was major changes to initialize RF chipset and set H/W registers and
removed a lot of magic numbers on code. Details are as follows:
- uses the endpoint 0x89 to get TX status information which used to
get TX complete or retry numbers or get a beacon interrupt. It's
only valuable for RTL8187B.
- removes urtw_write[8|16|32]_i functions that it's useless now.
- uses ic->ic_updateslot to set SLOT, SIFS, DIES, EIFS, CW_VAL
registers that doesn't set these whenever the channel is changed.
- code for initializing RF chipset for RTL8187B changed a lot that
there was many problems on TX transfers so it doesn't work properly
even if just for a ping/pong. Now it becomes more stable than
before that TX throughputs using netperf(1) were about 15 ~ 17Mbps/s
though sometimes it encounters packet losses.
- removes a lot of magic numbers that in the previous all of
representing RX and TX descriptors were consisted of magic numbers
and structures. It'd be more readable rather than before.
- calculates TX duration more accurately for urtw(4) devices.
- style(9)
all host controllers at the same time, we avoid problems where the BIOS will
actually write to the USB registers of all the USB host controllers every time
we handover one of them, and consequently reset the OS programmed values.
Submitted by: avg
Reviewed by: jhb
Sun Type 6 USB keyboard support added in rev 1.46 conflicted with
some scan codes used in Japanese keyboards because the scan code
conversion routine was ambiguous for the overlapped codes.
PR: ports/134005
Submitted by: YAMASHIRO Jun
The EHCI HW can use the qtd_next field instead of qtd_altnext when a short
packet is received. This contradicts what is stated in the EHCI datasheet.
Also the total-bytes field in the status field of the following TD gets
corrupted upon reception of a short packet! We work this around in software by
not queueing more than one job/TD at a time of up to 16Kbytes! The bug has been
seen on multiple INTEL based EHCI chips. Other vendors have not been tested
yet.
- Applications using /dev/usb/X.Y.Z, where Z is non-zero are affected, but not
applications using LibUSB v0.1, v1.2 and v2.0.
- Mass Storage (umass) is affected.
Submitted by: Hans Petter Selasky
MFC after: 3 days
- Add quirk for ATI SB600 and SB700 to free SMB controller
- Correct schedule sleep time to 10us on the VIA ehci controller
Reported by: Dorian B<FC>ttner, Andriy Gapon
Submitted by: Hans Petter Selasky
- clean up USB detach logic. There seems to be some problems detaching multiple
USB HUBs connected in series from the root.
- after this patch the rule is:
1) Always use device_detach() on the USB HUB first.
2) Never just device_delete_child() on the USB HUB, because that function
will traverse to all the device leaves and free them first, and then the USB
stack will free the devices twice which doesn't work very well.
- make sure the did DMA delay gets set after the timeout has elapsed to make
logic more clear. There is no functional difference.
Submitted by: Hans Petter Selasky
turn ends our usb process. This means the proc pointer becomes invalid and will
panic if a new kthread is added. Count the number of threads and clear the proc
pointer on the last one.
Suggested by: julian
MFC after: 3 days
being polled.
- Remove the need for Giant from the USB HUB driver.
- Leave device unconfigured instead of disabling the USB port
when Huawei Autoinstall disk detection triggers. This should
fix problems that the Huawei device is not detected after
Autoinstall eject is issued.
- Reported by: Nikolay Antsiferov
- Fix memory use after free race for USB character devices.
- Reported by: Lucius Windschuh
- Factor out the enumeration lock into three functions to make the
coming newbus lock conversion more easy.
- usbd_enum_lock
- usbd_enum_unlock
- usbd_enum_is_locked
Submitted by: hps
enable the ones we want. This has been changed to better
match the ADMtek's reference design to avoid setting the
power-down configuration line of the PHY at the same time
it is reset.
Submitted by: John Hood via hps
direction even if the actual device is opened for read and
write. Fix fflags check so that the UFM and URIO drivers work.
Reported by: Krassimir Slavchev
Submitted by: hps
keys are pressed.
- Reported by: Various people
- add sysctl to disable keyboard led control request
- Reported by: Yoshihiro Ota
- Save system CPU usage: Patch to stop keyboard timer when no
keys are pressed.
