Partial merge r198987:
Use device_printf() and if_printf() instead of printf() with an explicit
unit number and remove 'unit' members from softc.
Partial merge r199414:
Use the bus_*() routines rather than bus_space_*() for register operations.
r199543:
Several fixes to this driver:
- Overhaul the locking to avoid recursion and add missing locking in a few
places.
- Don't schedule a task to call vge_start() from contexts that are safe to
call vge_start() directly. Just invoke the routine directly instead
(this is what all of the other NIC drivers I am familiar with do). Note
that vge(4) does not use an interrupt filter handler which is the primary
reason some other drivers use tasks.
- Add a new private timer to drive the watchdog timer instead of using
if_watchdog and if_timer.
- Fixup detach by calling ether_ifdetach() before stopping the interface.
r200422:
Remove driver lock assertion in MII register access. This change
was made in r199543 to remove MTX_RECURSE. These routines can be
called in device attach phase(e.g. mii_phy_probe()) so checking
assertion here is not right as caller does not hold a driver lock.
Set the locally-assigned bit in the randomly generated Ethernet address
if we end up having to generate one.
PR: kern/133239
Discussed with: yongari
Approved by: ed (mentor, implicit)
r200088:
Add workaround to overcome hardware limitation which allows only a
single outstanding DMA read operation. Most controllers targeted to
client with PCIe bus interface(e.g. BCM5761) may have this
limitation. All controllers for servers does not have this
limitation.
Collapsing mbuf chains to reduce number of memory reads before
transmitting was most effective way to workaround this. I got about
940Mbps from 850Mbps with mbuf collapsing on BCM5761. However it
takes a lot of CPU cycles to collapse mbuf chains so add tunable to
control the number of allowed TX buffers before collapsing. The
default value is 0 which effectively disables the forced collapsing.
For most cases 2 would yield best performance(about 930Mbps)
without much sacrificing CPU cycles.
Note the collapsing is only activated when the controller is on
PCIe bus and the frame does not need TSO operation. TSO does not
seem to suffer from the hardware limitation because the payload
size is much bigger than normal IP datagram.
Thanks to davidch@ who told me the limitation of client controllers
and actually gave possible workarounds to mitigate the limitation.
r200227:
Remove PHY isolate/power down code in bge_stop(). The isolation
handler in brgphy(4) does not exist and brgphy(4) just resets the
PHY and returns EINVAL as it has no isolation handler. I also agree
on Marius's opinion that stop handler of every NIC driver seems to
be the wrong place for implementing PHY isolate/power down.
If we need PHY isolate/power down it should be implemented in
brgphy(4) and users should administratively down the PHY.
r200228:
Don't access jumbo frame related registers if controller lacks the
feature. These registers are reserved on controllers that have no
support for jumbo frame.
Only BCM5700 has mini ring so do not poke mini ring related
registers if controller is not BCM5700.
r200246:
Partially revert r200228. For mini RCB case, bge(4) still have to
disable mini ring withtout regard to mini ring support.
r200264:
Create sysctl node(dev.bge.%d.focred_collapse) instead of
hw.bge.forced_collapse. hw.bge.forced_collapse affects all bge(4)
controllers on system which may not desirable behavior of the
sysctl node. Also allow the sysctl node could be modified at any
time.
r201446:
Fix regression introduced in r198318. BCM5754/BCM5754M uses the
same ASIC ID of BCM5758 such that r198318 incorecctly enabled TSO
on BCM5754.BCM5754M controllers. BCM5754/BCM5754M needs a special
firmware to enable TSO and bge(4) does not support firmware based
TSO.
r199670:
Fix two long standing bugs on bge(4). Most pre BCM5755 controllers
have a DMA bug when buffer address crosses a multiple of the 4GB
boundary(e.g. 4GB, 8GB, 12GB etc). Limit DMA address to be within
4GB address for these controllers. The second DMA bug limits DMA
address to be within 40bit address space. This bug applies to
BCM5714 and BCM5715 and 5708(bce(4) controller). This is not
actually a MAC controller bug but an issue with the embedded PCIe
to PCI-X bridge in the device. So for BCM5714/BCM5715 controllers
also limit the DMA address to be within 40bit address space.
Special thanks to davidch@ who gave me detailed errata information.
I think this change will fix long standing bge(4) instability
issues on systems with more than 4GB memory.
r199671:
Implement TSO for BCM5755 or newer controllers. Some controllers
seem to require a special firmware to use TSO. But the firmware is
not available to FreeBSD and Linux claims that the TSO performed by
the firmware is slower than hardware based TSO. Moreover the
firmware based TSO has one known bug which can't handle TSO if
ethernet header + IP/TCP header is greater than 80 bytes. The
workaround for the TSO bug exist but it seems it's too expensive
than not using TSO at all. Some hardwares also have the TSO bug so
limit the TSO to the controllers that are not affected TSO issues
(e.g. 5755 or higher).
