environments.
In setups where NF calibration can take a while, don't load the CCA
and kick off a new NF calibration if the previous one hasn't yet
completed. This shouldn't happen unless the environment is noisy but
those exist (hi phk!).
Here, if the previous NF hasn't completed when ar5416LoadNf() is run
(which reads the NF), it skips updating the history buffer, loading
the NF CCA array and kicking off the next NF cal. It's hoped it'll
occur in the next long calibration interval.
Obtained from: Atheros, ath9k, my local HAL
This is taking quite a while for some people in some situations
(eg AR5418 in phk's Abusive Radio Environment).
Instead, the rest of the calibration related code should
ensure that a NF calibration has occured before reading NF
values and kicking off another NF calibration.
The channel should also likely be marked as "noisy" (CWINT)
if the NF calibration takes too long.
* Correct some of the silicon revision checks to match what
the Atheros HAL does. (See [1] below.)
* Move the PA cal and init cal method assignment to -after-
the mac version/revision IDs are stored. The AR9285 init
cal was never being called.
* Enable ANI.
Note Kite 1.0 and 1.1 were prototypes that shouldn't be seen
in the wild. Linux ath9k simply removed the prototype code from
their codebase. I'm going to leave it in there for now but
make it conditionally compilable in the future.
Obtained from: Atheros
newer controllers. However, all data sheet I have access has no
indication that buffer manager should not be touched on these
controllers. It seems the buffer manager always runs on BCM5705 or
newer controllers. Some controller(e.g. BCM5719) needs other buffer
manager configuration so driver should enable buffer manager for
all controllers. Both Linux and OpenBSD/NetBSD use the same
approach.
This change polls enable bit of block to know whether specified
block was really stopped as well as enabling buffer manager for all
controllers in driver initialization.
Obtained from: NetBSD
from Atheros as to what/when this is supposed to be enabled.
Using the default RX fast diversity settings seems to help quite
a bit.
Whilst I'm here, change the prototype to return HAL_BOOL rather than int.
For now, the diversity settings are controlled by 'txantenna',
-not- rxantenna. This is because the earlier chipsets had
controllable TX diversity; the RX antenna setting twiddles
the default antenna register. I'll try sort that stuff out at
some point.
Call the antenna switch function from the board setup function
so scans, channel changes, mode changes, etc don't set the
diversity back to a default state too far from what's intended.
Things to todo:
* Squirrel away the last antenna diversity/combining parameters
and restore them during board setup if HAL_ANT_VARIABLE is
defined. That way scans, etc don't reset the diversity settings.
* Add some more public facing statistics, rather than what's
simply logged under HAL_DEBUG_DIVERSITY.
For now, the fixed antenna settings behave better than variable
settings for me. I have some further fiddling to do..
Obtained from: Atheros
The macro which I incorrectly copied into ah_internal.h assumed
that it'd be called with an AR_SREV_MERLIN_20() check to ensure
it was only enabled for Merlin (AR9280) silicon revision 2.0 or
later.
Trouble is, the 5GHz fast clock EEPROM flag is only valid for
EEPROM revision 16 or greater; it's assumed to be enabled
by default for Merlin rev >= 2.0. This meant it'd be incorrectly
set for AR5416 and AR9160 in 5GHz mode.
This would have affected non-default clock timings such as SIFS,
ACK and slot time. The incorrect slot time was very likely wrong
for 5ghz mode.
* Modify AR_SREV_MERLIN_20() to match the Atheros/Linux ath9k behaviour -
its supposed to match Merlin 2.0 and later Merlin chips.
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 2.0 and later chips
(AR9285, AR9287, etc.)
- instead of calling iwn_plcp_signal() for every frame, map the expected
value directly within wn->ridx
- concat plcp, rflags and xrflags, there is no clean byte boundary within
the flags, for example the antenna setting uses bit 6, 7 and 8
- there is still need for a custom rate to plcp mapping, as those expected
by the hardware are not conform to the std
On legacy channels every once in a while the firmware throws a SYSASSERT
on line 208. On HT channels though this does always happen and I'm not
aware of any workaround currently.
for the given channel is available.
It isn't used yet; ar5416GetWirelessModes() needs to be taught
about this rather than assuming HT20/HT40 is available.
This seems to make the AR9160 behave better during heavy scanning,
where before it'd hang and require a hard reset to recover.
Obtained From: Linux ath9k, Atheros
modifying AR_DIAG_SW.
There's a hardware workaround which sets disabling some errors
early at startup and clears said bits before the PCU begins
receiving - it does this to avoid RX descriptor status errors.
It's possible these bits aren't being completely properly twiddled
in all instances; but in particular if the diag_reg HAL variable
is set it won't be setting these bits correctly. I'll review this
at some point.
* Disable multicast search on mac address and key id - the driver
doesn't use it at the moment and thus adhoc may be broken for
merlin and later.
* Change this to be for Merlin 1.0 (which from what I understand
wasn't ever publicly released) to be more correct.
Apparently all three RX chains need to be enabled before initial calibration
is done, even if only two are configured.
Reorder the alt chain swap bit to match what the Atheros HAL is doing.
Obtained From: ath9k, Atheros
* Shuffle some of the capability numbers around to match the
Atheros HAL capability IDs, just for consistency.
* Add some new capabilities to FreeBSD from the Atheros
HAL which will be be shortly used when new chipsets are added
(HAL SGI-20 support is for Kiwi/AR9287 support); for
TX aggregation (MBSSID aggregate support, WDS aggregation
support); CST/GTT support for carrier sense/TX timeout.
channel when the channel is HT/40.
The new ANI code (primarily for the AR9300/AR9400) in ath9k sets this
register but the ANI code for the previous 11n chips didn't set this.
Unlike ath9k, only set this for HT/40 channels.
Obtained From: ath9k
