interface suffers issues of what to do in cases of truncation,
etc. Instead, migrate all these functions to using struct sbuf and these
issues go away. The caller is also in charge of any memory allocation
and/or expansion that's needed during this process.
Create a bus_generic_child_{pnpinfo,location} and make it default. It
just returns success. This is for those busses that have no information
for these items. Migrate the now-empty routines to using this as
appropriate.
Document these new interfaces with man pages, and oversight from before.
Reviewed by: jhb, bcr
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D29937
If the connection is in the process of disconnecting, ic_socket can be
NULL. For icl_cxgbei_conn_transfer_setup(), lock the connection and
check ic_socket before using it. For icl_cxgbei_conn_task_setup(),
the caller already holds the connection lock, so assert it and bail
early with ECONNRESET if the connection is disconnecting.
Reported by: Jithesh Arakkan @ Chelsio
Fixes: f949967c8e cxgbei: Fix a race between transfer setup and a peer reset.
The INQUIRY command may return a CAM_DATA_RUN_ERR code, even when
it succeeds. This happens during driver startup, causing the
current and further inquiries to be aborted, resulting in some
missing information about the controller.
Reviewed by: imp
Sponsored by: Instituto de Pesquisas Eldorado (eldorado.org.br)
Differential Revision: https://reviews.freebsd.org/D30843
Reserve one page for the DMA subsystem, that may need it when the I/O
buffer is not page aligned.
Without this change, writes with the maximum allowed size failed, if:
- physical memory was fragmented, making it necessary to use one DMA
segment for each page
- the buffer to be written was not page aligned, causing the DMA
subsystem to need one extra segment
In the scenario above, the DMA subsystem would run out of segments,
resulting in a write with no SG segments, that would fail.
Reviewed by: imp
MFC after: 2 weeks
Sponsored by: Instituto de Pesquisas Eldorado (eldorado.org.br)
Differential Revision: https://reviews.freebsd.org/D30798
ni_txseqs is kept as 16-bit counter, but we need to trim the upper four
bits as they may have special meanings for the firmware / hardware.
For instance, bit 15 enables hardware / firmware generation of sequence
numbers that overrides sequence numbers programmed by the driver.
Reviewed by: adrian
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D30814
Given all the code does operate on struct ifnet, the last step in this
longer series of changes now is to rename struct net_device to
struct ifnet (that is what it was defined to in the LinuxKPi code).
While mlx4 and OFED are "shared" code the decision was made years ago
to not write it based on the netdevice KPI but the native ifnet KPI
for most of it. This commit simply spells this out and with that
frees "struct netdevice" to be re-done on LinuxKPI to become a more
native/mixed implementation over time as needed by, e.g., wireless
drivers.
Sponsored by: The FreeBSD Foundation
MFC after: 10 days
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D30515
The NIC TLS and TOE TLS modes in cxgbe(4) both work with TLS key
contexts. Previously, TOE TLS supported TLS key contexts created by
two different methods, and NIC TLS had a separate bit of code copied
from NIC TLS but specific to KTLS. Now that TOE TLS only supports
KTLS, pull common code for creating TLS key contexts and programming
them into on-card memory into t4_keyctx.c.
Sponsored by: Chelsio Communications
TOE TLS offload was first supported via a customized OpenSSL developed
by Chelsio with proprietary socket options prior to KTLS being present
either in FreeBSD or upstream OpenSSL. With the addition of KTLS in
both places, cxgbe's TOE driver was extended to support TLS offload
via KTLS as well. This change removes the older interface leaving
only the KTLS bindings for TOE TLS.
Since KTLS was added to TOE TLS second, it was somehat shoe-horned
into the existing code. In addition to removing the non-KTLS TLS
offload, refactor and simplify the code to assume KTLS, e.g. not
copying keys into a helper structure that mimic'ed the non-KTLS mode,
but using the KTLS session object directly when constructing key
contexts.
This also removes some unused code to send TX keys inline in work
requests for TOE TLS. This code was never enabled, and was arguably
sending the wrong thing (it was not sending the raw key context as we
do for NIC TLS when using inline keys).
Sponsored by: Chelsio Communications
Some code was using it already, but in many places we were testing
SO_ACCEPTCONN directly. As a small step towards fixing some bugs
involving synchronization with listen(2), make the kernel consistently
use SOLISTENING(). No functional change intended.
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Last an(4) devices have been End Of Life and End Of Sale in 2007.
Time to remove this driver.
Differential Revision: https://reviews.freebsd.org/D30679
Reviewed by: imp (earlier version), emaste (earlier version)
Sponsored by: Diablotin Systems
Last an(4) devices have been End Of Life and End Of Sale in 2007.
Time to remove this driver.
