Kick the device into the right mode if it comes up as a flash-disk.
Set the buffers to a sensible 1024 bytes instead of a far too small
default.
Don't attempt to change speed, baud, parity and such, the device does
not understand it.
this also can be happened if we pull the USN stick out forcibly.
Currently the ZyDAS driver uses tsleep() when it try to query a read
command to the device and it'd make a timeout if the device doesn't
response within about 1 sec.
In a case of that the USB stick is gone by hand and the driver's
scanning with changing the channel numbers, the thread which is sleeping
until a command requested is responded can be waked up after all
detaching routines finished that means the zyd softc already freed.
Tring to touch the softc freed by the wakeup thread makes a panic.
So make sure that all sleeping threads should be waken up before the
detach is completed and any other new requests to the device should be
prevented.
detaching that when the USB is pulled out forcibly during the driver is
running background scan, a page fault can be occurred even if we called
usb_rem_task() when detaching. It looks like a kind of races.
the device indicates that it wasn't able to write all the data in the
buffer out.
Ed Schouten doesn't like the idea of a panic here. I think for
production code, we need something better. For right now, while we're
trying to assess the impact of this issue, a panic is OK. So complain
to me, not him if this is hit.
from umodem and ufoma.
With these changes, umodem kinda works for me now. It certainly gets
past the "tip" bug that I found earlier where 115200 wasn't a valid
baud rate. This was "broken" in the mpsafetty commit, but in reality,
umodem was always broken.
taken from PR/121184 which was mechanically generated from similar
lists in the Linux ipaq driver. I then took the numbers we had in
usbdevs and filled in the right symbols and eliminated duplicates.
PR: 121184
The last half year I've been working on a replacement TTY layer for the
FreeBSD kernel. The new TTY layer was designed to improve the following:
- Improved driver model:
The old TTY layer has a driver model that is not abstract enough to
make it friendly to use. A good example is the output path, where the
device drivers directly access the output buffers. This means that an
in-kernel PPP implementation must always convert network buffers into
TTY buffers.
If a PPP implementation would be built on top of the new TTY layer
(still needs a hooks layer, though), it would allow the PPP
implementation to directly hand the data to the TTY driver.
- Improved hotplugging:
With the old TTY layer, it isn't entirely safe to destroy TTY's from
the system. This implementation has a two-step destructing design,
where the driver first abandons the TTY. After all threads have left
the TTY, the TTY layer calls a routine in the driver, which can be
used to free resources (unit numbers, etc).
The pts(4) driver also implements this feature, which means
posix_openpt() will now return PTY's that are created on the fly.
- Improved performance:
One of the major improvements is the per-TTY mutex, which is expected
to improve scalability when compared to the old Giant locking.
Another change is the unbuffered copying to userspace, which is both
used on TTY device nodes and PTY masters.
Upgrading should be quite straightforward. Unlike previous versions,
existing kernel configuration files do not need to be changed, except
when they reference device drivers that are listed in UPDATING.
Obtained from: //depot/projects/mpsafetty/...
Approved by: philip (ex-mentor)
Discussed: on the lists, at BSDCan, at the DevSummit
Sponsored by: Snow B.V., the Netherlands
dcons(4) fixed by: kan
corresponding USAGE should be skipped as well.
For example, below is a report desc fragment of some mouse:
COLLECTION
...
USAGE TWHEEL
FEATURE ...
...
USAGE WHEEL
INPUT ...
...
END COLLECTION
"USAGE TWHEEL" should be consumed after the FEATURE item is skipped,
otherwise, the INPUT item will be assigned to "USAGE TWHEEL" later,
other than "USAGE WHEEL".
Tested by: Grzegorz Blach
PR: usb/125941
This driver supports GW3887 based chipsets and works on
x86/powerpc/sparc64. You need upgtfw kernel module before loading
upgt(4). Please see the manpage.
Obtained from: OpenBSD
The kbd, kbdmux, ugen and uhid drivers included <sys/tty.h>, because
they needed clists, which have been moved to <sys/clist.h> some time
ago. In the MPSAFE TTY branch, <sys/tty.h> does not include
<sys/clist.h>, which means we have to teach these drivers to include
this header file directly.
Approved by: philip (mentor, implicit)
dispatched without Giant, and add NETISR_FORCEQUEUE, which allows specific
netisr handlers to always be dispatched via a queue (deferred). Mark the
usb and if_ppp netisr handlers as NETISR_FORCEQUEUE, and explicitly
acquire Giant in those handlers.
Previously, any netisr handler not marked NETISR_MPSAFE would necessarily
run deferred and with Giant acquired. This change removes Giant
scaffolding from the netisr infrastructure, but NETISR_FORCEQUEUE allows
non-MPSAFE handlers to continue to force deferred dispatch so as to avoid
lock order reversals between their acqusition of Giant and any calling
context.
It is likely we will be able to remove NETISR_FORCEQUEUE once
IFF_NEEDSGIANT is removed, as non-MPSAFE usb and if_ppp drivers will no
longer be supported.
Reviewed by: bz
MFC after: 1 month
X-MFC note: We can't remove NETISR_MPSAFE from stable/7 for KPI reasons,
but the rest can go back.
Remove the code which disables port status change interrupts for 1s
when one occured -- this makes that events get lost or delayed until
the next change.
Obtained from: NetBSD
some longstanding issues:
o pass the vap since it's now the "coin of the realm" and required
to do things like set initial tx parameters in private node
state for use prior to association
o pass the mac address as cards that maintain outboard station
tables require this to create an entry (e.g. in ibss mode)
o remove the node table reference, we only have one node table
and it's unlikely this will change so this is not needed to
find the com structure
Add support for the Apple USB Ethernet adapter.
Work around the "latch in at the first working PHY address hack",
that fails for this adapter because it returns 0xffff when reading
from lower PHY addresses. Also add more debugging printfs
Obtained from: OpenBSD
MFC After: 3 days
o correct mapping of CCK rates to PLCP; was using nonstandard Ralink
values which just happened to also be used by Zydas (so went unnoticed)
o change ieee80211_plcp2rate api to take a phy type instead of a flag
that indicates ofdm/!ofdm
o update drivers to match (restore per-driver code to map rate->PLCP)
Reviewed by: sephe, weongyo, thompsa
o add IEEE80211_C_STA capability to indicate sta mode is supported
(was previously assumed) and mark drivers as capable
o add ieee80211_opcap array to map an opmode to the equivalent capability bit
o move IEEE80211_C_OPMODE definition to where capabilities are defined so it's
clear it should be kept in sync (on future additions)
o check device capabilities in clone create before trying to create a vap;
this makes driver checks unneeded
o make error codes return on failed clone request unique
o temporarily add console printfs on clone request failures to aid in
debugging; these will move under DIAGNOSTIC or similar before release
- Limit grabbing the lock to SIOCSIFFLAGS.
- Move ieee80211_start_all() to SIOCSIFFLAGS.
- Remove SIOCSIFMEDIA as it is not useful.
- Limit ether_ioctl to only SIOCGIFADDR. SIOCSIFADDR and SIOCSIFMTU have no
affect as there is no input/output path in the vap parent. The vap code
will handle the reinit of the mac address changes.
- Split off ndis_ioctl_80211 as it was getting too different to wired devices.
This fixes a copyout while locked and a lock recursion.
Reviewed by: sam
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
I've taken a slightly different approach than is used with the ICH8 controllers
in that each controller is not identified individually (eg USB A, USB B, etc).
Instead I've given then same description to each one even though the device ID
differs. This can easily be changed if desired, or ICH8 (and any others using
that approach) can be made to work as this does.
work on architectures with a write-back cache as the PIO writes end up
in the cache which the sync(BUS_DMASYNC_POSTREAD) in usb_transfer_complete
then discards; compensate in the xfer methods that do PIO by pushing the
writes out of the cache before usb_transfer_complete is called.
This fixes USB on xscale and likely other places.
Sponsored by: hobnob
Reviewed by: cognet, imp
MFC after: 1 month
all uses) involve a read but usbd_start_transfer only does a PREWRITE; change
this to BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE as I'm not sure if any
users do write+read.
Reviewed by: cognet, imp
MFC after: 1 month
monitor mode. This solves a problem that sometimes mangled frames
are passed.
Submitted by: Werner Backes <werner_at_bit-1.de>
Tested by: Werner Backes <werner_at_bit-1.de>
PR: kern/121608
Approved by: thompsa (mentor)
hangs (one at boot, one at shutdown) in recent machines. First, only try
to take ownership of the EHCI controller if the BIOS currently owns the
controller. On a HP DL160 G5, the machine hangs when we try to take
ownership. Second, don't bother trying to give up ownership of the
controller during shutdown. It's not strictly required and a Dell DCS S29
hangs on shutdown after the config write.
Both of these changes match the behavior of the Linux EHCI driver. I also
think both of these hangs are caused by bugs in the BIOS' SMM handler
causing it to get stuck in an infinite loop in SMM.
MFC after: 1 week
accept a mouse using the boot subclass. Instead, restore the original
hid_is_collection() test and fallback to testing the interface class,
subclass, and protocol if that fails.
MFC after: 1 week
PR: usb/118670
than rely on the lockmgr support [1]:
* bump the waiters only if the interlock is held
* let brelvp() return the waiters count
* rely on brelvp() instead than BUF_LOCKWAITERS() in order to check
for the waiters number
- Remove a namespace pollution introduced recently with lockmgr.h
including lock.h by including lock.h directly in the consumers and
making it mandatory for using lockmgr.
- Modify flags accepted by lockinit():
* introduce LK_NOPROFILE which disables lock profiling for the
specified lockmgr
* introduce LK_QUIET which disables ktr tracing for the specified
lockmgr [2]
* disallow LK_SLEEPFAIL and LK_NOWAIT to be passed there so that it
can only be used on a per-instance basis
- Remove BUF_LOCKWAITERS() and lockwaiters() as they are no longer
used
This patch breaks KPI so __FreBSD_version will be bumped and manpages
updated by further commits. Additively, 'struct buf' changes results in
a disturbed ABI also.
[2] Really, currently there is no ktr tracing in the lockmgr, but it
will be added soon.
