Make the name cache hash as well as the nfsnode hash use it.
As a special tweak, create an unsigned version of register_t. This allows
us to use a special tweak for the 64 bit versions that significantly
speeds up the i386 version (ie: int64 XOR int64 is slower than int64
XOR int32).
The code layout is a little strange for the string function, but I was
able to get between 5 to 10% improvement over the original version I
started with. The layout affects gcc code generation choices and this way
was fastest on x86 and alpha.
Note that 'CPUTYPE=p3' etc makes a fair difference to this. It is
around 45% faster with -march=pentiumpro on a p6 cpu.
if we hold a spin mutex, since we can trivially get into deadlocks if we
start switching out of processes that hold spinlocks. Checking to see if
interrupts were disabled was a sort of cheap way of doing this since most
of the time interrupts were only disabled when holding a spin lock. At
least on the i386. To fix this properly, use a per-process counter
p_spinlocks that counts the number of spin locks currently held, and
instead of checking to see if interrupts are disabled in the witness code,
check to see if we hold any spin locks. Since child processes always
start up with the sched lock magically held in fork_exit(), we initialize
p_spinlocks to 1 for child processes. Note that proc0 doesn't go through
fork_exit(), so it starts with no spin locks held.
Consulting from: cp
- Don't try to grab Giant before postsig() in userret() as it is no longer
needed.
- Don't grab Giant before psignal() in ast() but get the proc lock instead.
supported architectures such as the alpha. This allows us to save
on kernel virtual address space, TLB entries, and (on the ia64) VHPT
entries. pmap_map() now modifies the passed in virtual address on
architectures that do not support direct-mapped segments to point to
the next available virtual address. It also returns the actual
address that the request was mapped to.
- On the IA64 don't use a special zone of PV entries needed for early
calls to pmap_kenter() during pmap_init(). This gets us in trouble
because we end up trying to use the zone allocator before it is
initialized. Instead, with the pmap_map() change, the number of needed
PV entries is small enough that we can get by with a static pool that is
used until pmap_init() is complete.
Submitted by: dfr
Debugging help: peter
Tested by: me
This lets us run programs containing newer (eg bwx) instructions
on older (eg EV5 and less) machines. One win is that we can
now run Acrobat4 on EV4s and EV5s.
Obtained from: NetBSD
Glanced at by: mjacob
MFS: bring the consistent `compat_3_brand' support
This should fix the linux-related panics reported
by naddy@mips.inka.de (Christian Weisgerber)
Forgotten by: obrien
- Don't hold sched_lock around addupc_task() as this apparently breaks
profiling badly due to sched_lock being held across copyin().
Reported by: bde (2)
work because opt_preemption.h wasn't #include'd. Instead, make use of the
do_switch parameter to ithread_schedule() and do the check in the alpha
interrupt code.
scheduling an interrupt thread to run when needed. This has the side
effect of enabling support for entropy gathering from interrupts on
all architectures.
- Change the software interrupt and x86 and alpha hardware interrupt code
to use ithread_schedule() for most of their processing when scheduling
an interrupt to run.
- Remove the pesky Warning message about interrupt threads having entropy
enabled. I'm not sure why I put that in there in the first place.
- Add more error checking for parameters and change some cases that
returned EINVAL to panic on failure instead via KASSERT().
- Instead of doing a documented evil hack of setting the P_NOLOAD flag
on every interrupt thread whose pri was SWI_CLOCK, set the flag
explicity for clk_ithd's proc during start_softintr().
in mi_switch() just before calling cpu_switch() so that the first switch
after a resched request will satisfy the request.
- While I'm at it, move a few things into mi_switch() and out of
cpu_switch(), specifically set the p_oncpu and p_lastcpu members of
proc in mi_switch(), and handle the sched_lock state change across a
context switch in mi_switch().
- Since cpu_switch() no longer handles the sched_lock state change, we
have to setup an initial state for sched_lock in fork_exit() before we
release it.
Please note:
When committing changes to this file, it is important to note that
linux is not freebsd -- their system call numbers (and sometimes names)
are different on different platforms. When in doubt (and you always need
to be) check the arch-specific unistd.h and entry.S files in the linux
kernel sources to see what the syscall numbers really are.
always on curproc. This is needed to implement signal delivery properly
(see a future log message for kern_sig.c).
Debogotified the definition of aston(). aston() was defined in terms
of signotify() (perhaps because only the latter already operated on
a specified process), but aston() is the primitive.
Similar changes are needed in the ia64 versions of cpu.h and trap.c.
I didn't make them because the ia64 is missing the prerequisite changes
to make astpending and need_resched per-process and those changes are
too large to make without testing.
clear MCPCIA_INT_MASK0 helps things substantially. So, why not indeed?
Rearrange irq and cookie calculation to use shifts/masks instead
of division. Fix things to correctly remember the intpin for that
one in a million non-INTA PCI device.
made no sense in the context of wrapping them within the _SYBRIDGE macro-
or anything like it- so we concluded that this must have been a typo
in the docs. This also doesn't use the same bridge offset as anything
else.
Add some defines for the INT_CTL register.
- All processes go into the same array of queues, with different
scheduling classes using different portions of the array. This
allows user processes to have their priorities propogated up into
interrupt thread range if need be.
- I chose 64 run queues as an arbitrary number that is greater than
32. We used to have 4 separate arrays of 32 queues each, so this
may not be optimal. The new run queue code was written with this
in mind; changing the number of run queues only requires changing
constants in runq.h and adjusting the priority levels.
- The new run queue code takes the run queue as a parameter. This
is intended to be used to create per-cpu run queues. Implement
wrappers for compatibility with the old interface which pass in
the global run queue structure.
- Group the priority level, user priority, native priority (before
propogation) and the scheduling class into a struct priority.
- Change any hard coded priority levels that I found to use
symbolic constants (TTIPRI and TTOPRI).
- Remove the curpriority global variable and use that of curproc.
This was used to detect when a process' priority had lowered and
it should yield. We now effectively yield on every interrupt.
- Activate propogate_priority(). It should now have the desired
effect without needing to also propogate the scheduling class.
- Temporarily comment out the call to vm_page_zero_idle() in the
idle loop. It interfered with propogate_priority() because
the idle process needed to do a non-blocking acquire of Giant
and then other processes would try to propogate their priority
onto it. The idle process should not do anything except idle.
vm_page_zero_idle() will return in the form of an idle priority
kernel thread which is woken up at apprioriate times by the vm
system.
- Update struct kinfo_proc to the new priority interface. Deliberately
change its size by adjusting the spare fields. It remained the same
size, but the layout has changed, so userland processes that use it
would parse the data incorrectly. The size constraint should really
be changed to an arbitrary version number. Also add a debug.sizeof
sysctl node for struct kinfo_proc.
Some things needed bits of <i386/include/lock.h> - cy.c now has its
own (only) copy of the COM_(UN)LOCK() macros, and IMASK_(UN)LOCK()
has been moved to <i386/include/apic.h> (AKA <machine/apic.h>).
Reviewed by: jhb
genassym here, but what I've also noticed is that we're dorking
with a mutex directly at assembler level- I'm not sure that this
is wise at this stage in the SMP port- I think it's going to be much
safer for a while to do things in C until SMP wunderkind figure out
what works and slow down this 3 order differential...
it as I was playing with some other ways of doing kernel preemption.
You must still specify the PREEMPTION option in your config file to get a
preemptive kernel.
attributes. This is needed for AST's to be properly posted in a preemptive
kernel. They are backed by two new flags in p_sflag: PS_ASTPENDING and
PS_NEEDRESCHED. They are still accesssed by their old macros:
aston(), astoff(), etc. For completeness, an astpending() macro has been
added to check for a pending AST, and clear_resched() has been added to
clear need_resched().
- Rename syscall2() on the x86 back to syscall() to be consistent with
other architectures.
- Use swi_* function names.
- Use void * to hold cookies to handlers instead of struct intrhand *.
- In sio.c, use 'driver_name' instead of "sio" as the name of the driver
lock to minimize diffs with cy(4).
mtx_enter(lock, type) becomes:
mtx_lock(lock) for sleep locks (MTX_DEF-initialized locks)
mtx_lock_spin(lock) for spin locks (MTX_SPIN-initialized)
similarily, for releasing a lock, we now have:
mtx_unlock(lock) for MTX_DEF and mtx_unlock_spin(lock) for MTX_SPIN.
We change the caller interface for the two different types of locks
because the semantics are entirely different for each case, and this
makes it explicitly clear and, at the same time, it rids us of the
extra `type' argument.
The enter->lock and exit->unlock change has been made with the idea
that we're "locking data" and not "entering locked code" in mind.
Further, remove all additional "flags" previously passed to the
lock acquire/release routines with the exception of two:
MTX_QUIET and MTX_NOSWITCH
The functionality of these flags is preserved and they can be passed
to the lock/unlock routines by calling the corresponding wrappers:
mtx_{lock, unlock}_flags(lock, flag(s)) and
mtx_{lock, unlock}_spin_flags(lock, flag(s)) for MTX_DEF and MTX_SPIN
locks, respectively.
Re-inline some lock acq/rel code; in the sleep lock case, we only
inline the _obtain_lock()s in order to ensure that the inlined code
fits into a cache line. In the spin lock case, we inline recursion and
actually only perform a function call if we need to spin. This change
has been made with the idea that we generally tend to avoid spin locks
and that also the spin locks that we do have and are heavily used
(i.e. sched_lock) do recurse, and therefore in an effort to reduce
function call overhead for some architectures (such as alpha), we
inline recursion for this case.
Create a new malloc type for the witness code and retire from using
the M_DEV type. The new type is called M_WITNESS and is only declared
if WITNESS is enabled.
Begin cleaning up some machdep/mutex.h code - specifically updated the
"optimized" inlined code in alpha/mutex.h and wrote MTX_LOCK_SPIN
and MTX_UNLOCK_SPIN asm macros for the i386/mutex.h as we presently
need those.
Finally, caught up to the interface changes in all sys code.
Contributors: jake, jhb, jasone (in no particular order)
only covers about 3-4 lines.
- Don't lower the IPL while we are on the interrupt stack. Instead, save
the raised IPL and change the saved IPL in sched_lock to IPL_0 before
calling mi_switch(). When we are resumed, restore the saved IPL in
sched_lock to the saved raised IPL so that when we release sched_lock
we won't lower the IPL. Without this, we would get nested interrupts
that would overflow the kernel stack.
Tested by: mjacob
* Optimise the return path for syscalls so that they only restore a minimal
set of registers instead of performing a full exception_return.
A new flag in the trapframe indicates that the frame only holds partial
state. When it is necessary to perform a full state restore (e.g. after an
execve or signal), the flag is cleared to force a full restore.
- If possible, context switch to the thread directly in sched_ithd(),
rather than triggering a delayed ast reschedule.
- Disable interrupts while restoring fpu state in the trap handler,
in order to ensure that we are not preempted in the middle, which
could cause migration to another cpu.
Reviewed by: peter
Tested by: peter (alpha)
* Optimise the return path for syscalls so that they only restore a minimal
set of registers instead of performing a full exception_return.
A new flag in the trapframe indicates that the frame only holds partial
state. When it is necessary to perform a full state restore (e.g. after an
execve or signal), the flag is cleared to force a full restore.
instead of a trapframe directly. (Requested by bde.)
- Convert the alpha switch_trampoline to call fork_exit() and use the MI
fork_return() instead of child_return().
- Axe child_return().
to extract the PC from that to send to addupc_task() so that it can be
called from MI code.
- Remove all traces of have_giant with extreme prejudice and use
mtx_owned(&Giant) instead where appropriate.
- Proc locking.
- P_FOO -> PS_FOO.
- Don't grab Giant just to look in curproc's p_addr during a trap since we
may choose to immediately exit. Instead, delay grabbing Giant a bit
until we actually need it.
- Don't reset 'p' to 'curproc' in syscall() to handle the case of a child
returning from fork1() since children don't return via syscall().
- Remove an XXX comment in ast() that questions the correctness of the
userland check. The code is correct.
- Don't send IPIs for pmap_invalidate_page() or pmap_invalidate_all()
in the UP case.
- Catch up to cpuno -> cpuid.
- Convert some sanity checks that were #ifdef DIAGNOSTIC to KASSERT()'s.
- Rename the per-CPU variable 'cpuno' to 'cpuid'. This was done so that
there is one consistent name across all architectures for a logical
CPU id.
- Remove all traces of IRQ forwarding.
- Add globaldata_register() hook called by globaldata_init() to register
globaldata structures in the cpuid_to_globaldata array.
- Catch up to P_FOO -> PS_FOO.
- Bring across some fixes for forwarded_statclock() from the i386 version
to handle ithreads and idleproc properly.
- Rename addugd_intr_forwarded() to addupc_intr_forwarded() so that it is
the same name on all architectures.
