hook it up to ada(4) also. While at it, rename *ad_firmware_geom_adjust()
to *ata_disk_firmware_geom_adjust() etc now that these are no longer
limited to ad(4).
Reviewed by: mav
MFC after: 3 days
When not defining header split do not allocate mbufs,
this can be a BIG savings in the mbuf memory pool.
Also keep seperate dma maps for the header and
payload pieces when doing header split. The basis
of this code was a patch done a while ago by
yongari, thank you :)
A number of white space changes.
MFC: in a few days
free(9) and it can cause kernel panic when there are multiple graphics
controllers in the system.
Tested by: Brandon Gooch (jamesbrandongooch at gmail dot com)
MFC after: 3 days
firmware in order to take over control of the SMU. Without doing this,
the firmware background process doing fan control will run amok as we
take over the system and crash the management chip.
This is limited to these two machines because our kernel is heavily
dependent on firmware accesses, and so quiescing firmware can cause
nasty problems.
Powermac G5 systems. MSI and several other things are not presently
supported.
The U3/U4 internal device support portions of this change were contributed
by Andreas Tobler.
MFC after: 1 week
so ni_txrate returned 0 which is a invalid result.
- The fourth argument of ieee80211_ratectl_tx_complete() could be not
NULL.
Reported by: Gustau P?rez <gperez at entel.upc.edu>
Tested by: Gustau P?rez <gperez at entel.upc.edu>,
Ian FREISLICH <ianf at clue.co.za>
MFC after: 3 days
- add a moderation value to the Link vector
- allow disabling HW RSC on the 82599 if LRO
is not enabled.
- correct error in the stats code
- change optic type on the 82598 DA device
Thanks to Andrew Boyer for the changes.
RFA. Also drop frames that have either CRC error or alignment
error. Normally bad frames are not received at all. But controllers
running in promiscuous mode will receive bad frames. 82557 will
also receive bad frames to receive VLAN oversized frames.
While I'm here mark RNR condition if driver happen to see RNR in
RFA status and restart RU to receive frames again. Because driver
checks all received frames in RX loop, RNR condition could be set
in the middle of RX processing. Just relying on RNR interrupt was
not enough.
This change fixes "Memory modified after free" issue when fxp(4)
is running as a member of if_bridge(4).
Tested by: Larry Baird <lab <> gta dot com>
MFC after: 5 days
microframe slot was not in the smask. The problem was that the EHCI driver was
then thinking that the transfer was immediately complete in some cases. Which
could lead to freeze-like situations, which can be recovered by unplugging the
USB device.
Reported by: Richard Kolkovich
Submitted by: Hans Petter Selasky
USB enumeration lock is locked, then the USB stack fails to resume the device
because locking the USB enumeration lock is part of the resume procedure. To
solve this issue a new lock is introduced which only protects the suspend and
resume callbacks, which can be dropped inside the usbd_do_request_flags()
function, to allow suspend and resume during so-called enumeration operations.
Submitted by: Hans Petter Selasky
hardware tag insertion/stripping. Remove conditional code that
disables these hardware features on SiS190. Also nuke RX fixup code
which is no more required on strict-alignment architectures because
SiS190 supports RX 10 bytes padding.
Now all hardware features except jumbo frame and WOL are supported.
Thanks to Masa Murayama who confirmed SiS190 also has the same
hardware features of SiS191.
I guess the only difference between SiS191 and SiS190 would be
jumbo frame support. It will be implemented in near future.
fragmentation of mbuf chain to 32 from 16 because TSO can send 64KB
sized packet which in turn requires long list of mbuf chain. Due to
lack of documentation, I'm not sure whether driver have to pull up
ethernet/IP/TCP header with options to make controller work but
driver have to parse TCP header to update pseudo TCP checksum
anyway. The controller expects pseudo TCP checksum computed by
upper stack and the checksum should follow the MS NDIS
specification to make TSO work.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
fxp(4) already used to extract most hardware MAC statistics but it
didn't show them. With this change, all MAC statistics counters
are exported. Because there are a couple of new counters for 82558
and 82559, enable extended MAC statistics functionality to get
these counters. Accoring to public data sheet, 82559 MAC statistics
return 24 DWORD counters(3 counters are unknown at this moment) so
increase MAC counter structure to meet the MAC statistics block size.
The completion of MAC counter dump is now checked against
FXP_STATS_DR_COMPLETE status code which is appended at the end of
status block. Previously fxp(4) ignored the status of the
FXP_SCB_COMMAND_CU_DUMPRESET command. fxp(4) does not wait for the
completion of pending command before issuing
FXP_SCB_COMMAND_CU_DUMPRESET. Instead it skips the command and try
it next time. This scheme may show better performance but there is
chance to loose updated counters after stopping controller. So make
sure to update MAC statistics in fxp_stop().
While I'm here move sysctl node creation to fxp_sysctl_node().
Tested by: Larry Baird < lab <> gta dot com >
table. The default size of the configuration table was 22 bytes. To
use extended feature of 82550/82551 the configuration table size
was expanded to 32 bytes. The added configuration for 82550/82551
specifies VLAN hardware tagging and IPSec configuration as well as
TCO.
To make configuration easier fxp(4) used a configuration template
and the template was copied to configuration table. After that,
some parameters of the configuration table was changed depending on
controller type and operation mode. However the size of template
was 22 bytes so some configuration parameters were not properly
initialized on 82550/82551.
Fix this by increasing the template size. For 82557, 82558 and
82559 the size of the configuration is still 22 bytes.
unicast and the other for multicast. To receive multicast frames
that host didn't join in promiscuous mode, driver have to set
promiscuous mode for multicast frames as well.
The Open Source Software Developer Manual for i8255x was not clear
how to handle promiscuous mode.
PR: kern/145905
MFC after: 5 days
from passive to active scans. Basicly disable it by increasing the
amount packets to be received to an amount which can't be reached
during dwell times.
Approved by: rpaulo (mentor)
MFC after: 3 days
L2/3/4 headers and can drop or steer packets as instructed. Filtering
based on src ip, dst ip, src port, dst port, 802.1q, udp/tcp, and mac
addr is possible. Add support in cxgbtool to program these filters.
Some simple examples:
Drop all tcp/80 traffic coming from the subnet specified.
# cxgbtool cxgb2 filter 0 sip 192.168.1.0/24 dport 80 type tcp action drop
Steer all incoming UDP traffic to qset 0.
# cxgbtool cxgb2 filter 1 type udp queue 0 action pass
Steer all tcp traffic from 192.168.1.1 to qset 1.
# cxgbtool cxgb2 filter 2 sip 192.168.1.1 type tcp queue 1 action pass
Drop fragments.
# cxgbtool cxgb2 filter 3 type frag action drop
List all filters.
# cxgbtool cxgb2 filter list
index SIP DIP sport dport VLAN PRI P/MAC type Q
0 192.168.1.0/24 0.0.0.0 * 80 0 0/1 */* tcp -
1 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* udp 0
2 192.168.1.1/32 0.0.0.0 * * 0 0/1 */* tcp 1
3 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* frag -
16367 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* * *
MFC after: 2 weeks
is no more need to defragment mbufs. After transmitting the
multi-fragmented frame, the controller updates only the first
descriptor of multi-descriptor transmission so it's driver's
responsibility to clear OWN bits of remaining descriptor of
multi-descriptor transmission. It seems the controller behaves much
like jme(4) controllers in descriptor handling.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
received frames. Also check driver has valid ifp pointer before
calling msk_stop() in device_shutdown handler. While I'm here
remove unnecessary accesses to interrupt mask registers in
device_shutdown handler because driver puts the controller into
reset state.
With these changes, msk(4) now survive from heavy RX traffic(1byte
UDP frame) while reboot is in progress.
Reported by: Mark Atkinson < atkin901 <> gmail dot com >
by zero of the second argument 'from'.
- Prefer u_int32_t over unsigned int to make its intention more clearer.
- Move the function to a header file and make it a static inline function.
Pointed out by: Andrew Reilly (areilly at bigpond dot net dot au)[1]
MFC after: 3 days
on Cassini using the external PCS SERDES otherwise unaligned access
traps and other strange effects happen with some machines. Don't touch
the MIF which is unused in that case either. These changes require the
PHY type to use to be determined via the OFW device tree or from the
VPD in machines without the former.
- Disable the SERDES pins of Saturn when not used in order to save power
and ensure they are enabled otherwise.
- In cas_attach() use the correct register offset for CAS_PCS_CONF_EN.
- Add some bus space barriers missing in the PCS code path.
These changes make the Sun GigaSwift Ethernet 1.0 MMF cards as well as
the on-board interfaces found in Sun Fire B100s Blade Server work.
PR: 144867
scope of the object lock in agp_i810.c. (In this specific case, the scope
of the object lock shouldn't matter, but I don't want to create a bad
example that might be copied to a case where it did matter.)
Reviewed by: kib
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
driver for CAM ATA subsystem. This driver supports same hardware as
atamarvell, ataadaptec and atamvsata drivers from ata(4), but provides
many additional features, such as NCQ, PMP, etc.
- device initiated power management (some devices support only this way);
- Automatic Partial to Slumber Transition (more power saving);
- DMA auto-activation (expected to slightly improve performance).
More features could be added later, when hardware supports.
This bug would cause allocating sample-mode PMCs to fail with ENOMEM after allocating several counting-mode PMCs.
Approved by: jkoshy (mentor)
MFC after: 2 weeks
that generates a fatal bus trap. Normally, the chips are setup to do
128 byte DMA bursts, but when on this CPU, they can only safely due
4-byte DMA bursts due to this bug. Details of the exact nature of the
bug are sketchy, but some can be found at
https://forum.openwrt.org/viewtopic.php?pid=70060 on pages 4, 5 and 6.
There's a small performance penalty associated with this workaround,
so it is only enabled when needed on the Atheros AR71xx platforms.
Unfortunately, this condition is impossible to detect at runtime
without MIPS specific ifdefs. Rather than cast an overly-broad net
like Linux/OpenWRT dues (which enables this workaround all the time on
MIPS32 platforms), we put this option in the kernel for just the
affected machines. Sam didn't like this aspect of the patch when he
reviewed it, and I'd love to hear sane proposals on how to fix it :)
Reviewed by: sam@
does. Without this change, Yukon Extreme seems to generate lots of
RX FIFO overruns even though controller has available RX buffers.
These excessive RX FIFO overruns generated lots of pause frames
which in turn killed devices plugged into switch. It seems there is
still occasional RX frame corruption on Yukon Extreme but this
change seems to fix the pause frame storm.
Reported by: jhb
Tested by: jhb
MFC after: 5 days
- Print device details only when verbose boot is enabled.
- Add debug output for shared memory access.
- Add debug statistics (checksum offload & VLAN frame counters).
- Modify TX path to update consumer index for each frame completed
rather than updating the consumer index only once for a group of
frames to improve small packet performance.
- Print driver/firmware pulse messages only when verbose boot
is enabled.
- Add debug sysctl to clear statistics.
- Fix more style(9) violations.
MFC after: 2 weeks
architecture from page queue lock to a hashed array of page locks
(based on a patch by Jeff Roberson), I've implemented page lock
support in the MI code and have only moved vm_page's hold_count
out from under page queue mutex to page lock. This changes
pmap_extract_and_hold on all pmaps.
Supported by: Bitgravity Inc.
Discussed with: alc, jeffr, and kib
controller, I'm not sure whether this is also applicable to SiS190
so this feature is only activated on SiS191 controller.
In theory, controller reinitialization is not needed when VLAN tag
configuration is changed, but xclin said controller was not stable
whenever toggling VLAN tag bit. To address that, sge(4)
reinitialize controller for VLAN configuration which seems to work
as expected. VLAN tag information for TX/RX descriptor and
configure bit of RxMacControl register was found by xclin.
Submitted by: xclin <xclin <> cs dot nctu dot edu dot tw > (initial version)
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
register. Due to lack of SiS190 controller, I'm not sure whether
this is also applicable to SiS190 so this feature is only activated
on SiS191 controller.
The controller can pad 10 bytes before DMAing a received frame to
RX buffer and received bytes include the padded bytes. This padding
is very useful on strict-alignment architectures because driver
does not have to copy received frame to align IP header on 4 bytes
boundary. It also gives better RX performance on non-strict
alignment architectures. Special thanks to xclin to give me
valuable register information. Without his enthusiastic trial and
errors this wouldn't be even possible.
While I'm here tighten validity check of received frame. Controller
clears RDS_CRCOK bit when it received bad CRC frames. xclin found
that using loop back testing.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
programs RX filter configuration. It seems RX MAC control register
is one of key registers to get various offloading features as well
as performance. Blindly clearing unrelated bits can result in
unexpected results.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
emulated by BIOS using SMI interrupt. On those chipsets reading
from the status port may be thousand times slower than usually.
Sometimes this emilation is not working properly resulting in
commands timing out and since we assume that inb() operation
takes very little time to complete we need to adjust number of
retries to keep waiting time within a designed limits (100ms).
Measure time it takes to make read_status() call and adjust
number of retries accordingly.
To keep it simple, use TSC to measure inb() performance and
keep it to amd64-only, since TSC may not available on older
CPUs.
Also enable detection of the AT controller absence on amd64.
Reviewed by: jhb
MFC after: 1 month
back in rxeof (I could see little point in taking it out),
and now release it before the stack entry.
Also, make it so the 82574 does not configure for multiqueue
when its not used in the stack.
On top of that, LLVM+Clang mis-compiles this code because of its register
allocator bug.
Analyzed by: Andrew Reilly (areilly at bigpond dot net dot au)
Reviewed by: ariff, rdivacky
MFC after: 3 days
In the end, it does help fixing /dev/io usage from multithreaded
processes.
- On i386 and amd64 the old behaviour is kept but multithreaded
processes must use the new interface in order to work well.
- Support for the other architectures is greatly improved, where
necessary, by the necessity to define very small things now.
Manpage update will happen shortly.
Sponsored by: Sandvine Incorporated
PR: threads/116181
Reviewed by: emaste, marcel
MFC after: 3 weeks
Open Firmware device tree in order to match what the PROM built-in
driver uses. This is especially important when netbooting Fujitsu
Siemens PRIMEPOWER250 as in that case the built-in driver isn't used
and the port facts PortSCSIID defaults to 0, conflicting with the
disk at the same address.
first descriptor in TSO case. Otherwise controller can generate bad
frames during TSO. To address it, make sure to pull up ethernet +
IP + TCP header with options in first buffer. Also ensure the
buffer length of the first descriptor for TSO covers entire ethernet
+ IP + TCP with options and setup additional Tx descriptor if the
first buffer includes TCP payload.
Tested by: Amar Takhar <verm <> darkbeer dot org >
MFC after: 1 week
Some of these cases should be safe in a non-atomic fashion, however
since all of the driver ioctls are locked, a lot of work is required to
fix it correctly. Just don't sleep now.
MFC after: 2 weeks
was chosen by lots of trial and errors. The chosen value shows
good interrupt moderation without additional latency.
Without this change, controller can generate more than 140k
interrupts per second under high network load.
Submitted by: xclin <xclin <> cs dot nctu dot edu dot tw >
This time, abandon the use of busdma and start interacting with the VM
system directly. Make use of the new kmem_alloc_attr() which allows us
to easily allocate non-contiguous pages to back the GART table. This
should help a lot when starting or restarting X after the system has
been running for a while and memory has become fragmented.
MFC after: 2 weeks
* On 32 bit platforms we steal the upper 4 bits of the map handle
to store a unique map id.
* On 64 bit platforms we steal the upper 24 bits.
Resolves issues where the offsets that are handed to mmap may overlap the VRAM on some cards.
Tested on: radeon, intel, mga, and via.
This will break nouveau. I will spin new patches shortly.
proper device_t so it faked the devctl event to appear like one, this is now a
notify which allows more information to be passed.
We notify for both the device attach/detach and for each usb interface. A devd
rule can now match on the interface properties, including composite devices
which may have a uvideo interface and also usound and possibly uhid too.
An example to match a umass device with a scsi subclass and BBB protocol would be
notify 100 {
match "system" "USB";
match "subsystem" "INTERFACE";
match "type" "ATTACH";
match "intclass" "0x08";
match "intsubclass" "0x06";
match "intprotocol" "0x50";
action ...
};
The old attach devctl event has been retained for the moment to make merging to
8.1 easier. This was never compatible with 7.x or earlier due to the ugen regex
change needed.
Reviewed by: warner
MFC after: 1 week
occurs. In addition, the delay when programming the short cable fix
should be 100us, not 100ms.
PR: kern/64556
Submitted by: Thomas Hurst <tom at hur.st>
Approved by: rrs (mentor)
MFC after: 1 week
no flowid is present, this was causing some bad
reordering, now just use 0.
Also, add a few watchdog bits, and tx handler bits
that were corrected in igb.
- Re-probe xfp / sfp+ socket on link events, in case user
has changed transceiver
- correctly report current media to avoid confusing lagg (reported by Panasas)
- Report link speed (submitted by yongari)
Reviewed by: yongari (earlier version)
MFC after: 7 days
This driver was written by Alexander Pohoyda and greatly enhanced
by Nikolay Denev. I don't have these hardwares but this driver was
tested by Nikolay Denev and xclin.
Because SiS didn't release data sheet for this controller, programming
information came from Linux driver and OpenSolaris. Unlike other open
source driver for SiS190/191, sge(4) takes full advantage of TX/RX
checksum offloading and does not require additional copy operation in
RX handler.
The controller seems to have advanced offloading features like VLAN
hardware tag insertion/stripping, TCP segmentation offload(TSO) as
well as jumbo frame support but these features are not available
yet. Special thanks to xclin <xclin<> cs dot nctu dot edu dot tw>
who sent fix for receiving VLAN oversized frames.
unneeded for legacy hardware.
Also remove some TSO related cruft.
Add some watchdog_time setting that was missing, thanks
to Mikolaj Golub for pointing that out.
* WPA-None requires ap_scan=2:
The major difference between ap_scan=1 (default) and 2 is, that no
IEEE80211_IOC_SCAN* ioctls/functions are called, though, there is a
dependency on those. For example the call to wpa_driver_bsd_scan()
sets the interface UP, this never happens, therefore the interface
must be marked up in wpa_driver_bsd_associate(). IEEE80211_IOC_SSID
also is not called, which means that the SSID has not been set prior
to the IEEE80211_MLME_ASSOC call.
* WPA-None has no support for sequence number updates, it doesn't make
sense to check for replay violations..
* I had some crashes right after the switch to RUN state, issue is
that sc->sc_lastrs was not yet defined.
