between kernel virtual address and physical address anymore. This so
that we can link the kernel at some virtual address without having
to worry whether the corresponding physical memory exists and is
available. The PBVM uses 64KB pages that are mapped to physical
addresses using a page table. The page table is at least 1 EFI page
in size, but can grow up to 1MB. This effectively gives us a memory
size between 32MB and 8GB -- i.e. enough to load a DVD image if one
wants to.
The loader assigns physical memory based on the EFI memory map and
makes sure that all physical memory is naturally aligned and a power
of 2. At this time there's no consideration for allocating physical
memory that is close to the BSP.
The kernel is informed about the physical address of the page table
and its size and can locate all PBVM pages through it.
The loader does not wire the PBVM page table yet. Instead it wires
all of the PBVM with a single translation. This is fine for now,
but a follow-up commit will fix it. We cannot handle more than 32MB
right now.
Note that the loader will map as much of the loaded kernel and
modules as possible, but it's up to the kernel to handle page faults
for references that aren't mapped. To make that easier, the page
table is mapped at a fixed virtual address.
o bunch of variables are turned into uint8_t
o initial setting of namep[] in lookup() is removed
as it's only overwritten a few lines down
o kname is explicitly initialized in main() as BSS
in boot2 is not zeroed
o the setting and reading of "fmt" in load() is removed
o buf in printf() is made static to save space
Reviewed by: jhb
Tested by: me and Fabian Keil <freebsd-listen fabiankeil de>
This patch shrinks boot2 a little.
o It switches kname to be just a pointer instead of an array.
o It changes ioctl to unsigned from uint8_t.
o It changes the second keyhit limit to 3 seconds from 5.
o It removes bi_basemem/bi_extmem/bi_memsizes_valid setting.
o It switches kname to be just a pointer instead of an array
thus avoiding a couple of memcpy()s.
o It changes ioctl to unsigned from uint8_t.
o It changes the second keyhit limit to 3 seconds from 5
so that constant propagation can take place.
o It changes the ticks overflow computation as suggested by bde@.
o It removes bi_basemem/bi_extmem/bi_memsizes_valid setting from
bootinfo as it is unused.
Reviewed by: jhb
Few new things available from now on:
- Data deduplication.
- Triple parity RAIDZ (RAIDZ3).
- zfs diff.
- zpool split.
- Snapshot holds.
- zpool import -F. Allows to rewind corrupted pool to earlier
transaction group.
- Possibility to import pool in read-only mode.
MFC after: 1 month
It used to choke on the notation "inb (%dx),%al" for "inb %dx,%al"; GNU
as accepts both forms. Which notation is more 'correct' is an open
question. :)
In sys/boot/i386/boot2/boot2.c, change the type of the 'opts' variable
from uint16_t back to uint32_t. The actual option bitmasks (RB_* and
RBX_*) assume at least a 32 bit variable.
Submitted by: rdivacky
x86 CPU support, better support for powerpc64, some new directives, and
many other things. Bump __FreeBSD_version, and add a note to UPDATING.
Thanks to the many people that have helped to test this.
Obtained from: projects/binutils-2.17
on space for clang and a.out support is only needed for /boot/loader,
they are excess bytes that serve no useful purpose other than to
support really old kernels (FreeBSD < 3.2 or so). Prefer clang
support over support for these old kernels and remove this code. We
gain about 100 bytes of space this way.
Reviewed by: rdivacky@
little further. This gets us further on the way to be able to build it
successfully with clang. Using in-tree gcc, this shrinks boot2.bin with
60 bytes, the in-tree clang shaves off 72 bytes, and ToT clang 84 bytes.
Submitted by: rdivacky
Reviewed by: imp
available on firmwares 3.15 and earlier.
Caveats: Support for the internal SATA controller is currently missing,
as is support for framebuffer resolutions other than 720x480. These
deficiencies will be remedied soon.
Special thanks to Peter Grehan for providing the hardware that made this
port possible, and thanks to Geoff Levand of Sony Computer Entertainment
for advice on the LV1 hypervisor.
The controller is commonly found on DM&P Vortex86 x86 SoC. The
driver supports all hardware features except flow control. The
flow control was intentionally disabled due to silicon bug.
DM&P Electronics, Inc. provided all necessary information including
sample board to write driver and answered many questions I had.
Many thanks for their support of FreeBSD.
H/W donated by: DM&P Electronics, Inc.
much space as needed for the mode buffer. Use strcmp, relying on OF giving
back NULL terminated strings.
Submitted by: marius
Approved by: nwhitehorn (mentor)
virtual mode. In virtual mode we have to do memory mapping. On PowerMacs it is
usually false while on pSeries we have found that it is true. The real-mode?
property is not available on sparc64.
Approved by: nwhitehorn (mentor)
BIOS does not support ACPI. The other options in the menu retain their
existing numbers, option 2 is simply blanked out (and '2' is ignored).
MFC after: 1 month
This is the same change that was made in rev 1.33 of boot/i386/btx/btx/btx.S
PR: i386/91871
Submitted by: Bjorn Konig <bkoenig at cs.tu-berlin.de>
MFC after: 1 week
to move the .IA_64.unwind and .IA_64.unwind_info input sections into
separate output sections.
Otherwise ld will complain about it (".data has both ordered
[`.IA_64.unwind'] and unordered [`.IA_64.unwind_info'] sections").