Submitted by: hps
MFC after: 3 days
- usb_pc_cpu_invalidate() is called between [consecutive] reads from a device,
so a sequence of BUS_DMASYNC_POSTREAD and _PREREAD should be used. Note we
cannot use or'ed shorthand ( _POSTREAD | _PREREAD) for BUS_DMASYNC flags, as
the low level bus dma sync operation is implementation dependent and we
cannot assume the required order of operations to be guaranteed.
- usb_pc_cpu_flush() is called before writing to a device, so
BUS_DMASYNC_PREWRITE should be used.
Submitted by: Grzegorz Bernacki
Reviewed by: HPS, arm@, usb@ ML
Tested by: HPS, Mike Tancsa
Approved by: re (kib)
Obtained from: Semihalf
cosmetic change to reduce cruft in the proc table.
Also change the idle wait message to `-` like how taskqueues are.
Reviewed by: julian
Approved by: re (kib)
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
USB core:
- add support for defragging of written device data.
- improve handling of alternate settings in device side mode.
- correct return value from usbd_get_no_alts() function.
- reported by: HPS
- P4 ID: 166156, 166168
- report USB device release information to devd and pnpinfo.
- reported by: MIHIRA Sanpei Yoshiro
- P4 ID: 166221
Submitted by: hps
Approved by: re
See PR description for more info. Patch is
implemented differently than suggested, but
having the same result.
PR: usb/137188
Submitted by: hps
Approved by: re
- add support for defragging of written device data.
- improve handling of alternate settings in device side mode.
- correct return value from usbd_get_no_alts() function.
- reported by: HPS
- P4 ID: 166156, 166168
- report USB device release information to devd and pnpinfo.
- reported by: MIHIRA Sanpei Yoshiro
- P4 ID: 166221
Submitted by: hps
Approved by: re
- Add minimum polling support to drive UMASS
and UKBD in case of panic.
- Add extra check to ukbd probe to fix problem about
mouse devices attaching like keyboards.
- P4 ID: 166148
Submitted by: hps
Approved by: re
- add support for setting the UMS polling rate through -F option
passed to moused.
- requested by Alexander Best
- P4 ID: 166075
PR: usb/125264
Submitted by: hps
Approved by: re
USB CORE: busdma improvement
For single segment allocations the boundary field
of the BUSDMA tag should be zero. Currently all
single segment allocations are less than or equal
to 4096 bytes, so the limit does not kick in. If
any single segment USB allocations would be greater
than 4K, then it would be a problem.
Approved by: re (kensmith)
Obtained from: HPS
Giant was only used here to lock down a bit mask of allocated unit
numbers. Change the code to use its own mutex.
Reviewed by: hselasky
Approved by: re (kib)
- Add support for devices that handle set and clear stall in hardware.
- Add missing get timestamp function
- Add more xfer flags
Submitted by: Hans Petter Selasky
Approved by: re (kib)
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
Note that I also added the usbdev to the list, because the 8813 version
is not yet known there. I might have twisted the sorting there but because
8813 comes before 8818, I added it before that (with _8813 to differentiate)
the item.
PR: 135628
Submitted by: Yoshikazu GOTO <goto at on-link dot jp>
Approved by: imp (mentor, implicit)
so that it isn't exposured unless needed. In particular this means
that it's easier to tune the memory layout based on board details.
While here, remove inclusion of <machine/intr.h> from mvreg.h. This
also contains exposure to SoC specifics in MI drivers, because NIRQ
depends on the SoC.
ICIDU NI-707503 which is donated by Nick Hibma (great thanks!). Though
it has a MAXIM RF (0x8) there's some success reports with using GCT RF
(0x9) codes and it worked well for ICIDU NI-707503 too. So codes for
MAXIM and GCT RFs are integrated.
Before this commit, if I rememeber correctly, MAXIM RF is never tested
that it seems it's a first report working with FreeBSD.
part identified as Sunplus Technology Inc. This
happens to sit in a Rosewill RX81U-ES-25A 2.5" SATA
to USB 2.0 external enclosure.
Reviewed by: Hans Petter Selasky
I don't want people to override the mutex when allocating a TTY. It has
to be there, to keep drivers like syscons happy. So I'm creating a
tty_alloc_mutex() which can be used in those cases. tty_alloc_mutex()
should eventually be removed.
The advantage of this approach, is that we can just remove a function,
without breaking the regular API in the future.
