The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
tulip_addr_filter() on SIOCSIFFLAGS, and was nuking the IFF_ALLMULTI
on entering tulip_addr_filter(). As a result it was impossible to run
a multicast router on a machine with a "de" interface.
Added autodetection of MMAC Osprey 100 card for
Jan Schmidt <mmedia@rz.uni-greifswald.de>. The MMAC card has an EEPROM
which contains an ASCII string beginning with "MMAC".
Corrected Hauppauge Audio Mux Mute value from 0x01 to 0x04.
Fixed a typo.
Sumitted change:
Added ALPS Tuner Type submitted by Hiroki Mori <mori@infocity.co.jp>
Submitted by: Roger Hardiman and Hiroki Mori <mori@infocity.co.jp>
Addtron appear to have their own VIA Rhine II and RealTek 8139 boards
with custom PCI vendor and device IDs. This commit updates the PCI
vendor and device lists in the vr and rl drivers so that we can probe
the additional devices.
Found by: nosing around the PCI vendor and device code list at:
http://www.halcyon.com/scripts/jboemler/pci/pcicode
This is for various Olicom cards. An IBM driver is following.
This patch also adds support to tcpdump to decode packets on tokenring.
Congratulations to the proud father.. (below)
Submitted by: Larry Lile <lile@stdio.com>
Seems to solve a problem with a mouse not responding to movements in the
X direction. Problem description is still rather vague and solution is
not exactly clear. Problem might be a compiler optimisation.
driver was thinking irq was enabled although it wasn't.
This case was particular to a no-interrupt static configuration.
Reported by: "Norman C. Rice" <nrice@emu.sourcee.com>
Now should be able to report speed for cards using NatSemi PHY.
(if you have one please let me know if it works as I
only have the Intel version)
Reviewed by: David Greenman <dg@root.com>
Submitted by Roger Hardiman.
Added ioctl TVTUNER_GETCHANSET to discover which regions the bktr driver
supports. Submitted by Vsevolod Lobko <seva@alex-ua.com>
Added BT848_GPIO_SET_EN,BT848_GPIO_SET_DATA (and GETs) to allow user land
control of the GPIO pins. This allows a Radio module on the GPIO port
to be controlled. Submitted by Vsevolod Lobko <seva@alex-ua.com>
The kernel option BKTR_GPIO_ACCESS must be used to enable the GPIO ioctls.
Submitted by: Roger Hardiman and Vsevolod Lobko <seva@alex-ua.com>
the same name. Silently return EEXIST if this happens.
vinum_scandisk: Collect drive numbers, not pointers, to avoid problems
of relocated drives.
Tripped-over-by: Bernd Walter <ticso@cicely.de>
time out on an operation. Under these circumstances, vinum(8) will
automatically start another daemon. Add a pid for the daemon, so that
an overtaken daemon will discover that it's no longer in favour, and
will crawl into a corner and die.
peripheral drivers can determine where in the devstat(9) list they are
inserted.
This requires recompilation of libdevstat, systat, vmstat, rpc.rstatd, and
any ports that depend on the devstat code, since the size of the devstat
structure has changed. The devstat version number has been incremented as
well to reflect the change.
This sorts devices in the devstat list in "more interesting" to "less
interesting" order. So, for instance, da devices are now more important
than floppy drives, and so will appear before floppy drives in the default
output from systat, iostat, vmstat, etc.
The order of devices is, for now, kept in a central table in devicestat.h.
If individual drivers were able to make a meaningful decision on what
priority they should be at attach time, we could consider splitting the
priority information out into the various drivers. For now, though, they
have no way of knowing that, so it's easier to put them in an easy to find
table.
Also, move the checkversion() call in vmstat(8) to a more logical place.
Thanks to Bruce and David O'Brien for suggestions, for reviewing this, and
for putting up with the long time it has taken me to commit it. Bruce did
object somewhat to the central priority table (he would rather the
priorities be distributed in each driver), so his objection is duly noted
here.
Reviewed by: bde, obrien
define. Add a new config flag param (ISP_CFG_NONVRAM) whose intent it is
to cause NVRAM to be ignored. Add ISPASYNC_LOOP_DOWN and ISPASYNC_LOOP_UP
isp_async enums.
