but it's no longer a part of the base-system and buildworld works fine
here after deleting them both on disk and from the mtree spec files.
Not objected to by: kris, silence on -audit
devd later in the boot process. This should fix all the problems
people have had with those commits. Diskless should be working again,
and those that mount /usr with nfs should be able to do that again too.
critical remote systems. This lets us run commands from devd that
aren't on the / partition. This also means we can remove some kludges
from the networking startup that I added a while ago that caused other
problems.
There's still a race in starting devd that needs to be fixed in devd
so that things present at boot will be configured by the time devd
does daemon(). That race will be fixed later.
device node exists directly to see if OLDCARD is compiled into the
kernel. This eliminates the scary warning that people using NEWCARD
are seeing when they have pccard_enable=YES in their /etc/rc.conf
files.
be). Using that string leads rc.network to execute:
# sysctl -w vfs.nfs.bufpackets=DEFAULT
vfs.nfs.bufpackets: 4 -> 0
Which isn't what was intended.
PR: conf/31280
MFC after: 3 days
name of the device that it creates. Update /etc/ttys accordingly.
An alias is created for the old name so that old /etc/ttys will continue to
work, but due to aliases being implemented as symlinks in devfs you cannot
login as root when using the alias device.
Discussed with: grehan
withough the $natd_interface having to be explicitly specified on the
command line.
Approved by: markm (mentor)
Submitted by: Aaron D. Gifford <agifford@infowest.com>
PR: conf/47024
MFC: upon re approval
named(8) daemon by providing a new rc.conf knob: named_pidfile
that defaults to the path specified in the system-installed named.conf(5).
Approved by: markm (mentor)
Reviewed by: dougb
Noticed by : Galen Sampson <galen_sampson@yahoo.com>
Dan Pelleg <daniel+bsd@pelleg.org>
PR: conf/46402
MFC: 2 weeks (with re@ approval)
to /dev/raidctl, don't set the group to operator. (This isn't a
storage device, it's a control device).
Also, since umask here is already restrictive, we don't need to
explicitly set the mode.
Submitted by: bde
Instead, load them as part of the rc.d system. This allows us to prioritize
the initidiskless script so it runs before the configuration files are loaded
and allows us to get rid of the exit 2 hack in /etc/rc. The exit 2 never
worked anyway since it did not unset the prior configuration, causing the
diskless code to not operate properly.
Do a major cleanup and revamping of the diskless code for RCNG. This will
be backported to the non-RCNG scripts as well as -stable.
With suggestions from: Mike Makonnen <mtm@identd.net>
MFC after: 7 days
the whole thing generic. That is, /conf/base, /conf/default,
/conf/${ipba}, and /conf/${ip} are all handled the same way.
Introduce an NFS remounting feature via the /conf/base/<dir>/diskless_remount
so you can avoid dup'ing system directories in /conf (described in rc file).
Introduce a memory filesystem sizing feature via the /conf/base/<dir>/md_size
file that allows you to override the default memory filesystem size.
Introduce a file containing relative paths to remove for each memory filesystem
directory as /conf/base/<dirname>.remove.
Make the cpio feature more generic (applies to any filesystem) (aka
/conf/base/<dirname>.cpio.gz).
Allow any root directories to be created as a memory filesystem via the
/conf/*/* mechanism.
Replace the copyright notice with a reference to the COPYRIGHT file and
do other cleanups.
(documentation and man page updates to follow).
MFC after: 3 days
background fsck. The delay defaults to sixty seconds to allow
large applications such as the X server to start before disk I/O
bandwidth is monopolized by fsck.
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
Sponsored by: DARPA & NAI Labs.
from "unix" back to "local". Add some compat stuff so both
ways work for some time.
Reviewed by: phk
Approved by: imp (UPDATING)
Requested by: iedowse, lukem@netbsd.org
that's being replaced here. This is what /etc/rc does now.
There is no NetBSD devfs, so there is no compatibility issue.
Not objected to by: FreeBSD-rc@yahoogroups.com
Approved by: re (murray)
where people want to have the cards configured. Lack of -z is a speed
optimization.
Submitted by: many voices on mobile@
Approved by: re@ (rwatson)
MFC after: 3 days
Fix a minor grammer nit.
Get rid of _echo that uses logger and just call logger in the 3 routines
that need it.
Add a comment referencing rc.conf(5) in the case of an incorrectly set
variable.
This pulls rc.subr up to 1.51 of rc.subr. I skipped 1.49 (systrace support)
since I don't have systrace.
Obtained from: NetBSD
to specify rules definition file for ipfilter. The default is
/etc/ipf6.rules. If there is a file which is specified by
'ipv6_ipfilter_rules', IPv6 rule is installed.
Reviewed by: Ronald van der Pol <Ronald.vanderPol@rvdp.org>
MFC after: 1 week
an entry in /etc/sysctl.conf didn't exist. Fixing this exposed a minor
typo "exits" vs. "exist".
However, there doesn't appear to be any provision to run this with
the "lastload" argument, meaning that the error will never appear.
whatever random value was already in $unit. It happened to work
because the variable is often unset, but this is not always the
case e.g. when you call "MAKEDEV sio2 usb ..."
This affects -stable as well.
Reviewed by: n_hibma
Silence from: re
MFC after: 3 days
# or any login.conf resource limits or features; use it only if this is
# appropriate for your environment. If you require these features, use
# the regular FreeBSD ftpd below.
Discourage users from using lukemftpd if they rely any of these standard
FreeBSD features that are fully supported by our native ftpd. There
may be other features that are not yet supported that I have not yet
discovered.
tells applications to print labels for all of the TrustedBSD-
generated policies, if they are present.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
the wheel group has no explicit members listed in /etc/group. This adds
the "exempt_if_empty" flag to pam_wheel in the default configuration;
in some environments, it may be appropriate to remove this flag, however,
this default is the same as pre-pam_wheel.
Reviewed by: markm
Sponsored by: DARPA, Network Associates Laboratories
configuration. Root privileges override DAC on local file systems and
therefore root does not generally need to be a member of a group to
access files owned by that group. In the NFS case, require explicit
authorization for root to have these privileges.
Leave root in operator for dump/restore broadcast reasons; leave root
in wheel until discrepencies in the "no users in wheel means any user
can su" policy are resolved (possibly indefinitely).
* Space -> tabs conversion.
* Removed blanks before semicolon in "if ... ; then".
* Proper indentation of misindented lines.
* Put a full stop after some comments.
* Removed whitespace at end of line.
Approved by: silence from gordon
script did. Stuff in rc.local frequently has lines like
"echo -n ' service_name'" which look ugly without a prefix and a
trailing period. Likewise for rc.shutdown.local for consistency.
and atime only, but also the ctime. Otherwise, files extracted from
tar or zip archives will immediately be declared stale since they've
got their mtime reset to the original mtime.
Reviewed by: brian
MFC after: 1 week
a per-machine or per-cluster (with different ways of expressing what's
part of a cluster) basis. In order for this to be effective, rc.conf
has to be reread after initdiskless is finished. Implement this by
adding a hook to etc/rc which rereads rc.conf by request. This can
also be implemented by renaming initdiskless to initdiskless.sh and
sourcing rc.conf there manually, but it was decided that, that would
be uglier than a hook in etc/rc.
Developed in concert with: gordon
PR: 38919
Submitted by: Tommy Johnson
o IBM IDE CDROM
PR: 39537
Submitted by: Kevin Van Maren
o T-Sunus 130 card
PR: 41802
Submitted by: Oliver Schneider
o No-name OEM Prism card
o ActionTec Prism card
o ZoomAir 11Mbps High Rate wireless networking
PR: 41929, 41928
Submitted by: Bruce M Simpson
o Dynalink L100C16
PR: 41938
Submitted by: Marco van de Voort
1) Add new card entry for nortel eMobility wi card (from email
that I've lost the sender on :-(
2) put ata devices at config 0x1 rather than auto. This should be
better for nearly all cases.
MFC after: 3 days
rcNG. The $amd_flags variable was already taken over into $rc_flags
by run_rc_command() when amd_precmd() is executed, so changing
$amd_flags there no longer effects the actual execution of amd.
Hence in amd_precmd() the $rc_flags have to be adjusted instead.
o Recognize AMD Elan SC520 hostbridge.
o Add initialization code for the AMD Elan sc520 which maps the MMCR
into KVM and sets the i8254 frequency to the correct value.
o MAKEDEV entry for elan-mmcr device
Reviewed by: phk, jhb
Approved by: re(jhb)
under way to move the remnants of the a.out toolchain to ports. As the
comment in src/Makefile said, this stuff is deprecated and one should not
expect this to remain beyond 4.0-REL. It has already lasted WAY beyond
that.
Notable exceptions:
gcc - I have not touched the a.out generation stuff there.
ldd/ldconfig - still have some code to interface with a.out rtld.
old as/ld/etc - I have not removed these yet, pending their move to ports.
some includes - necessary for ldd/ldconfig for now.
Tested on: i386 (extensively), alpha
all instances of `${CMD_OSTYPE}` to just using ${OSTYPE}. This saves us a
shell invocation on anything that is OS-dependent. I seriously doubt that we
will be spontaneously changing OS types during bootup.
in the script. Eliminates a bug where we create a temp file, but don't
delete it since the rm(1) is only done if the check is enabled.
PR: bin/40960
Submitted by: frf <frf@xocolatl.com>
MFC after: 3 days
xntpd_* -> ntpd_*
portmap_* -> rpcbind_*
Also change single_mountd_enable -> mountd_enable
Changing the mountd flags brings us closer to NetBSD.
All of the old variable names are shimmed so you can continue to use the
old variable name.
Finally make /etc/rc.d/mountd no longer dependent on nfs as there are
(apparently) other consumers of mountd.
Submitted by: Mike Makonnen <makonnen@pacbell.net>
xntpd_* -> ntpd_*
portmap_* -> rpcbind_*
Also change single_mountd_enable to mountd_enable.
We also include shims for all the old variable names.
Submitted by: Mike Makonnen <makonnen@pacbell.net>
and others, because test(1) does not do shortcut evaluation.
Fix the same off-by-one error for acd*t* that revision 1.326 fixed
for other *cd devices.
Suggested by: bde
Reviewed by: bde
created cd1 as well due to an off-by-one error left over from
revision 1.249.
PR: conf/20436
Submitted by: Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
MFC after: 1 week
MP=`mount -t ufs | grep -v " nosuid" | awk '{ print $3 }' | sort`
sets ${MP} to an empty string so the next line:
set ${MP}
actually just dumps all of the shells variables to stdout (and therefore
the security report). Fixed by surrounding the code which goes through the
mounts with a test for an empty string before using ${MP}.
Reviewed by: brian
MFC after: 3 days
/etc filesystem isn't enough; consequently, add "-i 4096" to the newfs
command for /etc. This results in 1022 inodes, which should be enough
for the forseeable future (although I don't know why we would ever
have more than 1000 files in a default /etc).
Silence by: -current
Submitted by: matt peterson
While I'm here, kill the flags 0x10000 on all the prism based cards.
Both stable and current figure this out on their own and we've had at
least one releases where this is the case.
card behind it (without the pcmcia form factor). This entry gets to
the point of attaching, but there's something wrong with the '29
support, so it doesn't quite work yet.
while. This is only the script pieces, the glue for the build comes next.
Submitted by: Mike Makonnen <makonnen@pacbell.net>
Reviewed by: silence on -current and -hackers
Prodded by: rwatson
Once upon a time (in rev. 1.81), COPYRIGHT and FREEBSD
were multi-value.
Moved installation of /var/log/cron to where it belongs
(this finishes the change in rev. 1.205).
Removed (with extreme prejudice) a bunch of parentheses
that unnecessarily obfuscated this makefile.
Run pwd_mkdb(8) right after master.passwd is installed.
Install nsmb.conf to /usr/share/examples/etc/.
MAKEDEV: Add MAKEDEV glue for the ti(4) device nodes.
ti.4: Update the ti(4) man page to include information on the
TI_JUMBO_HDRSPLIT and TI_PRIVATE_JUMBOS kernel options,
and also include information about the new character
device interface and the associated ioctls.
man9/Makefile: Add jumbo.9 and zero_copy.9 man pages and associated
links.
jumbo.9: New man page describing the jumbo buffer allocator
interface and operation.
zero_copy.9: New man page describing the general characteristics of
the zero copy send and receive code, and what an
application author should do to take advantage of the
zero copy functionality.