- add key mappings for fn keys
- byte swapping for certain models
- Fix leds for keyboards which require an ID byte for the HID output structures
Submitted by: Hans Petter Selasky
Some hardware easily comes out of sync with regard to whether the current or
the next control transfer should be stalled, if a stall command is always
issued before receiving the SETUP packet. After this patch the stall command
will only be issued when a transfer should actually be stalled.
Submitted by: Hans Petter Selasky
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
bug referencing a destroyed lock within TX callbacks during device
detach.
Submitted by: hps (original version)
Tested by: Lucius Windschuh <lwindschuh at googlemail.com>
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
Change the roothub exec functions to take the usb request and data pointers
directly rather than placing them on the parent bus struct.
Submitted by: Hans Petter Selasky
Fix a bug in the USB power daemon code where connection of multiple HUBs in
series would result in incorrect device suspend.
Reported by: Nicolas xxx@wanadoo.fr
Submitted by: Hans Petter Selasky
Use direct reference to parent high-speed HUB instead of indirect, due to
pointer clearing race at detach of parent USB HUB.
Reported by: kientzle
Submitted by: Hans Petter Selasky
PR: usb/133545
Refactor how we interface with the root HUB. This is achieved by making a
direct call from usb2_do_request to the host controller for root hub requests,
this call will perform the controller specific register read/writes and return
the error code.
This cuts out a lot of code in the host controller files and saves one thread
per USB bus.
Submitted by: Hans Petter Selasky
- add support for more complicated HID descriptors which can have multiple
definitions of the same field.
- remove old modulo patch in ums, which I think is due to bad HID parsing,
which should be fixed now.
Reported by: netchild
Submitted by: Hans Petter Selasky
Some cancelable flags are always true. Substitute these away. These cancelable
flags were mostly useful with the root HUB which is now handled differently.
Submitted by: Hans Petter Selasky
Refactor how we interface with the root HUB. This cuts around 1200 lines of
code totally and saves one thread per USB bus.
Submitted by: Hans Petter Selasky
- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" which select for which mode
the current xfer entry is active. Options are: a) Device mode only b) Host
mode only (default-by-zero) c) Both modes. This change was scripted using
the following sed script: "s/\.mh\././g".
- the standard packet size table in "usb_transfer.c" is now a function, hence
the code for the function uses less memory than the table itself.
Submitted by: Hans Petter Selasky
- bugfixes after the memory usage reduction patch
- Use "udev->pipes_max" instead of USB_EP_MAX
- Use correct "bmRequestType" for getting the config descriptor.
Submitted by: Hans Petter Selasky
- memory usage reduction by only allocating the required USB pipes and USB
interfaces.
- cleanup some USB parsing functions to be more flexible.
Submitted by: Hans Petter Selasky
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
it is right for only a tiny fraction of these devices and this
wild-card entry is too broad.
# I run a kernel without this entry at all without ill effects...
Workaround for buggy USB hardware not handling new SETUP packet before STATUS
stage is complete, this allows xfers to endpoint0 to return a short frame.
Submitted by: Hans Petter Selasky
Reported by: me
Workaround for buggy USB hardware not handling new SETUP packet before STATUS
stage is complete, this allows xfers to endpoint0 to return a short frame.
Submitted by: Hans Petter Selasky
Reported by: me
- Move tunable defines into usb_core.h and dependancy towards usb_defs.h
- Leave hardcoded defines in "usb_defs.h".
- Allow overriding all tunable defines.
- Add more customisable typedefs.
- Correct maximum device number.
Submitted by: Hans Petter Selasky
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
Fix regression issue in the USB file system interface.
- Use cdev_privdata pointer as indicator of correct file handle.
- Remove redundant FIFO opened flags.
Don't send ZLP at close for ulpt and uscanner devices as this causes some
models to stop working. This reverts back to the USB1 behaviour.
Submitted by: Hans Petter Selasky
More HID parsing fixes for usb mice.
- be less strict on the last HID item usage.
- preserve item size and count accross items
- improve default HID usage selection.
Tested by: ache
Submitted by: Hans Petter Selasky
Fix bugs and improve HID parsing.
- fix possible memory leak found
- fix possible NULL pointer access
- fix possible invalid memory read
- parsing improvements
- reset item data position when a new report ID is detected.
