Switch the now added E5573Cs322_ECM (0x14db) as well per default to NCM.
With this patch we default all devices to simple NCM mode to avoid the
problem and get a consistent reliable behavior. No matter what firmware
version and provider mix are involved.
Rationale:
Even the bigger SOC shows under complex load in ECM (double-nat) mode
the same performance drop from 25Mbit to 2Mbit Line Speed, similar to E3372h.
Reason: Thermal problems (reported via serial debug interface in ACM Mode)
after 2-3 minutes load.
Fix the root cause and bundle a working firmware is out of reach because
Huawei sells the same hardware, different (crippled) firmware versions
at different price points in different markets as strategy.
Reviewed by: imp
Pull Request: https://github.com/freebsd/freebsd-src/pull/633
Add initialization for new Huawei 4G E3372_NCM, E3372v153_NCM,
E5573Cs322_NCM, E5573Cs322_ECM, and E5573Cs322_ACM.
Remove now-obsolete Huawei 3G E3131 init sequence. These devices are
obsolete, share IDs with new devices and the 3G networks are shutdown.
These old devices work correctly via the 4G code while still allowing
the shared IDs to work differently for the new devices.
Reviewed by: imp
Pull Request: https://github.com/freebsd/freebsd-src/pull/633
We can now set promisc and allmulti modes.
Filtering of given multicast addresses is not supported.
Changing the mode is done by sending a command described in:
"USB CDC Subclass Specification for Ethernet Devices v1.2, section 6.2.4".
This means that at least in theory this feature should work with all
modems that are using this driver.
This fixes Huawei E3372h-320 running new firmware in "HiLink" mode.
Previously it would reset a few seconds after its mode was changed
with "usb_modeswitch".
Setting RX filter to default value at the end of attach function
fixed that.
Sponsored by: Stormshield
Obtained from: Semihalf
Differential revision: https://reviews.freebsd.org/D31766
MFC after: 2 weeks
Reviewed by: hps
This makes it more usable in that dhclient will autolaunch from devd
now when cdce devices are plugged in.. It also sets the baudrate, but
this isn't exported via tools, and CDCE doesn't have a good way to
specify the media type, so there isn't a good way to tell userland
what the speed is currently...
Reviewed by: hps
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D30625
Since then, the FreeBSD USB stack has got proper USB RNDIS support.
PR: 254345
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked). Use it in
preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Reviewed by: hselasky, kib
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D23632
rename the source to gsb_crc32.c.
This is a prerequisite of unifying kernel zlib instances.
PR: 229763
Submitted by: Yoshihiro Ota <ota at j.email.ne.jp>
Differential Revision: https://reviews.freebsd.org/D20193
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
Initially, only tag files that use BSD 4-Clause "Original" license.
RelNotes: yes
Differential Revision: https://reviews.freebsd.org/D13133
tables. Some drivers needed some slight re-arrangement of declarations
to accommodate this. Change the USB pnp tables slightly to allow
better compatibility with the system by moving linux driver info from
start of each entry to the end. All other PNP tables in the system
have the per-device flags and such at the end of the elements rather
that at the beginning.
Differential Review: https://reviews.freebsd.org/D3458
The mbuf length fields must be set before m_adj() is called else
m_adj() will not always adjust the mbuf and an unaligned read
exception can trigger inside the network stack. This can happen on
platforms where unaligned reads are not supported. Adjust a length
check to include the 2-byte ethernet alignment while at it.
MFC after: 3 days
This makes Mac OS X happy when it returns back from suspending.
o Switch notify state after data is transferred, but not before.
o Consider there is also Super Speed mode.
o Do not set stall bit on any pipes in device mode as Mac OS X seems
don't support it.
In collaboration with: hselasky@
Required when communicating to Mac OS X USB host stack.
o Also don't set stall bit to TX pipe in device mode as seems Mac OS X
don't clears it as it should.
Discussed with: hselasky@
E5372 with different product IDs.
Interestingly, the standard E5372 IDs (12d1:1506) are currently listed in
u3g.c and are the same as the E3131. However, the R215/E5372 is an NCM
device and works well with cdce(4) whereas the E3131 isn't. More work
may be needed to better identify the other device IDs.
MFC after: 1 week
ethernet class.
Note: This is untested as I do not have a device like this. That is
reflected in the MFC timeout.
PR: 192345
Submitted by: rozhuk.im gmail.com
MFC after: 4 weeks
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
sorted according to the mode which they support:
host, device or dual mode
- Add generic tool to extract these data:
tools/bus_autoconf
Discussed with: imp
Suggested by: Robert Millan <rmh@debian.org>
PR: misc/157903
MFC after: 14 days
- correct the ethernet payload remainder which
must be post-offseted by -14 bytes instead of
0 bytes. This is not very clearly defined in the
NCM specification.
- add development feature about limiting the
maximum datagram count in each NCM payload.
- zero-pad alignment data
- add TX-interval tuning sysctl
Approved by: thompsa (mentor)
greater than 65535 bytes then the CDC driver might not work as expected, which
is not likely with the existing USB speeds.
Submitted by: Hans Petter Selasky
message has been printed is enough to get someones attention. Also remove the
line number for DPRINTF/DPRINTFN, it already prints the funtion name and a
unique message.
- Add support for devices that handle set and clear stall in hardware.
- Add missing get timestamp function
- Add more xfer flags
Submitted by: Hans Petter Selasky
Approved by: re (kib)