Differential Revision: https://reviews.freebsd.org/D30678
Reviewed by: imp (earlier version), adrian (earlier version)
MFC after: 3 days
Sponsored by: Diablotin Systems
This framework is initial implementation of the simple-audio-card compatible
audio driver framework. It provides glue for CPU/codec/aux device.
Differential Revision: https://reviews.freebsd.org/D27830
Some arm64 SoCs have nodes in their fdts that describe devices
connected to the internal PCI bus. One such SoC is Freescale LS1028A.
In order to access information stored in them we need to add ofw bus
support to pci. Pass devinfo request up to our parent, which
is responsible for parsing all the information.
It allows to use ofw interface on PCI devices that support it.
This method is similar to sys/dev/acpica/acpi_pci.c.
Submitted by: Kornel Duleba <mindal@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Alstom Group
Differential Revision: https://reviews.freebsd.org/D30181
Some arm64 SoCs have nodes in their fdts that describe devices
connected to the internal PCI bus. One such SoC is Freescale LS1028A.
It expects the nodes to be mapped to devices enumerated using the standard
PCI method. Mapping is done by reading device and function ids from "reg"
property. Information is dts is used to describe MDIO/PHY connected
to a given interface.
Submitted by: Kornel Duleba <mindal@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Alstom Group
Differential Revision: https://reviews.freebsd.org/D30180
ThunderX is the only board known to use them.
Move them to the ThunderX PCIe driver.
Submitted by: Kornel Duleba <mindal@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Alstom Group
Differential Revision: https://reviews.freebsd.org/D30179
The vmbus ISR needs to live in a trampoline. Dynamically allocating a
trampoline at driver initialization time poses some difficulties due to
the fact that the KENTER macro assumes that the offset relative to
tramp_idleptd is fixed at static link time. Another problem is that
native_lapic_ipi_alloc() uses setidt(), which assumes a fixed trampoline
offset.
Rather than fight this, move the Hyper-V ISR to i386/exception.s. Add a
new HYPERV kernel option to make this optional, and configure it by
default on i386. This is sufficient to make use of vmbus(4) after the
4/4 split. Note that vmbus cannot be loaded dynamically and both the
HYPERV option and device must be configured together. I think this is
not too onerous a requirement, since vmbus(4) was previously
non-functional.
Reported by: Harry Schmalzbauer <freebsd@omnilan.de>
Tested by: Harry Schmalzbauer <freebsd@omnilan.de>
Reviewed by: whu, kib
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D30577
During boot we warn that the kbd and openfirm drivers are Giant-locked
and may be deleted. Generally, the warning helps signal that certain
old drivers are not being maintained and are subject to removal, but
this doesn't really apply to certain drivers which are harder to
detangle from Giant.
Add a flag, D_GIANTOK, that devices can specify to suppress the
misleading warning. Use it in the kbd and openfirm drivers.
Reviewed by: imp, jhb
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D30649
Normally raw interrupt handler is provided by the kernel text. But
vmbus module registers its own handler that needs to be mapped into
userspace mapping on PTI kernels.
Reported and reviewed by: whu
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D30310
pqisrc_is_firmware_feature_enabled shouldn't be declared inline in a
header, and then static inline in the .c function. Remove this stray
declartion from the header. gcc6 complains, but clang does not.
Sponsored by: Netflix
When a DMA chain can't be loaded, set the state to STATE_INQUEUE so that
the mp[rs]_complete_command can properly fail the command.
Sponsored by: Netflix
When the mpr(4) and mps(4) drivers probe a SATA device, they issue an
ATA Identify command (via mp{s,r}sas_get_sata_identify()) before the
target is fully setup in the driver. The drivers wait for completion of
the identify command, and have a 5 second timeout. If the timeout
fires, the command is marked with the SATA_ID_TIMEOUT flag so it can be
freed later.
That is where the use-after-free problem comes in. Once the ATA
Identify times out, the driver sends a target reset, and then frees any
identify commands that have timed out. But, once the target reset
completes, commands that were queued to the drive are returned to the
driver by the controller.
At that point, the driver (in mp{s,r}_intr_locked()) looks up the
command descriptor for that particular SMID, marks it CM_STATE_BUSY and
sends it on for completion handling.
The problem at this stage is that the command has already been freed,
and put on the free queue, so its state is CM_STATE_FREE. If INVARIANTS
are turned on, we get a panic as soon as this command is allocated,
because its state is no longer CM_STATE_FREE, but rather CM_STATE_BUSY.
So, the solution is to not free ATA Identify commands that get stuck
until they actually return from the controller. Hopefully this works
correctly on older firmware versions. If not, it could result in
commands hanging around indefinitely. But, the alternative is a
use-after-free panic or assertion (in the INVARIANTS case).