Approved by: rpaulo (mentor)
MFC after: 3 weeks
StarCat systems which provides time-of-day services for both as well as
console service for Serengeti, i.e. Sun Fire V1280. While the latter is
described with a device type of serial in the OFW device tree, it isn't
actually an UART. Nevertheless the console service is handled by uart(4)
as this allowed to re-use quite a bit of MD and MI code. Actually, this
idea is stolen from Linux which interfaces the sun4v hypervisor console
with the Linux counterpart of uart(4).
set, it make sense to actually initialize that array. This fixes some
issues with 4965 adapters where the TX power is crucial.
This got lost somewhere while merging with the OpenBSD code.
Approved by: rpaulo (mentor)
Obtained from: OpenBSD
MFC after: 2 weeks
* Enable DC calibration and crystal calibration on Centrino Advanced-N
6250 parts.
* Workaround for a HW bug (does not affect 4965AGN) that may sporadically
affect latency under some rare circumstances. From a similar commit to
iwlwifi.
* Update sensitivity settings for 5000 series to workaround a performance
bug in the DSP (1000 is not affected so we keep the old values for 5000).
* Update sensitivity settings for 6000 series.
* Set differential gains on 6250 too (but use a 1.0 factor, not 1.5).
* Init OFDM sensitivity with min value (which depends on the chip)
instead of hardcoding it to 90.
* Read calibration version from ROM and set IWN_GP_DRIVER_CALIB_VER6
bit on 6x50 if version >= 6.
Approved by: rpaulo (mentor)
Obtained from: OpenBSD
MFC after: 2 weeks
- code flow in handler could let interrupt be
reenabled when not wanted.
- change where the RX lock is taken to improve
performance.
- adapter->msix is true for MSI systems also,
it needs to explicitly test for 82574, good one :)
- add CRC stripping to the RX side, this was handled
by some obscure code in rxeof previously, its easier
to simply have the hardware strip it now.
- Add back an ALTQ change that slipped between the cracks
- Add an update to the watchdog_time in the xmit code, not
doing this in ixgbe caused problems, think its needed here
as well.
VLAN HWFILTER from being used by default, this breaks
stacked pseudo devices, and as it turns out, also breaks
virtual machines that happen to use VLANS (didn't know that
before :). Put the fix back into the em driver, and for good
measure add the same code to the igb driver where it should
have been anyway.
Just relying on status LE ownership of status block seems to cause
poor performance. Always read current status index register first
and then check status ownership as we had before. Accessing status
index register seems to trigger immediate status update if
controller have pending status updates.
MFC after: 1 week
Reported by: Andre Albsmeier <Andre.Albsmeier <> siemens dot com>
Tested by: Andre Albsmeier <Andre.Albsmeier <> siemens dot com>
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
- Added some new debug helper routines to systcl.
- Fixed many of the style(9) violations that have crept into the code
due to my use of a "smart" editor.
MFC after: 2 weeks
set to sane values as they no longer default to 0, otherwise some OFW
implementation might copy in or out arguments not based on what the actual
function takes but what ever stack garbage nargs and nreturns supply.
Reviewed by: nwhitehorn
domain clock, 8 programmable PMC.
- Westmere based CPU (Xeon 5600, Corei7 980X) support.
- New man pages with events list for core and uncore.
- Updated Corei7 events with Intel 253669-033US December 2009 doc.
There is some removed events in the documentation, they have been
kept in the code but documented in the man page as obsolete.
- Offcore response events can be setup with rsp token.
Sponsored by: NETASQ
volumes were incorrectly calculated.
I've tested this with one of my es1370 cards and I can confirm that it
works.
PR: 98167
Submitted by: Joseph Terner <jtsn@gmx.de>
Approved by: kib
change the argument type to igb_rxeof() to the
correct type. Note, any users of POLLING must
be sure and set the number of queues to 1 for
things to work correctly.
- Only the tunnelq (TXQ_ETH) requires a buf_ring, an ifq, and the watchdog/timer
callouts. Do not allocate these for the other tx queues.
- Use 16k jumbo clusters only on offload capable cards by default.
- Do not allocate a full tx ring for the offload queue if the card is not
offload capable.
- Slightly better freelist size calculation.
- Fix nmbjumbo4 typo, remove unneeded global variables.
MFC after: 3 days
also for finding a one character bug that kept TSO from working.
Sometimes with direct attach cables a failure can occur in init,
the old method of calling detach was broken, there is no way to
return an error to the system from init, so I have changed it to
return failure thru the ioctl.
And, have fixed the ALTQ code changes of Max Laier, sorry Max :)
em revision 7.0.0:
- Using driver devclass, seperate legacy (pre-pcie) code
into a seperate source file. This will at least help
protect against regression issues. It compiles along
with em, and is transparent to end use, devices in each
appear to be 'emX'. When using em in a modular form this
also allows the legacy stuff to be defined out.
- Add tx and rx rings as in igb, in the 82574 this becomes
actual multiqueue for the first time (2 queues) while in
other PCIE adapters its just make code cleaner.
- Add RX mbuf handling logic that matches igb, this will
eliminate packet drops due to temporary mbuf shortage.
igb revision 1.9.3:
- Following the ixgbe code, use a new approach in what
was called 'get_buf', the routine now has been made
independent of rxeof, it now does the update to the
engine TDT register, this design allows temporary
mbuf resources to become non-critical, not requiring
a packet to be discarded, instead it just returns and
does not increment the tail pointer.
- With the above change it was also unnecessary to keep
'spare' maps around, since we do not have the discard
issue.
- Performance tweaks and improvements to the code also.
MFC in a week
- add some new hardware support for 82599
- Big change to interrupt architecture, it now
uses a queue which contains an RX/TX pair as
the recipient of the interrupt. This will reduce
overall system interrupts/msix usage.
- Improved RX mbuf handling: the old get_buf routine
is no longer synchronized with rxeof, this allows
the elimination of packet discards due to mbuf
allocation failure.
- Much simplified and improved AIM code, it now
happens in the queue interrupt context and takes
into account both the traffic on the RX AND TX
side.
- variety of small tweaks, like ring size, that have
been seen as performance improvements.
- Thanks to those that provided feedback or suggested
changes, I hope I've caught all of them.
on debug output. Add a new platform function requirement to allow
for printing based upon the ITL nexus instead of the isp unit plus
channel, target and lun. This allows some printouts and error messages
from the core code to appear in the same format as the platform's
subsystem (in FreeBSD's case, CAM path).
MFC after: 1 week
First, we compare mode table data against minimum value. If the mode table
does not make sense, we set the minimum in the mode info. When we actually
set the mode, we try VESA BIOS function and compare it against the previous
value. If it makes more sense, update the information.
Andrew Turner. The kernel supports the LN2410SBC evaluation board,
and likely others. These parts (or similar ones) are in some open
hardware designs for phones.
Submitted by: Andrew Turner
- Don't leak slice resources when mxge_alloc_rings() fails
- Start taskq threads only after we know attach will succeed. At
boot time, taskqueue_terminate() will loop infinately, waiting
for the threads to exit, and hang the system.
Submitted by: Panasas
MFC After: 3 days
Untangle some of the confusion about what role means when it's in the FCPARAM/SDPARAM
or isp_fc/isp_spi structures. This fixed a problem about seeing targets appear if you've
turned off autologin and find them, or rather don't, via camcontrol rescan.
MFC after: 1 month
configuration space on Yukon Ultra(88E8056) such that accesses to
these registers were NOPs which in turn make msk(4) instable on
this controller. Use indirect access method to access
PCI_OUR_REG_[1-5] registers. This should fix a long standing
instability bug which prevented msk(4) working on Yukon Ultra.
Special thanks to koitsu who gave me remote access to his system.
PR: kern/114631, kern/116853
MFC after: 1 week
arcconf tool by Adaptec already seems to use for identifying the
Serial Number of the devices.
Some simple things (like FIB setup and bound checks) are retrieved
from the Adaptec's driver, but this implementation is quite different
because it does use the normal buffer dmat area for loading segments
and not a special one (like the Adaptec's one does).
Sponsored by: Sandvine Incorporated
Discussed with: emaste, scottl
Reviewed by: emaste, scottl
MFC: 2 weeks
have the delayed function take an argument as to the offset
to the SCTP header. This allows it to work for V4 and V6.
This of course means changing all callers of the function
to either pass the header len, if they have it, or create
it (ip_hl << 2 or sizeof(ip6_hdr)).
PR: 144529
MFC after: 2 weeks
Yukon FE and Yukon Ultra2. These controllers provide very simple
checksum computation mechanism and it requires additional pseudo
header checksum computation in upper stack. Even though I couldn't
see much performance difference with/without Rx checksum offloading
it may help notebook based controllers.
Actually controller can compute two checksum value by giving
different starting position of checksum computation on received
frame. However, for long time, Marvell's checksum offloading engine
have been known to have several silicon bugs so don't blindly trust
computed partial checksum value. Instead, compute partial checksum
twice by giving the same checksum computation position and compare
the result. If the value is different it's clear indication of
hardware bug. This configuration lose IP checksum offloading
capability but I think it's better to take safe route.
Note, Rx checksum offloading for Yukon XL was still disabled due to
known silicon bug.
index of status block is read first before acknowledging the
interrupts. Otherwise bge(4) may get stale status block as
acknowledging an interrupt may yield another status block update.
Reviewed by: marius
is issued at the beginning of the initial IN/OUT data transfers. Reason
unknown, probably firmware fault. Now the stall is only cleared on data
transfer errors.
PR: usb/144199
Submitted by: Hans Petter Selasky
other modules can generate USB descriptors.
- extend the vendor specific request function by one length pointer argument,
because not all descriptors store the length in the first byte. For example
HID descriptors.
Submitted by: Hans Petter Selasky
Also disable relaxed ordering as recommended by data sheet for
PCI-X devices. For PCI-X BCM5704, set maximum outstanding split
transactions to 0 as indicated by data sheet.
For BCM5703 in PCI-X mode, DMA read watermark should be less than
or equal to maximum read byte count configuration. Enforce this
limitation in DMA read watermark configuration.
chip revision often found in the blades and resulting in interfaces
not sensing carrier signal. Looking at all problem reports it
appears that it only affects some very specific silicon revision
(ASIC (0x57081021); Rev (B2)) and version of the PHY that
supports 1000baseSX-FDX media only. Therefore, narrow the scope of
workaround to combination of that revision and media type. Given
that the first report on this issue is dated back to 2007, there is
not much hope that this issue will ever be properly resolved.
Among affected systems are IBM HS21, Intel SBXD132 and HP BL460c.
PR: 118238, 122551, 140970
MFC after: 1 month
are referenced directly from ivar pointer. It's to do like what other
buses do. [1]
o changes exported prototypes. It doesn't use struct siba_* structures
anymore that instead of it it uses only device_t.
o removes duplicate code and debug messages.
o style(9)
Pointed out by: imp [1]
Setting the new sysctl MIB "debug.acpi.enable_debug_objects" to a non-zero
value enables us to print Debug object when something is written to it.
- Allow users to disable interpreter slack mode. Setting the new tunable
"debug.acpi.interpreter_slack" to zero disables some workarounds for common
BIOS mistakes and enables strict ACPI implementations by the specification.
pmc_flush_logfile is now non-blocking and just ask the kernel
to shutdown the file. From that point, no more data is
accepted by the log thread and when the last buffer is flushed
the file is closed.
This will remove a deadlock between pmcstat asking for
flush while it cannot flush the pipe itself.
MFC after: 3 days
interface didn't be attached automatically at boot time so changes a
approach to attach children based on leveraging some newbus niceties.
Submitted by: nwhitehorn
- change the way in which command queue overflow is handled;
- do not expose to CAM two command slots, used for driver's internal purposes;
- allow driver to use up to 1024 command slots, instead of 256 before.
88E1149 PHY. This will fix intermittent watchdog timeouts as well
as very slow network performance on 88E8072 Yukon Extreme.
PR: kern/144148
MFC after: 1 week
o rename the new variables to comply with the naming scheme
o move the new variables to an AR5212 specific struct
o use ahp when available
o revert to previous ts_flags check
does not generate excessive interrupts any more so we don't need
to have two copies of interrupt handler.
While I'm here remove two STAT_PUT_IDX register accesses in LE
status event handler. After r204539 msk(4) always sync status LEs
so there is no need to resort to reading STAT_PUT_IDX register to
know the end of status LE processing. Just trust status LE's
ownership bit.
countdown timer register. The timer resolution may vary among
controllers but the value would be represented by core clock
cycles. msk(4) will automatically computes number of required clock
cycles from given micro-seconds unit.
The default interrupt holdoff timer value is 100us which will
ensure less than 10k interrupts under load. The timer value can be
changed with dev.mskc.0.int_holdoff sysctl node.
Note, the interrupt moderation is shared resource on dual-port
controllers so you can't use separate interrupt moderation value
for each port. This means we can't stop interrupt moderation in
driver stop routine. Also have msk_tick() reclaim transmitted Tx
buffers as safety belt. With this change there is no need to check
missing Tx completion interrupt in watchdog handler, so remove it.
full-duplex. Previously msk(4) used to allow flow-control on
1000baseT half-duplex media. Also GMAC pause is enabled if link
partner is capable of handling it.
While I'm here use IFM_OPTIONS instead of using IFM_GMASK to check
optional flags of link.
32 bit handles. The RIO (reduced interrupt operation) and fast posting
for the parallel SCSI cards were all 16 bit handles. Furthermore,
target mode parallel SCSI only can have 16 bit handles.
Use part of a supplied patch to switch over to using 32 bit handles.
Be a bit more conservative here and only do this for parallel SCSI
for the 12160 (Ultra3) cards. There were a lot of marginal Ultra2
cards, and, frankly, few are findable now for testing.
Fix the target handle routine to only do 16 bit handles for parallel
SCSI cards. This is okay because the upper sixteen bits of the new
32 bit handles is a sequence number to help protect against duplicate
completions. This would be very unlikely to happen with parallel
SCSI target mode, and wasn't present before, so we're no worse off
than we used to be.
While we're at it, finally split the async mailbox completion handlers
into FC and parallel SCSI functions. This makes it much cleaner and
easier to figure out what is or isn't a legal async mailbox completion
code for different card classes.
PR: kern/144250
Submitted partially by: Charles D
MFC after: 1 week
the issue. I still have no idea why TSO does not work on this
controller. davidch@ also confirmed there is no known TSO related
issues for this controller.
parsing code in TSO path as the controller requires VLAN hardware
tagging to make TSO work over VLANs.
While parsing the mbuf in TSO patch, always perform check for
writable mbuf as bce(4) have to reset IP length and IP checksum
field of IP header and make sure to ensure contiguous buffer before
accessing IP/TCP headers. While I'm here replace magic number 40 to
more readable sizeof(struct ip) + sizeof(struct tcphdr).
Reviewed by: davidch
TX/RX checksum handler to set/clear relavant assist bits which was
used to cause unexpected results.
With this change, bce(4) can be bridged with other interfaces that
lack TSO, VLAN checksum offloading.
Reviewed by: davidch
around. Management firmware(ASF/IPMI/UMP) requires the VLAN
hardware tag stripping so don't actually disable VLAN hardware tag
stripping. If VLAN hardware tag stripping was disabled, bce(4)
manually reconstruct VLAN frame by appending stripped VLAN tag.
Also remove unnecessary IFCAP_VLAN_MTU message.
Reviewed by: davidch
for controllers like 88E8053 which reports two MSI messages.
Because we don't get anything useful things with 2 MSI messages,
allocating 1 MSI message would be more sane approach.
While I'm here, enable MSI for dual-port controllers too. Because
status block is shared for dual-port controllers, I don't think
msk(4) will encounter problem for using MSI on dual-port
controllers.
The register offset is not valid on 88E8072 controller. Also don't
blindly increase max read request size to 4096, instead, use 2048
which seems to be more sane value and only change the value if the
hardware default size(512) was used on that register.
For PCIX controllers, use system defined constant rather than using
magic value.
While I'm here stop showing negotiated link width.
not require checksum LE configuration if checksum start and write
position is the same as before. So keep track last checksum start
and write position and insert new LE whenever the position is
changed. This reduces number of LEs used in TX path as well as
slightly enhance TX performance.
been around for a long time now (7.1-ish or even earlier); assume
they are present. These includes MSI, TSO, LRO, VLAN, INTR_FILTERS,
FIRMWARE, etc.
Also, eliminate some dead code and clean up in other places as part
of this quick once-over.
MFC after: 1 week
race as it could already have been tx'd and freed by that time. Place
the bpf tap just _before_ writing the gen bit.
This fixes a panic when running tcpdump on a cxgb interface.
- Add a separate palette data for 8-bit DAC mode when SC_PIXEL_MODE is set
and fill it up with default gray-scale palette data for text. Now we don't
have to set `hint.sc.0.vesa_mode' to get the default palette data.
- Add a new adapter flag, V_ADP_DAC8 to track whether the controller is
using 8-bit palette format and load correct palette when switching modes.
- Set 8-bit DAC mode only for non-VGA compatible graphics mode.
change and have isp_make_here scan the whole bus which will then scan all
luns.
I think xpt_rescan needs to be fixed, but that's a separable issue.
Suggested by: Alexander
not support TSO over VLAN if VLAN hardware tagging is disabled so
there is no need to check VLAN here.
While I'm here make sure to pullup IP/TCP headers in the first
buffer.
GEM_MIF_CONFIG_MDI0 cannot be trusted when the firmware has powered
down the chip so the internal transceiver has to be hardcoded. This
is also in line with the AppleGMACEthernet driver, which just doesn't
distinguish between internal/external transceiver and MDIO/MDI1
respectively in the first place. Tested by: Andreas Tobler
MFC after: 1 week
frame, make sure to update VLAN capabilities whenever jumbo frame
is configured.
While I'm here rearrange interface capabilities configuration. The
controller requires VLAN hardware tagging to make TSO work on VLANs
so explicitly check this requirement.
Tx DMA burst size 2048, I beleive PCIe maximum read request size
also should match to the value of Tx DMA burst size. With this
change I can get more than 800Mbps for TCP bulk transfers.
Previously I was not able to get more than 700Mbps. If I enable TSO
it now shows 927Mbps.
to make TSO work on VLAN. So if VLAN hardware tagging is disabled
explicitly clear TSO on VLAN. While I'm here remove duplicated
VLAN_CAPABILITIES call.
o uses v4 firmware instead of v3. A port will be committed to create
the bwn firmware module.
o supports B/G and LP(low power) PHYs.
o supports 32 / 64 bits DMA operations.
o tested on big / little endian machines so should work on all
architectures.