[1] Submitted by: kib
Tested by: pho, Andrea Barberio <insomniac at slackware dot it>
With write-allocate cache we get into the following scenario:
1. data has been updated in the memory by the USB HC, but
2. D-cache holds an un-flushed value of it
3. when affected cache line is being replaced, the old (un-flushed) value is
flushed and overwrites the newly arrived
This is possible due to how write-allocate works with virtual caches (ARM for
example).
In case of USB transfers it leads to fatal tags discrepancies in umass(4)
operation, which look like the following:
umass0: Invalid CSW: tag 1 should be 2
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 3
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 4
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 5
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 6
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): error 5
(probe0:umass-sim0:0:0:0): Retries Exausted
To eliminate this, a BUS_DMASYNC_PREREAD sync operation is required in
usbd_start_transfer().
Credits for nailing this down go to Grzegorz Bernacki gjb AT semihalf DOT com.
Reviewed by: imp
Approved by: cognet (mentor)
- Include lock.h in lockmgr.h as nested header in order to safely use
LOCK_FILE and LOCK_LINE. As long as this code will be replaced soon
we can tollerate for a while this namespace pollution even if the real
fix would be to let lockmgr() depend by lock.h as a separate header.
- Remove the "thread" argument from the lockmgr() function as it is
always curthread now
- Axe lockcount() function as it is no longer used
- Axe LOCKMGR_ASSERT() as it is bogus really and no currently used.
Hopefully this will be soonly replaced by something suitable for it.
- Remove the prototype for dumplockinfo() as the function is no longer
present
Addictionally:
- Introduce a KASSERT() in lockstatus() in order to let it accept only
curthread or NULL as they should only be passed
- Do a little bit of style(9) cleanup on lockmgr.h
KPI results heavilly broken by this change, so manpages and
FreeBSD_version will be modified accordingly by further commits.
Tested by: matteo
Now, lockmgr() function can only be called passing curthread and the
KASSERT() is upgraded according with this.
In order to support on-the-fly owner switching, the new function
lockmgr_disown() has been introduced and gets used in BUF_KERNPROC().
KPI, so, results changed and FreeBSD version will be bumped soon.
Differently from previous code, we assume idle thread cannot try to
acquire the lockmgr as it cannot sleep, so loose the relative check[1]
in BUF_KERNPROC().
Tested by: kris
[1] kib asked for a KASSERT in the lockmgr_disown() about this
condition, but after thinking at it, as this is a well known general
rule, I found it not really necessary.
implemented with macros. This patch improves code readability. Reasoning
behind kbdd_* is a "keyboard discipline".
List of macros is supposed to be complete--all methods of keyboard_switch
should have their respective macros from now on.
Functionally, this code should be no-op. My intention is to leave current
behaviour of code as is.
Glanced at by: rwatson
Reviewed by: emax, marcel
Approved by: cognet
If a mouse has both a wheel and a Z direction we report both.
XXX Due to tradition the wheel is reported as the Z direction (and the Z
direction as W).
Now Apple's Mighty Mouse is fully supported, except the X11 mouse driver
doesn't know what to do with the new coordinate.
MFC after: 3 months
Approved by: njl (mentor), imp
and update the rx code to handle multiple frames in a single usb
transfer. AX772 parts (at least) exhibit many input errors when
operated with a 2K rx buffer and no errors w/ a 4K rx buffer (it's
unclear what the cause of the errors is for 2K so this may just be
covering up the real issue). Larger rx buffer sizes show no
significant performance improvement for AX772. Bypassing the common
buffer management routines also eliminates an extra context switch
on every packet which noticeably improves performance (TCP netperf
rx goes from 45 Mb/s to 85 MB/s).
Submitted by: "J.R. Oldroyd" <fbsd@opal.com>
Reviewed by: imp
Obtained from: openbsd (partly)
MFC after: 3 weeks
- Patch registers CR47 and CR157 on devices that require it.
- Fix power calibration setting on ZD1211B.
Obtained from: OpenBSD
- Fix multicast transfer by properly reprogram multicast global
hash table, which in turns fix promiscuous mode and IPv6
autoconfiguration / local networking.
Reviewed by: sam, Weongyo Jeong
Tested using: Aztech WL230 , Belkin F5D7050, Unicorn WL-54G,
3COM 3CRUSB10075
MFC after: 1 week
Allocate space in keyboard state structure instead to prevent random byte
from possibly overwritten stack location frombeing shoved into USB device
when transfer actually takes place.
This fixes at least one instance of LEDs not working with USB keyboards.
reset problem when we reboot the system with the zyd device inserted.
Submitted by: Weongyo Jeong
Reported by: Ted Lindgreen (ted@tednet.nl)
MFC after: 1 week
to kproc_xxx as they actually make whole processes.
Thos makes way for us to add REAL kthread_create() and friends
that actually make theads. it turns out that most of these
calls actually end up being moved back to the thread version
when it's added. but we need to make this cosmetic change first.
I'd LOVE to do this rename in 7.0 so that we can eventually MFC the
new kthread_xxx() calls.
ukbd_poll to mark this keyboard instance as polling before calling
usbd_set_polling at USB level. usbd_set_polling runs softintr before
returning, stealing our input and making consequent polling getchar
kind of pointless.
This allows USB keyboards to coexist peacefully with serial console in DDB
and other contexts where polling is used.
MFC after: 1 week
properly due to the shortage of the RX buffer size. In a case of zyd
devices, up to 3 frames can be combined in an USB transaction. So, RX
buffer should be at least ((MCLBYTES + extra structs) * 3)
Submitted by: Weongyo Jeong <weongyo.jeong@gmail.com>
MFC after: 3 days
which is ukbd0. Specifically, the keyboard driver structures for ukbd0
are not allocated/freed but are statically allocated via a persistent
global variable. There is some additional magic for the ukbd0 such that
if the keyboard is marked as probed in this global variable, then we
don't check to see if the device_t we are probing has an interface.
This causes a problem if an attach of ukbd0 fails without fulling clearing
the state in the global variable. Specifically, if the keyboard fails to
initialize in init_keyboard() or kbd_register(), then the keyboard will
still be marked as probed. The USB layer will then try to offer the
"generic" version of the USB keyboard device (as opposed to the
per-interface sub-devices) and the ukbd(4) driver will see that the
keyboard is marked probe and will skip the "is this a per-interface device"
check. Later in ukbd_attach() it panics because it tries to dereference
the interface pointer which is NULL.
The fix is to clear the flags in the persistent keyboard data for ukbd0
when init_keyboard() or kbd_register() fail.
MFC after: 1 week
Reviewed by: imp
with all functions supported. This is done adding usb device IDs
to the table of recognised devices (because there is no standard
'scanner' class, so no other way to recognise them), and with
a small change to the uscanner attach routine that prevents
reconfiguring the whole USB device while we are dealing only with
one of its USB interfaces.
The latter part has been suggested by Steinar Hamre in
http://www.freebsd.org/cgi/query-pr.cgi?pr=107665 , i have
only added a bit of explaination to the code.
I have personally tried this on the Epson DX-5050 and DX-6000
devices (on the US market they have different names, CX-something).
I have good reasons to think that, possibly with the mere addition
of more USB ids to the table in uscanner.c, this should work with
all Epson multifunction devices in that family (from DX-3800 to
DX-7000 - these units are in the 50-120$ price range).
More details on related topics (SANE configuration, OCR, etc.)
at http://info.iet.unipi.it/~luigi/FreeBSD/dx5050.html
Manpage updates coming soon.
Approved by: re, imp
MFC after: 3 days
controller if it's sole child device has the "usb" device class.
Previously ehci(4) would think that PCI-ISA bridges on the same slot
(such as in some Intel ICHs) were "neighbors" resulting in spurious
warnings about neighbor count mismatches.
- Fix a memory leak when looking for neighbors.
MFC after: 1 week
Approved by: re (kensmith)
Tested by: phk
o add driver callback to handle notification of beacon changes;
this is required for devices that manage beacon frames themselves
(devices must override the default handler which does nothing)
o move beacon update-related flags from ieee80211com to the beacon
offsets storage (or handle however a driver wants)
o expand beacon offsets structure with members needed for 11h/dfs
and appie's
o change calling convention for ieee80211_beacon_alloc and
ieee80211_beacon_update
o add overlapping bss support for 11g; requires driver to pass
beacon frames from overlapping bss up to net80211 which is not
presently done by any driver
o move HT beacon contents update to a routine in the HT code area
Reviewed by: avatar, thompsa, sephe
Approved by: re (blanket wireless)
that can lead to a panic when the stick is yanked.
- make sure that zyd_attach() returns 0 or errno.
Submitted by: Weongyo Jeong <weongyo.jeong@gmail.com>
Reported by: Ted Lindgreen <ted@tednet.nl>
Reviewed by: sam
Approved by: re (blanket wireless)
o update ic_lastdata to reflect time of last outbound frame
o outbound traffic must preempt/cancel bg scanning to avoid delays
This stuff was somehow missed in the initial import.
Reviewed by: thompsa, avatar, sephe (earlier version)
Approved by: re (blanket wireless)
ZD1211/ZD1211B USB IEEE 802.11b/g wireless network devices. Not (yet)
connected to the build process (next batch of commits once I've looped
the current back back).
Submitted by: Weongyo Jeong
Reviewed by: sam@
Approved by: re@
differ in their details with calls to a new function, ehci_hcreset(),
that performs the reset.
The original sequences either had no delay or a 1ms delay between
telling the controller to stop and asserting the controller reset
bit. One instance of the original reset sequence waited for the
controller to indicate that its reset was complete before continuing,
but the other two immediately let the subsequent code execute. The
latter is a problem on some hardware, because a read of the HCCPARAMS
register returns an incorrect value while the reset is in progress,
which triggers an infinite loop in ehci_pci_givecontroller(), which
hangs the system on shutdown.
The reset sequence in ehci_hcreset() starts with the most complete
instance from the original code, which contains a loop to wait for
the controller to indicate that its reset is complete. This appears
to be the correct thing to do according to "Enhanced Host Controller
Interface Specification for Universal Serial Bus" revision 1.0,
section 2.3.1. Add another loop to wait for the controller to
indicate that it has stopped before setting the HCRESET bit. This
is required by the section 2.3.1 in the specification, which says
that setting HCRESET before the controller has halted "will result
in undefined behaviour".
