When the mps(4) and mpr(4) drivers need to reinitialize the
firmware, they sometimes need to reallocate all of the memory
allocated by the driver. The reallocation happens whenever the IOC
Facts change. That should only happen after a firmware upgrade.
If the reinitialization happens as a result of a timed out command
sent to the card, the command that timed out and triggered the
reinit may have been freed if iocfacts_allocate() reallocated all
memory. If the caller attempts to access the command after that,
the kernel will panic because the caller will be dereferencing
freed memory.
The solution is to set a flag in the softc when we reallocate,
and avoid dereferencing the command strucure if we've reallocated.
The changes are largely the same in both drivers, since mpr(4) is a
derivative of mps(4).
o In iocfacts_allocate(), if the IOC Facts have changed and we
need to reallocate, set the REALLOCATED flag in the softc.
o Change wait_command() to take a struct mps_command ** instead of
a struct mps_command *. This allows us to NULL out the caller's
command pointer if we have to reinit the controller and the data
structures get reallocated. (The REALLOCATED flag will be set
in the softc if that has happened.)
o In every place that calls wait_command(), make sure we handle
the case where the command is NULL after the call.
o The mpr(4) driver has mpr_request_polled() which can also
reinitialize the card. Also check for reallocation there.
Reviewed by: scottl, slm
MFC after: 1 week
Sponsored by: Spectra Logic
Do the allocation before requesting the IOCFacts message. This triggers
the LSI firmware to recognize the multiqueue should be enabled if available.
Multiqueue isn't used by the driver yet, but this also fixes a problem with
the cached IOCFacts not matching latter checks, leading to potential problems
with error recovery.
As a side-effect, fetch the driver tunables as early as possible.
Reviewed by: slm
Obtained from: Netflix
Differential Revision: D9243
This includes NVMe device support and adds support for the following adapters:
SAS 3408
SAS 3416
SAS 3508
SAS 3516
SAS 3616
SAS 3708
SAS 3716
Reviewed by: ken, scottl, asomers, mav
Approved by: ken, scottl, mav
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D10095
This is mostly a version bump to stay in version number sync with firmware.
The only change there was cosmetic: Display degraded speed message upon
receiving Active Cable Exception Event with DEGRADED reason code.
Discussed with: slm@
MFC after: 1 week
All of the printing from the tables file now has wrappers so that the
handling is cleaner and it's possible to print something out (say, during
development) without having to fight the global debug flags. This re-org
will also make it easier to have the tables be compiled out at build time
if desired.
Other than fixing some minor bugs, there are no user-visible changes from
this change
Sponsored by: Netflix, Inc.
Differential Revision: D9238
that are apparently misconfigured by the manufacturer and cause the mapping
logic to fail. The fallback allows drive numbers to be assigned based on the
PHY number that they're attached to. Add sysctls and tunables to overrid
this new behavior, but they should be considered only necessary for debugging.
Reviewed by: imp, smh
Obtained from: Netflix
MFC after: 3 days
Sponsored by: D8403
- Updated all files with 2015 Avago copyright, and updated LSI's copyright
dates.
- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).
- Added a sysctl variable to control how StartStopUnit behavior works. User can
select to spin down disks based on if disk is SSD or HDD.
- Inquiry data is required to tell if a disk will support SSU at shutdown or
not. Due to the addition of mpssas_async, which gets Advanced Info but not
Inquiry data, the setting of supports_SSU was moved to the
mpssas_scsiio_complete function, which snoops for any Inquiry commands. And,
since disks are shutdown as a target and not a LUN, this process was
simplified by basing it on targets and not LUNs.
- Added a sysctl variable that sets the amount of time to retry after sending a
failed SATA ID command. This helps with some bad disks and large disks that
require a lot of time to spin up. Part of this change was to add a callout to
handle timeouts with the SATA ID command. The callout function is called
mpssas_ata_id_timeout(). (Fixes PR 191348)
- Changed the way resets work by allowing I/O to continue to devices that are
not currently under a reset condition. This uses devq's instead of simq's and
makes use of the MPSSAS_TARGET_INRESET flag. This change also adds a function
called mpssas_prepare_tm().
- Some changes were made to reduce code duplication when getting a SAS address
for a SATA disk.
- Fixed some formatting and whitespace.
- Bump version of mps driver to 9.255.01.00-fbsd
PR: 191348
Reviewed by: ken, scottl
Approved by: ken, scottl
MFC after: 1 week
message synced to the changes in r283632, those changes are now backed out.
Another commit will be done that is exactly the same as r283632 except it will
have to correct commit message.
Approved by: ken, scottl, asomers, gibbs
This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.
Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.
o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.
o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.
Thanks to LSI for developing and testing this driver for FreeBSD.
share/man/man4/mpr.4:
mpr(4) man page.
sys/dev/mpr/*:
mpr(4) driver files.
sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.
sys/conf/files:
Add the mpr(4) driver.
sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.
sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.
sys/i386/conf/XEN:
Exclude the mpr module from building here.
Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added