NOTES: Add entries for ZERO_COPY_SOCKETS, TI_PRIVATE_JUMBOS,
TI_JUMBO_HDRSPLIT, MSIZE, and MCLSHIFT.
conf/files: Add uipc_jumbo.c and uipc_cow.c.
conf/options: Add the 5 options mentioned above.
kern_subr.c: Receive side zero copy implementation. This takes
"disposable" pages attached to an mbuf, gives them to
a user process, and then recycles the user's page.
This is only active when ZERO_COPY_SOCKETS is turned on
and the kern.ipc.zero_copy.receive sysctl variable is
set to 1.
uipc_cow.c: Send side zero copy functions. Takes a page written
by the user and maps it copy on write and assigns it
kernel virtual address space. Removes copy on write
mapping once the buffer has been freed by the network
stack.
uipc_jumbo.c: Jumbo disposable page allocator code. This allocates
(optionally) disposable pages for network drivers that
want to give the user the option of doing zero copy
receive.
uipc_socket.c: Add kern.ipc.zero_copy.{send,receive} sysctls that are
enabled if ZERO_COPY_SOCKETS is turned on.
Add zero copy send support to sosend() -- pages get
mapped into the kernel instead of getting copied if
they meet size and alignment restrictions.
uipc_syscalls.c:Un-staticize some of the sf* functions so that they
can be used elsewhere. (uipc_cow.c)
if_media.c: In the SIOCGIFMEDIA ioctl in ifmedia_ioctl(), avoid
calling malloc() with M_WAITOK. Return an error if
the M_NOWAIT malloc fails.
The ti(4) driver and the wi(4) driver, at least, call
this with a mutex held. This causes witness warnings
for 'ifconfig -a' with a wi(4) or ti(4) board in the
system. (I've only verified for ti(4)).
ip_output.c: Fragment large datagrams so that each segment contains
a multiple of PAGE_SIZE amount of data plus headers.
This allows the receiver to potentially do page
flipping on receives.
if_ti.c: Add zero copy receive support to the ti(4) driver. If
TI_PRIVATE_JUMBOS is not defined, it now uses the
jumbo(9) buffer allocator for jumbo receive buffers.
Add a new character device interface for the ti(4)
driver for the new debugging interface. This allows
(a patched version of) gdb to talk to the Tigon board
and debug the firmware. There are also a few additional
debugging ioctls available through this interface.
Add header splitting support to the ti(4) driver.
Tweak some of the default interrupt coalescing
parameters to more useful defaults.
Add hooks for supporting transmit flow control, but
leave it turned off with a comment describing why it
is turned off.
if_tireg.h: Change the firmware rev to 12.4.11, since we're really
at 12.4.11 plus fixes from 12.4.13.
Add defines needed for debugging.
Remove the ti_stats structure, it is now defined in
sys/tiio.h.
ti_fw.h: 12.4.11 firmware.
ti_fw2.h: 12.4.11 firmware, plus selected fixes from 12.4.13,
and my header splitting patches. Revision 12.4.13
doesn't handle 10/100 negotiation properly. (This
firmware is the same as what was in the tree previously,
with the addition of header splitting support.)
sys/jumbo.h: Jumbo buffer allocator interface.
sys/mbuf.h: Add a new external mbuf type, EXT_DISPOSABLE, to
indicate that the payload buffer can be thrown away /
flipped to a userland process.
socketvar.h: Add prototype for socow_setup.
tiio.h: ioctl interface to the character portion of the ti(4)
driver, plus associated structure/type definitions.
uio.h: Change prototype for uiomoveco() so that we'll know
whether the source page is disposable.
ufs_readwrite.c:Update for new prototype of uiomoveco().
vm_fault.c: In vm_fault(), check to see whether we need to do a page
based copy on write fault.
vm_object.c: Add a new function, vm_object_allocate_wait(). This
does the same thing that vm_object allocate does, except
that it gives the caller the opportunity to specify whether
it should wait on the uma_zalloc() of the object structre.
This allows vm objects to be allocated while holding a
mutex. (Without generating WITNESS warnings.)
vm_object_allocate() is implemented as a call to
vm_object_allocate_wait() with the malloc flag set to
M_WAITOK.
vm_object.h: Add prototype for vm_object_allocate_wait().
vm_page.c: Add page-based copy on write setup, clear and fault
routines.
vm_page.h: Add page based COW function prototypes and variable in
the vm_page structure.
Many thanks to Drew Gallatin, who wrote the zero copy send and receive
code, and to all the other folks who have tested and reviewed this code
over the years.
which needs an empty directory into which to chroot(2).
Hint to the operator that this directory really _should_ be empty
by creating it with mode 0555 and the system immutable flag (schg)
set.
Reviewed by: des
while. This is only the script pieces, the glue for the build comes next.
Submitted by: Mike Makonnen <makonnen@pacbell.net>
Reviewed by: silence on -current and -hackers
Prodded by: rwatson
permissions to use for alias and map database files built by
/etc/mail/Makefile. The default is 0640 to assist users in avoiding
a file locking local denial of service.
MFC after: 1 day
pending RE approval
Apparently binding only to 127.0.0.1 inside of a jail actually binds
to the jail IP address as well (in effect, bind to all available
interfaces in the jail).
Submitted by: Helge Oldach <test-smtp@oldach.net>
MFC after: 1 day
pending RE approval
though I would personally prefer to see the broken nameservers fixed
instead of standards compliant applications work around them, I can't
force FreeBSD users to help fight that battle.
Submitted by: Damon Anton Permezel <dap@damon.com>
MFC after: 2 days
pending RE approval
fix a comment that suggested setting ipv6_ipv4mapping to blank. This
will aid in merging with rcng which requires all veriables to be
explicitly set.
Submitted by: Mike Makonnen
MFC after: 1 week
files in each ${local_startup} directory, it also reverses the order of the
directories.
Suggested by: jhb
Reviewed by: jake
Approved by: dougb
MFC after: 1 week
of wtmp.0 is done as mode 600.
This ensures that tight permissions set in /etc/newsyslog.conf for
wtmp logging aren't ``betrayed''.
Suggested by: lumpy <lumpy@the.whole.net>
MFC after: 3 days
The change was introduced in src/etc/security 1.53 almost a year ago
in an attempt to see ipfw deny message logs.
However, ipfw deny/reject logs have been displayed since version 1.13
of the same file as a separate ``job'' and have since moved to
src/etc/periodic/security/500.ipfwdenied.
MFC after: 3 days
rm -f /tmp/.X11-unix/*
If /tmp/.X11-unix didn't already exist, a user could symlink it to a directory
with files that he wants to wipe out, and wait for next reboot.
Reported by: lumpy <lumpy@the.whole.net>
The Blue Concentric CF 802.11b card is a compactflash form-factored card
that does 802.11b, including 128bit encryption.
The Zonet modem pccard is a simple FAX/Modem card.
Both are sold in Guang-Hua Market in Taipei, and functions perfectly
with -current and -stable.
Due to the way we run ls(1), through xargs(1), the leading whitespace
can change even when the setuid files haven't. To avoid displaying
these lines, we currently run diff(1) with the '-w' option. However,
this is probably not the ideal way to go; there is a very, very small
possibility for diff(1) to miss things is shouldn't. So, with the
leading space cleaned, we can revert to the '-b' option which is
"safer."
PR: conf/37618
Reviewed by: brian
MFC after: 3 days
pam_lastlog, so add a dummy session chain to avoid using the one from
pam.d/other. I assume gdm does something similar, so give it a dummy
session chain as well.
Sponsored by: DARPA, NAI Labs.
Do not install games and profiled libraries to the ${CHROOTDIR}
with the initial installworld.
Eliminate the need in the second installworld. For that, make sure
_everything_ is built in the "world" environment, using the right
tool chain.
Added SUBDIR_OVERRIDE helper stuff to Makefile.inc1. Split the
buildworld process into stages, and skip some stages when
SUBDIR_OVERRIDE is set (used to build crypto, krb4, and krb5
dists).
Added NO_MAKEDB_RUN knob to Makefile.inc1 to avoid running
makewhatis(1) at the end of installworld (used when making crypto,
krb4, and krb5 dists).
In release/scripts/doFS.sh, ensure that the correct boot blocks are
used.
Moved the creation of the "crypto" dist from release.5 to
release.2.
In release.3 and doMFSKERN, build kernels in the "world"
environment. KERNELS now means "additional" kernels, GENERIC is
always built.
Ensure we build crunched binaries in the "world" environment.
Obfuscate release/Makefile some more (WMAKEENV) to achieve this.
Inline createBOOTMFS target.
Use already built GENERIC kernel modules to augment mfsfd's
/stand/modules. GC doMODULES as such.
Assorted fixes:
Get rid of the "afterdistribute" target by moving the single use
of it from sys/Makefile to etc/Makefile's "distribute".
Makefile.inc1: apparently "etc" no longer needs to be last for
"distribute" to succeed.
gnu/usr.bin/perl/library/Makefile.inc: do not override the
"install" and "distribute" targets, do it the "canonical" way.
release/scripts/{man,cat}pages-make.sh: make sure Perl manpages and
catpages appear in the right dists. Note that because Perl does
not respect the MANBUILDCAT (and NOMAN), this results in a loss of
/usr/share/perl/man/cat* empty directories. This will be fixed
soon.
Turn MAKE_KERBEROS4 into a plain boolean variable (if it is set it
means "make KerberosIV"), as documented in the make.conf(5)
manpage. Most of the userland makefiles did not test it for "YES"
anyway.
XXX Should specialized kerberized libpam versions be included into
the krb4 and krb5 dists? (libpam.a would be incorrect anyway if
both krb4 and krb5 dists were choosen.)
Make sure "games" dist is made before "catpages", otherwise games
catpages settle in the wrong dist.
Fast build machine provided by: Igor Kucherenko <kivvy@sunbay.com>
around. If the kernel boots successfully, the record of this kernel
is erased, it is intended to be a one-shot option for testing
kernels.
This could be improved by having the loader remove the record of
the next kernel to boot, it is currently removed in /etc/rc immediately
after disks are mounted r/w.
I'd like to MFC this before the 4.6 freeze unless there is violent
objection.
Reviewed by: Several on IRC
MFC after: 4 days
alternative MTAs. Therefore, always install rc.sendmail, regardless of
NO_SENDMAIL make.conf setting. Users can still set mta_start_script to a
different script.
This commit is after a repo-copy of src/etc/sendmail/rc.sendmail to
src/etc/rc.sendmail.
Noticed by: Calvin NG <calvinng@brel.com>
MFC after: 3 days
the creation of /var/spool/clientmqueue and therefore the need for the
smmsp user and group if NO_SENDMAIL is defined. This required breaking out
the creation of the directory into a new BSD.sendmail.dist mtree file.
MFC after: 1 week
Added NOOBJ if anyone even attempts to "make obj" here.
Revert to installing files with mode 644 except README.
Make this overall look like a BSD-style Makefile rather
than roll-your-own (this is not a bug).
For the record. Previous revision also fixed the breakage
introduced by the sys.mk,v 1.60 commit: bsd.own.mk is no
longer automatically included from sys.mk.
Reported by: jhay
the .mc file used for /etc/mail/submit.cf. By default,
/etc/mail/freebsd.submit.mc is installed and used.
Requested by: fenner
Submitted by: ume
MFC after: 1 week
Add /etc/rc.d to the startup dirs list. It is a convenient place to put
custom startup scripts instead of hacking a shared rc.local. eg: ftpd in
listener mode, or maybe even sendmail or another mailer, etc.
<peril sensitive sunglasses off>
clientmqueue (submit mail queue).
The new mailq display is only active if both the old
daily_status_mailq_enable is set to "YES" and the new
daily_status_include_submit_mailq is set to "YES" so people who disabled
440.status-mailq won't have any surprises.
Likewise, the new queue run is only active if both the old
daily_queuerun_enable is set to "YES" and the new daily_submit_queuerun
is set to "YES" so people who disabled 500.queuerun won't have any
surprises.
