adapter list still capable, but only PCI-E adapters are now enabled.
The user can enable older PCI-X or PCI adapters using ifconfig.
Secondly, Arthur Hartwig pointed out my MSI change was not working
correctly, changed to something that now does. Thanks Arthur.
There was also a fundamental bug in the 82575 MSIX code, the MSIX
registers had to be mapped, opps :)
Rubber-stamped by: Pdeuskar
the power_nodriver tunable is off. pci_cfg_save() already checks the
tunable internally, and no other callers of pci_cfg_save() check the
tunable.
Reviewed by: imp
- Updated firmware to latest release (v3.4.8) to fix TSO + jumbo frame lockup
- Added MSI (hw.bce.msi_enable) and TSO (hw.bce.tso_enable) sysctls
- Fixed kernel panic when MSI is used and module is unloaded
- Added several new debug routines
- Removed slack space for RX/TX chains since it only covers sloppy coding
- Fixed a potential problem when programming jumbo MTU size in hardware
- Various other comment changes
MFC after: 4 weeks
because on at least my dc based cards there's garbage in there. The
recent changes in the resource code appears to have unmasked this
problem... At least dc now probes/attaches better than it did before.
Also, we no longer need to write to the cfg for the other registers.
legacy codepath match the 82575, without this we were seeing bridging
fail on 82546 adapters. Secondly, I have limited TSO to PCI Express
adapters, I meant to do this and it got dropped in the earlier delta.
Next, I am dropping in the latest shared code from our development
team, consensus was that this should be done frequently, so I am :)
Approved by: pdeuskar
This patch does the following:
- Remove un-necessary code that is not even compiling into the driver
under TW_OSL_NON_DMA_MEM_ALLOC_PER_REQUEST defines.
- Remove bundled firmware image and associated "files" entry for tw_cl_fwimg.c
- Remove bundled firmware flashing routines. We now have tw_update userspace
FreeBSD controller flash utility.
- Fix driver crash on load due to shared interrupt.
- Fix 2 lock leaks for Giant lock.
- Fix CCB leak.
- Add support for 9650SE controllers.
Many thanks to 3Ware/AMCC for continuing to support FreeBSD.
time workaround for problems with 82571 adapters and LAAs, one port
getting reset can cause the other to have its RAR[0] also reset,
thus overwriting an LAA. This fix works around it by also keeping
the address in the last array member.
The other bug is specific to the new 575 adapter, its transmit code
logic in handling hwassists was too crude, it broken when doing
bridges. I am much happier with the new logic,we may want to change
the legacy path at some point to something similar.
Reviewed by: pdeuskar
Approved by: pdeuskar
- Update to latest (1.4.17) firmware.
- Use the new MXGEFW_CMD_UNALIGNED_TEST (added in firmare 1.4.16) to
have the firmware tell us if the PCIe chipset supports aligned PCIe
completions.
- Hard to maintain, and frequently out of date whitelist of PCIe
chipsets known to produce aligned completions removed, as it has been
replaced in its role of selecting the correct firmware to run by the
use of MXGEFW_CMD_UNALIGNED_TEST.
- Break the dma test out of mxge_reset() and into its own function
(mxge_dma_test()) so it can be used by both the normal DMA test, and
to run the unaligned test.
- Improved support for enabling ECRCs
Sponsored by: Myricom Inc.
Seems to work on RELENG_4 through -current and also on sparc64
now. There may still be some issues with the auto attach/detach
code to sort out.
MFC after: 3 days
- http://www.intel.com/design/chipsets/specupdt/245051.htm
AC97 Soft Audio and Soft Modem Master Abort Errata
Issue:
Use of either soft audio or soft modem on an Intel® 82443MX PCISet
based platform running a 100 MHz Processor System Bus and an AC97 codec
may result in failures. The system continues to function normally while
the AC97 hardware may not resume and may require a cold-boot to
recover. As a result of the failure, the Master Abort Status bit will
be set in the audio or modem function PCI header space.
Workaround:
Force uncacheable DMA on both BDL and pcm buffers.
Tested by: Emil Holmstr|m <emil@linux.se>
- Remove explicit call to pmap_change_attr(), since we now have proper
and functional definition of BUS_DMA_NOCACHE.
- Enable PCI(e) bus snooping for non i386/amd64 as an alternative for
uncacheable DMA.
- Codecs changes:
* Analag Device -> Analog Devices, AD1988.
* New codec: VIA VT1708 and VT1709, Realtek ALC262, ALC861-VD and
ALC885.