Reviewed by: imp (previous patch version without the extra wait loop)
Tested by: se (previous patch version without the extra wait loop)
Approved by: re (bmah)
MFC after: 1 week
to repeat if you had more than two keys down at any given time (which
happened to me all the time with emacs).
This is taken from PR 110681, although what URATAN Shigenobu describes
there is different than the pathology that I have been seeing. I'm
seeing this only in X, while he sees it on his console, yet I think
the two problems are related. I've also reworked the patch slightly
to conform to the coding standards of adjacent code.
It is unclear to me if this merely masks the maddening bug that I have
seen, or if this is a real fix. I typically see the problem when I'm
typing fast in emacs and using lots of motion keys (meta and control).
In either case, my workstation at work again is finally useful with
this patch.
PR: 110681
Submitted by: URATAN Shigenobu
Approved by: re (blanket)
the protocol to be report on each open, but ignore any errors as set
protocol for mice that don't implement the boot protocol can generate
an error. Evidentally, the Gyration GyroPoint RF Technology Receiver
(Gyration Ultra Cordless) device has this problem.
Submitted by: Eugene M. Kim
PR: 106565
Approved by: re (blanket)
do the heavy lifting of the 'mii_tick' function, rue was left behind.
Implement this in a naive way. Reports from the field show this makes
the driver functional with some locking issues, as opposed to an
instant panic. Those will be addressed in a later version of the
driver.
Approved by: re@ (bmah)
Sort NETGEAR list per convention.
Swap QUALCOMM and QUALCOMM2.
Add a few vendor products.
no md5 changes with this file (except when USBVERBOSE is enabled)
Approved by: re@ (blanket)
in. These are exclusively in the name of the company for this round.
No new devices have been added, but the MITEL entry has been
eliminated because nothing uses it. You won't see any difference
unless you have USBVERBOSE defined for the kernel.
Approved by: re@ (blanket)
o Adonics Cable 205
o Aiptek PocketCAM 3Mega
o Belkin USB2SCSI
o Casio QV DigiCam
o CCYU EasyDisk ED1064
o Desknote UCR-61S2B
o Epson Stylus Photo 875DC Card Reader
o Epson Stylus Photo 895 Card Reader
o Feiya 5-in-1 Card Reader
o Hitachi Dvd-CAM DZ-MV100A Camcorder
o HP CD-WRiter+ CD-4e
o Insystem Storage Adapter v2
o Kyocera Finecam S3x
o Kyocera Finecam S4
o Kyocera Finecam S5
o Kyocera Finecam L3
o Lexar USB CF Reader
o MindAtWork Digital Wallet
o Minolta Dimage F300
o Minolta Dimage E223
o Minsumi USB Fdd
o Netac USB-CF-Card
o NetChip USB Clik! 40
o Onspec MDCFE-B USB CF Reader
o Onspec SIIG/Datafab Memory Stick + CF Reader/Writer
o Onspec Datafab-based Reader
o Onspec PNY/Datafab CF+SM Reader
o Onspec SimpleTech/Datafab CF+SM Reader
o Onspec MDSM-b Reader
o Onspec USB To CF + SM Combo (LC1)
o Onspec ImageMate SDDR55
o Panasonic LS-120 Camera
o Samsung Techwin Digimax 410
o Shuttle eUSB SmartMedia / CompactFlash Adapter
o Skanhex MD 7425 Camera
o Skanhex SX 520z Camera
o Sony Memorystick NW-MS7
o Sony Portable USB Hardrive V2
o Sony Memorystick PEG N760c
o Sony Memorystick MSC-U03
o TREK/IBM USB memory key
o Trumpion T33520 USB Flash Card Controller
o Trumpion MP3 Player
o Vivtar Vivicam 35Xx
o WinMaxGroup USB Flash Disk 64M-C
o Zoran Digital Camera EX-20 DSC
and maybe a few others...
Submitted by: Vaidas Damosevicius and flz
PR: 79893
Reviewed by: njl, flz
Approved by: re (blanket)
(1) Add size parameter to usbd_get_string()
(2) Properly limit speed when a full speed hub is plugged into a high
speed hub.
Submitted by: Hans Petter Selasky
PR: 80773, 79725
Approved by: re@ (kensmith)
yet supported by this driver. Support will be committed soon, or a
filter on all the 'newer' devices will be installed before the
release.
Approved by: re@ (blanket)
Obtained from: NetBSD, OpenBSD
Small Furry Animals by: Pink Floyd
the command. Make UFI devices return 'success' when asked to do a
SYNC_CACHE. There's no support for write caching in the UFI spec, so
this is the most appropriate action to undertake.
Reviewed by: scottl
Approved by: re@ (blanket)
Hellmuth with some refinements by myself and flz@. It works for me
with my non-MS mice, so nothing should be broken by it.
Submitted by: Hellmuth Michaelis
PR: 90162
Approved by: re (blanket)
pr, the submitter says:
Found this while running freebsd as guest in qemu with -usb
parameter. The patch implements the missing dynamic size based on
number of ports a hub has.
Submitted by: Lonnie Mendez
PR: 94946
Approved by: re@ (blanket)
patch that converts ms to ticks was used. Another PR states that a
return code of 0 is the right one for libusb.
Submitted by: Lonnie Mendez
PR: 94311
Approved by: re (blanket)
adequate. Increase them to 1k. The referenced PR made this a sysctl,
but that seems like overkill to me. The difference between 320 and
2048 bytes in modern systems, even embedded ones, seems to be in the
noise to be worth the extra hair to make it settable.
PR: 74609
Submitted by: Divacky Roman
Approved by: re (blanket)
applied to, but I'd think both), honor the timeout that's been set.
Return 0 bytes to be consistant with what libusb expects. By default,
the timeout will be zero, so only applications that change the default
will see a change. The patch only seems to apply to the interrupt end
points, but it should also apply to isochronous endpoints as well.
Submitted by: Maurice Castro
PR: 110122
Approved by: re (blanket)
of the file numerically for vendors and then each product numerically
by vendor (with all the foo2's sorting after the foo's). Someday, all
the usbdevs will be merged, I hope, but until then, we have these
mega-merges.
This also finishes the LINKSYS4 -> CISCOLINKSYS rename.
Approved by: re@ (blanket)
around an output freezing problem (see the CVS log for details). This
is the same approach that sio takes to solve that problem. However,
ucom has a problem that sio doesn't have.
Consider the case where output is pending, and the device is closed.
ttyclose calls tt_close (which indirects to ucomclose) and then calls
ttyflush which calls tt_stop (which indirects to ucomstop). Since
ucomclose removed all the usb transfer points, sc_oxfer will be NULL
when ucomstop calls ucomstart. This results in a null pointer
dereference.
Since calling ucomstart in ucomstart solves other problems, we need to
work with this calling sequence. The easiest way to do that is to
bail early if sc_oxfer is NULL.
Kazuaki ODA-san came up with this patch, and filed a PR. I had seen
this bug at work and this patch does seem to solve it. He had no idea
why it worked, but knew that either this patch, or backing out ucom.c
1.56 fixed his panic. I just did the legwork of chasing down the code
paths that would cause this, and added a comment. This is obscure
enough to warrant a comment, I think.
Submitted by: Kazuaki ODA-san
PR: 113964
Approved by: re (bmah)
o Consistently use device_foo_t and bus_foo_t for functions implementing
device_foo and bus_foo respectively. Adjust those routines that were wrong
(we should do this throughout the tree).
o make all the modules depend on usb. Otherwise these modules won't
load.
o ucycom doesn't need usb_port.h
o Minor unifdefing
o uhub, umass, ums, urio, uscanner conversion complete.
o ukbd: Remove the NO_SET_PROTO quirk (fixes a PR 77940). NetBSD removed
their check and setting the proto a long time ago.
o umodem panic fixed. UQ_ASSUME_CM_OVER_DATA quirk removed because I've never
seen a umodem that needed this rejection for proection (this gets rid of
~20% of the quirks).
Approved by: re@ (kensmith)
PR: 77940
Older drivers that do not wish to convert to the native API (which
will work with both 6.x and 7.x) can simply include
<dev/usb/usb_port.h>. Drivers in the tree shouldn't these macros,
unless they actually work on other OSes and are actively maintained.
Approved by: re@
Remove device_t dv, since it is no longer needed.
Add sizeof(device_t) to replace sizeof dv.
Change device_detach(dev) to device_detach(dev->subdevs[i]) since the type
of dev isn't right! Not sure when this was introduced, but it likely would
lead to a crash on disconnect.
MFC After: 1 week
now takes a device_t to be the parent of the bus that is being created.
Most SIMs have been updated with a reasonable argument, but a few exceptions
just pass NULL for now. This argument isn't used yet and the newbus
integration likely won't be ready until after 7.0-RELEASE.
Also, remove usb_malloc_type: it was unused.
Remove METHODS_NONE: it was unused.
Move include of opt_usb.h from usb_port.h to usb.h, since usb_port.h is
going away (there will be a usb_compat.h for out-of-tree drivers that want it).
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
error doing so. It seems an increasing number of phones have this
quirk, and we're not keeping up. There appears to be nothing bad that
happens for non-quirked phones.
Minor cleanups:
o prefer device_printf over printf
o kill devinfo stuff
o minor other preening.
need to do it at all anymore. Remove it from here. Expand
USB_ATTACH_SETUP inline now that it is one line and we're moving away
from the compat macros. Remove some bzero calls that turn out not be
be necessary.
what we print, don't print it anymore. And don't compute it anymore.
And don't malloc/free memory for it anymore. While I'm here, prefer
device_printf where appropriate.
sysctl_handle_int is not sizeof the int type you want to export.
The type must always be an int or an unsigned int.
Remove the instances where a sizeof(variable) is passed to stop
people accidently cut and pasting these examples.
In a few places this was sysctl_handle_int was being used on 64 bit
types, which would truncate the value to be exported. In these
cases use sysctl_handle_quad to export them and change the format
to Q so that sysctl(1) can still print them.
