We observe at least one problem: if a UDP socket is connect(2)-ed, then a
received packet that matches the connection cannot be matched to the
corresponding PCB because of an incorrect flow ID. That was oberved for DNS
requests from the libc resolver. We got this problem because FreeBSD
r343291 enabled code that can set rsstype of received packets to values
other than M_HASHTYPE_OPAQUE_HASH. Earlier that code was under 'ifdef
notyet'.
The essence of this change is to use the system-wide RSS key instead of
some historic hardcoded key when the software RSS is enabled and it is
configured to use Toeplitz algorithm (the default).
In all other cases, the driver reports the opaque hash type for received
packets while still using Toeplitz algorithm with the internal key.
PR: 242890
Reviewed by: pkelsey
Sponsored by: Panzura
Differential Revision: https://reviews.freebsd.org/D23147
This bus does not really have a concept of the initiator ID, so use
a guaranteed dummy one that won't conflict with any real target.
This change fixes a problem with virtio_scsi on GCE where disks get
sequential target IDs starting from one. If there are seven or more
disks, then a disk with the target ID of seven would not be discovered
by FreeBSD as that ID was reserved as the initiator ID -- see
scsi_scan_bus().
Discussed with: bryanv
MFC after: 2 weeks
Sponsored by: Panzura
supposedly may call into ether_input() without network epoch.
They all need to be reviewed before 13.0-RELEASE. Some may need
be fixed. The flag is not planned to be used in the kernel for
a long time.
The vnode pager does not want the object lock held. Moving this out allows
further object lock scope reduction in callers. While here add some missing
paging in progress calls and an assert. The object handle is now protected
explicitly with pip.
Reviewed by: kib, markj
Differential Revision: https://reviews.freebsd.org/D23033
On a MINIMAL kernel, mps.ko wouldn't load because it uses the xpt_hold_boot
symbol from CAM, but didn't have a dependency on cam(4).
(CEM: Some context: when linking loaded modules, the kernel dynamic linker
only looks for definitions in explictly marked dependency modules. Also,
the identical mpr(4) driver uses the same CAM function, but already had the
correct MODULE_DEPEND(), so no similar change is needed there.)
Submitted by: Greg V <greg AT unrelenting.technology>
Reviewed by: imp, myself
Differential Revision: https://reviews.freebsd.org/D23272
This is a qspi driver for the Xilinx Zynq-7000 chip.
It could be useful for anyone wanting to boot a system from flash memory
instead of SD cards.
Submitted by: Thomas Skibo (thomasskibo@yahoo.com)
Differential Revision: https://reviews.freebsd.org/D14698
Most of the gpio controller cannot configure or get the configuration
of the pin muxing as it's usually handled in the pinctrl driver.
But they can know what is the pinmuxing driver either because they are
child of it or via the gpio-range property.
Add some new methods to fdt_pinctrl that a pin controller can implement.
Some methods are :
fdt_pinctrl_is_gpio: Use to know if the pin in the gpio mode
fdt_pinctrl_set_flags: Set the flags of the pin (pullup/pulldown etc ...)
fdt_pinctrl_get_flags: Get the flags of the pin (pullup/pulldown etc ...)
The defaults method returns EOPNOTSUPP.
Reviewed by: ian, bcr (manpages)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23093
Some consumer cannot know the voltage of the regulator without it.
While here, refuse to attach is min_voltage != max_voltage, it
shouldn't happens anyway.
Reviewed by: mmel
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23003
This change is based on Linux commit 40630f462824ee. csio.resid should
account for transfer_len only for success and SRB_STATUS_DATA_OVERRUN
condition.
I am not sure how exactly this change works, but I have a report from a
user that they see lots of checksum errors when running a pool scrub
concurrently with iozone -l 1 -s 100G. After applying this patch the
problem cannot be reproduced.
Reviewed by: nobody
Sponsored by: CyberSecure
Differential Revision: https://reviews.freebsd.org/D22312
than 128MB, which is the maximum supported by the hardware in RDMA mode.
