Use the drop and enable endpoint context commands to force a reset of
the data toggle for USB 2.0 and USB 3.0 after:
- clear endpoint halt command (when the driver wishes).
- set config command (when the kernel or user-space wants).
- set alternate setting command (only affected endpoints).
Some XHCI HW implementations may not allow the endpoint reset command when
the endpoint context is not in the halted state.
Reported by: Juniper and Gary Jennejohn
MFC after: 1 week
Sponsored by: NVIDIA Networking
The result of the request computed in new_status was never returned to
the caller leaving new_status as a set-but-unused variable. Removing
new_status leaves sc->previous_status as a write-only variable.
Removing sc->previous_status leaves current_status as a write-only
variable, so it collapses down to removing the entire
USB_ST_TRANSFERRED case.
Arguably, all of the support for UHID_SNES_STATUS_DT_RD should be
removed as it doesn't return anything to the caller. If the request
should be fixed instead then this commit should be reverted and
new_status should be returned to whoever submitted the request.
Differential Revision: https://reviews.freebsd.org/D34840
This should fix an issue where the "udev->re_enumerate_wait" field never gets
processed and reset. In this case usbconfig will wait forever and never return.
MFC after: 1 week
Sponsored by: NVIDIA Networking
This command is intended to be compatible with USB_REQUEST ioctl.
It is required to perform arbitrary control endpoint requests by device
drivers which can switch between HID and native non-HID modes.
MFC after: 2 month
Add support for printing ACPI paths. This is a bit of a degenerate case
for this interface since it's always just the device handle if the
device has one. But it is illustrtive of how to do this for a few nodes
in the tree.
Sponsored by: Netflix
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D32748
Currently there are five quirks the USB stack tries to automagically detect:
- UQ_MSC_NO_PREVENT_ALLOW
- UQ_MSC_NO_SYNC_CACHE
- UQ_MSC_NO_TEST_UNIT_READY
- UQ_MSC_NO_GETMAXLUN
- UQ_MSC_NO_START_STOP
If any of the quirks above are set, no further quirks will be probed.
If any of the USB mass storage tests fail, the USB device is
re-enumerated as a last resort to clear any error states from the
device. Then the USB stack will try to probe and attach the umass<N>
device passing the detected quirks.
While at it give more details in dmesg about what is going on.
Tested by: several
Submitted by: Idwer Vollering <vidwer_fbsdbugs@gmail.com>
Differential Revision: https://reviews.freebsd.org/D30919
MFC after: 1 week
Sponsored by: NVIDIA Networking
EXT_RESOURCES have been introduced in 12-CURRENT and all supported
releases have it enabled in their kernel config.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D33827
If port resume fails, likely the USB device is detached. Ignore such errors,
because else the USB stack might try forever trying to resume the device,
before it will proceed detaching it.
MFC after: 1 week
Sponsored by: NVIDIA Networking
The USB controller drivers assume they can cast a NULL pointer to a
struct and find the address of a member. KUBSan complains about this so
replace with the __offsetof and __containerof macros that use either a
builtin function where available, or the same NULL pointer on older
compilers without the builtin.
Reviewers: hselasky
Subscribers: imp
Reviewed by: hselasky
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D33865
The saf1761 OTG support was only for mips targets (BERI?). Retire it.
Sponsored by: Netflix
Reviewed by: brooks
Differential Revision: https://reviews.freebsd.org/D33706
