The current mapping of driver counters to netstat counters is wrong.
For example, a single jabber packet, will cause the Ierrs counter to
count three times.
The work for mapping the hardware and software counters to their right
place in netstat counters were already done in Linux, take that as is
to the FreeBSD driver.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
To be used by the mlx5 callbacks exposed to the mlxfw module.
Linux commit:
d2ad488b0073bd1a2c3f5d2ea50a7eb632103e5d
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Enhance MCAM to allow the driver to query which access regs are
supported. For now, expose the regs needed for FW flashing.
Linux commit:
0ab87743cc8c5bcd482daf71961ed5fc45349e01
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
MCC (Management Component Control) allows to control a firmware
component update.
MCDA (Management Component Data Access) allows to read and write
a firmware component.
MCQI (Management Component Query Information) allows to query
information about firmware components.
Linux commit:
4717628938423fcba0aa8fa889e9fed4eb6a655f
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
On load_one, we now cache our capabilities registers internally, similar
to QUERY_HCA_CAP. Capabilities can later be queried using macros
introduced in this patch.
Linux commit:
71862561f3a62015a11de16d1c306481e8415c08
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Introduced registers will expose capabilities of new registers and
features related to port/management.
Driver will query MCAM and PCAM in order to avoid failing on old
firmwares with lack of support.
Linux commit:
c835ad64683bd3e2d1b31ed2cb1ff4366932edb1
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
PCAM: Ports capabilities mask register.
MCAM: Management capabilities mask register.
PCAM and MCAM registers will provide information regarding firmware
support for different features, in order to avoid cases where new driver
combined with old firmware results in syndromes (for ex. PCIe counters
before this patchset).
Linux commit:
cfdcbceaeffc669b70d904d80a2df9c86c232566
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Today mlx5 devices support two teardown modes:
1- Regular teardown
2- Force teardown
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been
scattered to memory
Linux commit:
fcd29ad17c6ff885dfae58f557e9323941e63ba2
MFC after: 3 days
Sponsored by: Mellanox Technologies
Else the SQs won't be properly released when closing rate-limited connections
leading to wrong state transitions on the SQ.
MFC after: 3 days
Sponsored by: Mellanox Technologies
When using CQE zipping, one can choose between RX hash and Checksum.
This will indicate the parameter on which a zipping session should be
stopped.
While porting the Linux code, Checksum was chosen. However, the value
of Checksum is not being used anywhere.
For the FreeBSD driver, we prefer to use the RX hash format which will
guarantee the RX hash value for all the mini CQEs.
While at it, make sure to initialize the Checksum value in the
decompressed CQE.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
After doing performance measurements, it seems like CQE zipping doesn't
have any significant benefit.
Moreover, we know that this feature is disabled by default on other
operating systems (Linux for example).
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Split the function into the mlx5e_update_stats_locked() core and make
mlx5e_update_stats_work() call the _locked helper, similar to many other
places in the kernel. This improves the code structure, making the
locking clean.
Submitted by: kib@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Instead of waiting for all jobs to be cancelled, simply close the completion
queue to prevent more completion events and let mlx5e_destroy_rq() cleanup
the remaining mbufs.
MFC after: 3 days
Sponsored by: Mellanox Technologies
The number of priorities is always 8, while the number of traffic classes
supported can vary. While at it convert the sysctl node into an array.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Instead of reading Ethernet RFC 2819 pXtoYoctets counters from
hardware which counts RX octets, count tx_stat_pXtoYoctets from
Ethernet extended counters which counts TX octets.
TX jumbo counters should be accumulated only after the PPCNT
counters were fetched from hardware with their latest value.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Avoid an infinite software firmware reset loop that may be caused by a
hardware bug by limiting the maximum number of resets.
The counter between resets is reset by request for reset, and not by a
successful reset.
The interval between two resets can be configured via sysctl:
hw.mlx5.sw_reset_timeout
which is global to all mlx5 devices in the system.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Make sure the interrupt handlers don't race with the fast unload one
code in the shutdown handler.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Temperature warning event is sent by FW to indicate high temperature
as detected by one of the sensors on the board.