Submitted by: Hans Petter Selasky
o add Transaction Translator support (still missing ISOC xfers)
o add EHCI_SCFLG_BIGEMMIO flag to force big-endian byte-select to be
set in USBMODE
o split reset work into new public routine ehci_reset so bus shim drivers
can force big-endian byte-select before ehci_init
o enable TT and big-endian MMIO
o force a reset before ehci_init to get byte-select setup
Also go back to using USB_EHCI_BIG_ENDIAN_DESC at compile time to enable the
byteswapping and reduce diffs to the original commits.
This fixes the new USB stack on the Cambria board.
the devfs clone handler to open the (invisible) devices on the fly.
The /dev entries are layed out as follows,
/dev/usbctl = master device
/dev/usb/0.1.0.5 = usb device, (<bus>.<dev>.<iface>.<endpoint>)
/dev/ugen0.1 -> usb/0.1.0.0 = ugen link to ctrl endpoint
This also removes the custom permissions model from USB. Bump
__FreeBSD_version to 800066.
Submitted by: rink (earlier version)
- We don't need to exit the Giant mutex when sleeping. This is done
automatically. Replace Giant by NULL mutex for all control requests in the
enumeration path.
- Optimise away duplicate alternate interface selection requests in USB Host
mode.
Submitted by: Hans Petter Selasky
Improvements to "usb2_transfer_setup()" and "usb2_transfer_unsetup()". Set
"ppxfer[n]" when the transfer setup is complete to prevent races. Remove
redundant NULL-checks from "usb2_transfer_unsetup()".
Submitted by: Hans Petter Selasky
- The software computed HID size is not always correct, because the algoritm
does not handle unsorted HID descriptors.
- Change the way we obtain the report ID.
- Use the X/Y/Z+button locations instead for report ID source for ums.
- Add more range checks.
- Remove Microsoft Mouse quirks. If the positions are moduloed the report
length multiplied by 8, the values seem correct.
- Some minor style changes.
Submitted by: Hans Petter Selasky
name) (not sure whether this works correctly, but should be close).
Fix the stub attach phase for some Novatel cards. They expect the CSW
(repsonse to CBW, SCSI eject command) to be fetched before switching to
modem mode.
MFC after: 2 weeks
exceeded the maximum size of 1 page for OHCI controllers. Other serial
drivers use the same size, so I assume this should be enough (1MB/s
throughput?).
heavy loads or working. It looks this bug exists since r158869
so needs to revert a part of the previous.
Reviewed by: imp
Tested by: sam
MFC after: 3 weeks
would fail to attach due to unsupported USB revision. It should have
no effect when running on a real hardware.
Reviewed by: imp
Approved by: rwatson (mentor)
Add support to uscanner.c for known-working devices
(the same should be done for uscanner2.c).
Waiting for 7.1 to be released before the merge.
MFC after: 3 weeks
Note that there is no working backend (or at least
that is mentioned in the PR ticket) but the device
is now supported on our end.
PR: 117205
Submitted by: Artem Naluzhnyy <tut at nhamon dot com dot ua>
MFC after: 1 week
o add EHCI_SCFLG_BIGEMMIO flag to force big-endian byte-select to be
set in USBMODE
o split reset work into new public routine ehci_reset so bus shim drivers
can force big-endian byte-select before ehci_init
o add support to byte swap EHCI descriptor contents; the IXP435
has dual-EHCI controllers integral but descriptor contents are
in big-endian format; this support is configured with the
USB_EHCI_BIG_ENDIAN_DESC option and enabled with EHCI_SCFLG_BIGEDESC
o clean up EHCI USBMODE register setup during init; add #defines for
bit values
o split debug support out into a new file and enable use through ddb
o while here remove a bunch of lingering netbsd-isms
Reviewed by: imp
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
- Bugfix: Don't excede static number of ports allowed when iterating
over endpoints within an interface.
- u3g_speeds contains speeds in baud, not bytes per second, so divide
the buffer size by 10.
patch the RX/TX performance becomes about 17~18 Mbps comparing with
the previous whose values were RX 7~8Mbps and TX 13~14Mbps.