OpenBSD's if_ral.c.
I didn't make the LINKSYS4 -> CISCOLINKSYS name change, nor did I
include the RALINK RT2573 that's supported by the rum(4) driver. I
didn't merge any code changes either.
supports software encrypt/decrypt.
The nuked code itself is quite problematic, as pointed out by sam@ ---
wk->wk_keyix should be replaced by the loop count.
Tested with WEP/TKIP/CCMP/no-protection.
Approved by: sam@ (mentor)
Noticed by: Hans Petter Selasky <hselasky@c2i.net>
- For ural(4):
o Fix node leakage in ural_start(), if ural_tx_mgt() fails.
o Fix mbuf leakage in ural_tx_{mgt,data}(), if usbd_transfer() fails.
o In ural_tx_{mgt,data}(), set ural_tx_data.{m,ni} to NULL, if
usbd_transfer() fails, so they will not be freed again in ural_stop().
Approved by: sam (mentor)
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant and operate as
usual. RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.
The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.
obtaining and releasing shared and exclusive locks. The algorithms for
manipulating the lock cookie are very similar to that rwlocks. This patch
also adds support for exclusive locks using the same algorithm as mutexes.
A new sx_init_flags() function has been added so that optional flags can be
specified to alter a given locks behavior. The flags include SX_DUPOK,
SX_NOWITNESS, SX_NOPROFILE, and SX_QUITE which are all identical in nature
to the similar flags for mutexes.
Adaptive spinning on select locks may be enabled by enabling the
ADAPTIVE_SX kernel option. Only locks initialized with the SX_ADAPTIVESPIN
flag via sx_init_flags() will adaptively spin.
The common cases for sx_slock(), sx_sunlock(), sx_xlock(), and sx_xunlock()
are now performed inline in non-debug kernels. As a result, <sys/sx.h> now
requires <sys/lock.h> to be included prior to <sys/sx.h>.
The new kernel option SX_NOINLINE can be used to disable the aforementioned
inlining in non-debug kernels.
The size of struct sx has changed, so the kernel ABI is probably greatly
disturbed.
MFC after: 1 month
Submitted by: attilio
Tested by: kris, pjd
to a READ_CAPACITY request rather than the maximum sector (off by one
problem). This causes a huge cascade of errors as the geom tasting
code tries to read the last sector (which isn't really there in the
face of this error). automated tools that manipulate disk labels and
such also have issues.
Create a new quirk READ_CAPACITY_OFFBY1 and add a quirk for the
SanDISK ImageMate that I have that suffers from this problem (the
SDDR-31). It intercepts the READ_CAPACITY response and adjusts it
from number of sectors to max sector for devices with this quirk.
Reading the Linux source suggests that there are a host of
other devices with this issue, including iPods and some popular
cameras. I've not added quirks for them, since I don't have the
devices in front of me to test.
The patch from the PR was a little outdated w/regards to the
Vodafone vendor string.
PR: kern/106033
Submitted by: Volker Werth <volker_AT_vwsoft.com>
MFC in: 3 days
description here. The fix in the PR isn't necessary at all for memory
leaks, but we weren't setting the device description.
While I'm here, remove some of the obfuscating macros in attach.
PR: 108719
PR/108719, but there's a simpler fix: free it after it is used, and
then get rid of the redundant frees this causes. Other leaks in this
PR not yet fixed.
While I'm here, remove NetBSD/OpenBSD code and some of the portability
#defines that were getting in the way of understanding this code. The
devinfo bug was harder to spot because one needed to know that
device_set_desc_copy() was used inside of one of them (one that didn't
take an argument!).
Prefer device_printf(sc->sc_dev, "...") to printf("%s:...",
device_get_nameunit(sc->sc_dev)). This saves almost 300 bytes.
PR: 108719
Submitted by: Antoine Brodin
sparc64 GENERIC and the sound device drivers known working on sparc64
to use bus_get_dma_tag() to obtain the parent DMA tag so we can get rid
of the sparc64_root_dma_tag kludge eventually. Except for ath(4), sk(4),
stge(4) and ti(4) these changes are runtime tested (unless I booted up
the wrong kernels again...).
total size of all input reports is < 6.
PR: usb/106435
Submitted by: Eygene Ryabinkin <rea-fbsd@codelabs.ru>
Approved by: emax (mentor)
MFC after: 3 days
not needed if the proper ordering is done in attach and shutdown.
Remove usage of if_timer/watchdog and roll my own by piggybacking
off the tick() function.
Use the new usb system to allocate task queues instead of using
the system wide thread for taskqueues.
for usb. I hope that this will eventually be used for generic devices
that need full fledged blocking threads for event processing.
Create a taskqueue:
void usb_ether_task_init(device_t, int, struct usb_taskqueue *);
Enqueue a task:
void usb_ether_task_enqueue(struct usb_taskqueue *, struct task *);
Wait for all tasks queued to complete:
void usb_ether_task_drain(struct usb_taskqueue *, struct task *);
Destroy the taskqueue:
void usb_ether_task_destroy(struct usb_taskqueue *);
start working with third party usb modules, where sometimes it
is not easy to set the inclusion order so that there are no multiple
inclusions, yet you want to compile with high WARNS levels).
I am not sure if there is a standard for having a leading and/or trailing _
in the macro name, the usb code seems to use both.
There are still several unprotected headers here so it might be useful
to do the same thing on other files as well as the need arises.
MFC After: 3 days
The problem was that I was acquiring the driver sx lock and then waiting
for a taskqueue to drain, however the taskqueue itself would try to
acquire the lock as well leading to a deadlock.
To fix the problem roll my own exclusive lock that allows for lock
cancellation. This is a normal exclusive lock, however if someone
marks it as "dead" then all waiters who request an error return will
get back an error instead of continuing to wait for the lock.
In this particular case, the shutdown and detach functions kill the
lock while the async task thread tries to acquire the lock but will
abort if the lock returns an error.
The other option was to drop the driver lock mid-detach and mid-shutdown,
mid-detach was a ok, however mid-shutdown was not.
While I'm here, fix a bug in what appears to be the mii link status
word in the softc going out to lunch. Explicitly set the status
word to 1 after initializing the mii. This would result in an interface
that would never respond to "if_start" requests as the mii interface
would always look down.
aue_tick calls several synchronous usb functions from a timeout(9),
this is very broken since a timeout(9) is run as an interrupt
and the usb functions tsleep.
A stopgap fix is to schedule a taskqueue task from the timeout
and defer work to that taskqueue task.
an URQ_REQUEST when DMA segments are passed to usbd_start_transfer();
when the request doesn't include the optional data buffer the size of
the transfer (xfer->length) is 0, in which case usbd_transfer() won't
create a DMA map but call usbd_start_transfer() with no DMA segments.
With the previous change this could result in the bus_dmamap_sync()
implementation dereferencing the NULL-pointer passed as the DMA map
argument.
While at it fix what appears to be a typo in usbd_start_transfer();
in order to determine wheter usbd_start_transfer() was called with
DMA segments check whether the number of segments is > 0 rather than
the pointer to them being > 0.
OK'ed by: imp
I have been debugging the usb problems some more. Your were
right in your assumption (thanks for the pointer) about lack
of calls to bus_dmamap_sync(). In usbdi.c bus_dmamap_sync()
does get used for transfers that move data from PC to USB and
it is used for transfers that move data from USB to PC. But
someone forgot that control transfers consist of possibly two
data chunks : the request itself and optionally a buffer of
data that should be transfered to or from the USB device. On
requests to the control endpoint without additional data
bus_dmamap_sync() didn't get called. For some reason my first
tests with umass worked (due to enough cache poisening I
guess). The attached patch adds a call to bus_dmamap_sync()
to usbdi.c and now all devices I have tried work out of the
box. I have successfully transfered large files using the
if_axe driver and I have mounted several different umass
devices.
submitted by: Daan Vreeken
sponsored by: Vitsch Electronics
reviewed by: cognet@
the CAM_NEW_TRAN_CODE that has been in the tree for some years now.
This first step consists solely of adding to or correcting
CAM_NEW_TRAN_CODE pieces in the kernel source tree such
that a both a GENERIC (at least on i386) and a LINT build
with CAM_NEW_TRAN_CODE as an option will compile correctly
and run (at least with some the h/w I have).
After a short settle time, the other pieces (making
CAM_NEW_TRAN_CODE the default and updating libcam
and camcontrol) will be brought in.
This will be an incompatible change in that the size of structures
related to XPT_PATH_INQ and XPT_{GET,SET}_TRAN_SETTINGS change
in both size and content. However, basic system operation and
basic system utilities work well enough with this change.
Reviewed by: freebsd-scsi and specific stakeholders
: revision 1.27
: date: 2000/05/28 12:43:24; author: ache; state: Exp; lines: +3 -2
: Manipulate with AltGR Led (really CapsLock Led) only in K_XLATE mode, because
: all other modes not set ALKED flag and it means that CapsLock always turned
: off for them.
: Real bug example is X11 which never turn on CapsLock with Russian keyboard.
:
: PR: 18651
: Submitted by: "Mike E. Matsnev" <mike@po.cs.msu.su>
MFC after: 3 days
tasks. Since the host controllers rely on tasks to process transfer
timeouts, if a synchronous transfer from a driver was invoked from
a task and timed out, it would never complete because the single
task thread was stuck performing the synchronous transfer so couldn't
process the timeout.
This affected the axe, udav and ural drivers.
Problem hardware provided by: guido
- Add entries in the uscanner.4 man page (along with missing 3500).
PR: usb/100957 [1], usb/100992 [2]
Submitted by: Jim Teresco <terescoj@teresco.org> [1],
Walter C. Pelissero <walter.pelissero@iesy.net> [2]
MFC after: 3 days
close and re-open the default pipe instead of relying on the host
controller driver to notice the changes. Remove the unreliable code
that attempted to update these fields while the pipe was active.
This fixes a case where the hardware could cache and continue to
use the old address, resulting in a "getting first desc failed"
error.