- Set flags in p_sflag instead of calling psignal() from
forward_hardclock().
- Proc locking.
- When we handle an IPI, turn off its bit in the mask of IPI's we are
currently handling so that an IPI doesn't send a CPU into an infinite
loop.
that mutex operations work.
- Enter Giant earlier so we hold it during boot.
- Proc locking.
- Move globaldata_init() into here from mp_machdep.c so that UP kernels
don't depend on mp_machdep.c. Use a callout in the SMP case to register
the boot processor's globaldata in the cpuid_to_globaldata array.
inline functions non-inlined. Hide parts of the mutex implementation that
should not be exposed.
Make sure that WITNESS code is not executed during boot until the mutexes
are fully initialized by SI_SUB_MUTEX (the original motivation for this
commit).
Submitted by: peter
interrupt threads to run with it always >= 1, so that malloc can
detect M_WAITOK from "interrupt" context. This is also necessary
in order to context switch from sched_ithd() directly.
Reviewed By: peter
initialization until after malloc() is safe to call, then iterate through
all mutexes and complete their initialization.
This change is necessary in order to avoid some circular bootstrapping
dependencies.
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
exactly the same functionality via a sysctl, making this feature
a run-time option.
The default is 1(ON), which means that /dev/random device will
NOT block at startup.
setting kern.random.sys.seeded to 0(OFF) will cause /dev/random
to block until the next reseed, at which stage the sysctl
will be changed back to 1(ON).
While I'm here, clean up the sysctls, and make them dynamic.
Reviewed by: des
Tested on Alpha by: obrien
__FreeBSD_version 500015 can be used to detect their disappearance.
- Move the symbols for SMP_prvspace and lapic from globals.s to
locore.s.
- Remove globals.s with extreme prejudice.
be 64 bits wide. The largest known current actual physical implementation
is 40 bits, so BUS_SPACE_MAXADDR should reflect this. It also seems to
me that BUS_SPACE_UNRESTRICTED should b ~0UL, not ~0.
symbols in globals.s.
PCPU_GET(name) returns the value of the per-cpu variable
PCPU_PTR(name) returns a pointer to the per-cpu variable
PCPU_SET(name, val) sets the value of the per-cpu variable
In general these are not yet used, compatibility macros remain.
Unifdef SMP struct globaldata, this makes variables such as cpuid
available for UP as well.
Rebuilding modules is probably a good idea, but I believe old
modules will still work, as most of the old infrastructure
remains.
of explicit calls to lockmgr. Also provides macros for the flags
pased to specify shared, exclusive or release which map to the
lockmgr flags. This is so that the use of lockmgr can be easily
replaced with optimized reader-writer locks.
- Add some locking that I missed the first time.
CPU version (apecs:ev4::cia:ev5) and the irq hardware depends on the systype
previously, only ev4 AS1000s and ev5 AS1000a's would have worked.
tested by: wilko (in its -stable form)
noticed by: daniel
held and panic if so (conditional on witness).
- Change witness_list to return the number of locks held so this is easier.
- Add kern/syscalls.c to the kernel build if witness is defined so that the
panic message can contain the name of the offending system call.
- Add assertions that Giant and sched_lock are not held when returning from
a system call, which were missing for alpha and ia64.
- Move PCI core code to dev/pci.
- Split bridge code out into separate modules.
- Remove the descriptive strings from the bridge drivers. If you
want to know what a device is, use pciconf. Add support for
broadly identifying devices based on class/subclass, and for
parsing a preloaded device identification database so that if
you want to waste the memory, you can identify *anything* we know
about.
- Remove machine-dependant code from the core PCI code. APIC interrupt
mapping is performed by shadowing the intline register in machine-
dependant code.
- Bring interrupt routing support to the Alpha
(although many platforms don't yet support routing or mapping
interrupts entirely correctly). This resulted in spamming
<sys/bus.h> into more places than it really should have gone.
- Put sys/dev on the kernel/modules include path. This avoids
having to change *all* the pci*.h includes.
files which Compaq open-sourced (with a BSD license).
This commit adds support for proper PCI interrupt mapping and much
better support for swizzling between "standard" isa IRQs and the stdio
irqs used by the t2. This also adds enabling/disabling/eoi support
for AlphaServer 2100A machines. The 2100A (or lynx) interrupt
hardware is is very different (and much nicer) than the 2100.
Previously, only AS2100 and AS2000 machines worked.
This commits also lays the groundwork for supporting ExtIO modules.
These modules are essentially a second hose. This work is left
unfinished pending testing on real hardware. Wilko tells me that
ExtIO modules are quite rare, and may not actually exist in the wild.
Obtained from: Tru64
Tested by: wilko
spending, which was unused now that all software interrupts have
their own thread. Make the legacy schednetisr use an atomic op
for setting bits in the netisr mask.
Reviewed by: jhb
tweak to enable/disable interrupt sources. Seems to work. It is unclear
how many of the PC164 models actually might needs this, and whether or
not there are other hidden issues.
Obtained from:Bernd Walter <ticso@cicely8.cicely.de>
not return ENOEXEC. This is because image activators should return -1 if they
don't claim an image. They should return ENOEXEC if they do claim it,
but cannot load it due to sime problem with the image. This bug was
preventing static compilation of the osf/1 module. I'm surprised it
did not cause more problems.
EOI after the ithread runs, send the EOI when we get the interrupt and
disable the source. After the ithread is run, the source is renabled.
Also, add isa_handle_fast_intr() which handles fast interrupts by sending
an EOI after the handler is run.
This fixes the chronic missing interrupt problems under heavy NFS load
on my UP1000 and should result in greater stability for alphas which
route all irqs through an isa pic.
Discussed with: jhb, bde (sending non-specific EOIs early was bde's idea)
like the args to the config space accessors these functions replaced.
This reduces the likelyhood of overflow when the args are used in
macros on the alpha. This prevents memory management faults when
probing the pci bus on sables, multias and nonames.
Approved by: dfr
Tested by: Bernd Walter <ticso@cicely8.cicely.de>
process is on the alternate stack or not. For compatibility
with sigstack(2) state is being updated if such is needed.
We now determine whether the process is on the alternate
stack by looking at its stack pointer. This allows a process
to siglongjmp from a signal handler on the alternate stack
to the place of the sigsetjmp on the normal stack. When
maintaining state, this would have invalidated the state
information and causing a subsequent signal to be delivered
on the normal stack instead of the alternate stack.
PR: 22286
can unload. Doing so leaves the linuxulator in a crippled
state (no ioctl support) when Linux binaries are run at
unload time.
While here, consistently spell ELF in capitals and perform
some minor style improvements.
ELF spelling submitted by: asmodai
counter register in-CPU.
This is to be used as a fast "timer", where linearity is more important
than time, and multiple lines in the linearity caused by multiple CPUs
in an SMP machine is not a problem.
This adds no code whatsoever to the FreeBSD kernel until it is actually
used, and then as a single-instruction inline routine (except for the
80386 and 80486 where it is some more inline code around nanotime(9).
Reviewed by: bde, kris, jhb
- move the call to cia_init_sgmap() to after we've determined if we're a pyxis
- convert needed splhigh() in cia_sgmap_invalidate_pyxis() to disable_intr()
Previously, any isa DMA on a pyxis based machine would cause a panic
in cia_sgmap_invalidate_pyxis() because the pyxis workaround was never
setup.
- while i'm at it, convert needed splhigh() in cia_swiz_set_hae_mem to
disable_intr()
- Use the mutex in hardclock to ensure no races between it and
softclock.
- Make softclock be INTR_MPSAFE and provide a flag,
CALLOUT_MPSAFE, which specifies that a callout handler does not
need giant. There is still no way to set this flag when
regstering a callout.
Reviewed by: -smp@, jlemon
may block on a mutex while on the sleep queue without corrupting
it.
- Move dropping of Giant to after the acquire of sched_lock.
Tested by: John Hay <jhay@icomtek.csir.co.za>
jhb
acquire Giant as needed in functions that call mi_switch(). The releases
need to be done outside of the sched_lock to avoid potential deadlocks
from trying to acquire Giant while interrupts are disabled.
Submitted by: witness
to our native connect(). This is required to deal with the differences
in the way linux handles connects on non-blocking sockets.
This gets the private beta of the Compaq Linux/alpha JDK working
on FreeBSD/alpha
Approved by: marcel
mainly cut-n-pasted from the i386 port, except for the method of setting
the child's stack which is the only MD part of this function.
I've tested with the example apps shipped with the linux threads source
code (ex1-ex6) and with several binary builds of Mozilla.
- No signal translation is needed. Our signals match the OSF/1 signals
- an OSF/1 sigset_t is 64 bits. Make certain to use all 64-bits of it.
We'd previously only used the lower 32 bits. This was mostly harmless
as I don't know of an OSF/1 apps which use any signals > 31. However,
the alpha Linux ABI uses the osf/1 signal routines and threaded linux
apps tyically use signals 32 and 33 to comminicate with the manager
thread, so it is important we preserve the upper 32-bits.
Reviewed by: marcel (at least in principal)
syscall compare against a variable sv_minsigstksz in struct
sysentvec as to properly take the size of the machine- and
ABI dependent struct sigframe into account.
The SVR4 and iBCS2 modules continue to have a minsigstksz of
8192 to preserve behavior. The real values (if different) are
not known at this time. Other ABI modules use the real
values.
The native MINSIGSTKSZ is now defined as follows:
Arch MINSIGSTKSZ
---- -----------
alpha 4096
i386 2048
ia64 12288
Reviewed by: mjacob
Suggested by: bde
for an interrupt to enable/disable from the vector (and GID too, if we
had multiple GIDs)- so, stupidly for now, search for the right mcpcia's
softc so we have the right base address for the bridge CSR to apply
IRQ bit-twiddle's to. Alas- this doesn't yet allow us to run, but it's
the right direction.
Previously we had to include <machine/param.h> or <sys/param.h> bogusly
due to the fact that <sys/socket.h> CMSG macros needed the ALIGN macro,
which was defined in param.h. However, including param.h was a disaster
for namespace pollution.
This solution, as contributed by shin a while ago, fixes it elegantly
by wrapping the definitions around some namespace pollution preventer
definitions.
This patch was long overdue.
This should allow any network programmer to use <sys/socket.h> as
before.
PR: 19971, 20530
Submitted by: Martin Kaeske <MartinKaeske@lausitz.net>
Mark Andrews <Mark.Andrews@nominum.com>
Patch submitted by: shin
Reviewed by: bde
argument. These flags include INTR_FAST, INTR_MPSAFE, etc.
- Properly handle INTR_EXCL when it is passed in to allow an interrupt
handler to claim exclusive ownership of an interrupt thread.
- Add support for psuedo-fast interrupts on the alpha. For fast interrupts,
we don't allocate an interrupt thread; instead, during dispatching of an
interrupt, we run the handler directly instead of scheduling the thread
to run. Note that the handler is currently run without Giant and must be
MP safe. The only fast handler currently is for the sio driver.
Requested by: dfr
because it only takes a struct tag which makes it impossible to
use unions, typedefs etc.
Define __offsetof() in <machine/ansi.h>
Define offsetof() in terms of __offsetof() in <stddef.h> and <sys/types.h>
Remove myriad of local offsetof() definitions.
Remove includes of <stddef.h> in kernel code.
NB: Kernelcode should *never* include from /usr/include !
Make <sys/queue.h> include <machine/ansi.h> to avoid polluting the API.
Deprecate <struct.h> with a warning. The warning turns into an error on
01-12-2000 and the file gets removed entirely on 01-01-2001.
Paritials reviews by: various.
Significant brucifications by: bde
change_ruid() in kern_prot.c. This fixes an incorrect use
of chgproccnt().
Update both osf1_setuid() and osf1_setgid() to use setsugid() instead
of just frobbing the flag.
(mostly) submitted by: truckman
type of software interrupt. Roughly, what used to be a bit in spending
now maps to a swi thread. Each thread can have multiple handlers, just
like a hardware interrupt thread.
- Instead of using a bitmask of pending interrupts, we schedule the specific
software interrupt thread to run, so spending, NSWI, and the shandlers
array are no longer needed. We can now have an arbitrary number of
software interrupt threads. When you register a software interrupt
thread via sinthand_add(), you get back a struct intrhand that you pass
to sched_swi() when you wish to schedule your swi thread to run.
- Convert the name of 'struct intrec' to 'struct intrhand' as it is a bit
more intuitive. Also, prefix all the members of struct intrhand with
'ih_'.
- Make swi_net() a MI function since there is now no point in it being
MD.
Submitted by: cp
more include file including <sys/proc.h>, but there still is this wonky
and (causes warnings on i386) reference in globals.h.
CURTHD is now defined in <machine/globals.h> as well. The correct thing
to do is provide a platform function for this.
reducues the maintenance load for the mutex code. The only MD portions
of the mutex code are in machine/mutex.h now, which include the assembly
macros for handling mutexes as well as optionally overriding the mutex
micro-operations. For example, we use optimized micro-ops on the x86
platform #ifndef I386_CPU.