- improve AL2230 RF handling in zd1211b
- support AL2230S RF that PV2000 is renamed to AL2230S
- use register ZYD_CR244, ZYD_CR243, ZYD_CR242 when the driver writes
values on RF. This routine is more faster than the original one
- use private TX lock to avoid LOR at zyd_raw_xmit()
- increase TX slots from 1 to 5
- needs to set the channel at IEEE80211_S_AUTH not IEEE80211_S_RUN
- detailed error handling. In previous the next command was sent to the
device even if there was errors
- setting ZYD_MAC_RX_THRESHOLD value should be different between 1211
and 1211b
- only try to stop the device at zyd_init_locked() if the device is
UPed
- do not use MTX_RECURSE
- do not try to grap Giant lock when the channel is changing
- move the device initialization routines from zyd_attach to zyd_init to
give a device full-reset chance to the driver.
- code cleanup at zyd_raw_xmit()
- simplify zyd_attach() routines
- resort functions and clean up variables
- DPRINTF style change.
- style(9)
Reviewed by: sam
src/sys/dev/usb2/core/usbdevs
src/sys/dev/usb2/include/urio2_ioctl.h
src/sys/dev/usb2/storage/ustorage2_fs.h
These files are not used any more.
src/usr.sbin/Makefile
src/etc/mtree/BSD.include.dist
src/include/Makefile
src/lib/Makefile
src/share/man/man7/hier.7
src/share/mk/bsd.libnames.mk
src/etc/mtree/BSD.include.dist
Make "usbconfig" and "libusb20" a part of the default build.
src/sys/dev/usb/rio500_usb.h
src/sys/dev/usb2/storage/urio2.c
Use common include file.
src/sys/dev/usb2/bluetooth/ng_ubt2.c
Make USB bluetooth depend on "ng_hci" module.
src/sys/dev/usb2/controller/ehci2.c
src/sys/dev/usb2/controller/ehci2.h
Patches for Marvell EHCI.
src/sys/dev/usb2/core/usb2_busdma.c
Bugfix for 64-bit platforms. Need to unload the previously loaded DMA
map and some cleanup regarding some corner cases.
src/sys/dev/usb2/core/usb2_core.h
src/sys/dev/usb2/core/usb2_dev.c
src/sys/dev/usb2/core/usb2_dev.h
Bugfix for libusb filesystem interface.
New feature: Add support for filtering device data at the expense of the
userland process.
Add some more comments.
Some minor code styling.
Remove unused function, usb2_fifo_get_data_next().
Fix an issue about "fifo_index" being used instead of "ep_index".
src/sys/dev/usb2/core/usb2_device.c
src/sys/dev/usb2/core/usb2_generic.c
Bugfix for Linux USB compat layer. Do not free non-generic FIFOs when
doing an alternate setting.
Cleanup USB IOCTL and USB reference handling.
Fix a corner case where USB-FS was left initialised after
setting a new configuration or alternate setting.
src/sys/dev/usb2/core/usb2_hub.c
Improvement: Check all USB HUB ports by default at least one time.
src/sys/dev/usb2/core/usb2_request.c
Bugfix: Make sure destination ASCII string is properly zero terminated
in all cases.
Improvement: Skip invalid characters instead of replacing with a dot.
src/sys/dev/usb2/core/usb2_util.c
src/sys/dev/usb2/image/uscanner2.c
Spelling.
src/sys/dev/usb2/include/Makefile
Share "usbdevs" with the old USB stack.
src/sys/dev/usb2/include/usb2_devid.h
src/sys/dev/usb2/include/usb2_devtable.h
Regenerate files.
Alfred: Please fix the RCS tag at the top.
src/sys/dev/usb2/include/usb2_ioctl.h
Fix compilation of "kdump".
src/sys/dev/usb2/serial/ubsa2.c
src/sys/dev/usb2/serial/ugensa2.c
Remove device ID's which will end up in a new 3G driver.
src/sys/dev/usb2/sound/uaudio2.c
Correct a debug printout.
src/sys/dev/usb2/storage/umass2.c
Sync with old USB stack.
src/lib/libusb20/libusb20.3
Add more documentation.
src/lib/libusb20/libusb20.c
Various bugfixes and improvements.
src/usr.sbin/usbconfig/dump.c
src/usr.sbin/usbconfig/usbconfig.c
New commands for dumping strings and doing custom USB requests from
the command line.
Remove keyword requirements from generated files:
"head/sys/dev/usb2/include/usb2_devid.h"
"head/sys/dev/usb2/include/usb2_devtable.h"
the softc is reset a few times during probing.