PR: usb/103167
The parallel LINT build sometimes broke if kernel-depend wasn't
fast enough in generating ukbdmap.h. If someone thinks this
option would still be useful for the module, a proper fix is
to add the code generating ukbdmap.h into modules/ukbd/Makefile
and backing this change out.
ioctls passing integer arguments should use the _IOWINT() macro.
This fixes a lot of ioctl's not working on sparc64, most notable
being keyboard/syscons ioctls.
Full ABI compatibility is provided, with the bonus of fixing the
handling of old ioctls on sparc64.
Reviewed by: bde (with contributions)
Tested by: emax, marius
MFC after: 1 week
s/device_ptr_t/device_t/g
No md5 changes in the .o's
# Note to the md5 tracking club: $FreeBSD$ changes md5 after every commit
# so you need to checkout -kk to get $FreeBSD$ instead of the actual value
# of the keyword.
required by arches like sparc64 (not yet implemented) and sun4v where there
are seperate IOMMU's for each PCI bus... For all other arches, it will
end up returning NULL, which makes it a no-op...
Convert a few drivers (the ones we've been working w/ on sun4v) to the
new convection... Eventually all drivers will need to replace the parent
tag of NULL, w/ bus_get_dma_tag(dev), though dev is usually different for
each driver, and will require hand inspection...
Reviewed by: scottl (earlier version)
This enables the scanner function on these devices to be detected
and probed by uscanner(4), but only when ulpt is not loaded.
PR: usb/92462
Submitted by: Friedrich Volkmann
MFC after: 30 days
is never taken since there aren't any 802.11a ural(4) sticks available
on the market.
PR: kern/99676
Submitted by: KIYOHARA Takashi
Reviewed by: damien
MFC after: 1 week
- Curitel PC5740 Wireless Modem (Verizon's PCMCIA card)
- Sierra MC5720 Wireless Modem (Built in to Thinkpad X60s)
The scanner in the PR is already supported.
PR: 98908
Submitted by: Michael Collette <metrol@metrol.net>
blinks by default. When the operating system (read: normally an Xbox
360) initializes the gamepad, the LED stops blinking.
Change our uhid code to do the same.
PR: 97169
Submitted by: Ed Schouten <ed@fxq.nl>
device went away while open or if you tried to change the config
number while devices were open. Based on the patch from the PR with
a number of changes as discussed with the submitter.
PR: usb/97271
Submitted by: Anish Mistry
axe_cmd() calls. Without this the device can get confused if multiple
threads attempt these operations concurrently. The problem was
easily reproducible by running "ifconfig axe0" in a loop because
eventually it would conflict with axe_tick_task().
A similar approach is probably required in all USB ethernet drivers.
(1) bpf peer attaches to interface netif0
(2) Packet is received by netif0
(3) ifp->if_bpf pointer is checked and handed off to bpf
(4) bpf peer detaches from netif0 resulting in ifp->if_bpf being
initialized to NULL.
(5) ifp->if_bpf is dereferenced by bpf machinery
(6) Kaboom
This race condition likely explains the various different kernel panics
reported around sending SIGINT to tcpdump or dhclient processes. But really
this race can result in kernel panics anywhere you have frequent bpf attach
and detach operations with high packet per second load.
Summary of changes:
- Remove the bpf interface's "driverp" member
- When we attach bpf interfaces, we now set the ifp->if_bpf member to the
bpf interface structure. Once this is done, ifp->if_bpf should never be
NULL. [1]
- Introduce bpf_peers_present function, an inline operation which will do
a lockless read bpf peer list associated with the interface. It should
be noted that the bpf code will pickup the bpf_interface lock before adding
or removing bpf peers. This should serialize the access to the bpf descriptor
list, removing the race.
- Expose the bpf_if structure in bpf.h so that the bpf_peers_present function
can use it. This also removes the struct bpf_if; hack that was there.
- Adjust all consumers of the raw if_bpf structure to use bpf_peers_present
Now what happens is:
(1) Packet is received by netif0
(2) Check to see if bpf descriptor list is empty
(3) Pickup the bpf interface lock
(4) Hand packet off to process
From the attach/detach side:
(1) Pickup the bpf interface lock
(2) Add/remove from bpf descriptor list
Now that we are storing the bpf interface structure with the ifnet, there is
is no need to walk the bpf interface list to locate the correct bpf interface.
We now simply look up the interface, and initialize the pointer. This has a
nice side effect of changing a bpf interface attach operation from O(N) (where
N is the number of bpf interfaces), to O(1).
[1] From now on, we can no longer check ifp->if_bpf to tell us whether or
not we have any bpf peers that might be interested in receiving packets.
In collaboration with: sam@
MFC after: 1 month
USBD_FORCE_SHORT_XFER to ensure that we actually build and execute
a transfer. This means that the various alloc_sqtd_chain functions
will always construct a transfer, so it is safe to modify the
allocated descriptors on return. Previously there were cases where
a zero length transfer would cause a NULL dereference.
Reported by: bp
host controllers to avoid the need to allocate any multi-page
physically contiguous memory blocks. This makes it possible to use
USB devices reliably on low-memory systems or when memory is too
fragmented for contiguous allocations to succeed.
The USB subsystem now uses bus_dmamap_load() directly on the buffers
supplied by USB peripheral drivers, so this also avoids having to
copy data back and forth before and after transfers. The ehci and
ohci controllers support scatter/gather as long as the buffer is
contiguous in the virtual address space. For uhci the hardware
cannot handle a physical address discontinuity within a USB packet,
so it is necessary to copy small memory fragments at times.
EHCI spec for linking in new qTDs into an asynchronous QH. This
requires that there is a qTD marked as not active and not halted
at the start of the QH's list, and the hardware will know to re-fetch
the qTD on each pass rather than just looking at the overlay qTD:
"The host controller must be able to advance the queue from the
Fetch QH state in order to avoid all hardware/software race
conditions. This simple mechanism allows software to simply link
qTDs to the queue head and activate them, then the host controller
will always find them if/when they are reachable."
This is achieved by keeping an "inactivesqtd" entry on the QH list,
and re-using it each time as the start of the next transfer, and
allocating a new qTD to become the next inactivesqtd. Then a new
transfer can be activated by just setting its "active" flag, which
avoids all the previous messing with overlay qTD state in
ehci_set_qh_qtd().
before starting exploring (4 seconds), and extend the wait period
if new USB buses are attached while waiting.
This works around a problem seen when there is more than one EHCI
controller in the system and you kldload usb.ko after the system
has booted. The problem is that usb.ko contains 3 separate PCI
drivers which get initialised one by one (uhci, ohci, ehci), and
when each driver is initialised, all PCI buses are re-probed after
just the addition of that driver. This means that there can be a
significant delay between the attaching of a companion controller
and the subsequent EHCI attach, so it is possible for the companion
controller's USB 1.x bus to be scanned before the EHCI driver gets
a chance to check if there is really a USB 2.x device connected.
that have the specified kind, instead of assuming that there is
only one report of the right kind in the report descriptor.
Submitted by: Morten Johansen
Obtained from: NetBSD (indirectly)
PR: usb/77604
transfers. This fixes some cases where the software toggle tracking
was not doing the right thing. For example, a short transfer that
transferred 0 bytes of the requested qTD transfer size does cause
a toggle change, but the existing code was assuming it didn't.
Reported and tested by: pav
MFC after: 2 weeks
Developed with: Norbert Koch < NKoch at demig dot de >
No response from: freebsd-current@
Tested by: Norbert Koch < NKoch at demig dot de >
MFC after: 1 day
is closed and then reopened. This appears to be necessary now that
we no longer clear endpoint stalls every time a pipe is opened.
Previously we could assume an initial toggle value of zero because
the clear-stall operation resets the device's toggle state.
Reported by: Holger Kipp
MFC after: 3 days
try to use the registrant for numbers in this file, not the OEM that
put their label on it. Use PNY's real number 0x154b. Add another PNY
atachmate with quirks from a PR filed a while ago, but that I can't
seem to find now...
o fix contention window
o silently discard received frames that are too short
o simplify lookup of 802.11a channels (we know they exist)
o fix short preamble support
o add short slot support
o fix eifs settings
o many consistency tweaks
ATI EHCI controllers exhibit simmilar stall issues and require
this dropped interrupts workaround. Be verbose about it.
ehci.c:
ehcivar.h:
Slight change in comments to note about issues surrounding both
VIA and ATI EHCI controllers.
Approved by: iedowse
an interrupt appears to occur before the transfer has been marked
as completed. This caused umass transfers to get stuck, especially
when writing large files. The workaround sets up a timer that
rechecks for missed completed transfers if some operations are still
pending. Other suggested workarounds, such as performing a PCI read
immediately after acknowledging the interrupts, do not appear to
help.
Obtained from: OpenBSD
This is based on MCPC USB mobile phone guide line (MCPC-GL005)
Some other 3G system or so will work with this driver.
Kyocera PHS terminal (a.k.a. Kyopon) is known to work, which
is now supported by umodem(4) driver.
USB HID device that allows to plug two PS2 controllers. This specific
device doesn't work yet but will as soon as we support devices with
multiple report IDs.
MFC after: 3 days
broken report descriptor. While I'm here, make all the other report
descriptors const to match the newly added one.
Obtained from: NetBSD
MFC after: 1 week
lack a report descriptor and don't use the standard interface class.
This patch works around these deficiencies so that the uhid(4) driver
can recognize and use those broken devices.
PR: usb/90141
Submitted by: Ed Schouten <ed@fxq.nl> (with minor mods from me)
MFC after: 1 week
"done" method so that for non-repeat operations we have completely
finished with the transfer by the time the callback is invoked.
This makes it possible to recycle a transfer from within the callback
routine for the same transfer. Previously this almost worked, but
with OHCI controllers calling the "done" method after the callback
would zero out some important fields needed by the recycled transfer.
Only some usb peripheral drivers such as ucom appear to rely on the
ability to reuse a transfer from its callback.
MFC after: 1 week
appeared to rely on all kinds of non-guaranteed behaviours: the
transfer abort code assumed that TDs with no interrupt timeout
configured would end up on the done queue within 20ms, the done
queue processing assumed that all TDs from a transfer would appear
at the same time, and there were access-after-free bugs triggered
on failed transfers.