It'd not connected to the build until the firmware port is committed.
With FBS enabled, we have no idea what command caused timeout.
Implement same logic as in siis(4) - wait for other commands
complete or timeout and then give some more time.
- introduce drbr_needs_enqueue that returns whether the interface/br needs
an enqueue operation: returns true if altq is enabled or there are
already packets in the ring (as we need to maintain packet order)
- update all drbr consumers
- fix drbr_flush
- avoid using the driver queue (IFQ_DRV_*) in the altq case as the
multiqueue consumer does not provide enough protection, serialize altq
interaction with the main queue lock
- make drbr_dequeue_cond work with altq
Discussed with: kmacy, yongari, jfv
MFC after: 4 weeks
It is belived that that pass s not needed anymore.
Specifically it is not required now for the reasons that were given
in the removed comment.
Discussed with: jhb
MFC after: 4 weeks
Some current systems dynamically load SSDT(s) when _PDC/_OSC method
of Processor is evaluated. Other devices in ACPI namespace may access
objects defined in the dynamic SSDT. Drivers for such devices might
have to have a rather high priority, because of other dependencies.
Good example is acpi_ec driver for EC.
Thus we attach to Processors as early as possible to load the SSDTs
before any other drivers may try to evaluate control methods.
It also seems to be a natural order for a processor in a device
hierarchy.
On the other hand, some child devices on acpi cpu bus need to access
other system resources like PCI configuration space of chipset devices,
so they need to be probed and attached rather late.
For this reason we probe and attach the cpu bus at
SI_SUB_CONFIGURE:SI_ORDER_MIDDLE SYSINIT level.
In the future this could be done more elegantly via multipass.
Please note that acpi drivers that might access ACPI namespace from
device_identify will do that before _PDC/_OSC of Processors are evaluated.
Legacy cpu driver is not affected by this change.
PR: kern/142561 (in part)
Reviewed by: jhb
Silence from: acpi@
MFC after: 5 weeks
The softc obtained in device probe wouldn't be the same one used in
device attach. Drivers should not assume any values stored in softc
structure in probe routine will be available for its attach routine.
brightness, wired LAN power and bass gain), and update the description of
one previously unknown feature (display contrast). While here, expand on
a comment and remove two defines left over from an old version of the code.
Also update man page to document the above changes, and correct grammar.
PR: kern/127581
_PDC was deprecated in favor of _OSC long time ago, but it
seems that they still peacefully coexist and in some case
only _PDC is present.
Still _OSC provides a reacher interface and is capable to
report back its status.
If the status is non-zero, then report it, we may find
it useful to understand what firmware expects from OS.
Also clean up some comments that became less useful over time.
Reviewed by: njl, jhb, rpaulo
MFC after: 3 weeks
numbers and handle types in rational way. This will better protect from
(unwittingly) dealing with stale handles/commands.
Fix the watchdog timeout code to better protect itself from mistakes.
If we run an abort on a putatively timed out command, the command
may in fact get completed, so check to make sure the command we're
timing it out is still around. If the abort succeeds, btw, the command
should get returned via a different path.
TNT5004 IC. This involved a major rewrite of a number of things, as
this chip no longer supports the NAT7210 legacy mode but requires the
host to use the (more modern) FIFO mode.
In theory, this also ought to work on the older TNT4882C chip. I'll
probably add this as optional support (perhaps by a device.hints flag)
later on. By now, FIFO mode is *only* activates iff a TNT5004 chip
has been detected (where the old code didn't work at all), while
everything else is supposed to use the old code.
MFC after: 2 weeks
no effect. Make sure to clear error bits by writing 1. [1]
While I'm here use predefined value instead of hardcodig magic
vlaue.
Submitted by: msaitoh at NetBSD [1]
lagg and vlan the vlan attach/detach event is not being
handed down to em, this caused some init code not to run,
and thus VLANs did not work. Ultimately having the event
get propagated would be nice, but for now the solution is
to have HWFILTER off by default, when this is the case
VLANs will work, ifconfig can be used to turn it on and
then get HW tag filtering.
available today.
This card is a low power 802.11bgn that only does 11n rates up to MCS 7
(that's 65 Mbps in 20Mhz mode and 135 in 40Mhz mode).
802.11n is not yet supported, but will be in the future.
The driver still has a problem regarding to the setting of txpower on
the card, so don't expect good performance yet. After fixing this
problem, an MFC is possible.
Special thanks to iXsystems and S Smirnov <tonve at yandex.ru> for help
with the purchase of a netbook with this card.
Sponsored by: iXsystems, Inc.
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
format is higher than 6-bit instead of relying VGA compatibility flag.
This fixes palette problem of NVIDIA GeForce 6600. Reduce code differences
between palette load/save functions while we are here.
Tested by: danfe
Also, account for a quirk of AMD/ATI HPET which reports number of timers
instead of id of the last timer as manadated by the specification.
Currently this has no effect on functionality but in the future we may
make actual use of the HPET timers, not only of its timecounter.
MFC after: 2 weeks
igb now has a queue notion that has a single interrupt
with an RX/TX pair, this will reduce the total interrupts
seen on a system. Both em and igb have a new watchdog
method. igb has fixes from Pyun Yong-Hyeon that have
improved stability, thank you :)
I wish to MFC this for 7.3 asap, please test if able.
Limit early revisions from 6Gb/s to 3Gb/s by default, or they negotiate
only 1.5Gbps, when 3Gb/s devices connected.
Add dummy driver for PATA part of these controllers, preventing generic
driver attach them. It causes system freeze when SATA controller used after
PATA was touched.
the intention of having two ttys pointing to the same cfe console device was.
Also we were not initializing the output[] array passed in as input to
tty_makedev() so one name of the ttys was garbage.
Fix the code that calls cfe_write() to deal with the case where only a partial
buffer is written out.
cfe_cngetc() needs to return if there is no character available as input.
If we don't do this then the cfe_timeout() function will spin forever
because cfe_cngetc() will only ever return if there is valid input.
Approved by: imp (mentor)
frontend uses the same uPD7210 backend as the pcii ISA frontend, so
the backend has to cope with both situations.
Also, hide the first printf in pcii_probe (address mismatch) behind
bootverbose as the ISA bus parent tries to probe all configured ISA
devices against each driver, so a the console has been cluttered with
this message for a bunch of unrelated driver probes.
MFC after: 3 days
. Properly allocate all IO space resources. These cards scatter their
IO addresses over a range of 0x1600 bytes, and they require an
additional address for "special interrupt handling".
. Implement the "special interrupt handling" per the GPIB-PCIIA
Technical Reference Manual; this was apparently not declared for the
clone card this driver has been originally implemented for, but it
turned out to be needed for both, an original NI brand PCII/PCIIA
card as well as the Axiom AX5488 clone.
. Add some diagnostic messages for various resource allocation etc.
failures during probe.
. Add some comments about the structure of the IO address space that
is used by these cards.
MFC after: 1 day
implementation of heartbeat interval was 2 but there was typo which
caused the heartbeat is sent approximately every 5 seconds. This
caused unintended controller reset by firmware because firmware
thought OS was crashed.
Submitted by: Floris Bos < info <> je-eigen-domein dot nl >
Tested by: Andrzej Tobola < ato <> iem dot pw dot edu dot pl >
loopback.
- Change the meaning of "mix" OSS control. Now it controls loopback level,
according to comments in soundcard.h.
- Allow AD1981HD codecs to use playback mixer. Now driver should be able to
really use it.
- Fix bug in shared muters operation.
frames to be accepted while the driver is resetting the hardware.
This failure is generally observed when broadcast frames are received
during driver load and will generate "Unable to write CTX memory"
errors.
- Small changes to driver flags display.
This is not only a prudent thing to do, but also makes sure that probe
method is not confused by non-NULL 'private', if the previous attach
attempt fails for any reason.
PR: kern/142561
Tested by: Alex Goncharov <alex-goncharov@comcast.net>
MFC after: 4 days
chains. This part of code is to enhance performance so failing the
collapsing should not free TX frames. Otherwise bge(4) will
unnecessarily drop frames which in turn can freeze the network
connection.
Reported by: Igor Sysoev (is <> rambler-co dot ru)
Tested by: Igor Sysoev (is <> rambler-co dot ru)
copper and fiber interfaces over GMII so an explicit check is
necessary to know whether it was configured for fiber interface.
This change make BCM5715S work.
Tested by: olli
MFC after: 1 week
over GMII, make sure to enable GMII. With this change brgphy(4) is
used to handle the dual mode PHY. Since we still don't have a sane
way to pass PHY specific information to mii(4) layer special
handling is needed in brgphy(4) to determine which mode of PHY was
configured in parent interface.
This change make BCM5715S work.
Tested by: olli
Obtained from: OpenBSD
MFC after: 1 week
o Don't enable BGE_FLAG_BER_BUG on both 5722 and 5756, and based
on their PCI IDs rather than their chip IDs.
Reported by: several PC-BSD users via kmoore
Reviewed by: yongari, imp, jhb, davidch
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
from standard 3G wireless units by supplying a raw IP/IPv6 endpoint rather than
using PPP over serial. uhsoctl(1) is used to initiate and close the WAN
connection.
Obtained from: Fredrik Lindberg <fli@shapeshifter.se>
as different nearby ones, and was grabbed by MIXER_xxx() handler.
While there, replace '(cmd & MIXER_xxx(0)) == MIXER_xxx(0)' expressions
with more correct '(cmd & ~0xff) == MIXER_READ(0)'. Use of bit operations
to compare numeric fields doesn't looks sane.
MFC after: 1 month
now due to unidentified synchonization problem. For 7.1 soundcards 5.1
support handled correctly via software upmix done by sound(4).
Stereo stream is no more duplicated to all ports. If you loose sound, check
you are using right connectors. Front speakers connector is usually green,
center/LFE - orange, rear - black, side - gray.
Pertinant highlights from Myricom CHANGES file include:
- Make sure invalid external smbus activity cannot affect performance
- Fix to avoid a bug where the link could sometimes stay reported as
up on after unplugging the cable.
- For 8B NIC, make smbus connection passive at init to avoid
possible address conflicts
- Increase number of slices to 17 for multi-slice fw
- Fix a bug where packets dropped because of link_overflow could
be occasionally reported as bad_crc32
- Add selectable failover strategy for dual-port chip: symmetric or primary/backup
- On failover, send RARP broadcast to make the change immediately
known to the network
- Change endianess for PCI Device Serial Number
- For dual-port NICs, time to failover is now a few microsecs
instead of a few millisecs.
MFC after: 3 days
I/O port access is implemented on Itanium by reading and writing to a
special region in memory. To hide details and avoid misaligned memory
accesses, a process did I/O port reads and writes by making a MD system
call. There's one fatal problem with this approach: unprivileged access
was not being prevented. /dev/io serves that purpose on amd64/i386, so
employ it on ia64 as well. Use an ioctl for doing the actual I/O and
remove the sysarch(2) interface.
Backward compatibility is not being considered. The sysarch(2) approach
was added to support X11, but support for FreeBSD/ia64 was never fully
implemented in X11. Thus, nothing gets broken that didn't need more work
to begin with.
MFC after: 1 week
register, nVidia chipsets have different oppinion, requiring every interrupt
to be acknowledged there.
While there, add interrupt descriptions in multi-vector MSI mode.
Pass the channel argument as a real argument and not through
RXON. The RXON version seems to have problem with both the older
228.57.2.23 firmware and the latest 228.61.2.24 version resulting
in device initialization errors like:
wpa_supplicant[2928]: Failed to initiate AP scan.
kernel: firmware error log:
kernel: error type = "SYSASSERT" (0x00000005)
kernel: program counter = 0x0000147C
kernel: source line = 0x0000058B
kernel: error data = 0x0000058B00000000
kernel: branch link = 0x0000145A00001492
kernel: interrupt link = 0x000006DE00000000
kernel: time = 7310
...
kernel: iwn0: iwn_config: could not set TX power
kernel: iwn0: iwn_init_locked: could not configure device, error 35
By passing the current channel to hal->set_txpower() the firmware
error is fixed, at least for the 4965 chipset of my Thinkpad and
the ones tested by Bernhard.
Submitted by: Bernhard Schmidt <bschmidt@techwires.net>
Approved by: rpaulo
warning message and attach without setting the Ethernet address to a
random address. It is not believed that this code can actually be
executed, and if it does, we're better off printing an error message than
faking up an Ethernet address.
PR: kern/133239
Reviewed by: yongari (earlier version of patch)
Approved by: ed (mentor)
EEPROM on ST201 always returns 16bits data with little endian
format so conversion to host order is required.
This change fixes inversed ethernet address on sparc64.
command in the usb_msctest routines, as well as a general tidyup.
This now properly ejects the ZTE MF636, Option Gi0322 and Novatel MC950D
devices I have on my desk.
pci_delete_child() function called by the cardbus driver. The new function
uses resource_list_unreserve() to release the BARs decoded by the device
being removed.
Reviewed by: imp
Tested by: brooks
This should fix some Thinkpad specific problems such as
connecting to a headphone jack is not functional on X41.
Reviewed by: takawata
MFC after: 1 week
same ASIC ID of BCM5758 such that r198318 incorecctly enabled TSO
on BCM5754.BCM5754M controllers. BCM5754/BCM5754M needs a special
firmware to enable TSO and bge(4) does not support firmware based
TSO.
Reported by: ed
Tested by: ed
If the NAA is type 2, the Node WWN is the Port WWN with the 12 bits
of port (48..60) cleared. This iff a wwn fetched from NVRAM is zero.
MFC after: 1 week
Unfortunately there are two slight problems with that:
- Yacc and lex might generate code that generates warnings because of
this. Require yacc and lex to be rebuilt during bootstrap. I'm not
incrementing __FreeBSD_version here, because I assume someone else
will do this eventually.
- When running `make buildkernel', it uses share/mk from the source
treeo to build aicasm. Because aicasm also depends on lex, this would
break. Lower WARNS to 5 for now. We should just increment it to 6
again somewhere in the very far future.
stored in a BAR since the CIS BAR is mapped before the PCI bus driver
enumerates all the BARs. Without this change, the PCI bus driver would
attempt to initialize a BAR that was already allocated resulting in a panic.
handling for the PCIR_BIOS decoding enable bit from the cardbus driver.
The PCIR_BIOS BAR does include type bits like other BARs. Instead, it is
always a 32-bit non-prefetchable memory BAR where the low bit is used as a
flag to enable decoding.
Reviewed by: imp
This replaces d_mmap() with the d_mmap2() implementation and also
changes the type of offset to vm_ooffset_t.
Purge d_mmap2().
All driver modules will need to be rebuilt since D_VERSION is also
bumped.
Reviewed by: jhb@
MFC after: Not in this lifetime...
get required command protocol. But they have no idea about new commands,
such as DATA SET MANAGEMENT (TRIM). As soon as this info any way provided
by CAM, give controller specific instructions.
* new firmware
* untested support for 1000 and 6000 series
* bgscan support
* remove unnecessary RXON changes
* allow setting of country/regdomain by enforcing channel flags read
from the EEPROM
* suspend/resume fixes
* RF kill switch fixes
* LED adjustments
* several bus_dma*() related fixes
* addressed some LORs
* many other bug fixes
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Obtained from: Brandon Gooch <jamesbrandongooch at gmail dot com> (LED
related changes), Benjamin Kaduk <kaduk at mit dot edu>
(LOR fixes), OpenBSD
Fix some wrong usages.
Note: this does not affect generated binaries as this argument is not used.
PR: 137213
Submitted by: Eygene Ryabinkin (initial version)
MFC after: 1 month
blkif interface in Xen requires all I/O to be 512 byte aligned with each
segment bounded by a 4k page.
Note: This submission only documents the proper contraints for blkif I/O.
The alignment code in busdma does not yet handle alignment constraints
correctly in all cases.
* Correct a group of typos: for Core2 programmable events, check
user supplied umask values against the correct event descriptor
field.
Submitted by: Ryan Stone <rysto32 at gmail dot com>
Unlike TX interrupt, ST201 does not provide any mechanism to
suppress RX interrupts. ste(4) can generate more than 70k RX
interrupts under heavy RX traffics such that these excessive
interrupts make system useless to process other useful things.
Maybe this was the major reason why polling support code was
introduced to ste(4).
The STE_COUNTDOWN register provides a programmable counter that
will generate an interrupt upon its expiration. We program
STE_DMACTL register to use 3.2us clock rate to drive the counter
register. Whenever ste(4) serves RX interrupt, the driver rearm
the timer to expire after STE_IM_RX_TIMER_DEFAULT time and disables
further generation of RX interrupts. This trick seems to work well
and ste(4) generates less than 8k RX interrupts even under 64 bytes
UDP torture test. Combined with TX interrupts, the total number of
interrupts are less than 10k which looks reasonable on heavily
loaded controller.
The default RX interrupt moderation time is 150us. Users can change
the value at any time with dev.ste.%d.int_rx_mod sysctl node.
Setting it 0 effectively disables the RX interrupt moderation
feature. Now we have both TX/RX interrupt moderation code so remove
loop of interrupt handler which resulted in sub-optimal performance
as well as more register accesses.
This brings hwpmc(4) support for 2nd and 3rd generation XScale cores.
Right now it's enabled by default to make sure we test this a bit.
When the time comes it can be disabled by default.
Tested on Gateworks boards.
A man page is coming.
Obtained from: //depot/user/rpaulo/xscalepmc/...
transmitted frames. So request interrupt for every 16th frames. Due
to the limitation of hardware we can't suppress the interrupt as
driver should have to check TX status register. The TX status
register can store up to 31 TX status so driver can't send more
than 31 frames without reading TX status register.
With this change controller would not generate TX completion
interrupt for every frame, so reclaim transmitted frames in
ste_tick().
used to return success without respect to the result.
While I'm here use mii_mediachg() in ste_init_locked which allows
driver to use currently configured media. ste_ifmedia_upd() is
supposed to be called whenever user changes current media settings.
o Let RX filter handler program promiscuous/multicast filter as
well as broadcasting.
o Remove unnecessary register access.
o Simplify ioctl handler and have set_rxfilter to handle
IFF_PROMISC and IFF_ALLMULTI change instead of directly
programming the controller.
o Removed unnecessary error variable reinitialization in ioctl
handler.
o Add IFF_DRV_RUNNING check before programming multicast filter.
o Configure maximum allowed frame length before enabling MAC.
Datasheet didn't say the exact ordering of programming sequence
but it looks more natural to set maximum allowed frame length
first prior to enabling controller.