Obtained from: Chelsio Communications
MFC after: 3 days
Sponsored by: Chelsio Communications
The netmap passthrough subsystem requires proper support in the
hypervisor. In particular, two PCI device ids (from the Red Hat
PCI vendor id 0x1b36) need to be assigned to the two netmap
virtual devices. We then disable these devices until the ids have
not been assigned, in order to avoid conflicts with other
virtual devices emulated by upstream QEMU.
PR: 241774
MFC after: 3 days
Fix a mistake introduced by r343291, which ported the vmx(4)
driver to iflib.
In case of TSO, the hlen field of the (first) tx descriptor must
be initialized to the cumulative length of Ethernet, IP and TCP
headers. The length of the TCP header was missing.
PR: 236999
Reported by: pkelsey
Reviewed by: avg
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D22967
Highlights:
- Exit early if we're not disabling unused regulators; there's no need to
take the regulator topology lock and re-evaluate this every iteration, as
it's not going to change.
- Don't emit a notice that we're shutting down a regulator if it's not
enabled, to reduce noise.
- Mention the outcome of the shutdown, to aide debugging and easily let
developer/user collect list of regulators we actually shutdown to
determine problematic one.
Reviewed by: manu
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D22213
The patch could be simplier, using only the second chunk to
vtnet_rxq_eof(), that passes full mbufs to pfil(9). Packet
filter would m_free() them in case of returning PFIL_DROPPED.
However, we pretend to be a hardware driver, so we first try
to pass a memory buffer via PFIL_MEMPTR feature. This is mostly
done for debugging purposes, so that one can experiment in bhyve
with packet filters utilizing same features as a true driver.
We use to handle each message separately in i2c_transfer but that cannot
work with message with NOSTOP as it confuses the controller that we disable
the interrupts and start a new message.
Handle every message in the interrupt handler and fire a new start condition
if the previous message have NOSTOP, the controller understand this as a
repeated start.
This fixes booting on Allwinner A10/A20 platform where before the i2c controller
used to write 0 to the PMIC register that control the regulators as it though that
this was the continuation of the write message.
Tested on: A20 BananaPi, Cubieboard 1 (kevans)
Reported by: kevans
MFC after: 1 month
This avoids getting the XHCI_TRB_ERROR_CONTEXT_STATE error code from the XHCI
controller when the endpoint is disabled or already stopped.
Suggested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
The newer versions of RPi FDT flipped the order of the interrupts
specification and added an 'interrupt-names' property for driver aide in
finding the correct interrupt, rather than assuming the positions. Use it if
it's available, or fallback to the old method if there is no interrupt-names
property with a usb value.
This has been tested with both old RPi3B FDT and new RPi3B FDT, USB again
works on the latter.
Reported by: Tom Yan <tom.ty89 gmail com>
MFC after: 3 days
Do not configure any endpoint twice, but instead keep track of which
endpoints are configured on a per device basis, and use an evaluate
endpoint context command instead. When changing the configuration make
sure all endpoints get deconfigured and the configured endpoint mask
is reset.
This fixes an issue where an endpoint might stop working if there is
an error and the endpoint needs to be reconfigured as a part of the
error recovery mechanism in the FreeBSD USB stack.
Tested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
Virtualise tcp_always_keepalive, TCP and UDP log_in_vain. All three are
set in the netoptions startup script, which we would love to run for VNETs
as well [1].
While virtualising the log_in_vain sysctls seems pointles at first for as
long as the kernel message buffer is not virtualised, it at least allows
an administrator to debug the base system or an individual jail if needed
without turning the logging on for all jails running on a system.
PR: 243193 [1]
MFC after: 2 weeks
Move the decision to take an early exit from that function after adding
children based on FDT data into the #ifdef FDT block, so that it doesn't
offend coverity's notion of how the code should be written. (What's the
point of compilers optimizing away dead code if static analyzers won't
let you use the feature in conjuction with an #ifdef block?)
Reported by: coverity via vangyzen@
has a non-NULL child bus stored in it, so the "none" value can't be zero
since that's a valid array index. Also, when adding all possible buses
because there is no specific per-bus config, there's no need to reset
sc->maxbus on each loop iteration, it can be set once after the loop.