- Change the behavior of the SMP_DEBUG kernel option. In the new code,
mtx_assert() only depends on INVARIANTS, allowing other kernel developers
to have working mutex assertiions without having to include all of the
mutex debugging code. The SMP_DEBUG kernel option has been renamed to
MUTEX_DEBUG and now just controls extra mutex debugging code.
- Abolish the ugly mtx_f hack. Instead, we dynamically allocate
seperate mtx_debug structures on the fly in mtx_init, except for mutexes
that are initiated very early in the boot process. These mutexes
are declared using a special MUTEX_DECLARE() macro, and use a new
flag MTX_COLD when calling mtx_init. This is still somewhat hackish,
but it is less evil than the mtx_f filler struct, and the mtx struct is
now the same size with and without mutex debugging code.
- Add some micro-micro-operation macros for doing the actual atomic
operations on the mutex mtx_lock field to make it easier for other archs
to override/optimize mutex ops if needed. These new tiny ops also clean
up the code in some places by replacing long atomic operation function
calls that spanned 2-3 lines with a short 1-line macro call.
- Don't call mi_switch() from mtx_enter_hard() when we block while trying
to obtain a sleep mutex. Calling mi_switch() would bogusly release
Giant before switching to the next process. Instead, inline most of the
code from mi_switch() in the mtx_enter_hard() function. Note that when
we finally kill Giant we can back this out and go back to calling
mi_switch().
in most of the atomic operations. Now for these operations, you can
use the normal atomic operation, you can use the operation with a read
barrier, or you can use the operation with a write barrier. The function
names follow the same semantics used in the ia64 instruction set. An
atomic operation with a read barrier has the extra suffix 'acq', due to
it having "acquire" semantics. An atomic operation with a write barrier
has the extra suffix 'rel'. These suffixes are inserted between the
name of the operation to perform and the typename. For example, the
atomic_add_int() function now has 3 variants:
- atomic_add_int() - this is the same as the previous function
- atomic_add_acq_int() - this function combines the add operation with a
read memory barrier
- atomic_add_rel_int() - this function combines the add operation with a
write memory barrier
- Add 'ptr' to the list of types that we can perform atomic operations
on. This allows one to do atomic operations on uintptr_t's. This is
useful in the mutex code, for example, because the actual mutex lock is
a pointer.
- Add two new operations for doing loads and stores with memory barriers.
The new load operations use a read barrier before the load, and the
new store operations use a write barrier after the load. For example,
atomic_load_acq_int() will atomically load an integer as well as
enforcing a read barrier.
write caching is disabled on both SCSI and IDE disks where large
memory dumps could take up to an hour to complete.
Taking an i386 scsi based system with 512MB of ram and timing (in
seconds) how long it took to complete a dump, the following results
were obtained:
Before: After:
WCE TIME WCE TIME
------------------ ------------------
1 141.820972 1 15.600111
0 797.265072 0 65.480465
Obtained from: Yahoo!
Reviewed by: peter
and associated user-level signal trampoline glue.
Without this patch, an SA_SIGINFO style handler can be installed by a linux
app, but if the handler accesses its sip argument, it will get a garbage
pointer and likely segfault.
We currently supply a valid pointer, but its contents are mainly
garbage. Filling this in properly is future work.
This is the second of 3 commits that will get IBM's JDK 1.3 working with
FreeBSD ...
loads, prints the copyright, and either hangs or locks solid. The
PC tends to be in the data segment and the RA is in XentMM
Doug really came up with the fix, I'm just the monkey typing. Doug says:
The alpha can only support 64k of globals with $gp pointing at
base+32k so that the code can use 16bit signed offsets from $gp to
access it. .... it is possible to have multiple .got subsections
and the linker handles this with the relocations for 'ldgp' pseudo
instructions. [Without this patch] the code in exception.s has been
linked to use a different gp from locore.s (where pal_kgp is set).
Reviewed by: dfr
Before calling kernacc(), make sure that we're not calling it
with a K0SEG address.
This gets alphas booting with SMP_DEBUG & INVARIANTS options
approved by: jhb
Replace all in-tree uses with <sys/mouse.h> which repo-copied a few
moments ago from src/sys/i386/include/mouse.h by peter.
This is also the appropriate fix for exo-tree sources.
Put warnings in <machine/mouse.h> to discourage use.
November 15th 2000 the warnings will be converted to errors.
January 15th 2001 the <machine/mouse.h> files will be removed.
Replace all in-tree uses with necessary subset of <sys/{fb,kb,cons}io.h>.
This is also the appropriate fix for exo-tree sources.
Put warnings in <machine/console.h> to discourage use.
November 15th 2000 the warnings will be converted to errors.
January 15th 2001 the <machine/console.h> files will be removed.
check in the [basic.link] section of the C++ standard wrong. gcc-2.7.2.3
apparently doesn't do the check, so the bug doesn't affect RELENG_3.
PR: 16170, 21427
Submitted by: Max Khon <fjoe@lark.websci.ru> (i386 version)
Discussed with: jdp
return through doreti to handle ast's. This is necessary for the
clock interrupts to work properly.
- Change the clock interrupts on the x86 to be fast instead of threaded.
This is needed because both hardclock() and statclock() need to run in
the context of the current process, not in a separate thread context.
- Kill the prevproc hack as it is no longer needed.
- We really need Giant when we call psignal(), but we don't want to block
during the clock interrupt. Instead, use two p_flag's in the proc struct
to mark the current process as having a pending SIGVTALRM or a SIGPROF
and let them be delivered during ast() when hardclock() has finished
running.
- Remove CLKF_BASEPRI, which was #ifdef'd out on the x86 anyways. It was
broken on the x86 if it was turned on since cpl is gone. It's only use
was to bogusly run softclock() directly during hardclock() rather than
scheduling an SWI.
- Remove the COM_LOCK simplelock and replace it with a clock_lock spin
mutex. Since the spin mutex already handles disabling/restoring
interrupts appropriately, this also lets us axe all the *_intr() fu.
- Back out the hacks in the APIC_IO x86 cpu_initclocks() code to use
temporary fast interrupts for the APIC trial.
- Add two new process flags P_ALRMPEND and P_PROFPEND to mark the pending
signals in hardclock() that are to be delivered in ast().
Submitted by: jakeb (making statclock safe in a fast interrupt)
Submitted by: cp (concept of delaying signals until ast())
- Make softinterrupts (SWI's) almost completely MI, and divorce them
completely from the x86 hardware interrupt code.
- The ihandlers array is now gone. Instead, there is a MI shandlers array
that just contains SWI handlers.
- Most of the former machine/ipl.h files have moved to a new sys/ipl.h.
- Stub out all the spl*() functions on all architectures.
Submitted by: dfr
to accomodate the changes.
Here's a list of things that have changed (I may have left out a few); for a
relatively complete list, see http://people.freebsd.org/~bmilekic/mtx_journal
* Remove old (once useful) mcluster code for MCLBYTES > PAGE_SIZE which
nobody uses anymore. It was great while it lasted, but now we're moving
onto bigger and better things (Approved by: wollman).
* Practically re-wrote the allocation macros in sys/sys/mbuf.h to accomodate
new allocations which grab the necessary lock.
* Make sure that necessary mbstat variables are manipulated with
corresponding atomic() routines.
* Changed the "wait" routines, cleaned it up, made one routine that does
the job.
* Generalized MWAKEUP() macro. Got rid of m_retry and m_retryhdr, as they
are now included in the generalized "wait" routines.
* Sleep routines now use msleep().
* Free lists have locks.
* etc... probably other stuff I'm missing...
Things to look out for and work on later:
* find a better way to (dynamically) adjust EXT_COUNTERS
* move necessity to recurse on a lock from drain routines by providing
lock-free lower-level version of MFREE() (and possibly m_free()?).
* checkout include of mutex.h in sys/sys/mbuf.h - probably violating
general philosophy here.
The code has been reviewed quite a bit, but problems may arise... please,
don't panic! Send me Emails: bmilekic@freebsd.org
Reviewed by: jlemon, cp, alfred, others?
Previously, these cards were supported by the lnc driver (and they
still are, but the pcn driver will claim them first), which is fine
except the lnc driver runs them in 16-bit LANCE compatibility mode.
The pcn driver runs these chips in 32-bit mode and uses the RX alignment
feature to achieve zero-copy receive. (Which puts it in the same
class as the xl, fxp and tl chipsets.) This driver is also MI, so it
will work on the x86 and alpha platforms. (The lnc driver is still
needed to support non-PCI cards. At some point, I'll need to newbusify
it so that it too will me MI.)
The Am79c978 HomePNA adapter is also supported.
newbus for referencing device interrupt handlers.
- Move the 'struct intrec' type which describes interrupt sources into
sys/interrupt.h instead of making it just be a x86 structure.
- Don't create 'ithd' and 'intrec' typedefs, instead, just use 'struct ithd'
and 'struct intrec'
- Move the code to translate new-bus interrupt flags into an interrupt thread
priority out of the x86 nexus code and into a MI ithread_priority()
function in sys/kern/kern_intr.c.
- Remove now-uneeded x86-specific headers from sys/dev/ata/ata-all.c and
sys/pci/pci_compat.c.
re-enable interrupts when actually releasing the lock.
- Bring across some fixes to propagate_priority from the x86 code.
(It still doesn't work properly, however.)
- Use the SMTX state when putting a process that blocks on a mutex to sleep.
- Use mi_switch instead of cpu_switch so that accounting works properly as
well as other things.
- Bring across DDB protection of the spinlock timeout panic which is useful
in a multiple CPU system when 1 CPU enters the debugger holding the
sched_lock so that the other CPU doesn't panic as well resulting in all
sorts of fun things.
- Bring across various other small changes in format strings and comments
to sync up with the x86 code.
fixes a serious problem with the previous version where an input could
have been placed in the same register as an output which would stop
the inline from working properly.
* Redo atomic_{set,clear,add,subtract}_{32,64} as inlines since the code
sequence is shorter than the call sequence to the code in atomic.s.
I will remove the functions from atomic.s after a grace period to allow
people to rebuild kernel modules.
and mtx_exit(). This change tracks the i386 version.
Rename mtx_enter(), mtx_try_enter(), and mtx_exit() and wrap them with cpp
macros that expand to pass filename and line number information. This is
necessary since we're using inline functions instead of macros now.
Add const to the filename pointers passed througout the mtx and witness
code.
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
machines. The patch uses an existing global variable in place of the
newbus accessor to get at use_bwx.
This is a quick fix to get miatas booting again; somebody
with more newbus skills than I can muster will have to correct it.
Matt Jacob's description of the problem from the -alpha list:
The IVAR accessor stuff for pcib is incompletely specified for CIA. There's
only one accessor defined, and that's to get the BUS instance number.
<..>
The device methods that try and get at the use_bwx get overriden because
there's only one ivar for CIA's pcib, and that's for hose #, and it's always
zero.
foo_pcib_[read|write]_config() functions rather than relying on
a break or return being in the CFG macro.
This fixes a panic later in the boot process on a UP1000. From
inspection, it looks like this fixes a similar problem in the tsunami code.
Approved by: dfr
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
In summary:
o This file has been moved to sys/compat/linux,
o Any MD syscalls in this file are moved to
linux_machdep.c in sys/i386/linux,
o Include directives, makefiles and config files
have been updated.
that should be better.
The old code counted references to mbuf clusters by using the offset
of the cluster from the start of memory allocated for mbufs and
clusters as an index into an array of chars, which did the reference
counting. If the external storage was not a cluster then reference
counting had to be done by the code using that external storage.
NetBSD's system of linked lists of mbufs was cosidered, but Alfred
felt it would have locking issues when the kernel was made more
SMP friendly.
The system implimented uses a pool of unions to track external
storage. The union contains an int for counting the references and
a pointer for forming a free list. The reference counts are
incremented and decremented atomically and so should be SMP friendly.
This system can track reference counts for any sort of external
storage.
Access to the reference counting stuff is now through macros defined
in mbuf.h, so it should be easier to make changes to the system in
the future.
The possibility of storing the reference count in one of the
referencing mbufs was considered, but was rejected 'cos it would
often leave extra mbufs allocated. Storing the reference count in
the cluster was also considered, but because the external storage
may not be a cluster this isn't an option.
The size of the pool of reference counters is available in the
stats provided by "netstat -m".
PR: 19866
Submitted by: Bosko Milekic <bmilekic@dsuper.net>
Reviewed by: alfred (glanced at by others on -net)
gcc's internal exit() prototypes and the (futile) hackery that we did to
try and avoid warnings. main() was renamed for similar reasons.
Remove an exit related hack from makesyscalls.sh.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
hose are 16 PCI instances apart. This allows us to recognize secondary
PCI busses (at least to a first level) until the pci infrastructure is
fixed.