1ms. Since we switched to memory register mapping make sure to
flush PCI posted write by reading the register again.
While I'm here add additional delays in loop while driver waits the
completion of the reset.
If ste(4) encounter TX underrun or excessive collisions the TX MAC
of controller is stalled so driver should wake it up again. TX
underrun requires increasing TX threshold value to minimize
further TX underruns. Previously ste(4) used to reset controller
to recover from TX underrun, excessive collision and reclaiming
error. However datasheet says only TX underrun requires resetting
entire controller. So implement ste_restart_tx() that restarts TX
MAC and do not perform full reset except TX underrun case.
Now ste(4) uses CSR_READ_2 instead of CSR_READ_1 to read
STE_TX_STATUS register. This way ste(4) will also read frame id
value and we can write the same value back to STE_TX_FRAMEID
register instead of overwriting it to 0. The datasheet was wrong
in write back of STE_TX_STATUS so add some comments why we do so.
Also always invoke ste_txeoc() after ste_txeof() in ste_poll as
without reading TX status register can stall TX MAC.
is that the JBus to EBus bridges share the interrupt controller of a
sibling JBus to PCIe bridge (at least as far as the OFW device tree
is concerned, in reality they are part of the same chip) so we have to
probe and attach the latter first. That happens to be also the case
due to the fact that the JBus to PCIe bridges appear first in the OFW
device tree but it doesn't hurt to ensure the right order.
receiving incoming traffics, try harder to gracefully stop active
DMA cycles and then stop MACs. This is the way what datasheet
recommends and seems to work reliably. Resetting controller while
active DMAs are in progress is bad thing as we can't predict how
DMAs touche allocated TX/RX buffers. This change ensures controller
stop state before attempting to release allocated TX/RX buffers.
Also update MAC statistics which could have been updated during the
wait time of MAC stop.
While I'm here remove unnecessary controller resets in various
location. ste(4) no longer relies on hard controller reset to stop
controller and resetting controller also clears all configured
settings which makes it hard to implement WOL in near future.
Now resetting a controller is performed in ste_init_locked().
interrupt. If we want to use link state change interrupt ste(4)
should also implement auto-negotiation complete handler as well as
various PHY access handling. Now link state change is handled by
mii(4) polling so it will automatically update link state UP/DOWN
events which in turn make ste(4) usable with lagg(4).
r199559 added a private timer to drive watchdog and the timer also
used to drive MAC statistics update. Because the MAC statistics
update is called whenever statistics counter reaches near-full, it
drove watchdog timer too fast such that it caused false watchdog
timeouts under heavy TX traffic conditions.
Fix the regression by separating ste_stats_update() from driving
watchdog timer and introduce a new function ste_tick() that handles
periodic job such as driving watchdog, MAC statistics update and
link state check etc.
While I'm here clear armed watchdog timer in ste_stop().
link state and PHY related information.
Remove ste_link and ste_one_phy variable of softc as it's not used
anymore.
While I'm here add IFF_DRV_RUNNING check in ste_start_locked().
o Sorted includes and added missing header files.
o Added basic endianness support. In theory ste(4) should work on
any architectures.
o Remove the use of contigmalloc(9), contigfree(9) and vtophys(9).
o Added 8 byte alignment limitation of TX/RX descriptor.
o Added 1 byte alignment requirement for TX/RX buffers.
o ste(4) controllers does not support DAC. Limit DMA address space
to be within 32bit address.
o Added spare DMA map to gracefully recover from DMA map failure.
o Removed dead code for checking STE_RXSTAT_DMADONE bit. The bit
was already checked in each iteration of loop so it can't be true.
o Added second argument count to ste_rxeof(). It is used to limit
number of iterations done in RX handler. ATM polling is the only
consumer.
o Removed ste_rxeoc() which was added to address RX stuck issue
(cvs rev 1.66). Unlike TX descriptors, ST201 supports chaining
descriptors to form a ring for RX descriptors. If RX descriptor
chaining is not supported it's possible for controller to stop
receiving incoming frames once controller pass the end of RX
descriptor which in turn requires driver post new RX
descriptors to receive more frames. For TX descriptors which
does not support chaning, we exactly do manual chaining in
driver by concatenating new descriptors to the end of previous
TX chain.
Maybe the workaround was borrowed from other drivers that does
not support RX descriptor chaining, which is not valid for ST201
controllers. I still have no idea how this address RX stuck
issue and I can't reproduce the RX stuck issue on DFE-550TX
controller.
o Removed hw.ste_rxsyncs sysctl as the workaround was removed.
o TX/RX side bus_dmamap_load_mbuf_sg(9) support.
o Reimplemented optimized ste_encap().
o Simplified TX logic of ste_start_locked().
o Added comments for TFD/RFD requirements.
o Increased number of RX descriptors to 128 from 64. 128 gave much
better performance than 64 under high network loads.
the leading underscores since they are now implemented.
- Implement the tcpi_rto and tcpi_last_data_recv fields in the tcp_info
structure.
Reviewed by: rwatson
MFC after: 2 weeks
This device only appears on the ACPI bus, so isn't caught by the current
entry for it in the uart(4) ISA attachment.
PR: kern/140172
Reviewed by: jhb, marcel
Approved by: ed (mentor)
MFC after: 2 weeks
causes additional MSIs messages sent if several ports asked for attention
same time. Time window before clearing is not important, as these interrupts
are level triggered by interrupt source.
* Read the pci capability register to identify AGP 3 support
* Add missing smaller aperture sizes for AGP3 chips.
* Fix the aperture size calculation on AGP2 chips.
All sizes between 32M and 256M reported as 256M.
* Add \n to error string.
This all seems to get the CLE266 EPIA-M board agp working properly, now
back to work on drm.
MFC after: 2 weeks
Quite contrary to VT6130 datasheet which says it supports up to 8K
jumbo frame, VT6130 does not seem to send jumbo frame that is
larger than 4K in length. Trying to send a frame that is larger
than 4K cause TX MAC hang.
Even though it's possible to allow 4K jumbo frame for VT6130, I
think it's meaningless to allow 4K jumbo frame. I'm not sure VT6132
also has the same limitation but I guess it uses the same MAC of
VT6130.
controller will split the jumbo frame into multiple RX buffers.
However it seems the hardware always dma the frame to 8 bytes
boundary for the split frames. Only the first part of the fragment
can have 4 byte alignment and subsequent buffers should be 8 bytes
aligned. Change RX buffer the alignment requirement to 8 bytes from
4 bytes.
This tunable allows one to enable (1) or disable (0) gestures like tap
and tap-hold on Synaptics TouchPad when the Extended mode isn't enabled
(ie. "hw.psm.synaptics_support" not set).
By default, the value is -1 in order to keep the current behaviour of
not enabling/disabling gestures explicitly.
PR: kern/139272
Submitted by: David Horn <dhorn2000 AT gmail DOT com>
Reviewed by: David Horn <dhorn2000 AT gmail DOT com>
value is obtained by dividing it by 256, not by 2550; also,
one second is 10^9 nanoseconds, not 1800000000 nanoseconds.
- Due to rounding error, setting watchdog to a really small
timeout (<1 sec) was turning the watchdog off. It should
set the watchdog to a small timeout instead.
- Implemented error checking in ipmi_wd_event(), as required
by watchdog(9).
PR: kern/130512
Submitted by: Dmitrij Tejblum
- Additionally, check that the timeout value is within the
supported range, and if it's too large, act as required by
watchdog(9).
MFC after: 3 days
perform a function such as ejecting a 3G autoinstaller disk. The eventhandler
system properly tracks threads and is safe to unload, remove the
setting/clearing of a function pointer in the kernel by u3g(4) which included a
tsleep for safety.
controllers. TX/RX interrupt mitigation is controlled by
VGE_TXSUPPTHR and VGE_RXSUPPTHR register. These registers suppress
generation of interrupts until the programmed frames counter equals
to the registers. VT61xx also supports interrupt hold off timer
register. If this interrupt hold off timer is active all interrupts
would be disabled until the timer reaches to 0. The timer value is
reloaded whenever VGE_ISR register written. The timer resolution is
about 20us.
Previously vge(4) used single shot timer to reduce Tx completion
interrupts. This required VGE_CRS1 register access in Tx
start/completion handler to rearm new timeout value and it did not
show satisfactory result(more than 50k interrupts under load). Rx
interrupts was not moderated at all such that vge(4) used to
generate too many interrupts which in turn made polling(4) better
approach under high network load.
This change activates all interrupt moderation mechanism and
initial values were tuned to generate interrupt less than 8k per
second. That number of interrupts wouldn't add additional packet
latencies compared to polling(4). These interrupt parameters could
be changed with sysctl.
dev.vge.%d.int_holdoff
dev.vge.%d.rx_coal_pkt
dev.vge.%d.tx_coal_pkt
Interface has be brought down and up again before change take
effect.
With interrupt moderation there is no more need to loop in
interrupt handler. This loop always added one more register access.
While I'm here remove dead code which tried to implement subset of
interrupt moderation.
ethernet controller was recognized. VIA consistently calls
"Velocity" family for gigabit ethernet controllers. For fast
ethernet controllers they uses "Rhine" family(vr(4) controllers))
and vr(4) already shows "Rhine" in probe message.
tagged frames so add checksum offloading capabilities. Also add
missing VLAN hardware tagging control in ioctl handler and let
upper stack know current VLAN capabilities.
This is SMBus controller found in Intel Platform Controller Hub (PCH),
which is a general name that refers to Intel 5 Series chipsets and
3400 Series chipsets.
Submitted by: Dmitry S. Luhtionov <mitya@cabletv.dp.ua>
MFC after: 3 days
after ether_ifattach(), as ether_ifattach() initializes it with
ETHER_HDR_LEN.
While I'm here remove setting if_mtu, it's already handled in
ether_ifattach().
called and vge(4) used to drive auto-negotiation timer(mii_tick) in
vge_tick(). Therefore the mii_tick was not called for every hz such
that auto-negotiation complete was never handled in vge(4).
Use mii_pollstat to extract current negotiated speed/duplex instead
of mii_tick. The latter is valid only for auto-negotiation case.
While I'm here change the confusing function name vge_tick() to
vge_link_statchg().
is called in vge_init_lock(), vge(4) always used to reload EEPROM.
Also add more comment why vge(4) clears VGE_CHIPCFG0_PACPI bit.
While I'm here add missing new line in vge_reset().
controllers(VT613x), we assume the PHY address is 1.
Use the saved PHY address in MII register access routines and
remove accessing VGE_MIICFG register.
While I'm here save PCI express capability register which will be
used in near future.
record device specific bits. Remove vge_link and use vge_flags.
While here, move clearing link state before mii_mediachg() as
mii_mediachg() may affect link state.
if_alloc() of ifp. This fixes the panic reported in the PR, but
not the attach failure.
PR: kern/139079
Tested by: Steven Noonan <steven uplinklabs.net>
Reviewed by: thompsa
Approved by: ed (mentor)
MFC after: 2 weeks`
seems to work like a tag that indicates 'not list end' of queued
frames. Without having a VGE_TXDESC_Q bit indicates 'list end'. So
the last frame of multiple queued frames has no VGE_TXDESC_Q bit.
The hardware has peculiar behavior for VGE_TXDESC_Q bit handling.
If the VGE_TXDESC_Q bit of descriptor was set the controller would
fetch next descriptor. However if next descriptor's OWN bit was
cleared but VGE_TXDESC_Q was set, it could confuse controller.
Clearing VGE_TXDESC_Q bit for transmitted frames ensure correct
behavior.
o Separate TX/RX buffer DMA tag from TX/RX descriptor ring DMA tag.
o Separate RX buffer DMA tag from common buffer DMA tag. RX DMA
tag has different restriction compared to TX DMA tag.
o Add 40bit DMA address support.
o Adjust TX/RX descriptor ring alignment to 64 bytes from 256
bytes as documented in datasheet.
o Added check to ensure TX/RX ring reside within a 4GB boundary.
Since TX/RX ring shares the same high address register they
should have the same high address.
o TX/RX side bus_dmamap_load_mbuf_sg(9) support.
o Add lock assertion to vge_setmulti().
o Add RX spare DMA map to recover from DMA map load failure.
o Add optimized RX buffer handler, vge_discard_rxbuf which is
activated when vge(4) sees bad frames.
o Don't blindly update VGE_RXDESC_RESIDUECNT register. Datasheet
says the register should be updated only when number of
available RX descriptors are multiple of 4.
o Use __NO_STRICT_ALIGNMENT instead of defining VGE_FIXUP_RX which
is only set for i386 architecture. Previously vge(4) also
performed expensive copy operation to align IP header on amd64.
This change should give RX performance boost on amd64
architecture.
o Don't reinitialize controller if driver is already running. This
should reduce number of link state flipping.
o Since vge(4) drops a driver lock before passing received frame
to upper layer, make sure vge(4) is still running after
re-acquiring driver lock.
o Add second argument count to vge_rxeof(). The argument will
limit number of packets could be processed in RX handler.
o Rearrange vge_rxeof() not to allocate RX buffer if received
frame was bad packet.
o Removed if_printf that prints DMA map failure. This type of
message shouldn't be used in fast path of driver.
o Reduce number of allowed TX buffer fragments to 6 from 7. A TX
descriptor allows 7 fragments of a frame. However the CMZ field
of descriptor has just 3bits and the controller wants to see
fragment + 1 in the field. So if we have 7 fragments the field
value would be 0 which seems to cause unexpected results under
certain conditions. This change should fix occasional TX hang
observed on vge(4).
o Simplify vge_stat_locked() and add number of available TX
descriptor check.
o vge(4) controllers lack padding short frames. Make sure to fill
zero for the padded bytes. This closes unintended information
disclosure.
o Don't set VGE_TDCTL_JUMBO flag. Datasheet is not clear whether
this bit should be set by driver or write-back status bit after
transmission. At least vendor's driver does not set this bit so
remove it. Without this bit vge(4) still can send jumbo frames.
o Don't start driver when vge(4) know there are not enough RX
buffers.
o Remove volatile keyword in RX descriptor structure. This should
be handled by bus_dma(9).
o Collapse two 16bits member of TX/RX descriptor into single 32bits
member.
o Reduce number of RX descriptors to 252 from 256. The
VGE_RXDESCNUM is 16bits register but only lower 8bits are valid.
So the maximum number of RX descriptors would be 255. However
the number of should be multiple of 4 as controller wants to
update 4 RX descriptors at a time. This limits the maximum
number of RX descriptor to be 252.
Tested by: Dewayne Geraghty (dewayne.geraghty <> heuristicsystems dot com dot au)
Carey Jones (m.carey.jones <> gmail dot com)
Yoshiaki Kasahara (kasahara <> nc dor kyushu-u dot ac dotjp)
- These revisions no longer have cable detection capability.
- The UDMA support bit of register 0x4b has been dropped without an
replacement.
- According to Linux it's crucial for working ATAPI DMA support to
also set the reserved bit 1 of regsiter 0x53 with these revisions.
MFC after: 1 week
native, i.e. big-endian, format and convert as appropriate like we
also do with the multibyte fields of the other pages. This fixes
the output of acd_describe() to match reality on big-endian machines
without breaking it on little-endian ones. While at it, also convert
the remaining multibyte fields of the pages read although they are
currently unused for consistency and in order to prevent possible
similar bugs in the future.
MFC after: 1 week
was made in r199543 to remove MTX_RECURSE. These routines can be
called in device attach phase(e.g. mii_phy_probe()) so checking
assertion here is not right as caller does not hold a driver lock.
The rewrite of the interrupt handler includes:
o loop until all pending interrupts are handled. This closes a
race condition.
o count the number of interrupt sources we handled so that we can
properly return FILTER_HANDLED or FILTER_STRAY when we break out
of the loop.
o When matching the interrupt source to the devices that have that
source pending, check only from the set of devices we found to
have a pending interrupt.
PR: kern/140947
MFC after: 3 days
management over the data endpoint causes communication to die.
Take this one step further and model it on the existing NetBSD quirk and import
other device IDs from them.
Obtained from: NetBSD
are not allocated by the device driver. These resources should still appear
allocated from the system's perspective so that their assigned ranges are
not reused by other resource requests. The PCI bus driver has used a hack
to effect this for a while now where it uses rman_set_device() to assign
devices to the PCI bus when they are first encountered and later assigns
them to the actual device when a driver allocates a BAR. A few downsides of
this approach is that it results in somewhat confusing devinfo -r output as
well as not being very easily portable to other bus drivers.
This commit adds generic support for "reserved" resources to the resource
list API used by many bus drivers to manage the resources of child devices.
A resource may be reserved via resource_list_reserve(). This will allocate
the resource from the bus' parent without activating it.
resource_list_alloc() recognizes an attempt to allocate a reserved resource.
When this happens it activates the resource (if requested) and then returns
the reserved resource. Similarly, when a reserved resource is released via
resource_list_release(), it is deactivated (if it is active) and the
resource is then marked reserved again, but is left allocated from the
bus' parent. To completely remove a reserved resource, a bus driver may
use resource_list_unreserve(). A bus driver may use resource_list_busy()
to determine if a reserved resource is allocated by a child device or if
it can be unreserved.
The PCI bus driver has been changed to use this framework instead of
abusing rman_set_device() to keep track of reserved vs allocated resources.
Submitted by: imp (an older version many moons ago)
MFC after: 1 month
hw.bge.forced_collapse. hw.bge.forced_collapse affects all bge(4)
controllers on system which may not desirable behavior of the
sysctl node. Also allow the sysctl node could be modified at any
time.
Reviewed by: bde (initial version)
128 FIBs first and allocated more later if necessary. Remove now unused
definitions from the header file[1].
- Force sequential bus scanning. It seems parallel scanning is in fact
slower and causes more harm than good[1]. Adjust a comment to reflect that.
PR: kern/141269
Submitted by: Alexander Sack (asack at niksun dot com)[1]
Reviewed by: scottl
drivers. These add new hardware support, most importantly
the pch (i5 chipset) in the em driver. Also, both drivers
now have the simplified (and I hope improved) watchdog
code. The igb driver uses the new RX cleanup that I
first implemented in ixgbe.
em - version 6.9.24
igb - version 1.8.4
This adds new feature support for the 82599, a hardware
assist to LRO, doing this required a large revamp to the
RX cleanup code because the descriptor ring may not be
processed out of order, this necessitated the elimination
of global pointers.
Additionally, the RX routine now does not refresh mbufs
on every descriptor, rather it will do a range, and then
update the hardware pointer at that time. These are
performance oriented changes.