This method is supposed to write the voltage into uvolt
and return an errno compatible value.
Reviewed by: mmel
Differential Revision: https://reviews.freebsd.org/D23006
Don't wait until the vtnet_debugnet_init() call happens, because at that
point we might already have allocated something from
vtnet_tx_header_zone.
Some systems showed this panic:
vtnet0: link state changed to UP
panic: keg vtnet_tx_hdr initialization after use.
cpuid = 5
time = 1578427700
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xfffffe004db427f0
vpanic() at vpanic+0x17e/frame 0xfffffe004db42850
panic() at panic+0x43/frame 0xfffffe004db428b0
uma_zone_reserve() at uma_zone_reserve+0xf6/frame 0xfffffe004db428f0
vtnet_debugnet_init() at vtnet_debugnet_init+0x77/frame 0xfffffe004db42930
debugnet_any_ifnet_update() at debugnet_any_ifnet_update+0x42/frame 0xfffffe004db42980
do_link_state_change() at do_link_state_change+0x1b3/frame 0xfffffe004db429d0
taskqueue_run_locked() at taskqueue_run_locked+0x178/frame 0xfffffe004db42a30
taskqueue_run() at taskqueue_run+0x4d/frame 0xfffffe004db42a50
ithread_loop() at ithread_loop+0x1d6/frame 0xfffffe004db42ab0
fork_exit() at fork_exit+0x80/frame 0xfffffe004db42af0
fork_trampoline() at fork_trampoline+0xe/frame 0xfffffe004db42af0
--- trap 0, rip = 0, rsp = 0, rbp = 0 ---
KDB: enter: panic
[ thread pid 12 tid 100011 ]
Stopped at kdb_enter+0x37: movq $0,0x1084eb6(%rip)
db>
Reviewed by: cem, markj
Differential Revision: https://reviews.freebsd.org/D23073
SSD capacity in laptops is growing faster then RAM size, so my original
guess seems too low on second thought. Hopefully nobody will build large
array of those crappy SSDs.
MFC after: 2 weeks
X-MFC-with: 356474
This allows cheapest DRAM-less NVMe SSDs to use some of host RAM (about
1MB per 1GB on the devices I have) for its metadata cache, significantly
improving random I/O performance. Device reports minimal and preferable
size of the buffer. The code limits it to 1% of physical RAM by default.
If the buffer can not be allocated or below minimal size, the device will
just have to work without it.
MFC after: 2 weeks
Relnotes: yes
Sponsored by: iXsystems, Inc.
In PR 243056 a user reports some spam from smartpqi(4). In particular,
the driver warns about an unrecognized PQI_CONF_TABLE_SECTION_SOFT_RESET
section (not yet defined in the driver, but handled in Linux), but this
doesn't cause any problems. The Linux driver also does not warn about
unrecognized sections.
Also do not log a warning when a device is added, since this is routine.
Lower severity to DISC, to match pqisrc_remove_device().
PR: 243056
Reviewed by: sbruno
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D23023
Filesystems which want to use it in limited capacity can employ the
VOP_UNLOCK_FLAGS macro.
Reviewed by: kib (previous version)
Differential Revision: https://reviews.freebsd.org/D21427
r356147 removed a vm_page_activate() call, but this is required to
ensure that pages end up in the page queues in the first place.
Restore the pre-r356157 logic. Now, without the page lock, the
vm_page_active() check is racy, but this race is harmless.
Reviewed by: alc, kib
Reported and tested by: pho
Differential Revision: https://reviews.freebsd.org/D23024
Add a privilege check to the ixl_handle_nvmupd_cmd function, ensuring
that only privileged users are allowed to access the NVM update
interface.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reported by: markj@
Reviewed by: markj@, erj@, jeffrey.e.pieper@intel.com
MFC after: 3 days
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D22870
This will soon be a dependency for machine/atomic.h on mips with the
introduction of 64-bit atomics; the scope here is pretty narrow, so throw it
here in the header just before systm.h, which includes machine/atomic.h
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
