that piggybacks on bce_tick() callout.
- Instead of unconditionally resetting the controller, try to
skip the reset in case we got a pause frame, like em(4) did.
- Lock bce_tick() using callout_init_mtx().
Discussed with/Reviewed by: glebius, scottl, davidch
not needed if the proper ordering is done in attach and shutdown.
Remove usage of if_timer/watchdog and roll my own by piggybacking
off the tick() function.
Use the new usb system to allocate task queues instead of using
the system wide thread for taskqueues.
for usb. I hope that this will eventually be used for generic devices
that need full fledged blocking threads for event processing.
Create a taskqueue:
void usb_ether_task_init(device_t, int, struct usb_taskqueue *);
Enqueue a task:
void usb_ether_task_enqueue(struct usb_taskqueue *, struct task *);
Wait for all tasks queued to complete:
void usb_ether_task_drain(struct usb_taskqueue *, struct task *);
Destroy the taskqueue:
void usb_ether_task_destroy(struct usb_taskqueue *);
link state changes. Instead, build new speed/duplex/flow-control
settings from the values reported from PHY.
This should fix speed/duplex/flow-control mismatches between GMAC and
PHY which resulted in very poor Rx performance due to lots of
out-of-order packet delivery.
Reported by: Arno J. Klaassen <arno AT heho DOT snv DOT jussieu DOT fr>
Tested by: Arno J. Klaassen <arno AT heho DOT snv DOT jussieu DOT fr>
modern dual-core systems as well.
- Parse the _CST packages for each cpu and track all the states individually,
on a per-cpu basis.
- Revert to generic FADT/P_BLK based Cx control if the _CST package
is not present on all cpus. In that case, the new driver will
still support per-cpu Cx state handling. The driver will determine the
highest Cx level that can be supported by all the cpus and configure the
available Cx state based on that.
- Fixed the case where multiple cpus in the system share the same
registers for Cx state handling. To do that, added a new flag
parameter to the acpi_PkgGas and acpi_bus_alloc_gas functions that
enable the caller to add the RF_SHAREABLE flag. This flag could also be
useful to other callers (acpi_throttle?) in the tree but this change is
not yet made.
- For Core Duo cpus, both cores seems to be taken out of C3 state when
any one of the cores need to transition out. This broke the short sleep
detection logic. It is disabled now if there is more than one cpu in
the system for now as it fixed it in my case. This quirk may need to
be re-enabled later differently.
- Added support to control cx_lowest on a per-cpu basis. There is still
a generic cx_lowest to enable changing cx_lowest for all cpus with a single
sysctl and for ease of use. Sample output for the new sysctl:
dev.cpu.0.cx_supported: C1/1 C2/1 C3/57
dev.cpu.0.cx_lowest: C3
dev.cpu.0.cx_usage: 0.00% 43.16% 56.83%
dev.cpu.1.cx_supported: C1/1 C2/1 C3/57
dev.cpu.1.cx_lowest: C3
dev.cpu.1.cx_usage: 0.00% 45.65% 54.34%
hw.acpi.cpu.cx_lowest: C3
This work was done by Stephane E. Potvin with some simple reworking by
myself. Thank you.
Submitted by: Stephane E. Potvin <sepotvin / videotron.ca>
MFC after: 2 weeks
revision 1.98 is NOT merged, because FreeBSD does not support this
syntax.
revision 1.99 is NOT merged, "const poisoning" part is not applicable
to FreeBSD. There is no variable shadowing, GCC can't find
this one (but there are others)
revision 1.100 is NOT merged, because it was null patch (no changes)
revision 1.101 is NOT merged, there is no BIT() macro in FreeBSD
revision 1.102 is merged
revision 1.103 is partially merged. There is no ai.ifaceh in FreeBSD
revision 1.104 is NOT merged
revision 1.105 is merged
revision 1.106 is not merged, because of rev. 1.107
revision 1.107 is a backuout of 1.106
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
---snip---
New features:
1. Optional multichannel recording (32 channels on Live!, 64 channels
on Audigy).
All channels are 16bit/48000Hz/mono, format is fixed.
Half of them are copied from sound output, another half can be
used to record any data from DSP. What should be recorded is
hardcoded in DSP code. In this version it records dummy data, but
can be used to record all DSP inputs, for example..
Because there are no support of more-than-stereo sound streams
multichannell stream is presented as one 32(64)*48000 Hz 16bit mono
stream.
Channel map:
SB Live! (4.0/5.1)
offset (words) substream
0x00 Front L
0x01 Front R
0x02 Digital Front L
0x03 Digital Front R
0x04 Digital Center
0x05 Digital Sub
0x06 Headphones L
0x07 Headphones R
0x08 Rear L
0x09 Rear R
0x0A ADC (multi-rate recording) L
0x0B ADC (multi-rate recording) R
0x0C unused
0x0D unused
0x0E unused
0x0F unused
0x10 Analog Center (Live! 5.1) / dummy (Live! 4.0)
0x11 Analog Sub (Live! 5.1) / dummy (Live! 4.0)
0x12..-0x1F dummy
Audigy / Audigy 2 / Audigy 2 Value / Audigy 4
offset (words) substream
0x00 Digital Front L
0x01 Digital Front R
0x02 Digital Center
0x03 Digital Sub
0x04 Digital Side L (7.1 cards) / Headphones L (5.1 cards)
0x05 Digital Side R (7.1 cards) / Headphones R (5.1 cards)
0x06 Digital Rear L
0x07 Digital Rear R
0x08 Front L
0x09 Front R
0x0A Center
0x0B Sub
0x0C Side L
0x0D Side R
0x0E Rear L
0x0F Rear R
0x10 output to AC97 input L (muted)
0x11 output to AC97 input R (muted)
0x12 unused
0x13 unused
0x14 unused
0x15 unused
0x16 ADC (multi-rate recording) L
0x17 ADC (multi-rate recording) R
0x18 unused
0x19 unused
0x1A unused
0x1B unused
0x1C unused
0x1D unused
0x1E unused
0x1F unused
0x20..0x3F dummy
Fixes:
1. Do not assign negative values to variables used to index emu_cards
array. This array was never accessed when index is negative, but
Alexander (netchild@) told me that Coverity does not like it.
After this change emu_cards[0] should never be used to identify
valid sound card.
2. Fix off-by-one errors in interrupt manager. Add more checks there.
3. Fixes to sound buffering code now allows driver to use large playback
buffers.
4. Fix memory allocation bug when multichannel recording is not
enabled.
5. Fix interrupt timeout when recording with low bitrate (8kHz).
Hardware:
1. Add one more known Audigy ZS card to list. Add two cards with
PCI IDs betwen old known cards and new one.
Other changes:
1. Do not use ALL CAPS in messages.
Incomplete code:
1. Automute S/PDIF when S/PDIF signal is lost.
Tested on i386 only, gcc 3.4.6 & gcc41/gcc42 (syntax only).
---snip---
This commits enables a little bit of debugging output when the driver is
loaded as a module. I did a cross-build test for amd64.
The code has some style issues, this will be addressed later.
The multichannel recording part is some work in progress to allow playing
around with it until the generic sound code is better able to handle
multichannel streams.
This is supposed to fix
CID: 171187
Found by: Coverity Prevent
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
server.
Don't complain about a hard loop id of 0xffff- we get this in
point-to-point topologies with the 2300 and 2K Login firmware.
Up the timeout on register FC4 types commands.
- Rename confusing AGP_INTEL_I845_MCHCFG to AGP_INTEL_I845_AGPM.
- Move E7205 and E7505 from i8x5 to i8x0 family. It probably worked
because the actual offset is the same.
In fact, all three families have the bit at the exact same place. Only
differences are name and width of the registers, i.e., NBXCFG (0x50, dword),
RDCR (0x51, byte), AGPM (0x51, byte), MCHCFG (0x50, word) depending on
the family of the chipsets.
a spin mutex since it doesn't have an INTR_FAST interrupt handler.
Beyond that the driver is still under Giant anyway.
- Remove unneeded locking during attach across operations that can't be
called with locks held (such as bus_dma_tag_create()).
MFC after: 1 week
Not objected to by: scottl
start working with third party usb modules, where sometimes it
is not easy to set the inclusion order so that there are no multiple
inclusions, yet you want to compile with high WARNS levels).
I am not sure if there is a standard for having a leading and/or trailing _
in the macro name, the usb code seems to use both.
There are still several unprotected headers here so it might be useful
to do the same thing on other files as well as the need arises.
MFC After: 3 days
semantics.
- Stop testing bpf pointers for NULL. In some cases use
bpf_peers_present() and then call the function directly inside the
conditional block instead of the macro.
- For places where the entire conditional block is the macro, remove the
test and make the macro unconditional.
- Use BPF_MTAP() in if_pfsync on FreeBSD instead of an expanded version of
the old semantics.
Reviewed by: csjp (older version)
o change handling of regdomain-related mib knobs so they can be set
post-attach: regdomain, countrycode, outdoor, and xchanmode; the
hal will not permit changing the regdomain but we expose it for now
o on regdomain/countrycode change recalculate the channel list and
push it to the net80211 layer (NB: looks to need more tweaking)
o setup rate tables for half/quarter rate channels
o honor half/quarter rate channel configs when changing channels
o honor half/quarter rate channel configs when setting the slot time
o use hack/nonstandard channel numbering scheme for the public safety
band to avoid overlapping 2.4G channels on dual-band cards
o remove setup of ic_sup_rates; the net80211 layer can do this for us
and it simplifies handling of half/quarter rate channels
Tested only in Public Safety Band with cards that have RF5112.
bge_intr(). Some of them are used in bge_poll(). Simplify by only
initializing these for polling mode and not toggling them when switching
modes. This also fixes missing synchronization with the coalescing
engine in the toggling.