Turn on support for secondary cycles, too. Redo debug printouts.
Instead, for now (until we get a pci infrastructure cleanup),
assign the PCI bus number to be mcpcia bus instance << 4. This
is to allow secondary bridges some room to be recongnized on
4100 systems.
SYSCTL_LONG macro to be consistent with other integer sysctl variables
and require an initial value instead of assuming 0. Update several
sysctl variables to use the unsigned types.
PR: 15251
Submitted by: Kelly Yancey <kbyanc@posi.net>
irongate chipset (used in the UP1000) which does not support scatter/gather
DMA. We'll still use scatter gather if the core logic chipset supports it.
Reviewed by: dfr
fields, not lex/yacc grammar so it is not an exact match but should be
close enough for most cases.
Deal with 'port?', 'irq?' style specifications. These are parsed as
seperate values in lex/yacc in config(8) but tripped up this helper tool.
deal with filename arguments. It is amazing how much you forget over time.
Thanks to the people that reminded me this. I knew there was an easy way
that didn't involve messing with $argv, filehandles, etc, but just could
not remember - all of my books are on the opposite side of the planet..
Use Warner Losh's "hint" driver to decode ascii strings to fill the
resource table at boot time.
config(8) no longer generates an ioconf.c table - ie: the configuration
no longer has to be compiled into the kernel. You can reconfigure your
isa devices with the likes of this at loader(8) time:
set hint.ed.0.port=0x320
userconfig will be rewritten to use this style interface one day and will
move to /boot/userconfig.4th or something like that.
It is still possible to statically compile in a set of hints into a kernel
if you do not wish to use loader(8). See the "hints" directive in GENERIC
as an example.
All device wiring has been moved out of config(8). There is a set of
helper scripts (see i386/conf/gethints.pl, and the same for alpha and pc98)
that extract the 'at isa? port foo irq bar' from the old files and produces
a hints file. If you install this file as /boot/device.hints (and update
/boot/defaults/loader.conf - You can do a build/install in sys/boot) then
loader will load it automatically for you. You can also compile in the
hints directly with: hints "device.hints" as well.
There are a few things that I'm not too happy with yet. Under this scheme,
things like LINT would no longer be useful as "documentation" of settings.
I have renamed this file to 'NOTES' and stored the example hints strings
in it. However... this is not something that config(8) understands, so
there is a script that extracts the build-specific data from the
documentation file (NOTES) to produce a LINT that can be config'ed and
built. A stack of man4 pages will need updating. :-/
Also, since there is no longer a difference between 'device' and
'pseudo-device' I collapsed the two together, and the resulting 'device'
takes a 'number of units' for devices that still have it statically
allocated. eg: 'device fe 4' will compile the fe driver with NFE set
to 4. You can then set hints for 4 units (0 - 3). Also note that
'device fe0' will be interpreted as "zero units of 'fe'" which would be
bad, so there is a config warning for this. This is only needed for
old drivers that still have static limits on numbers of units.
All the statically limited drivers that I could find were marked.
Please exercise EXTREME CAUTION when transitioning!
Moral support by: phk, msmith, dfr, asmodai, imp, and others
loader for alpha (Yay!) we still need to explicitly look for boot_verbose-
I assume because the boothowto flags aren't passed to us at boot like x86.
Do some minor cosmetics as well.
Only PCI and on-board ISA peripherials are supported at this time.
This support has been only lightly tested due to a lack of response to my
call for testers on the freebsd-alpha mailing list. It works quite well
on the one AS2100 on which it has been tested, but it may not work on
an AS2100A and should therefore be regarded as experimental.
to various pmap_*() functions instead of looking up the physical address
and passing that. In many cases, the first thing the pmap code was doing
was going to a lot of trouble to get back the original vm_page_t, or
it's shadow pv_table entry.
Inspired by: John Dyson's 1998 patches.
Also:
Eliminate pv_table as a seperate thing and build it into a machine
dependent part of vm_page_t. This eliminates having a seperate set of
structions that shadow each other in a 1:1 fashion that we often went to
a lot of trouble to translate from one to the other. (see above)
This happens to save 4 bytes of physical memory for each page in the
system. (8 bytes on the Alpha).
Eliminate the use of the phys_avail[] array to determine if a page is
managed (ie: it has pv_entries etc). Store this information in a flag.
Things like device_pager set it because they create vm_page_t's on the
fly that do not have pv_entries. This makes it easier to "unmanage" a
page of physical memory (this will be taken advantage of in subsequent
commits).
Add a function to add a new page to the freelist. This could be used
for reclaiming the previously wasted pages left over from preloaded
loader(8) files.
Reviewed by: dillon
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
/dev/?random devices. This appears to have been missed when the code
was brought across from the i386. (This should fix the "world build
hangs with everything waiting on 'temp' problem.)
Also add some iovec fixup code in the error path which seems to have
been similarly fixed.
There are a number of other differences between the i386 and alpha
version which have not been examined. This code should still be
considered suspect.
the negative of their blue-box (UNIX/OVMS) counterpart. This was
causing us to panic early in the boot process because we weren't
expecting a negative index into the cpuinit[] array.
Obtained from: NetBSD
Reported by: Brett Bump <bbump@mail.enetis.net>
chipsets. An example of this is the USB controller on these chipsets.
With this, I can now use USB devices on the test Alpha I am borrowing at
the moment.
Reviewed by: dfr, obrien
syscalls including exit(). These entries were unused, so the bugs had no
effect, but the the args struct tag will be used to calculate sy_nargs
correctly. exit() was wrong in all emulators.
like to see the true SRM bus number be passed to us, instead, we get FreeBSD's
PCI bus instance number (Brzzt! Wrong Answer!).
Also, once we've seen the MCPCIA that has the EISA bus on it, call
dec_kn300_cons_init just before configuring devices on this bus.
We'll call it later when, in the natural order of things, we configure
the MCPCIA that has the EISA bus that a serial console and/or VGA and/or
keyboard.
same functionality. Sharing code should help cache issues.
Remove in_cksum_partial, since its not being used, and we now have
a way to compute partial checksums on mbuf chains.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
Remove evil allocation macros from machdep.c (why was that there???) and
use malloc() instead.
Move paramters out of param.h and into the code itself.
Move a bunch of internal definitions from public sys/*.h headers (without
#ifdef _KERNEL even) into the code itself.
I had hoped to make some of this more dynamic, but the cost of doing
wakeups on all sleeping processes on old arrays was too frightening.
The other possibility is to initialize on the first use, and allow
dynamic sysctl changes to parameters right until that point. That would
allow /etc/rc.sysctl to change SEM* and MSG* defaults as we presently
do with SHM*, but without the nightmare of changing a running system.
program running under linux emulation, the script binary is checked for
in /compat/linux first. Without this patch the wrong script binary
(i.e. the FreeBSD binary) will be run instead of the linux binary.
For example, #!/bin/sh, thus breaking out of linux compatibility mode.
This solves a number of problems people have had installing linux
software on FreeBSD boxes.
maintainers.
After we established our branding method of writing upto 8 characters of
the OS name into the ELF header in the padding; the Binutils maintainers
and/or SCO (as USL) decided that instead the ELF header should grow two new
fields -- EI_OSABI and EI_ABIVERSION. Each of these are an 8-bit unsigned
integer. SCO has assigned official values for the EI_OSABI field. In
addition to this, the Binutils maintainers and NetBSD decided that a better
ELF branding method was to include ABI information in a ".note" ELF
section.
With this set of changes, we will now create ELF binaries branded using
both "official" methods. Due to the complexity of adding a section to a
binary, binaries branded with ``brandelf'' will only brand using the
EI_OSABI method. Also due to the complexity of pulling a section out of an
ELF file vs. poking around in the ELF header, our image activator only
looks at the EI_OSABI header field.
Note that a new kernel can still properly load old binaries except for
Linux static binaries branded in our old method.
*
* For a short period of time, ``ld'' will also brand ELF binaries
* using our old method. This is so people can still use kernel.old
* with a new world. This support will be removed before 5.0-RELEASE,
* and may not last anywhere upto the actual release. My expiration
* time for this is about 6mo.
*
Exceptions:
Vinum untouched. This means that it cannot be compiled.
Greg Lehey is on the case.
CCD not converted yet, casts to struct buf (still safe)
atapi-cd casts to struct buf to examine B_PHYS
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
(Much of this done by script)
Move B_ORDERED flag to b_ioflags and call it BIO_ORDERED.
Move b_pblkno and b_iodone_chain to struct bio while we transition, they
will be obsoleted once bio structs chain/stack.
Add bio_queue field for struct bio aware disksort.
Address a lot of stylistic issues brought up by bde.
via sysctl. It's done pretty simply but it should be quite adequate.
Also move SHMMAXPGS from $machine/include/vmparam.h as the comments that
went with it were wrong... we don't allocate KVM space for the pages so
that comment is bogus.. The only practical limit is how much physical
ram you want to lock up as this stuff isn't paged out or swap backed.
syscall path inward. A system call may select whether it needs the MP
lock or not (the default being that it does need it).
A great deal of conditional SMP code for various deadended experiments
has been removed. 'cil' and 'cml' have been removed entirely, and the
locking around the cpl has been removed. The conditional
separately-locked fast-interrupt code has been removed, meaning that
interrupts must hold the CPL now (but they pretty much had to anyway).
Another reason for doing this is that the original separate-lock for
interrupts just doesn't apply to the interrupt thread mechanism being
contemplated.
Modifications to the cpl may now ONLY occur while holding the MP
lock. For example, if an otherwise MP safe syscall needs to mess with
the cpl, it must hold the MP lock for the duration and must (as usual)
save/restore the cpl in a nested fashion.
This is precursor work for the real meat coming later: avoiding having
to hold the MP lock for common syscalls and I/O's and interrupt threads.
It is expected that the spl mechanisms and new interrupt threading
mechanisms will be able to run in tandem, allowing a slow piecemeal
transition to occur.
This patch should result in a moderate performance improvement due to
the considerable amount of code that has been removed from the critical
path, especially the simplification of the spl*() calls. The real
performance gains will come later.
Approved by: jkh
Reviewed by: current, bde (exception.s)
Some work taken from: luoqi's patch
fragmentation problem due to geteblk() reserving too much space for the
buffer and imposes a larger granularity (16K) on KVA reservations for
the buffer cache to avoid fragmentation issues. The buffer cache size
calculations have been redone to simplify them (fewer defines, better
comments, less chance of running out of KVA).
The geteblk() fix solves a performance problem that DG was able reproduce.
This patch does not completely fix the KVA fragmentation problems, but
it goes a long way
Mostly Reviewed by: bde and others
Approved by: jkh
field in struct buf: b_iocmd. The b_iocmd is enforced to have
exactly one bit set.
B_WRITE was bogusly defined as zero giving rise to obvious coding
mistakes.
Also eliminate the redundant struct buf flag B_CALL, it can just
as efficiently be done by comparing b_iodone to NULL.
Should you get a panic or drop into the debugger, complaining about
"b_iocmd", don't continue. It is likely to write on your disk
where it should have been reading.
This change is a step in the direction towards a stackable BIO capability.
A lot of this patch were machine generated (Thanks to style(9) compliance!)
Vinum users: Greg has not had time to test this yet, be careful.
- Microsoft IntelliMouse Explorer: 2 buttons on top, 2 side buttons
and a wheel which also acts as the middle button. The mouse is
recognized as "IntelliMouse Explorer".
- Genius NetScroll Optical: 2 buttons on top, 2 side buttons and a
wheel which also acts as the middle button. The mouse is recognized
as "NetMouse/NetScroll Optical".
- MouseSystems SmartScroll Mouse (OEM from Genius?): 3 buttons on top,
1 side button and a wheel. The mouse is recognized as Genius
"NetScroll".
- IBM ScrollPoint: 2 buttons on top and a stick between the buttons.
The stick can perform "horizontal scroll" in W*ndows environment.
The horizontal movement of the stick is detected. It is currently
mapped to the Z axis movement in the same way as the first wheel.
The mouse is recognized as "MouseMan+", as it is considered to be
a variation of MouseMan.
- A4 Tech 4D and 4D+ mice. These mice have two wheels! The movement
of the second wheel is reported as the Z axis movement in the
same way as the first wheel. These mice are recognized as "4D
Mouse" and "4D+ Mouse".
- Tweak IntelliMouse support code a bit so that less-than-compatible
wheel mice can work properly with the psm driver.
- Add driver configuration flags which correspond to the kernel
options PSM_HOOKRESUME and PSM_RESETAFTERSUSPEND, so that we don't
need to recompile the kernel when we need these functions.
- Properly keep track of the irq resource.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).
from DWLPX to PCI space. Just a methods holder such that we have a parent
which is a "pcib" and we create a child which is a "pci". Add the appropriate
ivar code (which is for a hose #).
based upon presence/absence of ISA (there is no ISA bus on an 8200- okay,
well, there *could* be one in a DWLPX tray, but we don't support it)).
