The iwn(4) firmware forgets most of its channel state after an RXON
command. This means that any beacons its seen on passive 5GHz channels
are forgotten upon an association/authorisation request.
This unfortuantely means that 5GHz association almost always fails -
the assoc and/or auth frames are dropped with a status of "passive
channel, haven't seen a beacon yet." (0x90.)
So:
* add an xmit queue, global, to buffer frames
* modify the xmit path to use the mbuf tag from net80211
to specify raw frame details
* buffer xmit frames from both raw and non-raw paths
* if a beacon is seen in the RX path, schedule a taskqueue to
send said frames and un-buffer things.
* flush frames during state change back to INIT, or NIC
down/up/detach.
This isn't the final shape I'd like this to be in but it certainly
is better than 5GHz "not working at all".
Tested:
* Intel 5100, STA mode (before spilling coffee)
* Intel 5300, STA mode (after spilling coffee)
Story:
* This has been bugging me at work for months, which I just
worked around by throwing an ath(4) into my Lenovo T400 cardbus
slot.
* Our ops director discovered indeed FreeBSD runs well on the
Lenovo T420p, except for that pesky 5GHz thing. So now developers
also can have a T420p running FreeBSD to do work with.
Their #1 feedback to me - "boy it'd be nice if 5GHz wifi worked."
* .. then, I was at NANOG but stuck with 5GHz only wifi and no ath(4)
NIC to put in a laptop - and I snapped.
Thus, the reason this is actually work related.
MFC after: 2 weeks
Sponsored by: Norse Corp, Inc.
There was a inconsistency which led to enable passthrough commands
being interpreted as actual touchpad commands.
Submitted by: Jan Kokemüller <jan.kokemueller at gmail.com>
MFC after: 1 week
ct_rxid value on CTIO completion. Try to workaround that using tag_id
from the CCB, pointed by still valid ct_syshandle.
I don't know whether this is valid fix or dirty hack, but considering that
alternative is indefinitely stuck command -- it worth trying.
MFC after: 1 week
In bxe_set_mc_list(): added missing BXE_MCAST_UNLOCK()
In __ecore_vlan_mac_h_exec_pending(): need to check for ECORE_PENDING
Submitted by:gary.zambrano@qlogic.com
o rev. 1.10: Nuke trailing whitespace.
o rev. 1.15: Fix typo in comment.
o rev. 1.16: Add the following registers from IEEE 802.3-2009 Clause 22:
- PSE control register (0x0b)
- PSE status register (0x0c)
- MMD access control register (0x0d)
- MMD access address data register (0x0e)
o rev. 1.17 (comments only): The bit location of link ability is different
between 1000Base-X and others (see Annex 28B.2 and 28D).
o rev. 1.18: Nuke dupe word.
Obtained from: NetBSD
MFC after: 1 week
Sponsored by: genua mbh
This change re-organizes code a little bit to extract common pieces
of ttm_alloc_new_pages() and ttm_get_pages() into dedicated functions.
Also, for requests without address restrictions regular vm_page_alloc()
is used.
Lastly, when vm_page_alloc_contig() fails we call VM_WAIT before calling
vm_pageout_grow_cache() to ensure that there is enough free pages at all.
Reviewed by: kib
MFC after: 15 days
If the pathname is absolute or dirfd is AT_FDCWD we can
handle it exactly like open(2).
Otherwise we output an A record to indicate that the path of
an open directory needs to be used (earlier in the trace).
Differential Revision: D2810
Reviewed by: jhb
MFC after: a bit
vtnet interfaces are always in promiscuous mode (at least if the
VIRTIO_NET_F_CTRL_RX feature is not negotiated with the host). if_promisc() on
a vtnet interface returned ENOTSUP although it has IFF_PROMISC set. This
confused the bridge code. Instead we now accept all enable/disable promiscuous
commands (and always keep IFF_PROMISC set).
There are also two issues with the if_bridge error handling.
If if_promisc() fails it uses bridge_delete_member() to clean up. This tries to
disable promiscuous mode on the interface. That runs into an assert, because
promiscuous mode was never set in the first place. (That's the panic reported in
PR 200210.)
We can only unset promiscuous mode if the interface actually is promiscuous.
This goes against the reference counting done by if_promisc(), but only the
first/last if_promic() calls can actually fail, so this is safe.
A second issue is a double free of bif. It's already freed by
bridge_delete_member().
PR: 200210
Differential Revision: https://reviews.freebsd.org/D2804
Reviewed by: philip (mentor)
Add a check for NULL before strcmp on smbios information incase it is not populated
Differential Revision: https://reviews.freebsd.org/D2750
Reviewed by: ngie, jhb
Approved by: rpaulo
Sponsored by: ScaleEngine Inc.
bxe_ioctl() completes all functions within its context as opposed to a taskqueue earlier.
bxe_handle_rx_mode_tq() no longer required. bxe_set_rx_mode() handles the functionality within its context
Submitted by:gary.zambrano@qlogic.com
MFC after:5 days
which is default. It was broken in r281441.
It appears that set_trackpoint_parameters() call on resume disables the
mouse. So, we need not call it on resume if hw.psm.trackpoint_support=0.
The problem is that the probe functions are used both for probing and
for reiniting on resume. And the absense of the softc parameter is used
as a mark to distinguish reinit and probe, which is quite ugly. At the
same time the softc parameter is needed to call set_trackpoint_parameters().
o Change the arguments of probefunc_t to always supply the softc, and
use additional enum argument to tell probing from initing.
o Don't call set_trackpoint_parameters() from global doinitialize(),
instead call it from the enable_trackpoint() only.
o In enable_synaptics() call enable_trackpoint() in both probe and
reinit cases.