The problem was that I was acquiring the driver sx lock and then waiting
for a taskqueue to drain, however the taskqueue itself would try to
acquire the lock as well leading to a deadlock.
To fix the problem roll my own exclusive lock that allows for lock
cancellation. This is a normal exclusive lock, however if someone
marks it as "dead" then all waiters who request an error return will
get back an error instead of continuing to wait for the lock.
In this particular case, the shutdown and detach functions kill the
lock while the async task thread tries to acquire the lock but will
abort if the lock returns an error.
The other option was to drop the driver lock mid-detach and mid-shutdown,
mid-detach was a ok, however mid-shutdown was not.
While I'm here, fix a bug in what appears to be the mii link status
word in the softc going out to lunch. Explicitly set the status
word to 1 after initializing the mii. This would result in an interface
that would never respond to "if_start" requests as the mii interface
would always look down.
return an error since it returns a count of battery devices in the system.
Set it to 0 explicitly, since it is the only switch branch that doesn't set
it.
# I guess no one uses it.
would be able to work with aac(4).
This approach is used by some other drivers as well. However, we
need a more generic way to do this in order to avoid having to
special case headers in individual drivers for each platform.
Obtained from: Adaptec (version b11518)
Approved by: scottl
been handled instead of when at least one descriptor was just handled.
For bge, it is normal to get a txeof when only a small fraction of the
queued tx descriptors have been handled, so the bug broke the watchdog
in a usual case.
- moved the synchronizing bus read to after the bus write for the first
interrupt ack so that it actually synchronizes everything necessary.
We were acking not only the status update that triggered the interrupt
together with any status updates that occurred before we got around
to the bus write for the ack, but also any status updates that occur
after we do the bus write but before the write reaches the device.
The corresponding race for the second interrupt ack resulted in
sometimes returning from the interrupt handler with acked but
unserviced interrupt events. Such events then remain unserviced
until further events cause another interrupt or the watchdog times
out.
The race was often lost on my 5705, apparently since my 5705 has broken
event coalescing which causes a status update for almost every packet,
so another status update is quite likely to occur while the interrupt
handler is running. Watchdog timeouts weren't very noticeable,
apparently because bge_txeof() has one of the usual bugs resetting the
watchdog.
- don't disable device interrupts while bge_intr() is running. Doing this
just had the side effects of:
- entering a device mode in which different coalescing parameters apply.
Different coalescing parameters can be used to either inhibit or
enhance the chance of getting another status update while in the
interrupt handler. This feature is useless with the current
organization of the interrupt handler but might be useful with a
taskqueue handler.
- giving a race for ack+reenable/return. This cannot be handled
by simply rearranging the order of bus accesses like the race for
ack+keepenable/entry. It is necessary to sync the ack and then
check for new events.
- taking longer, especially with the extra code to avoid the race on
ack+reenable/return.
Reviewed by: ru, gleb, scottl
re_watchdog() in order to avoid races accessing if_timer.
- Use bus_get_dma_tag() so re(4) works on platforms requiring it.
- Remove invalid BUS_DMA_ALLOCNOW when creating the parent DMA tag
and the tags that are used for static memory allocations.
- Don't bother to set if_mtu to ETHERMTU, ether_ifattach() does that.
- Remove an unused variable in re_intr().
watchdog timer in dc_txeof() in case there are still unhandled
descriptors as dc_poll() invokes dc_poll() unconditionally.
Otherwise this would result in the watchdog timer constantly being
being reloaded and thus circumvent that the watchdog ever fires in
the DEVICE_POLLING case.
Pointed out by: bde
- Do not repeatedly read vendor/device IDs while probing.
- Remove redundant bzero(3) for softc. device_get_softc(9) does it for free[1].
Reviewed by: glebius
Suggested by: glebius[1]
- If we want mii_phy_add_media() to add 1000baseT media, we need to
supply sc->mii_extcapabilities.
- Fix formatting when announcing autonegotiation support.
behave as expected.
Also:
- Return an error if WD_PASSIVE is passed in to the ioctl as only
WD_ACTIVE is implemented at the moment. See sys/watchdog.h for an
explanation of the difference between WD_ACTIVE and WD_PASSIVE.
- Remove the I_HAVE_TOTALLY_LOST_MY_SENSE_OF_HUMOR define. If you've
lost your sense of humor, than don't add a define.
Specific changes:
i80321_wdog.c
Don't roll your own passive watchdog tickle as this would defeat the
purpose of an active (userland) watchdog tickle.
ichwd.c / ipmi.c:
WD_ACTIVE means active patting of the watchdog by a userland process,
not whether the watchdog is active. See sys/watchdog.h.
kern_clock.c:
(software watchdog) Remove a check for WD_ACTIVE as this does not make
sense here. This reverts r1.181.
work:
- A new PCI quirk (PCI_QUIRK_DISABLE_MSI) is added to the quirk table.
- A new pci_msi_device_blacklisted() determines if a passed in device
matches an MSI quirk in the quirk table. This can be overridden (all
quirks ignored) by setting the hw.pci.honor_msi_blacklist to 0.
- A global blacklist check is performed in the MI PCI bus code by checking
to see if the device at 0:0:0 is blacklisted.
Tested by: jdp
1) s/mi/mfi/ in FreeBSD ioctl path
2) add in "\n" on various failure messages
3) cap the length of time to abort an AEN command
4) fix passing sense data back to user to make Dell's Linux firmware
upgrade tool happy.
5) bump the MFI_POLL_TIMEOUT_SECS from 10s to 50s since the
firmware flash command can take ~40s to return.
This is some clean-up and enables RAID firmware to updated via Dell's
tool. Note Dell's tool requires the updates to the Linux emulator
that has been done in -current with TLS etc.
I need to discuss with scottl how to better submit mfi commands to
the firmware via the ioctl path so we don't do it in polled mode.
by vnode. Allow for md thread and the thread that owns lock on vnode
backing the md device to do the write even when runningbufspace is
exhausted.
Tested by: Peter Holm
Reviewed by: tegge
MFC after: 2 weeks
have been added erroneously, and it causes problems on some chips. A larger
change is needed to do this write at a more appropriate place, but that
change requires reworking the ASF logic. That will be worked on in the
future.
Submitted by: Bruce Evans
o no more ds_vdata in tx/rx descriptors
o split h/w tx/rx descriptor from s/w status
o as part of the descriptor split change the rate control module api
so the ath_buf is passed in to the module so it can fetch both
descriptor and status information as needed
o add some const poisoning
Also for sample rate control algorithm:
o split debug msgs (node, rate, any)
o uniformly bounds check rate indices (and in some cases correct checks)
o move array index ops to after bounds checking
o use final tsi from the status block instead of the h/w descriptor
o replace h/w descriptor struct's with proper mask+shift defs (this
doesn't belong here; everything is known by the driver and should
just be sent down so there's no h/w-specific knowledge)
MFC after: 1 month
controller. Due to lack of documentation, this driver is based on the
code from sk(4) and Marvell's myk(4) driver for FreeBSD. I've also
adopted the OpenBSD interface name, msk(4) in order to reduce naming
differences between BSDs.
The msk(4) driver supports the following Gigabit Ethernet adapters.
o SysKonnect SK-9Sxx Gigabit Ethernet
o SysKonnect SK-9Exx Gigabit Ethernet
o Marvell Yukon 88E8021CU Gigabit Ethernet
o Marvell Yukon 88E8021 SX/LX Gigabit Ethernet
o Marvell Yukon 88E8022CU Gigabit Ethernet
o Marvell Yukon 88E8022 SX/LX Gigabit Ethernet
o Marvell Yukon 88E8061CU Gigabit Ethernet
o Marvell Yukon 88E8061 SX/LX Gigabit Ethernet
o Marvell Yukon 88E8062CU Gigabit Ethernet
o Marvell Yukon 88E8062 SX/LX Gigabit Ethernet
o Marvell Yukon 88E8035 Gigabit Ethernet
o Marvell Yukon 88E8036 Gigabit Ethernet
o Marvell Yukon 88E8038 Gigabit Ethernet
o Marvell Yukon 88E8050 Gigabit Ethernet
o Marvell Yukon 88E8052 Gigabit Ethernet
o Marvell Yukon 88E8053 Gigabit Ethernet
o Marvell Yukon 88E8055 Gigabit Ethernet
o Marvell Yukon 88E8056 Gigabit Ethernet
o D-Link 550SX Gigabit Ethernet
o D-Link 560T Gigabit Ethernet
Unlike OpenBSD/NetBSD msk(4), the msk(4) driver supports all hardware
features including TCP/UDP checksum offload for transmit, MSI, TCP
segmentation offload(TSO), hardware VLAN tag stripping/insertion,
and jumbo frames(up to 9022 bytes). The only unsupported hardware
feature except RLMT is Rx checksum offload which I don't know how to
make it work reliably.
Known Issues:
It seems msk(4) does not work on the second port of dual port NIC.
(The first port works without problems.)
Thanks to Marvell for releasing the BSD licensed myk(4) driver and
thanks to all users helped fixing bugs.
Tested by: bz, philip, bms,
YAMAMOTO Shigeru < shigeru AT iij DOT ad DOT jp >,
Dmitry Pryanishnikov < dmitry AT atlantis DOT dp DOT ua >,
Jia-Shiun Li < jiashiun AT gmail DOT com >,
David Duchscher < daved AT tamu DOT edu >,
Arno J. Klaassen < arno AT heho DOT snv DOT jussieu DOT fr>,
Nicolae Namolovan < adrenalinup AT gmail DOT com>,
Andre Guibert de Bruet < andy AT siliconlandmark DOT com >
current ML
Tested on: i386, amd64
subtypes of HT capabilities.
- Add constants for the MSI mapping window HT PCI capability.
- On i386 and amd64, enable the MSI mapping window on any HT bridges we
encounter and report any non-standard mapping window addresses.
pcib_alloc_msix() methods instead of using the method from the generic
PCI-PCI bridge driver as the PCI-PCI methods will be gaining some PCI-PCI
specific logic soon.