The TX side now has a cleaner simpler watchdog algorithm
as well, in TX cleanup a read of ticks is stored, that
can then be compared in local_timer to determine if
there is a hang.
Various other cleanups along the way, thanks to all who
have provided input and testing.
feature. These registers are reserved on controllers that have no
support for jumbo frame.
Only BCM5700 has mini ring so do not poke mini ring related
registers if controller is not BCM5700.
Reviewed by: marius
handler in brgphy(4) does not exist and brgphy(4) just resets the
PHY and returns EINVAL as it has no isolation handler. I also agree
on Marius's opinion that stop handler of every NIC driver seems to
be the wrong place for implementing PHY isolate/power down.
If we need PHY isolate/power down it should be implemented in
brgphy(4) and users should administratively down the PHY.
Reviewed by: marius
It makes MSI working there. Later (and cheaper) PCIe chips (3132/3531)
still randomly crashing system in few seconds of high MSI rates, generating
something inaporopriate, like NMI or "Fatal trap 30".
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
normal in case of media read error and some ATAPI cases, when transfer size
is unknown beforehand. PCI ATA BM specification tells that in case of such
underrun driver should just manually stop DMA engine. DMA engine should
same time guarantie that all bus mastering transfers completed at the moment
of driver reads interrupt flag asserted.
This change should fix interrupt storms and command timeouts in many cases.
PR: kern/103602, sparc64/121539, kern/133122, kern/139654
the loop down counter, as well as other things. This was brought to my
attention with a different fix, more for RELENG_7- this one covers the
multiple channel case.
PR: 140438
MFC after: 1 month
single outstanding DMA read operation. Most controllers targeted to
client with PCIe bus interface(e.g. BCM5761) may have this
limitation. All controllers for servers does not have this
limitation.
Collapsing mbuf chains to reduce number of memory reads before
transmitting was most effective way to workaround this. I got about
940Mbps from 850Mbps with mbuf collapsing on BCM5761. However it
takes a lot of CPU cycles to collapse mbuf chains so add tunable to
control the number of allowed TX buffers before collapsing. The
default value is 0 which effectively disables the forced collapsing.
For most cases 2 would yield best performance(about 930Mbps)
without much sacrificing CPU cycles.
Note the collapsing is only activated when the controller is on
PCIe bus and the frame does not need TSO operation. TSO does not
seem to suffer from the hardware limitation because the payload
size is much bigger than normal IP datagram.
Thanks to davidch@ who told me the limitation of client controllers
and actually gave possible workarounds to mitigate the limitation.
Reviewed by: davidch, marius
Ideally we should attempt attaching only to known supported devices.
But I am not sure that we have all supported PCI IDs already listed,
and I am too young to die, err, I don't want to take the heat from
causing a trouble to someone.
MFC after: 1 week
X-ToDo: drop the default case
ndis_scan() is called. However, ndis_scan() is invoked from softclock()
and cannot sleep. Move ndis_scan_results() to the ndis' driver's scan_end
hook instead.
Submitted by: Paul B Mahol onemda of gmail
MFC after: 1 week
The hardware is compliant with WDRT specification, so I originally
considered including generic WDRT watchdog support, but decided
against it, because I couldn't find anyone to the code for me.
WDRT seems to be not very popular.
Besides, generic WDRT porbably requires a slightly different driver
approach.
Reviewed by: des, gavin, rpaulo
MFC after: 3 weeks
baseline subtraction, and are very temperature sensitive, so would slowly
drift out of a calibrated state when under load. Escape this by taking
the last frame before we decide that the pad is idle as a finger-free
baseline.
Tested on: iBook G4
long as I remember, and completely superseded by better maintained umass(4).
It's main idea was to optionally avoid CAM dependency for such devices, but
with move ATA to CAM, it is not actual any more.
No objections: hselasky@, thompsa@, arch@
message has been printed is enough to get someones attention. Also remove the
line number for DPRINTF/DPRINTFN, it already prints the funtion name and a
unique message.
- fix a system deadlock on process exit when the sample buffer
is full (pmclog_loop blocked in fo_write) and pmcstat exit.
Reviewed by: jkoshy
MFC after: 3 weeks
bits on seems to confuse hardware TX engine.
- For 350 chips, set TX desc's buffer physical address before turning on the
TX desc valid bit.
Submitted by: Jeremy O'Brien obrien654j | gmail, sephe
Obtained from: DragonFly BSD
- Extend XPT-SIM transfer settings control API. Now it allows to report to
SATA SIM number of tags supported by each device, implement ATA mode and
SATA revision negotiation for both SATA and PATA SIMs.
- Make ahci(4) and siis(4) to use submitted maximum tag number, when
scheduling requests. It allows to support NCQ on devices with lower tags
count then controller supports.
- Make PMP driver to report attached devices connection speeds.
- Implement ATA mode negotiation between user settings, device and
controller capabilities.
Tx/Rx/Rx return ring such that large part of status block was not
used at all. All bge(4) controllers except BCM5700 AX/BX has a
feature to control the size of status block. So use minimum status
block size allowed in controller. This reduces number of DMAed
status block size to 32 bytes from 80 bytes.
seem to require a special firmware to use TSO. But the firmware is
not available to FreeBSD and Linux claims that the TSO performed by
the firmware is slower than hardware based TSO. Moreover the
firmware based TSO has one known bug which can't handle TSO if
ethernet header + IP/TCP header is greater than 80 bytes. The
workaround for the TSO bug exist but it seems it's too expensive
than not using TSO at all. Some hardwares also have the TSO bug so
limit the TSO to the controllers that are not affected TSO issues
(e.g. 5755 or higher).
While I'm here set VLAN tag bit to all descriptors that belengs to
a frame instead of the first descriptor of a frame. The datasheet
is not clear how to handle VLAN tag bit but it worked either way in
my testing. This makes it simplify TSO configuration a little bit.
Big thanks to davidch@ who sent me detailed TSO information.
Without this I was not able to implement it.
Tested by: current
have a DMA bug when buffer address crosses a multiple of the 4GB
boundary(e.g. 4GB, 8GB, 12GB etc). Limit DMA address to be within
4GB address for these controllers. The second DMA bug limits DMA
address to be within 40bit address space. This bug applies to
BCM5714 and BCM5715 and 5708(bce(4) controller). This is not
actually a MAC controller bug but an issue with the embedded PCIe
to PCI-X bridge in the device. So for BCM5714/BCM5715 controllers
also limit the DMA address to be within 40bit address space.
Special thanks to davidch@ who gave me detailed errata information.
I think this change will fix long standing bge(4) instability
issues on systems with more than 4GB memory.
Reviewed by: davidch
PCI flush to get correct status block update. Add an optimized
interrupt handler that is activated for MSI case. Actual interrupt
handling is done by taskqueue such that the handler does not
require driver lock for Rx path. The MSI capable bge(4) controllers
automatically disables further interrupt once it enters interrupt
state so we don't need PIO access to disable interrupt in interrupt
handler.
update and then clear status block. Previously it used to access
these index without synchronization which may cause problems when
bounce buffers are used. Also add missing bus_dmamap_sync(9) in
polling handler. Since we now update status block in driver, adjust
bus_dmamap_sync(9) for status block.
checking IFF_DRV_RUNNING and IFF_DRV_OACTIVE flags. Also if we
have less than 16 free send BDs set IFF_DRV_OACTIVE and try it
later. Previously bge(4) used to reserve 16 free send BDs after
loading dma maps but hardware just need one reserved send BD. If
prouder index has the same value of consumer index it means the Tx
queue is empty.
While I'm here check IFQ_DRV_IS_EMPTY first to save one lock
operation.
directly access them at fixed address. While I'm here don't touch
other bits of PCIe device control register except max payload size.
Reviewed by: marius
Binary divider value 10 specified in datasheet is not a hex 0x10.
UDMA2 should be 33/2 instead of 66/4, which is documented as reverved,
UDMA4 should be 66/2 instead of 66/4, which is definitely wrong.
controller also has support for IP/TCP checksum offloading for Rx
path. But I failed to find to way to enable Rx MAC to compute the
checksum of received frames.
both big-endian and little-endian format in descriptors for Rx path
but I couldn't find equivalent feature in Tx path. So just stick to
little-endian for now.
directly access them at fixed address. Frequently the register
offset could be changed if additional PCI capabilities are added to
controller.
One odd thing is ET_PCIR_L0S_L1_LATENCY register. I think it's PCIe
link capabilities register but the location of the register does
not match with PCIe capability pointer + offset. I'm not sure it's
shadow register of PCIe link capabilities register.
if_watchdog and if_timer.
- Fix some issues in detach for sn(4), ste(4), and ti(4). Primarily this
means calling ether_ifdetach() before anything else.
- Overhaul the locking to avoid recursion and add missing locking in a few
places.
- Don't schedule a task to call vge_start() from contexts that are safe to
call vge_start() directly. Just invoke the routine directly instead
(this is what all of the other NIC drivers I am familiar with do). Note
that vge(4) does not use an interrupt filter handler which is the primary
reason some other drivers use tasks.
- Add a new private timer to drive the watchdog timer instead of using
if_watchdog and if_timer.
- Fixup detach by calling ether_ifdetach() before stopping the interface.
just two different attachments (EISA and PCI) to a single driver.
- Add real locking. Previously these drivers only acquired their lock
in their interrupt handler or in the ioctl routine (but too broadly in
the latter). No locking was used for the stack calling down into the
driver via if_init() or if_start(), for device shutdown or detach. Also,
the interrupt handler held the driver lock while calling if_input(). All
this stuff should be fixed in the locking changes.
- Really fix these drivers to handle if_alloc(). The front-end attachments
were using if_initname() before the ifnet was allocated. Fix this by
moving some of the duplicated logic from each driver into pdq_ifattach().
While here, make pdq_ifattach() return an error so that the driver just
fails to attach if if_alloc() fails rather than panic'ing. Also, defer
freeing the ifnet until the driver has stopped using it during detach.
- Add a new private timer to drive the watchdog timer.
- Pass the softc pointer to the interrupt handlers instead of the device_t
so we can avoid the use of device_get_softc() and to better match what
other drivers do.
auto-negotiation. To make this simpler and easier to understand I have
split this out into two separate timers. One just manages the auto-neg
side of things and one is a transmit watchdog. Neither uses if_watchdog.
- Call ether_ifdetach() at the start of detach.
- Add a missing callout_drain() to detach.
- Hook into the stats timer and use that to drive the transmit watchdog
instead of using if_watchdog.
- Run the stats timer every second to match other drivers instead of every
other second.
- Remove dubious callout handling that stopped the timer only to start it
again while holding the driver lock without dropping it in between the
stop and the start.
reliable on some Marvell PHYs. If msk(4) know it still does not
have established link check whether msk(4) missed the link state
change by looking into polled link state.
Reported by: Mel Flynn < mel.flynn+fbsd.current <> mailing.thruhere dot net >,
Gleb Kurtsou <gleb.kurtsou <> gmail dot com >
Tested by: Gleb Kurtsou <gleb.kurtsou <> gmail dot com >
the transmit watchdog. These drivers already used a private timer when
compiled to use Netgraph. This change just makes them always use the
private timer. Note that these drivers do not compile and are disconnected
from the build due to TTY changes.
if_watchdog and if_timer. The driver already contained an optional stats
timer that individual attachments could use to provide a 'tick' event. The
stats timer only ran if the tick function pointer was non-NULL and the
attachment's tick routine had to call callout_reset(), etc. Now the driver
always schedules a stat timer and manages the callout_reset() internally.
This timer is used to drive the watchdog and will also call the attachment's
'tick' handler if one is provided.
Tested by: WATANABE Kazuhiro
and Marvell handled. Instead of trying to attach two different drivers to
single device, wrapping each call, make one of them (atajmicron, atamarvell)
attach do device solely, but create child device for AHCI driver,
passing it all required resources. It is quite easy, as none of
resources are shared, except IRQ.
As result, it:
- makes drivers operation more independent and straitforward,
- allows to use new ahci(4) driver with such devices, adding support for
new features, such as PMP and NCQ, same time keeping legacy PATA support,
- will allow to just drop old ataahci driver, when it's time come.
errors. So far 3 different classes are present (correctable,
uncorrectable and fatal) but more can be added easilly.
Obtained from: Sandvine Incorporated
Reviewed by: emase, gibbs
Sponsored by: Sandvine Incorporated
MFC: 2 weeks
These controllers provide combination of AHCI for SATA and legacy
PCI ATA for PATA. Use same solution as used for JMicron controllers.
Add IDs of Marvell 88SX6102, 88SX6111. 88SX6141 alike controllers
Right now syscons(4) uses a cons25-style terminal emulator. The
disadvantages of that are:
- Little compatibility with embedded devices with serial interfaces.
- Bad bandwidth efficiency, mainly because of the lack of scrolling
regions.
- A very hard transition path to support for modern character sets like
UTF-8.
Our terminal emulation library, libteken, has been supporting
xterm-style terminal emulation for months, so flip the switch and make
everyone use an xterm-style console driver.
I still have to enable this on i386. Right now pc98 and i386 share the
same /etc/ttys file. I'm not going to switch pc98, because it uses its
own Kanji-capable cons25 emulator.
IMPORTANT: What to do if things go wrong (i.e. graphical artifacts):
- Run the application inside script(1), try to reduce the problem and
send me the log file.
- In the mean time, you can run `vidcontrol -T cons25' and `export
TERM=cons25' so you can run applications the same way you did before.
You can also build your kernel with `options TEKEN_CONS25' to make all
virtual terminals use the cons25 emulator by default.
Discussed on: current@
page fault panic on initialization due to a large
number of bounce pages being allocated. This is due
to the dma tag requiring page alignment on mbuf mapping.
This was removed some time back from the ixgbe driver
and is not needed here either.
- Move tagged queueing control from ADA to ATA XPT. It allows to control
device command queue length correctly. First step to support < 32 tags.
- Limit queue for non-tagged devices by 2 slots for ahci(4) and siis(4).
- Implement quirk matching for ATA devices.
- Move xpt_schedule_dev_sendq() from header to source file.
- Move delayed queue shrinking to the more expected place - element freeing.
- Remove some SCSIsms in ATA.
xterm and cons25 have some incompatibilities when it comes to escape
sequences for special keys, such as F1 to F12, home, end, etc. Add a new
te_fkeystr() that can be used to override the strings.
scterm-sck won't do anything with this, but scterm-teken will use
teken_get_sequences() to obtain the proper sequence.
function that immediately reacquires the lock. Also removes recursive
locking.
- Use the statistics timer to drive the transmit watchdog instead of using
if_watchdog and if_timer.
Tested by: gavin
when they did their thing i.e. enabling SX mode
and then trying to load in. Since we are o32 this
is all un-needed. So I have re-structured the code
to work without doing this special set of code.
Packets now flow in and out.. however for some
reason dhcp/bootp response comes in and the kernel
does not proceed. Not sure if we have a UDP checksum error
or ?? The packets look all there by comparing wireshark
and the first 64 bytes of the TX and RX packets.
functions are selfcontained (ie. they touch only isa_dma.c static variables
and hardware) so a private lock is sufficient to prevent races. This changes
only i386/amd64 while there are also isa_dma functions for ia64/sparc64.
Sparc64 are ones empty stubs and ia64 ones are unused as ia64 does not
have isa (says marcel).
This patch removes explicit locking of Giant from a few drivers (there
are some that requires this but lack ones - this patch fixes this) and
also removes the need for implicit locking of Giant from attach routines
where it's provided by newbus.
Approved by: ed (mentor, implicit)
Reviewed by: jhb, attilio (glanced by)
Tested by: Giovanni Trematerra <giovanni.trematerra gmail com>
IA64 clue: marcel
during boot when ARC1200 is being used with certain motherboard models.
This commit brings the driver to the same state of vendor's 1.20.00.16
release. Many thanks to Areca for their continued support to FreeBSD.
Reported by: Jirka Mikulas <jiri mikulas com>
Submitted by: Erich Chen (Areca)
Obtained from: ftp://ftp.areca.com.tw/RaidCards/AP_Drivers/FreeBSD/DRIVER/SourceCode/arcmsr-freebsd-1.20.00.16-91010.zip
MFC after: 3 days
- fix issues regarding the mixer, where the interface number was not set in
time.
- fix wrong use of resolution parameter.
Submitted by: Hans Petter Selasky
Some EHCI chips from VIA / ATI seem to trigger interrupts before writing back
the qTD status, or miss signalling occasionally under heavy load. If the host
machine is too fast, we can miss transaction completion - when we scan the
active list the transaction still seems to be active. This generally exhibits
itself as a umass stall that never recovers.
We work around this behaviour by setting up this callback after any softintr
that completes with transactions still pending, giving us another chance to
check for completion after the writeback has taken place
Submitted by: Alexander Nedotsuko
MFC after: 3 days
Revision 1.158 says only lower ten bits of
BGE_RXLP_LOCSTAT_IFIN_DROPS register is valid. For BCM5761 case it
seems the controller maintains 16bits value for the register.
However 16bits are still too small to count all dropped packets
happened in a second. To get a correct counter we have to read the
register in bge_rxeof() which would be too expensive.
Pointed out by: bde
attach chips with generic Marvell (non-HighPoint) PCI identification.
These chips are also supported by ata(4). Some vendors, like Supermicro,
are using same chips without providing HPT RAID BIOS.
PR: kern/120842, kern/136750
MAC in bge_tick. Previously it used to show more number of input
errors. I noticed actual input errors were less than 8% even for
64 bytes UDP frames generated by netperf.
Since we always access BGE_RXLP_LOCSTAT_IFIN_DROPS register in
bge_tick, remove useless code protected by #ifdef notyet.
initializes it to ETHER_HDR_LEN so we have to override it after
calling ether_ifattch().
While I'm here remove setting if_mtu value, it's initialized in
ether_ifattach().
o acpi_hpet: auto-added 'wildcard' devices can be identified by
non-NULL handle attribute.
o acpi_ec: auto-add 'wildcard' devices can be identified by
unset (NULL) private attribute.
o acpi_cpu: use private instead of magic to store cpu id.
Reviewed by: jhb
Silence from: acpi@
MFC after: 2 weeks
X-MFC-Note: perhaps the ivar should stay for ABI stability
Introduce two spare dma maps for standard buffer and jumbo buffer
respectively. If loading a dma map failed reuse previously loaded
dma map. This should fix unloaded dma map is used in case of dma
map load failure. Also don't blindly unload dma map and defer
dma map sync and unloading operation until we know dma map for new
buffer is successfully loaded. This change saves unnecessary dma
load/unload operation. Previously bge(4) tried to reuse mbuf
with unloaded dma map which is really bad thing in bus_dma(9)
perspective.
