mac-io bus, we cannot setup FAST interrupt handlers. This because we
use spinlocks to protect the hardware and all interrupt resources are
assigned the same interrupt handler. When the interrupt handler is
invoked for interrupt X, it could be preempted for interrupt Y while
it was holding the lock (where X and Y are the interrupt resources
corresponding a single instance of this driver). This is a deadlock.
By only using a MPSAFE handler in that case we prevent preemption.
The register layout has changed since the original NV4 - sigh.
Hotplug support has been fixed for all nVidia chipsets that supports it
(including the MCP51/55).
HW donated by: Kingsley College
locked.
- Move all the svr4 socket cache code into svr4_socket.c, specifically
move svr4_delete_socket() over from streams.c. Make the socket cache
entry structure and svr4_head private to svr4_socket.c as a result.
- Add a mutex to protect the svr4 socket cache.
- Change svr4_find_socket() to copy the sockaddr_un struct into a
caller-supplied sockaddr_un rather than giving the caller a pointer to
our internal one. This removes the one case where code outside of
svr4_socket.c could access data in the cache.
- Add an eventhandler for process_exit and process_exec to purge the cache
of any entries for the exiting or execing process.
- Add methods to init and destroy the socket cache and call them from the
svr4 ABI module's event handler.
- Conditionally grab Giant around socreate() in streamsopen().
- Use fdclose() instead of inlining it in streamsopen() when handling
socreate() failure.
- Only allocate a stream structure and attach it to a socket in
streamsopen(). Previously, if a svr4 program performed a stream
operation on an arbitrary socket not opened via the streams device,
we would attach streams state data to it and change f_ops of the
associated struct file while it was in use. The latter was especially
not safe, and if a program wants a stream object it should open it via
the streams device anyway.
- Don't bother locking so_emuldata in the streams code now that we only
touch it right after creating a socket (in streamsopen()) or when
tearing it down when the file is closed.
- Remove D_NEEDGIANT from the streams device as it is no longer needed.
renegotiation, we only initialize the hardware only when it is
absolutely required. Process SIOCGIFADDR ioctl in em(4) when we know
an IPv4 address is added. Handling SIOCGIFADDR in a driver is
layering violation but it seems that there is no easy way without
rewritting hardware initialization code to reduce settle time after
reset.
This should fix a long standing bug which didn't send ARP packet when
interface address is changed or an alias address is added. Another
effect of this fix is it doesn't need additional delays anymore when
adding an alias address to the interface.
While I'm here add a new if_flags into softc which remembers current
prgroammed interface flags and make use of it when we have to program
promiscuous mode.
Tested by: Atanas <atanas AT asd DOT aplus DOT net>
Analyzed by: rwatson
Discussed with: -stable
- Copy ethernet firmware down in small chunks so as to avoid bugs
in early versions of the bootstrap firmware.
- Attempt to "adopt" the running firmware if we cannot load a suitable
firmware image via firmware(9).
- Separate firmware validation into its own routine, and check the
major/minor driver/firmware ABI version.
instead of doing the first load with the BUS_DMA_NOWAIT flag. On 4.x with
PAE and > 4gb of RAM this proved disastrous if there weren't enough bounce
pages as amr_mapcmd() would return failure but the callback would later
fire once enough bounce pages were available and would then overwrite
another command's S/G list.
MFC after: 3 days
Submitted by: scottl (4.x version)
Reviewed by: scottl (port from 4.x to HEAD)
precedence uart. With my last change, it became a tie, and uart seems
to always win on my amd64. This was not my intention, so have sio be
just a tiny bit more preferred than uart.
Note: I'm not making any judgement on the merits of uart winning. I'm
just saying that if we want to change it, we do it on purpose.
FreeBSD repository and to clean up the license header so as to
not pollute the license with file function.
Zero all mailbox structures prior to use (just in case). Change
the outgoing mailbox count for INIT_FIRMWARE to be correct.
from a semantic point of view, but I notified the author of the driver
for confirmation. So far it at least fixes the build and should only
lead to not identifying or wrongly identifying a soundcard in the worst
case.
mark it as timed out. Don't try and free the config
request for read_cfg_header that times out because
it's still active. Put in code for the config reply
handler that will then free up timed out requests.
Fix the FC_PRIMITIVE_SEND completion to not try
and free a command twice. Dunno how this possibly
could have been working for awhile.
MFC after: 2 weeks
out ELS buffers but *don't* hang out commands,
we hang folks on the SAN because the LSI-Logic
f/w apparently sends back BUSY or QFULL or some
darn thing.
If we add command buffers, we have to respond to
them sensibly even if we don't have any upstream
listeners (scsi_targ or scsi_targ_bh), so put in
some local command reponse stuff.
MFC after: 2 weeks
sound cards with optional pseudo-multichannel playback.
It's based on snd_emu10k1 sound driver. Single channel version is available
from audio/emu10kx port since some time.
The two new ALSA header files (GPLed), which contain Audigy 2 ("p16v") and
Audigy 2 Value ("p17v") specific interfaces, are latest versions from ALSA
Mercurial repository.
This is not connected to the build yet.
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
latest version from Mercurial repository. It brings definition of some
additional Audigy 2 / Audigy 2 Value registers.
- Use new #defines from ALSA emu10k1.h
- Remove unused include files:
+ emu10k1-ac97.h was imported from ALSA and never used,
+ emu10k1.h was imported from Creative Linux emu10k1 driver, but only
AUDIGY_CODEBASE was used from it.
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
forcing all transfers to do the start read/write stop by hand. Some
smart bridges prefer this sort of operation, and this allows us to
support their features more easily. When bridges don't support it, we
fall back to using the old-style opertaions. Expand the ioctl
interface to expose this function. Unlike the old-style interface,
this interface is thread safe, even on old bridges.
Add MEMORY_BARRIER for the few scratch dma ops that were missing
them plus add a couple of hi 32 bit dma ops (we could probably
allow 64 bit scratch and request/response queue dma now).
install custom pager functions didn't actually happen in practice (they
all just used the simple pager and passed in a local quit pointer). So,
just hardcode the simple pager as the only pager and make it set a global
db_pager_quit flag that db commands can check when the user hits 'q' (or a
suitable variant) at the pager prompt. Also, now that it's easy to do so,
enable paging by default for all ddb commands. Any command that wishes to
honor the quit flag can do so by checking db_pager_quit. Note that the
pager can also be effectively disabled by setting $lines to 0.
Other fixes:
- 'show idt' on i386 and pc98 now actually checks the quit flag and
terminates early.
- 'show intr' now actually checks the quit flag and terminates early.
actually go write the config page. This fixes the long standing
problem about updating NVRAM on Fibre Channel cards and seems
so far to not break SPI config page writes.
Put back role setting into mpt. That is, you can set a desired role
for mpt as a hint. On the next reboot, it'll pick that up and redo
the NVRAM settings appropriately and warn you that this won't take
effect until the next reboot. This saves people the step of having
to find a BIOS utilities disk to set target and/or initiator role
for the MPT cards.
significantly reduces booting time when there is broken floppy disk drive,
controller, cable, BIOS, etc.
When the floppy controller interface is correctly implemented, disk change
signal (DSKCHG) is reflected in the Digital Input Register (DIR) at 0x3f7.
However, there are many cases that the signal is unusable. Moreover, some
BIOS does not reserve the port at all. In those cases, the register may not
function.
loading for the QLogic cards.
Because isp(4) exists before the root is mounted, it's not really
possible for us to use the kernel's linker to load modules directly
from disk- that's really too bad.
However, the this is still a net win in in that the firmware has
been split up on a per chip (and in some cases, functionality)
basis, so the amount of stuff loaded *can* be substantially less
than the 1.5MB of firmware images that ispfw now manages. That is,
each specific f/w set is now also built as a module. For example,
QLogic 2322 f/w is built as isp_2322.ko and Initiator/Target 1080
firmware is built as isp_1080_it.ko.
For compatibility purposes (i.e., to perturb folks the least), we
also still build all of the firmware as one ispfw.ko module.
This allows us to let 'ispfw_LOAD' keep on working in existing
loader.conf files. If you now want to strip this down to just
the firmware for your h/w, you can then change loader.conf to
load the f/w you specifically want.
We also still allow for ispfw to be statically built (e.g., for
PAE and sparc64).
Future changes will look at f/w unloading and also role switching
that then uses the kernel linker to load different ips f/w sets.
MFC after: 2 months
Use it to reset controller and to select data rate. According to Intel
80277AA datasheet, software reset behaves the same as DOR reset except
that it is self clearing. National Semiconductor PC8477B datasheet says
the same. As a side effect, we no longer use Configuration Control
Register (CCR) at 0x3f7 for these controllers, which is often missing
in modern hardware.
(and by extension, the 2422).
One peculiar thing I've found with the 2322 is that if you
don't force it to do Hard LoopID acquisition, the firmware
crashes. This took a while to figure out.
While we're at it, fix various bugs having to do with NVRAM
reading and option setting with respect to pieces of NVRAM.
is never taken since there aren't any 802.11a ural(4) sticks available
on the market.
PR: kern/99676
Submitted by: KIYOHARA Takashi
Reviewed by: damien
MFC after: 1 week
tree... John Baldwin noted that sio might pass values between probe
and attach via softc. It appears that sio does leave the hardware in
a known state after probing, so other drivers that try to probe might
leave it in a worse state. It doesn't seem to pass any data in softc,
however, that I could find... I think we should not be probing for
anything but nonPnP isa, but that's a change for another day.
Submitted by: Frank Behrens
PR: 87845
cards: the chips are all marked "RTL8111B", but they put stickers on the
back that say "RTL8168B/8111B". The manual says there's only one HWREV code
for both the 8111B and 8168B devices, which is 0x30000000, but the cards
they sent me actually report HWREV of 0x38000000. Deciding to trust the
hardware in front of me rather than a possibly incorrect manual (it wouldn't
be the first time the HWREVs were incorrectly documented), I changed the
8168 revision code. It turns out this was a mistake though: 0x30000000
really is a valid for the 8168.
There are two possible reasons for there to be two different HWREVs:
1) 0x30000000 is used only for the 8168B and 0x38000000 is only for
the 8111B.
2) There were 8111/8168 rev A devices which both used code 0x30000000,
and the 8111B/8168B both use 0x38000000.
The product list on the RealTek website doesn't mention the existence of
any 8168/8111 rev A chips being in production though, and I've never seen
one, so until I get clarification from RealTek, I'm going to assume that
0x30000000 is just for the 8168B and 0x38000000 is for the 8111B only.
So, the HWREV code for the 8168 has been put back to 0x30000000,
a new 8111 HWREV code has been added, and there are now separate
entries for recognizing both devices in the device list. This will
allow all devices to work, though if it turns out I'm wrong I may
need to change the ID strings
BCM5787 based NICs.
- Recognize BCM5703 B0 ASIC.
- Rewrite the jumbo capability matching macro, so that chips known
to work are listed there. [*]
[*] I'm still not sure about this. Probably more corrections
will be done to this macro after discussion with davidch@
and brad@OpenBSD.
Obtained from: OpenBSD (brad)
This driver was ported from OpenBSD by Shigeaki Tagashira
<shigeaki@se.hiroshima-u.ac.jp> and posted at
http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html
It was additionally cleaned up by me.
It is still a work-in-progress and thus is purposefully not in GENERIC.
And it conflicts with nve(4), so only one should be loaded.
latter is a PCIe 10/100 chip.
Finally fix the EEPROM reading code so that we can access the EEPROMs on all
devices. In order to access the EEPROM, we must select 'EEPROM programming'
mode, and then set the EEPROM chip select bit. Previously, we were setting
both bits simultaneously, which doesn't work: they must be set in the
right sequence.
Always obtain the station address from the EEPROM, now that EEPROM
reading works correctly.
Make the TX interrupt moderation code based on the internal timer
optional and turned off by default.
Make the re_diag() routine conditional and off by default. When it is
on, only use it for the original 8169, which was the only device that
that really needed it.
Modify interrupt handling to use a fast interrupt handler and fast
taskqeueue.
Correct the rgephy driver so that it only applies the DSP fixup for
PHY revs 0 and 1. Later chips are fixed and don't need the fixup.
Make the rgephy driver advertise both 1000_FD and 1000_HD bits in
autoneg mode. A couple of the devices don't autoneg correctly unless
configured this way.
stations in power save: add a new q where mcast frames are stashed
and on beacon update (at DTIM) move frames from the mcast q to the
cabq and start it. This ensures the cabq is only manipulated in
one place.
Sponsored by: Hobnob
MFC after: 2 weeks
Don't enable/disable I/O space except for SAS adapters.
This fixes a problem with VMware 4.5 Workstation.
Fix an egregious bug introduced to target mode so it actually
will not panic when you first enable a lun.
Minor fixes:
Take more infor from port facts and configuration pages.
MFC after: 1 week
- Add a new function linker_release_module() as a more intuitive complement
to linker_reference_module() that wraps linker_file_unload().
linker_release_module() can either take the module name and version info
passed to linker_reference_module() or it can accept the linker file
object returned by linker_reference_module().
- Curitel PC5740 Wireless Modem (Verizon's PCMCIA card)
- Sierra MC5720 Wireless Modem (Built in to Thinkpad X60s)
The scanner in the PR is already supported.
PR: 98908
Submitted by: Michael Collette <metrol@metrol.net>
blinks by default. When the operating system (read: normally an Xbox
360) initializes the gamepad, the LED stops blinking.
Change our uhid code to do the same.
PR: 97169
Submitted by: Ed Schouten <ed@fxq.nl>
- Enable 4 automatic vchan's by default.
- Add some comments which provide ides/questions for improvement.
- Prefix some temporary sysctl's with an underscore to denote that it is not
an official API but a workaround until the real solution is implemented.
yet. More commits to follow.
I got no response from the author, but since the driver is BSD licensed
I don't think he will complain. :-)
I got it from http://people.freebsd.org/~lofi/envy24.tar.gz
Written by: Katsurajima Naoto <raven@katsurajima.seya.yokohama.jp>
- Add more device IDs, ASIC revisions and chip IDs.
- Rewrite a bit code that picks the description for device.
- Introduce several macros to shorten quirks for bugs and
features.[*]
- Use some magic values, that OpenBSD has successfully
possessed from Linux (Broadcom supplied) driver.
- Remove disabled code that tried to access VPD.
[*] The macro that matches Jumbo capable NICs is
rewritten to preserve our current behavior. I
need clarify whether our or theirs is correct.
PR: 68351 (and may be others)
Obtained from: OpenBSD, brad@ mostly
!IFQ_DRV_IS_EMPTY(). Taking this into account, I re-structured the
transmit routine so as to avoid adding another if/then in the
critical path.
Thanks to brueffer for showing my how to test with altq/pf.
- Update the firmware to the latest released firmware
(1.4.3), which corresponds to the firmware in the
latest shipping drivers from Myricom. This firmware
fixes several bugs in the firmware's PCI-e implementation,
and it also changes the driver/firmware interface:
o TSO was added, and changed the format of the transmit
descriptors.
o The firmware no longer counts transmits descriptors,
but frames. So the driver needs to keep a count
of the number of frames sent.
o The weird interrupt strategy changed to a normal receive
return ring. This ring is much bigger, and we may be
able to support DEVICE_POLLING.
o Myricom's header files changed the name of firmware
related #define's and enums (s/_MCP_/FW_).
- Stopped spamming the console with lots of printfs unless
mxge_verbose (or bootverbose) is set.
- Made additional information available via sysctl, including
the results of a PCI-e DMA benchmark run at device reset.
- Decreased the excessively long timeouts when sending commands
from 2 seconds to 20ms.
Sponsored by: Myricom Inc.
the description so we don't have to do any more queries. Disable the
event query code until it figured out since but it is similar to the
AEN detail so we should be able to get that working.
s/myri10ge/mxge/g replacement in the myri10ge files. A few contuation
lines were joined because of the regained columns.
- Hook the mxge driver back to the build.
o Implement a bunch of sysctl's to report the information
that's now always reported. Mvoe reporting of that info
to bootverbose, but maybe it can go away entirely.
dev.ed.X.type: string name
dev.ed.X.TxMem: amount of memory used for tx side of the card
dev.ed.X.RxMem: amount of memory used for rx side of the card
dev.ed.X.Mem: Total amount of mem on card.
o Better comments about where NE-2000 (and clones) gets their MAC
address from.
systems. Introduce a new sysctl "hw.acpi.disable_on_reboot" that allows
users to re-enable the old behavior in case it's needed for some systems.
We never disable in the power-off path.
Original approach submitted by Alexander Logvinov <abuse@akavia.ru> with
reworking by Jung-uk Kim and myself.
firmware_get() will not work while resuming. Note that we can't
simply drop the FIRMWARE_UNLOAD flag, because that will result in
a firmware image that can never be unloaded by the user since the
firmware subsystem will hold a linker reference to it (it's not
clear that firmware_put() without FIRMWARE_UNLOAD ever does quite
what you'd want).