This makes ia64 buildworld run to full completion.
was incorrect as further down the road cons_probe() calls malloc() so the
former can't be called before init_heap() has succeed. Instead just exit
to the firmware in case init_heap() fails like OF_init() does when hitting
a problem as we're then likely running in a very broken environment where
hardly anything can be trusted to work.
OF loader on systems where address cells and size cells are both 2 (the
Mambo simulator) and fix an error where cons_probe() was called before
init_heap() but used malloc() to set environment variables.
MFC after: 1 month
clean up most layering violations:
sys/boot/i386/common/rbx.h:
RBX_* defines
OPT_SET()
OPT_CHECK()
sys/boot/common/util.[ch]:
memcpy()
memset()
memcmp()
bcpy()
bzero()
bcmp()
strcmp()
strncmp() [new]
strcpy()
strcat()
strchr()
strlen()
printf()
sys/boot/i386/common/cons.[ch]:
ioctrl
putc()
xputc()
putchar()
getc()
xgetc()
keyhit() [now takes number of seconds as an argument]
getstr()
sys/boot/i386/common/drv.[ch]:
struct dsk
drvread()
drvwrite() [new]
drvsize() [new]
sys/boot/common/crc32.[ch] [new]
sys/boot/common/gpt.[ch] [new]
- Teach gptboot and gptzfsboot about new files. I haven't touched the
rest, but there is still a lot of code duplication to be removed.
- Implement full GPT support. Currently we just read primary header and
partition table and don't care about checksums, etc. After this change we
verify checksums of primary header and primary partition table and if
there is a problem we fall back to backup header and backup partition
table.
- Clean up most messages to use prefix of boot program, so in case of an
error we know where the error comes from, eg.:
gptboot: unable to read primary GPT header
- If we can't boot, print boot prompt only once and not every five
seconds.
- Honour newly added GPT attributes:
bootme - this is bootable partition
bootonce - try to boot from this partition only once
bootfailed - we failed to boot from this partition
- Change boot order of gptboot to the following:
1. Try to boot from all the partitions that have both 'bootme'
and 'bootonce' attributes one by one.
2. Try to boot from all the partitions that have only 'bootme'
attribute one by one.
3. If there are no partitions with 'bootme' attribute, boot from
the first UFS partition.
- The 'bootonce' functionality is implemented in the following way:
1. Walk through all the partitions and when 'bootonce'
attribute is found without 'bootme' attribute, remove
'bootonce' attribute and set 'bootfailed' attribute.
'bootonce' attribute alone means that we tried to boot from
this partition, but boot failed after leaving gptboot and
machine was restarted.
2. Find partition with both 'bootme' and 'bootonce' attributes.
3. Remove 'bootme' attribute.
4. Try to execute /boot/loader or /boot/kernel/kernel from that
partition. If succeeded we stop here.
5. If execution failed, remove 'bootonce' and set 'bootfailed'.
6. Go to 2.
If whole boot succeeded there is new /etc/rc.d/gptboot script coming
that will log all partitions that we failed to boot from (the ones with
'bootfailed' attribute) and will remove this attribute. It will also
find partition with 'bootonce' attribute - this is the partition we
booted from successfully. The script will log success and remove the
attribute.
All the GPT updates we do here goes to both primary and backup GPT if
they are valid. We don't touch headers or partition tables when
checksum doesn't match.
Reviewed by: arch (Message-ID: <20100917234542.GE1902@garage.freebsd.pl>)
Obtained from: Wheel Systems Sp. z o.o. http://www.wheelsystems.com
MFC after: 2 weeks
and sys/boot/pc98/boot2, do not simply assign 'gcc' to CC, since compile
flags are sometimes passed via this variable, for example during the
build32 stage on amd64. This caused the 32-bit libobjc build on amd64
to fail.
Instead, only replace the first instance of clang (if any, including
optional path) with gcc, and leave the arguments alone.
Approved-by: rpaulo (mentor)
it possible to boot from ZFS RAIDZ for example from within VirtualBox.
The problem with VirtualBox is that its BIOS reports only one disk present.
If we choose to ignore this report, we can find all the disks available.
We can't have this work-around to be turned on by default, because some broken
BIOSes report true when it comes to number of disks, but present the same disk
multiple times.
- Change putc_func_t to use a char instead of an int for the character.
- Make functions and variables not used outside of this source file static.
- Remove unused prototypes and variables.
- The OFW read and seek methods take 3 and not 4 input arguments.
Before the change it wasn't possible and the following error was printed:
ZFS: can only boot from disk, mirror or raidz vdevs
Now if the original vdev (the one we are replacing) is still present we will
read from it, but if it is not present we won't read from the new vdev, as it
might not have enough valid data yet.
MFC after: 2 weeks
Seagate FreeAgent DockStar(tm) device. It seems to be a dumb down
version of Marvell SheevaPlug. Device tree source file could use
more tweaking, but at least it wll network boot and run FreeBSD/arm.
the file handle's size and was recently committed to
lib/libstand/nfs.c. This allows pxeboot to use NFSv3 and work
correcty for non-FreeBSD as well as FreeBSD NFS servers.
If built with OLD_NFSV2 defined, the old
code that predated this patch will be used.
Tested by: danny at cs.huji.ac.il
which also avoids NULL pointer arithmetic, as suggested by jhb. The
available space goes from 11 bytes to 7.
Reviewed by: nyan
Approved by: rpaulo (mentor)
gnu/lib/libobjc and sys/boot/i386/boot2, so it also works when using
absolute paths and/or options, as in CC="/absolute/path/clang -foo".
Approved by: rpaulo (mentor)