While I am here, remove the [ ! -d /var/spool/mqueue ] checks from
both scripts as the queue directory isn't always /var/spool/mqueue for
the main daemon -- it can be set to anything in the sendmail.cf file.
MFC after: 1 week
prevent the interfaces from being initialized by /etc/rc.network6
wrongly. So, you can explicitly initialize the interfaces by
/etc/pccard_ether.
With previous rc.network6, if you specify pccardd_flags="-z",
net.inet6.ip6.accept_rtadv was wronly set to 0, then RA was not
accepted.
again."
As an alternative to sendmail_enable=NONE, solve the boot time problem
for non-sendmail users completely by moving all of the sendmail startup
code from /etc/rc to /etc/rc.sendmail. The source for that script will
be kept in src/etc/sendmail/rc.sendmail so make.conf's NO_SENDMAIL will
prevent it from being installed. A new rc.conf variable,
mta_start_script specifies the script to run to start the user's
preferred MTA. For backward compatibility, it will default to
/etc/rc.sendmail. The specified script is called out of /etc/rc after
checking to make sure it exists. A new rc.sendmail.8 man page has also
been added which now houses the sendmail_* variable descriptions
formerly in rc.conf.5.
Use /etc/rc.sendmail in /etc/mail/Makefile to reduce code duplication.
Reviewed by: -current, -stable, obrien, peter, ru
MFC after: 1 week
was apparently smoking something when I committed the last fix, because as
ume was kindly enough to set me straight on, amd *will* start with no
arguments at all, as long as there is an /etc/amd.conf file for it to
read. What it won't do is start with *just* -p.
In any case, now it's fixed.
(65536 * 32 - 1), but MAKEDEV only supports up to (32 * 32 -1). Device
names use the unit number in base 32 for all "digits".
This required fixing an old bug in MAKEDEV:ttyminor(). Its arg was the
global $unit instead of $1.
Reminded by: Valentin K. Ponomarenko <valka@krog.ukrtel.net>
MFC-after: 1 week
logic and added a new set of targets for controlling the MSP queue runner
(start-mspq, stop-mspq, and restart-mspq).
Reminded by: Mark Santcroos <marks@ripe.net>
MFC after: 1 week
at boot time.
Instead of rc.conf's sendmail_enable only accepting YES or NO, it can now
also accept NONE. If set to NONE, none of the other sendmail related
startup items will be done.
Remove an extra queue running daemon might be started that wasn't necessary
(it didn't hurt anything but it wasn't needed).
The new logic is:
# MTA
if ${sendmail_enable} == NONE
# Do nothing
else if ${sendmail_enable} == YES
start sendmail with ${sendmail_flags}
else if ${sendmail_submit_enable} == YES
start sendmail with ${sendmail_submit_flags}
else if ${sendmail_outbound_enable} == YES
start sendmail with ${sendmail_outbound_flags}
endif
# MSP Queue Runner
if ${sendmail_enable} != NONE &&
[ -r /etc/mail/submit.cf] && ${sendmail_msp_queue_enable} == YES
start sendmail with ${sendmail_msp_queue_flags}
endif
Discussed with: Thomas Quinot <Thomas.Quinot@Cuivre.FR.EU.ORG>,
Christopher Schulte <schulte+freebsd@nospam.schulte.org>
MFC after: 1 week
Install sys/<arch>/include/pc/*.h to /usr/include/machine/pc/.
PR: docs/29534
Install sys/netatm/*/*.h to /usr/include/netatm/*/.
Don't install compatibility symlinks for <machine/soundcard.h>
and <machine/joystick.h>. Three years is enough to be aware of
the change, and these weren't visible in the SHARED=symlinks
case.
Back out include/Makefile,v 1.160 that was a null change anyway
due to the bug in the path, and we now don't want to install
these headers because they would otherwise be invisible in the
SHARED=symlinks case.
Don't install IPFILTER headers. Userland utilities fetch them
directly, and they were not visible in the SHARED=symlinks case.
Resurrect SHARED=symlinks in Makefile.inc1.
PR: bin/28002
Prodded by: bde
MFC after: 2 weeks
black lists in the default config, give a pointer to a non-static list.
I was convinced this was the right thing to do after getting a PR
asking to add ORBZ the day before ORBZ went off the air.
PR: conf/35884
MFC after: 4 days
only doing ipnat(8). Go back to using $ipfilter_active, but turn off
$ipfilter_active when loading ipl.ko has failed.
Submitted by: devet@devet.org (Arjan de Vet)
MFC after: 3 days
conf file, or command line options. I brought this up in PR 12432,
which (ironically) obrien assigned to me after I became a committer. :)
PR: conf/12432
Submitted by: Me
administrator wishes to run commands outside of the PATH, he should
use a full pathname for the executable or set the PATH as appropriate
in any local startup scripts.
PR: misc/35770
addition, take out the checks on the $dumpdev. dumpon(8) behaves well
if given a non-existent filename. It gives a nice error message which
is better rather than the current silent failure.
Reviewed by: des
$ipfilter_active. $ipfilter_enable is set to "NO" if modules fail to
load, and $ipfilter_active can be "YES" when we are not using ipf(8).
MFC after: 3 days
and teach it to look for more general classes of failures, including
SSH login failures. This is similar but not identical to a patch
submitted by aeonflux@synapse.subneural.net.
o Introduce /var/log/authentication.log, which will be the target for
auth.info and authpriv.info by default. Rotate on the same schedule
as most other logs. Create at installation.
o Remove logging of auth.info from /var/log/security.log, which will
return to being only for security feature subsystems (such as ipfw,
and so on).
This creates a special authentication log, which can now be searched
by scripts for authentication events.
argument. Don't fail silently, but let savecore(8) make noise. It
won't behave badly, it doesn't need protection.
At the same time, allow the administrator to have dumpdev enabled
while dumpdir (savecore(8)) is disabled and document how to do it.
PR: conf/35725
systems due to sshd not using the security log class. Tweak syslog.conf
so that /var/log/security also gets a useful set of
authentication-related logging.
Submitted by: aeonflux@synapse.subneural.net
MFC after: 4 weeks
Kerberized CVS (kserver) listens on the same port as normal CVS
(pserver). In /etc/inetd.conf cvs kserver is disabled by default,
but set to listen to the service port 'cvs' which doesn't exist. It
should listen to 'cvspserver'.
PR: 34317
Submitted by: Sean Chittenden <sean@chittenden.org>
seperate the short name and the long name. This was present for most
but not all entries. Because the parsing doesn't reject unrecognized
entries, this didn't cause failures, but it wasn't strictly correct.
Submitted by: Martin Faxer <gmh003532@brfmasthugget.se>
MFC after: 2 weeks
some new IANA-blessed services and close some PRs. Ports for
Jabber and PostgreSQL.
PR: conf/35219, conf/35220
Submitted by: Sean Chittenden <sean@chittenden.org>
MFC after: 1 day
and looks like no other Unix diskless configuration I've ever seen.
Thus allow a more traditional /etc.
Note, the use of an MFS /var should also be settable.
Otherwise installing ports(packages) is just a total PITA.
rc.conf(5) and the files' inline documentation.
- Add the "closed"-type, documented in both places, but which did not
exist in the code.
- When provided a ruleset, the system should not make any assumptions
about the sites's policy and should add no rules of its own.
- Make the "UNKNOWN" (documented in-line) actual work as advertised,
load no rules.
Prodded by: Igor M Podlesny <poige@morning.ru>
MFC after: 1 week
when running natd(8) out of the rc-files. It is perfectly valid for
the interface or alias address to be set in a natd(8) configuration
file, not on the command line. Also, loosen up the restrictions on
identifying an IP address argument in 'natd_interface.'
Fix the documentation, rc.conf(5), to reflect this change.
Take the bogus default for 'natd_interface' out of /etc/defaults/rc.conf.
MFC after: 3 days
at boot (sendmail_enable=NO), a localhost-only daemon may started
(sendmail_submit_enable) as it is needed to accept mail from command line
submissions. If this isn't desired, see etc/mail/README for more hints.
Optionally (sendmail_msp_queue_enable) start a queue runner for the
submission queue in case a daemon isn't available to accept command line
submitted mail at submission time.
Note that the syslog labels for all of these sendmail processes have been
uniquified for easier log parsing.
works and ways to work around common problems people might have.
Include information on reverting to a set-user-ID root sendmail binary in
case anyone really needs to do this.
Checking for the existence of sendmail.cf is rather silly when someone
is using the mailwrapper(8) to run a mail daemon that is not actually
sendmail(8). It is also probably better to let sendmail(8) actually
try to start and error out if the administrator has
'sendmail_enable="YES"' but no sendmail.conf. At present, it would
fail silently.
Reviewed by: gshapiro
MFC after: 2 days
updated driver. The newer driver in current outputs a version string
that contains a space, so we need to eat two words in between RocketPortX
and the number of ports on the board.
values at all if they are not purposefully set. What if the
administrator messed with them in /etc/sysctl.conf? We don't want to
overwrite them.
If 'log_in_vain' is zero, do not force the issue. If it is non-zero,
set it.
pam_login_access(8) and pam_securetty(8) to enforce various checks
previously done by login(1) but now handled by PAM, and pam_lastlog(8) to
record login sessions in utmp / wtmp / lastlog.
Sponsored by: DARPA, NAI Labs
10 in -STABLE), pccardd's string comparison between
pccard.conf's entry and PC card's CIS tupple became strict
matching.
As influences of this commit, some PC cards don't work since
some /etc/default/pccard.conf's card identifiers entries are
incorrectly described.
- Lexar Media compact flash
- IO DATA CBIDE2 in 16 bit mode
- TOSHIBA Portable 24X Speed CD-ROM Drive PA2673UJ
- Hewlett Packard M820e (CD-writer)
Update these card configs.
PR: 33815
Obtained from: [bsd-nomads:16128]
/usr/share/examples/pppd.
Remove the out-of-place pppd(8) configuration files in etc/ppp,
ppp.shells.sample and ppp.deny.
Make the appropriate changes to the build process, etc/Makefile and
etc/mtree/BSD.usr.mtree, so it all works.
/usr/share/examples/pppd.
Update pppd(8) documentation to reflect this, usr.sbin/pppd/pppd.8.
Remove the out-of-place pppd(8) configuration files in etc/ppp,
ppp.shells.sample and ppp.deny.
Make the appropriate changes to the build process, etc/Makefile and
etc/mtree/BSD.usr.mtree, so it all works.
The files from etc/ppp, ppp.shells.sample and ppp.deny, were moved
with a repo copy. Note it in the logs with a forced commit to these
two.
Submitted by: Maxim Konovalov <maxim@macomnet.ru> provided the new samples.
This change was submitted to the freebsd-audit mailing list for review
but received no feedback. Hindsight-enabled reviews are welcome.
PR: conf/31358
Submitted: Thomas Quinot <thomas@cuivre.fr.eu.org>
# This card has the same PCMCIA and OEM id as ELSA XI300 wireless card, which
# appears to be listed elsewhere in this file.
Submitted by: Abe Toshiaki-san <ans@sun-tec.co.jp>
MFC After: 5 days
Try this out in -CURRENT, MFC, and then consider dropping the
'log_in_vain' knob all together. It really is something for
sysctl.conf(5).
PR: bin/32953
Reviewed by: -bugs discussion
MFC after: 1 week
The code will be fixed for all known security vulnerabilities,
and a make.conf(5) knob (ENABLE_SUID_MAN) will be provided for
those who still want it installed setuid for whatever reasons.
users who don't wish to use it. If the admin is worried about leaking
information about which users exist and which have OPIE enabled, the
no_fake_prompts option can simply be removed.
Also insert the appropriate pam_opieaccess lines after pam_opie to break
the chain in case the user is logging in from an untrusted host, or has a
.opiealways file. The entire opieaccess / opiealways concept is slightly
unpammish, but admins familiar with OPIE will expect it to work.
Reviewed by: ache, markm
Sponsored by: DARPA, NAI Labs
We now do it as a "camcontrol rescan all" which is something ken
promised to implement; for the time being it's not worse than the old
"camcontrol rescan $device" which ended up in something like
"camcontrol rescan aic1". Currently, camcontrol misinterprets the
third non-numeric arg as number 0, and rescans bus 0, which is about
the best we could get at this time.