- Removed updates to if_ibytes, if_obytes, if_imcasts, and if_omcasts.
These should not be handled by the driver.
- Add code to handle excessively fragmented mbufs when mapping TX frames.
Reviewed by: ps
Approved by: ps (mentor)
MFC after: 1 week
SK-NET GENESIS document says reading SK_ISSR should stop generating
further interrupts(Since we drop a driver lock before invoking
ifp->if_input handler we should disable interrupts in ISR in order
to protect integrity of softc from subsequent interrupts). But it
seems that there is possibility of loosing interrupts between
reading SK_ISSR and determining which interrupts are reported.
To cope with the situation we continuously read SK_ISSR register
until there are no interrupts. However, it seems that the above
work around doesn't fix all cases. To protect watchdog handler
from triggering false alarm add a work around code which try to
reclaim pending Tx descriptors before resetting hardware. This
should fix occasional watchdog timeout errors seen on this driver.
Reported by: Frank Behrens <frank AT pinky dot sax dot de >
Tested by: Frank Behrens <frank AT pinky dot sax dot de >
taskqueued interrupt mode is going to be quite complex. Since
the polling mode is considered legacy feature for em(4) driver,
the decision is made to make polling and new interrupt handler
mutually exclusive, selected at compile time.
If kernel is compiled with DEVICE_POLLING, the fast taskqueued
interrupt handler code is disabled and the em_poll() and legacy
em_intr() functions are enabled. Otherwise, legacy functions
are disabled and only em_intr_fast() code is compiled.
Discussed with: scottl
Clean out the abortive start to homegrown, per-mpt,
Domain Validation. This should really be done at a
higher level.
Use the PIM_SEQSCAN flag for U320- this seems to correct
cases of being unable to consistently negotiate U320 in
the cases where I'd seen this before.
Between this and other recent checkins, this driver is
pretty close to being ready for MFC.
Reviewed by: scottl, ken, scsi@
MFC after: 1 week
set to ILACC rather than PCnet-PCI as VMware doesn't implement ILACC
compatibility, resulting in the VMware virtual machine to crash if
enabled. Add a comment regarding usage of ILACC vs. PCnet-PCI mode.
Reported and tested by: gnn, wsalamon
device went away while open or if you tried to change the config
number while devices were open. Based on the patch from the PR with
a number of changes as discussed with the submitter.
PR: usb/97271
Submitted by: Anish Mistry
axe_cmd() calls. Without this the device can get confused if multiple
threads attempt these operations concurrently. The problem was
easily reproducible by running "ifconfig axe0" in a loop because
eventually it would conflict with axe_tick_task().
A similar approach is probably required in all USB ethernet drivers.
Move the code for printing timer statistics into a test function instead of
an ifdef (accessible via the debug.acpi.hpet_test tunable). Also use defines
for register offsets instead of magic values.
Courtesy of: slow flight to HK
it. We just moved it to be pci specific, so this was causing compile
problems (linking problems, so I didn't notice since I unwisely just
built the module).
vendor-specific device ids across vendors.
- Include the revision in the dc_devs[] array instead of special casing
the revid handling in dc_devtype().
- Use PCI bus accessors to read registers instead of pci_read_config()
where possible.
- Use an 8-bit write to update the latency timer.
- Use PCIR_xxx constants and remove unused DC_xxx related to standard
PCI config registers.
MFC after: 1 week
(1) bpf peer attaches to interface netif0
(2) Packet is received by netif0
(3) ifp->if_bpf pointer is checked and handed off to bpf
(4) bpf peer detaches from netif0 resulting in ifp->if_bpf being
initialized to NULL.
(5) ifp->if_bpf is dereferenced by bpf machinery
(6) Kaboom
This race condition likely explains the various different kernel panics
reported around sending SIGINT to tcpdump or dhclient processes. But really
this race can result in kernel panics anywhere you have frequent bpf attach
and detach operations with high packet per second load.
Summary of changes:
- Remove the bpf interface's "driverp" member
- When we attach bpf interfaces, we now set the ifp->if_bpf member to the
bpf interface structure. Once this is done, ifp->if_bpf should never be
NULL. [1]
- Introduce bpf_peers_present function, an inline operation which will do
a lockless read bpf peer list associated with the interface. It should
be noted that the bpf code will pickup the bpf_interface lock before adding
or removing bpf peers. This should serialize the access to the bpf descriptor
list, removing the race.
- Expose the bpf_if structure in bpf.h so that the bpf_peers_present function
can use it. This also removes the struct bpf_if; hack that was there.
- Adjust all consumers of the raw if_bpf structure to use bpf_peers_present
Now what happens is:
(1) Packet is received by netif0
(2) Check to see if bpf descriptor list is empty
(3) Pickup the bpf interface lock
(4) Hand packet off to process
From the attach/detach side:
(1) Pickup the bpf interface lock
(2) Add/remove from bpf descriptor list
Now that we are storing the bpf interface structure with the ifnet, there is
is no need to walk the bpf interface list to locate the correct bpf interface.
We now simply look up the interface, and initialize the pointer. This has a
nice side effect of changing a bpf interface attach operation from O(N) (where
N is the number of bpf interfaces), to O(1).
[1] From now on, we can no longer check ifp->if_bpf to tell us whether or
not we have any bpf peers that might be interested in receiving packets.
In collaboration with: sam@
MFC after: 1 month
fixing speed negotiation.
Also fix the mpt_execute_req function to actually
match mpt_execute_req_a64. This may explain why
i386 users were having more grief.
can see the results of SPI negotiation w/o being overwhelmed
with other crap).
+ For U320 devices, check against both Settings *and* DV flags before
deciding whether we need to skip actual SPI settings for a device.
+ Go back to creating a 'physical disk' side of a raid/passthru bus that
is limited to the number of maximum physical disks. Actually, this isn't
probably *quite* right yet for one RAID volume, and if we ever end up
with finding a device that supports more than one RAID volume (not likely),
it probably won't quite be right either.
The problem here is that the creating of this 'physical' passthru sim is
just a cheap way to leverage off the CAM midlayer to do our negotiation
for us on the subentities that make up a RAID volume. It almost causes
more trouble than it is worth because we have to remember which side
we're talking to in terms of forming commands and which target ids are
real and so on. Bleah.
+ Skip trying to actually do SPI settings for the RAID volumes on the
real side of the raid/passthru bus pair- this just confuses the issue.
The underlying real physical devices will have the negotiation performed
and the Raid volume will inherit the resultant settings. At the sime time,
non-RAID devices can be on the same real bus, so *do* perform negotiations
with them.
+ At the end of doing all of the settings twiddling, *ahem*, remember to
go update the settings on the card itself (dunno how this got nuked).
At this point, negotiations *seem* to be being done (again) correctly for
both RAID volumes and their subentities. And they seem to be *mostly*
now right for other non-RAID entities on the same bus (I ended up with
3 out of 8 other disks still at narror/async- haven't the slightest
idea why yes).
Finally, negotiations on a normal bus seem to work (again).
There's still more work coming into this area, but we're in the
final stretch.
the passed target id is one of the RAID VolumeID. This result
is used to decide whether to try and do actual SPI negotiations
on the real side of the raid/passthru bus pair. The reason we
check this is that we can have both RAID volumes and real devices
on the same bus.
USBD_FORCE_SHORT_XFER to ensure that we actually build and execute
a transfer. This means that the various alloc_sqtd_chain functions
will always construct a transfer, so it is safe to modify the
allocated descriptors on return. Previously there were cases where
a zero length transfer would cause a NULL dereference.
Reported by: bp
- Reduce the number of RX and TX buffers bfe uses so that it does not use more
bounce buffers than busdma is willing to allow it to use
See if_bfe.c for comments on why this is now safe to do.
Also use BUS_DMA_ALLOCNOW to be on the safe side.
2. Look for the Descriptor Error, and Descriptor Protocol Error flags from
the card, and down the interface if we detect either.
#1 (along with fixes to busdma) makes sure that this card works in all
memory situations. Prior to this change, it was just luck that 512 count
RX/TX lists were properly aligned. Now we can use any size of RX/TX lists
and still have them properly aligned.
#2 ensures that we don't get into an endless interrupt storm if busdma fails
us. Descriptor Protocol Error would occur if we misaligned the TX/RX rings,
and Descriptor Error would occur if we tried to give the card descriptors
or rings with addresses > 1G. Trying to reinitialize the card isn't going
to fix these errors, hence we don't try.
host controllers to avoid the need to allocate any multi-page
physically contiguous memory blocks. This makes it possible to use
USB devices reliably on low-memory systems or when memory is too
fragmented for contiguous allocations to succeed.
The USB subsystem now uses bus_dmamap_load() directly on the buffers
supplied by USB peripheral drivers, so this also avoids having to
copy data back and forth before and after transfers. The ehci and
ohci controllers support scatter/gather as long as the buffer is
contiguous in the virtual address space. For uhci the hardware
cannot handle a physical address discontinuity within a USB packet,
so it is necessary to copy small memory fragments at times.
lost one set to a peninsula power failure last night. After
this, I can see both submembers and the raid volumes again,
but speed negotiation is still broken.
Add a mpt_raid_free_mem function to centralize the resource
reclaim and fixed a small memory leak.
Remove restriction on number of targets for systems with IM enabled-
you can have setups that have both IM volumes as well as other devices.
Fix target id selection for passthru and nonpastrhu cases.
Move complete command dumpt to MPT_PRT_DEBUG1 level so that just
setting debug level gets mostly informative albeit less verbose
dumping.
but large parts are rewritten by matk and tanimura.
This is old code, it's not maintained since 2003. We also don't have a
maintainer for this! Yuriy Tsibizov took it and uses it in his emu10kx
driver. Since the emu10kx driver will enter the tree "soon" (some bugs
have to be fixed after Yuriy return from his holidays), I add it here
already.
This also contains some changes to emu10k1 and cmi, so if you're lucky,
you can now make some kind of use of midi with those soundcards.
To all those poor souls which don't have such a card: feel free to send
patches, we don't have a maintainer for this.
To those which miss a specific feature in the midi code: feel free to
submit patches, we don't have a maintainer for this.
Oh, did I already told that it would be nice if someone would take care
of it? Maintainer with midi equipment wanted! :-)
If you get LOR's, submit a PR and notify multimedia@ please. If you get
panics, submit a PR with a backtrace (compile the sound system into your
kernel instead of using modules in this case) and notify multimedia@
please.
Written by: matk, tanimura
Submitted by: "Yuriy Tsibizov" <Yuriy.Tsibizov@gfk.ru>
Based upon: code from NetBSD
but large parts are rewritten by matk and tanimura.
This is old code, it's not maintained since 2003. We also don't have a
maintainer for this! Yuriy Tsibizov took it and uses it in his emu10kx
driver. Since the emu10kx driver will enter the tree "soon" (some bugs
have to be fixed after Yuriy return from his holidays), I add it here
already.
This also contains some changes to emu10k1 and cmi, so if you're lucky,
you can now make some kind of use of midi with those soundcards.
To all those poor souls which don't have such a card: feel free to send
patches, we don't have a maintainer for this.
To those which miss a specific feature in the midi code: feel free to
submit patches, we don't have a maintainer for this.
Oh, did I already told that it would be nice if someone would take care
of it? Maintainer with midi equipment wanted! :-)
If you get LOR's, submit a PR and notify multimedia@ please. If you get
panics, submit a PR with a backtrace (compile the sound system into your
kernel instead of using modules in this case) and notify multimedia@
please.
Written by: matk, tanimura
Submitted by: "Yuriy Tsibizov" <Yuriy.Tsibizov@gfk.ru>
Based upon: code from NetBSD
This used to make syscons switch to vty0 when we entered DDB but this
was lost in the KDB shuffle. We may want to bring it back down the road
but it should be done by calling cn_init_t/cn_term_t instead, possibly
with a flag argument saying "Debugger!"
other timeouts could not happen while suspending, including timeouts
for things like msleep. This caused the system to hang on suspend
when the cbb was enabled, since its suspend path powered down the
socket which used a timeout to wait for it to be done.
APM now creates a thread when it is enabled, and deletes the thread
when it is disabled. This thread takes the place of the timeout by
doing its polling every ~.9s. When the thread is disabled, it will
wakeup early, otherwise it times out and polls the varius things the
old timeout polled (APM events, suspend delays, etc).
This makes my Sony VAIO 505TS suspend/resume correctly when APM is
enabled (ACPI is black listed on my 505TS).
This will likely fix other problems with the suspend path where
drivers would sleep with msleep and/or do other timeouts. Maybe
there's some special case code that would use DELAY while suspending
and msleep otherwise that can be revisited and removed.
This was also tested by glebius@, who pointed out that in the patch I
sent him, I'd forgotten apm_saver.c
MFC After: 3 weeks
was done, I believe, to work around some cards having issues in the
suspend case. I think that this helped my Sony VAIO TS505 work better
when it had certain wireless cards in it and I did a apm -z. I've not
tested suspend/resume on other laptops in a long time, so I hope this
doesn't cause greif. Please let me know if it does.
of cases where we didn't take out the lock before setting or clearing
a bit. This apparently can lead to a race at kldunload time (at least
on my Turion64 laptop, never saw it on my Sony Vaio).
EHCI spec for linking in new qTDs into an asynchronous QH. This
requires that there is a qTD marked as not active and not halted
at the start of the QH's list, and the hardware will know to re-fetch
the qTD on each pass rather than just looking at the overlay qTD:
"The host controller must be able to advance the queue from the
Fetch QH state in order to avoid all hardware/software race
conditions. This simple mechanism allows software to simply link
qTDs to the queue head and activate them, then the host controller
will always find them if/when they are reachable."
This is achieved by keeping an "inactivesqtd" entry on the QH list,
and re-using it each time as the start of the next transfer, and
allocating a new qTD to become the next inactivesqtd. Then a new
transfer can be activated by just setting its "active" flag, which
avoids all the previous messing with overlay qTD state in
ehci_set_qh_qtd().
before starting exploring (4 seconds), and extend the wait period
if new USB buses are attached while waiting.
This works around a problem seen when there is more than one EHCI
controller in the system and you kldload usb.ko after the system
has booted. The problem is that usb.ko contains 3 separate PCI
drivers which get initialised one by one (uhci, ohci, ehci), and
when each driver is initialised, all PCI buses are re-probed after
just the addition of that driver. This means that there can be a
significant delay between the attaching of a companion controller
and the subsequent EHCI attach, so it is possible for the companion
controller's USB 1.x bus to be scanned before the EHCI driver gets
a chance to check if there is really a USB 2.x device connected.
- Rename REG_DL to REG_DLL and REG_DLH.
- Always treat DLL and DLH as two separate 8-bit registers instead of one
16-bit register.
Additionally, remove the probe for the high 4 bits of IER being 0 and don't
assume we can always read/write 0 to/from those bits.
These changes allow uart(4) to drive the UARTs on the Intel XScale PXA255.
Reviewed by: marcel
- Skip PnP devices as some wedge when trying to probe them as C-NET(98)S.
This fix makes le(4) actually work with the C-NET(98)S.
Reviewed by: marius
Tested by: Watanabe Kazuhiro < CQG00620 at nifty dot ne dot jp >
Be cognizant as to whether we're running 2KLogin f/w in target mode and
do the appropriate loopid load based upon that.
Do a first cut (seems to work, at least for amd64) at 64 bit target
mode for fibre channel cards. We could probably also do it for SPI
cards, but that's not supported right now.
- Linux ioctl support, with the other Linux changes MegaCli
will run if you mount linprocfs & linsysfs then set
sysctl compat.linux.osrelease=2.6.12 or similar. This works
on i386. It should work on amd64 but not well tested yet.
StoreLib may or may not work. Remember to kldload mfi_linux.
- Add in AEN (Async Event Notification) support so we can
get messages from the firmware when something happens.
Not all messages are in defined in event detail. Use
event_log to try to figure out what happened.
- Try to implement something like SIGIO for StoreLib. Since
mrmonitor doesn't work right I can't fully test it. StoreLib
works best with the rh9 base. In theory mrmonitor isn't
needed due to native driver support of AEN :-)
Now we can configure and monitor the RAID better.
Submitted by: IronPort Systems.
full, kick the binary blob to force it to complete any pending tx
completions.
- In the watchdog routine, only reset the chip if the blob doesn't complete
any pending tx completions rather than requiring it to complete all of
the pending tx completions.
Submitted by: Nathan Whitehorn <nathanw@uchicago.edu>
MFC after: 2 weeks
lnc(4) on PC98 and i386. The ISA front-end supports the same non-PNP
network cards as lnc(4) did and additionally a couple of PNP ones.
Like lnc(4), the C-bus front-end of le(4) only supports C-NET(98)S
and is untested due to lack of such hardware, but given that's it's
based on the respective lnc(4) and not too different from the ISA
front-end it should be highly likely to work.