- Use the appropriate register writing method when reseting the chip
- Program the descriptor DMA engine correctly.
- More reliably detect certain chips and their features.
Also add some low-level debugging tools to help future work on this driver.
Submitted by: David Christenson (proof of concept changes)
Sponsored by: www.UIA.net
- Correct RX packet drop counter for BCM5705+. This register is read/clear
and it wraps very quickly under heavy packet drops because only the lower
ten bits are valid according to the documentation. However, it seems few
more bits are actually valid and the rest bits are always zeros[1].
Therefore, we don't mask them off here. To get accurate packet drop count,
we need to check the register from bge_rxeof(). It is commented out for now,
not to penalize normal operation. Actual performance impact should be
measured later.
- Correct integer casting from u_long to uint32_t. Casting is not really
needed for all supported platforms but we better do this correctly[2].
Tested by: bde[1]
Suggested by: bde[2]
o Remove unused static global variable e1000phy_debug.
o Take advantage of mii_phy_dev_probe().
o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5.
o Add IFM_NONE as e1000phy(4) supports it without issues.
o Nuke magic PHY programming sequence in PHY reset and follow correct
reset sequence. [1]
o Make manual media selection work for all supported media types.
o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in
configurations with multiple PHYs.
o In 1000baseT, when setting the link manually, one side must be the
master and the other the slave. If LINK0 is set, program the PHY
to be a master, otherwise it's a slave.
o When we lost a link, reset mii_ticks immediately so it correctly
check number of seconds elapsed in autonegotiation phase.
o Announce link loss right after it happens.
o After kicking autonegotiation, report PHY status instead of
returning immediatly.
o When link state check is in progress, check auto negotiation
completion bit only when auto negotiation is enbaled.
o When PHY is resolved to a master, show it with IFM_FLAG2.
Special thanks to marius who fixed several nits in original patch.
In half-duplex mode, nfe(4) fails to send packets. I think it's a bug
in nfe(4) as the same PHY works without problems on msk(4).
Obtained from: em(4) [1]
Reviewed by: marius
Tested by: bz
Either they're there early and the ispfw sets have
registered themselves, or they're not.
The module dependency stuff isn't quite what we want
anyway. If the user doesn't want the load placed on
system memory by loading the firmware, they don't
specify it to be loaded (either by being linked in
or via being a module to be loaded and then hooked
in with firmware(9)). It doesn't then make sense to
then override what they want by pulling it in anyway.
This might be able to work if we were able to pull in
just exactly what we needed for the card we have- but
that's an optimization left for the future.
hme_watchdog() in order to avoid races accessing if_timer.
- Use bus_get_dma_tag() so hme(4) works on platforms requiring it.
- Don't bother to set if_mtu to ETHERMTU, ether_ifattach() does that.
gem_watchdog() in order to avoid races accessing if_timer.
While at it relax the watchdog a bit by reloading it in gem_tint()
if there are still packets enqueued.
- Don't bother to set if_mtu to ETHERMTU, ether_ifattach() does that.
- Fix inconsistencies in prototypes.
depending on the NIC and isn't used at all with HomePNA links)
instead of if_slowtimo() for driving dc_watchdog() in order to
avoid races accessing if_timer.
- Use bus_get_dma_tag() so dc(4) works on platforms requiring it.
- Don't bother to set if_mtu to ETHERMTU, ether_ifattach() does that.
- Remove an alpha remnant in dc_softc.
of the nvenet lib upgrade (the constant went from 63 (2^n - 1) to
32 (2^n)). For reasons that are not obvious to me this fixes the driver
on at least some NICs.
MFC after: 3 days
with- not hope for the best. Change some things which were gated
off of 24XX to be gated off of 2K login support. Convert some
isp_prt calls to xpt_print calls.
Add a note that suggests a cleanup.
Note: This patch was derived based on looking at the pvrxxx/pvr250
ports' Makefiles only, and may be incomplete. It is not derived from
anything I saw from Hauppage.
- In hme_eint() print MIF register contents on MIF interrupts.
- In hme_mifinit() don't bother to preserve the previous MIF config.
This was mainly done in order to preserve the PHY select bit (external
or internal PHY) but which only needs to be set as appropriate when
reading from or writing to the desired PHY in hme_mii_{read,write}reg().
Similarly don't bother to set the PHY select bit in hme_mii_statchg().
- In hme_mii_{read,write}reg() ignore requests to PHYs other than the
external and internal PHY one.
- Move enabling/disabling the MII drivers of the external transceiver
from hme_init_locked() and based on the sheer presence of an external
to hme_mifinit() and based on the currently selected media, defaulting
to the internal transceiver when the media hasn't been set, yet.
Invoke hme_mifinit() from the newly added hme_mediachange_locked() so
the setting of the MII drivers is updated when changing media.
These changes keep the MII bus from wedging (which manifests in the HME
and the PHYs no longer being able to communicate with each other) when
the PHY device drivers isolate the unused PHY in two-PHY configurations
as present in f.e. Netra t1 100 while changing media, either from
hme_init_locked() (see also below) or via ifconfig(8). They also allow
for using both transceivers/PHYs.
- In the newly added hme_mediachange_locked() also reset the PHYs in two-
PHY configurations before invoking mii_mediachg(). This is required
for successfully unisolating the previously unused PHY when switching
between PHYs.
- Now that changing media should no longer cause problems back out rev.
1.27 and re-enable setting the current media in hme_init_locked() (see
the commit message of rev. 1.23 for more info).
These changes are roughly a merge of NetBSD gem.c rev. 1.32 - 1.35 (1.30
was already fixed differently in our 1.36; 1.31 and 1.32 were wrong) with
some parts reworked and things that don't make sense like setting the MII
drivers and restoring the previous MIF and XIF settings in hme_mii_{read,
write}reg() omitted.
MFC after: 2 weeks
read wasn't flagging the SYNC mode was enabled. The temp
values for offset and sync period were uint8_t, but were
being assigned and shifted from a uint32_t value.
This didn't show up in testing because a random number
of 1030 cards set a bit that says "honor BIOS negotiation",
which means this whole code path was skipped.
This should clear up at least some of the negotation
issues that have been seen.
Fix things to use the LSI-Logic Fusion Library mask and shift names for
offset and sync, no matter how awkward they are, in preference to just
plain numbers.
- Don't set MIIF_NOISOLATE so amphy(4) can be used in configurations
with multiple PHYs. There doesn't seem to be a problem with isolating
AM79c873 and workalikes per se nor in combination with the NICs they're
used with and amphy(4) was already adding IFM_NONE anyway.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
- Fix a whitespace nit.
Obtained from: NetBSD dmphy(4) (except for the last item)
MFC after: 2 weeks
the currently selected media is of type IFM_AUTO as auto-negotiation
doesn't need to be kicked anyway.
- Fix a whitespace nit.
- Probe another Altima PHY, which is a AC101 workalike and integrated
in at least ADMtek ADM8511 but apparently is not mentioned in any
publically available data sheet so the actual identifier is unknown.
- Don't set MIIF_NOISOLATE so acphy(4) can be used in configurations
with multiple PHYs. There doesn't seem to be a problem with isolating
AC101 and workalikes per se nor in combination with the NICs they're
used with.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
Obtained from: NetBSD (except for the first and second item)
MFC after: 2 weeks
in at least ADMtek ADM8511 but apparently is not mentioned in any
publically available data sheet so the actual identifier is unknown.
- Add Davicom DM9102 PHY.
- Add DM9101 to the description of AMD 79C873 as at least some Davicom
DM9101F identify identical to AMD 79C873.
Obtained from: NetBSD
MFC after: 2 weeks
with multiple PHYs. There doesn't seem to be a problem with isolating
78Q2120 per se nor in combination with the NICs they're used with and
tdkphy(4) was already adding IFM_NONE anyway.
- Set MIIF_NOLOOP as loopback doesn't work with this PHY. The MIIF_NOLOOP
flag currently triggers nothing but hopefully will be respected by
mii_phy_setmedia() later on.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
Thanks to Hans-Joerg Sirtl for lending me test hardware.
Obtained from: NetBSD tqphy(4)
MFC after: 2 weeks
with multiple PHYs and un-comment case IFM_NONE in case MII_MEDIACHG
rgephy_service(). There doesn't seem to be a problem with isolating
RTL8169S and their internal PHY.
- Take advantage of mii_phy_add_media(). [1]
Obtained from: NetBSD [1]
Tested by: yongari
MFC after: 2 weeks
- Fix some whitespace nits.
- Fix some spelling in comments.
- Use MII_ANEGTICKS instead of 5.
- Don't define variables in nested scope.
- Remove superfluous returns at the end of void functions.
- Remove unused static global rgephy_mii_model.
- Remove dupe $Id$ in tdkphy(4).
- Sort brgphys table.
MFC after: 2 weeks
- Playback and headphone/speaker automute works.
- Recording untested due to me being deaf doing back-and-forth
remote debugging.
Free Macbook donation is highly appreciated :)
Tested by: Dennis Pielken <mips128@gmx.net>
mii_phy_match() API and takes care of the PHY device probe based on
the struct mii_phydesc array and the match return value provided.
Convert PHY drivers to take advantage of mii_phy_dev_probe(),
converting drivers to provide a mii_phydesc table in the first
place where necessary.
Reviewed by: yongari
MFC after: 2 weeks
discarded RX packets to input error for BCM5705 or newer chipset as the others.
Unfortunately we cannot do the same for output errors because ifOutDiscards
equivalent register does not exist. While I am here, replace misleading and
wrong BGE_RX_STATS/BGE_TX_STATS with BGE_MAC_STATS. They were reversed but
worked accidently.
machines and both TX and RX were broken on big-endian machines.