Attempt to fix these problems by the following changes:
- Use a maximum (6-frame) interrupt delay instead of no interrupt
delay to ensure that the 20ms wait in ohci_abort_xfer() is enough
for the TDs to have been taken off the hardware done queue.
- Defer cancellation of timeouts and freeing of TDs until we either
hit an error or reach the final TD.
- Remove TDs from the done queue before freeing them so that it
is safe to continue traversing the done queue.
This appears to fix a hang that was reproducable with revision 1.67
or 1.68 of ulpt.c (earlier revisions had a different transfer
pattern). With certain HP printers, the command "true > /dev/ulpt0"
would cause ohci_add_done() to spin because the done queue had a
loop. The list corruption was caused by a 3-TD transfer where the
first TD completed but remained on the internal host controller
done queue because it had no interrupt timeout. When the transfer
timed out, the TD got freed and reused, so it caused a loop in the
done queue when it was inserted a second time from a different
transfer.
Reported by: Alex Pivovarov
MFC after: 1 week
just discard the received frame and reuse the old mbuf.
This should prevent the connection from stalling after high network traffic.
MFC after: 2 weeks
from the printer and discarding the data even if the ulpt device
was opened for reading. This resulted in crashes because two
conconcurrent read transfers were using the same transfer structure.
PR: usb/88886
Reported By: Alex Pivovarov
MFC after: 1 week
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
---snip---
FYI this bit isn't needed for FreeBSD - I think it came from either
OpenBSD or NetBSD where arc4random() wasn't available during cold
boot.
---snip---
Explained by: iedowse
Synchronise with NetBSD upto rev 1.19:
- Allow 32 chars in the saved vendor string.
- Some NetBSD-only changes.
- Some missing parts (define, variable).
ehci_pci.c:
Add vendor ids for ATI and Philips.
Add identification strings for the following:
o ALi's M5239
o AMD 8111
o ATI SB200, SB400
o Intel 6300ESB, ICH4, ICH5, ICH7
o NVIDIA nForce 2, nForce 3, nForce 4
o Philips ISP156x
ehcireg.h:
We're at the same level as rev 1.18 from NetBSD.
usb_port.h:
NetBSD/OpenBSD specific things
Obtained from: NetBSD via DragonFly
No comment from: usb@
so that devd can match on it. This field was already available to
usbd and is used by a number of usbd.conf entries, so now it is
possible to transfer those entries to devd.conf.
Submitted by: Anish Mistry
o add ic_curchan and use it uniformly for specifying the current
channel instead of overloading ic->ic_bss->ni_chan (or in some
drivers ic_ibss_chan)
o add ieee80211_scanparams structure to encapsulate scanning-related
state captured for rx frames
o move rx beacon+probe response frame handling into separate routines
o change beacon+probe response handling to treat the scan table
more like a scan cache--look for an existing entry before adding
a new one; this combined with ic_curchan use corrects handling of
stations that were previously found at a different channel
o move adhoc neighbor discovery by beacon+probe response frames to
a new ieee80211_add_neighbor routine
Reviewed by: avatar
Tested by: avatar, Michal Mertl
MFC after: 2 weeks
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
when using mice containing a tilt movement: there was a missing
usb_callout_init() for the UMS_SPUR_BUT_UP quirk code, and UMS_T
was defined to the same flag value as UMS_SPUR_BUT_UP.
Reported by: flz
MFC after: 3 days
over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
through umass(4), in order to make cdcontrol(1) to issue commands to
a USB CD driver.
The command IDs were obtained from the CAM subsystem. This was tested
on half dozen of USB CD drivers from different vendors.
Suggested by: "intron" <intron at intron dot ac>
PR: usb/83439
Reviewed by: sanpei
MFC After: 1 week
succeed. There are many printers that return status over the read
channel, and if we wait for the status to become ready, then we can't
find the status automatically. Linux doesn't wait, nor does it ever
seem to really check the status in any meaningful way... If there
really is a problem, the writes to the bulk out endpoint will still
fail (like they would if the printer was ready and then ran out of
paper or became unready).
In addition, there are a number of printers being made that emulate
the 'status' byte by returning '0' always rather than '0x18'. This
fixes the EBUSY on open timeouts on those printer as well.
Reviewed by: the defining silence on usb@
o Indent usb ids properly
o Check the return value of if_alloc()
o Call if_free() in ural_detach()
Reviewed by: silby (mentor)
Approved by: re (scottl)
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
are used onboard in most of the newer PCI-based sun4u machines
(cosmetic change as they were also already probed as generic OHCI
without this). Detect whether their intpin register is valid and
correct it if necessary, i.e. set the respective IVAR to the right
value for allocating the IRQ resource, as some of them come up
having it set to 0 (mainly those used in Blade 100 and the first
one on AX1105 boards). This fixes attaching affected controllers.
Correcting the intpin value might be better off in the PCI code
via a quirk table but on the other hand gem(4) and hem(4) also
correct it themselves and at least for the USB controller part
the intpin register is truely hardwired to 0 and can't be changed.
This means that we would have to hook up the quirk information
in a lot of places in the PCI code (i.e. whenever the value of the
intpin register is read from or written to the pci_devinfo of the
respective device) in order to do it the right way.
MFC after: 1 month
whether or not the receive pipe is stopped. This ensures that we
do not attempt to start the same transfer twice, and it allows
ucomstop() to skip the restarting of the read pipe if it was not
originally running, such as when called indirectly from ucomreadcb().
PR: kern/79420
MFC after: 1 day
This ensures that we explore EHCI busses before their companion
controllers' busses, so that ports connected to full/low speed
devices will be properly routed to the companion controllers by the
time the OHCI/UHCI exploration occurs.
found it guilty in putting the card into unusable state after UP->DOWN->UP
media status change.
Looks like some of register writes in this functions mess up PHY interface.
No visible regressions has been found after commenting this code out -
the card properly handles forceful local mode changes and auto-detects changes
made remotely (tested with Auto, 10HD, 10FD, 100HD, 100FD).
Sponsored by: PBXpress Inc.
MFC after: 3 days
with the wrong language parameter when retrieving the device serial
number. This invalid request caused some devices not to work at
all.
PR: usb/79190
Submitted by: Hans Petter Selasky <hselasky@c2i.net>
FreeBSD based on aue(4) it was picked by OpenBSD, then from OpenBSD ported
to NetBSD and finally NetBSD version merged with original one goes into
FreeBSD.
Obtained from: http://www.gank.org/freebsd/cdce/
NetBSD
OpenBSD
configure_final(), assert that "cold" is true in usb_cold_explore()
when there are busses to explore. When USB is kldloaded after boot,
usb_cold_explore() will still get invoked but the list of busses
to explore in that case should always be empty.
transfer, which lead to panics or page faults. For example if a
transfer timed out, another thread could come along and attempt to
abort the same transfer while the timeout task was sleeping in
the *_abort_xfer() function.
Add an "aborting" flag to the private transfer state in each host
controller driver and use this to ensure that the abort is only
executed once. Also prioritise normal abort requests over timeouts
so that the callback is always given a status of USB_CANCELLED even
if the timeout-initiated abort began first.
The crashes caused by this bug were mainly reported in connection
with lpd printing to a USB printer.
PR: usb/78208, usb/78986
system have been attached, but no later. This ensures that we do
not explore ohci or uhci busses before the companion echi controller
has been initialised, so it should fix the problem of multi-speed
USB devices getting attached as USB 1 devices first and then
re-attached as USB 2.
Some further changes are needed on architectures that do not currently
allow hooks to be inserted before configure_final() - alpha, ia64,
powerpc and sparc64. On these architectures the exploration will
now be delayed until the usb kthread runs.
cleared if the host controller retries the transfer and is successful,
but we were interpreting these bits as indicating a fatal error.
Ignore these error bits, and instead use the HALTED bit to determine
if the transfer failed. Also update the USBD_STALLED detection to
ignore these bits.
Obtained from: OpenBSD
between passes over a QH. Previously the accesses to a QH were
bunched together in time, so the interval was often much longer
than intended. This now appears to match the diagrams in the EHCI
spec, so remove the XXX comment.
ever working correctly: the code was linking the QHs together but
then immediately overwriting the "next" pointers. Oops. Also
initialise qh_endphub, since the EHCI spec says that we should
always set the pipe multiplier field to something sensible.
This appears to make basic split transactions work, so enable split
transactions for control, bulk and interrupt pipes (split isochronous
transfers are not yet implemented). It should now be possible to
use USB1 devices even when they are connected through a USB2 hub.
o usb_subr.c, add delta 1.119:
Move usb_get_string() and make it public.
o usbdi.c, bring on par with 1.106, this includes:
- Make an iterator abstraction for looping through all descriptors.
- Whine about not being able to figure out default language if we are debugging.
- Move usb_get_string() and make it public.
o usbdi.h, bring on par with 1.64, this includes:
- Make an iterator abstraction for looping through all descriptors.
- Move usb_get_string() and make it public.
o usbdi_util.c, bring on par with 1.42, this includes:
- Add usbd_get_protocol().
- Use NULL instead of 0.
- Fix (mostly harmless) typo.
- Move utility routine from uirda.c to usbdi_util.c.
o usbdi_util.h, bring on par with 1.31, this includes:
- Add usbd_get_protocol().
- Move utility routine from uirda.c to usbdi_util.c.
MFC after: 3 days
base transfer speed to CAM. The actual value used (40MB/s) is fairly
arbitrary, but assumes the same 33% overhead as was implied by the
1MB/s figure we used for USB1 devices.
1/ doesn't matter on most of our architectures
2/ will never happen unless we start queueing multiple trasactions
to a single endpoint at one time (which we do not allow yet).
If anyone has a big_endian machine with EHCI they might check this
if they are having problems with EHCI but it's unlikely even there..
Submitted by: Hans Petter Selasky <hselasky@c2i.net>
MFC after: 3 days
to remove a transaction from the async schedule. The previous method didn't
work well and led to the hardware writing to free'd buffers etc, as
it didn't always know that the transaction had been aborted.
Written after consultation with David Brownell who wrote the Linux
EHCI driver.