- Remove the descriptions of le(4), which where converted from lnc(4),
from sys/i386/conf/NOTES and sys/pc98/conf/NOTES as there's a common
one in sys/conf/NOTES.
still should return BUS_PROBE_LOW_PRIORITY instead of BUS_PROBE_DEFAULT
in order to give pcn(4) a chance to attach in case it probes after le(4).
- Rearrange the code related to RX interrupt handling so that ownership of
RX descriptors is immediately returned to the NIC after we have copied
the data of the hardware, allowing the NIC to already reuse the descriptor
while we are processing the data in ifp->if_input(). This results in a
small but measurable increase in RX throughput.
As a side-effect, this moves the workaround for the LANCE revision C bug
to am7900.c (still off by default as I doubt we will actually encounter
such an old chip in a machine running FreeBSD) and the workaround for the
bug in the VMware PCnet-PCI emulation to am79000.c, which is now also
only compiled on i386 (resulting in a small increase in RX throughput on
the other platforms).
- Change the RX interrupt handlers so that the descriptor error bits are
only check once in case there was no error instead of twice (inspired
by the NetBSD pcn(4), which additionally predicts the error branch as
false).
- Fix the debugging output of the RX and TX interrupt handlers; while
looping through the descriptors print info about the currently processed
one instead of always the previously last used one; remove pointless
printing of info about the RX descriptor bits after their values were
reset.
- Create the DMA tags used to allocate the memory for the init block,
descriptors and packet buffers with the alignment the respective NIC
actually requires rather than using PAGE_SIZE unconditionally. This might
as well fix the alignment of the memory as it seems we do not inherit
the alignment constraint from the parent DMA tag.
- For the PCI variants double the number of RX descriptors and buffers
from 8 to 16 as this minimizes the number of RX overflows im seeing with
one NIC-mainboard combination. Nevertheless move reporting of overflows
under debugging as they seem unavoidable with some crappy hardware.
- Set the software style of the PCI variants to ILACC rather than PCnet-PCI
as the former is was am79000.c actually implements. Should not make a
difference for this driver though.
- Fix the driver name part in the MODULE_DEPEND of the PCI front-end for
ether.
- Use different device descriptions for PCnet-Home and PCnet-PCI.
- Fix some 0/NULL confusion in lance_get().
- Use bus_addr_t for sc_addr and bus_size_t for sc_memsize as these are
more appropriate than u_long for these.
- Remove the unused LE_DRIVER_NAME macro.
- Add a comment describing why we are taking the LE_HTOLE* etc approach
instead of using byteorder(9) functions directly.
- Improve some comments and fix some wording.
MFC after: 2 weeks
Current code does not report link loss correctly - when link goes down,
mii_phy_tick() will notice that with up to mii_anegticks delay.
If link goes up during this delay then link flapping will be unnoticed
by driver.
2) mii_phy_add_media(): initialize sc->mii_anegticks for 10/100 media
3) Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE defines instead of hardcoded values.
Approved by: glebius (mentor)
MFC after: 1 month
divisor. This allows us to set the line speed to the maximum
of 1/4 of the device clock.
o Disable the baudrate generator before programming the line
settings, including baudrate, and enable it afterwards.
was not checked at all. There is only one case when sc_clean_up()
can fail, because of wait_scrn_saver_stop(), but it doesn't hurt
to check anyway.
Reviewed by: rodrigc
Found by: Coverity Prevent
If the embedded controller exists before the sysresource devices, for
example, it will be attached first. Instead, let the normal device
order function work as we first desired. [1]
There still remained a problem where we couldn't allocate resources in
acpi0 that were passed up by the sysresource pseudo-devices. These
devices had to probe/attach first to give their resources to acpi, then
acpi would allocate them before probing/attaching other devices. To
work around this, we attach them from acpi_sysres_alloc(). A better
approach would be to implement multi-pass probe/attach in newbus but
that's a much bigger task.
Suggested by: jhb [1]
Hardware from: Centaur Technologies
MFC after: 1 week
to ensure we match the type signature; we cannot assume HAL_BUS_TAG
and HAL_BUS_HANDLE correspond to bus_space_tag_t and bus_space_handle_t
(should probably do this for HAL_SOFTC too but leave that for now)
MFC after: 1 month
- Fix bfe_encap so that it will pass the address of the mbuf back up to its
caller if/when it modifies it, as it does when doing a m_defrag on a mbuf chain.
- Make sure to unload the dmamap for ALL fragments of a packet, not just the first
- Use BUS_DMA_NOWAIT for all bus_dmamap_load calls so that the allocation of the
map is not delayed - this driver is not set up to handle such delays.
- Reduce the number of RX and TX buffers bfe uses so that it does not use more
bounce buffers than busdma is willing to allow it to use
With these changes, the driver now works properly for a user with a 2GB system,
and it also works on my system when the acceptable address range is lowered to 128MB.
Previously, both of these setups would act up after a few minutes of activity.
from the amr_linux. This simplifies the amr_linux shim and puts the
smarts into amr.c.
I tested this with 2 amr controllers in one box. It seems to work
okay with them.
o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
OS dependent layer. Thus, the watchdog timer can go off when the tx
engine is working fine but the OS dependent layer just hasn't been called
to cleanup finished tx transactions. To workaround this, when the watchdog
fires, poke the binary blob to force it to flush any pending tx
completions. If this drops the pending tx count to zero then just return
without logging a message or resetting the chip.
This reportedly fixes the 'device timeout()' errors with at least several
NF4 nve(4) parts.
Submitted by: Nathan Alexander Whitehorn <nathanw@uchicago.edu> (code)
Submitted by: dg (inspiration for comment and explanation)
MFC after: 1 week
POSTWRITE to POSTREAD.
No guarantee that all busdma is usage is perfect, but this change (in
addition to scott's last two commits) makes if_bfe work with > 1GB of
memory in my laptop.
OpenBSD changes. With these changes, PHY part of the driver becomes
functional (it senses media changes and negotiates speed just fine),
previously it just hang with no PHY message, but no data goes through
interface (error message is "can not stop transfer of Tx/Rx descriptor).
Hopefully somebody with more clue/free time will be able to pick up
after me.
Changelog towards if_iwi.c 1.26 (some changes have been committed separately
in the mean time):
- add led support
- add firmware loading on demand
- auto-restart firmware when it crashes
- serialize operations sent to the firmware to reduce firmware crashes
- add power save operation support
- remove incorrect specification of tx power control capability
- add radio on/off switch support
- improve net80211 state machine operation
- recognize and handle beacon miss
- handle authentication and association failures better
- add shared key authentication
- fix ibss mode (many changes)
- fix wme (many changes)
- correct radiotap support (many changes)
- correct bus dma setup of s/g
- correct various locking issues
- fix monitor mode
- fix scanning (many changes)
- recover from wedged scan requests
- respect active channel list
- eliminate cases where interface was marked down on error
- don't treat parity errors as fatal
- reclaim mgt frames immediately from tx queue
- correct interrupt handling, ack early (from NetBSD)
- fix short/long preamble handling
Committed with RELENG_6 compat #if's, should compile in RELENG_6. Requires
net/iwi-firmware-kmod to function.
Much work done by: sam
Tested by: many (freebsd-net), ume, luigi
MFC after: 4 weeks
This driver was generously developed and donated by Highpoint.
It is enabled for i386 only at the moment. I will enable it for amd64
shortly.
Obtained from: HighPoint Technologies, Inc.
- MPSAFE. No more recursive lock required.
- bus_dma(9) conversion. I think it should work on all architectures.
- optimized Rx handler for each normal and jumbo frames. Previously
sk(4) used jumbo frame management code to handle normal sized
frames. As the handler needs an additional lock to protect jumbo
frame management structure from races, it used two lock operations
for each received packet. Now sk(4) uses single lock operation for
normal frame.(Jumbo frame still needs two lock operations as before.)
The hardware supports DMA scatter operations for Rx descriptors such
that it's possible to take advantagee of m_cljget(9) for jumbo frames.
However, due to a unknown reasons it resulted in poor performance on
sparc64. So I dropped m_cljget(9) approach. This should be revisited
since it would reduce one lock operation for jumbo frame handling.
- Tx TCP/Rx IP checksum offload support. According to the data sheet
of SK-NET GENESIS the hardware supports Rx IP/TCP/UDP offload.
But I couldn't make it work on my Yukon hardware. So Rx TCP/UDP was
disabled at the moment. It seems that newer Yukon chips can support
Tx UDP checksum offload too. But I need more documentation first.
- Added more wait time in reading VPD data. It seems that ASUS LOM
takes a very long time to respond VPD read signal.
- Added an additional lock for MII register access callbacks.
- Added more strict received packet validation routine. Previously it
passed corrupted packets to upper layers under certain conditions.
- A new function sk_yukon_tick() to handle auto-negotiation properly.
- Interrupt handler now checks shared interrupt source and protects
the interrupt handler from NULL pointer dereference which was caused
by odd status word value. The status word can returns 0xffffffff if
cable is unplugged while Rx/Tx/auto-negotiation is in progress.
- suspend/resume support(not tested).
- Added Rx/Tx FIFO flush routine for Yukon
- Activate Tx descriptor poll timer in order to protect possible loss
of SK_TXBMU_TX_START command. Previously the driver continuously issued
SK_TXBMU_TX_START when it notices pending Tx descriptors not processed
yet in interrupt handler. That approach would add additional PCI
write access overhead under high Tx load situations and it might fail
if the first SK_TXBMU_TX_START was lost and no interrupt is generated
from the first SK_TXBMU_TX_START command.
- s/printf/if_printf/, s/printf/device_printf/, Axe sk_unit in softc.
- Setting multicast/station address is now safe on strict-alignment
architectures.
- Fix long standing bug in VLAN header length setup.
- Added/corrected register definitions for Yukon.
(Register information from Linux skge driver.)
- Added Rx status definition for Marvell Yukon/XaQti XMAC.
(Rx status register information from Linux skge driver.)
- Update if_oerrors if we encounter watchdog error.
- callout(9) conversion
Special thanks to jkim who let me know RX status differences between
Yukon and XaQti XMAC.
It seems that there is still occasional watchdog timeout error but I
couldn't reproduce it and need more information to analyze it from
users.
Tested by: bz(amd64), me(i386, sparc64), current ML
Frank Behrens frank ! pinky ( sax $ de
Lower the minimum for memory mapped I/O from 32 bytes to 16 bytes.
This fixes bus enumeration on ia64 now that the Diva auxiliary
serial port is attached to.
channel number since we're not ready at the net80211 layer to deal with them;
note this mapping has to match what's done in ieee80211_mhz2ieee
MFC after: 3 days
controller as we use in boot blocks (querying status register until
bit 1 goes off). If that doesn't happed during reasonable period assume
that the hardware doesn't have AT-style keyboard controller. This makes
FreeBSD working almost OOB on MacBook Pro (still there are issues with
putting second CPU core on-line, but since installation CD comes with
UP kernel with this change one should be able to install FreeBSD without
playing tricks with hints). Other legacy-free hardware (e.g. IBM NetVista
S40) should benefit from this as well, but since I don't have any I can't
verify.
It should make no difference on the ordinary i386 hardware (since in
that case that hardware already would be having an issues with A20
routines in boot blocks). I don't know much about AT-style keyboard
controller on other platforms (and don't have dedicated access to one),
therefore, the code is restricted to i386 for now. I suspect that amd64
may need this as well, but I would rather leave this decision to someone
who knows better about the platform(s) in question.
I have tested this change on as many "ordinary i386 boxes" as I can get
my hands on, and it doesn't create any false negatives on hardware with
AT-style keyboard present.
MFC after: 1 month
This allows one to change the behavior of the driver pre-boot.
NOTE: This patch was made for DragonFly BSD by Sepherosa Ziehau.
PR: kern/94833
Submitted by: Devon H. O'Dell
Obtained from: DragonFly
MFC after: 1 month
end for isa(4).
o Add a seperate bus frontend for acpi(4) and allow ISA DMA for
it when ISA is configured in the kernel. This allows acpi(4)
attachments in non-ISA configurations, as is possible for ia64.
o Add a seperate bus frontend for pci(4) and detect known single
port parallel cards.
o Merge PC98 specific changes under pc98/cbus into the MI driver.
The changes are minor enough for conditional compilation and
in this form invites better abstraction.
o Have ppc(4) usabled on all platforms, now that ISA specifics
are untangled enough.
A slight difference of this chip from its previous siblings is that
it need a gentle "wake up" on every (full) DMA buffer completion to
avoid stalled interrupt handler.
Thanks to George Hartzell for permission on doing remote debugging.
Prime MFC candidate for 6.1-RELEASE. Please reply to this commit if
there are any objections (so I won't bug re@), since the changes
are too small and only specific to VT8251.
PR: i386/95949
Tested by: [1] George Hartzel
myself (remotely)
MFC after: 3 days
[1] http://lists.freebsd.org/pipermail/freebsd-multimedia/2006-April/004003.html
Pull in some target mode changes from a private branch.
Pull in some more RELENG_4 compilation changes.
A lot of lines changed, but not much content change yet.
state structure. This field is only for CCBs that are associated with
actions that are occurring on the HBA (i.e., XPT_CONT_IO actions).
This way we also don't get confused when the upstream listener stalls
try and look at a CCB which has already been freed (by CAM).
as pcf_ebus and pcf_isa, they should probably be fixed back to pcf),
and bti2c doesn't exist, bktr has smbus or iicbb as children..
Brought to you by: http://people.FreeBSD.org/~jmg/driver.pdf
if the specified priority is zero. This avoids a race where the calling
thread could read a snapshot of it's current priority, then a different
thread could change the first thread's priority, then the original thread
would call sched_prio() inside msleep() undoing the change made by the
second thread. I used a priority of zero as no thread that calls msleep()
or tsleep() should be specifying a priority of zero anyway.
The various places that passed 'curthread->td_priority' or some variant
as the priority now pass 0.
have not been passed to the h/w yet. This remedies watchdog timeout
of buffered multicast frames in hostap mode.
While here eliminate an extraneous check; ieee80211_beacon_update sets
the tim bit based on ncabq != 0 so there's no reason to check it too.
Noticed by: Christophe Prevotaux
+ Add boatloads of KASSERTs and *really* check out more locking
issues (to catch recursions when we actually go to real locking
in CAM soon). The KASSERTs also caught lots of other issues like
using commands that were put back on free lists, etc.
+ Target mode: role setting is derived directly from port capabilities.
There is no need to set a role any more. Some target mode resources
are allocated early on (ELS), but target command buffer allocation
is deferred until the first lun enable.
+ Fix some breakages I introduced with target mode in that some commands
are *repeating* commands. That is, the reply shows up but the command
isn't really done (we don't free it). We still need to take it off the
pending list because when we resubmit it, bad things then happen.
+ Fix more of the way that timed out commands and bus reset is done. The
actual TMF response code was being ignored.
+ For SPI, honor BIOS settings. This doesn't quite fix the problems we've
seen where we can't seem to (re)negotiate U320 on all drives but avoids
it instead by letting us honor the BIOS settings. I'm sure this is not
quite right and will have to change again soon.
Radeon memmap code, which with a new DDX driver and DRI drivers should fix
long-term stability issues with Radeons. Also adds support for r200's
ATI_fragment_shader, r300 texrect support and texture caching fixes, i915
vblank support and bugfixes, and new PCI IDs.
The real problem was that ioctl handlers needed to call amr_wait_command()
with the list lock held. This not only solves the completion race, it also
prevents bounce buffer corruption that could arise from amr_start() being
called without the proper locks held.
Discussed with: ps
MFC After: 3 days
the completion of the command can occur before tsleep is called and
the command ends up blocking forever since the wakeup has already
been called.
Submitted by: ups
new chips and improves support for already supported ones.
Some details, important for future merges:
- if_em.c merged manually, viewing diff between new vendor
driver and previous one.
- if_em_hw.h dropped in from vendor, and then restored revisions
1.16, 1.17, 1.18.
- if_em_hw.c dropped in from vendor, and then two liner change made,
that restores support for two rare chips.
the NS8250 class driver. The UART has FIFOs if sc_rxfifosz>1, so
test for that instead.
While here properly initialize sc_rxfifosz and sc_txfifosz in the
case the UART doesn't have FIFOs.
There's something strange going on with async events. They seem
to be be treated differently for different Fusion implementations.
Some will really tell you when it's okay to free the request that
started them. Some won't. Very disconcerting.
This is particularily bad when the chip (FC in this case) tells you
in the reply that it's not a continuation reply, which means you
can free the request that its associated with. However, if you do
that, I've found that additional async event replies come back for
that message context after you freed it. Very Bad Things Happen.
Put in a reply register debounce. Warn about out of range context
indices. Use more MPILIB defines where possible. Replace bzero with
memset. Add tons more KASSERTS. Do a *lot* more request free list
auditting and serial number usages. Get rid of the warning about
the short IOC Facts Reply. Go back to 16 bits of context index.