The chip design is crazy -- on RX, it puts the 16-bit VLAN tag
in network byte order (big-endian) in the 32-bit little-endian
register!
Thanks to John Baldwin for helping me document this change! ;-)
Tested by: sat (amd64), test program (sparc64)
PR: kern/105054
MFC after: 3 days
aue_tick calls several synchronous usb functions from a timeout(9),
this is very broken since a timeout(9) is run as an interrupt
and the usb functions tsleep.
A stopgap fix is to schedule a taskqueue task from the timeout
and defer work to that taskqueue task.
Preliminary support for Atmel AT45D series of DataFlash on the
SPI bus (ok, not really a hardware bus, but a logical
connection). This works only for the 8MB version of the part
due to hard coding. Both read and write are supported.
the currently selected media is of type IFM_AUTO as auto-negotiation
doesn't need to be kicked anyway.
- In rlphy_status() just use if_dname instead of determining the name
of the parent NIC via device_get_name(device_get_parent(sc->mii_dev)).
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
- Fix some whitespace nits and remove commented out code that just can't
be used with RealTek PHYs.
MFC after: 2 weeks
the currently selected media is of type IFM_AUTO as auto-negotiation
doesn't need to be kicked anyway.
- Don't set MIIF_NOISOLATE so qsphy(4) can be used in configurations
with multiple PHYs. There doesn't seem to be a problem with isolating
QS6612 per se nor in combination with the NICs they're used with.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
Obtained from: NetBSD (except for the first item)
MFC after: 2 weeks
loopback to work PCnet chips additionally need to be placed into
external loopback mode which pcn(4) doesn't do so far.
- In nsphy_service() just use if_dname instead of determining the name
of the parent NIC via device_get_name(device_get_parent(sc->mii_dev)).
- Don't set MIIF_NOISOLATE, except for when used in combination with a
NIC that wedges when isolating the PHYs, so nsphy(4) can be used in
configurations with multiple PHYs.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia() (requires the MIIF_FORCEANEG
added in sys/dev/mii/mii_physubr.c 1.26, sys/dev/mii/miivar.h 1.19).
- Implement a separate nsphy_reset(). There are two reasons for this:
1) This PHY can take an inordinate amount of time to reset if media
is attached; under fairly normal circumstances up to nearly one
second. This is because it appears to go through an implicit auto-
negotiation cycle as part of the reset.
2) During reset and auto-negotiation, the BMCR will clear the reset
bit before the process is complete. It will return 0 until the
process is complete and it's safe to access the PHY again.
This is the first of two changes required to make the combination of
Am79c971 and DP83840A found on certain HP cards and on-board in IBM
machines work.
- Fix some whitespace nits.
Based on: NetBSD (except for the first and second item)
MFC after: 2 weeks
with multiple PHYs. There doesn't seem to be a problem with isolating
LXT970 per se nor in combination with the NICs they're used with and
lxtphy(4) was already adding IFM_NONE anyway.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
- Take advantage of mii_phy_setmedia().
- Fix some whitespace nits.
Obtained from: NetBSD
MFC after: 2 weeks
the BMSR contains any media at all to mii_phy_add_media(). The majority
of the drivers currently using mii_phy_add_media() were missing such a
check anyway though.
MFC after: 2 weeks
take place if IFM_AUTO is selected. This allows drivers like nsphy(4),
which need to force writing the ANAR according to the BMSR, to take
advantage of mii_phy_setmedia(). [1]
- In mii_phy_reset() once the current media is set don't isolate the PHY
corresponding to the instance of the currently selected media rather
than unconditionally not isolating the PHY corresponding to instance 0.
This saves a isolation-unisolation-cycle of the PHY corresponding to
the currently selected media for the case were it isn't instance 0.
- Fix some whitespace nits. [1]
Obtained from: NetBSD [1]
MFC after: 2 weeks
an URQ_REQUEST when DMA segments are passed to usbd_start_transfer();
when the request doesn't include the optional data buffer the size of
the transfer (xfer->length) is 0, in which case usbd_transfer() won't
create a DMA map but call usbd_start_transfer() with no DMA segments.
With the previous change this could result in the bus_dmamap_sync()
implementation dereferencing the NULL-pointer passed as the DMA map
argument.
While at it fix what appears to be a typo in usbd_start_transfer();
in order to determine wheter usbd_start_transfer() was called with
DMA segments check whether the number of segments is > 0 rather than
the pointer to them being > 0.
OK'ed by: imp
in every sense.
General
-------
- Multichannel safe, endian safe, format safe
* Large part of critical pcm filters such as vchan.c, feeder_rate.c,
feeder_volume.c, feeder_fmt.c and feeder.c has been rewritten so that
using them does not cause the pcm data to be converted to 16bit little
endian.
* Macrosses for accessing pcm data safely are defined within sound.h in
the form of PCM_READ_* / PCM_WRITE_*
* Currently, most of them are probably limited for mono/stereo handling,
but the future addition of true multichannel will be much easier.
- Low latency operation
* Well, this require lot more works to do not just within sound driver,
but we're heading towards right direction. Buffer/block sizing within
channel.c is rewritten to calculate precise allocation for various
combination of sample/data/rate size. As a result, applying correct
SNDCTL_DSP_POLICY value will achive expected latency behaviour simmilar
to what commercial 4front driver do.
* Signal handling fix. ctrl+c of "cat /dev/zero > /dev/dsp" does not
result long delay.
* Eliminate sound truncation if the sound data is too small.
DIY:
1) Download / extract
http://people.freebsd.org/~ariff/lowlatency/shortfiles.tar.gz
2) Do a comparison between "cat state*.au > /dev/dsp" and
"for x in state*.au ; do cat $x > /dev/dsp ; done"
- there should be no "perceivable" differences.
Double close for PR kern/31445.
CAVEAT: Low latency come with (unbearable) price especially for poorly
written applications. Applications that trying to act smarter
by requesting (wrong) blocksize/blockcount will suffer the most.
Fixup samples/patches can be found at:
http://people.freebsd.org/~ariff/ports/
- Switch minimum/maximum sampling rate limit to "1" and "2016000" (48k * 42)
due to closer compatibility with 4front driver.
Discussed with: marcus@ (long time ago?)
- All driver specific sysctls in the form of "hw.snd.pcm%d.*" have been
moved to their own dev sysctl nodes, notably:
hw.snd.pcm%d.vchans -> dev.pcm.%d.vchans
Bump __FreeBSD_version.
Driver specific
---------------
- Ditto for sysctls.
- snd_atiixp, snd_es137x, snd_via8233, snd_hda
* Numerous cleanups and fixes.
* _EXPERIMENTAL_ polling mode support using simple callout_* mechanisme.
This was intended for pure debugging and latency measurement, but proven
good enough in few unexpected and rare cases (such as problematic shared
IRQ with GIANT devices - USB). Polling can be enabled/disabled through
dev.pcm.0.polling. Disabled by default.
- snd_ich
* Fix possible overflow during speed calibration. Delay final
initialization (pcm_setstatus) after calibration finished.
PR: kern/100169
Tested by: Kevin Overman <oberman@es.net>
* Inverted EAPD for few Nec VersaPro.
PR: kern/104715
Submitted by: KAWATA Masahiko <kawata@mta.biglobe.ne.jp>
Thanks to various people, notably Joel Dahl, Yuriy Tsibizov, Kevin Oberman,
those at #freebsd-azalia @ freenode and others for testing.
Joel Dahl will do the manpage update.
- incorporate csjp's fix for a mishandled endian conversion
- convert PAGE_SIZE to 4096 for PCIe adapter workaround (my page size is not 4k)
- implement em_read_pcie_cap_reg where we set the max read size on pcie to 4k (taken from mxge)
Reviewed by: scottl and jfvogel
I have been debugging the usb problems some more. Your were
right in your assumption (thanks for the pointer) about lack
of calls to bus_dmamap_sync(). In usbdi.c bus_dmamap_sync()
does get used for transfers that move data from PC to USB and
it is used for transfers that move data from USB to PC. But
someone forgot that control transfers consist of possibly two
data chunks : the request itself and optionally a buffer of
data that should be transfered to or from the USB device. On
requests to the control endpoint without additional data
bus_dmamap_sync() didn't get called. For some reason my first
tests with umass worked (due to enough cache poisening I
guess). The attached patch adds a call to bus_dmamap_sync()
to usbdi.c and now all devices I have tried work out of the
box. I have successfully transfered large files using the
if_axe driver and I have mounted several different umass
devices.
submitted by: Daan Vreeken
sponsored by: Vitsch Electronics
reviewed by: cognet@
- Fix bug preventing adoption of running firmware
- Set PCIe max read request size to 4KB
- Read PCIe link width from config space
- Assume aligned completions from the southbridge ports
of intel E5000 chips
- Use aligned firmware when link width is x4 or less
- Add hw.mxge.force_firmware tunable to allow user to force
selection of aligned (or unaligned) firmware
bfe_init_locked() wasn't sufficient to bring the chip back to life, it also
required a call to bfe_chip_reset() during resume.
Tested by: Stepan Zastupov +redchrom at gmail+
MFC after: 1 week
archs. [1]
- Instead of bus_space_{read,write}*(rman_get_bustag(), rman_get_bushandle())
use bus_{read,write}*() for efficiency.
Reported by: Peter Losher [1]
Tested on: i386, sparc64
MFC after: 2 weeks
made to accommodate the chip being in promiscuous mode while
offloading VLAN tag processing to the hardware. We can now
properly handle the absence of VLAN tags from hardware stripping.
Reviewed by: rwatson, andre
MFC after: 1 month
after calling mfi_mapcmd is no longer needed, so long as the MFI_CMD_POLLED
flag is set. This change eliminates the possibility of a polled command
getting posted twice to the driver. This is turn fixes panics on shutdown
when INVARIANTS is set.
