status register rather than 0. Without this, a single hardware volume
event triggers an interrupt storm.
- Implement hardware volume control for the Maestro chips. This version
only handles the case where both channels are adjusted at the same time.
Reviewed by: cg
- The mixer_hwmute() function can be called when a soundcard receives a
mute request.
- The mixer_hwstep() function can be used to adjust the volume of one or
both channels.
- The 'hw.snd.hwvol_step' sysctl determines the amount that mixer_hwstep()
adjusts the volume by on each call.
- The 'hw.snd.hwvol_mixer' sysctl specifies the mixer device to adjust the
volume on for both functions. The values used correspond to the
SOUNDCARD_MIXER_* constants.
want according to the modes set with the ppc(4) flags. Especially, it
should fix some problems with mode detection of parallel chipsets
configured to EPP but which have timing troubles with the drives. In such
a case, the driver should now fall back to slower modes (PS2, NIBBLE).
WWNs correctly (Again!) - this time for the case that we're not going
to fully init the adapter if isp_init is called (with ISP_CFG_NOINIT
set in options). The pupose for this is to bring the adapter up to
almost ready to go, get info out of NVRAM, but to not start it up- leaving
it until later to actually start things up if wanted (and possibly with
different roles selected).
with the driver locking up under load.
- Restructure so that we use a static pool of commands/FIBs, rather than
allocating them in clusters. The cluster allocation just made things
more complicated, and allowed us to waste more memory in peak load
situations.
- Make queueing macros more like my other drivers. This adds queue stats
for free. Add some debugging to take advantage of this.
- Reimplement the periodic timeout scan. Kick the interrupt handler
and the start routine every scan as well, just to be safe. Track busy
commands properly.
- Bring resource cleanup into line with resource allocation. We should
now clean up correctly after a failed probe/unload/etc.
- Try to start new commands when old ones are completed. We weren't doing
this before, which could lead to deadlock when the controller was full.
- Don't try to build a new command if we have found a deferred command.
This could cause us to lose the deferred command.
- Use diskerr() to report I/O errors.
- Don't bail if the AdapterInfo structure is the wrong size. Some variation
seems to be normal. We need to improve our handing of 2.x firmware sets.
- Improve some comments in an attempt to try to make things clearer.
- Restructure to avoid some warnings.
o Move the ax88190 code to its own function.
o Move all device_method_t, driver_t and DRIVER_MODULE definitions to the
end of files.
o Wrap a few lines > 80 characters.
o Use the same devclass for all ed drivers. This allows machines with
multiple types of cards to have their cards numbered correctly. Before,
you could wind up with two ed0's.
o Protect if_edvar.h from multiple includes because I was there.
modify chn_setblocksize() to pick a default soft-blocksize appropriate to the
sample rate and format in use. it will aim for a power of two size small
enough to generate block sizes of at most 20ms. it will also set the
hard-blocksize taking into account rate/format conversions in use.
update drivers to implement setblocksize correctly:
updated, tested: sb16, emu10k1, maestro, solo
updated, untested: ad1816, ess, mss, sb8, csa
not updated: ds1, es137x, fm801, neomagic, t4dwave, via82c686
i lack hardware to test: ad1816, csa, fm801, neomagic
others will be updated/tested in the next few days.
This is because calls with M_WAIT (now M_TRYWAIT) may not wait
forever when nothing is available for allocation, and may end up
returning NULL. Hopefully we now communicate more of the right thing
to developers and make it very clear that it's necessary to check whether
calls with M_(TRY)WAIT also resulted in a failed allocation.
M_TRYWAIT basically means "try harder, block if necessary, but don't
necessarily wait forever." The time spent blocking is tunable with
the kern.ipc.mbuf_wait sysctl.
M_WAIT is now deprecated but still defined for the next little while.
* Fix a typo in a comment in mbuf.h
* Fix some code that was actually passing the mbuf subsystem's M_WAIT to
malloc(). Made it pass M_WAITOK instead. If we were ever to redefine the
value of the M_WAIT flag, this could have became a big problem.