Do a lot more target state auditting as well. Make a tag out
of not only the ioindex but the request index as well and worry
less about keeping a full serial number.
a different register shift and is fed by a different clock than
we use for UltraSPARC hardware. To deal with this, the regshft and
rclk fields in the class structure are removed and bus frontends
now pass the right regshft and rclk to the probe function where
they're put in the BAS and passed in to subordinate drivers.
--------------------
- Seal the fate of long standing memory leak (4 years, 7 months) during
pcm_unregister(). While destroying cdevs, scan / detect possible
children and free its SLIST placeholder properly.
- Optimize channel allocation / numbering even further. Do brute cyclic
checking only if the channel numbering screwed.
- Mega vchan create/destroy cleanup:
o Implement pcm_setvchans() so everybody can use it freely instead
of implementing their own, be it through sysctl or channel auto
allocation.
o Increase vchan creation/destruction resiliency:
+ it's possible to increase/decrease total vchans even during
busy playback/recording. Busy channel will be left alone, untouched.
Abusive test sample:
# play whatever...
#
while : ; do
sysctl hw.snd.pcm0.vchans=1
sysctl hw.snd.pcm0.vchans=10
sysctl hw.snd.pcm0.vchans=100
sysctl hw.snd.pcm0.vchans=200
done
# Play something else, leave above loop running frantically.
+ Seal another 4 years old bug where it is possible to destroy (virtual)
channel even when its cdevs being referenced by other process.
The "First Come First Served" nature of dsp_clone() is the main
culprit of this issue, and usually manifest itself as dangling
channel <-> process association. Ensure that all of its cdevs
are free from being referenced before destroying it (through
ORPHAN_CDEVT() macross).
All these fixes (including previous fixes) will be MFCed, later.
to avoid possible device unregister race (impossible to reproduce, yet
possible).
- Extra sanity check to ensure proper parent channel is being selected.
- Reset parent channel once all of its children gone.
controllers typically have multiple channels and support a number
of serial communications protocols. The scc(4) driver is itself
an umbrella driver that delegates the control over each channel
and mode to a subordinate driver (like uart(4)).
The scc(4) driver supports the Siemens SAB 82532 and the Zilog
Z8530 and replaces puc(4) for these devices.
in the ISR doesn't read the actual socket event register, but instead
reads garbage (usually 0xffffffff, but other times other things).
This totally violates the PCI spec, but happens rarely enough that a
workaround is in order. This adds one test when we have a real
interrupt to service (which is very rare), and doesn't affect the
usualy 'nothing to see here' case at all.
Problem reported by many, but sam@ gave me this workaround after
diagnosing the problem.
some systems were designed so that AML writes to various resources shared
with OS drivers, including the RTC, PIC, PCI, etc. These writes could
collide with writes by the OS and should never be performed. For now, we
print a message if such an access occurs, but do not block it. To block
the access, the tunable "debug.acpi.block_bad_io" can be set to 1. In the
future, we will flip the switch and this will become the default.
Information about this problem was found in Microsoft KB 283649. They
block IO accesses if the BIOS indicates via _OSI that it is Windows 2001
or higher. They always block accesses to the PIC, cascaded PIC, and ELCRs,
no matter how old the BIOS.
systems (blade servers). On most systems, this is implemented as an IO
write to the SMI port and the BIOS generates the actual reset.
PR: kern/94939
Submitted by: dodell@ixsystems.com
Reviewed by: jhb
MFC after: 3 weeks
Saab for helping to track this down. Fix a error with 32bit DMA size
calculation that seemed to be harmless. Add a few micro-optimizations while
I'm here.
mddestroy() only if the file is from a non-MPSAFE VFS.
- No longer unconditionally hold Giant in the md kthread for vnode-backed
kthreads.
- Improve the handling of the thread exit race when destroying an md
device.
a problem with listing large number of md(4) devices. Either 'list' or
'query' mode uses XML.
Additionally, new functionality was introduced. It's possible to pass
multiple devices to -u:
# ./mdconfig -l -u md0,md1
Approved by: cognet (mentor)
Kernel changes:
Inform hwpmc of executable objects brought into the system by
kldload() and mmap(), and of their removal by kldunload() and
munmap(). A helper function linker_hwpmc_list_objects() has been
added to "sys/kern/kern_linker.c" and is used by hwpmc to retrieve
the list of currently loaded kernel modules.
The unused `MAPPINGCHANGE' event has been deprecated in favour
of separate `MAP_IN' and `MAP_OUT' events; this change reduces
space wastage in the log.
Bump the hwpmc's ABI version to "2.0.00". Teach hwpmc(4) to
handle the map change callbacks.
Change the default per-cpu sample buffer size to hold
32 samples (up from 16).
Increment __FreeBSD_version.
libpmc(3) changes:
Update libpmc(3) to deal with the new events in the log file; bring
the pmclog(3) manual page in sync with the code.
pmcstat(8) changes:
Introduce new options to pmcstat(8): "-r" (root fs path), "-M"
(mapfile name), "-q"/"-v" (verbosity control). Option "-k" now
takes a kernel directory as its argument but will also work with
the older invocation syntax.
Rework string handling in pmcstat(8) to use an opaque type for
interned strings. Clean up ELF parsing code and add support for
tracking dynamic object mappings reported by a v2.0.00 hwpmc(4).
Report statistics at the end of a log conversion run depending
on the requested verbosity level.
Reviewed by: jhb, dds (kernel parts of an earlier patch)
Tested by: gallatin (earlier patch)
the error on sparc64 hadn't changed since the last checkin, pass
LINT on other platforms and mpt doesn't work on sparc64 anyway
and the tinderbox build didn't work for me in a cross build case
on my main build machine (which runs RELENG_6). Sigh. Still
need to try harder.
A) Fibre Channel Target Mode support mostly works
(SAS/SPI won't be too far behind). I'd say that
this probably works just about as well as isp(4)
does right now. Still, it and isp(4) and the whole
target mode stack need a bit of tightening.
B) The startup sequence has been changed so that
after all attaches are done, a set of enable functions
are called. The idea here is that the attaches do
whatever needs to be done *prior* to a port being
enabled and the enables do what need to be done for
enabling stuff for a port after it's been enabled.
This means that we also have events handled by their
proper handlers as we start up.
C) Conditional code that means that this driver goes
back all the way to RELENG_4 in terms of support.
D) Quite a lot of little nitty bug fixes- some discovered
by doing RELENG_4 support. We've been living under Giant
*waaaayyyyy* too long and it's made some of us (me) sloppy.
E) Some shutdown hook stuff that makes sure we don't blow
up during a reboot (like by the arrival of a new command
from an initiator).
There's been some testing and LINT checking, but not as
complete as would be liked. Regression testing with Fusion
RAID instances has not been possible. Caveat Emptor.
Sponsored by: LSI-Logic.
is derived from the phrase 'MegaRAID Firmware Interface' used by LSI. This
driver provides a block interface to logical disks on the card and a minimal
management device. It is MPSAFE, INTR_FAST, and 64-bit capable.
Thanks to Dell for providing hardware to test with and IronPort for
sponsoring the work.
Sponsored by: Dell, Ironport
MFC After: 3 days
socket also supports the voltage. Some XV cards have appeared on the
scene (or cards that report they support XV), and in older machines
that have sockets that do not support XV, we were bogusly trying to
power them at XV rather than at 3.3V. Now, power up the card at the
lowest voltage supported by both the card and the socket.
MFC After: 3 days
- [1] Make the driver friendly towards kernel without PREEMPTION.
Use msleep(9) instead of simple unlock-check_variable-lock mechanisme
since the later not really effective in non-preemptible kernel
(especially during codec detection routine).
- Free most driver resources in a sane manner to avoid possible
double free and panics especially during device detach and codec
detection failure.
MFC after: 3 days
[1] http://lists.freebsd.org/pipermail/freebsd-questions/2006-March/116515.html
that have the specified kind, instead of assuming that there is
only one report of the right kind in the report descriptor.
Submitted by: Morten Johansen
Obtained from: NetBSD (indirectly)
PR: usb/77604
o don't send management frames if the IFF_DRV_RUNNING flag is not set.
this prevents the timeout watchdog from being potentially re-armed
when the interface is brought down.
fixes a crash that occurs with RT2661 based adapters.
reported by Arnaud Lacombe.
- Determine open direction using 'flags', not 'mode'. This bug exist since
past 4 years.
- Don't allow opening the same device twice, be it in a same or different
direction.
- O_RDWR is allowed, provided that it is done by a single open (for example
by mixer(8)) and the underlying hardware support true full-duplex operation.
- Do various paranoid checking in case other process/thread trying to hijack
the same device twice (or more).
MFC after: 5 days
transfers. This fixes some cases where the software toggle tracking
was not doing the right thing. For example, a short transfer that
transferred 0 bytes of the requested qTD transfer size does cause
a toggle change, but the existing code was assuming it didn't.
Reported and tested by: pav
MFC after: 2 weeks
debugging message if the flag PMC_F_OLDVALUE was specified in the
PMC_OP_RW request being acted upon. This should fix Coverity bug
CID 671.
Found by: Coverity Prevent
MFC after: 3 weeks
especially for vchans. It turns out that channel numbering always depend
on d->devcount counter (which keep increasing), while PCMMKMINOR() truncate
everything to 8bit length. At some point the truncation cause the newly
created character device overlapped with the existence one, causing erratic
overall system behaviour and panic. Easily reproduce with something like:
(Luckily, only root can reproduce this)
while : ; do
sysctl hw.snd.pcm0.vchans=200
sysctl hw.snd.pcm0.vchans=100
done
- Enforce channel/chardev numbering within 8bit boundary. Return E2BIG
if necessary.
- Traverse d->channels SLIST and try to reclaim "free" counter during channel
creation. Don't rely on d->devcount at all.
- Destroy vchans in reverse order.
Anyway, this is not the fault of vchans. It is just that vchans are so cute
and begging to be abused ;) . Don't blame her.
Old, hidden bugs.. sigh..
MFC after: 3 days
o call firmware_put() early to release the firmware module
o on firmware panics or watchdog timeouts, schedule a task to reinitialize
the interface (we may sleep in iwi_init())
o discard oversized rx frames
flag isn't enough - the filter needs to be set up too, or no multicast frames
are accepted.
Sponsored by: Philips Industrial Applications (indirectly)
MFC after: 3 days
o stop processing interrupts after a firmware fatal error or a radio kill
o clarify the possible values for the 'antenna' sysctl.
o by default, let the firmware do antenna diversity.
the firmware will periodically switch to another antenna to evaluate the
signal quality.
ATA framework. Mainly written to be able to use USB Flash keys.
This is work in progress so use with care :)
Doesn't need CAM and cannot coexist with umass.c
table. Previously, the ddb code knew of each linker set of auxiliary
commands and which explicit command list they were tied to. These changes
add a simple command_table struct that contains both the static list of
commands and the pointers for any auxiliary linker set of additional
commands. This also makes it possible for other arbitrary command tables
to be defined in other parts of the kernel w/o having to edit ddb itself.
The DB_SET macro has also been trimmed down to just creating an entry in
a linker set. A new DB_FUNC macro does what the old DB_SET did which is
to not only add an entry to the linker set but also to include a function
prototype for the function being added. With these changes, it's now also
possible to create aliases for ddb functions using DB_SET() directly if
desired.
generations of 802.11abg chipsets from Ralink Technology.
Get rid of the pccard front-end while I'm here since all adapters are
cardbus ones.
Obtained from: OpenBSD
into a separate module. Accordingly, convert the option into a device
named similarly.
Note for MFC: Perhaps the option should stay in RELENG_6 for POLA reasons.
Suggested by: scottl
Reviewed by: cokane
MFC after: 5 days
to call back for completition and something else is holding the taskqueue
waiting for ATA to return data.
This should clear up the "semaphore timeout !! DANGER Will Robinson !!"
in most situations, and log "taskqueue timeout - completing request directly"
instead, with a delayed "WARNING - freeing taskqueue zombie request" when
the taskqueue finally calls us back with the now stale request.
(It would have been nice if there was a way to remove a scheduled item from
a taskqueue, but that is not currently implemented in the kernel).
A real fix for this is in the works but wont make it to 6.1RELEASE
definite MFC candidate.
- Don't use a common buffer in the softc to store per-command data. Reserve
a buffer in the command itself.
- Don't allocate DMA memory for the kernel command structures when all you
really need is DMA memory for the scratch buffer embedded in them. Instead
allocate a slab for the scratch buffers and divide it up as needed.
- Call bus_dmamap_unload() at the completion of commands.
- Preserve and clear the CAM CCB status flags at completion.
- Reorder some low-level command operations to try to close races.
- Limit the simq to 32 commands for now. There are some serious problems
with the driver under load that are not well understood, so keeping the
simq lower helps avoid this. It has been tested at a higher value, but
this is a safe value that doesn't show much performance degredation.
These changes allow the driver to work reliably with >4GB of memory on i386
and amd64, and also work around deadlocks seen under very high load in
certain situations. The work-around is far from ideal, but without and
documentation it is hard to know what the right fix is.
MFC candidate
By default syscons(4) will look for the kbdmux(4) keyboard first, and then,
if not found, look for any keyboard.
Current kbd code is modified so if kbdmux(4) is the current keyboard, all
new keyboards are automatically added to the kbdmux(4).
Switch to kbdmux(4) can be done at boot time, by loading kbdmux module at
the loader prompt, or at runtime, by kldload'ing the kbdmux module and
releasing current active keyboard.
If, for whatever reason, kbdmux(4) is not required/desired then just do
not load it and everything should work as before. It is also possible to
kldunload kbdmux at runtime and syscons(4) will automatically switch to
the first available keyboard.
No response from: freebsd-current@
MFC after: 1 day
mpt_soft_reset more than once. And to wait for MPT_DB_STATE_READY
twice. I mean, this is crucial- give the IOC a chance to get
ready.
If mpt_reset is called to reinit things, and we succeed, make
sure to re-enable interrupts. This is what has mostly led to
system lockup after having to hard reset the chip. Also, if
we think that interrupts aren't function in mpt_cam_timeout,
for goodness sake, turn them on again.
In read_cfg_header, return distinguishing errnos so the caller
can decide what's an error. It's *not* an error to fail to
read a RAID page from a non-RAID capable device like the FC929X.
Some whitespace fixes (removing spaces from ends of lines).
Developed with: Norbert Koch < NKoch at demig dot de >
No response from: freebsd-current@
Tested by: Norbert Koch < NKoch at demig dot de >
MFC after: 1 day
not hang the system for 5 seconds. If a TMF doesn't complete within,
oh, say 500ms, that's enough.
Put in a printout to catch mpt_recover_commands being activated with
no commands.
*both* SAS and FC, not just SAS.
b) Don't tell the chip we want it to do FIFO signalling if we actually
don't set up the address where the FIFO signal is supposed to be written
(oops).
is closed and then reopened. This appears to be necessary now that
we no longer clear endpoint stalls every time a pipe is opened.
Previously we could assume an initial toggle value of zero because
the clear-stall operation resets the device's toggle state.
Reported by: Holger Kipp
MFC after: 3 days
(atkbd(4)) and PS/2 mouse (psm(4)) are used together.
Turns out that atkbd(4) check_char() method may return "true" while
read_char() method returns NOKEY. When this happens kbdmux(4) was
simply stuck in the dead loop. Avoid dead loop in kbdmux(4) by breaking
out of the loop if read_char() method returns NOKEY.
It almost seems like a bug in atkkbd(4), atkbd_check_char() calls
kbdc_data_ready(), and, the later will return "true" if there are
pending data in either kbd or aux queue. However, because both aux
and kbd are on the same controller, I'm not sure if this is a bug
or feature.
Tested by: markus
MFC after: 1 day
is finished with it; this may only occur when the tx queue is setup as
dba-gated but since the fix is cheap apply it to all queues
while here make the queue depth signed for use in assertions
Reviewed by: apatti
MFC after: 2 weeks
Return BUS_PROBE_LOW_PRIORITY for a successful probe. This is in
preparation of the introduction of scc(4), which is going to handle
SCCs in the near future.
mutex.
- Don't use callout_drain() to stop the toffhandle callout while holding the
fdc mutex (this could deadlock) in functions called from softclock
(callouts aren't allowed to do voluntary sleeps). Instead, use
callout_stop(). Note that since we hold the associated mutex and are now
using callout_init_mtx(), callout_stop() is just as effective as
callout_drain(). (Though callout_drain() is still needed in detach to
make sure softclock isn't contesting on our mutex before we destroy the
mutex.)
- Remove unused callout 'tohandle' from softc.
MFC after: 1 week
interrupt handlers rather than BUS_SETUP_INTR() and BUS_TEARDOWN_INTR().
Uses of the BUS_*() versions in the implementation of foo_intr methods
in bus drivers were not changed. Mostly this just means that some
drivers might start printing diagnostic messages like [FAST] when
appropriate as well as honoring mpsafenet=0.