While I'm here update if_iqdrops if we can't allocate Rx buffers.
standard buffer size. If controller is not capable of handling
jumbo frame, interface MTU couldn't be larger than standard MTU
which in turn the received should be fit in standard buffer. This
fixes bus_dmamap_sync call for jumbo ring is called even if
interface is configured to use standard MTU.
Also if total frame size could be fit into standard buffer don't
use jumbo buffers.
itself to an associated PCI device if it exists. It is little bit hackish
but it should fix build without frame buffer driver since r198964.
Fix some style(9) nits in vga_isa.c while we are here.
if_watchdog/if_timer to NULL/0 when initializing an ifnet. if_alloc()
sets those members to NULL/0 already.
(Missed this driver in the earlier commit.)
showing the message creates other side-effects. Remove the Rx
FIFO overrun message in interrupt handler. msk(4) should recover
from the FIFO overruns without any user intervention. Users can
still check the Rx FIFO overrun counter from MAC MIB statistics
maintained in driver(dev.msk.0.stats.rx.overflows).
for buffer allocation. If driver know we are out of Rx buffers let
controller stop. This should fix panic when interface is run even
if it had no configured Rx buffers.
and Rx DMA tag separately. Previously it used a common mbuf DMA tag
for both Tx and Rx path but Rx buffer(standard ring case) should
have a single DMA segment and maximum buffer size of the segment
should be less than or equal to MCLBYTES. This change also make it
possible to add TSO with minor changes.
bge_newbuf_std still has a bug for handling dma map load failure
under high network load. Just reusing mbuf is not enough as driver
already unloaded the dma map of the mbuf. Graceful recovery needs
more work.
Ideally we can just update dma address part of a Rx descriptor
because the controller never overwrite the Rx descriptor. This
requires some Rx initialization code changes and it would be done
later after fixing other incorrect bus_dma(9) usages.
- VBE 3.0 says palette format resets to 6-bit mode when video mode changes.
We simply set 8-bit mode when we switch modes if the adapter supports it.
- VBE 3.0 also says if the mode is not VGA compatible, we must use VBE
function to save/restore palette. Otherwise, VGA function may be used.
Thus, reinstate the save/load palette functions only for non-VGA compatible
modes regardless of its palette format.
- Let vesa(4) set VESA modes even if vga(4) claims to support it.
- Reset default palette if VESA pixel mode is set initially.
- Fix more style nits.
- Tear down the interrupt handler before killing the worker thread.
- Do geom withering as GEOM event to avoid acquiring the GEOM topology
lock under Giant.
PR: kern/104079
Reviewed by: joerg
Approved by: trasz (mentor)
- Rework timeout handling, to make it more graceful for devices sharing
controller port (with PMP). Wait for other commands completion/timeout
before initiating recovery.
- Handle timeouts and fatal errors with port hard-reset. The rest of
recovery will be done by XPT on receiving async event. More gracefull
per-device soft-reset recovery can be implemented later.
- Handle timeouts and fatal errors with port hard-reset. The rest of
recovery will be done by XPT on receiving async event. More gracefull
per-device soft-reset recovery can be implemented later.
- Add workaround for ATI SB600/SB700 PMP probe related bug, to speedup boot.
Most of the pieces came from Marius- correct settings for channels
and resource management. The one piece missing was that you cannot
for SBus cards replace 32 bit operations with A64 operations- not
supported.
Submitted by: marius
MFC after: 3 days
reacquiring driver lock in Rx handler. re(4) drops a driver lock
before passing received frame to upper stack and reacquire the
lock. During the time window ioctl calls could be executed and if
the ioctl was interface down request, driver will stop the
controller and free allocated mbufs. After that when driver comes
back to Rx handler again it does not know what was happend so it
could access free mbufs which in turn cause panic.
Reported by: Norbert Papke < npapk <> acm dot org >
Tested by: Norbert Papke < npapk <> acm dot org >
- Don't write actual length if the actual length pointer is NULL [2]
- correct Linux Compatibility error codes for short isochronous IN transfers
and make status field signed.
Submitted by: Leunam Elebek [1], Manuel Gebele [2]
do support 64bit addresses, the current SCRIPTS code supports only 32bit
addresses causing data corruption for buffer addresses >4GB. This problem
affects 64bit machines with more than 4GB RAM or amd64 with 4GB and
memory hole remapping.
Work-around this problem with a bus_dma tag that requests bounce-buffers
for addresses >4GB. This causes some overhead, but given the maximum SCSI
bus speed of 160MB/s compared, the effect should hardly be noticeable.
The problem was reported by Mike Watters (mike at mwatters net) who also
verified that this fix cures the problem.
Since this change is a NOOP on systems with less than 4GB RAM and fixes
data corruption (in RAM and on disk) on systems with more than 4GB, I hope
that this change is accepted for 8.0.
MFC after: 3 days (pending approval)
- Remove most of direct relations between ATA(4) peripherial and controller
levels. It makes logic more transparent and is a mandatory step to wrap
ATA(4) controller level into ATA-native CAM SIM.
- Tune AHCI and SATA2 SiI drivers memory allocation a bit to allow bigger
I/O transaction sizes without additional cost.
- Don't bother to assign vb until we know we have enough space
- Add variables for sx2, sy2, dx2, dy2 so that these aren't
calculated over and over, also reduce chance of errors.
- Use switch to assign color/format
MFC after: 3 days
- We don't need to check malloc return values with M_WAITOK
- remove variables that we don't really need
- cleanup the error paths by just calling drm_sg_cleanup()
- fix drm_sg_cleanup() to be safe to call at any time
MFC after: 2 weeks
obsoleted in 1996 by ATA-2, and crashes some modern hardware like some
revisions of the Serverworks K2 SATA controller. Even very ancient
hardware seems not to require it. In the unlikely event this causes
problems, the previous behavior can be re-enabled by defining
ATA_LEGACY_SUPPORT at the top of this file.
Reviewed by: Alexander Motin <mav@freebsd.org>
* iwnfw has now been split into individual modules so autoloading of
firmware module(s) does work again.
* Changes have been made to RUN -> AUTH transition, this should fix the
issue reported by Glen and others.
* Brandon reported issues in iwn_cmd() with large commands, those have
been fixed to.
* DEAUTH is now handled correctly.
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Have the early USB takeover enabled for i386 and amd64
by default.
This also avoids a panic on PowerPC where the resource
isn't released properly and we find a busy resource
when the USB host controller wants to allocate it...
function may not work properly if we don't. Turn off hardware cursor as
vesa_set_mode() does.
- Add VBE 3.0 specific fields in VESA mode structure and pack it. Note
the padding is 190 bytes although VBE 3.0 says 189 bytes. It must be wrong
because the size of structure becomes 255 bytes and the specification says
it must be 256 bytes in total. In fact, an example code in the spec. does
it right, though. While we are at it, fix some i386-isms.
- Remove state buffer size limitation. It is no longer necessary since
sys/compat/x86bios/x86bios.c r198251.
- Move int 0x10 vector test into vesa_bios_post() as we always do it anyway.
splitting in bce(4) instead of (ab)using ZERO_COPY_SOCKETS that was not
propagated into if_bce.c anyway. It is disabled by default.
Approved by: davidch
MFC after: 3 days
On error, freeze device queue, to allow periph driver to do proper recovery.
Freeze SIM queue only in some cases, when it is needed to protect SIM.
Implement better command timeout detection logic for non-queued commands.
This fixes false positives when command with short timeout waiting for the
long one. For example, when hald tastes CD during burning process.
Read and clear SERR register on interrupt.
instead of POSTREAD: the hardware do not touch this memory (CPU
updates it). It is already synchronized as PREWRITE after the
processing is done.
- Synchronize RX return ring memory in rx_eof. This is needed
as the deviced updates this memory when receives packets.
- Decouple the synchronization of BGE status block in the interrupt
service routine: perfrom PREREAD synchronization only all accesses
to this block are finished. This seems to be more natural.
Reviewed by: yongari, marius
MFC after: 2 weeks
has been yanked, this works around a cam recounting bug when
CAM_DEV_UNCONFIGURED is set late in the detach. In certain conditions the
reference to the XPT device would not be released which would cause the usb
explore thread to sleep forever on "simfree", preventing any new usb devices to
be found/ejected on the bus.
This is intended to be a quick workaround to the problem without touching CAM
so it can be merged to 8.0.
Suggested by: mav
MFC after: 3 days
by checking PCI config space when the NIC is not
transmitting. Previously, a h/w fault would not have been
detected if the NIC was down, or handling an RX only
workload.
the race where interrupt thread can complete the request for which
timeout has fired and while mpt_timeout has blocked on mpt_lock.
Do a best effort to keep 4.x ang Giant-locked configurartions
compiling still.
Reported by: ups
Reviewed by: scottl
- Do not map entire real mode memory (1MB). Instead, we map IVT/BDA and
ROM area separately. Most notably, ROM area is mapped as device memory
(uncacheable) as it should be. User memory is dynamically allocated and
free'ed with contigmalloc(9) and contigfree(9). Remove now redundant and
potentially dangerous x86bios_alloc.c. If this emulator ever grows to
support non-PC hardware, we may implement it with rman(9) later.
- Move all host-specific initializations from x86emu_util.c to x86bios.c and
remove now unnecessary x86emu_util.c. Currently, non-PC hardware is not
supported. We may use bus_space(9) later when the KPI is fixed.
- Replace all bzero() calls for emulated registers with more obviously named
x86bios_init_regs(). This function also initializes DS and SS properly.
- Add x86bios_get_intr(). This function checks if the interrupt vector is
available for the platform. It is not necessary for PC-compatible hardware
but it may be needed later. ;-)
- Do not try turning off monitor if DPMS does not support the state.
- Allocate stable memory for VESA OEM strings instead of just holding
pointers to them. They may or may not be accessible always. Fix a memory
leak of video mode table while I am here.
- Add (experimental) BIOS POST call for vesa(4). This function calls VGA
BIOS POST code from the current VGA option ROM. Some video controllers
cannot save and restore the state properly even if it is claimed to be
supported. Usually the symptom is blank display after resuming from suspend
state. If the video mode does not match the previous mode after restoring,
we try BIOS POST and force the known good initial state. Some magic was
taken from NetBSD (and it was taken from vbetool, I believe.)
- Add a loader tunable for vgapci(4) to give a hint to dpms(4) and vesa(4)
to identify who owns the VESA BIOS. This is very useful for multi-display
adapter setup. By default, the POST video controller is automatically
probed and the tunable "hw.pci.default_vgapci_unit" is set to corresponding
vgapci unit number. You may override it from loader but it is very unlikely
to be necessary. Unfortunately only AGP/PCI/PCI-E controllers can be
matched because ISA controller does not have necessary device IDs.
- Fix a long standing bug in state save/restore function. The state buffer
pointer should be ES:BX, not ES:DI according to VBE 3.0. If it ever worked,
that's because BX was always zero. :-)
- Clean up register initializations more clearer per VBE 3.0.
- Fix a lot of style issues with vesa(4).
was major changes to initialize RF chipset and set H/W registers and
removed a lot of magic numbers on code. Details are as follows:
- uses the endpoint 0x89 to get TX status information which used to
get TX complete or retry numbers or get a beacon interrupt. It's
only valuable for RTL8187B.
- removes urtw_write[8|16|32]_i functions that it's useless now.
- uses ic->ic_updateslot to set SLOT, SIFS, DIES, EIFS, CW_VAL
registers that doesn't set these whenever the channel is changed.
- code for initializing RF chipset for RTL8187B changed a lot that
there was many problems on TX transfers so it doesn't work properly
even if just for a ping/pong. Now it becomes more stable than
before that TX throughputs using netperf(1) were about 15 ~ 17Mbps/s
though sometimes it encounters packet losses.
- removes a lot of magic numbers that in the previous all of
representing RX and TX descriptors were consisted of magic numbers
and structures. It'd be more readable rather than before.
- calculates TX duration more accurately for urtw(4) devices.
- style(9)
that will need working on to fit from 6.x -> head. But first
I must get the base to compile (wanted to get as much in the tree
as I could before my flight to India).
all host controllers at the same time, we avoid problems where the BIOS will
actually write to the USB registers of all the USB host controllers every time
we handover one of them, and consequently reset the OS programmed values.
Submitted by: avg
Reviewed by: jhb
to the lock we hold, disable interrupts, and announce to the firmware
that we are shutting down. Especially do this before disabling blocks.
This makes some types of machines with asf enabled no longer hang upon
boot, when we start configuring the interface.
PR: i386/96382, kern/100410, kern/122252, kern/116328
Reported by: erwin
Hardware provided by: TDC A/S
Reviewed by: stas
Tested by: stas
Sun Type 6 USB keyboard support added in rev 1.46 conflicted with
some scan codes used in Japanese keyboards because the scan code
conversion routine was ambiguous for the overlapped codes.
PR: ports/134005
Submitted by: YAMASHIRO Jun
This is needed by the upcoming AR9285 support.
Information on the layout gathered from Linux ath9k.
Not yet connected to the build.
Tested by: Eugeny Dzhurinsky
BGE_PCI_PRODID_ASICREV register to store the chip identifier and its revision.
- Add new grouping macro for 7575+ chips (BGE_IS_5755_PLUS).
- Add IDs for Fujitsu-branded Broadcom adapters.
PR: kern/127587
Tested by: Thomas Quinot <thomas@quinot.org> (BCM7561 A0)
MFC after: 2 weeks
Obtained from: OpenBSD
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.
Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month
and progif is evil. It doesn't work reliably[1] and we should honor BIOS
configuration by the user.
- If the SATA controller is enbled but combined mode is disabled, mask off
the emulated IDE channel on the legacy IDE controller.
Pointed out by: mav[1]
interrupted and after re-run new files were not added to repo though
respective revisions were marked as merged. This commit presents latest
versions of these files.
interface is fairly simple WRT dealing with flow control, but
needed 2 new RX buffer functions with "get-char-from-buf" separated
from "advance-buf-pointer" so that the pointer could be advanced
only when ttydisc_rint() succeeded.
MFC after: 1 week
The EHCI HW can use the qtd_next field instead of qtd_altnext when a short
packet is received. This contradicts what is stated in the EHCI datasheet.
Also the total-bytes field in the status field of the following TD gets
corrupted upon reception of a short packet! We work this around in software by
not queueing more than one job/TD at a time of up to 16Kbytes! The bug has been
seen on multiple INTEL based EHCI chips. Other vendors have not been tested
yet.
- Applications using /dev/usb/X.Y.Z, where Z is non-zero are affected, but not
applications using LibUSB v0.1, v1.2 and v2.0.
- Mass Storage (umass) is affected.
Submitted by: Hans Petter Selasky
MFC after: 3 days
Also, the previous commit to sys/dev/if_ndis/if_ndis.c also included the
removal of a call to ndis_setstate_80211 that is no longer needed.
Submitted by: sam
MFC after: 3 days
sysctl lock. The 'video' lock now protects the 'bus' of video output
devices attached to a graphics adapter. It is used when iterating over
the list of outputs, etc. The 'video_output' lock is used to lock the
output-specific data similar to a driver lock for the individual video
outputs.
MFC after: 2 weeks
1) Restore the PCI Express control register after a watchdog
reset. This is required because the device will come out
of watchdog reset with the pectl reg at its default state,
and important BIOS configuration (like max payload size)
could be lost.
2) Call mxge_start_locked() for every tx queue before dropping
the lock in the watchdog handler. This is required, as
the queue's buf ring may have filled during the reset.
perform 802.11 operations directly on the ndis0 interface before the
first VAP (wlan0) had been created. This would lead to a NULL-pointer
dereference in the kernel.
Submitted by: Paul B. Mahol <onemda@gmail.com>
MFC after: 3 days
capability to mii(4). Even though AR8132 uses the same model/
revision number of F1 gigabit PHY, the PHY has no ability to
establish 1000baseT link. I have no idea why Atheros use the same
device/model id for this PHY.
With this change atphy(4) does not report 1000baseT media
capability and manual 1000baseT configuration is also disabled
which is more desirable behavior for 10/100Mbps PHY.
Unlike most other PHYs there is no easy way to know which media
type the PHY supports on Marvell PHYs. MIIF_HAVEFIBER flags is now
passed via bus-specific instance variable of a device. While I'm
here add 88E1112 specific work around to set SIGDET polarity low.
Many thanks "Eugene Perevyazko <john <> dnepro dot net>" who kindly
gave remote access to system with DGE-560SX.
offloading. Datasheet said nothing about the limitation of 82559ER
except WOL. Explicitly disable Rx checksum offloading for
controllers that is known to lack the capability.
PR: kern/138135
Tested by: Gooderum, Mark < mgooderum <> websense dot com >
- Add quirk for ATI SB600 and SB700 to free SMB controller
- Correct schedule sleep time to 10us on the VIA ehci controller
Reported by: Dorian B<FC>ttner, Andriy Gapon
Submitted by: Hans Petter Selasky
- clean up USB detach logic. There seems to be some problems detaching multiple
USB HUBs connected in series from the root.
- after this patch the rule is:
1) Always use device_detach() on the USB HUB first.
2) Never just device_delete_child() on the USB HUB, because that function
will traverse to all the device leaves and free them first, and then the USB
stack will free the devices twice which doesn't work very well.
- make sure the did DMA delay gets set after the timeout has elapsed to make
logic more clear. There is no functional difference.
Submitted by: Hans Petter Selasky
Right now if applications want to use the mouse on the command line,
they use sysmouse(4) and install a signal handler in the kernel to
deliver signals when mouse events arrive. This conflicts with my plan to
change to TERM=xterm, so implement proper VT200-style mouse input.
Because mouse input is now streamed through the TTY, it means you can
now SSH to another system on the console and use the mouse there as
well. The disadvantage of the VT200 mouse protocol, is that it doesn't
seem to generate events when moving the cursor. Only when pressing and
releasing mouse buttons.
There are different protocols as well, but this one seems to be most
commonly supported.
Reported by: Paul B. Mahol <onemda gmail com>
Tested with: vim(1)
It is quite inconvenient that if an application for xterm uses 256 color
mode, text suddenly starts to blink (because of ;5; in the middle).
We'd better just implement 256 color mode and add a conversion routine
from 256 to 8 color mode, which doesn't seem to be too bad in practice.
Remapping colors is done quite simple. If one of the channels is most
actively represented, primary colors are used. If two channels are most
actively represented, secondary colors are used. If all three channels
are equal (gray), it picks between black and white.