Sponsored by: Ironport
and provied an isp_control entry point so that the outer layers can
do PLOGI/LOGO explicitly. Add MS IOCB support. This completes the cycle
for base support for SMI-S.
This allows us to play nicely on SANs when we have target mode
enabled in f/w but have neither the scsi_targbh enabled or
scsi_targ with a target enabled.
accidentally truncating off the VLAN tag field in the TX descriptor. Fix
this by splitting up the vlan_tag and flags fields into separate fields,
and handling them appropriately.
Sponsored by: Ironport
MFC After: 3 days
descriptor's mbuf pointer to see if the transmit ring is full. The
mbuf pointer is set only in the last descriptor of a
multi-descriptor packet. By relying on the mbuf pointers of the
earlier descriptors, the driver would sometimes overwrite a
descriptor belonging to a packet that wasn't completed yet. Also,
tx_chain_prod wasn't updated inside the loop, causing the wrong
descriptor to be checked after the first iteration. The upshot of
all this was the loss of some transmitted packets at medium to high
packet rates.
In bce_tx_encap, remove a couple of old statements that shuffled
around the tx_mbuf_map pointers. These now correspond 1-to-1 with
the transmit descriptors, and they are not supposed to be changed.
Correct a couple of inaccurate comments.
MFC after: 1 month
Only complain about FC Reponse errors if they're nonzero.
Shorten some PortID printouts for local loop.
Add an internal isp_xcmd_t data structure which we'll use for some
CT-Passthru support as part of adding SMI-S.
- Add a translation so the Linux ioctl's don't conflict with
the FreeBSD definition.
- Assume Linux 32bit emulation on amd64.
This was tested on i386 and amd64 with the 32bit Linux MegaCli.
Eventually we should do a 32bit native FreeBSD translation app.
gone device timers and zombie state entries. There are tunables
that can be used to select a number of parameters.
loop_down_limit - how long to wait for loop to come back up before
declaring
all devices dead (default 300 seconds)
gone_device_time- how long to wait for a device that has appeared
to leave the loop or fabric to reappear (default 30 seconds)
Internal tunables include (which should be externalized):
quick_boot_time- how long to wait when booting for loop to come up
change_is_bad- whether or not to accept devices with the same
WWNN/WWPN that reappear at a different PortID as being the 'same'
device.
Keen students of some of the subtle issues here will ask how
one can keep devices from being re-accepted at all (the answer
is to set a gone_device_time to zero- that effectively would
be the same thing).
- Add 3 new functions to the pci_if interface along with suitable wrappers
to provide the device driver visible API:
- pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count'
here is an in and out parameter. The driver stores the desired number
of messages in '*count' before calling the function. On success,
'*count' holds the number of messages allocated to the device. Also on
success, the driver can access the messages as SYS_RES_IRQ resources
starting at rid 1. Note that the legacy INTx interrupt resource will
not be available when using MSI. Note that this function will allocate
either MSI or MSI-X messages depending on the devices capabilities and
the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note
that the driver should activate the memory resource that holds the
MSI-X table and pending bit array (PBA) before calling this function
if the device supports MSI-X.
- pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function
releases the messages allocated for this device. All of the
SYS_RES_IRQ resources need to be released for this function to succeed.
- pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns
the maximum number of MSI or MSI-X messages supported by this device.
MSI-X is preferred if present, but this function will honor the
'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function
should return the largest value that pci_alloc_msi() can return
(assuming the MD code is able to allocate sufficient backing resources
for all of the messages).
- Add default implementations for these 3 methods to the pci_driver generic
PCI bus driver. (The various other PCI bus drivers such as for ACPI and
OFW will inherit these default implementations.) This default
implementation depends on 4 new pcib_if methods that bubble up through
the PCI bridges to the MD code to allocate IRQ values and perform any
needed MD setup code needed:
- PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages.
- PCIB_RELEASE_MSI() releases a group of MSI messages.
- PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message.
- PCIB_RELEASE_MSIX() releases a single MSI-X message.
- Add default implementations for these 4 methods that just pass the
request up to the parent bus's parent bridge driver and use the
default implementation in the various MI PCI bridge drivers.
- Add MI functions for use by MD code when managing MSI and MSI-X
interrupts:
- pci_enable_msi(dev, address, data) programs the MSI capability address
and data registers for a group of MSI messages
- pci_enable_msix(dev, index, address, data) initializes a single MSI-X
message in the MSI-X table
- pci_mask_msix(dev, index) masks a single MSI-X message
- pci_unmask_msix(dev, index) unmasks a single MSI-X message
- pci_pending_msix(dev, index) returns true if the specified MSI-X
message is currently pending
- Save the MSI capability address and data registers in the pci_cfgreg
block in a PCI devices ivars and restore the values when a device is
resumed. Note that the MSI-X table is not currently restored during
resume.
- Add constants for MSI-X register offsets and fields.
- Record interesting data about any MSI-X capability blocks we come
across in the pci_cfgreg block in the ivars for PCI devices.
Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X)
Reviewed by: scottl, grehan, jfv
MFC after: 2 months
our own watchdog that piggybacks on the em_local_timer() routine.
We suppose that the if_timer/if_watchdog interface should be
obsoleted, since it doesn't fit the modern SMP network stack.
NIC drivers should create their own watchdogs, that check and
clear the timers always holding driver's lock.
In collaboration with: jfv, scottl
- Only call iwi_stop() if we got far enough along in iwi_attach() to
alloc an ifnet.
- Release the firmware after stopping the interface and detaching the
ifnet.
MFC after: 1 month
Reviewed by: sam
to be switched to is saved in sc->delayed_next_scr and
the actual switch is performed later. It was possible
to get into the endless loop when attempting to switch
to a closed vty (which is not allowed and beep-alerted
when attempted) and when the visual beep was in effect.
This caused sc->delayed_next_scr to never be reset and
endless attempts to switch to a closed vty and endless
visual beeping. How to repeat:
- boot into single-user
- run "kbdcontrol -b visual"
- quickly press Alt+F2 two times
PR: kern/68016
X-MFC after: 6.2-RELEASE
specific privilege names to a broad range of privileges. These may
require some future tweaking.
Sponsored by: nCircle Network Security, Inc.
Obtained from: TrustedBSD Project
Discussed on: arch@
Reviewed (at least in part) by: mlaier, jmg, pjd, bde, ceri,
Alex Lyashkov <umka at sevcity dot net>,
Skip Ford <skip dot ford at verizon dot net>,
Antoine Brodin <antoine dot brodin at laposte dot net>
as we have no use for that info. Instead let this function return the
keyboard ID and verify at its invocation in sunkbd_configure() that we're
talking to a Sun type 4/5/6 keyboard, i.e. a keyboard supported by this
driver.
- Add an option SUNKBD_EMULATE_ATKBD whose code is based on the respective
code in ukbd(4) and like UKBD_EMULATE_ATSCANCODE causes this driver to
emit AT keyboard/KB_101 compatible scan codes in K_RAW mode as assumed by
kbdmux(4). Unlike UKBD_EMULATE_ATSCANCODE, SUNKBD_EMULATE_ATKBD also
triggers the use of AT keyboard maps and thus allows to use the map files
in share/syscons/keymaps with this driver at the cost of an additional
translation (in ukbd(4) this just is the way of operation).
- Implement an option SUNKBD_DFLT_KEYMAP, which like the equivalent options
of the other keyboard drivers allows to specify the default in-kernel
keyboard map. For obvious reasons this made to only work when also using
SUNKBD_EMULATE_ATKBD.
- Implement sunkbd_check(), sunkbd_check_char() and sunkbd_clear_state(),
which are also required for interoperability with kbdmux(4).
- Implement K_CODE mode and FreeBSD keypad compose.
- As a minor hack define KBD_DFLT_KEYMAP also in the !SUNKBD_EMULATE_ATKBD
case so we can obtain fkey_tab from <dev/kbd/kbdtables.h> rather than
having to duplicate it and #ifdef some more code.
- Don't use the TX-buffer for writing the two command bytes for setting the
keyboard LEDs as this consequently requires a hardware FIFO that is at
least two bytes in depth, which the NMOS-variant of the Zilog SCCs doesn't
have. Thus use an inlined version of uart_putc() to consecutively write
the command bytes (a cleaner approach would be to do this via the soft
interrupt handler but that variant wouldn't work while in ddb(4)). [1]
- Fix some minor style(9) bugs.
PR: 90316 [1]
Reviewed by: marcel [1]
BIO_READ/BIO_WRITE is sent to vnode-backed provider (BIO_DELETE or
BIO_FLUSH).
Reported by: ceri
Add support for BIO_FLUSH to vnode-backed md(4) devices based on
VOP_FSYNC().
- Test the mac_type rather than if_hwassist (since ifp doesn't exist yet)
to determine if the adapter supports TSO and thus to change the sizes
for the bus_dma tag.
Reviewed by: glebius
during detach() similar to other NIC drivers rather than allocating them
during init() and freeing them during stop():
- Move creation of tx bus_dma tag amd maps and tx_buffer_area from
em_setup_transmit_structures() to em_allocate_transmit_structures().
- Call em_allocate_xxx_structures() in em_attach().
- Only call em_free_xxx_structures() in em_detach().
- Change em_setup_xxx_structures() to free any existing tx or rx buffers
and in the case of rx repopulate the ring with newer buffers.
Reviewed by: jfv
the EOP descriptor in the first descriptor of the packet. And then
in em_txeof() search for DD bits set only in the EOP descriptors,
embedding the cleanup of all packet's descriptors into inner loop.
This change is important for future chips, where DD bit is going
to be set only on the EOP descriptors.
Submitted by: jfv
Details:
o if_em.c changes:
- Added several new PCI ids.
- Check em_check_phy_reset_block() before doing SIOCSIFMEDIA ioctl.