Add handling of this event by writing the numbers of the alert sensors
to the kernel log.
Linux commit:
1865ea9adbfaf341c5cd5d8f7d384f19948b2fe9
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
While at it remove unused interface state bits. This also fixes and issue
during shutdown:
There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.
The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.
Linux commit:
10a8d00707082955b177164d4b4e758ffcbd4017
b3cb5388499c5e219324bfe7da2e46cbad82bfcf
MFC after: 3 days
Sponsored by: Mellanox Technologies
Add support for DIM based on Linux,
with some minor adaptions specific to FreeBSD.
Linux commit
f97c3dc3c0e8d23a5c4357d182afeef4c67f5c33
MFC after: 3 days
Sponsored by: Mellanox Technologies
Checksum offloading for SCTP is not currently specified for virtio.
If the hypervisor announces checksum offloading support, it means TCP
and UDP checksum offload. If an SCTP packet is sent and the host announced
checksum offload support, the hypervisor inserts the IP checksum (16-bit)
at the correct offset, but this is not the right checksum, which is a CRC32c.
This results in all outgoing packets having the wrong checksum and therefore
breaking SCTP based communications.
This patch removes SCTP checksum offloading support from the virtio
network interface.
Thanks to Felix Weinrank for making me aware of the issue.
Reviewed by: bryanv@
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D20147
times - on every interrupt by using an own set of device methods for the
IGB class. This translates to introducing igb_if_intr_{disable,enable}()
and igb_if_{rx,tx}_queue_intr_enable() with that IGB-specific code moved
out of their EM counterparts and otherwise continuing to use the EM IFDI
methods also for IGB.
Note that igb_if_intr_{disable,enable}() also issue E1000_WRITE_FLUSH as
lost with the conversion of igb(4) to iflib(4).
Also note, that the em_if_{disable,enable}_intr() methods are renamed to
em_if_intr_{disable,enable}() for consistency with the names used in the
interface declaration.
o In em_intr():
- Don't bother to bail out if the interrupt type is "legacy", i. e. INTx
or MSI, as iflib(4) doesn't use ift_legacy_intr methods for MSI-X. All
other iflib(4)-based drivers avoid this check, too.
- Given that only the MSI-X interrupts have one-shot behavior (by taking
advantage of the EIAC register), explicitly disable interrupts. Hence,
em_intr() now matches what {em,igb}_irq_fast() previously did (in case
of igb(4) supposedly also to work around MSI message reordering errata
on certain systems).
o In em_if_intr_disable():
- Clear the EIAC register unconditionally for 82574 and not just in case
of MSI-X, matching em_if_intr_enable() and bringing back the last hunk
of r206437 lost with the iflib(4) conversion.
- Write to EM_EIAC for clearing said register instead of to the IGB-only
E1000_EIAC used ever since the iflib(4) conversion.
Reviewed by: shurd
Differential Revision: https://reviews.freebsd.org/D20176
Allow users to specify multiple dump configurations in a prioritized list.
This enables fallback to secondary device(s) if primary dump fails. E.g.,
one might configure a preference for netdump, but fallback to disk dump as a
second choice if netdump is unavailable.
This change does not list-ify netdump configuration, which is tracked
separately from ordinary disk dumps internally; only one netdump
configuration can be made at a time, for now. It also does not implement
IPv6 netdump.
savecore(8) is already capable of scanning and iterating multiple devices
from /etc/fstab or passed on the command line.
This change doesn't update the rc or loader variables 'dumpdev' in any way;
it can still be set to configure a single dump device, and rc.d/savecore
still uses it as a single device. Only dumpon(8) is updated to be able to
configure the more complicated configurations for now.
As part of revving the ABI, unify netdump and disk dump configuration ioctl
/ structure, and leave room for ipv6 netdump as a future possibility.
Backwards-compatibility ioctls are added to smooth ABI transition,
especially for developers who may not keep kernel and userspace perfectly
synced.