Approved by: imp
MFC after: 1 week
The catpaging and setuidness features of man(1) combined make
it vulnerable to a number of security attacks. Specifically,
it was possible to overwrite system catpages with arbitrarily
contents by either setting up a symlink to a directory holding
system catpages, or by writing custom -mdoc or -man groff(1)
macro packages and setting up GROFF_TMAC_PATH in environment
to point to them. (See PR below for details).
This means man(1) can no longer create system catpages on a
regular user's behalf. (It is still able to if the user has
write permissions to the directory holding catpages, e.g.,
user's own manpages, or if the running user is ``root''.)
To create and install catpages during ``make world'', please
set MANBUILDCAT=YES in /etc/make.conf. To rebuild catpages
on a weekly basis, please set weekly_catman_enable="YES" in
/etc/periodic.conf.
PR: bin/32791
Submitted by: Michael Johansson <micke@nevermind.net>
o Sony PCWA-C100 WaveLAN card
Submitted by: "Jeremiah Gowdy" <jgowdy@home.com>
o Corega KK Wireless LAN PCCA-11 (version b?)
Submitted by: Masahide *MAC* Noda <mac@clave.gr.jp>
to have backward compatibility symbolic links.
This code should check existence of deprecated locales and
fix them using following scheme:
. if new locale directory exisists and is a symlink -- remove it
. if old locale directory exists and not a symlink -- rename it to
its new name
This should allow to mtree(1) and existing locale aliases make(1)
rules to setup locale dirs correctly (avoid self-referenced symlinks)
BTW, this commit brings in backward compatibility support for ru_SU
locales (aliased to appropriate ru_RU ones).
- The disktab was taken from etc.alpha.
- rc.sparc64 doesn't do anything right now.
- The ttys file has all the vty's commented out since we don't know how
those will work yet. Also, an entry is added for the Openfirmware
console device.
Submitted by: jake (partially)
a packed array so sizeof work. This broke RFMON mode and passing
up 802.11 packets.
The Linux emulation code was derived from the open source Linux driver to
maintain compatibility.
LEAP support is added, hints from Richard Johnson. I've verified this
locally with PC350v42510.img firmware. More bug fixing from Marco to
fix long passwords.
Change DELAYs in flash part of driver to FLASH_DELAY which uses tsleep
so it doesn't look like your system died during a flash update.
Install header files in /usr/include/dev/an
Cleanup some ifmedia bugs add "Home" key mode to ifmedia and ancontrol.
This way you can manage 2 keys a little easier. Map the home mode into
key 5. Enhance ifconfig to dump the various configured SSIDs. I use
a bunch of different ones and roam between them. Use the syntax similar
to the WEP keys to deal with setting difference SSIDs.
Bump up up the Card capabilities RID since they added 2 bytes to it
in the latest firmware. Thankfully we changed it from a terminal
failure so the card still worked but the driver whined.
Some cleanup patches from Marco Molteni.
Submitted by: Richard Johnson <raj@cisco.com>
Marco Molteni <molter@tin.it>
and myself
Various checks: David Wolfskill <david@catwhisker.org>
Reviewed by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Approved by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Obtained from: Linux emulation API's from Aironet driver.
types (networkfs_types) with a version that includes the original
list.
This increases the scope for user error and also means that systems with
networkfs_types set in /etc/rc.conf will not benefit from changes to the
list in /etc/defaults/rc.conf on upgrade.
Instead, store the default list in /etc/rc itself and allow the operator
to append to that list by specifying her own list in networkfs_types.
Rename networkfs_types to extra_netfs_types accordingly, as the new name
better describes the purpose of the variable. Default the value to
'NO'.
the network is initialized. This was first implemented in rev 1.268
of src/etc/rc, but was backed out at wollman's request.
The objection was that the right place for the fix is in mount(8).
Having looked at that problem, I find it hard to believe that
the hoops one would have to jump through can be justified by the
desire for purity alone.
Note that there are reported issues surrounding nfsclient kernel
support and mount_nfs(8), which currently make NFS an ugly exception
to the general case.
With this change, systems with non-NFS network filesystems configured
for mounting on startup in /etc/fstab are no longer guaranteed to
fail on startup.
o uncommnent joy stuff (me)
o Add BONDWELL B236 joystick card (me)
o Add Buffalo WLI-CF-S11G wi card (me)
o CNF CD-m (submitted by gda)
Submitted by: Dmitry A Goncharov <gda@sani.ru>
md device and file system creation occurs *after* mtree is run, and
as such an /var/tmp/* or /tmp/* entries will be under the mountpoint
(or fail) rather than appearing in the md filesystems. This prevents
the creation of vi.recover, and might affect other localizations that
rely on the mtree calls affecting these directories.
LC_MESSAGES related data was installed to <locale>/LC_MESSAGES file.
Now it go to <locale>/LC_MESSAGES/SYS_LC_MESSAGES file. LC_MESSAGES
directory is supposed to be storage of message catalogs of userland tools.
This should allow us to avoid many potential problems with future
libintl related functionality introduction.
Thanks for useful suggestions about correct way how to replace plain
files with directories at installworld stage to: Ruslan Ermilov <ru>
so swap the order.
Also allow rpc.lockd and rpc.statd to be turned on if nfsclient is
enabled. They are needed to provide client side locking support.
PR: conf/27811
already set (e.g. a failed/skipped mergemaster run during an upgrade).
Without this, if script_name_sep was not set in the rc.conf files,
local scripts will not be executed on startup or shutdown.
PR: misc/32687
Submitted by: Nicholas Paufler <echofox@discordia.ca> (the problem)
Sheldon Hearn (the idea behind the fix)
Reviewed by: sheldonh
MFC after: 1 week
- Add instructions regarding replacing 'my.domain', as this has come up
on freebsd-questions.
- Remove reference to rs.internic.net/templates, as that directory no
longer exists. Instead, encourage them gently to talk to their network
provider.
MFC after: 1 week
of /etc/daily. Some time later, /etc/daily became a set of periodic(8)
scripts. Now, this evolution continues, and /etc/security has been
broken into periodic(8) scripts to make local customization easier and
more maintainable.
Reviewed by: ru
Approved by: ru
kernel TCP timer code: rather than checking for tcp_keepalive being
set to "YES", check for "NO" and turn off keepalives if the variable
is set in that manner.
o Note: eventually, it would make sense to remove this variable from
rc.conf management, and instead rely on sysctl.conf. In fact, this
is probably true of a number of rc.conf variables whose sole aim
is to drive the setting of sysctls at boot time.
installed instead of pam.conf. This is for testing; the conditionals will
be removed once we are confident that pam.d works as intended.
Sponsored by: DARPA, NAI Labs
conversion script generated the wrong format, so the configuration files
didn't actually work. Good thing I hadn't thrown the switch yet...
Sponsored by: DARPA, NAI Labs (but the f***ups are all mine)
backward compatibility symlinks for good measure.
DEVFS already gets this right (except for the symlinks).
PR: 24781
Submitted by: Christian Weisgerber <naddy@mips.inka.de>
MFC after: 3 days
to get it all right, allowing ipnat to be enabled independantly of ipfilter
in rc.conf (among other things).
PR: multiple
Submitted by: Arjan de Vet <devet@devet.org>
Reviewed by: Giorgos Keramidas <keramida@FreeBSD.org>
Use these new functions instead of printf(1), which is scheduled for
removal as a shell builtin command, and which will not be available as a
standalone utility if MAKEDEV is run prior to mounting /usr.
Requested by: knu
smmsp - sendmail 8.12 operates as a set-group-ID binary (instead of
set-user-ID). This new user/group will be used for command line
submissions. UID/GID 25 is suggested in the sendmail documentation and has
been adopted by other operating systems such as OpenBSD and Solaris 9.
mailnull - The default value for DefaultUser is now set to the uid and gid
of the first existing user mailnull, sendmail, or daemon that has a
non-zero uid. If none of these exist, sendmail reverts back to the old
behavior of using uid 1 and gid 1. Currently FreeBSD uses daemon for
DefaultUser but I would prefer not to use an account used by other
programs, hence the addition of mailnull. UID/GID 26 has been chosen for
this user.
This was discussed on -arch on October 18-19, 2001.
MFC after: 1 week
the idea of not masking passwords on comments in case the
administrator comments out an entry without clearing the
password. Instead completely ignore comments (since they have no
security impact) when doing the diff of the old and new passwd file.
Suggested by: rwatson
extracted and recreating device files.
Without this, you'll see following messages when 'MAKEDEV all':
[: : out of range
[: : out of range
acd0t is invalid -- can't have more than 32 devices or 169 tracks
Reported by: David Syphers <dsyphers@uchicago.edu> (at current@FreeBSD.org)
continuation lines, extra whitespace, and to use the last matching
line in the file. This syncs the host.conf generation with how
the nsswitch.conf is parsed.
Only print " host.conf" instead of a multi-line message, since this
happens on every boot.
- if nsswitch.conf exists, host.conf is auto-generated for compatibility
with legacy applications and libraries.
- if host.conf exists but nsswitch.conf does not, nsswitch.conf is auto-
generated as usual.
`localhost'. If your /etc/nsswitch.conf has ``hosts: files dns'', and
you changed `myname.my.domain' in /etc/hosts to match hostname(1), and
you run inetd(8) with the -l option, any connect to `myname' using its
real IP address through inetd(8), e.g. `ftp -a myname', will spam your
/var/log/messages with:
inetd[PID]: warning: /etc/hosts.allow, line 23: host name/name mismatch: myname.my.domain != localhost
This is especially bad for -STABLE, where /etc/host.conf defaults to
"files first then DNS" resolution order.
Noticed by: Igor Kucherenko <kivvy@sunbay.com>
MFC after: 1 week
Many people like to use generic devices in rc.syscons, etc..
So rc.devfs needs to run before those rc files.
Requested by: Jos Backus <josb@cncdsl.com>
the original commit of local_startup depended on the scripts being
executable; so there is too much precedence to change it now. About all
anyone could agree on is that rev 1.274 broke POLA and before rev 1.274
also broke POLA.
dhclient and pccard_ether, introduce the concept of a "settle time" to
pccard_ether with the new pccard_ether_delay variable. Defaults to 5
seconds, which is enough time for the ed driver to finish its
autoconfiguration for newer Linksys based cards. This also can
eliminate the ed0: timeout messages that happen at startup as well.
MFC: after RE says OK.
appears to be another OEM version of the Netgear FA411. This is a
guess, since the original didn't include the flags, but this is too
similar to my netgear card...
Submitted by: neal@nelsonnet.org
permissions on some files, and give hints as to what those permissions
might be. Note also that the current more liberal permissions might
get changed in future revisions.
discussed on the arch@ mailinglist (after repo-copy).
sys.mk will .error if it finds /etc/defaults/make.conf but include
it anyways (this is the same behaviour as with the make.conf.local
removal).
/usr/share/examples/etc/make.conf has BDEFLAGS commented out now,
since it's only an example file.
Adjust all textes that talk about make.conf or defaults/make.conf to
match the new situation.
value, it forces GCC to not optimize above this level. For intance, GCC
made with "WANT_FORCE_OPTIMIZATION_DOWNGRADE=1" is a good setting for the
Alpha platform when building ports.
rc.firewall6. Specifically, don't do anything
if [ -z ${source_rc_confs_defined} ]. Not doing this leads to a problem
with dependencies: chkdepend will set, e.g., portmap_enable to YES if
some service that needs portmap is enabled, but rc.network sources
rc.firewall, which used to source defaults/rc.conf unconditionally,
which would result in portmap_enable being set back to NO.
PR: 29631
Submitted by: OGAWA Takaya <t-ogawa@triaez.kaisei.org>
and ftpd. This more conservative default reduces the exposure of
freshly installed machines, which is especially valuable for machines
that receive minimal further configuration before being put into
production. Generally speaking, SSH has superseded the use of both
telnet and ftp in many environments. In light of recent remotely
exploitable security holes in both telnetd and ftpd, this choice
retains flexibility (both telnetd and ftpd daemons remain installed
and easily enableable) while protecting users who don't need the
additional risk. This change brings our configuration into line with
the majority of other UNIX vendors, including OpenBSD and NetBSD.