- Don't touch TARC registers, they are now handled in shared
code in if_em_hw.c.
- Move RDH and RDT setting to the end of
em_initialize_receive_unit().
- Declare em_read_pcie_cap_reg(), now empty.
o if_em_hw.c dropped in from vendor, then restored rev. 1.15.
o if_em_hw.h dropped in from vendor, then modified:
- Added RX overrun interrupt flag to interrupt enable mask.
- Remove declarations of em_io_read(), em_io_write().
Approved by: jfv
the CAM_NEW_TRAN_CODE that has been in the tree for some years now.
This first step consists solely of adding to or correcting
CAM_NEW_TRAN_CODE pieces in the kernel source tree such
that a both a GENERIC (at least on i386) and a LINT build
with CAM_NEW_TRAN_CODE as an option will compile correctly
and run (at least with some the h/w I have).
After a short settle time, the other pieces (making
CAM_NEW_TRAN_CODE the default and updating libcam
and camcontrol) will be brought in.
This will be an incompatible change in that the size of structures
related to XPT_PATH_INQ and XPT_{GET,SET}_TRAN_SETTINGS change
in both size and content. However, basic system operation and
basic system utilities work well enough with this change.
Reviewed by: freebsd-scsi and specific stakeholders
only those bars that had addresses assigned by the BIOS and where the
bridges were properly programmed. Now even unprogrammed ones work.
This was needed for sun4v. We still only implement up to 2GB memory
ranges, even for 64-bit bars. PCI standards at least through 2.2 say
that this is the max (or 1GB is, I only know it is < 32bits).
o Always define pci_addr_t as uint64_t. A pci address is always 64-bits,
but some hosts can't address all of them.
o Preserve the upper half of the 64-bit word during resource probing.
o Test to make sure that 64-bit values can fit in a u_long (true on some
platforms, but not others). Don't use those that can't.
o minor pedantry about data sizes.
o Better bridge resource reporting in bootverbose case.
o Minor formatting changes to cope with different data types on different
platforms.
Submitted by: jmg, with many changes by me to fully support 64-bit
addresses.
Though it is named after overclocking tool for ASUS motherboards,
it is not capable to change clock ratio or CPU core voltage.
This driver exports Templature, Power output voltage, Fan RPM under
dev.acpi_aiboost.0.*.
Descriptions for these values are set to sysctl describe, which can be
get by sysctl -d.
in #ifdef __NO_STRICT_ALIGNMENT rather than #ifdef __i386__. This
means that amd64 now also uses the optimized code. [1]
While at it, fix a nearby style(9) bug.
- Remove the hw.dc_quick SYSCTL, which allowed to turn off the above
mentioned optimization, as like the equivalent and already removed
- In dc_setcfg() suppress printing a warning when forcing the receiver
and transceiver to idle state times out for chips where the status
bits in question just never change (observed in detail with DM9102A)
and therefore the warning would be highly likely false positive. [2]
- In dc_ifmedia_sts() add a missing DC_UNLOCK().
Tested by: Hans-Joerg Sirtl on amd64 [1]
PR: 82681 [2]
Obtained from: NetBSD tlp(4) [2]
MFC after: 1 week
Rename MAX_SAMPLE_RATES macro to OSS_MAX_SAMPLE_RATES. The old
macro clashed with those used in other applications and libaries
(ex: RtAudio). 4Front responded by updating their spec, so we
will follow suit.
Submitted by: ryanb
Noticed by: pointyhat/kris
new device support, and it is hoped a more stable driver for 6.2. RELEASE.
This checkin was discussed and approved today by RE, scottl, jhb, and pdeuskar
keyboard is attached only after the system has already booted.
If USB keyboard is also present, and there's no kbdmux(4), the problem
has been hiding itself because as soon as we get to multi-user, the
USB keyboard becomes an active keyboard (see devd.conf), thus marking
atkbd inactive and letting the old code initialize the keyboard.
With kbdmux(4), or if there's no USB keyboard, the atkbd keyboard is
always active, whether it's physically attached or not, thus it never
initialized itself properly on a physical attach.
To fix this, move block that initialized the keyboard on attach upper
so it doesn't depend on the (KBD_IS_ACTIVE(kbd) && KBD_IS_BUSY(kbd))
condition. Also move KBD_FOUND_DEVICE() a few lines upper so that
KDSETLED and KDSETREPEAT that follow it propagate to the controller.
MFC after: 3 days
: revision 1.27
: date: 2000/05/28 12:43:24; author: ache; state: Exp; lines: +3 -2
: Manipulate with AltGR Led (really CapsLock Led) only in K_XLATE mode, because
: all other modes not set ALKED flag and it means that CapsLock always turned
: off for them.
: Real bug example is X11 which never turn on CapsLock with Russian keyboard.
:
: PR: 18651
: Submitted by: "Mike E. Matsnev" <mike@po.cs.msu.su>
MFC after: 3 days
and TCP checksum offloading fine, it only has a problem with IP checksums on
IP fragments.. Barring a fix or workaround available from the hardware, the
real solution would be to have finer grained control in the stack over what
can and cannot be assisted in hardware.
yet to be investigated circumstances. If that happens truncate to the number
of rates that the firmware supports.
Found by: Jeremie Le Hen
Obtained from: OpenBSD (w/ changes)
MFC after: 3 days
kept unused in the ring. This check should probably be moved up to
bce_start_locked at some point, as it'll make the loop up there slightly
more efficient, and will eliminate a costly set of busdma operations when
the ring is full. But this works for now.
This makes all of my UDP torture tests work. I'll cautiously say that
it might even work for other users now. Feedback is appreciated.
If the length is zero, catch this early, instead of making dflen go negative
and letting bad things happen... We also check to see if RV (checksum) is
0, and handle that has a checksum failure...
Properly handle checksum failures by not processing read-write VPD data,
and removing all the found read-only data...
Tested by: oleg (dflen going negative)
should be easily adapted to SD 2.0 (aka SDHC), SDIO, MMC and MMCplus
cards. At the present time, there's only one bridge driver for the
ARM9 based Atmel AT91RM9200.
tasks. Since the host controllers rely on tasks to process transfer
timeouts, if a synchronous transfer from a driver was invoked from
a task and timed out, it would never complete because the single
task thread was stuck performing the synchronous transfer so couldn't
process the timeout.
This affected the axe, udav and ural drivers.
Problem hardware provided by: guido
long being DMA'ed 2 (or 1) bytes past the end of the mbuf and corrupting
random kernel memory. I had forgotten about the 2 bytes of implict
padding the firmware assumes.
Sponsored by: Myricom Inc.
- Fix the locking protocol to eliminate races between normal I/O and AENs.
- Various small improvements and usability tweaks.
Sponsored by: IronPort
Portions Submitted by: Doug Ambrisko
- Use bus_dmamap_load_mbuf_sg() to eliminate the need for the callback and
all of the extra bookkeeping associated with it.
- Eliminate the bce_dmamap_arg structure and streamline the memory allocation
routines to not need it. This does change some of the debugging messages.
- Refactor the loop that fills the buffer descriptor so that it can be done
with a single set of logic in a single loop instead of two sets of logic.
- Eliminate the need to cache and pass descriptor indexes between the start
loop and the encap function.
- Change the start loop to always check the ifnet sendq for more work.
This significantly helps the driver withstand large UDP workloads, though
it's still not perfect. I suspect the remaining work lies with handling
the OACTIVE flag, and also in possibly streamlining the interrupt handler
some. It is, however, nearly on par with the other popular gigabit drivers
in terms of stability now.
- Add entries in the uscanner.4 man page (along with missing 3500).
PR: usb/100957 [1], usb/100992 [2]
Submitted by: Jim Teresco <terescoj@teresco.org> [1],
Walter C. Pelissero <walter.pelissero@iesy.net> [2]
MFC after: 3 days
will fix a problem where you boot w/ the default of autoselect, but then
set the speed to 100/full, the switch will keep the autoselect/100/full
negotiation... This will continue to work till someone resets the switch
or unplugs the cable resulting in the switch failing to autoneg and falling
back to 100/half, causing a hard to track down duplex mismatch..
Submitted by: nCircle Network Security, Inc.
MFC after: 1 week
- Add support for the Conexant Waikiki/CX20551-22, found
in most Toshiba P100 series laptops. Despite of growing
urban legend of "unsupported Conexant", this codec is fully
supported in this driver.
Note: Toshiba P100 has broken (acpi) BIOS, thus rendering
its soundchip useless. Please disable ACPI, or get
BIOS updates (if any).
Found/tested by: Vulpes Velox <v.velox@vvelox.net>
URL: http://lists.freebsd.org/pipermail/freebsd-multimedia/2006-September/004896.html
- Parser cleanups to handle possible oss/mixer collision. Found
after parsing Conexant Waikiki nodes.
- Increase resilient against resource failure during attach/detach.
- Implement simple config through hint.pcm.<unit>.config. Supported
options:
gpio0 (default on Acer), gpio1, gpio2, softpcmvol,
fixedrate (default), forcestereo (default)
* Option prefixed with "no" (such as "nofixedrate") will do
the opposite.
* Options can be separated using space " " or comma ",".
* The "no" option will take precedence over anything else.
Example:
hint.pcm.0.config="gpio2,nofixedrate,noforcestereo,nogpio0,softpcmvol"
hint.pcm.0.config="softpcmvol noforcestereo"
or not the OS has to wait for RX_RDY or TX_RDY to be set before the OS sets
the control code in the control/status register. Looking at the interface
design, it seems that RX_RDY and TX_RDY are probably there to protect
access to the data register and have nothing to do with the control/status
register. Nevertheless, try to take what I think is the more conservative
approach and always wait for the appropriate [TR]X_RDY flag to be set
before writing any of the WR_NEXT, WR_END, RD_START, or RD_NEXT control
codes to the control/status register.
close and re-open the default pipe instead of relying on the host
controller driver to notice the changes. Remove the unreliable code
that attempted to update these fields while the pipe was active.