Reported by: Paul B. Mahol <onemda gmail com>
devices that we also support, just not by default (thus only LINT or
module builds by default).
While currently there is only "/dev/full" [2], we are planning to see more
in the future. We may decide to change the module/dependency logic in the
future should the list grow too long.
This is not part of linux.ko as also non-linux binaries like kFreeBSD
userland or ports can make use of this as well.
Suggested by: rwatson [1] (name)
Submitted by: ed [2]
Discussed with: markm, ed, rwatson, kib (weeks ago)
Reviewed by: rwatson, brueffer (prev. version)
PR: kern/68961
MFC after: 6 weeks
- Clear all registers before calling real mode interrupt handlers as we did
for dpms and vesa and re-enable the function as it should be fixed by this.
- Tidy up register access. For example, when we call INT 0x15, AH=0xc0,
we used to initialize AX=0xc000 to clear AL at the same time but it is
very confusing. We don't have to do this any more because we are explicitly
clearing all registers now.
- Check size of system configuration table although it is almost always 8.
This is to make sure we are not reading some random low physical memory.
Hopefully it is just zero in that case. :-)
- Fix some style nits and add more comments.
Submitted by: paradox (ddkprog yahoo com)[1]
memory to support them. Some adapters have expansible memory slots but
video mode table is static. In this case, unusable modes may be reported.
Submitted by: paradox (ddkprog yahoo com) (initial patch)
Also align setup descriptor on 32 bytes boundary. Tx buffer have no
alignment limitation so create dmamap without alignment
restriction[1]. Rx buffer still seems to require 4 bytes alignment
limitation but we can simply use MCLBYTES for size to map the
buffer instead of TULIP_DATA_PER_DESC as the buffer is allocated
with m_getcl(9).
de(4) supports up to TULIP_MAX_TXSEG segments for Tx buffers,
increase maximum dma segment size to TULIP_MAX_TXSEG * MCLBYTES.
While I'm here remove TULIP_DATA_PER_DESC as it is not used anymore.
This should fix de(4) breakage introduced after r176206.
Submitted by: jhb [1]
Reported by: WATANABE Kazuhiro < CQG00620 <> nifty dot ne dot jp >
Tested by: WATANABE Kazuhiro < CQG00620 <> nifty dot ne dot jp >,
Takahashi Yoshihiro < nyan <> jp dot freebsd dot org >
o introduce PCIE_REGMAX and use it instead of ad-hoc constant
o where 'reg' parameter/variable is not already unsigned, cast it to
unsigned before comparison with maximum value to cut off negative
values
o use PCI_SLOTMAX in several places where 31 or 32 were explicitly used
o drop redundant check of 'bytes' in i386 pciereg_cfgread() - valid
values are already checked in the subsequent switch
Reviewed by: jhb
MFC after: 1 week
save/clear/restore flags but emulated flags have no effect on the host.
I believe BIOS writers never meant to run their code in emulated
environment with interrupt enabled. :-)
- Use memcpy(3) instead of copying individual members. I believe struct
x86regs was intentionally copied from the first half of struct x86emu_regs
for this very purpose.
- Fix some style nits and consistencies.
Reviewed by: delphij, paradox (ddkprog yahoo com)
startup and genericize it so it can be reused to map other tables as well:
- Add a routine to walk a list of ACPI subtables such as those used in the
APIC and SRAT tables in the MI acpi(4) driver.
- Move the routines for mapping and unmapping an ACPI table as well as
mapping the RSDT or XSDT and searching for a table with a given signature
out into acpica_machdep.c for both amd64 and i386.
than references to objects. In that case, simply use the Package directly.
I think a recent change to ACPI-CA is causing the interpreter to
automatically expand these references.
Reported by: Olivier Smedts olivier gid0 org
MFC after: 3 days
decoding "took". Other OS's that I checked do not do this and it breaks
some amdpm(4) devices. Prior to 7.2 we did not honor the error returned
when this failed anyway, so this in effect restores previous behavior.
PR: kern/137668
Tested by: Aurelien Mere aurelien.mere amc-os.com
MFC after: 3 days
the work area was totally unsynchronized which means this driver only
had a chance of working on x86 when no bounce buffers were involved,
which isn't that likely given that support for 64-bit DMA is currently
broken throughout ata(4).
- Add necessary little-endian conversion of accesses to the work area,
making this driver work on big-endian hosts. While at it, use the
alignment-agnostic byte order encoders in order to be on the safe side.
- Clear the reserved member of the SG list entries in order to be on the
safe side. [1]
Submitted by: yongari [1]
Reviewed by: yongari
MFC after: 3 days
30-bit like the reset of the controllers supported by this driver.
Actually ALi M5451 can be setup up to generate 32-bit addresses by
setting the 31st bit via the accompanying ISA bridge, which allows
it to work in sparc64 machines whose IOMMU require at least 32-bit
DMA. Even though other architectures would also benefit from 32-bit
DMA, enabling this bit is limited to sparc64 as bus_dma(9) doesn't
generally guarantee that a low address of BUS_SPACE_MAXADDR_32BIT
results in a buffer in the 32-bit range.
- According to Tatsuo YOKOGAWA's ali(4), the the DMA transfer size of
ALi M5451 is fixed to 64k and in fact using the default size of 4k
- The 4DWAVE DX and NX require the recording buffer to be 8-byte
aligned so adjust the bus_dma_tag_create(9) accordingly.
- Unlike the rest of the controllers supported by this driver, the
ALi M5451 only has 32 hardware channels instead of 64 so limit the
loop in tr_intr() accordingly. [1]
Submitted by: yongari [1]
Reviewed by: yongari (superset of what is committed)
MFC after: 3 days
It seems Clang breaks when checking for SPCLKEY, which is now
0x80000000. Using an unsigned integer fixes this. This is also
consistent with other pieces of kbd/syscons code, because these also use
u_int.
Submitted by: rdivacky
- Mark the link as down, so if watchdog reset fails, link watching
failover software can notice it
- Don't send MXGEFW_CMD_ETHERNET_DOWN if the NIC has been reset, it is
not needed, and will fail on a freshly reset NIC.
- Ensure the transmit routines aren't attempting to PIO write to doorbells
while the NIC is being reset.
- Download the correct f/w, rather than using the EEPROM f/w after reset.
- Export a count of the number of watchdog resets via sysctl
- Zero all f/w stats at reset. This will lead to less confusing
diagnostic output when investigating NIC failures.
MFC after: 3 days
instead of SI_SUB_KLD. Note that we don't believe that there is any
consumers of x86bios that would be triggered in the early stage of boot,
so this is more or less just a safebelt.
Submitted by: swell.k at gmail.com
x86emu to this new module.
This changeset also brings a fix for bugs introduced with the initial
x86emu commit, which prevents the user from using some display mode or
cause instant reboots during mode switch.
Submitted by: paradox <ddkprog yahoo com>
Add a maximum response length for FCP RSPNS IUs.
Clarify some of the FC option words for setting parameters
and try and disable automatic PRLI when in target mode- this
should correct some cases of N-port topologies with 23XX cards
where we put out an illegal PRLI (in target mode only we're
not supposed to put out a PRLI).
Just take keyent_t to use an u_int to store the Unicode codepoints.
Unfortunately the keymap is now too big to be loaded using an ioctl
argument, so change the ioctl to pick a pointer.
This change breaks kbdcontrol ABI. It doesn't break X11, because X11
doesn't do anything with syscons keymaps. It just switches the device
out of K_XLATE.
Obtained from: //depot/user/ed/newcons/...
This code seems to do exactly the same as ttydisc_rint_simple() does
nowadays. Just remove it.
Obtained from: //depot/user/ed/newcons/sys/dev/syscons/syscons.c
- Implement MSI support (MSIX support was already there)
- Use a table to drive MSI/MSIX exceptions
- Pre-calculate the command address instead of wasting cycles doing the
calculation on every i/o.
number of MSIX interrupts that are needed, and don't strictly check for 4.
Enable enough interrupt mask bits so that the controller will generate
interrupts in PERFORMANT mode. This fixes the hang-on-boot issues that
people were seeing with newer controllers.
we at least don't panic.
We don't really support dual role mode (INITIATOR/TARGET) any more. We
should but it's broken and will take a fair amount of effort to fix
and correctly manage both initiator and target roles sharing the port
database. So, for now, disallow it.
For some vague reason, it may be possible that scp->cursor_pos exceeds
scp->ysize * scp->xsize. This means that teken_set_cursor() may get
called with an invalid position. Just ignore the old cursor position in
this case.
Reported by: Paul B. Mahol <onemda gmail com>
MFC after: 1 month
- Improve newer AMD processor support (Family 0Fh Revision F and later).
- Adjust offset if DiodeOffet is set and valid. Note it is experimental
but it seems to give us more realistic temperatures. Newer Linux driver
blindly adds 21C for Family 0Fh desktop processors, however.
- Always populate dev.cpu and dev.amdtemp sysctl trees regardless of probe
order for consistency. Previously, dev.cpu.N.temperature was not populated
if amdtemp was loaded later than ACPI CPU driver and temperatures were not
accessible from dev.amdtemp.N.sensor0 tree for Family 10h/11h processors.
- Read the CPUID from PCI register instead of CPUID instruction to prevent
possible revision mismatches on multi-socket system.
- Change macros and variables to make them closer to AMD documents.
- Fix style(9) nits and improve comments.
Different sub-kinds of PCI buses may have different rules and
thus it is up for the bus backends to do proper input checks.
For example, PCIe allows configuration register numbers < 0x1000,
while for PCI proper the limit is 0x100.
And, in fact, the buses already do the checks.
Reviewed by: jhb
MFC after: 1 week
X-ToDo: add check for negative value to bus backends
X-ToDo: use named constant for maximum PCIe register
"set vesa mode" and higher 16bits of the flag would be the desired mode.
One can now set, for instance, hint.sc.0.flags=0x01680180, which means
that the system should set VESA mode 0x168 upon boot.
Submitted by: paradox <ddkprog yahoo com>, swell k at gmail.com with
some minor changes.
| grep <modname>' can be used instead.
Put a message behind bootverbose as
ichwd0: <Intel ICH6M watchdog timer> on isa0
ichwd0: Intel ICH6M watchdog timer (ICH6 or equivalent)
does not make a lot of sense.
MFC after: 1 week
where we figure out the hostname length under the lock, malloc the buffer
with the lock dropped, then recheck the length under the lock and loop again
if the buffer is now too small.
Tested by: Norbert Koch nkoch demig de
MFC after: 3 days
- Add vesa kernel options for amd64.
- Connect libvgl library and splash kernel modules to amd64 build.
- Connect manual page dpms(4) to amd64 build.
- Remove old vesa/dpms files.
Submitted by: paradox <ddkprog yahoo com> [1], swell k at gmail.com
(with some minor tweaks)
them from the old place. This commit necessary so that the tree would not
enter a broken state.
sys/i386/isa/vesa.c -> dev/fb/vesa.c
sys/i386/include/pc/vesa.h -> dev/fb/vesa.h
sys/i386/isa/dpms.c -> dev/dpms/dpms.c
"COMMAND 0x........ TIMEOUT AFTER .. SECONDS" messages. Any commands
that get truly stuck will still trigger the warning and the hardware
health check, just a little bit later.
# My reading of the docs suggests this can only happen on 10Base5 and
# 10Base2 setups (and maybe only the former), which I can't test
# adequately since I have nothing but 10BaseT, etc here.
requirements. It is busdma task, to manage proper alignment by loading
data to bounce buffers.
PR: kern/127316
Reviewed by: current@
Tested by: Ryan Rogers
Now that pty(4) is a loadable kernel module, I'd better move /dev/ptmx
in there as well. This means that pty(4) now provides almost all
pseudo-terminal compatibility code. This means it's very easy to test
whether applications use the proper library interfaces when allocating
pseudo-terminals (namely posix_openpt and openpty).
sure when this became necessary and might be caused by some missing
code to do auto-configuration of DWDS usage
Noticed by: Felix Feng <unixwind@gmail.com>
Right now libteken processes TF_REVERSE internally and returns the
toggled colors to the console driver. This isn't entirely correct. This
means that the bold flag is always processed by the foreground color,
while reversing should be done after the foreground color has been set
to a brighter version by the bold flag.
This is no problem with the syscons driver, because with VGA it only
supports 16 foreground and 8 background colors. My WIP console driver
reconfigures the graphics hardware to disable the blink functionality
and uses 16 foreground and 16 background colors. This means that this
driver will handle the TF_REVERSE flag a little different from what
syscons does right now.
I initially committed libteken to sys/dev/syscons/teken, but now that
I'm working on a console driver myself, I noticed this was not a good
decision. Move it to sys/teken to make it easier for other drivers to
use a terminal emulator.
Also list teken.c in sys/conf/files, instead of listing it in all the
files.arch files separately.
out of the original commit of i7 support. These are all the counters
on pages A-32 and A-33 of the _Intel(R) 64 and IA32 Architectures
Software Developer's Manual Vol 3B_, June 2009. Almost all
of these counters relate to operations on the L2 cache.
Reviewed by: jkoshy
MFC after: 1 month
alignment requirement could be multiple of 4 bytes but I think
using descriptor size would make intention clearer.
Previously the size of rx descriptor was not power of 2 so it
caused panic in bus_dmamem_alloc(9).
Reported by: Jeff Blank (jb000003 <> mr-happy dot com)
MFC after: 3 days
the previous ap is no longer in range) the device will deliver bmiss
interrupts and trigger the state machine. Also arrange to sync the
beacon timers on the next received beacon frame so that when we don't
roam we re-synchronize with the ap.
Tested by: trasz
MFC after: 1 week
turn ends our usb process. This means the proc pointer becomes invalid and will
panic if a new kthread is added. Count the number of threads and clear the proc
pointer on the last one.
Suggested by: julian
MFC after: 3 days
per platform requirements.
Notes:
- Only used by mge(4) at the moment.
- This is very simplified approach and should be replaced by some long-term
solution for managing the board/platform configuration (among others the
MAC-PHY binding info).
Submitted by: Michal Hajduk
Obtained from: Semihalf
BIOS-enumerated devices:
- Assume a device is a match if the memory and I/O ports match even if the
IRQ or DRQ is wrong or missing. Some BIOSes don't include an IRQ for
the atrtc device for example.
- Add a hack to better match floppy controller devices. Many BIOSes do not
include the starting port of the floppy controller listed in the hints
(0x3f0) in the resources for the device. So far, however, all the BIOS
variations encountered do include the 'port + 2' resource (0x3f2), so
adjust the matching for "fdc" devices to look for 'port + 2'.
Reviewed by: imp
MFC after: 3 days
and remove from its dependency on LRO, my tests have shown
that its always beneficial, even when doing bridging.
Second, fix up a few problems in the statistics code, the
adapter dependencies had gotten lost so some code that should
only run on 82599 was always running, this resulted in bogus
flow control numbers on 82598.
- Use CONSOLE_DRIVER() instead of the deprecated CONS_DRIVER() declaration.
- This means we cannot use cn_checkc anymore, which is supposed to do
the same as cn_getc nowadays. Remove the cn_getc implementation (that
was never being called) and rename cn_checkc to cn_getc.
- Don't run-time patch cn_putc, but add the logic to xc_cnputc().
This means I could do some cleanups to our console code...
Tested by: nobody on hackers@
being polled.
- Remove the need for Giant from the USB HUB driver.
- Leave device unconfigured instead of disabling the USB port
when Huawei Autoinstall disk detection triggers. This should
fix problems that the Huawei device is not detected after
Autoinstall eject is issued.
- Reported by: Nikolay Antsiferov
- Fix memory use after free race for USB character devices.
- Reported by: Lucius Windschuh
- Factor out the enumeration lock into three functions to make the
coming newbus lock conversion more easy.
- usbd_enum_lock
- usbd_enum_unlock
- usbd_enum_is_locked
Submitted by: hps
enable the ones we want. This has been changed to better
match the ADMtek's reference design to avoid setting the
power-down configuration line of the PHY at the same time
it is reset.
Submitted by: John Hood via hps
direction even if the actual device is opened for read and
write. Fix fflags check so that the UFM and URIO drivers work.
Reported by: Krassimir Slavchev
Submitted by: hps
keys are pressed.
- Reported by: Various people
- add sysctl to disable keyboard led control request
- Reported by: Yoshihiro Ota
- Save system CPU usage: Patch to stop keyboard timer when no
keys are pressed.
Submitted by: hps
MFC after: 3 days
Unfortunately, the wrappers that are present in pts(4) don't have the
mechanics to allow pty(4) to be unloaded safely, so I'm forcing this kld
to return EBUSY. This also means we have to enable some extra code in
pts(4) unconditionally.
Proposed by: rwatson
I noticed several drivers in our tree don't actually care about parity
and framing, such as pts(4), snp(4) (and my partially finished console
driver). Instead of duplicating a lot of code, I think we'd better add a
utility function for those drivers to quickly process a buffer of input.
Also change pts(4) and snp(4) to use this function.
It is necessary to make sure cpi->transport is set for xpt_scan_bus() to
work properly.
Submitted by: Bernhard Schmidt (scb+freebsd-current <at> techwires
<dot> net)
Reviewed by: scottl
Approved by: re (kib)
Without this changeset there will be no way to prevent these NICs from
sending ARP, which is harmful in server farms that is configured as
"Direct Server Return" behind a load balancer.
A better fix would remove the whole hack completely but it would be
later than 8.0-RELEASE.
Reviewed by: jfv, yongari
Approved by: re (kib)
- usb_pc_cpu_invalidate() is called between [consecutive] reads from a device,
so a sequence of BUS_DMASYNC_POSTREAD and _PREREAD should be used. Note we
cannot use or'ed shorthand ( _POSTREAD | _PREREAD) for BUS_DMASYNC flags, as
the low level bus dma sync operation is implementation dependent and we
cannot assume the required order of operations to be guaranteed.
- usb_pc_cpu_flush() is called before writing to a device, so
BUS_DMASYNC_PREWRITE should be used.
Submitted by: Grzegorz Bernacki
Reviewed by: HPS, arm@, usb@ ML
Tested by: HPS, Mike Tancsa
Approved by: re (kib)
Obtained from: Semihalf
loop iteration as it can be updated by the card while we
process the RX ring forcing us to process RX descriptors
for which DMA synchronisation operation has not been
performed. This fixes the bug when bge(4) drops packets
under high load.
Discussed with: yongari, marius
Approved by: re (kib)
MFC after: 1 week
value instead of blindly resetting it to 0. However, it seems page
select bits of some 88E1116 PHY is initialized to invalid one such
that restoring page select bits after programming broke MII
register access. The correct solution would be reset page select
bits to 0 in PHY attach stage but it would require more testing.