Most importantly change the interrupt resource map to cover a whole 16
bits. The 8200 uses 16 bit interrupt vectors which we construct that
contain the I/O-board, hose, an pci slot in them, and then we write these
vectors into the appropriate DWLPX registers. At any rate, a flat array
of 64 'IRQs' isn't enough.
to begin with. Redo newbus attachment code so that all the DMA mapping
and further pci attachment is done right. Insert config space functions
(jeez- how do you do type 1 cycles?). Do the interrupt setups, etc.
Basically, this is the core I/O module for 8200s, even though logically
it's the 3rd level down from the nominal principle backplane bus
(turbolaser). Still to be done here: S/G code isn't done yet, so we
better live with 2GB or less primary memory.
code (merge in progress made in NetBSD since the initial import to
FreeBSD). Create dwlpx as the child device. Of course, if we had
more h/w and time, we could find out whether the child device was
a FutureBus module, etc...Anyone ever actually seen one?
clean MI/MD driver, but it *does* actually work at this time. Updated
to use new make_dev stuff. A CONS_DRIVER declaration is also put in
so that this can be the real console for the 8200s.
with the known bogus currtpriority. This undoes the previous changes to
sys/i386/i386/trap.c, sys/alpha/alpha/trap.c, sys/sys/systm.h
Now we have the patch set approved by bde.
Approved by: bde
just the first one.
* Don't reserve extra memory for the prom console unless the platform
actually uses it.
* Fix some historical confusion and a minor bug in the message buffer
initialisation.
Submitted by: gallatin for the prom console part
Approved by: jkh
First, it was failing to reset the PCB's pcb_onfault member to NULL.
Under some really obscure circumstances this might cause a wild jump
within the kernel when a panic would otherwise occur. Second, the
handler was loading the GP register needlessly and with an incorrect
value.
Reviewed by: Doug Rabson <dfr>
Approved by: Jordan Hubbard <jkh>
was needed to make attach/detach of devices work, which is
needed for the PCCARD support.
(PCCARD support is still not working though, more to come on that)
Support the CMD646 chip which is used on many alphas, sadly only
in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes.
Lots of cosmetic fixes here and there.
Sorry for the size of this megapatchfromhell but it was not
possible otherwise...
newbus patches based on work from: dfr (Doug Rabson)
fixes some namespace pollution in general and breakage of modules that
aren't in the sys tree in particular (<machine/ipl.h> includes further
headers that aren't installed under /usr/include).
Reimplemented SPLASSERT() so that it is more machine independent and
less bloated and doesn't require the <machine/ipl.h> include spam.
In particular, don't assume that `cpl' can be printed using %08x
format. The alpha arch doesn't even have `cpl'. SPLASSERT() was
harmless on alphas because it isn't actually used.
code & it survives a buildworld. So remove the dire warnings about
Noritake support being untested.
o Remove a disconserting printf() left over from NetBSD
Approved by: jkh
- only allocate rusage struct when caller wants rusage info
- fix a stupid paren mismatch bug that was causing EPERM to get returned
to callers rather then ECHILD
o Drop all broadcast and multicast source addresses in tcp_input.
o Enable ICMP_BANDLIM in GENERIC.
o Change default to 200/s from 100/s. This will still stop the attack, but
is conservative enough to do this close to code freeze.
This is not the optimal patch for the problem, but is likely the least
intrusive patch that can be made for this.
Obtained from: Don Lewis and Matt Dillon.
Reviewed by: freebsd-security
I was wagering on DEC being elegant & numbering PCI buses normally on
machines with one pchip. It looks like they went with consistent -- buses
behind ppbs begin with bus 2.
delivering SIGBUS). This will allow a non-superuser to control unaligned
access behaviour on a per-process basis once a userland control program
(uac) is written.
Reviewed by: obrien
Tested by: obrien
unless both "option INVARIANTS" and "options INVARIANT_SUPPORT"
are defined in the kernel's config(8) file.
SPLASSERT(expression, msg) used KASSERT to check that the
expression is true, panic()ing the kernel otherwise.
Approved by: jkh
Reviewed by: jdp, dfr, phk, eivind and green
USB-EL1202A chipset. Between this and the other two drivers, we should
have support for pretty much every USB ethernet adapter on the market.
The only other USB chip that I know of is the SMC USB97C196, and right
now I don't know of any adapters that use it (including the ones made
by SMC :/ ).
Note that the CATC chip supports a nifty feature: read and write combining.
This allows multiple ethernet packets to be transfered in a single USB
bulk in/out transaction. However I'm again having trouble with large
bulk in transfers like I did with the ADMtek chip, which leads me to
believe that our USB stack needs some work before we can really make
use of this feature. When/if things improve, I intend to revisit the
aue and cue drivers. For now, I've lost enough sanity points.
ddb is entered. Don't refer to `in_Debugger' to see if we
are in the debugger. (The variable used to be static in Debugger()
and wasn't updated if ddb is entered via traps and panic anyway.)
- Don't refer to `in_Debugger'.
- Add `db_active' to i386/i386/db_interface.d (as in
alpha/alpha/db_interface.c).
- Remove cnpollc() stub from ddb/db_input.c.
- Add the dbctl function to syscons, pcvt, and sio. (The function for
pcvt and sio is noop at the moment.)
Jointly developed by: bde and me
(The final version was tweaked by me and not reviewed by bde. Thus,
if there is any error in this commit, that is entirely of mine, not
his.)
Some changes were obtained from: NetBSD
hinted at in the previous config(8) commits. I've spoken about this with
a few people and after the initial suprise wore off they thought it wasn't
a bad idea. The upshot of it is that all the files*, Makefile*, options*
files are all right next to each other in the hope that people making
changes to one set will remember the others.
Note, config(8) looks to sys/conf first, and falls back to sys/$mach/conf
still, so this doesn't stop people working in subdirs for new platforms.
But once it's in the tree it can be moved next to the other files so that
the non-i386 platforms are (hopefully) treated a little better than as if
they were "second class" ports.
This does not change any user editable files. the config program is
still run in the same directory as before, the per-platform files
(GENERIC, LINT etc) are still in the same place.
it's always true on these platforms (and is likely to be on others as
well since loader is the one that is configured for whatever the boot
requirements are)
\begin{quote}
Compile genassym.c with ordinary ${CFLAGS}. The (small) needs for
${GEN_CFLAGS} and -U_KERNEL became negative when all all the
genassym.c's were converted to be cross-built.
Makefile.*:
- Cleanups associated with the old genassym.
- Fixed deprecated spelling of ${.IMPSRC} as "$<".
\end{quote}
Submitted by: bde
Kawasaki LSI KL5KUSB101B chip, including the LinkSys USB10T, the
Entrega NET-USB-E45, the Peracom USB Ethernet Adapter, the 3Com
3c19250 and the ADS Technologies USB-10BT. This device is 10mbs
half-duplex only, so there's miibus or ifmedia support. This device
also requires firmware to be loaded into it, however KLSI allows
redistribution of the firmware images (I specifically asked about
this; they said it was ok).
Special thanks to Annelise Anderson for getting me in touch with
KLSI (eventually) and thanks to KLSI for providing the necessary
programming info.
Highlights:
- Add driver files to /sys/dev/usb
- update usbdevs and regenerate attendate files
- update usb_quirks.c
- Update HARDWARE.TXT and RELNOTES.TXT for i386 and alpha
- Update LINT, GENERIC and others for i386, alpha and pc98
- Add man page
- Add module
- Update sysinstall and userconfig.c
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
USB ethernet chip. Adapters that use this chip include the LinkSys
USB100TX. There are a few others, but I'm not certain of their
availability in the U.S. I used an ADMtek eval board for development.
Note that while the ADMtek chip is a 100Mbps device, you can't really
get 100Mbps speeds over USB. Regardless, this driver uses miibus to
allow speed and duplex mode selection as well as autonegotiation.
Building and kldloading the driver as a module is also supported.
Note that in order to make this driver work, I had to make what some
may consider an ugly hack to sys/dev/usb/usbdi.c. The usbd_transfer()
function will use tsleep() for synchronous transfers that don't complete
right away. This is a problem since there are times when we need to
do sync transfers from an interrupt context (i.e. when reading registers
from the MAC via the control endpoint), where tsleep() us a no-no.
My hack allows the driver to have the code poll for transfer completion
subject to the xfer->timeout timeout rather that calling tsleep().
This hack is controlled by a quirk entry and is only enabled for the
ADMtek device.
Now, I'm sure there are a few of you out there ready to jump on me
and suggest some other approach that doesn't involve a busy wait. The
only solution that might work is to handle the interrupts in a kernel
thread, where you may have something resembling a process context that
makes it okay to tsleep(). This is lovely, except we don't have any
mechanism like that now, and I'm not about to implement such a thing
myself since it's beyond the scope of driver development. (Translation:
I'll be damned if I know how to do it.) If FreeBSD ever aquires such
a mechanism, I'll be glad to revisit the driver to take advantage of
it. In the meantime, I settled for what I perceived to be the solution
that involved the least amount of code changes. In general, the hit
is pretty light.
Also note that my only USB test box has a UHCI controller: I haven't
I don't have a machine with an OHCI controller available.
Highlights:
- Updated usb_quirks.* to add UQ_NO_TSLEEP quirk for ADMtek part.
- Updated usbdevs and regenerated generated files
- Updated HARDWARE.TXT and RELNOTES.TXT files
- Updated sysinstall/device.c and userconfig.c
- Updated kernel configs -- device aue0 is commented out by default
- Updated /sys/conf/files
- Added new kld module directory
rev.1.168 should have been committed concurrently:
Fixed some style bugs (always use precisely 1 space after `:' in
dependency specifications).
Removed bogus dependency of ${FULLKERNEL} on ${BEFORE_DEPEND}.
Reminded by: peter
to `register_t *'. This fixes bugs like misplacement of argc and argv
on the user stack on i386's with 64-bit longs. We still use longs to
represent "words" like argc and argv, and assume that they are on the
stack (and that there is stack). The suword() and fuword() families
should also use register_t.
now. On one machine with <825a> and <875> controllers, `sym' correctly
attached. On another one with only a <ncr 53c810 fast10 scsi>, the `ncr'
driver correctly attached.
kernel builds so as not to confuse with perl4 when bootstrapping from old
systems. I don't know if this is still applicable but it shouldn't hurt
to be consistant at least.
Also copy vnode_if.sh to vnode_if.pl. Doing a 'sh vnode_if.sh' when it
was a perl script was kinda silly.
sys/modules Makefile after completing a buildworld.
History:
The bulk of this code was obtained from NetBSD approximately one year
ago (I have taken care to preserve the original NetBSD copyrights and
I thank the authors for their work.) At that time, the OSF/1 code was
what was left over from their initial bootstrapping off of OSF/1 and
did not provide support for executing shared binaries.
I have independently added support for shared libraries, and support
for some of the more obscure system calls. This code has been
available for testing and comment since January of 1999 and running on
production machines here at Duke since April.
Known working applications include:
- Netscape (all versions I've tried)
- Mathematica 3.0.2
- Splus 3.4
- ArcInfo 7.1
- Matlab (version unknown)
- SimOS
- Atom instrumented binaries (built on a real OSF/1 system)
Applications which are known not to work:
- All applications linking to libmach
- Adobe Acrobat (uses libmach)
This has been tested with applications running against shared
libraries from OSF/1 (aka Tru64) 4.0D and 4.0F.
Reviewed by: marcel, obrien
BDE-lint by: obrien
Agreed in principal to by: msmith
tsunami systems and the PCI bus-numbering system of FreeBSD. Eg, the former
allows for 2 PCI bus 2's (one each on hoses 0 and 1) while the latter
needs to give each PCI bus a unique monotonically increasing number.
It has been fairly well tested and correctly maps machines with a ppb on
hose 1 as well as machines with ppbs on both hoses.
DS10s remain untested, as I do not have a pci card with a ppb which will
pass POST in a tsunami.
This is a house of cards.
the kernel while the vnode_if.h header is a bunch of inlines to call the
code that is in the kernel. Generating the .h file on the fly is kinda
bogus because it has to match the one compiled into the kernel.
IMHO we should have kern/vnode_if.c and sys/vnode_if.h committed in the
tree but that's another battle.
by the Linux emulator (and other emulators) for syscall argument
translation. The x86 port currently seems to allow unrestricted kernel
accesses to user memory.
Reviewed by: alc, gallatin
background ]
Rename sys/pci/pci_ioctl.h to sys/sys/pciio.h to make it easier for
userland programs to use this interface. Reformat the file, and add a
BSD-style copyright to it.
Add a new man page for pci(4). The PCIOCGETCONF, PCIOCREAD, and PCIOCWRITE
ioctls are documented, but the PCIOCATTACHED ioctl is not documented
because it is not implemented.