Reviewed by: markj, scottl (earlier version)
Relnotes: maybe
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D19996
Right now ath_rate_sample has a fixed rate schedule, rather than the minstrel_ht
style "best, good, most reliable" triplet. So, if higher rates are tried then
it'll not fail back to a lower MCS rate in that transmission schedule.
This means that in low SNR situations it'll not easily drop to MCS0 unless enough
transmissions occur to allow rate control to eventually decide to drop; and if
it's TCP traffic it'll get slowed down because of packet loss.
It's worse for 2-stream and 3-stream rates; it doesn't ever fall back to lower
stream rates, and these higher stream rates required higher SNR to work.
So instead let's (for now?) have each of the 11n transmit rates use MCS0 as
the last attempt. ath_rate_sample will quickly see that rate succeeds more
and will move to it much quicker.
Testing:
* AR9344 (Wasp) - 2G STA mode
These are some fun issues I've found with my upstairs wifi link at such a ridiculous
low signal level (like, < 5dB.)
* Add per-station tx/rx rssi statistics, in potential preparation to use that
in the RX rate control.
* Call the rate control on each received frame to let it potentially use
it as a hint for what rates to potentially use. It's a no-op right now.
* Do ANI calibration during scan as well. The ath_newstate() call was disabling the
ANI timer and only re-enabling it during transitions to _RUN. This has the
unfortunate side-effect that if ANI deafened the NIC because of interference
and it disassociated, it wouldn't be reset and the scan would never hear beacons.
The ANI configuration is stored at least globally on some HALs and per-channel
on others. Because of this a NIC reset wouldn't help; the ANI parameters would
simply be programmed back in.
Now, I have a feeling I also need to do this during AUTH/ASSOC too and maybe,
if I'm feeling clever, I need to reset the ANI parameters on a given channel
during a transition through INIT or if the VAP is destroyed/re-created.
However for now this gets me out of the immediate weeds with connectivity
upstairs (and thus I /can/ commit); I'll keep chipping away at tidying this
stuff up in subsequent commits.
Tested:
* AR9344 (Wasp), 2G STA mode
so it does not require a bounce buffer. The only need for this was
to align the buffer address. Implement unaligned access and we don't
need to copy data twice.
o Remove contigmalloc-based bounce buffer from xDMA code since it is
not suitable for arbitrary memory provided by platform, which is
sometimes a dedicated piece of memory that is not managed by OS at all.
Sponsored by: DARPA, AFRL
It cannot load it automatically at boot, because the root filesystem
is not there yet. An alternative would be adding ispfw(4) to GENERIC,
but it's an additional 1MB.
Reviewed by: mav
MFC after: 2 weeks
Sponsored by: Klara Inc.
Differential Revision: https://reviews.freebsd.org/D19369
Drivers can now pass up numa domain information via the
mbuf numa domain field. This information is then used
by TCP syncache_socket() to associate that information
with the inpcb. The domain information is then fed back
into transmitted mbufs in ip{6}_output(). This mechanism
is nearly identical to what is done to track RSS hash values
in the inp_flowid.
Follow on changes will use this information for lacp egress
port selection, binding TCP pacers to the appropriate NUMA
domain, etc.
Reviewed by: markj, kib, slavash, bz, scottl, jtl, tuexen
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20028
From 7d8dc6544c
"The mcbin (and likely others) have a nonstandard uart clock. This means
that the earlycon programming will incorrectly set the baud rate if it is
specified. The way around this is to tell the kernel to continue using the
preprogrammed baud rate. This is done by setting the baud to 0."
Our drivers (uart_dev_ns8250) do respect zero, but SPCR would error. Let's
not error.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: mw, imp, bcran
Differential Revision: https://reviews.freebsd.org/D19914
This is fairly similar to the AES-GCM support in ccr(4) in that it will
fall back to software for certain cases (requests with only AAD and
requests that are too large).
Tested by: cryptocheck, cryptotest.py
MFC after: 1 month
Sponsored by: Chelsio Communications
