Add support for different request block format used by Gen-IIe Marvell SATA.
This adds support for Marvell 6042/7042 chips and Adaptec 1430SA controller.
MFC r198718:
Allow newly added controllers to use full I/O sizes.
- Revert r191568 partially. Forcing AHCI mode by changing device subclass
and progif is evil. It doesn't work reliably[1] and we should honor BIOS
configuration by the user.
- If the SATA controller is enbled but combined mode is disabled, mask off
the emulated IDE channel on the legacy IDE controller.
Pointed out by: mav[1]
Most of the pieces came from Marius- correct settings for channels
and resource management. The one piece missing was that you cannot
for SBus cards replace 32 bit operations with A64 operations- not
supported. This is an MFC of r198822.
It seems some 82559ER controllers do not support Rx checksum
offloading. Datasheet said nothing about the limitation of 82559ER
except WOL. Explicitly disable Rx checksum offloading for
controllers that is known to lack the capability.
PR: kern/138135
Tested by: Gooderum, Mark < mgooderum <> websense dot com >
When the timeout backoff hits the maximum value, leave it capped at the
maximum value rather than setting it to the result of a boolean expression
that is always true.
Increase AAC_CMD_TIMEOUT from 30s to 120s to help avoid spurious
"COMMAND 0x........ TIMEOUT AFTER .. SECONDS" messages. Any commands
that get truly stuck will still trigger the warning and the hardware
health check, just a little bit later.
Cleanup in r600_blit
- Don't bother to assign vb until we know we have enough space
- Add variables for sx2, sy2, dx2, dy2 so that these aren't
calculated over and over, also reduce chance of errors.
- Use switch to assign color/format
SVN r197174:
Make sure we never place the cursor outside the screen.
For some vague reason, it may be possible that scp->cursor_pos exceeds
scp->ysize * scp->xsize. This means that teken_set_cursor() may get
called with an invalid position. Just ignore the old cursor position in
this case.
Reported by: Paul B. Mahol <onemda gmail com>
SVN r198213:
Make lock devices work properly.
It turned out I did add the code to use the init state devices to set
the termios structure when opening the device, but it seems I totally
forgot to add the bits required to force the actual locking of flags
through the lock state devices.
Reported by: ru
SVN r198215, r198217:
Fix a typo in the jail(8) manpage.
Submitted by: Jille Timmermans <jille quis cx>
SVN r198216:
Fix qouting in a comment, to make it look more consistent
Submitted by: Jille Timmermans <jille quis cx>
SVN r198223:
Properly set the low watermarks when reducing the baud rate.
Now that buffers are deallocated lazily, we should not use
tty*q_getsize() to obtain the buffer size to calculate the low
watermarks. Doing this may cause the watermark to be placed outside the
typical buffer size.
This caused some regressions after my previous commit to the TTY code,
which allows pseudo-devices to resize the buffers as well.
Reported by: yongari, dougb
Workaround buggy BIOS code in USB regard. By doing the BIOS to OS handover for
all host controllers at the same time, we avoid problems where the BIOS will
actually write to the USB registers of all the USB host controllers every time
we handover one of them, and consequently reset the OS programmed values.
Fix the 106/109 USB Japanese keyboard "underscore" issue.
Sun Type 6 USB keyboard support added in rev 1.46 conflicted with
some scan codes used in Japanese keyboards because the scan code
conversion routine was ambiguous for the overlapped codes.
PR: ports/134005
Add extra safety locking when clobbering xfer->flags_int.started in start and
stop functions, because xfer->flags_int is also updated by the USB controller,
under the controller lock.
Import two PCI quirks from Linux
- Add quirk for ATI SB600 and SB700 to free SMB controller
- Correct schedule sleep time to 10us on the VIA ehci controller
