Initial version of ATMEGA USB device controller
driver. Has not been tested on real hardware yet.
The driver is based upon the AT91DCI driver.
Submitted by: Hans Petter Selasky
down will cause a fault. Check the phy power state before possibly
reading from the bb, this can happen as ar5212Reset intentionally
calls ar5212GetRfgain before bringing the bb out of reset (but we
do it here and not in the caller to guard against other possible uses).
expected in acd_fixate().
This should fix various problems folks are having with 'burncd' reporting
"burncd: ioctl(CDRIOCFIXATE): Input/output error" during the fixate phase
when "fixate" is issued together with the "data" command.
PR: 95979
Submitted by: Jaakko Heinonen <jh@saunalahti.fi>
created by atapicam is being kept opened or mounted. This is probably just
a temporary solution until we invent something better.
Reviewed by: scottl
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
Reported by: Jaakko Heinonen
o add net80211 support for a tdma vap that is built on top of the
existing adhoc-demo support
o add tdma scheduling of frame transmission to the ath driver; it's
conceivable other devices might be capable of this too in which case
they can make use of the 802.11 protocol additions etc.
o add minor bits to user tools that need to know: ifconfig to setup and
configure, new statistics in athstats, and new debug mask bits
While the architecture can support >2 slots in a TDMA BSS the current
design is intended (and tested) for only 2 slots.
Sponsored by: Intel
1.Sync TD on close to ensure USB request in close callback issued.
2.Add sysctls to indicate device role.
3.Enable handsfree port support.
Now modem port and obex port works well.
Handsfree port works but not with good response.
specifically SPI controllers now also work in big-endian
machines and some conversions relevant for FC and SAS
controllers as well as support for ILP32 machines which all
were omitted in previous attempts are now also implemented.
The IOCTL-interface is intentionally left (and where needed
actually changed) to be completely little-endian as otherwise
we would have to add conversion code for every possible
configuration page to mpt(4), which didn't seem the right
thing to do, neither did converting only half of the user-
interface to the native byte order.
This change was tested on amd64 (SAS+SPI), i386 (SAS) and
sparc64 (SAS+SPI). Due to lack of the necessary hardware
the target mode code is still left to be made endian-clean.
Reviewed by: scottl
MFC after: 1 month
functions and stop attaching of dcons(4) and dcons_crom(4) if
they indicate failure. This fixes a panic seen on sparc64 machines
with no free physical memory in the requested 32-bit region but
still doesn't make dcons(4)/dcons_crom(4) these work. I think
the latter can be fixed by simply specifying ~0UL as the upper
limit for contigmalloc(9) and letting the bounce pages and the
IOMMU respectively handle limitations of the DMA engine. I didn't
want to change that without the consensus of simokawa@ though,
who unfortunately didn't reply so far.
MFC after: 1 week
module. These files cause manual interaction when building
ports/audio/aureal-kmod which provides a usable i386-only driver (it requires
linking against some linux object files distributed by vendor which bankrupted
back in 2000).
MFC after: 1 week
subclasses as are available with PCI. Changes I2C device drivers without
real probe logic to return BUS_PROBE_NOWILDWARD to avoid interference with
firmware bus enumeration, and reduces the probe priority of the iicbus
base driver to allow subclass attachment at higher priority.
Discussed on: freebsd-arch
would fail to attach due to unsupported USB revision. It should have
no effect when running on a real hardware.
Reviewed by: imp
Approved by: rwatson (mentor)
- Implement NP (ASCII 12, Form Feed). When used with cons25, it should
clear the screen and place the cursor at the top of the screen. When
used with xterm, it should just simulate a newline.
- When we want to use xterm emulation, make teken_demo set TERM to
xterm.
Spotted by: Paul B. Mahol <onemda@gmail.com>
driver since it couldn't have worked with NEWCARD w/o these fixes.
This should allow selecting 16-bit memory width as well (which was
what was broken).
Because we now have cons25-style linewrapping, we must also use cons25-
style reverse linewrapping. This means that a ^H on column 0 will move
the cursor one line up.
Also fix a small regression: if the user invokes a RIS (Reset to Initial
State), we must show the cursor again.
Spotted by: Paul B. Mahol <onemda gmail com>
With cons25, there are printable characters below 0x1B. This is not the
case with ASCII, UTF-8, etc. but in this case we just have to.
Also don't set LC_CTYPE to UTF-8 when libteken is compiled without UTF-8
in the demo-application.
src/lib/libusb20/libusb20_desc.c
Make "libusb20_desc_foreach()" more readable.
src/sys/dev/usb2/controller/*.[ch]
src/sys/dev/usb2/core/*.[ch]
Implement support for USB power save for all HC's.
Implement support for Big-endian EHCI.
Move Huawei quirks back into "u3g" driver.
Improve device enumeration.
src/sys/dev/usb2/ethernet/*[ch]
Patches for supporting new AXE Gigabit chipset.
src/sys/dev/usb2/serial/*[ch]
Fix IOCTL return code.
src/sys/dev/usb2/wlan/*[ch]
Sync with old USB stack.
Submitted by: hps
It turns out I was looking too much at mimicing xterm, that I didn't
take the differences of cons25 into account. There are some differences
between xterm and cons25 that are important. Create a new #define called
TEKEN_CONS25 that can be toggled to switch between cons25 and xterm
mode.
- Don't forget to redraw the cursor after processing a forward/backward
tabulation.
- Implement cons25-style (WYSE?) autowrapping. This form of autowrapping
isn't that nice. It wraps the cursor when printing something on column
80. xterm wraps when printing the first character that doesn't fit.
- In cons25, a \t shouldn't overwrite previous contents, while xterm
does.
Reported by: Garrett Cooper <yanefbsd gmail com>
cells in the map, instead of using a value passed to it and then panicing if it
disagrees. This fixes interrupt map parsing for PCI bridges on some Apple
Uninorth PCI controllers.
Reported by: marcel
Tested on: G4 iBook, Sun Ultra 5
The cursor is only inside the scrolling region when we are in origin
mode. In that case, it should use originreg instead of scrollreg. It is
completely valid to place the cursor outside the scrolling region.