- Fix two more of the ppbus drivers' identify routines to function
correctly in the mythical case of a machine with more than one ppbus.
processing the interrupt events. If we clear them afterwards we
can completely miss some events as the NIC can change the source
flags while we're in the handler. In order to not get another
interrupt while we're in ifp->if_input() with the driver lock
dropped we now turn off NIC interrupts while in the interrupt
handler. Previously this was meant to be achieved by clearing the
interrupt source flags after processing the interrupt events but
didn't really work as clearing these flags doesn't actually
acknowledge and re-enable the events.
This fixes the device timeouts seen with the VMware LANCE.
- Relax the watchdog timer somewhat; don't enable it until the last
packet is enqueued and if there is a TX interrupt but there are
still outstanding ones reload the timer.
Reported and tested by: Morten Rodal <morten@rodal.no>
MFC after: 3 days
The ed driver on pc98 was broken by if_edvar.h rev1.31.
Reported by: Kaho Toshikazu (kaho at elam kais kyoto-u ac jp)
Tested by: Eiji Kato (ekato at a1 mbn or jp)
MFC after: 3 days
More info regarding these nics can be found at http://www.myri.com.
Please note that the files
sys/dev/myri10ge/{mcp_gen_header.h,myri10ge_mcp.h} are internally
shared between all our drivers (solaris, macosx, windows, linux, etc).
I'd like to keep these files unchanged, so I can just import newer
versions of them when the firmware API/ABI changes. This means I'm
stuck with some of the crazy-long #define names, and possibly
non-style(9) characteristics of these files.
Many thanks to mlaier for doing firmware(9) just as I
needed it, and to scottl for his helpful review.
Reviewed by: scottl, glebius
Sponsored by: Myricom Inc.
forcing DMA alignment to default buffer size.
- Make sure DMA pointer properly aligned to avoid being truncated by caller
which causing severe underruns and random popping (especially in 32bit
playback / recording).
- Add AC97 inverted external amplifier quirk for Maxselect x710s
- http://maxselect.ru/
MFC after: 1 week
the SMI/TCO address space. Switch the bus space I/O to the
one specific for either the SMI or TCO space. Re-calibrate
the tick. Add some more device id's, 82801FBR submitted by des.
This makes it work on the platforms I've tested with.
Go ahead by: des
should fix strange link state behaviour reported for bcm5721 & bcm5704c
2) Clear bge_link flag in bge_stop()
3) Force link state check after bge_ifmedia_upd(). Otherwise we can miss link
event if PHY changes it's state fast enough.
Tested by: phk (bcm5704c)
Approved by: glebius (mentor)
MFC after: 1 week
Acknowledgement should definitly go to JMicron Technology for providing full
docs on the metadata format as the only vendor so far, big thanks from here.
- In em_attach() remove em_check_for_link(). Not needed here, since
already done in em_hardware_init().
- In em_attach() replace the printing block with call to
em_update_link_status().
- Remove modification of sc->link_state from em_hardware_init() and
from em_media_status(). This makes em_update_link_status() a
single point of change. Call em_update_link_status() where needed.
to getting rid u_int for uint and so on).
b) Turn back on 64 bit DAC support. Cheeze it a bit in that we have two
DMA callback functions- one when we have bus_addr_t > 4 bits in width and
the other which should be normal. Even Cheezier in that we turn off setting
up DMA maps to be BUS_SPACE_MAXADDR if we're in ISP_TARGET_MODE. More work
on this in a week or so.
c) Tested under amd64 and 1MB DFLTPHYS, sparc64, i386 (PAE, but insufficient
memory to really test > 4GB). LINT check under amd64.
MFC after: 1 month
automatically both SATA and SAS drives. The async SAS event handling we catch
but ignore at present (so automagic attach/detach isn't hooked up yet).
Do 64 bit PCI support- we can now work on systems with > 4GB of memory.
Do large transfer support- we now can support up to reported chain depth, or
the length of our request area. We simply allocate additional request elements
when we would run out of room for chain lists.
Tested on Ultra320, FC and SAS controllers on AMD64 and i386 platforms.
There were no RAID cards available for me to regression test.
The error recovery for this driver still is pretty bad.
to work with ipmitools. It works with other tools that have an OpenIPMI
driver interface. The port will need to get updated to used this.
I have not implemented the IPMB mode yet so ioctl's for that don't
really do much otherwise it should work like the OpenIPMI version.
The ipmi.h definitions was derived from the ipmitool header file.
The bus attachments are done for smbios and pci/smbios. Differences
in bus probe order for modules/static are delt with. ACPI attachment
should be done.
This drivers registers with the watchdod(4) interface
Work to do:
- BT interface
- IPMB mode
This has been tested on Dell PE2850, PE2650 & PE850 with i386 & amd64
kernel.
I will link this into the build on next week.
Tom Rhodes, helped me with the man page.
Sponsored by: IronPort Systems Inc.
Inspired from: ipmitool & Linux
o add dfs+radar hooks; DFS is presently disabled in the hal
o channel and mode handling changes
o various api changes
o be more aggressive about iq calibration settling so ap mode
operation is better immediately after startup
o rfkill/rfsilent sysctl support
o tpc ack/cts sysctl support
MFC after: 2 weeks
o assume all data frames have been classified so there's no need
to check if QoS is being used, just fetch the wme priority from
the mbuf
o fix double counting of noack frames
o fix nearby comment
MFC after: 2 weeks
o pull nexttbtt forward in adhoc mode too
o resync beacon timers on joining a bss or ibss as the tstamp we
collected while scanning is almost certainly out of date
Note we may need to refine the ibss mode check in ath_recv_mgmt.
Reviewed by: avatar, dyoung
Obtained from: atheros
MFC after: 2 weeks
frame and if we get a beacon miss interrupt ignore it if we've received
a frame within the beacon miss interval. This should never trigger
and the handling at the net80211 layer should likewise deal with this
but it doesn't hurt and can suppress extranous probe request frames.
Note that we can legtimately get a bmiss when under heavy load.
MFC after: 2 weeks
- Restart watchdog if we *did* processed any descriptors. [1]
- Log the watchdog event if the link is *up*. [2]
PR: kern/92948 [1]
Submitted by: Mihail Balikov <mihail.balikov interbgc.com> [1]
PR: kern/92895 [2]
Submitted by: Vladimir Ivanov <wawa yandex-team.ru> [2]
than just deleting them. Also add comments about why we do this.
Given the current behavior of delete_child, I don't think this changes
anything. It just feels cleaner.
dereferencing) since a NULL value would be a bug here.
Note: Both affected functions look very similar. A refactoring may
be beneficial.
CID: 483, 485
Found with: Coverity Prevent(tm)
Discussed with: ariff
MFC after: 5 days
needed here, except there's a bug which results in detaching the device
twice.
Move the NULL pointer check to the beginning of the function and convert
it into a KASSERT.
CID: 420
Found with: Coverity Prevent(tm)
Discussed with: ariff
MFC after: 5 days
Control) devices as console. These are microcontrollers which are either
on-board or part of an add-on card and provide terminal server, remote
power switch and monitoring functionality. For console usage these are
connected to the rest of the system via a SCC or an UART. This commit adds
support for the following variants (corresponds to what 'input-device' and
'output-device' have to be set to):
rsc found on-board in E250 and supposedly some Netra, connected
via a SAB82532, com. parameters can be determined via OFW
rsc-console RSC card found in E280R, Fire V4x0, Fire V8x0, connected
via a NS16550, hardwired to 115200 8N1
lom-console LOMlite2 card found in Netra 20/T4, connected via a NS16550,
hardwired to 9600 8N1
- Add my copyright to uart_cpu_sparc64.c as I've rewritten about one third
of that file over time.
Tested on: E250, E280R
Thanks to: dwhite@ for providing access to an E280R
OK'ed by: marcel
MFC after: 1 week
casting a structure to a uint32_t *. Many drivers in the tree do this, but
I'll not update them until these changes can be reviewed by the pedantic
standards folks.
in order to query the underlying Windows driver for the station address
and some other properties. There is a slim chance that the card may
receive a packet and indicate it up to us before ndis_attach() can call
ndis_halt_nic(). This is bad, because both the softc structure and
the ifnet structure aren't fully initialized yet: many pointers are
still NULL, so if we make it into ndis_rxeof(), we will panic.
To fix this, we need to do the following:
- Move the calls to IoAllocateWorkItem() to before the call to ndis_init_nic().
- Move the initialization of the RX DPC and status callback function pointers
to before ndis_init_nic() as well.
- Modify ndis_rxeof() to check if the IFF_DRV_RUNNING flag is set. If it
isn't, we return any supplied NDIS_PACKETs to the NIC without processing
them.
This fixes a crash than can occur when activating a wireless NIC in
close proximity to a very busy wireless network, reported by Ryan
Beasley (ryan%^$!ATgoddamnbastard-****!!!DOTorg.
MFC after: 3 days
are bus_addr_t, not bus_size_t.
In any case, turn off DAC support entirely until it is revamped to actually
work *correctly* for 64 bit platforms (not using a PAE definition and for
both initiator and target mode).
Treat SIOCADDMULTI and SIOCDELMULTI the same, since they had the same code
Remove redundant assignment to error
Convert to using the altq interface completely.
to sbus_mdvec.dv_clock as sbus_mdvec.dv_clock is meant to be specified
in MHz. While this was a bug it shouldn't have affected FreeBSD/sparc64
as sbus_mdvec.dv_clock is used to limit the clock rate of chips when
a machine isn't able to support them at maximum speed which isn't the
case for sun4u machines.
- Remove the code that checks whether the clock frequency returned by
sbus_get_clockfreq() is 0 and falls back to 25MHz if it is as that's
already done in sbus(4).
Approved by: mjacob
MFC after: 3 days
routines.
- Add or replace cpu_spinwait() with DELAY(1) to a few of the busy
loops when reading from the controller to work around firmware bugs
which can crash the controller.
with pseudo header for tcp/udp packets). This could save one in_pseudo() call
per incoming tcp/udp packet.
Approved by: glebius (mentor)
MFC after: 3 weeks
capability is present as not all devices supported by the agp_i810 driver
(such as i915) have the AGP capability. Instead, add an identify routine
to the agp_i810 driver that uses the PCI ID to determine if it should
create an agp child device.
to process. It could give us [significant?] perfomance increase if there is big
difference between RX/TX flows.
Submitted by: Mihail Balikov <mihail.balikov AT interbgc DOT com>
Approved by: glebius (mentor)
MFC after: 3 days
synchronized on every call of bge_poll_locked().
Suggested by: Mihail Balikov <mihail.balikov AT interbgc DOT com>
Approved by: glebius (mentor)
MFC after: 3 days
2) add missing bus_dmamap_sync() call in bge_intr()
Tested by: Husnu Demir <hdemir AT metu DOT edu DOT tr>
Approved by: glebius (mentor)
MFC after: 3 days
try to use the registrant for numbers in this file, not the OEM that
put their label on it. Use PNY's real number 0x154b. Add another PNY
atachmate with quirks from a PR filed a while ago, but that I can't
seem to find now...
from NetBSD. This driver actually can replace lnc(4). Advantages over
lnc(4) are:
- Cleaner and more flexible regarding MD needs.
- Endian-clean and MPSAFE.
- Supports ALTQ, VLAN_MTU, ifmedia.
- Uses 32bit DMA for the PCI variants.
This commit includes front-ends for the dma(4) pseudo-bus found on SBus-
based sparc64 machines (thus supports the on-board LANCE in Sun Ultra 1)
and PCI. In order to actually replace lnc(4), the front-ends for ISA and
the PC98 CBUS would have to be added but for which I don't have hardware
to test.
Reviewed and some improvements by: yongari
Tested on: i386, sparc64
support. Which reminds me that I'm not even sure if this works on _any_
laptop at all. :-o
PR: kern/90607
Submitted by: "Wojciech A. Koszek" <dunstan -at- freebsd.czest.pl>
MFC after: 3 days
This is supposed to fix some Coverity Prevent errors (Ariff didn't
looked at the CID's (ENOTIME), I just told him that there are some problems
in function dsp_ioctl()).
CID: 215-218
Found with: Coverity Prevent(tm)
Submitted by: ariff
MFC after: 5 days
o Change MEM_READ_1/MEM_READ_4 into macros (move them to if_iwireg.h)
o Add support for association LED
o Silently discard f/w notifications that are unknown (fixes spurious
"unknown notification 15" in logs with latest firmware)
o Fix scanning of 5GHz channels
into the card's memory.
# this eliminates a more of the ifdef soup in if_ed and if_edvar
# I've fixed the cbus drivers, but can't test them all easily.
If I've broken anything, please let me know.
to properly configure the right interface to use.
Also call the mediachg function when we set flags UP and are already
running. If this were a pure ifmedia driver, we'd not need to do this
since we'd be ignoring the linkX flags.
This reduces the number of ifdefs to support sub-devices a little as a
nice side effect. It also reduces the number of hpp interfaces
exposed by 33%.
man page that the ifconfig option link2 is used to disable the AUI
transceiver on the 3com boards (should also say HP PC Lan+). This
makes the connection clearer.
Add a note about why we set this flag prior to attaching the device.
We never set or clear the flag later, only test it. There can be no
races here, but this might be asthetically displeasing to some. Also
note that we may no longer need to have this knob at all as we may be
able to do it with the more sophisticated rc.d scripts we have today I
think the only reason it is there is because we didn't used to allow
its proper setting when configured to get the IP address via DHCP.
I'll note that this would be better handled by using ifmedia for all
ed cards, not just those with a miibus...
This is important with MegaLib, when issuing a GET_REBUILD_PROG since
it returns an error if the drive is not in rebuild state.
This will be MFC'ed shortly.
Submitted by: ps
Reviewed by: scottl
Found by: ambrisko
system LED on or off. Unlike the EBus LED AUXIO register where the
remaining bits are unused the upper bits of the SBus AUXIO register
are used to control other things like the link test enable pin of
the on-board NIC which we don't want to change as a side-effect.
- Remove the superfluous bzero()'ing of the softc obtained from
device_get_softc().
Reviewed by: yongari
MFC after: 3 days
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.
Add in the Linux IOCTL shim and create the megadev0 device so
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.
Add glue to build the modules but don't tie it into the build
yet until I test it from the CVS repo. via the mirror on an
amd64 machine.
Tie this into the Linux32 emulation on amd64 so the tools can
run on amd64 kernel.
Cleaned up by: ps (amr_linux.c)
side effect that legacy ATA controllers at irq14 and irq15 cannot share
interrupts with anything else without major problems.
This fixes the ATAPI DMA problems some systems/devices have seen.
(1) Fix DMA alignment, based on bytes per sample.
feeder_rate.c:
Handle strayed bytes (mostly caused by #1) better.
This DMA alignment issues are extremely hard to reproduce unless
the user happen to have a 32bit capable soundcards (ATI IXP) and
knowledgeable enough to force it to operate under pure 32bit
operations on both record and play directions.
up to date. Principle changes for this reelase is to support 2K Port Login
firmware. This allows us to support the 2322 (and 2422 4Gb) cards which only
come with the 2K Port Login firmware. The 2322 should now work- but we don't
have firmware sets for it in ispfw (as the change to load 2K Port Login f/w
hasn't been made- that f/w is so big it has to be loaded in more than one
chunk).
Other changes are the beginnings of cleaning up some long standing target
mode issues. The next changes here will incorporate a lot of bug fixes
from others.
Finally, some copyright cleanup and attempts to make the parts of the
driver that are FreeBSD specific start conforming more to FreeBSD style.
MFC after: 1 month
feeder.h:
feeder.c:
- Implement scoring mechanisme to select best format for conversion.
This is actually part of newer format chaining procedures which
will be commited someday. Confusion during chaining process solved
by this scoring since it will try to reduce list of from/to formats
to a single, best format.
Related PR: kern/91683
channel.c:
- Simplify feeder building process since we have smarter format
chaining.
feeder_fmt.c:
- Add few more sign conversion feeders for 24 and 32 bit format.
feeder_rate.c:
- Force buffer / bytes allignment. Unaligned buffer may cause
panics during recording on pure 32bit sample format if it
involves feeder_rate as part of feeders chain.
Tested on: ATI IXP, force 32bit recording.
MFC after: 5 days
o fix contention window
o silently discard received frames that are too short
o simplify lookup of 802.11a channels (we know they exist)
o fix short preamble support
o add short slot support
o fix eifs settings
o many consistency tweaks
share devclass pointers, a mistake I've encouraged in the past) and
move the declaration of the pci_driver kobj class from cardbus.c to
pci_private.h so that other drivers can inherit from pci_driver.
hacking:
- Remove all spaces at eol.
- Improve style(9) in most frequently edited functions.
- In em_encap() push variables for 82544 workaround in the block
where they are only used.
- In em_get_buf() remove unused variable.
as input/output interface errors.
- Keep values of rx/tx discards & tx collisions inside struct bge_softc.
So we can keep statistic across ifconfig down/up runs (cause bringing
bge up will reset chip).