To address the concerns of those requiring remote access via telnet
from first install, changes will shortly be committed to sysinstall
to provide the ability to edit inetd.conf during the installation
process, allowing telnetd and ftp to be re-enabled during the
installation process.
While I'm at it, slightly improve commenting for inetd.conf so that
it's more clear to users how to enable and disable services.
Further commenting to indicate the functions of various columns would
probably also be useful.
Reviewed by: imp, chris, jake, nate, -arch, -stable
is required into rc.network.
Person failed to use a real name so both email addresses from PR included
(Sent was different to From).
PR: 22998
Submitted by: dl@leo.org/spock@empire.trek.org
us anyway because it doesn't work right on the x86 and alpha. On
K&R code, small ints would be promoted to int. ANSI-C doesn't require
this and the small ints can be passed taking 8 or 16 bits of stack
space. However, the x86 abi that we use *does* promote to 32 bit,
and the alpha ABI passes them in 64 bit registers so we dont have
that aspect of the problem here. Losing float precision by having it
cast down to int because the funtion prototype specifies int is the
least of our problems. -Wmissing-prototypes helps here anyway.
correct some ommissions of udp ports.
Update IANA web page.
Clean up/correct some comments. I went a little further than the PR.
PR: conf/23416
Submitted by: Rudolf Cejka <cejkar@dcse.fee.vutbr.cz>
install /etc/mail/sendmail.cf to /etc/mail/sendmail.cf and exits with an
error:
===> etc/sendmail
install -c -o root -g wheel -m 644 /etc/mail/sendmail.cf /etc/mail/sendmail.cf
install: /etc/mail/sendmail.cf and /etc/mail/sendmail.cf are the same file
*** Error code 64
Catch this in the Makefile and don't call install if the source and target
are the same file.
Reported by: Alexandr Listopad <laa@reis.zp.ua>
MFC after: 1 week
building a .cf file from a .mc file.
Include -D_FFR_TLS_O_T to enable tls policy control since the sendmail binary
build enables that FFR as well.
PR: conf/28361
MFC after: 1 week
for separating the startup scripts' list into individual filenames.
Run the shutdown scripts in reverse alphabetical order, so dependent
services are stopped before the services they depend upon.
Reviewed by: -arch, -audit
MFC after: 3 weeks
non-printable characters to sneak into /var/log/messages (e.g.
someone aims a Solaris/Linux RCP exploit at your FreeBSD box and
you end up with his shellcode as part of a log entry). You might
get something like,
host.mydom.org login failures:
Binary file (standard input) matches
In the daily security script as a result. Allowing attackers to
mess with your security script's ability to accurately report
is a Bad Thing. Tell grep(1) to treat /var/log/messages like a
text file even if it has non-printable characters.
Submitted by: Tim Zingelman <zingelman@fnal.gov> on freebsd-security
Approved by: ru
MFC after: 1 week
the default section and into the papchap section.
It's really irritating when you run ppp with no arguments and end up
blowing away your default route !
the following description in RFC2461:
AdvSendAdvertisements
A flag indicating whether or not the router sends
periodic Router Advertisements and responds to
Router Solicitations.
Default: FALSE
Note that AdvSendAdvertisements MUST be FALSE by
default so that a node will not accidentally start
acting as a router unless it is explicitly
configured by system management to send Router
Advertisements.
Submitted by: JINMEI Tatuya <jinmei@isl.rdc.toshiba.co.jp>
MFC after: 1 week
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.
TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.
Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks
after the network is configured.
Future remote filesystem types should be added to remote_fstypes, which
is a whitespace-delimited list of type:description pairs.
The specific problem this fixes right now is that smbfs mounts described
in /etc/ftsab were failing.
Make the default setting YES for now to get some experience with it.
Note: If people starts seeing disk errors because of this then it
should not be backed.
With a small disk being 20GB these days, chances are pretty good that
an ailing sector will not be read while still being recoverable by
the drive.
Diskcheck daemon will read disks in the background at a low rate and
that way give the diskdrive a chance to detect and correct soft read
errors before they become hard errors.
Idea by: phk
Written by: ben
about non-existent mount directories (which would come
into existence after the real mount has occured) when just
testing for if there are any NFS filesystems in /etc/fstab.
PR: bin/26597
Submitted by: Dmitry Morozovsky <marck@rinet.ru>
MFC after: 3 days
systems were repo-copied from sys/miscfs to sys/fs.
- Renamed the following file systems and their modules:
fdesc -> fdescfs, portal -> portalfs, union -> unionfs.
- Renamed corresponding kernel options:
FDESC -> FDESCFS, PORTAL -> PORTALFS, UNION -> UNIONFS.
- Install header files for the above file systems.
- Removed bogus -I${.CURDIR}/../../sys CFLAGS from userland
Makefiles.
is not set. This allows admins to create a per-machine configuration file
while leaving the freebsd.mc template pristine. Provide a rule to create
`hostname`.mc from freebsd.mc if it doesn't exist.
PR: misc/26299
MFC after: 8 days
fsck checking. Applying these changes (typically via mergemaster)
will cause your system to start running background checks on all
your soft update enabled filesystems (provided that you have
a kernel with the required functionality, e.g., one built since
the end of April). Please report any and all problems to
mckusick@mckusick.com (not mckusick@freebsd.org which I read
infrequently). See the comment above the fsck command in /etc/rc
for instructions on how to disable background checking should it
cause you too much trouble.
Several FAQs:
1) Can I reboot before the background checks are done?
Ans) Yes, when the system restarts the checks will pick up
where they left off.
2) Can a crash during checking corrupt my filesystem?
Ans) No, recovered resources are returned to the system using soft
updates which ensure that the freeing is done in a safe order.
3) How will I know if any background checks are being done?
Ans) Filesystems that are to be checked in background will be listed
as `DEFER FOR BACKGROUND CHECKING' at the usual fsck check time
during system startup.
4) What happens to the output of the background checks?
Ans) It is sent to syslog `daemon' facility log level `notice'.
5) When will this feature be available in the 4.X kernel?
Ans) Never. It is much too radical and extensive a change to be
MFC'ed. Besides, it needs many months of experience and
tuning before it is ready for widespread use.
6) What happens if a background fsck fails (i.e., fsck finds
errors that would normally require a manual fsck)?
Ans) The filesystem will be marked as needing a manual fsck.
At the next system reboot, the check will be done in
foreground and the usual actions taken (usually a failure
to go multi-user until fsck has been run by hand on the
affected filesystem).
the null mount, we currently create a temporary mfs on /tmp, copy
/etc to /tmp, then mount /etc as mfs and copy everything back from
/tmp, then delete the /tmp mfs.
The patch eliminates the temporary /tmp mfs and the subsequent
copying and simply populates the /etc mfs by copying from
/conf/default/etc. This requires that /conf/default/etc contain a
complete copy of all the /etc stuff instead of just overrides. I
don't think that is too much of an extra step in setting up a
diskless environment.
* Provide the ability to make /tmp a memory filesystem independent
of /var. This removes the requirement that /tmp be a symlink to
/var/tmp and this makes the diskless code work with the default
filesystem layout. If a seperate /tmp memory filesystem is
created, the 'tmpsize' environment variable is used to determine
its size (default to 10 Meg).
* Reduce diffs between the -current and -stable versions of these
files to a bare minimum. Only the definition of the shell
function 'mount_md' is different.
Not Objected to by: -arch@, -small@
MFC after: 2 days
This driver supports PCI Xr-based and ISA Xem Digiboard cards.
dgm will go away soon if there are no problems reported. For now,
configuring dgm into your kernel warns that you should be using
digi. This driver is probably close to supporting Xi, Xe and Xeve
cards, but I wouldn't expect them to work properly (hardware
donations welcome).
The digi_* pseudo-drivers are not drivers themselves but contain
the BIOS and FEP/OS binaries for various digiboard cards and are
auto-loaded and auto-unloaded by the digi driver at initialisation
time. They *may* be configured into the kernel, but waste a lot
of space if they are. They're intended to be left as modules.
The digictl program is (mainly) used to re-initialise cards that
have external port modules attached such as the PC/Xem.
o create a simple wrapper function mount_md that makes it easy to
move from mount_mfs.
# NOTE: you will need to MAKEDEV md[0123] in order for this to work.
Reviewed by: bsd, keichii
/dev/log like this: if [ ! -h /dev/log ];
The man page for test(1) says that the -h switch is depracated and that
users should NOT rely on it being available. It suggest the -L switch instead.
They both do the same thing: check for the existence of the symbolic link.
PR: 26596
Submitted by: mikem <mike_makonnen@yahoo.com>
BSDPAN is the collection of modules that provides tighter than ever
integration of Perl into BSD Unix.
Currently, BSDPAN does the following:
o makes p5- FreeBSD ports PREFIX-clean;
o registers Perl modules in the FreeBSD package database with a
package name derived from the module name.
The name is of the form: bsdpan-ModuleName-V.VV.
Anyone interested in where BSDPAN is developing should read Anton's
message to the ports mailling list:
Message-ID: <20010105040828.A26011@heechee.tobez.org>
Submitted by: Anton Berezin <tobez@tobez.org>
default first, then network-specific files, then host-specific files.
I think this was the original intent, as Matt indicated the previous
code appeared to be a bug.
out of sync. A similar change was made by itojun on the OpenBSD tree
a few weeks ago. This should stop people disabling one server and
forgetting the other one (eg: ftp and/or telnet)
NO_MAKEDEV_INSTALL and NO_MAKEDEV_RUN. The former implying the latter.
The names imply what they do. The last commit by DES based on a PR defeated
the original idea behind NO_MAKEDEV, which was not to run MAKEDEV, but to do
the installation of MAKEDEV. This should satisfy both parties on the MAKEDEV
challenge.
Note that "right" in this case is not universally recognized, but
NTP-practittioners as opposed to theoretians generally agree that
getting "inside the window" using ntpdate is TRTTD on PC hardware.
PR: 25514
Submitted by: Chris Johnson <cjohnson-pr@palomine.net>
The PAM_FAIL_CHECK and PAM_END macros in su.c came from the util-linux
package's PAM patches to the BSD login.c
Submitted by: "David J. MacKenzie" <djm@web.us.uu.net>
very specific scenarios, and now that we have had net.inet.tcp.blackhole for
quite some time there is really no reason to use it any more.
(second of three commits)
associated changes that had to happen to make this possible as well as
bugs fixed along the way.
Bring in required TLI library routines to support this.
Since we don't support TLI we've essentially copied what NetBSD
has done, adding a thin layer to emulate direct the TLI calls
into BSD socket calls.
This is mostly from Sun's tirpc release that was made in 1994,
however some fixes were backported from the 1999 release (supposedly
only made available after this porting effort was underway).
The submitter has agreed to continue on and bring us up to the
1999 release.
Several key features are introduced with this update:
Client calls are thread safe. (1999 code has server side thread
safe)
Updated, a more modern interface.
Many userland updates were done to bring the code up to par with
the recent RPC API.
There is an update to the pthreads library, a function
pthread_main_np() was added to emulate a function of Sun's threads
library.
While we're at it, bring in NetBSD's lockd, it's been far too
long of a wait.
New rpcbind(8) replaces portmap(8) (supporting communication over
an authenticated Unix-domain socket, and by default only allowing
set and unset requests over that channel). It's much more secure
than the old portmapper.
Umount(8), mountd(8), mount_nfs(8), nfsd(8) have also been upgraded
to support TI-RPC and to support IPV6.
Umount(8) is also fixed to unmount pathnames longer than 80 chars,
which are currently truncated by the Kernel statfs structure.
Submitted by: Martin Blapp <mb@imp.ch>
Manpage review: ru
Secure RPC implemented by: wpaul
Xircom CreditCard Netwave cnw
Intel PRO/Wireless 2011 (PRISM II) wi
3COM 3CRWE737A (PRISM II) wi
Note: I've had some reports that the latter two cards work, but I've not
been able to get them to work for me.
enable all harvesting options by default since having them on for
devices not present doesn't hurt anything. Leave them on by default
since for the most part they are not producing noticable slowdown,
and are about to get a lot more efficient.
Re-order part of the cheesy entropy process in preparation for
its complete removal.
during the boot process. We're turning it on by default, based on the
actual presence of a configured ethernet card, and/or ppp/tun devices.