While I'm here set VLAN tag bit to all descriptors that belengs to
a frame instead of the first descriptor of a frame. The datasheet
is not clear how to handle VLAN tag bit but it worked either way in
my testing. This makes it simplify TSO configuration a little bit.
Big thanks to davidch@ who sent me detailed TSO information.
Without this I was not able to implement it.
r199674:
Add missing function prototype in r199671.
r199679:
Reduce status block size DMAed by controller. bge(4) uses single
Tx/Rx/Rx return ring such that large part of status block was not
used at all. All bge(4) controllers except BCM5700 AX/BX has a
feature to control the size of status block. So use minimum status
block size allowed in controller. This reduces number of DMAed
status block size to 32 bytes from 80 bytes.
r199761:
BGE_FLAG_40BIT_BUG should be set before creating DMA tags.
r199807:
Make sure one shot MSI is enabled.
r199808:
Fix typo which inversed the logic which in turn disabled MSI.
r199667:
Cache Rx producer/Tx consumer index as soon as we know status block
update and then clear status block. Previously it used to access
these index without synchronization which may cause problems when
bounce buffers are used. Also add missing bus_dmamap_sync(9) in
polling handler. Since we now update status block in driver, adjust
bus_dmamap_sync(9) for status block.
r199668:
For MSI case, interrupt is not shared and we don't need to force
PCI flush to get correct status block update. Add an optimized
interrupt handler that is activated for MSI case. Actual interrupt
handling is done by taskqueue such that the handler does not
require driver lock for Rx path. The MSI capable bge(4) controllers
automatically disables further interrupt once it enters interrupt
state so we don't need PIO access to disable interrupt in interrupt
handler.
r199663:
Due to newly added PCIe capabilities fallback code for finding the
PCIe capability did not work right on recent controllers. Remove
FreeBSD 6.x support code.
r199664:
Use capability pointer to access PCIe registers rather than
directly access them at fixed address. While I'm here don't touch
other bits of PCIe device control register except max payload size.
r199665:
Controller does not write Rx descriptors, remove BUS_DMASYNC_PREREAD.
r199666:
Rearrange bge_start_locked to see we can send more frames by
checking IFF_DRV_RUNNING and IFF_DRV_OACTIVE flags. Also if we
have less than 16 free send BDs set IFF_DRV_OACTIVE and try it
later. Previously bge(4) used to reserve 16 free send BDs after
loading dma maps but hardware just need one reserved send BD. If
prouder index has the same value of consumer index it means the Tx
queue is empty.
While I'm here check IFQ_DRV_IS_EMPTY first to save one lock
operation.
r199065:
Correct disabling checksum offloading for BCM5700 B0.
r199115:
Add missing bus_dmamap_sync(9) before issuing kick command.
r199116:
Zero out Tx/Rx descriptors before using them. Also add missing
bus_dmamap_sync(9) after Tx descriptor initialization.
r199153:
Controller does not update Tx descriptors(send BDs) after sending
frames so remove unnecessary BUS_DMASYNC_PREREAD and
BUS_DMASYNC_POSTREAD of bus_dmamap_sync(9).
r199661:
Remove extra white space.
r199662:
Fix typo introduced in r199011.
r198967:
Correct MSI mode register bits.
r199009:
bge(4) already switched to use UMA backed page allocator and local
memory allocator for jumbo frame was removed long time ago. Remove
no more used macros.
r199010:
Do bus_dmamap_sync call only if frame size is greater than
standard buffer size. If controller is not capable of handling
jumbo frame, interface MTU couldn't be larger than standard MTU
which in turn the received should be fit in standard buffer. This
fixes bus_dmamap_sync call for jumbo ring is called even if
interface is configured to use standard MTU.
Also if total frame size could be fit into standard buffer don't
use jumbo buffers.
r199011:
Reimplement Rx buffer allocation to handle dma map load failure.
Introduce two spare dma maps for standard buffer and jumbo buffer
respectively. If loading a dma map failed reuse previously loaded
dma map. This should fix unloaded dma map is used in case of dma
map load failure. Also don't blindly unload dma map and defer
dma map sync and unloading operation until we know dma map for new
buffer is successfully loaded. This change saves unnecessary dma
load/unload operation. Previously bge(4) tried to reuse mbuf
with unloaded dma map which is really bad thing in bus_dma(9)
perspective.
While I'm here update if_iqdrops if we can't allocate Rx buffers.
r199014:
Fix I mssied in r199011. Rx ring index also should be updated.
If we fill Rx ring full instead of half we can simplify this logic
but this requires more experimentation.
r199020:
Tell upper layer we support long frames. ether_ifattach()
initializes it to ETHER_HDR_LEN so we have to override it after
calling ether_ifattch().
