TX/RX checksum handler to set/clear relavant assist bits which was
used to cause unexpected results.
With this change, bce(4) can be bridged with other interfaces that
lack TSO, VLAN checksum offloading.
Reviewed by: davidch
around. Management firmware(ASF/IPMI/UMP) requires the VLAN
hardware tag stripping so don't actually disable VLAN hardware tag
stripping. If VLAN hardware tag stripping was disabled, bce(4)
manually reconstruct VLAN frame by appending stripped VLAN tag.
Also remove unnecessary IFCAP_VLAN_MTU message.
Reviewed by: davidch
for controllers like 88E8053 which reports two MSI messages.
Because we don't get anything useful things with 2 MSI messages,
allocating 1 MSI message would be more sane approach.
While I'm here, enable MSI for dual-port controllers too. Because
status block is shared for dual-port controllers, I don't think
msk(4) will encounter problem for using MSI on dual-port
controllers.
The register offset is not valid on 88E8072 controller. Also don't
blindly increase max read request size to 4096, instead, use 2048
which seems to be more sane value and only change the value if the
hardware default size(512) was used on that register.
For PCIX controllers, use system defined constant rather than using
magic value.
While I'm here stop showing negotiated link width.
not require checksum LE configuration if checksum start and write
position is the same as before. So keep track last checksum start
and write position and insert new LE whenever the position is
changed. This reduces number of LEs used in TX path as well as
slightly enhance TX performance.
been around for a long time now (7.1-ish or even earlier); assume
they are present. These includes MSI, TSO, LRO, VLAN, INTR_FILTERS,
FIRMWARE, etc.
Also, eliminate some dead code and clean up in other places as part
of this quick once-over.
MFC after: 1 week
race as it could already have been tx'd and freed by that time. Place
the bpf tap just _before_ writing the gen bit.
This fixes a panic when running tcpdump on a cxgb interface.
- Add a separate palette data for 8-bit DAC mode when SC_PIXEL_MODE is set
and fill it up with default gray-scale palette data for text. Now we don't
have to set `hint.sc.0.vesa_mode' to get the default palette data.
- Add a new adapter flag, V_ADP_DAC8 to track whether the controller is
using 8-bit palette format and load correct palette when switching modes.
- Set 8-bit DAC mode only for non-VGA compatible graphics mode.
change and have isp_make_here scan the whole bus which will then scan all
luns.
I think xpt_rescan needs to be fixed, but that's a separable issue.
Suggested by: Alexander
not support TSO over VLAN if VLAN hardware tagging is disabled so
there is no need to check VLAN here.
While I'm here make sure to pullup IP/TCP headers in the first
buffer.
GEM_MIF_CONFIG_MDI0 cannot be trusted when the firmware has powered
down the chip so the internal transceiver has to be hardcoded. This
is also in line with the AppleGMACEthernet driver, which just doesn't
distinguish between internal/external transceiver and MDIO/MDI1
respectively in the first place. Tested by: Andreas Tobler
MFC after: 1 week
frame, make sure to update VLAN capabilities whenever jumbo frame
is configured.
While I'm here rearrange interface capabilities configuration. The
controller requires VLAN hardware tagging to make TSO work on VLANs
so explicitly check this requirement.
Tx DMA burst size 2048, I beleive PCIe maximum read request size
also should match to the value of Tx DMA burst size. With this
change I can get more than 800Mbps for TCP bulk transfers.
Previously I was not able to get more than 700Mbps. If I enable TSO
it now shows 927Mbps.
to make TSO work on VLAN. So if VLAN hardware tagging is disabled
explicitly clear TSO on VLAN. While I'm here remove duplicated
VLAN_CAPABILITIES call.
o uses v4 firmware instead of v3. A port will be committed to create
the bwn firmware module.
o supports B/G and LP(low power) PHYs.
o supports 32 / 64 bits DMA operations.
o tested on big / little endian machines so should work on all
architectures.
It'd not connected to the build until the firmware port is committed.