Amazingly enough, I did all my scsi_sa work recently without realizing
that I had a broken isp card whose (unchangeable- it's an old old old
isp1020) NVRAM has sync mode enabled, but disconnect/reconnect disabled-
the ISP_CFG_NONVRAM is definitely warranted when you want to bloody well
ignore the NVRAM and set something sensible.
Use fast memory timing NVRAM parameter. Clean up and fix establishment
of default target parameters. Don't use NVRAM if are flagged as not to
do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC
mode but disabled disconnect/reconnect and wide!!). Fix delays after
resets. BUS resets not done in isp_init anymore- relegated to OS
specific outer layers. Fix a buglet where you can get in a loop for
a NULL xs in the completion list in isp_intr. Add in some defines that
can disable fast posting. Add in code for Loop Up/Loop Down events that
call into the outer layers as to what to do.
Do not modify m_len before passing mbuf chains to bpf.
Don't forget to pass packets to bpf when running in Crynwr mode (LINK0).
Partially based on a patch by Bill Fenner <fenner@freebsd.org>.
PR: bin/7241
Improved MSP34xx reset for bt848 Hauppauge boards.
Added detection for Bt848a.
Vsevolod Lobko<seva@sevasoft.alex-ua.com> added more XUSSR channels.
Submitted by: parts from Vsevolod Lobko<seva@sevasoft.alex-ua.com>
Obtained from: parts from OpenBSD
the screen width.
- Store the current video mode information in the `video_adapter' struct.
- The size of the `v_offscreensize' field in the VESA mode information
block is u_int16, not u_int8.
Increase the overall length of the delay by 10.
Without this a 3C509 card on my MediaGX crash box can't be reliably
read. With this it is solid.
I've left a delay multiplier in instead of just changing the base
delay because I'm surprised I had to increase it so much and expect
there may be another problem.
Change microseq offsets. Previously, offsets of the program counter where
added to the index of the current microinstruction. Make them rely on the
index of the next executed microinstruction.
Suggested by: Luigi Rizzo <luigi@labinfo.iet.unipi.it>
the startup code. Implement a call to outer framework function so that
asynchronous events can be handled (e.g., speed negotiation, target mode).
Roll internal release tags.
cycle to get rid of the old 1.31 firmware. *@!$&^@&$!&^&^!!!!!
But anyway comment it out and use new SBus 7.55 firmware. We get fast posting
with this as well as 32 luns and target mode support.
(not that this is used yet in FreeBSD, but it's ready for FreeBSD-sparc
whenever it happens....)
v_caddr_t with extreme prejudice. Here the bogons were originally
the same as for c_caddr_t (half-baked K&R support), but rev.1.95
changed one wrong cast and one harmless cast to 2 wrong casts,
and rev.1.96 only fixed the originally wrong cast.
c_caddr_t with extreme prejudice. Here the original casts to
caddr_t were to support K&R compilers (or missing prototypes),
but the relevant source files require an ANSI compiler.
apparently in accordance with style(9).
Complained-about-by: bde
vinumopen: Change check for root user to a call to suser(9)
vinumclose: Remove check for root user.
Nitpicked-by: phk
Auto Detection Mode. This leaves MSP3400C owners still unsupported.
Thanks to Gerd Knorr <kraxel@cs.tu-berlin.de> for providing some early
assistance and sample code in the linux bttv driver.
Nicolas Souchu <nsouch@freebsd.org> ported the msp_read/write/reset
functions to smbus/iicbus.
METEOR_INPUT_DEV2 now selects a composite camera on the SVIDEO port.
For true SVIDEO, use METEOR_INPUT_DEV_SVIDEO.
If you get a monochrome image from the SVIDEO port, you have
seleted the wrong input type.
Tested by: Johan Larsson<gozer@ludd.luth.se>
keyboard.
- Translate some keycode for the 84 keyboard so that the 84 keyboard
and the 101 keyboard become more compatible in terms of keycodes.
- Updated the built-in keymaps so that it is in line with the recent
changes in share/syscons/keymaps.
- Added some comment on the Pause/Break key on the 101 keyboard.
vinum_scandisk: check not only drive error, but also drive state,
before accessing the drive.
drivecmp: Remove warning messages by Backing out overly constant
declarations in revision 1.9.