Change includes of <pci/pci_ioctl.h> to <sys/pciio.h> or remove them
altogether. In many cases, pci_ioctl.h was unused.
Reviewed by: steve
which it replaces. The new driver supports all of the chips supported
by the ones it replaces, as well as many DEC/Intel 21143 10/100 cards.
This also completes my quest to convert things to miibus and add
Alpha support.
Other modules can register and unregister ioctl handlers to extend the
ioctls known by the Linuxulator. A recent application is the vmware
port. The Linuxulator itself uses the new interface to register its
handlers as well. Handlers for the following types of ioctls have been
defined:
cdrom
console (=keyboard and VT handling)
socket
sound
termio
All ioctl related defines and declarations have been moved to a new
file (linux_ioctl.h), except for the pluggable ioctl handler interface
definition.
While there, cleanup linux.h some more.
linux.h and linux_ioctl.[ch] have been made to conform to style(9) as
much as possible.
Inspired and reviewed by: Vladimir N. Silyaev
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
Angelini for allowing me to use his AS1000 to do the port.
Note that this is untested on AlphaServer 1000A hardware.
Reviewed by: dfr
Tested by: Cristian Angelini <chr.ang@biella.alpcom.it>
Obtained From: NetBSD
In combination with Doug's recent alpha_cpu.h, this reduces the cost
of ipl raising/lowering significantly. This is most pronounced when
doing file reads.
Reviewed by: dfr
specific instructions such as rpcc and mb. This should provide some
performance improvements and will allow me to delete the file pal.s.
To allow people time to update their loadable modules, I will leave pal.s
alone for now.
was likely to be counted as idle time.
Note that we are counting time spent in software interrupt handlers as
interrupt time, so this invalidates the i386 meaning of intr_nesting_level.
Reviewed by: dfr, bde
Tested by: anderson@cs.duke.edu
registering their interrupts with rman as though they were going through
the ISA pic. This prevents a conflict between isa & pci for irqs on such
machines.
Also hookup the chipset struct before calling platform.pci_intr_init().
This allows me to call inw/outw down in the platform code.
Add interrupt printfs to match the CIA chipset.
Reviewed by: dfr
Tested by: wilko
The old code was spread out through the machdep code and was sloppy about
enabling and disabling the FEN bit (which controls access to the FP
register set). This caused a DIAGNOSTIC warning "DANGER WILL ROBINSON:
FEN SET IN cpu_fork!" sometimes when operating under high loads and could
conceivably lead to processes getting incorrect FP results.
The new code is much more strict about the FEN bit and makes sure that
*only* fpcurproc ever has it enabled. This also allows us to remove a
section of code from the exception_return path which might improve
performance marginally.
Reviewed by: gallatin
* GC unused options
* Move options that exist on all architectures to conf/options
* Add missing options to LINT
* Sort undocumented options list in LINT
Reviewed by: green
data is copyin()'ed to a properly aligned buffer.)
Return EFAULT rather than EINVAL if the sigcontext is inaccessible,
as specified by the documentation.
Submitted by: bde
can deal with from 1GB to 2GB. I have no way to test with >1GB because I
don't have high enough density memory to get any one box over 1GB. However, I
have tested it on xp1000 & ds10 with < 1GB of memory & have verified that it
does no harm.
filesystem is discovered. Preference is given to using the kernel
environment variable vfs.root.mountfrom, which is set by the loader
according to the contents of /etc/fstab. Changes in the MD code
provide fallback mechanisms for systems not using the loader.
A more robust fallback path is also provided, with the last recourse
being to prompt on the console for a root device.
These changes drastically simplify the machine-dependant parts of
the root configuration process. In addition, support for CDROM root
devices has been removed; it was a nasty hack and didn't work.
only two conflicts, cdev #98 and cdev #99. These should be fixed.
MAKEDEV should probably be merged as well.
Static majors are (hopefully) going away one day soon.
This file is informational and not machine parsed by anything any more.
to config(8) for static device tables that have not existed for quite
some time. They have been aliases for 'device' for a while, and "tape"
went away entirely as it wasn't used anywhere (except in an example
in LINT.. "fixed").
If the ipl is lowered here, a machine can rapidly run out of stack
space when it is under heavy interrupt load. Without this fix,
my test machine would fall over within a few seconds when forwarding
14,000 packets/sec. With the patch, it has been up for over 24 hours
and has built the world at the same time.
submitted by: dfr@freebsd.org
eliminate an extra (useless) level of indirection in half of the page
queue accesses and (2) to use a single name for each queue throughout,
instead of, e.g., "vm_page_queue_active" in some places and
"vm_page_queues[PQ_ACTIVE]" in others.
Reviewed by: dillon
"rw" argument, rather than hijacking B_{READ|WRITE}.
Fix two bugs (physio & cam) resulting by the confusion caused by this.
Submitted by: Tor.Egge@fast.no
Reviewed by: alc, ken (partly)
Merge the contents (less some trivial bordering the silly comments)
of <vm/vm_prot.h> and <vm/vm_inherit.h> into <vm/vm.h>. This puts
the #defines for the vm_inherit_t and vm_prot_t types next to their
typedefs.
This paves the road for the commit to follow shortly: change
useracc() to use VM_PROT_{READ|WRITE} rather than B_{READ|WRITE}
as argument.
In order to make this work, I created a pseudo-PHY driver to deal with
Macronix chips that use the built-in NWAY support and symbol mode port.
This is actually all of them, with the exception of the original MX98713
which presents its NWAY support via the MII serial interface.
The mxphy driver actually manipulates the controller registers directly
rather than using the miibus_readreg()/miibus_writereg() bus interface
since there are no MII registers to read. The mx driver itself pretends
that the NWAY interface is a PHY locayed at MII address 31 for the sole
purpose of allowing the mxphy_probe() routine to know when it needs to
attach to a host controller.
* Change the hack used on the alpha for mapping devices into DENSE or
BWX memory spaces to a simpler one. Its still a hack and should be
a seperate api to explicitly map the resource.
* Add $FreeBSD$ as necessary.
Rather than teaching pci_ioctl about hoses, we just pass down a magic number
& let the platform code figure out what the hose is based on what the bus
number is.
concept approved by dfr
resource_list_release. This removes the dependancy on the
layout of ivars.
* Move set_resource, get_resource and delete_resource from
isa_if.m to bus_if.m.
* Simplify driver code by providing wrappers to those methods:
bus_set_resource(dev, type, rid, start, count);
bus_get_resource(dev, type, rid, startp, countp);
bus_get_resource_start(dev, type, rid);
bus_get_resource_count(dev, type, rid);
bus_delete_resource(dev, type, rid);
* Delete isa_get_rsrc and use bus_get_resource_start instead.
* Fix a stupid typo in isa_alloc_resource reported by Takahashi
Yoshihiro <nyan@FreeBSD.org>.
* Print a diagnostic message if we can't assign resources to a PnP
device.
* Change device_print_prettyname() so that it doesn't print
"(no driver assigned)-1" for anonymous devices.
can provide the correct context to each signal handler.
Fix broken sigsuspend(): don't use p_oldsigmask as a flag, use SAS_OLDMASK
as we did before the linuxthreads support merge (submitted by bde).
Move ps_sigstk from to p_sigacts to the main proc structure since signal
stack should not be shared among threads.
Move SAS_OLDMASK and SAS_ALTSTACK flags from sigacts::ps_flags to proc::p_flag.
Move PS_NOCLDSTOP and PS_NOCLDWAIT flags from proc::p_flag to procsig::ps_flag.
Reviewed by: marcel, jdp, bde
- Move intrhook stuff into kernel.h
- Remove all occurrences of #device <device.h>
- Add kernel.h were necessary (nowhere)
- delete device.h
This file contained the structures for cfdata (old style config) and is no
longer used. It was included by most drivers.
It confuses the remote debugger as the definition of 'struct device' in
device.h is found before the one in bus_private.h.
struct sigcontext and ucontext_t/mcontext_t are defined in such
a way that both (ie struct sigcontext and ucontext_t) can be
passed on to sigreturn. The signal handler is still given a
ucontext_t for maximum flexibility.
For backward compatibility sigreturn restores the state for the
alternate signal stack from sigcontext.sc_onstack and not from
ucontext_t.uc_stack. A good way to determine which value the
application has set and thus which value to use, is still open
for discussion.
NOTE: This change should only affect those binaries that use
sigcontext and/or ucontext_t. In the source tree itself
this is only doscmd. Recompilation is required for those
applications.
This commit also fixes a lot of style bugs without hopefully
adding new ones.
NOTE: struct sigaltstack.ss_size now has type size_t again. For
some reason I changed that into unsigned int.
Parts submitted by: bde
sigaltstack bug found by: bde
(behind the built-in ppb on hose 1) to be found:
When testing the adaptec controller on alpha, I realized I misread the xp1000
documentation and the way I'm calculating the bus number for PCI
config space accesses on the tsunami is wrong. I had thought that a bus
behind a ppb should be numbered as the nth bus in that hose, but it
actually needs to be the nth global bus within the system. The bus number
for the primary bus on a hose must always remain 0 when calculating config
space addresses.
a 2940UW. The dp264 (and ds20, I think) have an AIC7895 on board so it
is important the ahc driver be in GENERIC so that FreeBSD can install on
these boxes.
-----------------------------
The compatibility code and/or emulators have been updated:
iBCS2 now mostly uses the older syscalls. SVR4 now properly
handles all signals. This has been achieved by using the
new sigset_t throughout the emulator. The Linuxulator has
been severely updated. Internally the new Linux sigset_t is
made the default. These are then mapped to and from the
new FreeBSD sigset_t.
Also, rt_sigsuspend has been implemented in the Linuxulator.
Implementing this syscall basicly caused all this sigset_t
changing in the first place and the syscall has been used
throughout the change as a means for testing. It basicly is
too much work to undo the implementation so that it can
later be added again.
A special note on the use of sv_sigtbl and sv_sigsize in
struct sysentvec:
Every signal larger than sv_sigsize is not translated and is
passed on to the signal handler unmodified. Signals in the
range 1 upto and including sv_sigsize are translated.
The rationale is that only the system defined signals need to
be translated.
The emulators also have been updated so that the translation
tables are only indexed for valid (system defined) signals.
This change also fixes the translation bug already in the
SVR4 emulator.
-----------------------------
By introducing a new sigframe so that the signal handler operates
on the new siginfo_t and on ucontext_t instead of sigcontext, we
now need two version of sendsig and sigreturn.
A flag in struct proc determines whether the process expects an
old sigframe or a new sigframe. The signal trampoline handles
which sigreturn to call. It does this by testing for a magic
cookie in the frame.
The alpha uses osigreturn to implement longjmp. This means that
osigreturn is not only used for compatibility with existing
binaries. To handle the new sigset_t, setjmp saves it in
sc_reserved (see NOTE).
the struct sigframe has been moved from frame.h to sigframe.h
to handle the complex header dependencies that was caused by
the new sigframe.
NOTE: For the i386, the size of jmp_buf has been increased to hold
the new sigset_t. On the alpha this has been prevented by
using sc_reserved in sigcontext.
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
fields in struct cdevsw:
d_stop moved to struct tty.
d_reset already unused.
d_devtotty linkage now provided by dev_t->si_tty.
These fields will be removed from struct cdevsw together with
d_params and d_maxio Real Soon Now.
The changes in this patch consist of:
initialize dev->si_tty in *_open()
initialize tty->t_stop
remove devtotty functions
rename ttpoll to ttypoll
a few adjustments to these changes in the generic code
a bump of __FreeBSD_version
add a couple of FreeBSD tags
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
be set by a kernel conf option due to the struct buf structural
dependancy (sizing of b_pages[]) creating a conflict with modules
(which are not compiled with kernel config options overrides).
We'll be able to sysctl these two later on when the buffer subsystem
is revamped.
spaces which cross a segment boundry in the page table. pmap_kextract()
is not designed for access to the user space portion of the page
table and cannot handle the null-page-directory-entry case.
The fix is to have vm_fault_quick() return a success or failure which
is then used to avoid calling pmap_kextract().
requiring the user to figure it out. So, if you comment out all but the
machine type you are using, you automatically get the bus code just for
your system. (eg DEC_EB164 implies cia, etc). Multiple machine types
still pulls in the appropriate busses. This means, take things like
'controller cia0' out of your config.
Reviewed by: dfr (in principle)
random-seekable devices. This lets dd(1) know it can seek on them. It
also affects spec_vnopen() (IIRC), but only makes the path of execution smaller,
and does not change its behavior. This is when securelevel >= 2.
the Davicom DM9100 and DM9102 chipsets, including the Jaton Corporation
XPressNet. Datasheet is available from www.davicom8.com.