Of course, it's easy to disable in rc.conf.
1) blackholes.mail-abuse.org is the same as FEATURE(dnsbl), so specifying
it in the "Other DNS based black hole lists" section leads to confusion of
specifying it twice.
2) Formatting issues. If error diagnostic not enclosed in double quotes,
varius visual artefacts appearse like 1) no space after ; and 2) redundant
space after ? (in CGI request), so I add quotes where needed.
3) FEATURE(dnsbl) directly use error code 550 by default, so I made other
dnsbl variants use the same error code too.
4) Comment relays.* list as "open relays" list, just "other" word is not
explain enough.
Submitted by: ache
and Pentium II, III and IV processors (p2, p3, p4), as well as 'mmx' and
'3dnow' MACHINE_CPU tags as appropriate. In the near future this will
be used to control various ports which have MMX/3dNow optimizations,
instead of the ad-hoc methods currently used.
Reviewed by: peter
libssl, for example), and hide it behind a make.conf option,
WANT_OPENSSL_MANPAGES, instead of having it commented out. We still can't
install these by default because of clobbering of a number of system
manpages with the same name, but they're there for people who want them.
* Rip out MACHINE_CPU stuff from sys.mk and include a new <bsd.cpu.mk>
after we pull in /etc/make.conf. We need to do it afterwards so we can
react to the user setting of the:
* CPUTYPE variable, which contains the CPU type which the user wants to
optimize for. For example, if you want your binaries to only run on an
i686-class machine (or higher), set this to i686. If you want to support
running binaries on a variety of CPU generations, set this to the lowest
common denominator. Supported values are listed in make.conf.
* bsd.cpu.mk does the expansion of CPUTYPE into MACHINE_CPU using the
(hopefully) correct unordered list of CPU types which should be used on
that CPU. For example, an AMD k6 CPU wants any of the following:
k6 k5 i586 i486 i386
This is still an unordered list so the client makefile logic is simple -
client makefiles need to test for the various elements of the set in
decreasing order of priority using ${MACHINE_CPU:M<foo>}, as before.
The various MACHINE_CPU lists are believed to be correct, but should be
checked.
* If NO_CPU_CFLAGS is not defined, add relevant gcc compiler optimization
settings by default (e.g. -karch=k6 for CPUTYPE=k6, etc). Release
builders and developers of third-party software need to make sure not to
enable CPU-specific optimization when generating code intended to be
portable. We probably need to move to an /etc/world.conf to allow the
optimization stuff to be applied separately to world/kernel and external
compilations, but it's not any worse a problem than it was before.
* Add coverage for the ia64/itanium MACHINE_ARCH/CPUTYPE.
* Add CPUTYPE support for all of the CPU types supported by FreeBSD and gcc
(only i386, alpha and ia64 first, since those are the minimally-working
ports. Other architecture porters, please feel free to add the relevant
gunk for your platform).
Reviewed by: jhb, obrien
+ Add support for the new SENDMAIL_MC make.conf knob
+ Add the ability to build .cf files from .mc files
+ Generalize map rebuilding
+ Add the ability to rebuild the aliases file
+ Add the ability to stop, start, and restart sendmail
PR: bin/13759, bin/19897, bin/24397
users should be configuring via m4 now. If set, use m4 to create the .cf
file. Also, if either SENDMAIL_MC or SENDMAIL_CF is set, 'make install' or
'make distribution' in src/etc/sendmail/ will install the appropriate .cf as
/etc/mail/sendmail.cf. This fixes some mergemaster problems.
PR: conf/13016
Makefile to the etc/sendmail Makefile to be consistent with all of the
other /var file creations. In doing so, change the Makefile target from
etc-sendmail.cf to distribution as it installs more than just the sendmail.cf.
pass udp from any 53 to ${oip}
allows an attacker to access ANY local port by simply binding his local
side to 53. The state keeping mechanism is the correct way to allow DNS
replies to go back to their source.
through the use of a new build directive, MACHINE_CPU, which contains a
list of the CPU generations/features for which optimizations are desired.
This feature will be extended to cover the ports tree in the future.
Currently OpenSSL provides optimizations for i386, i586 and i686-class
CPUs. Currently it has not been tested on an i386 or i486.
Teach make(1) to provide sensible defaults for MACHINE_CPU if it is not
defined (namely, the lowest common denominator CPU we support for each
architecture). Currently this is i386 for the i386 architecture and ev4
for the alpha. sys.mk also sets the variable as a last resort for
consistency with MACHINE_ARCH and bootstrapping from very old versions of
make.
Benchmarks show a significant speed increase even in the i386 case, with
additional improvements for i586 and i686 systems. For maximum performance
define MACHINE_CPU=i686 i586 i386 in /etc/make.conf.
Based on a patch submitted by: Mike Silbersack <silby@silby.com>
Reviewed by: current
trigger happy and turn off sendmail_enable entirely (instead of setting
sendmail_flags to -q30m instead). I have seen boxes with things like daily
run reports that have sat in mailq for 5 months. Since /usr/sbin/sendmail
is actually mailwrapper, this should be safe for the other plugins that
provide the sendmail calling interface.
default syslog target for console messages (when enabled in
syslog.conf). Use the same rotation defaults as with
/var/log/messages -- every 100kb of log, compress back logs,
and keep five rotated logs.
o Note: phk also thought it would be useful to force rotation
each boot. This commit does not introduce such a rotation.
Reviewed by: phk
compiled in. This involves a commented out sshd line to match the
remainder of the commented out pam_kerberosIV.so entries. This
doesn't quite restore the correct behavior, as ticket files are
not managed properly, but it's an improvement.
Forgotten by: green
just messages{,.0*} when looking for login failures and refused
connections.
PR: 23415
Mostly submitted by: phk
Convert a few " "s to tabs while I'm here - for consistency.
reference. The sysinstall binary is now in root's standard PATH,
so there's no need for explicit pathing, and there's some value
in a manual page reference.
- ipv6_network_interfaces has all available interfaces to work for
static configuration even if the host is end host. When rtsol is
invoked, singleness of interface is checked.
it at boot time closer to the way we want it to be in the final version.
* Move the default directory to /var/db/entropy
* Run the entropy saving cron job every 11 minutes. This seems
to be a better default, although still bikeshed material.
* Feed /dev/random some cheesy "entropy" from various commands
and files before the disks are mounted. This gives /dev/random
a better chance of running without blocking early.
* Move the reseeding with previously stored entropy to the point
immediately after the disks are mounted.
* Make the harvesting script a little safer in regards to the
possibility of accidentally overwriting something other
than a regular file.
it can be used to reseed at boot time. This will greatly increase
the chances that there will be sufficient entropy available at
boot time to prevent long delays.
For /etc/rc, remove the vmstat and iostat runs from the attempt
to provide some cheesy randomness if the files fail, since
those programs are dynamically linked, and ldd seems to want
some randomness to do its magic.
Guidance and parameters for this project were provided by
Mark Murray, based on the requirements of the Yarrow
algorithm. Some helpful suggestions for implementation
(including the tip about iostat and vmstat) were provided
by Sheldon Hearn. All blame for problems or mistakes is
mine of course.
as the previous line already tells us we are in rc.${MACHINE_ARCH}. This
also allows more syscons configuration messages during startup to fit on
one line.
Reviewed by: dougb
one-way hash functions for authentication purposes. There is no more
"set the libcrypt->libXXXcrypt" nightmare.
- Undo the libmd.so hack, use -D to hide the md5c.c internals.
- Remove the symlink hacks in release/Makefile
- the algorthm is set by set_crypt_format() as before. If this is
not called, it tries to heuristically figure out the hash format, and
if all else fails, it uses the optional auth.conf entry to chose the
overall default hash.
- Since source has non-hidden crypto in it there may be some issues with
having the source it in some countries, so preserve the "secure/*"
division. You can still build a des-free libcrypt library if you want
to badly enough. This should not be a problem in the US or exporting
from the US as freebsd.org had notified BXA some time ago. That makes
this stuff re-exportable by anyone.
- For consistancy, the default in absence of any other clues is md5. This
is to try and minimize POLA across buildworld where folk may suddenly
be activating des-crypt()-hash support. Since the des hash may not
always be present, it seemed sensible to make the stronger md5 algorithm
the default.
All things being equal, no functionality is lost.
Reviewed-by: jkh
(flame-proof suit on)
o Add the removable_interfaces variable for list of removable network
interfaces (PC-card ethernet, wireless network and USB ethernet etc).
o ifconfig_<ifn>_alias0, static_routes_<ifn>, removable_route_flush,
/etc/start_if.<ifn> and /etc/stop_if.<ifn> are support.
o removable_route_flush variable is set to "NO" if you want to use the
machine as gateway using two or more removable network cards. If
static routing is needed use static_routes_<ifn> instead of
static_routes or defaultrouter.
o The optional static_routes_<ifn> variable is likely static_routes.
o /etc/start_if.<ifn> and /etc/stop_if.<ifn> are shell script to be
specified that are called when a card is inserted or removed.
multifunction cards and I recieved reports that the card does not
workd by `config auto'. (MFPAO)
o Remove static assign of the IRQ number.
o Remove two duplicated entries.
o Join some entries using regex and fixed matching order problem.
These changes for boot.flp.
Suggested by: sanpei
distinction between the OS copyright message and the message displayed
gratuitously to each user at login. Because, well, they may be
different, among other things, and boy can a copyright message each
login consume some screen space. If people really want to do this,
they can copy /COPYRIGHT to /etc/COPYRIGHT.
Submitted by: Anders Andersson <anders@codefactory.se>
require the addition of flag 0x80000 to their config line in
pccard.conf(5). This flag is not optional. These Linksys cards will
not be recognized without it.
Reviewed by: imp, iwasaki
Apply a more consistent style to the echo statements in /etc/ scripts.
* Put quotes around each line
* Single quotes for lines with no variable interpolation
* Double quotes if there is
* Capitalize each word that begins a line
* Make echo -n 'Doing foo:' ... echo '.' more of a standard
Also:
* Use rm -f on /var/run/dev.db so if it's not there (devfs) it doesn't error
* Shorten the ldconfig messages so that the default fits on one line
* Test whether /var/msgs/bounds is a link before overwriting it
* Generally futz around with whitespace
* Put quotes around each line
* Single quotes for lines with no variable interpolation
* Double quotes if there is
* Capitalize each word that begins a line
* Make echo -n 'Doing foo:' ... echo '.' more of a standard
No functionality changes
In a few days I will commit a patch which changes vn(4) to use the
disk-minilayer. This will make vn(4) fully DEVFS friendly but have
the side effect that vnconfig needs the vn%d.ctl devices to be able
to configure vn(4).
Please remake your /dev/vn entries with this revision of MAKEDEV if
you don't rung DEVFS already.
from "PCMCIA SCSI MBH1040" to "PCMCIA SCSI MBH10401" "01". They are
based on the spc driver.
This will fix the conflicts of entry with REX-5536AM, REX-9836A,
and ICM PSC-2401 ("MBH10404" ones) which are based on stg driver.
The problem was pointed out in bsd-nomads several times since PAO2 days.
-Comment out the entry for "MBH10401" ones. The spc driver is
not supported yet.
-Add more comment about cards which has broken CIS
(some cards which has tuple of "PCMCIA SCSI MBH10404" "01").
Reported by: takachan@running-dog.net, y-nakaga@nwsl.mesh.ad.jp,
yuki@dayo.ne.jp
Obtained from: discussion in bsd-nomads mailing list
for a hung `daily' run to keep a `weekly' run from happening.
Same for `monthly'. We have always run `weekly' and `monthly' reguardless
of the execution status of `daily'. Until there is some consensus we should
not change the behavior.
On Saturdays, run daily and weekly sequentially, starting at 03:01 am.
This prevents daily and weekly from overlapping, while running weekly as
early as possible (i.e. as soon as daily finishes) to give it time to
finish before monthly starts at 05:30 am.
It's probably possible to do something similar with monthly, making it
run as soon as daily (and possibly weekly, if the first of the month
is a Saturday) finishes, but this is left as an exercise for the reader.
work right when the administrator has modified their runtime environment
in a manner not anticipated by our script.
