commands during controller initialization.
DELAY() does not work here during config_intrhook context - we need to
explicitly relinquish the CPU for the admin command completion to
get processed.
Sponsored by: Intel
Reported by: Adam Brooks <adam.j.brooks@intel.com>
Reviewed by: carl
MFC after: 3 days
and firmware revision in the controller's identify structure.
Also modify consumers of these fields to ensure they only use the
specified number of bytes for their respective fields.
Sponsored by: Intel
Reviewed by: carl
MFC after: 3 days
The read DMA request logic operation is based on having sufficient
available space in the transmit data buffer (TXMBUF) before a read
DMA can be requested. There are four read DMA channels that use
the TXMBUF, and the logic checks if the available free space in the
TXMBUF is large enough for all the data in the four Send Buffers
for which buffer descriptors have been fetched. The Enable_Request
signal is asserted only if the free TXMBUF space is larger than the
sum of the four DMA length registers. The power-up default value
of BGE_RDMA_LSO_CRPTEN_CTRL register bit 25 (bit 21 on BCM5720) is
zero, which selects the DMA length registers to connect to the
input of the adder block. The DMA length registers are
asynchronously reset following BCM5719/BCM5720 power-up, and due to
the lack of synchronous deassertion of the length registers reset
signal these resisters may contain uninitialized values following
the reset deassertion.
In the case of the failure the uninitialized DMA length register
values added up to more than the TXMBUF size, which prevented the
assertion of the Enable_Request signal and any subsequent read DMA
to start. This lockup condition is the root cause of failing to
generate any transmit traffic.
To workaround the issue, select alternate output of multiplexers
and transmit the first four Ethernet frames. This overwrites the
DMA length registers with valid values.
Reported by: Geans Pin <geanspin@broadcom.com>
Reviewed by: Geans Pin <geanspin@broadcom.com>
constraint to 8. Previously it may have triggered watchdog
timeouts.
o Check whether interrupt is ours or not.
o Enable interrupts before attemping to transmit queued packets.
This will slightly improve TX performance.
o No need to clear IFF_DRV_OACTIVE in a loop. AE_FLAG_TXAVAIL is
used to know whether there are enough available TxD ring space.
o Added missing bus_dmamap_sync(9) in ae_rx_intr() and rearranged
code to avoid unncessary register access.
o Make sure to clear TxD, TxS, RxD rings in driver initialization.
Otherwise some data in these rings could be interpreted as
'updated' which in turn will advance internally maintained
pointers and can trigger watchdog timeouts.
PR: kern/180382
settings for ACPI-enumerated serial ports by forcing any IRQs that use
an ISA IRQ value with these settings to active-high instead of active-low.
This is known to occur with the BIOS on an Intel D2500CCE motherboard.
Tested by: Robert Ames <robertames@hotmail.com>, lev
Submitted by: Juergen Weiss weiss at uni-mainz.de (original patch)
We need to fix wpa_supplicant because it checks whether the card has
ic_cryptocaps set. Since net80211 can do software encryption this check in
wpa_supplicant is wrong.
"Gamers Keyboards" by adding a tunable, "hw.usb.ukbd.pollrate", which
can fix the polling rate of the attached USB keyboards in the range
1..1000Hz. A similar feature already exists in the USB mouse
driver. Use with care! Might leave you without keyboard input. This
feature is only available when the USB_DEBUG option is set in the
kernel configuration file.
Correct "unit" type to "int" while at it.
a mailbox command and which registers to copy back in when
the command completes, the bits being set need to not only
specify what bits you want to add from the default from the
table but also what bits you want *subtract* (mask) from the
default from the table.
A failing ISP2200 command pointed this out.
Much appreciation to: marius, who persisted and narrowed down what
the failure delta was, and shamed me into actually fixing it.
MFC after: 1 week
ixgbe driver. As it was, when building them as a module INET
and INET6 are not defined. In these drivers it does not cause
a panic, however it does result in different behavior in the
ioctl routine when you are using a module vs static, and I
think the behavior should be the same.
MFC after: 3 days
MFprojects/camlock r248982:
Stop abusing xpt_periph in random plases that really have no periph related
to CCB, for example, bus scanning. NULL value is fine in such cases and it
is correctly logged in debug messages as "noperiph". If at some point we
need some real XPT periphs (alike to pmpX now), quite likely they will be
per-bus, and not a single global instance as xpt_periph now.
when building the driver as a module the result of the present
system results in INET and INET6 being undefined, and will cause
the panic in ixgbe_tso_setup(). The Makefile in the module directory
now renders the conditional in the source unnecessary and wrong.
MFC after: ASAP - the panic as a module must not get into 9.2
processing. Thanks for John Baldwin for catching this. Not
clearing the flag member of the rxbuf could result in a NULL
mbuf pointer being used.