This fixes a case where the hardware could cache and continue to
use the old address, resulting in a "getting first desc failed"
error.
PR: usb/103167
- Fix support for ASUS M5200ae (buggy BIOS)
- Fix few problems, reported by Coverity Prevent (TM).
CID: 246991, 246676, 246675, 246674, 246477
Found by: Coverity Prevent (TM)
The parallel LINT build sometimes broke if kernel-depend wasn't
fast enough in generating ukbdmap.h. If someone thinks this
option would still be useful for the module, a proper fix is
to add the code generating ukbdmap.h into modules/ukbd/Makefile
and backing this change out.
Add support for Intel High Definition Audio Controller.
This driver make a special guarantee that "playback" works
on majority hardwares with minimal or without specific vendor
quirk.
This driver is a product of collaborative effort made by:
Stephane E. Potvin <sepotvin@videotron.ca>
Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Wesley Morgan <morganw@chemikals.org>
Daniel Eischen <deischen@FreeBSD.org>
Maxime Guillaud <bsd-ports@mguillaud.net>
Ariff Abdullah <ariff@FreeBSD.org>
....and various people from freebsd-multimedia@FreeBSD.org
Refer to snd_hda(4) for features and issues.
Welcome To HDA.
Sponsored by: Defenxis Sdn. Bhd.
This driver make a special guarantee that "playback" works
on majority hardwares with minimal or without specific vendor
quirk.
This driver is a product of collaborative effort made by:
Stephane E. Potvin <sepotvin@videotron.ca>
Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Wesley Morgan <morganw@chemikals.org>
Daniel Eischen <deischen@FreeBSD.org>
Maxime Guillaud <bsd-ports@mguillaud.net>
Ariff Abdullah <ariff@FreeBSD.org>
....and various people from freebsd-multimedia@FreeBSD.org
Refer to snd_hda(4) for features and issues.
Welcome To HDA.
Sponsored by: Defenxis Sdn. Bhd.
- fix multiple initialization of the first codec (support for more than
one codec should be added in the future)
- use spicds instead of ak452x module
Submitted by: "Konstantin Dimitrov" <kosio.dimitrov@gmail.com>
stripping was disabled due to being in promisc mode. This is a hardware
bug. Update comment to explicitly state the reason the manual vlan tag
insertion in this case. See rev. 1.53 for further information as well.
Noticed by: jhb
generic vlan_start() takes care of it when vlan hardware insertion is disabled.
In em_set_promisc() add a note that BPF may also be enabled without going into
promisc mode.
Reviewed by: jfv
IP options and add skeleton IPv6 support. The new code structure can also be
easily enhanced to support new/more protocols (SCTP) in the future.
Reviewed by: jfv
and add skeleton IPv6 support. The new code structure can also be easily
enhanced to support new/more protocols (SCTP) and IP fragmentation in the
future.
In em_encap() only try to do TSO if 'dotso' is true.
Reviewed by: jfv
- EFBIG means the mbuf chain was too long and bus_dma ran out of segments.
Defragment the mbuf chain and try again. (Already existed, not changed.)
- ENOMEM means bus_dma could not obtain enough bounce buffers at this point
in time. Defer sending and try again later.
- All other errors, in particular EINVAL, are fatal and prevent the mbuf
chain from ever going through. Drop it and report error.
- Checking (nsegs == 0) is unnecessary as bus_dmamap_load_mbuf_sg() always
reports an error if it is < 1.
This prevents broken packets from clogging the interface queue indefinately.
Discussed with: scottl
Reviewed by: jfv
commit.
1) sys/dev/sound/pcm/sound.h
sys/dev/sound/pcm/channel.c
* Be more specific: SD_F_SOFTVOL -> SD_F_SOFTPCMVOL
2) sys/dev/sound/pcm/mixer.[ch]
* Implement
mix_setparentchild()
mix_setrealdev()
mix_getparent()
mix_getchild()
The purpose of these functions is implement relative volume
adjustment, such as to tie two or more mixer device into a
single logical device. Usefull for the upcoming HDA driver
and few AC97 codec (such as AD1981B) where the master volume
"vol" need to be implemented using this logical manner.
3) sys/dev/sound/pcm/ac97_patch.[ch]
* Patch for AD1981B codec to enable (automuting) headphone jack sense.
4) sys/dev/sound/pcm/ac97.c
* Implement proper logical master volume for AD9181B codec
through various mix_set{parentchild,realdev}(). Tie both
"ogain" (headphone volume) and "phone" (speaker/lineout) to
a logical "vol".
5) sys/dev/sound/pcm/usb/uaudio_pcm.c
* ditto, for "vol" -> { "pcm" }.
MFC after: 1 month
ioctls passing integer arguments should use the _IOWINT() macro.
This fixes a lot of ioctl's not working on sparc64, most notable
being keyboard/syscons ioctls.
Full ABI compatibility is provided, with the bonus of fixing the
handling of old ioctls on sparc64.
Reviewed by: bde (with contributions)
Tested by: emax, marius
MFC after: 1 week
The key problem was that the aperture size detection using the MSAC bit
doesn't work -- the bit appears to be set even when it shouldn't be. Linux
takes a different approach, testing for a bit of the GMADR (PCIR_BAR(2)) being
set. However, as I don't think that's a safe way to test aperture size, we
just allocate the resource and check its size. This also pointed out that
agp_generic_attach hadn't been allocating our aperture resource, which may
have caused problems in some cases.
Also corrected is a minor copy-and-pasteo in an error case.
PR: kern/103079
Submitted by: mnag
Tested on: i945GM, i915GM
MFC after: 2 weeks
The goal was to sync with the OSSv4 API 4Front Technologies uses in their
proprietary OSS driver. This was successful as far as possible. The part
of the API which is stable is implemented, for the rest there are some
stubs already.
New system ioctls:
- SNDCTL_SYSINFO - obtain audio system info (version, # of audio/midi/
mixer devices, etc.)
- SNDCTL_AUDIOINFO - fetch details about a specific audio device
- SNDCTL_MIXERINFO - fetch details about a specific mixer device
New audio ioctls:
- Sync groups (SNDCTL_DSP_SYNCGROUP/SNDCTL_DSP_SYNCSTART) which allow
triggered playback/recording on multiple devices (even across processes
simultaneously).
- Peak meters (SNDCTL_DSP_GETIPEAKS/SNDCTL_DSP_GETOPEAKS) - can query
audio drivers for peak levels (needs driver support, disabled for now).
- Per channel playback/recording levels -
SNDCTL_DSP_{GET,SET}{PLAY,REC}VOL. Note that these are still in name
only, just wrapping around the AC97-style mixer at the moment. The next
step is to push them down to the drivers.
Audio ioctls still under development by 4Front (for which stubs may exist
in this commit):
- SNDCTL_GETNAME, SNDCTL_{GET,SET}{SONG,LABEL}
- SNDCTL_DSP_{GET,SET}_CHNORDER
- SNDCTL_MIX_ENUMINFO, SNDCTL_MIX_EXTINFO - (might be documented enough in
the OSS releases to work on this. These ioctls cover the cool "twiddle
any knob on your card" features.)
Missing:
- SNDCTL_DSP_COOKEDMODE -- this ioctl is used to give applications direct
access to a card's buffers, bypassing the feeder architecture. It's
a toughy -- "someone" needs to decide :
(a) if this is desireable, and (b) if it's reasonably feasible.
Updates for driver writers:
So far, only two routines to the channel class (in channel_if.m) are added.
One is for fetching a list of discrete supported playback/recording rates
of a channel, and the other is for fetching peak level info (useful for
drawing peak meters). Interested parties may want to help pushing down
SNDCTL_DSP_{GET,SET}{PLAY,REC}VOL into the drivers.
To use the new stuff you need to rebuild the sound drivers or your kernel
(depending on if you use modules or not) and to install soundcard.h (a
buildworld/installworld handles this).
Sponsored by: Google SoC 2006
Submitted by: ryanb
Many thanks to: 4Front Technologies for their cooperation, explanations
and the nice license of their soundcard.h.
- Split out the communication protocols into their own files and use
a couple of function pointers in the softc that the commuication
protocols setup in their own attach routine.
- Add support for the SSIF interface (talking to IPMI over SMBus).
- Add an ACPI attachment.
- Add a PCI attachment that attaches to devices with the IPMI interface
subclass.
- Split the ISA attachment out into its own file: ipmi_isa.c.
- Change the code to probe the SMBIOS table for an IPMI entry to just use
pmap_mapbios() to map the table in rather than trying to setup a fake
resource on an isa device and then activating the resource to map in the
table.
- Make bus attachments leaner by adding attach functions for each
communication interface (ipmi_kcs_attach(), ipmi_smic_attach(), etc.)
that setup per-interface data.
- Formalize the model used by the driver to handle requests by adding an
explicit struct ipmi_request object that holds the state of a given
request and reply for the entire lifetime of the request. By bundling
the request into an object, it is easier to add retry logic to the various
communication backends (as well as eventually support BT mode which uses
a slightly different message format than KCS, SMIC, and SSIF).
- Add a per-softc lock and remove D_NEEDGIANT as the driver is now MPSAFE.
- Add 32-bit compatibility ioctl shims so you can use a 32-bit ipmitool
on FreeBSD/amd64.
- Add ipmi(4) to i386 and amd64 NOTES.
Submitted by: ambrisko (large portions of 2 and 3)
Sponsored by: IronPort Systems, Yahoo!
MFC after: 6 days
Unfortunately, the QUEUE FULL event only tells you Bus && Target.
It doesn't tell you lun. In order for the XPT_REL_SIMQ action to
work, we have to have a real lun. But which one? For now, just
iterate over MPT_MAX_LUNS.