Requested by: Tom Maher <tardis@ece.cmu.edu>
for a while, but a recent email to -stable suggests it should be spelled
out as the documentation of "password_format" is sparse.
Also add a `des_users' entry.
Submitted by: Sean O'Connell <sean@stat.Duke.EDU>
over the past couple years. The most recent came to the general consensus
that this was the best time, but no one actually made the change, so I'll
don my asbestos undies and dive in.
Please note that this time was chosen with input from people in various
countries with various methods and schedules for switching to and from DST.
There is no perfect time to schedule this job that works for everyone, but
this time both A) Works for more people, and B) Causes problems for fewer
people. And, ultimately, you can always change it if you need to.
ENABLE_SUID_SSH being defined reenable it for those that want it.
This follows discussion favoring the change from September. It
is not usually necessary to be setuid root, possibly less safe,
and less convenient (cannot use $HOSTALIASES, for example).
Submitted by: jedgar
overwriting $PATH, and find mknod $PATH instead of hardcoding /sbin so
that the copy of MAKEDEV on the fixit floppy is usable, since mknod and
expr live in /mnt2/stand when the fixit floppy is running.
Get rid of the sed invokation in release/Makefile that attempts to
delete the PATH setting stuff from MAKEDEV on the fixit floppy. This
hasn't worked since a long ago change to MAKEDEV caused the sed
expression to no longer match.
PR: misc/21241
a) the configured default printer entry might turn out to become a security hole
Although lpd isn't enabled by default in FreeBSD 4 and later versions
bad things might happen because of a simple copy and paste failure:
- fill up root-fs, if /dev/lpt0 doesn't exist
- fill up the spool dir (either root-fs or var-fs) if machine hadn't been
designed as print server
Therefore best decision: if people want printing, then configure both
1. /etc/rc.conf
2. /etc/printcap
the default entry wouldn't have served well all tastes and needs anyway...
design of most of our config files is, to have commented out suggestions
if a service is not active.
b) [Garance]
fix old and wrong documentation:
input filters are possible even if you print to a remote printer
this makes FreeBSDs implementation of lpd currently the best without
having to switch to port monster LPRng ...
c) fix pointer to wrong handbook section for a longer time .. so I doesn't fix the number
I'm only referring to the printing section, otherwise this would have to be fixed several
times, if the chapters should be reordered again ...
d) typo: chose -> choose
Submitted by: me and some suggestions by Garance
Approved by: Eivind and Garance A Drosihn <drosih@rpi.edu> in private e-mail
cosmetic changes
use /etc/pccard_ether for Xircom CreditCard Netwave
and 3Com Corporation" "3C562" (BUT NOT SUPPORTED).
fix `card line' of RATOC REX-5572 (as SCSI only)
use `config auto' for RATOC REX-5536AM, REX-9836A,
ICM PSC-2401 SCSI
- rtsol should be work for only one interface
- new variable ipv6_defaultrouter is added
- option name of rtadvd in comment are corrected
- ipv6_firewall_enable, ipv6_firewall_type, ipv6_firewall_script,
ipv6_firewall_logging are added to introduce rc.firewall6.
IPv6 firewall rule is just starting point and should be brushed up.
This commit includes PR18621, PR21694, PR22051.
PR: conf/18621, conf/21694, conf/22051
Reviewed by: asmodai
used in lower layer (scsi_low.c).
The flag of ncv for KME KXLC004 was chaged from 0x1 to 0x100.
The flag of nsp for PIO mode was chaged from 0x1 to 0x100.
I wasn't dropping the interface correctly, but not noticing because
the interface was going away when the card was ejected.
Submitted by: Motomichi Matsuzaki <mzaki@e-mail.ne.jp>
This confilcted with the entry of non PIO mode.
If you want to use them in PIO mode comment out entry of the non PIO mode
and uncommnet the PIO mode entry.
and stg drivers. Also all config indexes for these cards are changed
to auto.
Note, still if you would like to use cards which has a comment;
# (Do not put this entry under Bustoaster)
you need some quick hack. Uncomment the entry above.
Reviewed by: sanpei@FreeBSD.org
bind distribution, but until now was not being built as a separate
entity. For documentation, see these man pages:
assertions(3), eventlib(3), heap(3), logging(3), memcluster(3), tree(3).
Reviewed by: jdp
brought them to BSDcon and gratiously allowed me to test each one with
the wireless setup here. In addition, support another CF card which
YAMAMOTO-san also brought.
Also add a Lexar CF card which didn't work with auto on many laptops.
the 'ifconfig ifN delete' into pccard_ether under the 'stop'
function.
In addition start dhclient with a pid file based on the interface
name, e.g. /var/run/dhclient.ep0.pid, and kill the correct dhclient
(or dhcpc) process when the card is removed.
convinced myself that it's better then what we have, but still
not perfect.
/etc/rc : Attempt to seed /dev/random with multiple backoffs.
/etc/rc.shutdown : Attempt to write the entropy_file.
In debugging the above changes, I've run into some
inconsistancies... rc.shutdown is run via 'init 6', but
does not appear to be run via '/sbin/reboot'. Thus, this
set of changes improves life depending on the mechanism
used to shut the system down.
Submitted by: Doug Barton <DougB@gorean.org>
Approved by: markm
not allocate a pty(4) so it is not suitable at all for interactive
PAM modules. rlogind calls login(1) which is already PAM enabled.
Approved by: markm
the appropriate documentation added to rc.conf(5). If all goes well
with this over the next few weeks, the PR will be closed with the
pullup of patches back to 4-STABLE.
PR: 20202
Submitted by: Gerhard Sittig <Gerhard.Sittig@gmx.net>
Reviewed by: Darren Reed <darrenr@freebsd.org>
Approved by: Darren Reed <darrenr@freebsd.org>
Obtained from: Gerhard Sittig <Gerhard.Sittig@gmx.net>
are bad enough, but finger is hardly a critical system service and
it's traditionally been vulnerable to a variety of attacks; anybody
remember RTFM and his worm?
PC-card stuff. Also print a NEWLINE (!!) after that.
I'm driving mad each time when I see messages related to pccard before
"Enable PC-card." and particulary when I see
"Doing initial network setup". on the same line w/o a break.
make_dev() call.
At the moment, it is an error for anyone but root to write to this
device (EPERM), and the permissions don't suggest that. Soon, however,
anyone will be able to write here, but only root will cause an implicit
reseed.
All periodic sub-scripts <larf> now have their return codes interpreted
by periodic(8). Output may be masked based on variable values in
periodic.conf.
It's also now possible to email periodic output to arbitrary addresses,
or to send it to a log file, examples of which can be found in
newsyslog.conf.
The upshot of it all should be no discernable changes to the default
behaviour of periodic(8).
PR: 21250
-- Unknown
Now that the RSA algorithm is released into the public domain, build
librsaintl by default unless NO_RSAINTL is set in make.conf.
The native OpenSSL implementation of RSA is much faster, doesn't have
an artificial keysize limitation, has 30% fewer calories and tastes great!
configure FreeBSD so that various databases such as passwd and group can be
looked up using flat files, NIS, or Hesiod.
= Hesiod has been added to libc (see hesiod(3)).
= A library routine for parsing nsswitch.conf and invoking callback
functions as specified has been added to libc (see nsdispatch(3)).
= The following C library functions have been modified to use nsdispatch:
. getgrent, getgrnam, getgrgid
. getpwent, getpwnam, getpwuid
. getusershell
. getaddrinfo
. gethostbyname, gethostbyname2, gethostbyaddr
. getnetbyname, getnetbyaddr
. getipnodebyname, getipnodebyaddr, getnodebyname, getnodebyaddr
= host.conf has been removed from src/etc. rc.network has been modified
to warn that host.conf is no longer used at boot time. In addition, if
there is a host.conf but no nsswitch.conf, the latter is created at boot
time from the former.
Obtained from: NetBSD
cached when not in use. This changes the FreeBSD default from 30 minutes
to 5 minutes. JKH was the one that added the override to amd_flags, but
there was no reason given other to serve as an example of what could be
done.
not when ${firewall_type} is set to a filename, as we know
nothing about user's script specifics.
Reported by: Bernhard Valenti <bernhard.valenti@gmx.net>
X field is treated the same as the unit number for acdX. The optional
Y parameter specifies the number of track devices to create starting at
track 1. If Y is not specified, it defaults to 100.
- Add the acd0t target to the all target to preserve previous behavior.
- Don't add the acd0t target to the fixit target, thus keeping the fixit
floppy from running out of i-nodes.
which really wasn't such a hot idea in retrospect.
If the random device isn't available, it probably isn't wanted.
If it's wanted, it should be enabled in loader.conf.
the output for the linux_enable and svr4_enable stuff "floating
in the middle of nowhere".
Give them their own section, called "additional ABI support".
kernel modules for ibcs2_enable and svr4_enable.
Don't rely on a shell script to do the neglibly less simple
job of loading a kernel module and running one command for
linux_enable.
These shell scripts are going away.
IPX folks a fighting chance of figuring this out themselves. I can't
work out how to document this carefully in rc.conf(5), but this ought
to close the PR.
PR: 17904
Reported by: John Gelnaw <jeg@hawk.circa.ufl.edu>
SUPFLAGS when a 'make update' is run. This means that the supfile
doesn't need to be edited because the -h will override the
CHANGE_THIS.FreeBSD.org host.
Beyond changes to the build system, this includes fixing up the sample
freebsd.mc configuration for changes in defaults and syntax, removing
outdated documentation, and updating the release notes.
it lives in /usr/bin. Instead, locate files manually.
Note, only *files* under /var/spool/lock are now deleted rather
than everything that's not a directory. I think this is more
correct, but if anyone disagrees please feel free to change it.
Problem pointed out by: bde
Make sysinstall override this on install, so the effective behavioural
change for a newly installed system is null. Overall, this makes a system
with an empty /etc/rc.conf not run any network services, and makes the
FreeBSD-provided network services that are running visible in /etc/rc.conf
(instead of making people look through /etc/defaults/rc.conf to find the
things they need to disable to secure the system.)
Reviewed by: jhb
Discussed with: The usual cabal
Add hints towards login.conf(5), which should be the preferred way
to set this systemwide without having to worry about the shell used.
PR: 9245
Submitted by: martin Kammerhofer <dada@sbox.tu-graz.ac.at>
build process in too many cases. Adding mtree to bootstrap-tools
to solve this breaks the upgrade path because mtree needs a
libc that has strtofflags and fflagstostr.
The tap driver is used to present a virtual Ethernet interface to the
system. Packets presented by the network stack to the interface are
made available to a character device in /dev. With tap and the bridge
code, you can make remote bridge configurations where both sides of
the bridge are separated by userland daemons.
This driver also has a special naming hack to allow it to serve a similar
purpose to the vmware port.
Submitted by: myevmenkin@att.com, vsilyaev@mindspring.com
time, and this is used to reseed the random number generator at
boot time.
NOTE - this has no hope of working if you halt(); you need to
execute rc.shutdown to get the entropy stash.
- Remove unit numbers in config lines.
- Remove all of logger lines and add logstr lines for some cards. This
changes reduced file size from 84k to 45k.
- Use '/sbin/ifconfig $device delete' instead of /etc/pccard_ether_remove
which haven't merge from PAO yet.
- Cosmetic changes.
MAKE_foo for things like MAKE_KERBEROS etc. Use that. I managed to
confuse myself last time and made make.conf different to the code. ;-(
Reported by: Jun Kuriyama <kuriyama@FreeBSD.org>
wheel to trash logfiles is not exactly good security policy. There have
been several gid wheel holes in ports. Various other files were changed
as well (eg: the locate database were set to more restrictive modes (444)
by their generation scripts) so this should be safe for them. utmp and
wtmp are mode 644 already on all the systems we checked.
Submitted by: jkb
Reviewed by: kris
Seems to work great in the type II cf<->pccard adapter that came with
the card. Others have reported with different chipsets for the pccard
bridge that additional support is needed to make this card work with
the 3.3 volts it needs.
o The Shining PMIDE-ASC card is also used in Road Warrior's Bullet Drive, so
add that to the comments.
o Eiger Lab's fujitsu based ethernet card: EPX-10BT (thanks to Ryan Losh for
donating the card to the cause).
o Add place holder entry for the 3Com Megahertz 3CXEM556. It doesn't work
yet, but that will change in time.