Together with: Jan Kokemüller <jan.kokemueller gmail.com>
Work based on Cavium Thunder PCIe driver by Semihalf.
Reviewed by: andrew, jhb
Sponsored by: HEIF5
Differential Revision: https://reviews.freebsd.org/D2386
PCI infrastructure instantiates a non-existent resource.
This has BARs suddenly show up with pciconf(8) under
VMware as well. Now that we read the BAR ourselves, ask
for the correct resource type.
The FreeBSD extension adds a new request type, called blkif_segment_block
which has a size of 112bytes for both i386 and amd64. This is fine on
amd64, since requests have a size of 112B there also. But this is not true
for i386, where requests have a size of 108B. So on i386 we basically
overrun the ring slot when queuing a request of type blkif_segment_block_t,
which is very bad.
Remove this extension (including a cleanup of the public blkif.h header
file) from blkfront and blkback.
Sponsored by: Citrix Systems R&D
Tested-by: cperciva
drivers, one for fdt, one for acpi. It then uses this to decide if it will
use fdt or acpi.
The GICv2 (interrupt controller) and Generic Timer drivers have been
updated to handle both cases.
As this is early code we still need FDT to find the kernel console, and
some parts are still missing, including PCI support.
Differential Revision: https://reviews.freebsd.org/D2463
Reviewed by: jhb, jkim, emaste
Obtained from: ABT Systems Ltd
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
Use the same scheme implemented to manage credentials.
Code needing to look at process's credentials (as opposed to thred's) is
provided with *_proc variants of relevant functions.
Places which possibly had to take the proc lock anyway still use the proc
pointer to access limits.
gracefully fail if the /dev/megaraid_sas_ioctl_node symlink already exists.
This can happen if mfi(4) and mrsas(4) are both attached to cards and
providing Linux emulation support. Let the first one win. An equivalent
change needs to be done to mrsas(4). Extra credit would be to pass the
Linux emulation call to the other driver when appropriate. This will
probably be a rare case and the user can manually change where the symlink
points to.
MFC after: 3 days
(easily) without having to go to other drivers to change the
magical return values. This wouldn't be so bad if there were
proper defines for these constants.
In particular dev/acpica/acpi_pcib_pci.c returns -1000 as the
probe priority and it's expected that this driver gets to
attach over the common PCI bus drivers.
Without creating a LAW entry, any access to the NAND hangs the CPU.
The original intent was to add a quirk to map all of the RouterBoard's LBC
address space in one shot, which would fix it for both NAND and the CF, and
that's probably still in the cards. However, for now, this makes NAND usable
without a separate hack.
Things left before the RouterBoard can run standalone:
* Add partitions to the NAND (not specified by the FDT, which we currently
require).
* Create a YAFFS partition for the kernel. The Mikrotik boot loader requires a
4MB partition at the beginning of NAND, with a file called 'kernel' in the
root.
Create a special resource (= device special file) for management
of tags and maps, as well as for mapping memory into the address
space. DMA resources are managed using the PROTO_IOC_BUSDMA ioctl.
Part 1 implements tag creation, derivation and destruction.
BUS_PROBE_HOOVER is. Drivers like proto(4), when compiled into the
kernel or preloaded, will render your system useless by virtue of
attaching to your PCI busses.
Return BUS_PROBE_GENERIC instead. It's just the next priority up
from BUS_PROBE_HOOVER. No other meaning has been give to its use.
While BUS_PROBE_DEFAULT seems like a better candidate, it's hard
not to think that there must be some reason why these drivers
return -10000 in the first place.
Differential Revision: D2705
code update, with supporting changes in the CORE. Changes for the extended
media types, VF driver has virtual channel protocol changes, and some
register use corrections. This software change should be coordinated with
Firmware updates to your hardware, contact your support channels for that.
MFC after: 1 week
logic is now placed in the mmap hook implementation rather than requiring
it to be placed in sys/vm/vm_mmap.c. This hook allows new file types to
support mmap() as well as potentially allowing mmap() for existing file
types that do not currently support any mapping.
The vm_mmap() function is now split up into two functions. A new
vm_mmap_object() function handles the "back half" of vm_mmap() and accepts
a referenced VM object to map rather than a (handle, handle_type) tuple.
vm_mmap() is now reduced to converting a (handle, handle_type) tuple to a
a VM object and then calling vm_mmap_object() to handle the actual mapping.
The vm_mmap() function remains for use by other parts of the kernel
(e.g. device drivers and exec) but now only supports mapping vnodes,
character devices, and anonymous memory.
The mmap() system call invokes vm_mmap_object() directly with a NULL object
for anonymous mappings. For mappings using a file descriptor, the
descriptors fo_mmap() hook is invoked instead. The fo_mmap() hook is
responsible for performing type-specific checks and adjustments to
arguments as well as possibly modifying mapping parameters such as flags
or the object offset. The fo_mmap() hook routines then call
vm_mmap_object() to handle the actual mapping.
The fo_mmap() hook is optional. If it is not set, then fo_mmap() will
fail with ENODEV. A fo_mmap() hook is implemented for regular files,
character devices, and shared memory objects (created via shm_open()).
While here, consistently use the VM_PROT_* constants for the vm_prot_t
type for the 'prot' variable passed to vm_mmap() and vm_mmap_object()
as well as the vm_mmap_vnode() and vm_mmap_cdev() helper routines.
Previously some places were using the mmap()-specific PROT_* constants
instead. While this happens to work because PROT_xx == VM_PROT_xx,
using VM_PROT_* is more correct.
Differential Revision: https://reviews.freebsd.org/D2658
Reviewed by: alc (glanced over), kib
MFC after: 1 month
Sponsored by: Chelsio