This also tightens up the state transitions between CM_STATE_FREE,
CM_STATE_BUSY and CM_STATE_INQUEUE, so that the state transitions happen
once, and we have assertions to make sure that commands are in the
correct state before transitioning to the next state. Also, for each
state assertion, we print out the current state of the command if it is
incorrect.
mp{s,r}.c: Add a new sysctl variable, dump_reqs_alltypes,
that controls the behavior of the dump_reqs sysctl.
If dump_reqs_alltypes is non-zero, it will dump
all commands, not just the commands that are in the
CM_STATE_INQUEUE state. (You can see the commands
that are in the queue by using mp{s,r}util debug
dumpreqs.)
Make sure that the INQUEUE -> BUSY state transition
happens in one place, the mp{s,r}_complete_command
routine.
mp{s,r}_sas.c: Make sure we print the current command type in
command state assertions.
mp{s,r}_sas_lsi.c:
Add a new completion handler,
mp{s,r}sas_ata_id_complete. This completion
handler will free data allocated for an ATA
Identify command and free the command structure.
In mp{s,r}_ata_id_timeout, do not set the command
state to CM_STATE_BUSY. The command is still in
queue in the controller. Since we were blocking
waiting for this command to complete, there was
no completion handler previously. Set the
completion handler, so that whenever the command
does come back, it will get freed properly.
Do not free ATA Identify commands that have timed
out in mp{s,r}sas_add_device(). Wait for them
to actually come back from the controller.
mp{s,r}var.h: Add a dump_reqs_alltypes variable for the new
dump_reqs_alltypes sysctl.
Make sure we print the current state for state
transition asserts.
This was tested in the Spectra Logic test bed (as described in the
review), as well Netflix's Open Connect fleet (where panics dropped from
a dozen or two a month to zero).
Reviewed by: imp@ (who is handling the commit with ken's OK)
Sponsored by: Spectra Logic
Differential Revision: https://reviews.freebsd.org/D25476
Use the accessor function to get the softc for this sim. This also drops
an unneeded cast.
Sponsored by: Netflix
Reviewed by: mav@, hselasky@
Differential Revision: https://reviews.freebsd.org/D30360
if (sb == NULL) { ... sb->s_error } is going to be a bad time. Return
ENOMEM when we cannot allocate an sbuf for the sysctl rather than
dereferencing the NULL pointer just returned.
Reviewed by: manu@, allanjude@
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D30373
The need for !! over (bool) pre-dates gcc 4.2, so go with the patch
as-submitted because the kernel tends to prefer that.
Suggested by: emaste@
Sponsored by: Netflix
Currently, mmc_fdt_gpio_get_{present,readonly} return all time true.
true ^ 100b = true
false ^ 100b = true
since that's done after promotion to integers. Use !! to convert
the bit to a bool before xor.
Reviewed by: imp@ (converted to (bool) to !! for portability)
Pull Request: https://github.com/freebsd/freebsd-src/pull/461
Update mmc_switch_status to ignore a few CRC errrors when asking for the
card status after setting the new rate with CMD6. Since the card may
take a little while to make the switch, it's possible we'll get a
communications error if we sent the command at the wrong time. Several
low end laptops needs this workaround as they have a window that seems
longer than other systems. This is known to fix at least the Acer Aspire
A114-32-P7E5.
Reviewed by: imp@, manu@
Differential Revision: https://reviews.freebsd.org/D24740
This patch adds the necessary methods resolution to the sdhci_xenon
driver which are required to configure UHS modes for SD/MMC devices.
Apart from the two generic routines, the custom sdhci_xenon_set_uhs_timing
function is responsible for setting the SDHCI_HOST_CONTROL2 register
with appropriate mode select values - in case of HS200 and HS400
they are non-standard.
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Marvell
Differential Revision: https://reviews.freebsd.org/D30565
MFC after: 2 weeks
Improve the VCCQ voltage switch, so that to properly
handle the SDHCI_HOST_CONTROL2 register signaling
flags and along with manipulating the regulator.
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Marvell
Differential Revision: https://reviews.freebsd.org/D30564
MFC after: 2 weeks
Until now the "no-1-8-v" DT flag wrongly disabled the SDHCI_CAN_VDD_180
- slot 1.8V power supply capability, whereas it refers to the signaling
voltage. Fix the sdhci_xenon_read_4 and allow to disable the UHS modes
depending on the DT property or PHY slow mode. While at it - make sure
the unsupported 1.2V signaling is always disabled and not reported
in the bootverbose log.
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Marvell
Differential Revision: https://reviews.freebsd.org/D30563
MFC after: 2 weeks
The mmc_fdt_parse allows to parse more MMC-related
FDT properties. Start using it. "wp-inverted" property,
VQMMC and newly added VMMC power supply parsing
is now done in a generic code.