As part of this give the sqh structure a "previous" pointer.
MFC after: 1 week
rather than a softc pointer (with the bus structure at the start).
This is a non-functional change. It just helps when reading the code to
know that the ehci, ohci and uhci drivers share the bus structure, not the
entire softc.
ADVANCELOGIC->AVANCELOGIC (nothing in the tree uses it, so safe to do)
sort HAGIWARA vendor entry
sort ACTIONTAR vendor entry
Minor change to SYSTEMTALKS vendor entry.
Add $NetBSD$ in a comment at the top
Update copyright dates
Update header comment
Add some of the entries not present in FreeBSD's usbdevs file
Harmonize some descriptions with NetBSD where NetBSD's were shorter
More work needs to happen here, as there's many conflicting vendor
names. There's also more harmonization that can happen before that
problem is tackled.
This was inspired by recent discussions, but none of the patches
posted were consulted to produce this commit. Other, similar ones
will follow.
This is part of an ongoing cycle of commits on all the BSDs to
merge the USB vendor and device defintions..
A merge from OpenBSD is still pending.
Submitted by: barry bouwsma (freebsd-misuser@NOSPAM.dyndns.dk)
Obtained from: NetBSD
MFC after: 1 week
to better keep track of the total amoutn transferred during a
transfer. Seems similar to some code in the NetBSD version.
I notice they have incorporated matches from him so I don't know which
direction it went.
Submitted by: damien.bergamini@free.fr
Obtained from: patches to make the ueagle driver work
MFC after: 1 week
Now only things that are different between us and NetBSD show up.
Means that these files are more of NetBSD style in some places but
since thay are NetBSD files, um, that's ok.
Obtained from: NetBSD
MFC after: 1 week
backed out commits were trying to address: when cancelling the timeout
callout, also cancel the abort_task event, since it is possible that
the timeout has already fired and set up an abort_task.
reports of problems. The bug is probably that there are cases where
`xfer->timeout && !sc->sc_bus.use_polling' is not a suitable test
for an active timeout callout, so an explicit flag will be necessary.
Apologies for the breakage.
transfer timeouts that typically cause a transfer to be completed
twice, resulting in panics and page faults:
o A transfer completion interrupt could arrive while an abort_task
event was set up, so the transfer would be aborted after it had
completed. This is very easy to reproduce. Fix this by setting
the transfer status to USBD_TIMEOUT before scheduling the
abort_task so that the transfer completion code will ignore it.
o The transfer completion code could execute concurrently with the
timeout callout, leaving the callout blocked (e.g. waiting for
Giant) while the transfer completion code runs. In this case,
callout_stop() does not prevent the callout from running, so
again the timeout code would run after the transfer was complete.
Handle this case by checking the return value from callout_stop(),
and ignoring the transfer if the callout could not be removed.
o Finally, protect against a timeout callout occurring while a
transfer is being aborted by another process. Here we arrange
for the timeout processing to ignore the transfer, and use
callout_drain() to ensure that the callout has really gone before
completing the transfer.
This was tested by repeatedly performing USB transfers with a timeout
set to approximately the same as the normal transfer completion
time. In the PR below, apparently this occurred by accident with a
particular printer and the default timeout.
PR: kern/71491
just a convenience function to be called from debuggers that gets
compiled in when EHCI_DEBUG is defined. Move its declaration to
make this more obvious.
o Reduce the interrupt delay to 2 microframes.
o Follow the spec more closely when updating the overlay qTD in the QH.
o No need to generate an interrupt at the data part of a control
transfer, it's generated by the status transfer.
o Make sure to update the data toggle on short transfers.
o Turn the printf about needing toggle update into a DPRINTF.
o Keep track of what high speed port (if any) a device belongs to
so we can set the transaction translator fields for the transfer.
o Verbosely refuse to open low/full speed pipes that depend on
unimplemented split transaction support.
o Fix various typos in comments.
Obtained from: NetBSD
asynchronous. I realize that this means the custom application will
not work as written, but it is not okay to break most users of ugen(4).
The major problem is that a bulk read transfer is not an interrupt
saying that X bytes are available -- it is a request to be able to
receive up to X bytes, with T timeout, and S short-transfer-okayness.
The timeout is a software mechanism that ugen(4) provides and cannot
be implemented using asynchronous reads -- the timeout must start at
the time a read is done.
The status of up to how many bytes can be received in this transfer
and whether a short transfer returns data or error is also encoded
at least in ohci(4)'s requests to the controller. Trying to detect
the "maximum width" results in using a single buffer of far too
small when an application requests a large read.
Even if you combat this by replacing all buffers again with the
maximal sized read buffer (1kb) that ugen(4) would allow you to
use before, you don't get the right semantics -- you have to
throw data away or make all the timeouts invalid or make the
short-transfer settings invalid.
There is no way to do this right without extending the ugen(4) API
much further -- it breaks the USB camera interfaces used because
they need a chain of many maximal-width transfers, for example, and
it makes cross-platform support for all the BSDs gratuitously hard.
Instead of trying to do select(2) on a bulk read pipe -- which has
neither the information on desired transfer length nor ability to
implement timeout -- an application can simply use a kernel thread
and pipe to turn that endpoint into something poll-able.
It is unfortunate that bulk endpoints cannot provide the same semantics
that interrupt and isochronous endpoints can, but it is possible to just
use ioctl(USB_GET_ENDPOINT_DESC) to find out when different semantics
must be used without preventing the normal users of the ugen(4) device
from working.
New devicename is ttyy{unit}{port}
No callout devices created as there is no modemcontrol on these ports.
Add data structure to represent each port to avoid excessive array use.
from within umass_ufi_transform(). This includes the 12-byte commands
FORMAT_UNIT, WRITE_AND_VERIFY, VERIFY, and READ_FORMAT_CAPACITIES
(sorted in numerical order).
Reviewed by: ken, scottl
MFC after: 2 weeks
data endpoints. The control endpoint doesn't need read/write/poll
operations, and more importantly, the thread counts should be
separate so that the control endpoint can properly reference itself
while deleting and recreating the data endpoints.
* Add some macros that handle referencing/releasing devices, and use them
for sleeping/woken-up and open/close operations as apppropriate.
* Use d_purge for FreeBSD, and a loop testing the open status for all
the endpoints for NetBSD and OpenBSD, so that when the device is
detached, the right thing always happens.
restart the current waiting transfer. If this isn't done, the device's
next transfer (that we would like to do a short read on) is going to
return an error -- for short transfer.
* For bulk transfer endpoints, restore the maximum transfer length each
time a transfer is done, or the first short transfer will make all the
rest that size or smaller.
* Remove impossibilities (malloc(M_WAITOK) == NULL, &var == NULL).
to make sure the pipe is ready. Some devices apparently don't support
the clear stall command however. So what happens when you issue such
devices a clear stall command? Typically, the command just times out.
This, at least, is the behavior I've observed with two devices that
I own: a Rio600 mp3 player and a T-Mobile Sidekick II.
It used to be that after the timeout expired, the pipe open operation
would conclude and you could still access the device, with the only
negative effect being a long delay on open. But in the recent past,
someone added code to make the timeout a fatal error, thereby breaking
the ability to communicate with these devices in any way.
I don't know exactly what the right solution is for this problem:
presumeably there is some way to determine whether or not a device
supports the 'clear stall' command beyond just issuing one and waiting
to see if it times out, but I don't know what that is. So for now,
I've added a special case to the error checking code so that the
timeout is once again non-fatal, thereby letting me use my two
devices again.
This changes the naming of USB serial devices to: /dev/ttyU%d and
/dev/cuaU%d for call-in and call-out devices respectively. (Please
notice: capital 'U')
Please also note that we now have .init and .lock devices for USB
serial ports. These are not persistent across device removal. devd(8)
can be used to configure them on attachment time.
These changes also improve the chances of the system surviving if
the USB device is unplugged at an inconvenient time. At least we
do not rip things apart while there are any threads in the device
driver anymore.
Remove cdevsw, rely on the tty generic one.
Don't make_dev(), use ttycreate() which does all the magic.
In detach, do close procesing if we ripped things apart
while the device was open. Call ttyfree() once we're done
cleaning up.
select(2), and discovered to my horror that ugen(4)'s bulk in/out support
is horribly lobotomized. Bulk transfers are done using the synchronous
API instead of the asynchronous one. This causes the following broken
behavior to occur:
- You open the bulk in/out ugen device and get a descriptor
- You create some other descriptor (socket, other device, etc...)
- You select on both the descriptors waiting until either one has
data ready to read
- Because of ugen's brokenness, you block in usb_bulk_transfer() inside
ugen_do_read() instead of blocking in select()
- The non-USB descriptor becomes ready for reading, but you remain blocked
on select()
- The USB descriptor becomes ready for reading
- Only now are you woken up so that you can ready data from either
descriptor.
The result is select() can only wake up when there's USB data pending. If
any other descriptor becomes ready, you lose: until the USB descriptor
becomes ready, you stay asleep.
The correct approach is to use async bulk transfers, so I changed
the read code to use the async bulk transfer API. I left the write
side alone for now since it's less of an issue.
Note that the uscanner driver has the same brokenness in it.
panic on hub detach bugs that have been reported. This work around
detaches the device before deleting it. This changes the detach order
from in-order to pre-order. This avoids uhub's deleting the children
after its subdevs has been deleted.
This is only a workaround. This leads to a strange condition in the
device tree where attached devices are children of detached ones. I
really don't know what that's supposed to mean, but does violate my
sense of POLA. Fortunately, the violation is short lived, which is
why I'm going ahead and committing the work around.
# We really need to consider life w/o the multiple nested layers of
# compatibility macros. They make finding bugs like this *MUCH*
# harder.
Patch by: iadowse
MT5 before: next_release(5.3-BETA5) (unless someting better comes along)
redundant at this point and should be retired). Don't free subdevs if
we don't attach any devices. This was leaving stale device_t's
around. Don't touch the device if it isn't attached since the name
isn't meaningful then. Switch from strncpy (properly used) to
strlcpy.
From a patch submitted by Peter Pentchev
device_t instances when no driver attaches. They are left around, and
we need to remember them.
