more general VM system interfaces. So, their implementation can now
reside in kern_malloc.c alongside the other functions that are declared
in malloc.h.
about the various driver events like load, unload, reset, suspend,
restart, and ioctl operations.
Define driver's event rather than using hard-coded values. We don't
still send suspend/resume event to firmware.
Previously bge(4) used BGE_SDI_STATUS to send events. Because driver
has to access firmware mail box to inform current state, using
BGE_SDI_STATUS register was wrong. The end result was the same as
BGE_SDI_STATUS is 0x0C04.
No functional changes.
- add support for volumes above 2TiB with Promise metadata format;
- enforse and document other limitations:
- Intel and Promise metadata formats do not support disks above 2TiB;
- NVIDIA metadata format does not support volumes above 2TiB.
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
The origin of GENCOMM seems to come from Alteon Tigon Host/NIC
interface definition where it defines general communications region
which is active when firmware is loaded and running. This region
was used in communication between the host and processor internal
to the Tigon chip.
Broadcom data sheet also defines the region as 'Software Gencomm'
in NetXtreme memory map but lacks detailed description of its
interface so it was hard to know which ones are used for which
interface.
This change shall slightly enhance readability.
No functional changes.
larger than 4KB in size. However the maximum DMA segment size
created in DMA tag is 4KB, so we wouldn't encounter the issue here.
Just record this issue such that let developers not to create a DMA
segment that is larger than 4KB for BCM5719. It's possible to split
a DMA segment into multiple smaller ones in run time but I believe
it's not worth to implement that.
o Protect bge(4) status block access and register dump with driver lock.
o Add missing bus_dmamap_sync() before dumping status block.
o Use minimum status block size, 32 bytes, for status block dump on most
controllers except BCM5700 AX/BX.
While I'm here, make the handler show 5717 Plus in hardware flags.
* preserve AR_TxIntrReq on every descriptor in an aggregate chain,
not just the first descriptor;
* always blank out the descriptor in ar5416ChainTxDesc() when forming
aggregates - the way I'm using this in the 11n branch is to first
chain aggregates together, then use the other HAL calls to fill in
the details.
* Add the TID field in the TX status descriptor;
* Add in the 11n first/middle/last functions for fiddling
with the descriptors. These are from the Linux and the
reference driver, but I'm not (currently) using them.
* Add further AR_ISR_S5 register definitions.
Obtained from: Linux ath9k, Atheros
interfere with traffic, as the NF load can take quite a while and poking the
AGC every 10uS is just a bit silly.
Instead, just leave the baseband NF calibration where it is and just read it
back next time a longcal interval happens.
and constants related to the BIOS Enhanced Disk Drive Specification.
- Use this header instead of magic numbers and various duplicate structure
definitions for doing I/O.
- Use an actual structure for the request to fetch drive parameters in
drvsize() rather than a gross hack of a char array with some magic
size. While here, change drvsize() to only pass the 1.1 version of
the structure and not request device path information. If we want
device path information you have to set the length of the device
path information as an input (along with probably checking the actual
EDD version to see which size one should use as the device path
information is variable-length). This fixes data smashing problems
from passing an EDD 3 structure to BIOSes supporting EDD 4.
Reviewed by: avg
Tested by: Dennis Koegel dk neveragain.de
MFC after: 1 week
controller.
AX88772B data sheet does not show detailed information about
checksum offloading related things. It seems the controller has
lots of options to support checksum offloading but I failed to
understand why this feature requires so much complex controller
configuration and status bits.
One of major difference between AX88772B and its predecessor is
AX88772B uses a new RX header format when RX checksum offloading is
enabled. It also requires the received length of a frame should be
multiple of 4. Controller will pad necessary bytes to make the
length of received frame to be multiple of 4. It is driver's
responsibility to offset this pad bytes.
Note, AX88772B could be configured to get partial checksum value in
in RX header. This mode uses different RX header format and
currently we don't use that fature.
This change makes axe(4) use driver specific MII attach handler to
override uether(9)'s default MII attach and announce flow-control
capability for AX88178/AX88772A/AX88772B to PHY drivers. It seems
original AX88772 also supports flow-control but I didn't enable it
due to lack of test/access to the controller. The flow-control
threshold parameter is loaded from EEPROM and there is no way to
override this value without reprogramming EEPROM. For AX88772B,
TX/RX IP/TCP/UDP checksum offloading is announced to network stack.
IPv6 and PPPoE checksum offloading is also supported by controller
but we have no way to take advantage of these features.
Driver already knows PHY address so make PHY driver know that
information and remove unnecessary PHY address check used in
miibus_readreg/miibus_writereg callbacks. Also announce AX88178,
AX88772A and AX88772B support VLAN over-sized frame.
While I'm here clean up headers and remove axe_start() in
axe_init() because the link wouldn't be available right after media
change.
common cases that can be handled in constant time. The insight being
that a page's parent in the vm object's tree is very often its
predecessor or successor in the vm object's ordered memq.
Tested by: jhb
MFC after: 10 days
with older FreeBSD versions:
- Add -V option to 'geli init' to specify version number. If no -V is given
the most recent version is used.
- If -V is given don't allow to use features not supported by this version.
- Print version in 'geli list' output.
- Update manual page and add table describing which GELI version is
supported by which FreeBSD version, so one can use it when preparing GELI
device for older FreeBSD version.
Inspired by: Garrett Cooper <yanegomi@gmail.com>
MFC after: 3 days
of the CDDL licence explicitly requires every Contributor to add
a copyright notice.
This also reflects the copyright notices for the changes recently
added by Illumos.
MFC after: 3 days
interfaces. A host route has a NULL mask so check for that condition.
I have also been told by developers who customize the packet output
path with direct manipulation of the route entry (or the outgoing
interface to be specific). This patch checks for the route mask
explicitly to make sure custom code will not panic.
PR: kern/161805
MFC after: 3 days
masked out when adding a prefix route through the "route" command.
However, when deleting the route, simply changing the command keyword
from "add" to "delete" does not work. The failoure is observed in
both IPv4 and IPv6 route insertion. The patch makes the route command
behavior consistent between the "add" and the "delete" operation.
MFC after: 1 week
handler such that driver can announce interface capabilities and
can do its own MII attach. Currently all USB ethernet controllers
have no way to establish a link with pause capabilities. Lack of
checksum offloading support also was one of reason to bring this
change in.
This change adds a couple of wrappers to USB ethernet drivers
(uether_ifmedia_upd, uether_init and uether_start). All exported
functions in uether has prefix uether_ so I think it's more
consistent to have wrappers that follow the convention.
This change preserves ABI/KPI so it should be safe to merge this
change to stable/8.
While I'm here add missing __FBSDID and clean up headers.
Reviewed by: hselasky