Practically speaking, this is only going to be happening for lower
quality SAS or SATA drives behind the SAS controller, which means
only lun 0, so it's not so bad.
Helpful Reminder Nagging from: John Baldwin, Fred Whiteside
MFC after: 5 days
of the chip to let ASF/IPMI firmware to respond to IPMI after attaching
and when the chip is down. David looked at it but could really say
what they right minimal config. stuff would be. It's not documented.
I figured this out via trial and error.
Reviewed by: davidch
is incorrect, and causes endianness bugs on 64-bit big-endian
machines (sparc64), it's the best choice for now, as many of
these IOCTLs are used inside the kernel, and bogusly pass an
argument as "int *" which results in unaligned access panics
on sparc64 when attempting to dereference them via *(intptr_t *).
(Several of us are working on a real fix, which is uneasy.)
part of the hal distribution early on when the hal was built for
each os but it's been portable for a long time so move the os-specific
code out (and off the vendor branch)
o correct the copyright on ah_osdep.?; it was mistakenly given a
restricted license and not a dual-bsd/gpl license
o remove the module api definition as it was never used
o fixup include paths for move of ah_osdep.h
MFC after: 2 weeks
with other commonly used sysctl name spaces, rather than declaring them
all over the place.
MFC after: 1 month
Sponsored by: nCircle Network Security, Inc.
m_pkthdr.ether_vlan. The presence of the M_VLANTAG flag on the mbuf
signifies the presence and validity of its content.
Drivers that support hardware VLAN tag stripping fill in the received
VLAN tag (containing both vlan and priority information) into the
ether_vtag mbuf packet header field:
m->m_pkthdr.ether_vtag = vlan_id; /* ntohs()? */
m->m_flags |= M_VLANTAG;
to mark the packet m with the specified VLAN tag.
On output the driver should check the mbuf for the M_VLANTAG flag to
see if a VLAN tag is present and valid:
if (m->m_flags & M_VLANTAG) {
... = m->m_pkthdr.ether_vtag; /* htons()? */
... pass tag to hardware ...
}
VLAN tags are stored in host byte order. Byte swapping may be necessary.
(Note: This driver conversion was mechanic and did not add or remove any
byte swapping in the drivers.)
Remove zone_mtag_vlan UMA zone and MTAG_VLAN definition. No more tag
memory allocation have to be done.
Reviewed by: thompsa, yar
Sponsored by: TCP/IP Optimization Fundraise 2005
- Added support for multicast filtering, now that the firmware
supports it. Note that this is not yet tested, as multicast
seems to panic -current (even w/o mxge loaded)
- Added workaround to cope with different irq data struct size on
pre-multicast firmware which can found running on nics.
- Added Intel E5000 PCIe chipsets to list providing aligned completions.
- Replaced various magic constants with #defines, now that they are
defined in the firmware headers.
in the transmit busdma tag, so I moved the segment list off the
stack.
- Fixed transmit routine to ensure it doesn't read past the end
of an mbuf when parsing headers.
- Corrected handling of odd length segments. Setting MXGEFW_FLAGS_ALIGN_ODD
is required only when offloading the checksum of that frame.
Sponsored by: Myricom Inc.
if_watchdog, etc., or in functions used only in these methods.
In all other functions in the driver use device_printf().
- Use __func__ instead of typing function name.
Submitted by: Alex Lyashkov <umka sevcity.net>
if_ioctl, if_watchdog, etc, or in functions that are used by
these methods only. In all other cases use device_printf().
This also fixes several panics, when if_printf() is called before
softc->ifp was initialized.
Submitted by: Alex Lyashkov <umka sevcity.net>
in syscons. This replaces a simple access semaphore that was assumed to be
protected by Giant but often was not. If two threads that were otherwise
SMP-safe called printf at the same time, there was a high likelyhood that
the semaphore would get corrupted and result in a permanently frozen video
console. This is similar to what is already done in the serial console
drivers.
Instead, we want busses to explicitly specify an add_child routine if they
want to support identify routines, but by default disallow having outside
drivers add devices.
- Give smbus(4) an explicit bus_add_child() method.
Requested by: imp
- Change smbus_callback() to pass a void * rather than caddr_t.
- Change smbus_bread() to pass a pointer to the count and have it be an
in/out parameter. The input is the size of the buffer (same as before),
but on return it will contain the actual amount of data read back from
the bus. Note that this value may be larger than the input value. It
is up to the caller to treat this as an error if desired.
- Change the SMB_BREAD ioctl to write out the updated struct smbcmd which
will contain the actual number of bytes read in the 'count' field. To
preserve the previous ABI, the old ioctl value is mapped to SMB_OLD_BREAD
which doesn't copy the updated smbcmd back out to userland. I doubt anyone
actually used the old BREAD anyway as it was rediculous to do a bulk-read
but not tell the using program how much data was actually read.
- Make the smbus driver and devclass public in the smbus module and
push all the DRIVER_MODULE()'s for attaching the smbus driver to
various foosmb drivers out into the foosmb modules. This makes all
the foosmb logic centralized and allows new foosmb modules to be
self-contained w/o having to hack smbus.c everytime a new smbus driver
is added.
- Add a new SMB_EINVAL error bit and use it in place of EINVAL to return
an error for bad arguments (such as invalid counts for bread and bwrite).
- Map SMB bus error bits to EIO in smbus_error().
- Make the smbus driver call bus_generic_probe() and require child drivers
such as smb(4) to create device_t's via identify routines. Previously,
smbus just created one anonymous device during attach, and if you had
multiple drivers that could attach it was just random chance as to which
driver got to probe for the sole device_t first.
- Add a mutex to the smbus(4) softc and use it in place of dummy splhigh()
to protect the 'owner' field and perform necessary synchronization for
smbus_request_bus() and smbus_release_bus().
- Change the bread() and bwrite() methods of alpm(4), amdpm(4), and
viapm(4) to only perform a single transaction and not try to use a
loop of multiple transactions for a large request. The framing and
commands to use for a large transaction depend on the upper-layer
protocol (such as SSIF for IPMI over SMBus) from what I can tell, and the
smb(4) driver never allowed bulk read/writes of more than 32-bytes
anyway. The other smb drivers only performed single transactions.
- Fix buffer overflows in the bread() methods of ichsmb(4), alpm(4),
amdpm(4), amdsmb(4), intpm(4), and nfsmb(4).
- Use SMB_xxx errors in viapm(4).
- Destroy ichsmb(4)'s mutex after bus_generic_detach() to avoid problems
from child devices making smb upcalls that would use the mutex during
their detach methods.
MFC after: 1 week
Reviewed by: jmg (mostly)
to it. Try to co-operate with the IPMI/ASF firmware accessing the PHY.
One we get link we don't mess with the PHY. If we do then over time
the NIC will go off line. It would be nice if we could tell if IPMI
was enabled on the chip but I can't figure out a reliable way to do
that. The scheme I tried worked on a Dell PE850 but not on an HP machine.
So we assume any NIC that has ASF capability needs to deal with it.
The code was inspired by the support in Linux from kernel.org and Broadcom.
Broadcom did give me some info. but it is rather limited and is mostly
just what is in the Linux driver. Thanks to the numerous people that
helped debug the many prior versions and that I didn't break other
bge(4) HW.
Reviewed by: several people
Tested by: even more
Ever since rev 1.68 re(4) checks the validity of link in re_start.
But rlphy(4) got a garbled data due to a different bit layout used on
8139C+ and it couldn't report correct link state. To fix it, ignore
BMCR_LOOP and BMCR_ISO bits which have different meanings on 8139C+.
I think this also make dhclient(8) work on 8139C+.
Reported by: Gerrit Kuehn <gerrit AT pmp DOT uni-hannover DOT de>
Tested by: Gerrit Kuehn <gerrit AT pmp DOT uni-hannover DOT de>
is to able to be called after *all* attach and enable events are done.
We establish a SYSINIT hook to call this handler. The current usage for it
is to add scsi target resources *after* all enables are done. There seems
to be some dependencies between different halves of a dual-port with respect
to target mode.
Put in more meaningful event messages for some events- in particular
QUEUE FULL events so we can see what the queue depth was when the
IOC sent us this message.
MFC after: 1 week
- Add support for Intel 965 Express chipsets.
- Add support for R200 vertex programs, along with minor bugfixes.
- Add support for vblank synchronization to pipe B of Intel hardware
(laptop screens).
AEN. This makes the boot messages cleaner. I now know how this
structure works so I can implement it versus guessing. Remove the
not ready type code since it is ready now.
I added the time stamp/locale/class so people can parse messages better.
Create a sysctl so that we can set the locale/class level.
s/device_ptr_t/device_t/g
No md5 changes in the .o's
# Note to the md5 tracking club: $FreeBSD$ changes md5 after every commit
# so you need to checkout -kk to get $FreeBSD$ instead of the actual value
# of the keyword.
This helps systems that don't actually have atkbd controllers, such as the Intel
SBX82 blade, boot without device.hints hacks.
Hardware for this fix provided by iXsystems.
PR: 94822
Submitted by: Devon H. O'Dell <devon.odell@coyotepoint.com>
MFC After: 3 days
required by arches like sparc64 (not yet implemented) and sun4v where there
are seperate IOMMU's for each PCI bus... For all other arches, it will
end up returning NULL, which makes it a no-op...
Convert a few drivers (the ones we've been working w/ on sun4v) to the
new convection... Eventually all drivers will need to replace the parent
tag of NULL, w/ bus_get_dma_tag(dev), though dev is usually different for
each driver, and will require hand inspection...
Reviewed by: scottl (earlier version)
register. This really shouldn't be using pci_enable_io() directly as
bus_alloc_resource() does it already, but the cached copy of the
command word needs to be correct so the enable/disable mwi functions
work properly.
- Use pci bus accessors to read revision ID and subvendor IDs.
Reviewed by: jvogel