While I'm here remove setting if_mtu value, it's initialized in
ether_ifattach().
r199035:
Don't count input errors twice, we always read input errors from
MAC in bge_tick. Previously it used to show more number of input
errors. I noticed actual input errors were less than 8% even for
64 bytes UDP frames generated by netperf.
Since we always access BGE_RXLP_LOCSTAT_IFIN_DROPS register in
bge_tick, remove useless code protected by #ifdef notyet.
r199036:
Count number of inbound packets which were chosen to be discarded
as input errors. Also count out of receive BDs as input errors.
r199054:
Partially revert r199035.
Revision 1.158 says only lower ten bits of
BGE_RXLP_LOCSTAT_IFIN_DROPS register is valid. For BCM5761 case it
seems the controller maintains 16bits value for the register.
However 16bits are still too small to count all dropped packets
happened in a second. To get a correct counter we have to read the
register in bge_rxeof() which would be too expensive.
r198923:
Use correct dma tag for jumbo buffer.
r198924:
Covert bge_newbuf_std to use bus_dmamap_load_mbuf_sg(9). Note,
bge_newbuf_std still has a bug for handling dma map load failure
under high network load. Just reusing mbuf is not enough as driver
already unloaded the dma map of the mbuf. Graceful recovery needs
more work.
Ideally we can just update dma address part of a Rx descriptor
because the controller never overwrite the Rx descriptor. This
requires some Rx initialization code changes and it would be done
later after fixing other incorrect bus_dma(9) usages.
r198927:
Remove common DMA tag used for TX/RX mbufs and create Tx DMA tag
and Rx DMA tag separately. Previously it used a common mbuf DMA tag
for both Tx and Rx path but Rx buffer(standard ring case) should
have a single DMA segment and maximum buffer size of the segment
should be less than or equal to MCLBYTES. This change also make it
possible to add TSO with minor changes.
r198928:
Make bge_newbuf_std()/bge_newbuf_jumbo() returns actual error code
for buffer allocation. If driver know we are out of Rx buffers let
controller stop. This should fix panic when interface is run even
if it had no configured Rx buffers.
Support the tablet in (at least) the Toshiba Portege M200 Tablet PC.
This device only appears on the ACPI bus, so isn't caught by the current
entry for it in the uart(4) ISA attachment.
PR: kern/140172
Reviewed by: jhb, marcel
Approved by: ed (mentor, implicit)
- Try pre-allocating all FIBs upfront. Previously we tried pre-allocating
128 FIBs first and allocated more later if necessary. Remove now unused
definitions from the header file[1].
- Force sequential bus scanning. It seems parallel scanning is in fact
slower and causes more harm than good[1]. Adjust a comment to reflect that.
- Rename the __tcpi_(snd|rcv)_mss fields of the tcp_info structure to remove
the leading underscores since they are now implemented.
- Implement the tcpi_rto and tcpi_last_data_recv fields in the tcp_info
structure.
Use the EVENTHANDLER system to hook into the usb device configuration and
perform a function such as ejecting a 3G autoinstaller disk. The eventhandler
system properly tracks threads and is safe to unload, remove the
setting/clearing of a function pointer in the kernel by u3g(4) which included a
tsleep for safety.
Add a quirk for the Curitel UM175 where setting multiplexing for call
management over the data endpoint causes communication to die.
Take this one step further and model it on the existing NetBSD quirk and import
other device IDs from them.
Obtained from: NetBSD
Fix hardware issue with FTDI chips: avoid sending a zero length packet due to
hardware sending garbage on ZLPs.
Reported by: Corey Smith
Submitted by: HPS
r199563:
Fix copy & paste error and remove extra space before colon.
r199608:
Remove unnecessary structure packing.
r199609:
Add initial endianness support. It seems the controller supports
both big-endian and little-endian format in descriptors for Rx path
but I couldn't find equivalent feature in Tx path. So just stick to
little-endian for now.
r199610:
Because we know received bytes including CRC there is no reason to
call m_adj(9). The controller also seems to have a capability to
strip CRC bytes but I failed to activate this feature except for
loopback traffic.
r199611:
Add IPv4/TCP/UDP Tx checksum offloading support. It seems the
controller also has support for IP/TCP checksum offloading for Rx
path. But I failed to find to way to enable Rx MAC to compute the
checksum of received frames.
r199612:
Add __FBSDID.
r199613:
Only Tx checksum offloading is supported now. Remove experimental
code sneaked in r199611.
r199558:
Use bus_{read,write}_4 rather than bus_space_{read,write}_4.
r199561:
Use capability pointer to access PCIe registers rather than
directly access them at fixed address. Frequently the register
offset could be changed if additional PCI capabilities are added to
controller.
One odd thing is ET_PCIR_L0S_L1_LATENCY register. I think it's PCIe
link capabilities register but the location of the register does
not match with PCIe capability pointer + offset. I'm not sure it's
shadow register of PCIe link capabilities register.