Approved by: glebius (mentor)
MFC after: 1 week
ATI EHCI controllers exhibit simmilar stall issues and require
this dropped interrupts workaround. Be verbose about it.
ehci.c:
ehcivar.h:
Slight change in comments to note about issues surrounding both
VIA and ATI EHCI controllers.
Approved by: iedowse
an interrupt appears to occur before the transfer has been marked
as completed. This caused umass transfers to get stuck, especially
when writing large files. The workaround sets up a timer that
rechecks for missed completed transfers if some operations are still
pending. Other suggested workarounds, such as performing a PCI read
immediately after acknowledging the interrupts, do not appear to
help.
Obtained from: OpenBSD
same behavior to be controlled by the sysctls, hw.syscons.kbd_kbdkey
and hw.syscons.kbd_reboot respectively.
Apologies to the submitter for taking so long to commit this simple
change.
PR: kern/72728
Submitted by: Luca Morettoni <morettoni at libero dot it>
MFC After: 3 days
taskqueue_start_threads(struct taskqueue **, int count, int pri,
const char *name, ...);
This allows the creation of 1 or more threads that will service a single
taskqueue. Also rework the taskqueue_create() API to remove the API change
that was introduced a while back. Creating a taskqueue doesn't rely on
the presence of a process structure, and the proc mechanics are much better
encapsulated in taskqueue_start_threads(). Also clean up the
taskqueue_terminate() and taskqueue_free() functions to safely drain
pending tasks and remove all associated threads.
The TASKQUEUE_DEFINE and TASKQUEUE_DEFINE_THREAD macros have been changed
to use the new API, but drivers compiled against the old definitions will
still work. Thus, recompiling drivers is not a strict requirement.
- Add support for adjusting the fan speed if the fan control mode is manual
Documentation for the relevant embedded controller register was obtained from
http://www.thinkwiki.org/wiki/Patch_for_controlling_fan_speed
Tested on: R51 by Fabian Keil
T41p by markus
Requested by: many
Approved by: philip
MFC after: 1 week
2) use more robust way of link state handling for BCM5700 rev.B2 chip
3) workaround bug of some BCM570x chips which cause spurious "link up" messages
4) fix bug: some BCM570x chips was unable to detect link state changes after
ifconfig down/up sequence until any 'non-link related' interrupt generated.
(this happened due to pending internal link state attention which blocked
interrupt generation)
Approved by: glebius (mentor)
MFC after: 1 week
the the interface has been configured. I'm not sure how this could ever
have worked before, but it should be fixed now. Also break out the interrupt
degresitration function into it's own step.
before. The symptom is that the battery inform us its charge and discharge
at the same time...
* fix bst.rate to correctly output the (dis)charging rate. We'll use
the current average over one minute command and not the at_rate command.
Note that this method is not correct if the capacity_mode is set, but
since we don't set it ourself, it is not a problem.
The at_rate do not give the actual rate but is used to compute the
estimated time for (dis)charging a battery. We should actually
write an estimation of the actual rate using at_rate cmd and then
perform a read to the various estimators.
Approved by: njl
MFC after: 2 days
The minimum / maximum speed was way too low / high!
minspeed = 2000 - is this for real ?
maxspeed = 767999 - is this for real ?????
Wrap everything into 8000 - 48000 boundary, just to be safe.
MFC after: 3 days
- Mark MPSAFE since most of the locking procedures already implemented.
- Turn on inverted external amplifier sense flag for selected boards.
Tested by: bland
MFC after: 1 week
- Only update the rx ring consumer pointer after running through the rx loop,
not with each iteration through the loop.
- If possible, use a fast interupt handler instead of an ithread handler. Use
the interrupt handler to check and squelch the interrupt, then schedule a
taskqueue to do the actual work. This has three benefits:
- Eliminates the 'interrupt aliasing' problem found in many chipsets by
allowing the driver to mask the interrupt in the NIC instead of the
OS masking the interrupt in the APIC.
- Allows the driver to control the amount of work done in the interrupt
handler. This results in what I call 'adaptive polling', where you get
the latency benefits of a quick response to interrupts with the
interrupt mitigation and work partitioning of polling. Polling is still
an option in the driver, but I consider it orthogonal to this work.
- Don't hold the driver lock in the RX handler. The handler and all data
associated is effectively serialized already. This eliminates the cost of
dropping and reaquiring the lock for every receieved packet. The result
is much lower contention for the driver lock, resulting in lower CPU usage
and lower latency for interactive workloads.
The amount of work done in the taskqueue is controlled by the sysctl
dev.em.N.rx_processing_limit
and tunable
hw.em.rx_process_limit
Setting these to -1 effectively removes the limit.
The fast interrupt and taskqueue can be disabled by defining NO_EM_FASTINTR.
This work has been shown to increase fast-forwarding from ~570 kpps to
~750 kpps (note that the same NIC hardware seems unable to transmit more than
800 kpps, so this increase appears to be limited almost solely by the
hardware). Gains have been shown in other workloads, ranging from better
performance to elimination of over-saturation livelocks.
Thanks to Andre Opperman for his time and resources from his network
performance project in performing much of the testing. Thanks to Gleb
Smirnoff and Danny Braniss for their help in testing also.
Instead of dragging the entire ICH4/82801DB into this mess, select
only few boards based on pci subdevice / subvendor.
Tested by: Daisuke Orikasa <luxury-acura-3.5rl at nifty.com>
MFC after: 3 days
This is based on MCPC USB mobile phone guide line (MCPC-GL005)
Some other 3G system or so will work with this driver.
Kyocera PHS terminal (a.k.a. Kyopon) is known to work, which
is now supported by umodem(4) driver.
o record tsf in tx+rx frames
o switch from raw rssi to dbm for signal data and record both
signal and noise floor data (hacked for now to assume a fixed
noise floor; is correct with new hal)
o add monpass sysctl to control which rx'd frames are passed
up with errors; especially useful to see frames with CRC errors
o mark 'd packets w/ a CRC error with radiotap's BADFCS flag
Also add placeholder code for calibrating the noise floor when
using newer hals.
Reviewed by: avatar
MFC after: 1 week
better, I discovered sn doing too many pointer dereferences. This
driver would do silly things like:
sn_foo(struct ifnet *ifp)
{
struct sn_softc *sc = ifp->if_softc;
sc->ifp->mumble
/* Other stuff */
}
while /* other stuff */ usually needed sc, the extra deref isn't
needed. Eliminate a few dozen of them.
modules would have overlapping names.
- Only create /dev/si_control for unit 0.
Tested by: Joerg Lehners Joerg dot Lehners at informatik dot
uni-oldenburg dot de (on 6.x)
MFC after: 1 week
various pcib drivers to use their own private devclass_t variables for
their modules.
- Use the DEFINE_CLASS_0() macro to declare drivers for the various pcib
drivers while I'm here.
doesn't have any actual interrupts is listed in a _PRT entry, only print
a warning rather than panic'ing when we walk the _PRT's to build up count
of entries that reference a given link (the counts are used as weights so
that we can attempt to balance the load across IRQs used by link devices).
Instead, only panic if we attempt to use the _PRT entry to route an
interrupt for a device.
PR: i386/89545
Tested by: anders
- MPSAFE
- Fix / reorganize attach routine. Device specific initialization must
be done after generic bus / DMA setup. At last, Virtual Channels
(vchan) works as expected.
Note: Recent commit / fix against this driver proves that major enhancements
on the generic sound layer does indeed help to expose flaw within
device specific code. There are probably other drivers that need to
be addressed as well.
Tested by: barner
MFC after: 1 week
ifm_status and ifm_active. IFM_10_T gets set in the ifm_active field,
not in the ifm_status field, as far as I can tell.
Note: this was to enable a workaround that's rarely enabled. I don't know
how to corrupt my eeprom to test it, and would rather not know...
signal is received during the msleep, the msleep is retried
indefinitely as it just keeps returning ERESTART because of
the pending signal.
Instead, just don't PCATCH - the signal can wait.
Sponsored by: Sophos/ActiveState
requiried to keep consistent softc state before/after callback function
invocation and supposed to be sligntly faster than previous one as it
wouldn't incur callback overhead. With this change callback function
was gone.
- Decrease TI_MAXTXSEGS to 32 from 128. It seems that most mbuf chain
length is less than 32 and it would be re-packed with m_defrag(9) if
its chain length is larger than TI_MAXTXSEGS. This would protect ti(4)
against possible kernel stack overflow when txsegs[] is put on stack.
Alternatively, we can embed the txsegs[] into softc. However, that
would waste memory and make Tx/Rx speration hard when we want to
sperate Tx/Rx handlers to optimize locking.
- Fix dma map tracking used in Tx path. Previously it used the dma map
of the last mbuf chain in ti_txeof() which was incorrect as ti(4)
used dma map of the first mbuf chain when it loads a mbuf chain with
bus_dmamap_load_mbuf(9). Correct the bug by introducing queues that
keep track of active/inactive dma maps/mbuf chain.
- Use ti_txcnt to check whether driver need to set watchdog timer instead
of blidnly clearing the timer in ti_txeof().
- Remove the 3rd arg. of ti_encap(). Since ti(4) now caches the last
descriptor index(ti_tx_saved_prodidx) used in Tx there is no need to
pass it as a fuction arg.
- Change data type of producer/consumer index to int from u_int16_t in
order to remove implicit type conversions in Tx/Rx handlers.
- Check interface queue before getting a mbuf chain to reduce locking
overhead.
- Check number of available Tx descriptores to be 16 or higher in
ti_start(). This wouldn't protect Tx descriptor shortage but it would
reduce number of bus_dmamap_unload(9) calls in ti_encap() when we are
about to running out of Tx descriptors.
- Command NIC to send packets ony when the driver really has packets
enqueued. Previously it always set TI_MB_SENDPROD_IDX which would
command NIC to DMA Tx descriptors into NIC local memory regardless
of Tx descriptor changes.
Reviewed by: scottl
allocating a resource that's in the card itself.
Remove more now-redundant resource_list_add, and now-redunant code
that lives in the pci layer.
# This fixes the atheros card that I have which had its CIS in one of
# the BARs. Don't know yet if this fixes the amd64 issues reported.
USB HID device that allows to plug two PS2 controllers. This specific
device doesn't work yet but will as soon as we support devices with
multiple report IDs.
MFC after: 3 days
broken report descriptor. While I'm here, make all the other report
descriptors const to match the newly added one.
Obtained from: NetBSD
MFC after: 1 week
lack a report descriptor and don't use the standard interface class.
This patch works around these deficiencies so that the uhid(4) driver
can recognize and use those broken devices.
PR: usb/90141
Submitted by: Ed Schouten <ed@fxq.nl> (with minor mods from me)
MFC after: 1 week
force allocation of unallocated BARs (cardbus uses this to preallocate
everything). Add a prefetchmask to allow for busses that get prefetch
hints to set them. Addjust pci_add_map and pci_ata_maps to take a new
force flag which pci_add_resources will pass in. Implement 'force' in
pci_add_map. Write new value of allocated resource into the bar, if
the allocation succeeded (we should have done this before, but with
the new force the bug was very obvious).
This should reduce huge playback / recording latency for
applications that try to act smarter and manage their own
buffering (XMMS, Skype, etc.).
Note to Skype + via8xxx users: Remove previous hackish
"hint.pcm.<unit>.via_dxs_disabled" from kernel hint and see
whether this changes cure all those annoying sound issues.
try very hard to be perfect. However, these attempts broke down when
there were large numbers of resources. We'd not be able to map them all.
Instead, accept that we might pass more range to thse subbus than
might be optimal be able to compute. However, there's little harm in
this and it allows us to pass greater resources through.
# it has been suggested that we allocate a fixed amount of resources
# on attach and give it out upon request. This might not be a bad idea...
cardbus_cis.c to this file, some code was not merged and thus resource
list entries were invalid. They didn't have a resources attached to
them.
However, the problem was masked for some time later, because newer
resources list entries were added to the head of the list, and
resource_list_find() always returned the first matching resource list
entry. Usually the underlying driver allocated a valid resource and
added it to the head of the list, and invalid one wasn't used.
In rev. 1.174 of subr_bus.c the sorting of resource list entries was
reversed demasking the problem in cardbus_alloc_resources().
This commit fixes the problem returning back some code from
cardbus_cis.c, pre-1.49 revisions.
PR: kern/87114
PR: kern/90441
Hardware provided by: Vasily Olekhov <olekhov yandex.ru>
Reviewed by: imp
. remove unnecessay header files after Scott's bus_dma(9) commit.
. remove global variable tis which was introduced at the time of
zero_copy(9) changes. The variable tis was not used at all. The
same applyes to ti_links in softc so axe it.
. deregister variables.
. axe ti_vhandle and switch to use explicit register access for
accessing NIC local memory. Creates three variants of ti_mem to
read/write NIC local memory(ti_mem_read, ti_mem_write) and clearing
NIC local memory(ti_mem_zero). This greatly enhances code
readability and have ti(4) drop using shared memory scheme for
Tigon 1. As Tigon 1 switched to use explicit register access for Tx,
axe ti_tx_ring_nic/ti_cmd_ring in softc.(Tigon 2 used to host ring
scheme which means there is no need to access NIC local memory via
register access for Tx and NIC would DMA the modified Tx rings into
its local memory.) [1]
. introduce new macro TI_EVENT_*/TI_CMD_* to handle NIC envent/command.
Instead of using bit fields assginment for accessing the event, use
shift operations to set/get it. [1]
. add additional check for valid DMA tags in ti_free_dmamaps().
. add missing bus_dmamap_sync/bus_dmamap_unload in ti_free_*_ring_*.
. fix locking nits(MTX_RECURSE mutex) and make ti(4) MPSAFE.
. change data type of ti_rdata_phys to bus_addr_t and don't blindly
cast to uint32_t.
. rearrange detach path and make ti(4) survive during device detach.
. for Tigon 1, use explicit register access for checking Tx descriptors
in ti_encap()/ti_txeof(). [1]
. properly call bus_dmamap_sync(9) for updating statistics.
. remove extra semicolon in ti_encap()
. rewrite loading MAC address to work on strict-alignment architectures.
. move TI_RD_OFF macro to if_tireg.h
. axe ETHER_ALIGN as it's already defined in <net/ethernet.h>.
. make macros immuine from expansion by adding parenthesis and do-while.
. remove alpha specific hack as vtophys(9) is no longer used in ti(4)
after Scott's bus_dma(9) fix.
Reviewed by: scottl
Obtained from: OpenBSD [1]
POSIX. This also makes the struct correct we ever implement an i386-time64
architecture. Not that we need too.
Reviewed by: imp, brooks
Approved by: njl (acpica), des (no objects, touches procfs)
Tested with: make universe
if we need a valid MAC address (for probing the media for example) before
ether_ifattach() has been called since IF_LLADDR() is NULL then.
Tested by: tisco
except for BGE_CHIPID_BCM5700_B0, which is buggy.
- All bge(4) supported hardware, has a bug that produces incorrect checksums
on Ethernet runts. However, in case of a transmitted packet, the latter can
be padded with zeroes, and the checksum would be correct. (Probably chip
includes the pad data into checksum). In case of receive, we just don't
trust checksum data in received runts.
Obtained from: NetBSD (jonathan) via Mihail Balikov
Previously it always returned 0 which means success regardless of
EEPROM status.
While here, add a check whether EEPROM read is successful.
Submitted by: jkim
- removed unused funtion bge_handle_events().
- removed bus_dmamap_destroy(9) calls for DMA maps created by
bus_dmamem_alloc(9). This should fix panics seen on sparc64
in device detach.
- added check for parent DMA tag creation.
- switched to use __NO_STRICT_ALIGNMENT as bge(4) supports all
architectures.
- added missing bus_dmamap_sync(9) in bge_txeof().
- added missing bus_dmamap_sync(9) in bge_encap().
- corrected memory synchronization operation on status block.
As the driver just read status block that was DMAed by NIC it
should use BUS_DMASYNC_POSTREAD. Likewise the driver does not
need to write status block back, so remove unnecessary
bus_dmamap_sync(9) calls in bge_intr().
- corrected memory synchronization operation on RX return ring.
The driver only read the block so remove unnecessary
bus_dmamap_sync(9) in bge_rxeof().
- force bus_dmamap_sync(9) for only modified descriptors. Blindly
synching all desciptor rings would reduce performance.
- call bus_dmamap_sync(9) for DMA maps that were modified in bge_rxeof().
Reviewed by: jkim(initial version)
Tested by: glebius(i386), jkim(amd64 initial version)
the addition of pci_find_extcap().
- Change the drm drivers to attach to vgapci. This is #ifdef'd so the
code can be shared across branches.
- Use pci_find_extcap() to look for AGP and PCIE capabilities in drm.