The DM910x chips are still more tulip clones. The API is reproduced
pretty faithfully, unfortunately the performance is pretty bad. The
transmitter seems to have a lot of problems DMAing multi-fragment
packets. The only way to make it work reliably is to coalesce transmitted
packets into a single contiguous buffer. The Linux driver (written by
Davicom) actually does something similar to this. I can't recomment this
NIC as anything more than a "connectivity solution."
This driver uses newbus and miibus and is supported on both i386
and alpha platforms.
SiS 900 and SiS 7016 PCI fast ethernet chipsets. Full manuals for the
SiS chips can be found at www.sis.com.tw.
This is a fairly simple chipset. The receiver uses a 128-bit multicast
hash table and single perfect entry for the station address. Transmit and
receive DMA and FIFO thresholds are easily tuneable. Documentation is
pretty decent and performance is not bad, even on my crufty 486. This
driver uses newbus and miibus and is supported on both the i386 and
alpha architectures.
the actual work. When USER_LDT is not defined for a kernel, sysarch returns
EOPNOTSUPP. Display a message in that case and return ENOSYS to userland.
Reviewed by: luoqi
new system is integrated with the ISA bus code more cleanly and allows
the future addition of more enumerators such as PnPBIOS and ACPI.
This commit also enables the new pcm driver since it is somewhat tied to
the new PnP code.
in the child. This corrects a problem where linux/alpha binaries see
the child's return value of fork as the parent's pid. This happens because
linux/alpha binaries apparently check the return value directly, rather
than looking for a non-zero value in a4, as *BSD & OSF/1 do.
Reviewed by:dfr@nlsystems.com
know if and when an unimplemented or obsoleted syscall is being used. Make the
message more end-user friendly.
And as long as we're here, rename some unimplemeted syscalls (linux_phys ->
linux_umount2, linux_vm86 -> linux_vm86old, linux_new_vm86 -> linux_vm86).
Change prototype for linux_newuname from `struct linux_newuname_t *' into
`struct linux_new_utsname *'. This change is reflected in linux.h and
linux_misc.c.
know if and when an unimplemented or obsoleted syscall is being used. Make the
message more end-user friendly.
And as long as we're here, rename some unimplemeted syscalls (linux_phys ->
linux_umount2, linux_vm86 -> linux_vm86old, linux_new_vm86 -> linux_vm86).
Change prototype for linux_newuname from `struct linux_newuname_t *' into
`struct linux_new_utsname *'. This change is reflected in linux.h and
linux_misc.c.
Lastly, make line-continuation and indentation more uniform.
PCI fast ethernet controller. Currently, the only card I know that uses
this chip is the D-Link DFE-550TX. (Don't ask me where to buy these: the
only cards I have are samples sent to me by D-Link.)
This driver is the first to make use of the miibus code once I'm sure
it all works together nicely, I'll start converting the other drivers.
The Sundance chip is a clone of the 3Com 3c90x Etherlink XL design
only with its own register layout. Support is provided for ifmedia,
hardware multicast filtering, bridging and promiscuous mode.
out of the asm code, and as a bonus implements rtprio and idprio for the
Alpha. Previously if you ran an idprio process, you were assured of a
deadlock.
The first reason for this rewrite is KNF conformance.
The second reason is to avoid redundancy. Each function printed the same
string, with only the syscall name being different. The actual printing is now
performed by a single function, which gets the syscall name as an argument.
The third reason is that of convenience. It's now very easy to add a new
dummy implementation. Just add ``DUMMY(foo);'' to the file. It's also a lot
easier now to see if a syscall has a dummy implementation or not.
The dummies are ordered on syscall number. Please maintain this when adding
new dummies (there're 32 candidates at the time of writing :-)
Reviewed by: bde
functions use the new sigset_t and sigaction_t which allows support for more
than 32 signals. Only the lower 32 signals are supported for now.
linux_rt_sigaction, linux_sigaction and linux_signal use linux_do_sigaction
to do the actual work. That way unnecessary redundancy is avoided. The same
has been done for linux_rt_sigprocmask and linux_sigprocmask. They call
linux_do_sigprocmask to do the actual work.
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
The linux syscalls translate the arguments first before invoking the
FreeBSD native syscalls.
PR: kern/9591
Originator: John Plevyak <jplevyak@inktomi.com>
a module. Also modified the code to work on FreeBSD/alpha and added
device vr0 to the alpha GENERIC config.
While I was in the neighborhood, I noticed that I was still using
#define NFPX 1 in all of the Makefiles that I'd copied from the fxp
module. I don't really use #define Nfoo X so it didn't matter, but
I decided to customize this correctly anyway.
we create the pty on the fly when it is first opened.
If you run out of ptys now, just MAKEDEV some more.
This also demonstrate the use of dev_t->si_tty_tty and dev_t->si_drv1
in a device driver.
space of PCI devices that don't exist cause PCI master & target aborts
rather than returning ~0 or giving a machine check. Bring in some code
from NetBSD to handle this properly.
obtained from: NetBSD
reviewed by: dfr
- device_print_child() either lets the BUS_PRINT_CHILD
method produce the entire device announcement message or
it prints "foo0: not found\n"
Alter sys/kern/subr_bus.c:bus_generic_print_child() to take on
the previous behavior of device_print_child() (printing the
"foo0: <FooDevice 1.1>" bit of the announce message.)
Provide bus_print_child_header() and bus_print_child_footer()
to actually print the output for bus_generic_print_child().
These functions should be used whenever possible (unless you can
just use bus_generic_print_child())
The BUS_PRINT_CHILD method now returns int instead of void.
Modify everything else that defines or uses a BUS_PRINT_CHILD
method to comply with the above changes.
- Devices are 'on' a bus, not 'at' it.
- If a custom BUS_PRINT_CHILD method does the same thing
as bus_generic_print_child(), use bus_generic_print_child()
- Use device_get_nameunit() instead of both
device_get_name() and device_get_unit()
- All BUS_PRINT_CHILD methods return the number of
characters output.
Reviewed by: dfr, peter
equivalent to SYS_RES_MEMORY for x86 but for alpha, the rman_get_virtual()
address of the resource is initialised to point into either dense-mapped
or bwx-mapped space respectively, allowing direct memory pointers to be
used to device memory.
Reviewed by: Andrew Gallatin <gallatin@cs.duke.edu>
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
When creating new processes (or performing exec), the new page
directory is initialized too early. The kernel might grow before
p_vmspace is initialized for the new process. Since pmap_growkernel
doesn't yet know about the new page directory, it isn't updated, and
subsequent use causes a failure.
The fix is (1) to clear p_vmspace early, to stop pmap_growkernel
from stomping on memory, and (2) to defer part of the initialization
of new page directories until p_vmspace is initialized.
PR: kern/12378
Submitted by: tegge
Reviewed by: dfr
large (1G) memory machine configurations. I was able to run 'dbench 32'
on a 32MB system without bring the machine to a grinding halt.
* buffer cache hash table now dynamically allocated. This will
have no effect on memory consumption for smaller systems and
will help scale the buffer cache for larger systems.
* minor enhancement to pmap_clearbit(). I noticed that
all the calls to it used constant arguments. Making
it an inline allows the constants to propogate to
deeper inlines and should produce better code.
* removal of inherent vfs_ioopt support through the emplacement
of appropriate #ifdef's, with John's permission. If we do not
find a use for it by the end of the year we will remove it entirely.
* removal of getnewbufloops* counters & sysctl's - no longer
necessary for debugging, getnewbuf() is now optimal.
* buffer hash table functions removed from sys/buf.h and localized
to vfs_bio.c
* VFS_BIO_NEED_DIRTYFLUSH flag and support code added
( bwillwrite() ), allowing processes to block when too many dirty
buffers are present in the system.
* removal of a softdep test in bdwrite() that is no longer necessary
now that bdwrite() no longer attempts to flush dirty buffers.
* slight optimization added to bqrelse() - there is no reason
to test for available buffer space on B_DELWRI buffers.
* addition of reverse-scanning code to vfs_bio_awrite().
vfs_bio_awrite() will attempt to locate clusterable areas
in both the forward and reverse direction relative to the
offset of the buffer passed to it. This will probably not
make much of a difference now, but I believe we will start
to rely on it heavily in the future if we decide to shift
some of the burden of the clustering closer to the actual
I/O initiation.
* Removal of the newbufcnt and lastnewbuf counters that Kirk
added. They do not fix any race conditions that haven't already
been fixed by the gbincore() test done after the only call
to getnewbuf(). getnewbuf() is a static, so there is no chance
of it being misused by other modules. ( Unless Kirk can think
of a specific thing that this code fixes. I went through it
very carefully and didn't see anything ).
* removal of VOP_ISLOCKED() check in flushbufqueues(). I do not
think this check is necessary, the buffer should flush properly
whether the vnode is locked or not. ( yes? ).
* removal of extra arguments passed to getnewbuf() that are not
necessary.
* missed cluster_wbuild() that had to be a cluster_wbuild_wb() in
vfs_cluster.c
* vn_write() now calls bwillwrite() *PRIOR* to locking the vnode,
which should greatly aid flushing operations in heavy load
situations - both the pageout and update daemons will be able
to operate more efficiently.
* removal of b_usecount. We may add it back in later but for now
it is useless. Prior implementations of the buffer cache never
had enough buffers for it to be useful, and current implementations
which make more buffers available might not benefit relative to
the amount of sophistication required to implement a b_usecount.
Straight LRU should work just as well, especially when most things
are VMIO backed. I expect that (even though John will not like
this assumption) directories will become VMIO backed some point soon.
Submitted by: Matthew Dillon <dillon@backplane.com>
Reviewed by: Kirk McKusick <mckusick@mckusick.com>
bit preliminary. It still returns an old-style code arg if SA_SIGINFO
is not set, but I'm not sure of the value of this since the traditional
bsd-style fourth argument (address) is missing.
Also, tidy up a bit of lint.
into uipc_mbuf.c. This reduces three sets of identical tunable code to
one set, and puts the initialisation with the mbuf code proper.
Make NMBUFs tunable as well.
Move the nmbclusters sysctl here as well.
Move the initialisation of maxsockets from param.c to uipc_socket2.c,
next to its corresponding sysctl.
Use the new tunable macros for the kern.vm.kmem.size tunable (this should have
been in a separate commit, whoops).
behavior slightly.
If machine/bus.h is included, but neither bus_memio.h nor bus_pio.h
are included, then behave as if both were included.
This won't change existing drivers, all of which include one or more
of bus_{p,mem}io.h, but will allow drivers from other systems to come
over with fewer changes. I freely admit that this might not be
optimal for some drivers, but those drivers can be optimized for
FreeBSD after the initial bringup happens.
Without the change, there is a bug that preclude drivers from
compiling with strange warning/errors.
I've been running this here for a while now w/o ill effects.
Reviewed by: gibbs
Not objected to by: bde, arch@ list.
On the VAX, it used to be used for special compilation to avoid the
optimizer which would mess with memory mapped devices etc. These days
we use 'volatile'.
loop it was supposed to be in. Correct some ugly formatting. Remember to
initialize the alignment tag. Honor and pass a callers request to contigalloc
if they had a non-zero alignment constraint.
SYSINIT_KT() etc (which is a static, compile-time procedure), use a
NetBSD-style kthread_create() interface. kproc_start is still available
as a SYSINIT() hook. This allowed simplification of chunks of the
sysinit code in the process. This kthread_create() is our old kproc_start
internals, with the SYSINIT_KT fork hooks grafted in and tweaked to work
the same as the NetBSD one.
One thing I'd like to do shortly is get rid of nfsiod as a user initiated
process. It makes sense for the nfs client code to create them on the
fly as needed up to a user settable limit. This means that nfsiod
doesn't need to be in /sbin and is always "available". This is a fair bit
easier to do outside of the SYSINIT_KT() framework.
i386 isa drivers that used to be order sensitive. The probe order of
those drivers is now determined by a list in isa_compat.c and config
file order is totally irrelevant.
run quite reliably now. I've explicitly tagged them as /* XXX overkill? */
although one does actually check for VM_PROT_EXECUTE.
Based on a suggestion by: Dmitrij Tejblum <tejblum@arc.hq.cti.ru>
Zap symbols.raw and glue to make symbols.* - it's not used on the ELF-only
alpha kernel. Symbol sorting is dead-end anyway once libkvm uses the
in-kernel linker symbol lookup.
lockmgr locks. This commit should be functionally equivalent to the old
semantics. That is, all buffer locking is done with LK_EXCLUSIVE
requests. Changes to take advantage of LK_SHARED and LK_RECURSIVE will
be done in future commits.
- Split syscons source code into manageable chunks and reorganize
some of complicated functions.
- Many static variables are moved to the softc structure.
- Added a new key function, PREV. When this key is pressed, the vty
immediately before the current vty will become foreground. Analogue
to PREV, which is usually assigned to the PrntScrn key.
