- Remove dead code. Calculated greatest common divisor was not used at all.
- Prefer u_int32_t over unsigned int to make its intention more clearer.
- Move the function to a header file and make it a static inline function.
Make OSS_GETVERSION ioctl really work. It has 'M' group, not 'P',
as different nearby ones, and was grabbed by MIXER_xxx() handler.
While there, replace '(cmd & MIXER_xxx(0)) == MIXER_xxx(0)' expressions
with more correct '(cmd & ~0xff) == MIXER_xxx(0)'. Use of bit operations
to compare numeric fields doesn't looks sane.
201408,201325,200089,198822,197373,197372,197214,196162). Since one of those
changes was a semicolon cleanup from somebody else, this touches a lot more.
- Improve tracer, to handle more cases of input-to-output monitoring
loopback.
- Use "igain" mixer control for input-to-output monitoring loopback.
- Allow AD1981HD codecs to use playback mixer. Now driver should be able to
really use it.
- Fix bug in shared muters operation.
(S)LIST_HEAD_INITIALIZER takes a (S)LIST_HEAD as an argument.
Fix some wrong usages.
Note: this does not affect generated binaries as this argument is not used.
PR: 137213
Submitted by: Eygene Ryabinkin (initial version)
Add multichannel (4.0, 5.1 and 7.1) playback support.
Stereo stream is no more duplicated to all ports. If you loose sound, check
you are using right connectors. Front speakers connector is usually green,
center/LFE - orange, rear - black, side - gray.
Make default recording source choosing more intelligent.
Change default recording level from 0 to 75.
It should increase chances for things to work just out of the box.
Improve support for High-speed USB audio devices.
- fix issues regarding the mixer, where the interface number was not set in
time.
- fix wrong use of resolution parameter.
Submitted by: Hans Petter Selasky
- Add some bits of HDMI/DisplayPort support from later specification updates.
It may be not enough to make them work, but at least should give some
information about these beasts.
- Add Realtek ALC887 codec ID.
- According to Linux, the ALi M5451 can do 31-bit DMA instead of just
30-bit like the reset of the controllers supported by this driver.
Actually ALi M5451 can be setup up to generate 32-bit addresses by
setting the 31st bit via the accompanying ISA bridge, which allows
it to work in sparc64 machines whose IOMMU require at least 32-bit
DMA. Even though other architectures would also benefit from 32-bit
DMA, enabling this bit is limited to sparc64 as bus_dma(9) doesn't
generally guarantee that a low address of BUS_SPACE_MAXADDR_32BIT
results in a buffer in the 32-bit range.
- According to Tatsuo YOKOGAWA's ali(4), the the DMA transfer size of
ALi M5451 is fixed to 64k and in fact using the default size of 4k
causes the chip to overrun the mapping, triggering uncorrectable
DMA errors on sparc64.
- The 4DWAVE DX and NX require the recording buffer to be 8-byte
aligned so adjust the bus_dma_tag_create(9) accordingly.
- Unlike the rest of the controllers supported by this driver, the
ALi M5451 only has 32 hardware channels instead of 64 so limit the
loop in tr_intr() accordingly. [1]
Submitted by: yongari [1]
Reviewed by: yongari (superset of what is committed)
Approved by: re (kib)
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
This dramatically pushing 99.9% interpolations and quantizations
error _below_ -180dB on 32bit dynamic range, resulting extremely
high quality conversion.
- Use BSPLINE interpolator for filter oversampling factor greater or
equal than 64 (log2 6).
Approved by: re (kib)
This cause dramatic effect in overall precision and conversion quality
by pushing down most aliasing artifacts around -180 dB.
Spectrogram analysis/comparison:
http://people.freebsd.org/~ariff/z_comparison/z_28vs30/
- Guard against possible 64bit overflow during accumulation process by
slightly normalize and saturate sample and coefficient multiplication,
possible during extreme 32bit downsampling (eg. 380KHz -> 8KHz) with
custom preset that require more than ~7000 taps filter (which is
overkill).
- Add knobs through FEEDER_RATE_PRESETS to set dynamic range of filter
coefficients/accumulator and prefered polynomial interpolator:
COEFFICIENT_BIT:X
(where 1 <= X <= 30, default: 30)
ACCUMULATOR_BIT:X
(where 32 <= X <=64, default: 58)
INTERPOLATOR:I
(where I = ZOH, LINEAR, QUADRATIC, HERMITE, BSPLINE,
OPT32X, OPT16X, OPT8X, OPT4X, OPT2X)
Approved by: re (kib)
Note that this does not actually enable full-range i/o requests for
64 architectures, and is done now to update KBI only.
Tested by: pho
Reviewed by: jhb, bde (as part of the review of the bigger patch)
- honor parent DMA tag limitations, as man page requires,
- allow data buffer to be allocated within full 64bit address range, when
support is announced by hardware,
- add quirk, disabling 64bit addresses for broken chips, use it for MCP78.
FEEDER_RATE_PRESET "OVERSAMPLING_FACTOR:X .. .." where
X = log2(oversampling factor).
- Lower down default filter oversampling factor from 128
(log2 = 7) to 32 (log2 = 5), saving worth of 80 Kb.
The use of better polynomial interpolator will raise
its conversion quality/accuracy to match (or slightly
better) with previous settings.
- Bump driver version.
coefficients quality:
- Linear interpolator for oversampling factor larger and equal
than 4096 (log2 = 12).
- Quadratic interpolator for oversampling factor larger and equal
than 256 (log2 = 8).
Default oversampling factor (128 ~ log2 = 7) will use OPT32X, which
provides better accuracy.