* Various fixups for Conexant Waikiki, fix recording (read: microphone)
on various Analog Devices codecs due to vendor BIOS mess, various
quirks for several ASUS laptops/boards.
- Fix connection list handling, closely following the specification to
handle range of nids.
- Basic Jack sense polling infrastructure for possible hardwares with
broken unsolicited response interrupt.
Ideas/Submitted/Tested by: Andriy Gapon <avg@icyb.net.ua>,
#freebsd-azalia, many.
Updated copyright date to 2007.
Tested with BCM5706 A3.
Added ID for BCM5708 B2.
Removed unused driver version string.
Modified BCE_PRINTF macro to automatically fill-in the sc pointer.
Fixed a kernel panic when the driver was loaded as a module from the
command-line because the MII bus pointer was null (i.e. the MII bus
hadn't been enumerated yet).
Added fix proposed by Vladimir Ivanov <wawa@yandex-team.ru> to prevent
driver state corruption when releasing the lock during the ISR in
bce_rx_intr() to send packets up the stack.
Added new TX chain and register read sysctl interfaces for debugging.
Cleaned up formatting for various other debug routines.
Added a new statistic maintained by firmware which tracks the number
of received packets dropped because no receive buffers are available.
correct network drivers with respect to busmaster DMA, go over it
with at duster to make other aspects of it a role model:
Eliminate the pci specific softc, it serves no rational purpose.
Use convenience resource allocation/deallocation functions to save
code and errorhandling.
Switch from bus_space_{read|write}_%u() to bus_{read|write}_%u()
functions and forget about tags and handles, the resource will know
about those, should they be needed. This also eliminates a number
of inconsistently named local variables.
in comments for .c and .h files respectively. Jack may want to clean up
style or other aspects once he's up and about again, but this gets the
kernel compiling.
shared code infrastructure that is family specific and
modular. There is also support for our latest gigabit
nic, the 82575 that is MSI/X and multiqueue capable.
The new shared code changes some interfaces to the core
code but testing at Intel has been going on for months,
it is fairly stable.
I have attempted to be careful in retaining any fixes that
CURRENT had and we did not, I apologize in advance if any
thing gets clobbered, I'm sure I'll hear about it :)
Approved by pdeuskar
- Simplify the amount of work that has be done for each architecture by
pushing more of the truly MI code down into the PCI bus driver.
- Don't bind MSI-X indicies to IRQs so that we can allow a driver to map
multiple MSI-X messages into a single IRQ when handling a message
shortage.
The changes include:
- Add a new pcib_if method: PCIB_MAP_MSI() which is called by the PCI bus
to calculate the address and data values for a given MSI/MSI-X IRQ.
The x86 nexus drivers map this into a call to a new 'msi_map()' function
in msi.c that does the mapping.
- Retire the pcib_if method PCIB_REMAP_MSIX() and remove the 'index'
parameter from PCIB_ALLOC_MSIX(). MD code no longer has any knowledge
of the MSI-X index for a given MSI-X IRQ.
- The PCI bus driver now stores more MSI-X state in a child's ivars.
Specifically, it now stores an array of IRQs (called "message vectors" in
the code) that have associated address and data values, and a small
virtual version of the MSI-X table that specifies the message vector
that a given MSI-X table entry uses. Sparse mappings are permitted in
the virtual table.
- The PCI bus driver now configures the MSI and MSI-X address/data
registers directly via custom bus_setup_intr() and bus_teardown_intr()
methods. pci_setup_intr() invokes PCIB_MAP_MSI() to determine the
address and data values for a given message as needed. The MD code
no longer has to call back down into the PCI bus code to set these
values from the nexus' bus_setup_intr() handler.
- The PCI bus code provides a callout (pci_remap_msi_irq()) that the MD
code can call to force the PCI bus to re-invoke PCIB_MAP_MSI() to get
new values of the address and data fields for a given IRQ. The x86
MSI code uses this when an MSI IRQ is moved to a different CPU, requiring
a new value of the 'address' field.
- The x86 MSI psuedo-driver loses a lot of code, and in fact the separate
MSI/MSI-X pseudo-PICs are collapsed down into a single MSI PIC driver
since the only remaining diff between the two is a substring in a
bootverbose printf.
- The PCI bus driver will now restore MSI-X state (including programming
entries in the MSI-X table) on device resume.