I've seen some script kiddie tools out there that fake the timestamps
but don't preserve the inode number.
Note - this will cause a lot of output the first time it is run!
PR: 18947
Reviewed by: Sheldon Hearn <sheldonh@uunet.co.za>
(I had been busy for my own research activity until the last weekend)
Supported devices:
SB Midi Port (sbc + midi)
SB OPL3 (sbc + midi)
16550 UART (midi, needs a trick in your hint)
CS461x Midi Port (csa + midi)
OSS-compatible sequencer (seq)
Supported playing software:
playmidi (We definitely need more)
Notes:
/dev/midistat now reports installed midi drivers. /dev/sndstat reports
only pcm drivers. We need the new name(pcmstat?).
EMU8000(SB AWE) does not sound yet but does get probed so that the OPL3
synth on an AWE card works.
TODO:
MSS/PCI bridge drivers
Midi-tty interface to support general serial devices
Modules
time, I have no idea if there is equivalence of printf. So, stf
setup still depends on /usr. In addition, prefix(8) and gifconfig(8)
are in /usr/sbin. Should we move these into /sbin?
- Sync with latest stf behavior. Latest stf doesn't have link-local
address. And, latest stf is not gif but stf.
produced human-readable output. I like this, but it's certainly not
something to change willy-nilly without discussion. Revert to -k.
Anyway, the new variable allows folks to pick any units flag that
fits their fancy.
the command-line arguments to be used for the call to df(1) when
daily_status_disks_enable is set to YES.
The name of the new variable was chosen by the maintainer of our
periodic hierarchy, Brian Somers.
PR: 19631
The only change in the default functionality should be that
the output reports are slightly more verbose WRT files deleted.
Not objected to by: freebsd-arch
options. This allows you to set the standard dynamic port
assignment range prior to any network daemons (like named) starting
up, necessary if you are also using a firewall to restrict lower ports.
will be MFC'd in a few days
world as was our old way, rather than when building a kernel.
Some people do not like the new way, and the release building still assumes
modules are built with the world.
of perl man pages and site_perl directories for alpha and i386 in /usr/local,
and share/aclocal and share/doc/ja in /usr/local and /usr/X11R6.
Reviewed by: the ports list
Approved by: steve (alpha part)
2. Newbusify the driver.
3. Build as a module.
4. Use correct minor numbers when creating device files.
5. Correctly lock control characters.
6. Return ENXIO when device not configured.
Submitted by: Tor Egge <Tor.Egge@fast.no>
7. Fix the baud_table.
Submitted by: Elliot Dierksen <ebd@oau.org>
Note:
- the old driver still lives in src/sys/i386/isa, so that you can
revert to it if something goes wrong.
- The module does not detach very well. Attaching works fine.
patches to work properly). These are the ones I managed to save since
the first of the year. While I tried to make sure all the entries
would work, some of them were converted by hand from the PAO entries.
MELCO LPC3-TX (Hiroshi Yamashita-san <bluemoon@msj.biglobe.ne.jp>)
Allied Telesis CentreCOM LA100-PCM-T V2
(hideaki yoshimura-san <Hideaki_Yoshimura@YAM-YAMASYS5.ccgw.nec.co.jp>)
Planex FNW-3600-T (Satoru Sawada-san <sawada@angel.ne.jp>)
Planex FNW-3700-T (Shigeru Ishida-san <ishida@isl.intec.co.jp>)
ADVANTECH COMpad-32/85 (Kuo Chun Fan-san) (one of two ports)
TDK DN1280R (Toshihisa Eto-san <eto@clave.gr.jp> and
<masahiro@inet.isogo.yokohama.jp> Masahiro Higuchi-san)
Panasonic TO-CAF56K FAX/Data Modem (katsutoshi ito
<itokatsu@mns.lsi.melco.co.jp>)
NTT DoCoMo (formerly NTT Personal) Paldio 611S (Yoshihiko SARUMARU-san
<mistral@imasy.or.jp>)
KME (TAXAN ICD-400PN, etc.) (ncv not in tree yet) (HASEGAWA-san Tomoki
<thasegawa@mta.biglobe.ne.jp>)
WORKBIT Ninja SCSI series (nsp not in tree yet) (HASEGAWA-san Tomoki
<thasegawa@mta.biglobe.ne.jp>)
SMC EtherEZ Combo (Masanori Takeishi-san <marina@yaya.forks.co.jp>)
KANSAI ELECTRIC KLA-PCM/T (Hideaki FUKUI-san <hideman@infosakyu.ne.jp>)
Plus Two cards from Kazuya Kodama-san <kodama@rd.nacsis.ac.jp> which
were in the last commit.
Added two ata devices (Kazuya Kodama <kodama@rd.nacsis.ac.jp> in nomads)
Added CyQ've ELA-110E (mihira-san <sanpei@sanpei.org>)
The CyQ card doesn't have a PR number (yet).
Fix D-Link 660 entry (PR 1340, Annelise Anderson)
Add more comments to very generic pcmcia ethernet card
entry (PR 17006, Georg Graf)
Add Linksys EtherFast 10/100 Intergrated PC Card (PCM100) (private mail
from Sean O'Connell)
PRs: 17006, 13402, 17992
batch the rest:
Add EXP DVD-780 DVD rom drive (brian reichert)
Generic cdrom (???)
Two modems eicon DIVA and com1 mc218 from oliver breuninger
Farallon SkyLINE (Dirk-Willem van Gulik)
Nits to the xe cards for xe driver!
maintained, and has been replaced by msun. The libm sources
shouldn't be removed just yet as there are parts that should be
merged into msun first.
PR: misc/17848
Discussed with: phk & bde
from the sys Makefile's SUBDIRs. This is conditioned in make.conf by the
NO_MODULES variable and the existence of the modules directory. The
actual location of the modules is not modified. Changes in Makefiles
only, this does not affect Peter's recent changes.
Reviewed by: Peter Wemm, who warned me I would get some flack, and
he had the good idea for the NO_MODULES variable.
/dev/xxx and one /dev/rxxx. This changes them to a hard link so that
less inodes are consumed and so that the permissions are always in sync.
There are lots more of these still.
scripts may use to source safely overrides in ${rc_conf_files}
files.
This protects users who insist on the bad practice of copying
/etc/defaults/rc.conf to /etc/rc.conf from a recursive loop
that exhausts available file descriptors.
Several people have expressed interest in breaking this function
out into its own shell script. Anyone who wants to embark on
such an undertaking would do well to study the attributed PR.
PR: 17595
Reported by: adrian
Submitted by: Doug Barton <Doug@gorean.org>
purpose of the hook was to provide the ability for a shell program to
instantiate the firewall rules instead of forcing them to be
statically coded. This functionality was already present through the
use of ${firewall_script}, and I see no need to keep the
${firewall_type} hook around.
Reminded by: Dag-Erling Smorgrav <des@freebsd.org>
symlinks to fd/0, fd/1, and fd/2 respectively. This will make
things easier for upcoming changes to fdesc (and does not break
anything for the current state of things) and hopefully its
position as the replacement for our existing static /dev/fd nodes.
Suggested (and reviewed) by: phk
of forcing them to be an 'ipfw' rules file. This allows one to
determine interface addresses dynamically, etc. The rule is if the
file referenced by ${firewall_type} is executable, it is sourced, but
if it is just readable, it is used as input to 'ipfw' like before.
for pccardd.
Please install /etc/defaults/pccard.conf and update /etc/defaults/rc.conf
as well.
Note that old pccard.conf.sample still remains for while but
no longer to be maintained.
Reviewed by: imp, -mobile ML and nomads ML in Japan.
reserve, in maximal NFS packets. Originally only 2 packets worth of
space was reserved. The default is now 4, which appears to greatly
improve performance for slow to mid-speed machines on gigabit networks.
Add documentation and correct some prior documentation.
Problem Researched by: Andrew Gallatin <gallatin@cs.duke.edu>
Approved by: jkh
have set me. This goes from now back to sometime in January 2000. Last
years' entries might result in more. But it will need to wait for another
time.
o XJEM3288 entry (Ron Rosson <insane@lunatic.oneinsane.net>)
o Fix Xircom CreditCard Modem 56 entry ("Juriy Goloveshkin <juriy@avias.com> ")
o Add pcmcia cd-rom entry from juriy as well, even though it doesn't work
o Add Intellegent Modem (sos)
o 3C562 entries (Marat Fayzullin <fms@cs.umd.edu>)
o Digiteam expresso modem (joerg_wunsch)
o RFI Hotline serial card (joerg_wunsch)
o EP401 Ethernet (jkoshy)
o Novatel wireless modem (nsayer)
o Intel modem 2400+ (aka US Roboitcs Worldport 14400) (sos)
o Option I18n GSM fax modem (markm)
o Toshiba SLIMV90 (roberto)
o Comment out display of fortune by default.
o Synch root's .cshrc/.login and non-root's .cshrc/.login in terms of
gratuitous variables set (EDITOR).
o Remove some commented out variables set inconsistently or gratuitously,
such as Interviews settings, 8-bit German locale for root only.
o Synchronize comments in header, as well as references to appropriate man
pages.
o Remove MANPATH setting as apparently /etc/manpath.config does all that
already.
Similar changes probably need to be made in other dot.* files for root
and skel, as all of these files seem to set different aliases, environmental
variables, prompts, and have different semantics.
As a result of this patch, leaving aside the setting of a special prompt
for root, users of csh and tcsh should find similar environments when
logging in or su'ing to any account using that shell.
Reviewed by: asmodai, nbm, will
On a K6-2/450 with fairly fast SCSI disks, building+installing src/share/
takes 2m51.3s, where src/share/doc/ is 1m9.9s of that.
However on a slow Alpha (233MHz) the times are 7m39.3s and 4m58.3s
respectively.
This commit allows one to speed up their build time, without not getting
any important and required changes if one used "NOSHARE".
driver that they use, followed by the MFG CIS string, followed by the
model CIS.
Future entries *WILL* follow this convention, or I'll be grumpy.
Please let me know if this messes anybody up. There were one or two
pentries that were duplicated. Some were removed since they were
identical, others were left in place.
Approved, in principle, by the nomads mailing list.
new sample database files, so that they will be installed with make
distribution. NOSPAM probably ought to be renamed to MAIL.
Reviewed by: peter
Approved by: jkh
as well as rename access.txt back to the standard access. Also modify
the Makefile to know how to build hashes for each of these databases.
If one of the databases is missing when Make is run, use a commented
out version of the sample.
Reviewed by: peter
Approved by: jkh
- 6to4(stf) interface configuration.
- Static route configuration.
- Comment additions.
- Replaced a still existed '@' to '%' in IPv6 scoped addr format.
(This became necessary as previous IPv6 scoped addr format change.)
Much thanks to ume, who helped me reviewing, testing, and finding problems
with these changes.
Approved by: jkh
Reviewed by: ume
to avoid error messages printed on /var/log/messages.
Recently added "stf" interface has IFF_MULTICAST bit set,
because IPv6 don't work on non IFF_MULTICAST set interfaces
in current implementation.
But "stf" interface is multi-dest IPv6 over IPv4 tunnel, so
can't treat multicast packet with no special configuration.
On the other hand, tools like "rtadvd", "pim6dd", "pim6sd"
send messages on IFF_MULTICAST set interfaces by default.
So there will be many bogus error message on /var/log/messages,
that multicast packets sent to "stf0" failed.
So,
-strip "stf0" from rtadvd sending interfaces in rc.network6
("rtadvd" is a daemon used only for local subnet, so it
will never need to send its packets over "stf0" interfaces.)
-Add default configuration files for "pim6dd" and "pim6sd",
and disable "stf0" in those files.
Approved by: jkh
modem side of my Xircom CreditCard Ethernet+Modem 33.6. Eliminate bad
Xircom entry. Complete IBM Push/Pop Modem(14.4 -> Push/Pop
Modem(14.4K).
Approved in concept by: jkh
o Correct Entry for Intel EtherExpress (jkoshy)
o Add Option International 56K modem (markm)
o Socket LP-E low power WinCE ethernet card (imp)
Correction approved by: jkh
Adding devices approved in principle by: jkh
