PCG-505BX (for example) has one of those:
wi0: <Intersil Prism3> mem 0xf8000000-0xf8000fff at device 2.0 on pci2
wi0: 802.11 address: 00:02:8a:94:d8:73
wi0: using RF:PRISM3(Mini-PCI)
wi0: Intersil Firmware: Primary (1.1.1), Station (1.5.6)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
has the same product id, but different vendor id. It also appears
that the MELCO's id should be 0x18a instead of 0x8a01. Fix this.
Submitted by: Shizuka Kudo-san
and up commands. When configuring the interface down only the
connections that are currently closing are deleted from the connection
table. When the interface is configured up, all connections that
are in the table are re-opened.
connections that have been open (and were not closing) when
the interface was stopped. This makes the behaviour of fatm(4) more like
the behaviour of en(4).
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
- Build SGL's for ATA_PASSTHROUGH commands
- Fallback to using the sgl_offset when the opcode is unknown for building
SGL's/
- Add ioctl calls for adding and removing units.
- Define previously undefined AEN's
- Allocate memory for the ioctl payload in multiples of 512bytes.
MFC after: 1 week
preparation for supporting the OPENVCC and CLOSEVCC ioctls which
are needed for ng_atm. This required some re-organisation of the code
(mostly converting array indexes to pointers). This also gives us
an array of open vccs that will help in using the generic GETVCCS handler.
the macro definition, and cause the generation of syntactically
incorrect code that gcc happens to accept.
Reviewed by: schweikh (mentor)
MFC after: 4 weeks
larger than normal frames, to account for the case where a bge(4) NIC
is used with VLANs. Since we set the IFCAP_VLAN_MTU flag, we must allow
reception of frames up to 1522 bytes in size rather than 1518.
Note that it is possible to work around this bug by doing:
# ifconfig bge0 mtu 1504
prior to configuring any VLAN interfaces.
recompiling the driver. See the comments near the top of "if_em.h"
for descriptions of these delays. Four new loader tunables control
the system-wide default values:
hw.em.tx_int_delay
hw.em.rx_int_delay
hw.em.tx_abs_int_delay
hw.em.rx_abs_int_delay
The tunables are specified in microseconds. The valid range is
0-67108 usec., and 0 means that the timer is disabled.
There are also four new sysctls (actually, a set of four for each
"em" device in the system) to query and change the interrupt delays
after the system is up:
hw.em0.tx_int_delay
hw.em0.rx_int_delay
hw.em0.tx_abs_int_delay (not present for 82542/3/4 adapters)
hw.em0.rx_abs_int_delay (not present for 82542/3/4 adapters)
It seems to be OK to change these values even while the adapter is
passing traffic.
Approved by: Prafulla Deuskar <pdeuskar@FreeBSD.ORG>
MFC after: 4 weeks