Print 'changing to modem mode' messages if booting verbose to show the
reason for the time delay. Note: Some devices (Huawei for one) take 20
seconds to appear on the USB bus).
The same (vendor, product) tuple is used for aue(4) adapters,
but I am not sure if the quirk is correct. I'm using the USB
device 'release' info to skip aue(4) detection right now, but
if there's a better way to differentiate between USB-LAN and
USB Bluetooth we should update the quirk.
Reviewed by: imp, rink
MFC after: 2 weeks
Also: Change the initialisation of the command string to a static
initialiser. Verify it against the output of umass.c when being sent a
command using 'camcontrol eject da0' to a Bulk-Only device.
This should make those devices work that need a SCSI eject command to
switch to modem mode (Novatel 950D and others).
driver (rev 1.3), by Joerg Sonnenberger.
Note: This change is untested as I do not own the hardware. Let me know
if things work or do not work for you by sending me the output dmesg (and
usbctl -f /dev/usbX if possible). Thanks.
in sta and adhoc modes; this should've been done forever ago as most all
drivers use this hook to set per-station transmit parameters such as for
tx rate control
o adjust drivers to remove explicit calls to the driver newassoc method
might make Qualcomm and Option cards (which have all endpoints in 1
interface) work.
- Change the USB buffer sizes to depend on the transfer speed. With UMTS
we use a buffer 384k / 1000 frames/sec * 50msecs =~ 15kB for example.
- Add a MODULE_VERSION statement
the Sierra and Novatel devices, ignore all umass devices and hide the umass
devices that represent the CD ROM devices (but not the SD card slot in the
Huawei Mobile dongle).
Note: This driver in FBSD7 seems to suffer from memory corruption when used
with an Option GT Quad. The E220 however works flawlessly.
Also add the ID for the Option GTMaxHSUPA, provided by Olivier Fromme.
example the Huawei Mobile has an SD card slot on the second interface.
- Do not attach to Qualcomm and Novatel cards. If ignored these cards will
switch to modem mode automatically it seems.
- Reduce the priority on generic attachment to the appropriate level.
Note: A better solution is to send an eject command straightaway, but that can
be left till later.
This was located in the ubsa driver, but should be moved into a separate
driver:
- 3G modems provide multiple serial ports to allow AT commands while the PPP
connection is up.
- 3G modems do not provide baud rate or other serial port settings.
- Huawei cards need specific initialisation.
- ubsa is for Belkin adapters, an Linuxy choice for another device like 3G.
Speeds achieved here with a weak signal at best is ~40kb/s (UMTS). No spooky
STALLED messages as well.
Next: Move over all entries for Sierra and Novatel cards once I have found
testers, and implemented serial port enumeration for Sierra (or rather have
Andrea Guzzo do it). They list all endpoints in 1 iface instead of 4 ifaces.
Submitted by: aguzzo@anywi.com
MFC after: 3 weeks
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
Kick the device into the right mode if it comes up as a flash-disk.
Set the buffers to a sensible 1024 bytes instead of a far too small
default.
Don't attempt to change speed, baud, parity and such, the device does
not understand it.
this also can be happened if we pull the USN stick out forcibly.
Currently the ZyDAS driver uses tsleep() when it try to query a read
command to the device and it'd make a timeout if the device doesn't
response within about 1 sec.
In a case of that the USB stick is gone by hand and the driver's
scanning with changing the channel numbers, the thread which is sleeping
until a command requested is responded can be waked up after all
detaching routines finished that means the zyd softc already freed.
Tring to touch the softc freed by the wakeup thread makes a panic.
So make sure that all sleeping threads should be waken up before the
detach is completed and any other new requests to the device should be
prevented.
detaching that when the USB is pulled out forcibly during the driver is
running background scan, a page fault can be occurred even if we called
usb_rem_task() when detaching. It looks like a kind of races.
the device indicates that it wasn't able to write all the data in the
buffer out.
Ed Schouten doesn't like the idea of a panic here. I think for
production code, we need something better. For right now, while we're
trying to assess the impact of this issue, a panic is OK. So complain
to me, not him if this is hit.
from umodem and ufoma.