MFC after: 2 days (this needs to get into 9.2!)
H/W not de-asserting the interrupt at all. On x86, and because of the
following conditions, this results in a hard hang with interrupts disabled:
1. The uart(4) driver uses a spin lock to protect against concurrent
access to the H/W. Spin locks disable and restore interrupts.
2. Restoring the interrupt on x86 always writes the flags register. Even
if we're restoring the interrupt from disabled to disabled.
3. The x86 CPU has a short window in which interrupts are enabled when the
flags register is written.
4. The uart(4) driver registers a fast interrupt by default.
To catch this case, we first try to clear any pending H/W interrupts and in
particular, before setting up the interrupt. This makes sure the interrupt
is masked on the PIC. The interrupt handler now has a limit set on the
number of iterations it'll go through to clear interrupt conditions. If the
limit is hit, the handler will return FILTER_SCHEDULE_THREAD. The attach
function will check for this return code and avoid setting up the interrupt
and foce polling in that case.
Obtained from: Juniper Networks, Inc.
structure copying in random_ident_hardware(). This change will also help
further modularization of random(4) subsystem.
Submitted by: arthurmesh@gmail.com
Reviewed by: obrien
Obtained from: Juniper Networks
VMware up to at least ESXi 5.1. Actually, using INTx in that case instead
may still result in interrupt storms, with MSI being the only working
option in some configurations. So introduce a PCI_QUIRK_DISABLE_MSIX quirk
which only blacklists MSI-X but not also MSI and use it for the VMware
PCI-PCI-bridges. Note that, currently, we still assume that if MSI doesn't
work, MSI-X won't work either - but that's part of the internal logic and
not guaranteed as part of the API contract. While at it, add and employ
a pci_has_quirk() helper.
Reported and tested by: Paul Bucher
- Use NULL instead of 0 for pointers.
Submitted by: jhb (mostly)
Approved by: jhb
MFC after: 3 days
of Skyhawk adapters.
Many thanks to Emulex for their continued support of FreeBSD.
Submitted by: "Duvvuru,Venkat Kumar" <VenkatKumar.Duvvuru Emulex.Com>
MFC after: 1 day
full issue with ARC-1214 and ARC-1224.
Many thanks to Areca for continuing to support FreeBSD.
Submitted by: 黃清隆 <ching2048 areca com tw>
MFC after: 1 day
user, where when more than one hpt27xx adapters are being used,
the "unit number" stays at 0.
Many thanks to HighPoint for providing this driver update.
MFC after: 1 day
controllers. Update the hptiop(4) manual page to reflect this
as well as mentioning that some cards are already end-of-life.
Many thanks to Highpoint for providing this driver update.
MFC after: 1 day
/dev/kmem and /dev/mem (in addition to traditional file permission checks).
PRIV_KMEM_READ is different from other PRIV_* checks in that it's allowed
by default.
Reviewed by: kib, mckusick
when the interface is up.
- Add a tunable to control the TOE's rx coalesce feature (enabled by
default as it always has been). Consider the interface MTU or the
coalesce size when deciding which cluster zone to use to fill the
offload rx queue's free list. The tunable is:
dev.{t4nex,t5nex}.<N>.toe.rx_coalesce
MFC after: 1 day
* Add 802.11n 2ghz and 5ghz tables, including legacy rates and up to
MCS23 rates (3x3.)
* Populate the rate code -> rate index lookup table with MCS _and_
normal rates, but _not_ the basic rate flag. Since the basic rate flag
is the same as the MCS flag, we can only use one.
* Introduce some accessor inlines that do PLCP and rate table lookup/access
and enforce that it doesn't set the basic rate bit. They're not
designed for MCS rates, so it will panic.
* Start converting drivers that use the rate table stuff to use the
accessor inlines and strip the basic flag.
* Teach AMRR about basic 11n - it's still as crap for MCS as it is
being used by iwn, so it's not a step _backwardS_.
* Convert iwn over to accept 11n MCS rates rather than 'translate' legacy
to MCS rates. It doesn't use a lookup table any longer; instead it's a
function which takes the current node (for HT parameters) and the
rate code, and returns the hardware PLCP code to use.
Tested:
* ath - it's a no-op, and it works that way
* iwn - both 11n and non-11n
It's not enabled by default in net80211 so this is a no-op unless
if you enable it (ifconfig wlan0 powersave).
Tested:
* iwn0: <Intel WiFi Link 5100> mem 0xf4300000-0xf4301fff irq 17 at device 0.0 on pci3
TODO:
* .. test on all the other NICs
* See if I have to disable it during scan and such
* Make it configurable live, rather than only after it's done its initial
receive calibration.