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Marvell
Differential Revision: https://reviews.freebsd.org/D30562
MFC after: 2 weeks
With this change the host controller drivers can set the MMC capabilities
(e.g. using mmc_fdt_parse() helper) before calling sdhci_init_slot().
This way the configuration dump (eg. in bootverbose) can include the
possible additional information.
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Marvell
Differential Revision: https://reviews.freebsd.org/D30561
MFC after: 2 weeks
This patch adds support for the SDHCI_CAN_DO_64BIT
capability, so that to allow 64-bit DMA operation
for the controllers which support this feature.
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Marvell
Differential Revision: https://reviews.freebsd.org/D30560
MFC after: 2 weeks
DBG2 ACPI table description [1] specifies three subtypes
related to 16550 UART:
0x0 - 16550 compatible
0x1 - 16550 subset
0x12 - 16550 compatible with parameters defined in Generic Address Structure (GAS)
It turned out however, that the Windows OS treats 0x0 subtype as
legacy x86 UART with 8-bit access. ARM SoCs can use types 0x1 (16550 with
fixed mmio32 access) or 0x12 (16550 with fully respected GAS contents).
Switch Marvell SoCs ACPI UART subtype to 0x1 - thanks to that the same firmware
can run properly with UART output in FreeBSD, Windows 10, Linux and ESXI
hypervisor. Tests showed the older firmware versions that use 0x0
UART subtype in SPCR table continue to display output properly.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/bringup/acpi-debug-port-table
Obtained from: Semihalf
Sponsored by: ARM
Differential revision: https://reviews.freebsd.org/D30386
MFC after: 2 weeks
Use the correct SGL limit within iw_cxgbe, firmwares >= 1.25.6.0 support
upto 512 entries per MR.
Obtained from: Chelsio Communications
MFC after: 1 week
Sponsored by: Chelsio Communications
Commit message of the identical change in Linux driver says:
"When an I2C HID device is powered off during system sleep, as a result
of removing its power resources (by the ACPI core) the interrupt line
might go low as well. This results inadvertent interrupts."
This change fixes suspend/resume on Asus S510UQ laptops.
While here add a couple of typo fixes as well as a slight change to the
iichid_attach() code to have the power_on flag set properly.
Submitted by: J.R. Oldroyd <jr_AT_opal_DOT_com>
Reviewed by: wulf
MFC after: 1 week
Changes since 1.25.0.0 are listed here. This list comes from the
Release Notes for the "Chelsio Unified Wire v3.14.0.3 for Linux"
release dated 2021-05-21.
Fixes
-----
BASE:
- Fixed Back to back T6 100G-CR4 link coming up with NO FEC sometimes.
- [T5] Try to bring up link in 1G speed if link doesn't come up on 10G.
- Fixed a bug to not allow BaseR fec in 100G speed.
- Fixed linkup issues on BT adapter in 1G and 100M speed.
- Fixed an issue to allow driver to send VI_ENABLE multiple times (once
with rx disable and then later rx enable).
- Fixed rate limiting not working on class number 16 to 30.
- Fixed backward compatibility issue in port type interpretation with vpd
version 0x80.
ETH:
- Fixed a case when firmware failed to deliver NIC WR completion to host.
- No rate limit support for WR ETH_TX_PKTS2 due to performance reasons.
OFLD
- Fixed a connection hang in SO adapters when tp_plen_max (set by driver)
is more than the window size.
- Added fw_filter_vnic_mode to firmware API file (t4fw_interface.h)
- Use correct rx channel in coprocessor crypto completion (CPL_FW6_PLD). This
was causing out of order completion to host.
FOiSCSI
- Fixed a crash due to unaligned access of ipv6 address.
- Fixed a crash during lun reset.
Enhancements
------------
ETH:
- Rate limiting support added for encapsulated (vxlan, nvgre, geneve) NIC TCP
packets.
OFLD:
- More than 128 SGLs supported in FW_RI_FR_NSMR_WR. Now, more than 16GB
(upto 64GB) of PBLs can be written with single FW_RI_FR_NSMR_WR.
Obtained from: Chelsio Communications
MFC after: 1 month
Sponsored by: Chelsio Communications
Part of the nvme recovery process for errors is to reset the
card. Sometimes, this results in failing the entire controller. When nda
is in use, we free the sim, which will sleep until all the I/O has
completed. However, with only one thread, the request fail task never
runs once the reset thread sleeps here. Create two threads to allow I/O
to fail until it's all processed and the reset task can proceed.
This is a temporary kludge until I can work out questions that arose
during the review, not least is what was the race that queueing to a
failure task solved. The original commit is vague and other error paths
in the same context do a direct failure. I'll investigate that more
completely before committing changing that to a direct failure. mav@
raised this issue during the review, but didn't otherwise object.
Multiple threads, though, solve the problem in the mean time until other
such means can be perfected.
Reviewed by: jhb@
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D30366