PR: kern/10113
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
- Modified the kernel console input function sccngetc() so that it
handles function keys properly.
- Reorganized the screen update routine.
- VT switching code is reorganized. It now should be slightly more
robust than before.
- Added the DEVICE_RESUME function so that syscons no longer hooks the
APM resume event directly.
- New kernel configuration options: SC_NO_CUTPASTE, SC_NO_FONT_LOADING,
SC_NO_HISTORY and SC_NO_SYSMOUSE.
Various parts of syscons can be omitted so that the kernel size is
reduced.
SC_PIXEL_MODE
Made the VESA 800x600 mode an option, rather than a standard part of
syscons.
SC_DISABLE_DDBKEY
Disables the `debug' key combination.
SC_ALT_MOUSE_IMAGE
Inverse the character cell at the mouse cursor position in the text
console, rather than drawing an arrow on the screen.
Submitted by: Nick Hibma (n_hibma@FreeBSD.ORG)
SC_DFLT_FONT
makeoptions "SC_DFLT_FONT=_font_name_"
Include the named font as the default font of syscons. 16-line,
14-line and 8-line font data will be compiled in. This option replaces
the existing STD8X16FONT option, which loads 16-line font data only.
- The VGA driver is split into /sys/dev/fb/vga.c and /sys/isa/vga_isa.c.
- The video driver provides a set of ioctl commands to manipulate the
frame buffer.
- New kernel configuration option: VGA_WIDTH90
Enables 90 column modes: 90x25, 90x30, 90x43, 90x50, 90x60. These
modes are mot always supported by the video card.
PR: i386/7510
Submitted by: kbyanc@freedomnet.com and alexv@sui.gda.itesm.mx.
- The header file machine/console.h is reorganized; its contents is now
split into sys/fbio.h, sys/kbio.h (a new file) and sys/consio.h
(another new file). machine/console.h is still maintained for
compatibility reasons.
- Kernel console selection/installation routines are fixed and
slightly rebumped so that it should now be possible to switch between
the interanl kernel console (sc or vt) and a remote kernel console
(sio) again, as it was in 2.x, 3.0 and 3.1.
- Screen savers and splash screen decoders
Because of the header file reorganization described above, screen
savers and splash screen decoders are slightly modified. After this
update, /sys/modules/syscons/saver.h is no longer necessary and is
removed.
The cdevsw_add() function now finds the major number(s) in the
struct cdevsw passed to it. cdevsw_add_generic() is no longer
needed, cdevsw_add() does the same thing.
cdevsw_add() will print an message if the d_maj field looks bogus.
Remove nblkdev and nchrdev variables. Most places they were used
bogusly. Instead check a dev_t for validity by seeing if devsw()
or bdevsw() returns NULL.
Move bdevsw() and devsw() functions to kern/kern_conf.c
Bump __FreeBSD_version to 400006
This commit removes:
72 bogus makedev() calls
26 bogus SYSINIT functions
if_xe.c bogusly accessed cdevsw[], author/maintainer please fix.
I4b and vinum not changed. Patches emailed to authors. LINT
probably broken until they catch up.
Reformat and initialize correctly all "struct cdevsw".
Initialize the d_maj and d_bmaj fields.
The d_reset field was not removed, although it is never used.
I used a program to do most of this, so all the files now use the
same consistent format. Please keep it that way.
Vinum and i4b not modified, patches emailed to respective authors.
use ALPHA_PHYS_TO_K0SEG(offset) rather than just plain offet. I've verified
that this does not break other platforms (I've tested an AlphaStation 200
and a Personal Workstation 500au with this patch).
As to why this works, well.. Its black magic as far as I know. I obtained
this hack from Myricom, who in turn, obtained it from Compaq engineers.
Without this hack, XFree86 cannot talk to a PCI graphics card.
Reviewed by: Doug Rabson <dfr@nlsystems.com>
Obtained from: feldy@myri.com (Bob Felderman)
Compaq XP1000, AlphaServer DS20, AlphaServer DS10, and DP264
This has been tested *only* on XP1000's. I'll be interested to hear from
owners of other types of DEC_ST6600 alphas.
I'd like to thank Don Rice of Compaq for providing the documentation required
to support this platform on FreeBSD. I'd also like to thank Doug Rabson for newbus,
and for helping me get a multiple hoses working with newbus.
Reviewed by: Doug Rabson <dfr@nlsystems.com>
preparation for tsunami support. Previous chipsets' direct-mapped DMA
mask was always 1024*1024*1024. The Tsunami chipset needs it to be
2*1024*1024*1024
These changes should not affect the i386 port
Reviewed by: Doug Rabson <dfr@nlsystems.com>
|revision 1.13
|date: 1995/09/15 23:49:23; author: davidg; state: Exp; lines: +15 -2
|Check for page being resident when doing I/O with /dev/kmem and return
|EFAULT if it is not resident. This prevents the system from manufacturing
|a zero-fill page for unused but allocated areas of the kernel's VM.
* Re-work the resource allocation code to use helper functions in subr_bus.c.
* Add simple isa interface for manipulating the resource ranges which can be
allocated and remove the code from isa_write_ivar() which was previously
used for this purpose.
The specific intent of this commit is to pave the way for importing
Compaq XP1000 support. These changes should not affect the i386 port.
Reviewed by: Doug Rabson <dfr@nlsystems.com>
(actually, he walked me through most of it & deserves more than reviewd-by
credit )
instances to a parent bus.
* Define a new method BUS_ADD_CHILD which can be called from DEVICE_IDENTIFY
to add new instances.
* Add a generic implementation of DEVICE_PROBE which calls DEVICE_IDENTIFY
for each driver attached to the parent's devclass.
* Move the hint-based isa probe from the isa driver to a new isahint driver
which can be shared between i386 and alpha.
development that leads to lots of crashes during boot.
I have made a 'reinstall' target (like in ports, and reinstall.debug)
This is most useful if you want to keep /kernel.old as a known bootable
kernel. If you test a new kernel and have to reboot for a fix, a
'make reinstall' will install the new kernel over the top of the old
non-viable one, leaving the old one untouched. This is mainly meant
for development, not general users.
Made a new (inline) function devsw(dev_t dev) and substituted it.
Changed to the BDEV variant to this format as well: bdevsw(dev_t dev)
DEVFS will eventually benefit from this change too.
Virtualize bdevsw[] from cdevsw. bdevsw() is now an (inline)
function.
Join CDEV_MODULE and BDEV_MODULE to DEV_MODULE (please pay attention
to the order of the cmaj/bmaj arguments!)
Join CDEV_DRIVER_MODULE and BDEV_DRIVER_MODULE to DEV_DRIVER_MODULE
(ditto!)
(Next step will be to convert all bdev dev_t's to cdev dev_t's
before they get to do any damage^H^H^H^H^H^Hwork in the kernel.)
* Make the network code in the bootstrap more chatty (helps debugging)
* Add nfs root stuff to cpu_rootconf(). I also added a check to make sure
it really was netbooting which allows the use of the same kernel for local
and network boots.
* Tweak the de driver so that it takes the speed setting from the console
for the alpha (some PWSs have broken de chipsets). This is the same
behaviour as NetBSD/alpha.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu>
PV_TABLE_REF cleared before PV_TABLE_MOD, the page may get fault on read again.
On fault on write, pmap_emulate_reference mark the page dirty with
vm_page_dirty. That decrease ill effects of the bug.
The problem probably become more serious after my rev.1.18 a week ago.
- %fs register is added to trapframe and saved/restored upon kernel entry/exit.
- Per-cpu pages are no longer mapped at the same virtual address.
- Each cpu now has a separate gdt selector table. A new segment selector
is added to point to per-cpu pages, per-cpu global variables are now
accessed through this new selector (%fs). The selectors in gdt table are
rearranged for cache line optimization.
- fask_vfork is now on as default for both UP and SMP.
- Some aio code cleanup.
Reviewed by: Alan Cox <alc@cs.rice.edu>
John Dyson <dyson@iquest.net>
Julian Elischer <julian@whistel.com>
Bruce Evans <bde@zeta.org.au>
David Greenman <dg@root.com>
1:
s/suser/suser_xxx/
2:
Add new function: suser(struct proc *), prototyped in <sys/proc.h>.
3:
s/suser_xxx(\([a-zA-Z0-9_]*\)->p_ucred, \&\1->p_acflag)/suser(\1)/
The remaining suser_xxx() calls will be scrutinized and dealt with
later.
There may be some unneeded #include <sys/cred.h>, but they are left
as an exercise for Bruce.
More changes to the suser() API will come along with the "jail" code.
Interrupts under the new scheme are managed by the i386 nexus with the
awareness of the resource manager. There is further room for optimizing
the interfaces still. All the users of register_intr()/intr_create()
should be gone, with the exception of pcic and i386/isa/clock.c.
alpha/include/lock.h: remove nop simplelock macros, which are defined
in <sys/lock.h> if NCPUS == 1.
As a result, NULL_SIMPLELOCK is defined, and a few warnings removed.
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
Requested-by: ache
bde
dg
Modify targets for debug kernels: when -g was specified, make will
now build a debug kernel called kernel.debug, and create a stripped
version called kernel at the same time. The two targets install and
install.debug are otherwise unchanged.
Requested-by: dillon
Update man page accordingly.
2. Config complains if you use -g:
Debugging is enabled by default, there is no ned to specify the -g option
3. Config warns you if you don't use -s:
Building kernel with full debugging symbols. Do
"config -s BSD" for historic partial symbolic support.
To install the debugging kernel, do make install.debug
(BSD was the name of the config file I used; I print out the same
name).
4. Modify Makefile.i386, Makefile.alpha, Makefile.pc98 and config to
work if a kernel name other than 'kernel' is specified. This is
not absolutely necessary, but useful, and it was relatively easy.
I now have a kernel called /crapshit :-)
5. Modify Makefile.i386, Makefile.alpha, Makefile.pc98 "clean" target
to remove both the debug and normal kernel.
6. Modify all to install the stripped kernel by default and the debug
kernel if you enter "make install.debug".
7. Update version number of Makefiles and config.
unallocated parts of the last page when the file ended on a frag
but not a page boundary.
Delimitted by tags PRE_MATT_MMAP_EOF and POST_MATT_MMAP_EOF,
in files alpha/alpha/pmap.c i386/i386/pmap.c nfs/nfs_bio.c vm/pmap.h
vm/vm_page.c vm/vm_page.h vm/vnode_pager.c miscfs/specfs/spec_vnops.c
ufs/ufs/ufs_readwrite.c kern/vfs_bio.c
Submitted by: Matt Dillon <dillon@freebsd.org>
Reviewed by: Alan Cox <alc@freebsd.org>
the address of the ps_strings structure to the process via %ebx.
For other kinds of binaries, %ebx is still zeroed as before.
Submitted by: Thomas Stephens <tas@stephens.org>
Reviewed by: jdp
Like the PNIC, we have to copy packet headers in the receive handler
because the chip will only DMA to longword aligned buffers.
Also do some mindor cleanups.
the alpha. Now the ThunderLAN driver works on the alpha (both my
sample cards check out.) Update the alpha GENERIC config to include
ThunderLAN driver now that I've tested it.
sys/alpha/conf/GENERIC.
Note: the PNIC ignores the lower few bits of the RX buffer DMA address,
which means we have to add yet another kludge to make it happy. Since
we can't offset the packet data, we copy the first few bytes of the
received data into a separate mbuf with proper alignment. This puts
the IP header where it needs to be to prevent unaligned accesses.
Also modified the PNIC driver to use a non-interrupt driven TX
strategy. This improves performance somewhat on x86/SMP systems where
interrupt delivery doesn't seem to be as fast with an SMP kernel as
with a UP kernel.
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
to manage their own memory. Tested on my machine (make buildworld).
I've made analogous changes on the alpha, but don't have a machine
to test.
Not-objected-to by: dg, gibbs
already defined. This allows for cross building to work because we
need to lie to make to tell it to use the target names rather than the
host names.
This should have no effect on either architecture. I've confirmed
that the intel build by make buildworld's for the past 3 months.
not per-process. Keep it in `switchtime' consistently.
It is now clear that the timestamp is always valid in fork_trampoline()
except when the child is running on a previously idle cpu, which
can only happen if there are multiple cpus, so don't check or set
the timestamp in fork_trampoline except in the (i386) SMP case.
Just remove the alpha code for setting it unconditionally, since
there is no SMP case for alpha and the code had rotted.
Parts reviewed by: dfr, phk
to calculate a reasonable size for the swap partition).
* Fix a typo in remrq() where a process with idle priority would not be
correctly removed from the relavent queue. Note that realtime and idle
priorities are still not supported since the assembler code in
cpu_switch() does not check the realtime and idle queues.
is the preparation step for moving pmap storage out of vmspace proper.
Reviewed by: Alan Cox <alc@cs.rice.edu>
Matthew Dillion <dillon@apollo.backplane.com>
