While we end up the same place, we end up with two different CS register
values after the jump and 0xf000 is compatible with the hardware reset
value.
This makes a difference if the BIOS does a near jump before a far jump.
Detective work and patch by: Adrian Steinmann <ast@marabu.ch>
- improve sysinfo(2) syscall;
- add dummy fadvise64(2) syscall;
- add dummy *xattr(2) family of syscalls;
- add protos for the syscalls 222-225, 238-249 and 253-267;
- add exit_group(2) syscall, which is currently just wired to exit(2).
Obtained from: OpenBSD
MFC after: 2 weeks
Its restoration in rev.1.102 was mistranslated to the equivalent of
setsofttty() in rev.1.105. This increased overheads by causing a
context switch to the SWI handler after almost every interrupt. The
increase was approx. 50% on a Celeron 366 (from 23 usec to 34 usec
per interrupt).
I'm having bad luck with different parts of the sys tree being checked
out at slightly different times. Back it out, noting it doesn't cause
harm in any case. Tinderbox also makes these things more fun.
of newfs, to signify the newfs operation has not yet completed. Re-
write the superblock with the correct magic number once all of the
cylinder groups have been created to show the operation has finished.
Sponsored by: St. Bernard Software
physical mapping.
- Move the sf_buf API to its own header file; make struct sf_buf's
definition machine dependent. In this commit, we remove an
unnecessary field from struct sf_buf on the alpha, amd64, and ia64.
Ultimately, we may eliminate struct sf_buf on those architecures
except as an opaque pointer that references a vm page.
sure to sooptcopyin() the (struct mac) so that the MAC Framework
knows which label types are being requested. This fixes process
queries of socket labels.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
opt_ddb.h. These changes expand green's work of including
opt_global.h to prefer opt files in the kernel directory. Further
refinement might be needed, but I think this is good.
Note: While this is a step on the path to moving the meta information
about modules into the config files, it doesn't actually do that. It
just pulls in the opt files in a way that allows one to build
'generic' modules outside the tree.
disposing fifo resources in fifo_cleanup() instead using of
"vp->v_usecount == 1". There may be other references to the vnode, for
instance by nullfs, at the time fifo_open() or fifo_close() is called,
which could cause a resource leak.
Don't bother grabbing the vnode interlock in fifo_cleanup() since it no
longer accesses v_usecount.
the nfsv4 files. It is intended to be a short-term bridge while
alfred deals with the problem in a better way (eg, don't hesitate to
back this out when the real fix comes along). I've not heard back
from alfred in a few hours and other people are hitting this problem.
Approved by: markm, rwatson, grog, murray
problem, but the spamage of consoles is really bad. Until we can get
this to be less chatty, disable it so people can boot. The badness of
the spamage is worse than the badness that it reports :-(. Once the
underlying problems have been fixed, it can be reenabled.
Approved by: kken, markm, rwatson, grog, murray
* Use the cpu_idle_hook() to do idling for C1-C3.
* Use both _CST and the FADT to detect Cx states.
* Use both _PTC and P_CNT for controlling throttling.
* Add a notify handler to detect changes in _CST and _PSS
* Call the _INI function for each processor if present. This will be
done by ACPI-CA in the future.
* Fix a bug on SMP systems where CPUs will attach multiple times if the
bus is rescan.
* Document new sysctls for controlling idling.
and remove two unneccessary variable initializations.
Make the introduction comment more clear with regard which parts of
the packet are touched.
Requested by: luigi
value as reserved for internal use in boot blocks, because RB_PAUSE
broke binary compatibility by usurping the RB_DUAL flag. Probably no
one except me has boot blocks for which this matters, since most boot
blocks based on biosboot including pc98's boot2 can't boot elf kernels,
and /boot/loader doesn't properly pass flags set by the previous stage.
reboot.h:
Also mark the historical RB_PROBEKBD flag (0x80000) as reserved for
internal use in boot blocks.
boot2.c:
Added comments to inhibit usurping of other flags.
Approved by: guido, imp
MFC after: 1 week
on non-VCHR vnodes. This fixes a panic when reading data from files on a
filesystem with a small (less than a page) block size.
PR: 59271
Reviewed by: alc
kses from the run queues. Also, on SMP, we track the transferable
count here. Threads are transferable only as long as they are on the
run queue.
- Previously, we adjusted our load balancing based on the transferable count
minus the number of actual cpus. This was done to account for the threads
which were likely to be running. All of this logic is simpler now that
transferable accounts for only those threads which can actually be taken.
Updated various places in sched_add() and kseq_balance() to account for
this.
- Rename kseq_{add,rem} to kseq_load_{add,rem} to reflect what they're
really doing. The load is accounted for seperately from the runq because
the load is accounted for even as the thread is running.
- Fix a bug in sched_class() where we weren't properly using the PRI_BASE()
version of the kg_pri_class.
- Add a large comment that describes the impact of a seemingly simple
conditional in sched_add().
- Also in sched_add() check the transferable count and KSE_CAN_MIGRATE()
prior to checking kseq_idle. This reduces the frequency of access for
kseq_idle which is a shared resource.
- missing parenthesization of some macro args
- point of do-while(0) hack defeated by putting a semicolon after while(0)
Fixed some style bugs in macros:
- not splitting the line when the macro value cannot be lined up in much
the same macros that didn't parenthesize their args
- braces around a 1-line statement
- do-while(0) hack not indented in the usual way in the same macros that
defeated its point.