# The usbd_device_handle->subdevs[] array likely is completely bogus
# at this point, but one change at a time, since its removal will need
# to have similar code replace it extracted from newbus.
Part of the patch submitted by Peter Pentchev after an excellent
analysis of the underlying problems.
MFC After: 1 week
produced better results for a test program I had here, it didn't
substantially change the number of crashes that I saw. Both the old
code and the new code seemed to produce the same crashes from the usb
layer. Since the new code also solves a close() crash, go with it
until the underlying issues wrt devices going away can be addressed.
The reference counts are there to block detach until the sleepers in
read/write/ioctl have gotten out, not to prevent the open device from
going away. Restore the old behavior so that we have a chance to wake
up sleepers when the usb device goes away, so they can properly return
EIO back to the caller when this happens.
Otherwise, we have a guarnateed panic waiting to happen when a device
detaches with an active read channel.
This should be merged to 5 asap.
to RS232 bridges, such as the one found in the DeLorme Earthmate USB GPS
receiver (which is the only device currently supported by this driver).
While other USB to serial drivers in the tree rely heavily on ucom, this
one is self-contained. The reason for that is that ucom assumes that
the bridge uses bulk pipes for I/O, while the Cypress parts actually
register as human interface devices and use HID reports for configuration
and I/O.
The driver is not entirely complete: there is no support yet for flow
control, and output doesn't seem to work, though I don't know if that is
because of a bug in the code, or simply because the Earthmate is a read-
only device.
Without this, the device cannot detect the end of ethernet packets
whose size is a multiple of the USB packat size.
PR: kern/70474
Submitted by: Andrew Thompson <andy@fud.org.nz>
MFC after: 1 week
o reprobe children when a new driver is added to uhub
o fix the usbd_probe_and_attach to set the ivars to a malloc'd area, as well
as freeing the ivars on child destruction.
o Don't delete children that don't attach. Evidentally, the need to do this
is a common misconception.
o minor formatting foo that may violate style(9) at the moment, but keeps the
diffs against my p4 tree smaller.
This does not solve the ugen gobbling things up problem, but the fixes
I have for that expose bugs in other parts of the tree...
if_start routines cannot currently be entered without Giant. When
the kernel is running with debug.mpsafenet != 0, this will defer
if_start execution to a task queue thread holding Giant, which may
introduce additional latency, but avoid incorrect execution.
Suggested by: dfr
skip blocks that are too big by a factor of two or greater. This
avoids some cases of extremely inefficient memory use that can occur
when large (e.g. 64k) blocks on the free list get used when allocating
a 4k chunk of 64-byte fragments. Because fragments have their own
free list, the 60k difference got lost forever every time.
system BIOS to disable legacy device emulation as per the "EHCI
Extended Capability: Pre-OS to OS Handoff Synchronisation" section
of the EHCI spec. BIOSes that implement legacy emulation using SMIs
are supposed to disable the emulation when this procedure is performed.
to be particularly correct or optimal, but it seems to be enough
to allow the attachment of USB2 hubs and USB2 devices connected via
USB2 hubs. None of the split transaction support is implemented in
our USB stack, so USB1 peripherals will definitely not work when
connected via USB2 hubs.
Improve child_detached a little and make it conform better to
style(9). Also, improve comment about what we'll be doing in the
future about driver_added. Soon it will be possible to kldload usb
drivers and have them attach w/o a need to disconnect/reconnect them.
usbdi.c rev. 1.104, author: mycroft
ugen_isoc_rintr() may recycle the xfer immediately. Therefore, we
avoid touching the xfer after calling the callback in
usb_transfer_complete(). From PR 25960.
future:
rename ttyopen() -> tty_open() and ttyclose() -> tty_close().
We need the ttyopen() and ttyclose() for the new generic cdevsw
functions for tty devices in order to have consistent naming.
rev. 1.67, author: mycroft
Fix a byte order error.
rev. 1.68, author: mycroft
Adjust some silliness that was causing us to do extra work for
"frame list rollover" interrupts, which we pretty much ignore.
Obtained from: NetBSD
rev. 1.68, author: mycroft
Ignore a port error that happens to come in at the same time as a
connect status change. Some root hubs seem to report both.
Obtained from: NetBSD
bus interfaces. These interfaces use the FTDI chipset with different
Vendor and Product IDs.
Add two additional baud rate enumerations. The vehicle bus interfaces
use a baud rate of 2000000. Also add 3000000 as it is the other FTDI
baud divisor special case.
I've commited a slightly different patch from that provided in the PR as
I changed the matching code a bit yesterday.
Submitted by: Mike Durian <durian at shadetreesoftware.com>
PR: kern/67357
operations when the refcount doesn't protect the opens and closes. Fix
this, and don't actually let a time out happen: now ugen(4) devices do
not get freed out from under the programs with them open.
uhid.c (1.61), author: jdolecek
add support for USB_GET_DEVICEINFO and USB_GET_STRING_DESC ioctls,
with same meaning as for ugen(4)
usbdi_util.h (1.29), usb_quirks.c (1.50), uhid.c (1.62),
ugen.c (1.68), usb_subr.c (1.114) author: mycroft
Yes, some devices return incorrect lengths in their string
descriptors. Rather than losing, do what Windows does: just
request the maximum size, and allow a shorter response. Obsoletes
the need for UQ_NO_STRINGS, and therefore these "quirks" are removed.
usb_subr.c (1.116), author: mycroft
In the "seemed like a good idea until I found the fatal flaw"
department... Attempting to read a maximum-size string descriptor
causes my kue device to go completely apeshit. So, go back to the
original method, but allow the device to return a shorter string than
it claimed.
Obtained from: NetBSD
copies.
No current line disciplines have a dynamically changing hotchar, and
expecting to receive anything sensible during a change in ldisc is
insane so no locking of the hotchar field is necessary.
ohci.c (1.147), author: mycroft
Failure to properly mask off UE_DIR_IN from the endpoint address
was causing OHCI_ED_FORMAT_ISO and EHCI_QH_HRECL to get set
spuriously, causing rather interesting lossage.
Suddenly I get MUCH better performance with ehci...
ohci.c (1.148), author: mycroft
Adjust a couple of comments to make it clear WTF is going on.
Obtained from: NetBSD
ehci.c (1.55), ehcireg.h (1.16); author: mycroft
Set the data toggle correctly, and use EHCI_QTD_DTC. This fixes
problems with my ALi-based drive enclosure (it works now, rather
than failing to attach). Also seems to work with a GL811-based
enclosure and an ASUS enclosure with a CD-RW, on both Intel and
NEC controllers.
Note: The ALi enclosure is currently very SLOW, due to some issue
with taking too long to notice that the QTD is complete. This
requires more investigation.
ehci.c (1.56); author: mycroft
Failure to properly mask off UE_DIR_IN from the endpoint address
was causing OHCI_ED_FORMAT_ISO and EHCI_QH_HRECL to get set
spuriously, causing rather interesting lossage.
Suddenly I get MUCH better performance with ehci...
ehci.c (1.58); author: mycroft
Fix a stupid bug in ehci_check_intr() that caused use to try to
complete a transaction that was still running. Now ehci can
handle multiple devices being active at once.
ehci.c (1.59); author: enami
As the ehci_idone() now uses the variable `epipe'
unconditionally, always declare it (in other words, make this
file compile w/o EHCI_DEBUG).
ehci.c (1.60); author: mycroft
Remove comment about the data toggle being borked.
ehci.c (1.61); author: mycroft
Update comment.
ehci.c (1.62); author: mycroft
Adjust a couple of comments to make it clear WTF is going on.
ehci.c (1.63); author: mycroft
Fix an error in a debug printf().
ehci.c (1.64), ehcireg.h (1.17); author: mycroft
Further cleanup of toggle handling. Now that we use EHCI_QH_DTC,
we don't need to fiddle with the TOGGLE bit in the overlay
descriptor, so minimize how much we fuss with it.
Obtained from: NetBSD
Thanks to Sam for importing tags in a way that allowed this to be done.
Submitted by: Gleb Smirnoff <glebius@cell.sick.ru>
Also allow the sr and ar drivers to create netgraph versions of their modules.
Document the change to the ksocket node.
Several changes:
* Implement read for ulpt.
* If the device is not opened for reading, occasionally drain any
data the printer might have (but don't hammer the printer with reads).
* Lower the buffer size to one page.
The driver seems to work with more printers now.
Obtained from: NetBSD
as otherwise the junk it contains may cause uhub_explore to give
up without ever trying to restart the port. This fixes the following
errors I was seeing with a VIA UHCI controller:
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
called ttyldoptim().
Use this function from all the relevant drivers.
I belive no drivers finger linesw[] directly anymore, paving the way for
locking and refcounting.
pipes, since open pipes are linked off a usbd_interface structure
that is free()'d when the configuration index is changed. Attempting
to close or use such pipes later would access freed memory and
usually crash the system.
The only driver that is known to trigger this problem is if_axe,
which is itself at fault, but it is worth detecting the situation
to avoid the obscure crashes that result from this type of easily
made driver mistakes.
in all USB ethernet drivers. The qdat structure contains a pointer
to the interface's struct ifnet and is used to process incoming
packets, so simultaneous use of two similar devices caused crashes
and confusion.
The if_udav driver appeared in the tree since Daan's PR, so I made
similar changes to that driver too.
PR: kern/59290
Submitted by: Daan Vreeken <Danovitsch@Vitsch.net>
MFNetBSD 1.177; author: toshii
Use the correct wValue to get hub desriptors.
Also, make wValue checks of root hub codes less strict.
MFNetBSD 1.178: author: martin
Interrupt descriptors might become invalid while being processed in
uhci_check_intr - so remember their next pointer before calling it.
Patch provided by Matthew Orgass in PR kern/24542.
Obtained from: NetBSD
that the OHCI driver uses. Broken OHCI devices (like the controller
in my laptop, apparently) like to set this bit at times. Research
through google shows that this problem has shown up on other systems
as well.
As the scheduling overrun handler doesn't actually do anything, and
the only effect is console spamming, disabling the interrupt seems
to be the right thing to do. (And it is also what linux 2.6 does.)