With these changes, umodem kinda works for me now. It certainly gets
past the "tip" bug that I found earlier where 115200 wasn't a valid
baud rate. This was "broken" in the mpsafetty commit, but in reality,
umodem was always broken.
taken from PR/121184 which was mechanically generated from similar
lists in the Linux ipaq driver. I then took the numbers we had in
usbdevs and filled in the right symbols and eliminated duplicates.
PR: 121184
The last half year I've been working on a replacement TTY layer for the
FreeBSD kernel. The new TTY layer was designed to improve the following:
- Improved driver model:
The old TTY layer has a driver model that is not abstract enough to
make it friendly to use. A good example is the output path, where the
device drivers directly access the output buffers. This means that an
in-kernel PPP implementation must always convert network buffers into
TTY buffers.
If a PPP implementation would be built on top of the new TTY layer
(still needs a hooks layer, though), it would allow the PPP
implementation to directly hand the data to the TTY driver.
- Improved hotplugging:
With the old TTY layer, it isn't entirely safe to destroy TTY's from
the system. This implementation has a two-step destructing design,
where the driver first abandons the TTY. After all threads have left
the TTY, the TTY layer calls a routine in the driver, which can be
used to free resources (unit numbers, etc).
The pts(4) driver also implements this feature, which means
posix_openpt() will now return PTY's that are created on the fly.
- Improved performance:
One of the major improvements is the per-TTY mutex, which is expected
to improve scalability when compared to the old Giant locking.
Another change is the unbuffered copying to userspace, which is both
used on TTY device nodes and PTY masters.
Upgrading should be quite straightforward. Unlike previous versions,
existing kernel configuration files do not need to be changed, except
when they reference device drivers that are listed in UPDATING.
Obtained from: //depot/projects/mpsafetty/...
Approved by: philip (ex-mentor)
Discussed: on the lists, at BSDCan, at the DevSummit
Sponsored by: Snow B.V., the Netherlands
dcons(4) fixed by: kan
corresponding USAGE should be skipped as well.
For example, below is a report desc fragment of some mouse:
COLLECTION
...
USAGE TWHEEL
FEATURE ...
...
USAGE WHEEL
INPUT ...
...
END COLLECTION
"USAGE TWHEEL" should be consumed after the FEATURE item is skipped,
otherwise, the INPUT item will be assigned to "USAGE TWHEEL" later,
other than "USAGE WHEEL".
Tested by: Grzegorz Blach
PR: usb/125941
This driver supports GW3887 based chipsets and works on
x86/powerpc/sparc64. You need upgtfw kernel module before loading
upgt(4). Please see the manpage.
Obtained from: OpenBSD
The kbd, kbdmux, ugen and uhid drivers included <sys/tty.h>, because
they needed clists, which have been moved to <sys/clist.h> some time
ago. In the MPSAFE TTY branch, <sys/tty.h> does not include
<sys/clist.h>, which means we have to teach these drivers to include
this header file directly.
Approved by: philip (mentor, implicit)
dispatched without Giant, and add NETISR_FORCEQUEUE, which allows specific
netisr handlers to always be dispatched via a queue (deferred). Mark the
usb and if_ppp netisr handlers as NETISR_FORCEQUEUE, and explicitly
acquire Giant in those handlers.
Previously, any netisr handler not marked NETISR_MPSAFE would necessarily
run deferred and with Giant acquired. This change removes Giant
scaffolding from the netisr infrastructure, but NETISR_FORCEQUEUE allows
non-MPSAFE handlers to continue to force deferred dispatch so as to avoid
lock order reversals between their acqusition of Giant and any calling
context.
It is likely we will be able to remove NETISR_FORCEQUEUE once
IFF_NEEDSGIANT is removed, as non-MPSAFE usb and if_ppp drivers will no
longer be supported.
Reviewed by: bz
MFC after: 1 month
X-MFC note: We can't remove NETISR_MPSAFE from stable/7 for KPI reasons,
but the rest can go back.
Remove the code which disables port status change interrupts for 1s
when one occured -- this makes that events get lost or delayed until
the next change.
Obtained from: NetBSD
some longstanding issues:
o pass the vap since it's now the "coin of the realm" and required
to do things like set initial tx parameters in private node
state for use prior to association
o pass the mac address as cards that maintain outboard station
tables require this to create an entry (e.g. in ibss mode)
o remove the node table reference, we only have one node table
and it's unlikely this will change so this is not needed to
find the com structure