- The interface for pci_remap_msix() has changed. Instead of accepting
indices for the allocated vectors, it accepts a mini-virtual table
(with a new length parameter). This table is an array of u_ints, where
each value specifies which allocated message vector to use for the
corresponding MSI-X message. A vector of 0 forces a message to not
have an associated IRQ. The device may choose to only use some of the
IRQs assigned, in which case the unused IRQs must be at the "end" and
will be released back to the system. This allows a driver to use the
same remap table for different shortage values. For example, if a driver
wants 4 messages, it can use the same remap table (which only uses the
first two messages) for the cases when it only gets 2 or 3 messages and
in the latter case the PCI bus will release the 3rd IRQ back to the
system.
MFC after: 1 month
pointers. A structure is more readable and less error-prone. It
also avoids problems when a function pointer doesn't have the
same width as a void pointer.
sc->mii_anegticks according to whether the respective BGE chip
supports Fast Ethernet only or also Gigabit Ethernet.
- At least the BGE chips I've tested with wedge when isolating them
so document this as the reason for setting MIIF_NOISOLATE and
remove the unused (and partially even #ifdef'ed out) isolation
related code. Add code that panics if we encounter a non-zero MII
instance as generally there's no way a PHY requiring MIIF_NOISOLATE
can be handled gracefully in a multi-PHY configuration (it's ok for
the internal PHY of single-PHY-only-NIC to not support isolation
though).
- Additionally set MIIF_NOLOOP as loopback doesn't seem to work
either and remove the #ifdef'ed out code for adding respective
media. The MIIF_NOLOOP flag currently triggers nothing but
hopefully will be respected by mii_phy_setmedia() later on.
Reviewed by: jkim, yongari
MFC after: 1 month
Blade 2500, Fire V210 and probably some other sparc64 machines.
These chips are typically not fitted with an EEPROM which means
that we have to obtain the MAC address via OFW and that some chip
tests will just always fail.
These changes are based on the respective code found in OpenBSD
with some additional info obtained from OpenSolaris and some style
suggestions by jkim@. They also have the desired side-effect of
respecting the 'local-mac-address?' system configuration variable
for the affected BGEs.
- In bge_attach() factor out calling bge_release_resources() before
going to the fail label into the fail label as well as replace a
magic 6 with ETHER_ADDR_LEN.
Reviewed by: yongari (before style changes), jkim
- Wake up DMA engine after adding a new receive buffer.
- Skip buffers which have unknown state after error.
- More rigid error detection.
MFC after: 1 week
as some combinations of chipset, controller and target do not behave
correctly when DMA is enabled for other commands.
PR: kern/103602
MFC after: 2 weeks
were never freed, but the big ring was freed twice.
-Don't supply rx hw csums for frames which are padded beyond the
length specified in the ip header. If the padding is non-zero,
the hw csum will be incorrect for such frames.
Sponsored by: Myricom
This workaround the problem in Parallels/VMWare where the emulated drivers are
slower, especially with ATA_FLUSHCACHE. The problem appears much more
frequently with ZFS which use it a lot more.
Approved: sos, pjd
specific request and thus should first try to be allocated from the
sys_resource pool. This avoids using the sys_resource pool for wildcard
requests that have bounded ranges coming from cbb(4) and Host-PCI pcib(4)
drivers.
Tested by: Andrea Bittau <a.bittau of cs.ucl.ac.uk fame>
Sleuthing by: Andrea Bittau as well
that the MSI mapping window is fixed at 0xfee00000 and the capability
does not include two more dwords used to program the address. Supporting
this mostly results in quieting spurious warnings during boot about
non-default MSI mapping windows.
- HT 2.00b also added a new HT capability type, so support that in pciconf.
MFC after: 3 days
Tested by: jmg
It seems that valid pause frames(Tx flow control) cause GMAC to hang
such that it resulted in watchdog timeout. As a work around don't
flush Rx MAC FIFO if we've received pause frames.
Tested by: Harald Schmalzbauer (h DOT schmalzbauer AT omnisec DOT de)
Under certain circumtances, if TSO is active, Yukon II generates
corrupted IP packets. All corrupted IP packets I noticed were the the
last segmented packet in a TSO request. The corrupted packet resulted
in retransmission of the damaged packet which in turn decreased network
performance dramatically.
Unfortunately it seems that there is no way to workaround this bug
as TSO is completely handled in hardware. Disable TSO until we find a
working workaround or a new silicon revision that doesn't have this
hardware bug.
supports software encrypt/decrypt.
The nuked code itself is quite problematic, as pointed out by sam@ ---
wk->wk_keyix should be replaced by the loop count.
Tested with WEP/TKIP/CCMP/no-protection.
Approved by: sam@ (mentor)
Noticed by: Hans Petter Selasky <hselasky@c2i.net>