- GC all the drmsub stuff for i810/i830/i915. The agp and drm devices are
now both children of vgapci.
as a bus so that other drivers such as drm(4), acpi_video(4), and agp(4)
can attach to it thus allowing multiple drivers for the same device. It
also removes the need for the drmsub hack for the i8[13]0/i915 drm and agp
drivers.
attach to the hostb driver instead. This means that agp can now be loaded
at runtime (in theory at least). Also, the drivers no longer have to
explicity call device_verbose() to cancel out any earlier calls to
device_quiet() by the hostb(4) driver (this shows a limitation in new-bus,
drivers really shouldn't be doing device_quiet() until they know they are
going to drive that device, i.e. in attach).
duplicated anyways) and into a single MI driver. Extend the driver a bit
to implement the bus and PCI kobj interfaces such that other drivers can
attach to it and transparently act as if their parent device is the PCI
bus (for the most part).
drivers already map sections into KVA as needed anyway. Note that this
will probably break the nvidia driver, but I will coordinate to get that
fixed.
MFC after: 2 weeks
to search for a specific extended capability. If the specified capability
is found for the given device, then the function returns success and
optionally returns the offset of that capability. If the capability is
not found, the function returns an error.
we can cache its value in the softc. Eliminates one PCI register
write per call to bge_start().
A 1.8% speedup for UDP_RR test on my old box.
Obtained from: NetBSD(jonathan) via delphij
case if memory allocation failed.
- Remove fourth argument from VLAN_INPUT_TAG(), that was used
incorrectly in almost all drivers. Indicate failure with
mbuf value of NULL.
In collaboration with: yongari, ru, sam
command. This fixes some weird booting issues on newer versions
of the firmware on the MSA20.
Reported by: Philippe Pegon <Philippe dot Pegon at crc dot u-strasbg dot fr>
- Give up endianess support and switch to native-endian format for
accessing hardware structures. In fact embedded processor for
BCM57xx is big-endian architure(MIPS) and it requires native-endian
format for NIC structures.The NIC performs necessary byte/word
swapping depending on programmed endian type.
- With above changes all htole16/htole32 calls were gone.
- Remove bge_vhandle member in softc and changed to use explicit
register access. This may add additional performance penalty
that than that of previous memory access. But most of the access
is performed on initialization phase(e.g. RCB setup), it would be
negligible.
Due to incorrect use of bus_dma(9) in bge(4) it still panics sparc64
system in device detach path. The issue would be fixed in next patch.
Reviewed by: jkim (initial version)
Silence from: ps
Tested by: glebius
Obtained from: NetBSD via OpenBSD
1. Implement a large set of ioctl shims so that the Linux management apps
from LSI will work. This includes infrastructure to support adding, deleting
and rescanning arrays at runtime. This is based on work from Doug Ambrosko,
heavily augmented by LSI and Yahoo.
2. Implement full 64-bit DMA support. Systems with more than 4GB of RAM
can now operate without the cost of bounce buffers. Cards that cannot do
64-bit DMA will automatically revert to using bounce buffers. This option
can be forced off by setting the 'hw.amr.force_sg32" tunable in the loader.
It should only be turned off for debugging purposes. This work was sponsored
by Yahoo.
3. Streamline the command delivery and interrupt handler paths after
much discussion with Dell and LSI. The logic now closely matches the
intended design, making it both more robust and much faster. Certain
i/o failures under heavy load should be fixed with this.
4. Optimize the locking. In the interrupt handler, the card can be checked
for completed commands without any locks held, due to the handler being
implicitely serialized and there being no need to look at any shared data.
Only grab the lock to return the command structure to the free pool. A
small optimization can still be made to collect all of the completions
together and then free them together under a single lock.
Items 3 and 4 significantly increase the performance of the driver. On an
LSI 320-2X card, transactions per second went from 13,000 to 31,000 in my
testing with these changes. However, these changes are still fairly
experimental and shouldn't be merged to 6.x until there is more testing.
Thanks to Doug Ambrosko, LSI, Dell, and Yahoo for contributing towards
this.
to use busdma. Unlike most of the other drivers, but similar to the
if_em driver, pre-allocate the dmamaps at init time instead of allocating
them on the fly when descriptors need to be filled. This isn't ideal right
now because a map is allocated for every descriptor slot in the tx, rx, mini,
and jumbo rings (which is a lot!) in order to simplify the bookkeeping, even
though the driver might support filling only a subset of those slots.
Luckily, maps are typically NULL on i386 and amd64, so the cost isn't
very high. It could be an issue with sparc64, but the driver isn't endian
clean either, and that is a much bigger problem to solve first.
Note that jumbo frame support is under-tested, and I'm not even sure if
it till really works correctly given the evil VM magic that is does.
The changes here attempt to preserve the existing semanitcs.
Thanks to Martin Nillson for contributing the Netgear card for this work.
MFC-After: 3 weeks
compilation of kernels without ns8250 support but using the uart framework.
These kernels will be for machines where size matters more, so including code
that can never be executed is undesriable...
working at all and only saw "nve0: device timeout (N)" messages.
- Setup PHY before handing control to NVidia API setting
speed, duplex, enabling interrupts, etc.
- Add restriction of MAXADDR_32BIT for high address to contigmalloc
to make the driver work on machines with 4+GB of memory.
PR: kern/85583, kern/88045
Tested by: scottl, others earlier version
MFC after: 10 days
transmitted bits was between 8.6180us and 8.6200us when we used a RCLK
of 16.500MHz. This is a little low (should be 8.6805us). This error
is exactly the error one would expect if it actually had a 16.384MHz
watch oscillator (as suggested by garrett) instead of using the PCI
RCLK. Assume that the pci clock therefore wasn't really used, but
instead the cheap 16.384MH watch quartz oscillator. This gives bits
in the 8.6800us to 8.6810us ranage, which matches theoretical.
Submitted by: garrett
cluster allocator, that wasn't MPSAFE. Instead, utilize our new generic
UMA jumbo cluster allocator. Since UMA gives us a 9k piece that is contigous
in virtual memory, but isn't contigous in physical memory we need to handle
a few segments. To deal with this we utilize Tigon chip feature - extended
RX descriptors, that can handle up to four DMA segments for one frame.
Details:
o Remove bge_alloc_jumbo_mem(), bge_free_jumbo_mem(),
bge_jalloc(), bge_jfree() functions.
o Remove SLIST heads, bge_jumbo_tag, bge_jumbo_map from softc.
o Use extended RX BDs for Jumbo receive producer ring, and
initialize it appropriately.
o New bge_newbuf_jumbo():
- Allocate an mbuf with Jumbo cluster with help of m_cljget().
- Load the cluster for DMA with help of bus_dmamap_load_mbuf_sg().
- Assert that we got 3 segments in the DMA mapping.
- Fill in these 3 segments into the extended RX descriptor.
2) rework link state detection code & use it in POLLING mode
3) fix 2 bugs in link state detection code:
a) driver unable to detect link loss on bcm5721
b) on bcm570x chips (tested on bcm5700 bcm5701 bcm5702) driver fails
to detect link loss with probability 1/6 (solved in brgphy.c)
Devices working in TBI mode should not be affected by this change.
Approved by: glebius (mentor)
MFC after: 1 month
"done" method so that for non-repeat operations we have completely
finished with the transfer by the time the callback is invoked.
This makes it possible to recycle a transfer from within the callback
routine for the same transfer. Previously this almost worked, but
with OHCI controllers calling the "done" method after the callback
would zero out some important fields needed by the recycled transfer.
Only some usb peripheral drivers such as ucom appear to rely on the
ability to reuse a transfer from its callback.
MFC after: 1 week
time ago appears to be based not on the typical 1.8432MHz clock, or
the other more typical multiple of 8 of this (14.7456MHz), but instead
it appears to be 1/2 the PCI clock rate or 16.50000MHz. I'm not 100%
sure that this is right, but since I did the original entry, I'm going
to go ahead and modify it. With the 14.7456MHz value, I was getting
bits that were ~7.3us instead of ~8.6us like they are supposed to be.
My measuring gear for today is a stupid handheld scope with two
signficant digits. So I don't know if it is 33.000000/2 MHz or some
other value close to 16.5MHz, but 16.5MHz works well enough for me to
use a couple of different devices at 115200 baud, and is a nice even
multiple of a well known clock frequency...
acquired anywhere in the driver now.
- Axe the spin mutex used for the nve_oslock*() routines. The driver lock
already provides sufficient synchronization.
- Don't mess around with IFF_UP when the link state changes. IFF_UP is
an administrative flag, not a link status indicator.
MFC after: 1 week
immediately from acpi_pci_link_route_interrupt() since we aren't going
to have a valid pci_link device to talk to try to route interrupts. This
fixes a page fault if you disable just pci_link. Note that trying to use
ACPI without pci_link is probably not advised however.
MFC after: 1 week
Tested by: Eugene Grosbein eugen at kuzbass dot ru
the eaddr array (introduced in rev. 1.174) prior to writing to it. As
dc_read_eeprom() is told to write only 3 16-bit words to eaddr but eaddr
in fact is somewhat larger removal of the zeroing defeated the check
whether the MAC address is all zero as there can be some random garbage
in eaddr past the 3 words written to it and the check verifys all bits
in eaddr. Solve this by changing the check to verify only the 3 words
(happenning to be ETHER_ADDR_LEN bytes) written to eaddr.
- While here change the notation of "FCode" in a nearby comment to the
official way.
Ok'ed by: marcel, ru
polarity. Some machines route PCI IRQs to an ISA IRQ but fail to include
an interrupt override entry to set the polarity and trigger of the given
ISA IRQ in their MADT table.
PR: usb/74989
Reported by: Julien Gabel jpeg at thilelli dot net
MFC after: 1 week
and some fixes from Motomichi Matsuzaki. Testing involved many people, but the
final, successful testing was from rwatson who endured several rounds of "it
crashes at XYZ stage" "oh, please correct this typo and try again." The Linux
driver, and to a small extent the limited specs, were both used as a reference
for how to program the chipset.
PR: kern/80396
Submitted by: Martin Mersberger
Update Intel MatrixRAID support to be able to pick up RAID0+1 (RAID10)
and RAID5 arrays without panic'ing.
This has the side effect of now also supporting multiple volumes on
MatrixRAID's now I have the metadata better understood..
HW sponsored by: Mullet Scandinavia AB
commit. Copy the ethernet address into a local buffer, which we know
is sufficiently aligned for the width of the memory accesses that we
do. This also eliminates all suspicious and potentionally harmful
casts.
In collaboration with: ru
- S3 Savage driver ported.
- Added support for ATI_fragment_shader registers for r200.
- Improved r300 support, needed for latest r300 DRI driver.
- (possibly) r300 PCIE support, needs X.Org server from CVS.
- Added support for PCI Matrox cards.
- Software fallbacks fixed for Rage 128, which used to render badly or hang.
- Some issues reported by WITNESS are fixed.
- i915 module Makefile added, as the driver may now be working, but is untested.
- Added scripts for copying and preprocessing DRM CVS for inclusion in the
kernel. Thanks to Daniel Stone for getting me started on that.
appeared to rely on all kinds of non-guaranteed behaviours: the
transfer abort code assumed that TDs with no interrupt timeout
configured would end up on the done queue within 20ms, the done
queue processing assumed that all TDs from a transfer would appear
at the same time, and there were access-after-free bugs triggered
on failed transfers.
Attempt to fix these problems by the following changes:
- Use a maximum (6-frame) interrupt delay instead of no interrupt
delay to ensure that the 20ms wait in ohci_abort_xfer() is enough
for the TDs to have been taken off the hardware done queue.
- Defer cancellation of timeouts and freeing of TDs until we either
hit an error or reach the final TD.
- Remove TDs from the done queue before freeing them so that it
is safe to continue traversing the done queue.
This appears to fix a hang that was reproducable with revision 1.67
or 1.68 of ulpt.c (earlier revisions had a different transfer
pattern). With certain HP printers, the command "true > /dev/ulpt0"
would cause ohci_add_done() to spin because the done queue had a
loop. The list corruption was caused by a 3-TD transfer where the
first TD completed but remained on the internal host controller
done queue because it had no interrupt timeout. When the transfer
timed out, the TD got freed and reused, so it caused a loop in the
done queue when it was inserted a second time from a different
transfer.
Reported by: Alex Pivovarov
MFC after: 1 week
This shouldn't happen as far as the self-id buffer is vaild but
some people have this problem.
PR: kern/83999
Submitted by: Markus Wild <fbsd-lists@dudes.ch>
MFC after: 3 days
- Add locked variants of start, init, and ifmedia_upd.
- Add a mutex to the softc and remove spl calls.
- Use callout(9) rather than timeout(9).
- Setup interrupt handler last in attach.
- Use M_ZERO rather than bzero.
MFC after: 1 week
Tested by: wpaul
- Improve panic message if we fail to read the PCI bus number from a bridge
device.
- Don't try to lookup a BIOS IRQ for a link unless the link is routed via
an ISA IRQ since BIOSen currently only route PCI link devices via ISA
IRQs.
Tested by: Mathieu Prevot bsdhack at club-internet dot fr
MFC after: 1 week
Instead, re-evaluate _BIF only when we get a notify and use the cached
results. We also still evaluate _BIF once on boot. Also, optimize the
init loop a little by only querying for a particular info if it's not valid.
MFC after: 2 days
a newly introduced struct ofw_bus_devinfo which can hold the OFW info
of a device recallable via the ofw_bus KOBJ interface. Introduce a set
of functions ofw_bus_gen_get_*() which use ofw_bus_default_get_devinfo()
to provide generic subroutines for implementing the rest of the ofw_bus
KOBJ interface in a bus driver.
This is inspired by bus_get_resource_list() and bus_generic_rl_*_resource()
and allows to reduce code duplication in bus drivers as they only have
to provide an ofw_bus_default_get_devinfo() implementation in order to
provide the ofw_bus KOBJ interface via ofw_bus_gen_get_*().
- While here add a comment to ofw_bus_if.m describing the intention of
the ofw_bus KOBJ interface.
Reviewed by: marcel
the tree.
- Add locked variants of nve_start(), nve_init(), and nve_ifmedia_upd().
- Use callout_* to manage callouts rather than timeout(9).
- Mark interrupt handler MPSAFE (IFF_NEEDGIANT was already clear).
- Lock the driver lock in driver entry points such as the interrupt
handler, if_start, and if_init rather than locking the driver mutex
in the various work functions called by the binary blob. The spin lock
used by the binary block can probably be stubbed out now.
- Use IFQ_DRV_IS_EMPTY() macro rather than doing it by hand.
- Fix locking in detach.
- Remove some unused fields from the softc.
Tested by: cognet
MFC after: 2 weeks
the IRQ set by the BIOS in existing devices to actually get the correct
bus number of the child PCI bus. I was not reading the bus number from
the bridge device correctly. The __BUS_ACCESSOR() macros (from which
pcib_get_bus() is built) assume that the passed in argument is a child
device. However, at the time I'm reading the bus there is no child
device yet, so I was passing in the pcib device as the child device.
The parent of the pcib device probably returned an error in the case of
a host bridge, thus resulting in random stack garbage for the bus number.
For PCI-PCI bridges, the bus number being used was actually the subvendor
of the PCI-PCI bridge device itself.
MFC after: 1 week
- Don't call tulip_addr_filter() to reset the RX address filter in
tulip_reset() since that gets called before ether_ifattach(). Just
call it in tulip_init_locked().
- Use be16dec() and le16dec() to parse MAC addresses when programming
the RX filter.
- Let ether_ioctl() handle SIOCSIFMTU since we were doing the exact same
thing with the added bonus that we leaked the driver lock if the MTU
was > ETHERMTU in the homerolled version. This part will be MFC'd.
Clue from: wpaul (1)
Stolen from: marcel (2 via patch for dc(4))
MFC after: 1 week
via the DEFAULTS kernel configs. This allows folks to turn it that option
off in the kernel configs if desired without having to hack the source.
This is especially useful since PUC_FASTINTR hangs the kernel boot on my
ultra60 which has two uart(4) devices hung off of a puc(4) device.
I did not enable PUC_FASTINTR by default on powerpc since powerpc does not
currently allow sharing of INTR_FAST with non-INTR_FAST like the other
archs.
buildkernel: provide a real but dummy name to ${DEPENDFILE}
so that the relevant exists() check in bsd.prog.mk fails and
ensures that ${GENHDRS} are built before any other objects.
MFC after: 3 days
- don't force busdma to pre-allocate bounce pages for parent tag.
- use system supplied roundup2 macro instead of rolling its own version.
- TX/RX decriptor length should be multiple of 128. There is no
no need to expand the size with the multiple of 4096.
- don't create/destroy DMA maps in TX/RX handlers. Use pre-allocated
DMA maps. Since creating DMA maps on sparc64 is time consuming
operations(resource mananger overhead), this change should boost
performance on sparc64. I could get > 2x speedup on Ultra60.
- TX/RX descriptors could be aligned on 128 boundary. Aligning them
on PAGE_SIZE is waste of resource.
- don't blindly create TX DMA tag with size of MCLBYTES * 8. The size
is only valid under jumbo frame environments. Instead of using the
hardcoded value, re-compute necessary size on the fly.
- RX side bus_dmamap_load_mbuf_sg(9) support.
- remove unused macro EM_ROUNDUP and constant EM_MMBA.
Reviewed by: scottl
Tested by: glebius
that enabling busmastering would result in PCR bit ON after codec
reset.
While I'm here add DELAY(1) to codec access routine to give reasonable
time to codec operation. Without the delay, it would cause problems on
super-fast machines(> 2GHz). Also enable legacy audio for all 6300ESB,
82801[D-G]B chips. Previously, it enabled legacy audio for 82801DB(ICH4)
chip only.
Reported by: Maxim Maximov mcsi AT mcsi DOT pp DOT ru
Andrew Bliznak andriko.b AT gmail DOT com
Tested by: brueffer, Maxim Maximov, Andrew Bliznak
directory by default) without requiring the user to load them by hand using
e.g iwicontrol. Get rid of the old ioctl crud.
Updated iwi-firmware port coming soon.
Obtained from: OpenBSD
for a notebook with em(4) adapter.
- Introduce tunables em.hw.txd and em.hw.rxd, which allow administrator
to configure number of transmit and receive descriptors.
- Check em.hw.txd and em.hw.rxd against hardware limits [*] and require
them to be multiple of 128.
[*] According to comments in if_em.h the 82540EM/82541ER chips can handle
more than 256 descriptors. Since we don't have this hardware to test,
we decided to mimic NetBSD wm(4) driver, that limits these chips to
256 descriptors.
In collaboration with: yongari
stale when called to reset rate control state causing us to
pickup an invalid index, check for this and skip 'em (things
will eventually get fixed up so this is not harmful)
of volumes that might need administrator attention through device
specific sysctl to simplify device monitoring.
Submitted by: Deomid Ryabkov <myself at rojer dot pp dot ru>
This one simply tries to simplify the logic to select the
buffer sizes. I am not sure it is necessary but the code
seems a bit more readable to me. And at least i have tried
to document how the buffer sizes are computed.
Thanks to luigi for deciphering one of the most cryptic part of
sound driver.
Submitted by: luigi
Approved by: netchild (mentor)
In SNDCTL_DSP_SETFRAGMENT, if you specify both read and
write channels, the existing code first acts on the
read channel, but as a side effect it updates the
arguments (maxfrags, fragsz) passed by the caller according
to acceptable values for the read channel, and then uses the
modified values to act on the write channel.
The problem with this approach is that, given a
(maxfrags, fragsz) user-specified value, the actual
values computed by the read and write channels may differ:
e.g. the read channel might want to allocate more fragments
than what the user specified because it has no side-effects
on the delay and it helps in case of slow readers,
whereas the write channel needs to use as few fragments
as possible to keep the audio latency low (very important
with telephony apps).
This patch stores the values computed by the read channel
into temproary variables so the write channel will use
the actual arguments of the ioctl.
This patch is very helpful with telephony apps such as asterisk.
Submitted by: luigi
Approved by: netchild (mentor)
- Added new codec id for CX20468-21 and VIA1617A.
Submitted by: Chen Lihong <lihong.chen@gmail.com>
- Re-enable SOUND_MIXER_IGAIN, but set the default level as 0 (mute)
Suggested by: luigi
mixer.c:
- Set default value for SOUND_MIXER_IGAIN as 0 (mute) to avoid
feedback problems on some laptops (was disabled by jhb during
ac97.c revision 1.42).
Approved by: netchild (mentor)
erratic system slowdown (beaten to a pulp) and possible panic. This
issue has bugged me for as long as I could remember, until I
realized that it is possible for register base offset to hold zero
value which is definitely a "FALSE".
Approved by: netchild (mentor)
compatible AC97 codec.
- As the driver supports so many variants, create a table ids for
ease of probing and maintenance.
Submitted by: yongari
Reviewed/Tested by: multimedia@
- From luigi:
The code to compute fragment sizes in the ich driver almost
invariably ends up using the full buffer available, no matter
how the user specifies fragment size and number.
With audio telephony (8khz, 16bit-stereo) and the 16k buffer
size this results in an unbearable 500ms delay.
This patch makes sure that we never use more than 4 fragments,
(i don't think we need more unless there are huge interrupt
servicing latencies), and obey to the requested fragment size,
so that latency is acceptable.
Based on this (and after much regression tests), I can conclude
that this driver works best with 2 fragments, thus solving various
long standing issues of ICH driver not capable to flush or play
short files perfectly.
Suggested by: luigi (the idea of smaller fragments)
- MPSAFE conversion.
Approved by: netchild (mentor)
distinct hardware playback channels. DAC configuration can be
accessed through kernel hint - hint.pcm.<unit>.dac="val" with
following possible values:
0 = Enable both DACs (default)
1 = Enable single DAC (DAC1)
2 = Enable single DAC (DAC2)
3 = Enable both DACs, swap position (DAC2 comes first instead
of DAC1)
Special case for ES1370:
Unlike ES1371,2,3/CT5880, volume for each DAC 1 and 2 can be
controlled indepedently (synth for DAC1, pcm for DAC2). It is
possible that user will confuse by this behaviour, since both
DACs are enabled by default. Thus, provide a knob through sysctl
hw.snd.pcm<unit>.single_pcm_mixer:
0 = each DACs will be controlled separately (synth/pcm).
1 = combine both DACs volume mixer controller into a single
"pcm" (default)
As a side note, fixed rate operation (provided by previous
commit) is not a mandatory if the configuration space does not
involve DAC2 (perhaps disabled by user through the above kernel
hint). Unlike DAC2, DAC1 has its own register / control space,
not affected by the speed settings of ADC.
Tested by: multimedia@
Approved by: netchild (mentor)
mask to recdev_l and recdev_r, since each have its own unique mask.
Submitted by: Watanabe Kazuhiro <CQG00620@nifty.ne.jp>
Approved by: netchild (mentor)
just discard the received frame and reuse the old mbuf.
This should prevent the connection from stalling after high network traffic.
MFC after: 2 weeks
a new mbuf, just discard the received frame and reuse the old mbuf.
This should fix kernel panics on high network traffic.
Obtained from: NetBSD (joerg@)
MFC after: 2 weeks
It may be the case that you may hear some unwanted noise while
playing back with 24/32 bit. This is a problem in the USB system.
Explanation from Hans Petter Selasky:
---snip---
The current USB sound driver only uses one isochronous
buffer, that is restarted when it is completed. This will lead to a short
period of time, +1ms, where no sound data is sent to the external USB device.
Depending on the load of your computer, this can be as much as 50ms. So the
USB sound driver must use 2 isochronous transfers. At the beginning one will
queue both. Then these are restarted on completion. This will result in a
constant-rate data stream to the external sound device, a minimum sound
buffer equal to the size of the isochronous buffer, and possibly the sound
will reach your ears with less delay. Little delay is a result of constant
data rate. Currently only my USB driver will support that. If one tries that
with the USB driver in *BSD, then it will crash at the first moment one gets
a buffer underrun.
---snip---
Submitted by: Kazuhito HONDA <kazuhito@ph.noda.tus.ac.jp>
Mono-recording still not tested by: julian
- several TerraTec TValue [1]
- PixelView PlayTV Pro REV-4C [2]
In case you have the PixelView card, please tell us the "pciconf -v -l"
output on multimedia@FreeBSD.org if it works. There are revisions out there
which may not work and we need to know which ones work.
PR: 53383 [1], 76002 [2]
Submitted by: Tanja Wittke <tawi@gruft.de> [1], barner [1],
Dan Angelescu <mrhsaacdoh@yahoo.com> [2]
MFC after: 2 months
This is the only file of > 1700 files in a buildkernel here doing that.
It makes reproducible builds (same source => same binary) impossible.
Spotted by: devel/ccache
from the printer and discarding the data even if the ulpt device
was opened for reading. This resulted in crashes because two
conconcurrent read transfers were using the same transfer structure.
PR: usb/88886
Reported By: Alex Pivovarov
MFC after: 1 week
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
The following repo-copies were made (by Mark Murray):
sys/i386/isa/spkr.c -> sys/dev/speaker/spkr.c
sys/i386/include/speaker.h -> sys/dev/speaker/speaker.h
share/man/man4/man4.i386/spkr.4 -> share/man/man4/spkr.4
copy of Ethernet address.
- Change iso88025_ifattach() and fddi_ifattach() to accept MAC
address as an argument, similar to ether_ifattach(), to make
this work.
overruns and number of watchdog timeouts.
- Do not log(9) RX overrun events, since this pessimizes
things under load [1].
- Do not increase if->if_oerrors in em_watchdog(), since
this leads to counter slipping back, when if->if_oerrors
is recalculated in em_update_stats_counters(). Instead
increase watchdog counter in em_watchdog() and take it
into account in em_update_stats_counters().
Submitted by: ade [1]
- disable jumbo frame support on strict alignment architectures due
to the limitation of hardware. The driver needs a fix-up code for
RX side. The fix will show up in near future.
- fix endian issue for 82544 on PCI-X bus. I couldn't test this as
I don't have the NIC/hardware.
- prefer PCIR_BAR to hardcoded EM_MMBA.
- Properly checks for for 64bit BAR [1]
- replace inl/outl with bus_space(9) [1]
- fix endian issue on VLAN handling.
- reorder header files and remove unnecessary one.
Reviewed by: cognet
No response from: pdeuskar, tackerman
Obtained from: OpenBSD [1]
the RocketPort unit number in the name of the devices. This means that
unit 0 device names will change from ttyR0 .. ttyRf to ttyR00 .. ttyR0f.
Reviewed by: phk
acpi_resource change was a minor nit offered as an early candidate for
the recent ACPICA import problem and the acpi.c change is one I need to
test still that makes the ordered probing of system devices actually work
as advertised (probe devices in order based on the type of device rather
than in the order we encounter them in the device tree).
entry that is not zero, assume that it is really a hard-wired IRQ (commonly
used for APIC routing) and not a source index. In practice, we've only
ever seen source indices of 0 for legitimate non-hard-wired _PRT entries.
Reviewed by: njl
Tested by: Alex Lyashkov shadow at psoft dot net
MFC after: 2 weeks
Intel's web site requires some minor tweaks to get it to work:
- The driver seems to have been released with full WMI tracing enabled,
and makes references to some WMI APIs, namely IoWMIRegistrationControl(),
WmiQueryTraceInformation() and WmiTraceMessage(). Only the first
one is ever called (during intialization). These have been implemented
as do-nothing stubs for now. Also added a definition for STATUS_NOT_FOUND
to ntoskrnl_var.h, which is used as a return code for one of the WMI
routines.
- The driver references KeRaiseIrqlToDpcLevel() and KeLowerIrql()
(the latter as a function, which is unusual because normally
KeLowerIrql() is a macro in the Windows DDK that calls KfLowewIrql()).
I'm not sure why these are being called since they're not really
part of WDM. Presumeably they're being used for backwards
compatibility with old versions of Windows. These have been
implemented in subr_hal.c. (Note that they're _stdcall routines
instead of _fastcall.)
- When querying the OID_802_11_BSSID_LIST OID to get a BSSID list,
you don't know ahead of time how many networks the NIC has found
during scanning, so you're allowed to pass 0 as the list length.
This should cause the driver to return an 'insufficient resources'
error and set the length to indicate how many bytes are actually
needed. However for some reason, the Intel driver does not honor
this convention: if you give it a length of 0, it returns some
other error and doesn't tell you how much space is really needed.
To get around this, if using a length of 0 yields anything besides
the expected error case, we arbitrarily assume a length of 64K.
This is similar to the hack that wpa_supplicant uses when doing
a BSSID list query.
for code to start out on one CPU when thunking into Windows
mode in ctxsw_utow(), and then be pre-empted and migrated to another
CPU before thunking back to UNIX mode in ctxsw_wtou(). This is
bad, because then we can end up looking at the wrong 'thread environment
block' when trying to come back to UNIX mode. To avoid this, we now
pin ourselves to the current CPU when thunking into Windows code.
Few other cleanups, since I'm here:
- Get rid of the ndis_isr(), ndis_enable_interrupt() and
ndis_disable_interrupt() wrappers from kern_ndis.c and just invoke
the miniport's methods directly in the interrupt handling routines
in subr_ndis.c. We may as well lose the function call overhead,
since we don't need to export these things outside of ndis.ko
now anyway.
- Remove call to ndis_enable_interrupt() from ndis_init() in if_ndis.c.
We don't need to do it there anyway (the miniport init routine handles
it, if needed).
- Fix the logic in NdisWriteErrorLogEntry() a little.
- Change some NDIS_STATUS_xxx codes in subr_ntoskrnl.c into STATUS_xxx
codes.
- Handle kthread_create() failure correctly in PsCreateSystemThread().
since the link takes a bit to negotiate, the information is pretty
much never available during the probe. As such, the boot output
pretty much always prints N/A for speed and duplex. Since we print
out the output of ifconfig during the user space boot, this early
boot information is also generally redundant, and added to the noise.
MFC after: 2 weeks
- Prefer '_' to ' ', as it results in more easily parsed results in
memory monitoring tools such as vmstat.
- Remove punctuation that is incompatible with using memory type names
as file names, such as '/' characters.
- Disambiguate some collisions by adding subsystem prefixes to some
memory types.
- Generally prefer lower case to upper case.
- If the same type is defined in multiple architecture directories,
attempt to use the same name in additional cases.
Not all instances were caught in this change, so more work is required to
finish this conversion. Similar changes are required for UMA zone names.
in bytes to start off with. This caused the GPT geom sniffer to attempt
a seek just back from the end of the 'disk', which resulted in a > 4G
seek, causing gdb psim to exit since it only supports 32-bit seeks.
The size of the disk should really be specified in the psim device tree,
but for now do the minimal amount of work to get psim to run again.
aac_alloc_sync_fib(). aac_alloc_sync_fib() will assert that the I/O locks
are held. This fixes a panic on system boot up when the aac(4) device's
bus_generic_attach() routine is called.
Reviewed by: scottl
- Return EINVAL if play_format or rec_format is set but the corresponding
sample rate is 0.
- Don't try to set the playback or recording format to 0. Previously,
issuing an AIOSFMT ioctl with an all-zeroes snd_chan_param would
trigger a KASSERT in chn_fmtchain(); I'm unsure about the effects on
a kernel without INVARIANTS. After this commit, issuing AIOSFMT with
an all-zeroes snd_chan_param is equivalent to issuing AIOGFMT.
MFC after: 2 weeks
actual resource values we received from the system rather than the range
we requested. Since we request a range starting at 0, we would record
that number. Later, since this == 0, we'd allocate again. However,
we wouldn't write the new resource into the BAR. This resulted in
a resource leak as well as a BAR that couldn't access the resource at
all since rman_get_start, et al, were wrong.
MFC After: 1 week (assuming RELENG_6 is open for business)
the ifp, so you can't call it before doing if_alloc(). Also, there's
really no need to call it here anyway: the code I originally ported from
OpenBSD incorrectly set the station address only once at device attach
time, instead of setting in txp_init(). This meant you couldn't change
the address with ifconfig txp0 ether xx:xx:xx:xx:xx:xx. I added the
call to txp_set_filter() in txp_init() to correct this, but forgot to
remove the call from txp_attach(). Until now, it never mattered.
With this fix, the txp driver tests good:
txp0: <3Com 3cR990-TX-97 Etherlink with 3XP Processor> port 0xb800-0xb87f mem 0xe6800000-0xe683ffff irq 12 at device 10.0 on pci0
txp0: Ethernet address: 00:01:03:d4:91:4f
and channel to ifconfig. Also use the SSID and channel info from
the association info that we already have instead of using ndis_get_info()
to ask the driver for it again.
o Fix typo in comment
o s/-100/BUS_PROBE_GENERIC/
o s/err/error/ for consistency
o Remove non-applicable comment
o Allow uart_bus_probe() to return the predefined BUS_PROBE_*
contants. In this case: explicitly test for error > 0.
I had to initialize the ifnet a bit earlier in attach so that the
if_printf()'s in vr_reset() didn't explode with a page fault.
- Use M_ZERO with contigmalloc() rather than an explicit bzero.
even initialized it, but it never used it.
- Use callout_*() to manage the callout.
- Use m_devget() to copy data out of the rx buffers rather than doing it
all by hand.
- Use m_getcl() to allocate mbuf clusters rather than doing it all by hand.
- Don't free the software descriptor for a rx ring entry if we can't
allocate an mbuf cluster for it. We left a dangling pointer and never
reallocated the entry anyway. OpenBSD's code (from which this was
derived) has the same bug.
Tested by: NO ONE (despite repeated requests)
Reviewed by: wpaul (5)
o Oxford Semiconductor PCI Dual Port Serial
o Netmos Nm9845 PCI Bridge with Dual UART
Add PCI IDs for single-port cards:
o Various SIIG Cyber Serial
o Oxford Semiconductor OXCB950 UART
Update description as per puc(4).