Since we're in BETA stage such a change would be dangerous so just
back it out.
This change should fix nfe(4) breakage on NVIDIA MCP55.
Reported by: Ryan Rogers < webmaster <> doghouserepair dot com >
Sam Fourman Jr. < sfourman <> gmail dot com >
Tested by: Ryan Rogers < webmaster <> doghouserepair dot com >
Sam Fourman Jr. < sfourman <> gmail dot com >
Approved by: re (kib)
cosmetic change to reduce cruft in the proc table.
Also change the idle wait message to `-` like how taskqueues are.
Reviewed by: julian
Approved by: re (kib)
- Provide lapic_disable_pmc(), lapic_enable_pmc(), and lapic_reenable_pmc()
routines in the local APIC code that the hwpmc(4) driver can use to
manage the local APIC PMC interrupt vector.
- Do not enable the local APIC PMC interrupt vector by default when
HWPMC_HOOKS is enabled. Instead, the hwpmc(4) driver explicitly
enables the interrupt when it is succesfully initialized and disables
the interrupt when it is unloaded. This avoids enabling the interrupt
on unsupported CPUs which may result in spurious NMIs.
Reported by: rnoland
Reviewed by: jkoshy
Approved by: re (kib)
MFC after: 2 weeks
controllers. Controller, array, and drive status can be checked, basic
attributes can be changed, and arrays and spares can be created and deleted.
Controller firmware can also be flashed.
This does not replace MegaCLI, found in ports, as that is officially sanctioned
and supported by LSI and includes vastly more functionality. However, mfiutil
is open source and guaranteed to provide basic functionality, which can be
especially useful if you have a problem and can't get MegaCLI to work.
Approved by: re
Obtained from: Yahoo! Inc.
all pertinent statatistics for the subsystem. These structures are
sometimes "borrowed" by kernel modules that require a place to store
statistics for similar events.
Add KPI accessor functions for statistics structures referenced by kernel
modules so that they no longer encode certain specifics of how the data
structures are named and stored. This change is intended to make it
easier to move to per-CPU network stats following 8.0-RELEASE.
The following modules are affected by this change:
if_bridge
if_cxgb
if_gif
ip_mroute
ipdivert
pf
In practice, most of these statistics consumers should, in fact, maintain
their own statistics data structures rather than borrowing structures
from the base network stack. However, that change is too agressive for
this point in the release cycle.
Reviewed by: bz
Approved by: re (kib)
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
vnet.h, we now use jails (rather than vimages) as the abstraction
for virtualization management, and what remained was specific to
virtual network stacks. Minor cleanups are done in the process,
and comments updated to reflect these changes.
Reviewed by: bz
Approved by: re (vimage blanket)
firmware loading bugs.
Target mode support has received some serious attention to make it
more usable and stable.
Some backward compatible additions to CAM have been made that make
target mode async events easier to deal with have also been put
into place.
Further refinement and better support for NP-IV (N-port Virtualization)
is now in place.
Code for release prior to RELENG_7 has been stripped away for code clarity.
Sponsored by: Copan Systems
Reviewed by: scottl, ken, jung-uk kim
Approved by: re
USB core:
- add support for defragging of written device data.
- improve handling of alternate settings in device side mode.
- correct return value from usbd_get_no_alts() function.
- reported by: HPS
- P4 ID: 166156, 166168
- report USB device release information to devd and pnpinfo.
- reported by: MIHIRA Sanpei Yoshiro
- P4 ID: 166221
Submitted by: hps
Approved by: re
See PR description for more info. Patch is
implemented differently than suggested, but
having the same result.
PR: usb/137188
Submitted by: hps
Approved by: re
- add support for defragging of written device data.
- improve handling of alternate settings in device side mode.
- correct return value from usbd_get_no_alts() function.
- reported by: HPS
- P4 ID: 166156, 166168
- report USB device release information to devd and pnpinfo.
- reported by: MIHIRA Sanpei Yoshiro
- P4 ID: 166221
Submitted by: hps
Approved by: re
- Add minimum polling support to drive UMASS
and UKBD in case of panic.
- Add extra check to ukbd probe to fix problem about
mouse devices attaching like keyboards.
- P4 ID: 166148
Submitted by: hps
Approved by: re
- add support for setting the UMS polling rate through -F option
passed to moused.
- requested by Alexander Best
- P4 ID: 166075
PR: usb/125264
Submitted by: hps
Approved by: re
requesting IDENTIFY from slave device first. This order is important
for proper cable type detection by master device.
PR: kern/136438
Approved by: re (kib)
- When a vlan event occurs a check was not made that
the event was actually for the interface, thus resulting
in a panic. All three drivers have this vulnerability. Add
a check for this condition.
- Secondly, there was a duplicate buf_ring free in the em
driver resulting in a panic on unload. Remove.
Approved by: re
part that is made up of 8K banks rather than 4K, if these
systems are using bank 1 then the last change in this code
breaks the bank read, resulting in an invalid checksum of
the eeprom during driver load. This change fixes this.
Approved by: re
if input-device is unavailable. The Xserve G5 defaults to using
screen/keyboard for output-device/input-device even if these are not
installed, and then falls back to serial ports at boot time.
Reviewed by: marcel
Hardware from: grehan
Approved by: re (kib)
loader, because it uses a reserved suffix (_type). Fix
this by removing the "_" and renaming the tunable to
hw.mxge.rss_hashtype. The old (rss_hash_type) tunable is
still fetched, in case people load the driver via scripts.
When both are present in the kernel environment,
the new value (hw.mxge.rss_hashtype) overrides the old
value.
Approved by: re (kib)
actually specify valid bases that should be treated just as normal.
The PCI specifications have no indication that 0 would be a magic value
indicating a disabled BAR as commonly used on at least amd64 and i386
but not sparc64. It's unclear what to do in pci_delete_resource()
instead of writing 0 to a BAR though as there's no (other) way do
disable individual BARs so its decoding is left enabled in case of
__PCI_BAR_ZERO_VALID for now.
Approved by: re (kib), jhb
MFC after: 1 week
Driver supports Serial ATA and ATAPI devices, Port Multipliers
(including FIS-based switching), hardware command queues (31 command
per port) and Native Command Queuing. This is probably the second on
popularity, after AHCI, type of SATA2 controllers, that benefits from
using CAM, because of hardware command queuing support.
Approved by: re (kib)
nagged again via PR. Thank Paul for his persistence and contributions.
PR: 136895
Submitted by: Paul B. Mahol <onemda@gmail.com>
Reviewed by: sam (timeout, 10 days), weongyo (timeout, 10 days), me
Approved by: re (Kostik Belousov <kostikbel@gmail.com>)
(DPCPU), as suggested by Peter Wemm, and implement a new per-virtual
network stack memory allocator. Modify vnet to use the allocator
instead of monolithic global container structures (vinet, ...). This
change solves many binary compatibility problems associated with
VIMAGE, and restores ELF symbols for virtualized global variables.
Each virtualized global variable exists as a "reference copy", and also
once per virtual network stack. Virtualized global variables are
tagged at compile-time, placing the in a special linker set, which is
loaded into a contiguous region of kernel memory. Virtualized global
variables in the base kernel are linked as normal, but those in modules
are copied and relocated to a reserved portion of the kernel's vnet
region with the help of a the kernel linker.
Virtualized global variables exist in per-vnet memory set up when the
network stack instance is created, and are initialized statically from
the reference copy. Run-time access occurs via an accessor macro, which
converts from the current vnet and requested symbol to a per-vnet
address. When "options VIMAGE" is not compiled into the kernel, normal
global ELF symbols will be used instead and indirection is avoided.
This change restores static initialization for network stack global
variables, restores support for non-global symbols and types, eliminates
the need for many subsystem constructors, eliminates large per-subsystem
structures that caused many binary compatibility issues both for
monitoring applications (netstat) and kernel modules, removes the
per-function INIT_VNET_*() macros throughout the stack, eliminates the
need for vnet_symmap ksym(2) munging, and eliminates duplicate
definitions of virtualized globals under VIMAGE_GLOBALS.
Bump __FreeBSD_version and update UPDATING.
Portions submitted by: bz
Reviewed by: bz, zec
Discussed with: gnn, jamie, jeff, jhb, julian, sam
Suggested by: peter
Approved by: re (kensmith)
This dramatically pushing 99.9% interpolations and quantizations
error _below_ -180dB on 32bit dynamic range, resulting extremely
high quality conversion.
- Use BSPLINE interpolator for filter oversampling factor greater or
equal than 64 (log2 6).
Approved by: re (kib)
check missed this because cxgb's TOM is currently commented out of the build
system.
Submitted by: Navdeep Parhar <np at FreeBSD dot org>
Approved by: re (kensmith), kensmith (mentor temporarily unavailable)
the TCP syncache. This returns struct tcpopt to being private within the TCP
implementation, thus allowing it to be modified without ABI concerns.
The patch breaks the ABI. Bump __FreeBSD_version to 800103 accordingly. The cxgb
driver is the only TOE consumer affected by this change, and needs to be
recompiled along with the kernel.
Suggested by: rwatson
Reviewed by: rwatson, kmacy
Approved by: re (kensmith), kensmith (mentor temporarily unavailable)
USB CORE: busdma improvement
For single segment allocations the boundary field
of the BUSDMA tag should be zero. Currently all
single segment allocations are less than or equal
to 4096 bytes, so the limit does not kick in. If
any single segment USB allocations would be greater
than 4K, then it would be a problem.
Approved by: re (kensmith)
Obtained from: HPS
/boot/kernel/hptrr.ko
/etc/mail/*.cf
/lib/libcrypto.so.5
/usr/bin/ntpq
/usr/sbin/amd
/usr/sbin/iasl
/usr/sbin/ntpd
/usr/sbin/ntpdate
/usr/sbin/ntpdc
There does not appear to be any purpose to having these timestamps, and
they have the irritating consequence that the aforementioned files will
be different every time they are rebuilt.
After this commit, the only remaining build timestamps are in the kernel,
the boot loaders, /usr/include/osreldate.h (the year in the copyright
notice), and lib*.a (the timestamps on all of the included .o files).
Reviewed by: scottl (hptrr), gshapiro (sendmail), simon (openssl),
roberto (ntp), jkim (acpica)
Approved by: re (kib)
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.
Authentication and encryption are not implemented.
There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).
A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.
Drivers that support mesh networks right now are: ath, ral and mwl.
More information at: http://wiki.freebsd.org/WifiMesh
Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.
Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.
Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s
The default (64K) is too pessimistic for "new comm" hardware.
Also, this is bad because multiple controllers get limited by
the global tunable.
Reviewed by: scottl
Approved by: re (kensmith)
modularize it so that new transports can be created.
Add a transport for SATA
Add a periph+protocol layer for ATA
Add a driver for AHCI-compliant hardware.
Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.
The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.
ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.
This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.
Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.
The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.
Submitted by: scottl, mav
Approved by: re
MAXPHYS. Current ataahci driver memory allocation scheme includes only
64 items in DMA S/G table, and so not guarantied to support transactions
with more then 252K data.
Approved by: re (kensmith)
MFC after: 2 weeks
is invalid because the ioctl happens without prior open. The ioctl
got introduced to provide backward compatibility for extended
partitions, but it ended up not being used because it didn't work
as expected. Since there are no consumers of the ioctl and the
implementation is broken, the best fix is to remove the code
entirely.
Spotted by: phk
Approved by: re (kensmith)
This cause dramatic effect in overall precision and conversion quality
by pushing down most aliasing artifacts around -180 dB.
Spectrogram analysis/comparison:
http://people.freebsd.org/~ariff/z_comparison/z_28vs30/
- Guard against possible 64bit overflow during accumulation process by
slightly normalize and saturate sample and coefficient multiplication,
possible during extreme 32bit downsampling (eg. 380KHz -> 8KHz) with
custom preset that require more than ~7000 taps filter (which is
overkill).
- Add knobs through FEEDER_RATE_PRESETS to set dynamic range of filter
coefficients/accumulator and prefered polynomial interpolator:
COEFFICIENT_BIT:X
(where 1 <= X <= 30, default: 30)
ACCUMULATOR_BIT:X
(where 32 <= X <=64, default: 58)
INTERPOLATOR:I
(where I = ZOH, LINEAR, QUADRATIC, HERMITE, BSPLINE,
OPT32X, OPT16X, OPT8X, OPT4X, OPT2X)
Approved by: re (kib)
o add a new facility for components to register send+recv handlers
o ieee80211_send_action and ieee80211_recv_action now use the registered
handlers to dispatch operations
o rev ieee80211_send_action api to enable passing arbitrary data
o rev ieee80211_recv_action api to pass the 802.11 frame header as it may
be difficult to locate
o update existing IEEE80211_ACTION_CAT_BA and IEEE80211_ACTION_CAT_HT handling
o update mwl for api rev
Reviewed by: rpaulo
Approved by: re (kensmith)
- sysctl dev.acpi_hp.0.verbose to toggle debug output
- A modification so this can deal with different array lengths
when reading the CMI BIOS - now it works ok on HP Compaq nx7300
as well.
- Change behaviour to query only max_instance-1 CMI BIOS instances,
because all HPs seen so far are broken in that respect
(or there is a fundamental misunderstanding on my side, possible
as well). This way a disturbing ACPI Error Field exceeds Buffer
message is avoided.
- New bit to set on dev.acpi_hp.0.cmi_detail (0x8) to
also query the highest guid instance of CMI bios
acpi_hp.4:
- Document dev.acpi_hp.0.verbose sysctl in man page
- Document new bit for dev.acpi_hp.0.cmi_detail
- Add a section to manpage about hardware that has been reported
to work ok
Submitted by: Michael Gmelin <freebsdusb at bindone.de>
Approved by: re (kib)
MFC after: 2 weeks
via cpuctl(4) driver. Two new CPUCTL_MSRSBIT and CPUCTL_MSRCBIT ioctl(2)
calls treat the data field of the argument struct passed as a mask
and set/clear bits of the MSR register according to the mask value.
- Allow user to perform atomic bitwise AND and OR operaions on MSR registers
via cpucontrol(8) utility. Two new operations ("&=" and "|=") have been
added. The first one applies bitwise AND operaion between the current
contents of the MSR register and the mask, and the second performs bitwise
OR. The argument can be optionally prefixed with "~" inversion operator.
This allows one to mimic the "clear bit" behavior by using the command
like this:
cpucontrol -m 0x10&=~0x02 # clear the second bit of TSC MSR
Inversion operator support in all modes (assignment, OR, AND).
Approved by: re (kib)
MFC after: 1 month
- Document different semantics for ACPI_WMI_PROVIDES_GUID_STRING_METHOD
acpi_wmi.c:
- Modify acpi_wmi_provides_guid_string_method to return absolut number of
instances known for the given GUID.
acpi_hp.c:
- sysctl dev.acpi_hp.0.verbose to toggle debug output
- A modification so this can deal with different array lengths
when reading the CMI BIOS - now it works ok on HP Compaq nx7300
as well.
- Change behaviour to query only max_instance-1 CMI BIOS instances,
because all HPs seen so far are broken in that respect
(or there is a fundamental misunderstanding on my side, possible
as well). This way a disturbing ACPI Error Field exceeds Buffer
message is avoided.
- New bit to set on dev.acpi_hp.0.cmi_detail (0x8) to
also query the highest guid instance of CMI bios
acpi_hp.4:
- Document dev.acpi_hp.0.verbose sysctl in man page
- Document new bit for dev.acpi_hp.0.cmi_detail
- Add a section to manpage about hardware that has been reported
to work ok
Submitted by: Michael Gmelin, freebsdusb at bindone.de
Approved by: re (kib)
MFC after: 2 weeks
o new tx ack queue (not used right now)
o proxy-sta related changes (no proxy sta in driver)
o explicit dwds ena/dis (needed only with proxy sta)
o cleanup BA policy handling
o new ampdu aggressive mode support
o CFEnd use now controllable
Approved by: re (kensmith)
result was when the RX index wrapped it was converted into some
sort of gibberish and written into the RDT register, effectively
killing the RX side of the thing :)
Approved by: re
under certain environments. However give users chance to override
it when he/she surely knows his/her hardware works with Rx checksum
offload.
Reported by: Ulrich Spoerlein ( uqs <> spoerlein dot net )
MFC after: 1 week
Approved by: re (kensmith)
Giant was only used here to lock down a bit mask of allocated unit
numbers. Change the code to use its own mutex.
Reviewed by: hselasky
Approved by: re (kib)
inbound data waiting on a filedescriptor, such as a pipe or a socket,
for instance by using select(2), poll(2), kqueue(2), ioctl(FIONREAD)
etc.
But we have no way of finding out if written data have yet to be
disposed of, for instance, transmitted (and ack'ed!) to some remote
host, or read by the applicantion at the far end of the pipe.
The closest we get, is calling shutdown(2) on a TCP socket in
non-blocking mode, but this has the undesirable sideeffect of
preventing future communication.
Add a complement to FIONREAD, called FIONWRITE, which returns the
number of bytes not yet properly disposed of. Implement it for
all sockets.
Background:
A HTTP server will want to time out connections, if no new request
arrives within a certain period after the last transmitted response
has actually been sent (and ack'ed).
For a busy HTTP server, this timeout can be subsecond duration.
In order to signal to a load-balancer that the connection is truly
dead, TCP_RST will be the preferred method, as this avoids the need
for a RTT delay for FIN handshaking, with a client which, surprisingly
often, no longer at the remote IP number.
If a slow, distant client is being served a response which is big
enough to fill the window, but small enough to fit in the socket
buffer, the write(2) call will return immediately.
If the session timeout is armed at that time, all bytes in the
response may not have been transmitted by the time it fires.
FIONWRITE allows the timeout to check that no data is outstanding
on the connection, before it TCP_RST's it.
Input & Idea from: rwatson
Approved by: re (kib)
- Add support for devices that handle set and clear stall in hardware.
- Add missing get timestamp function
- Add more xfer flags
Submitted by: Hans Petter Selasky
Approved by: re (kib)
o add HAL_CAP_BSSIDMATCH to identify parts that have the support for
disabling bssid match
o honor capability for set/get rx filter
o use HAL_CAP_BSSIDMATCH in driver to decide whether to use the bssid
match disable or fall back to promisc mode
Reviewed by: rpaulo
Approved by: re (rwatson)
the value written to MSR register was always 0 regardless of value passed
by user.
- Use proper data pointer when performing AMD microcode update. Previously,
the pointer to user-space data has been provided instead, which is totally
incorrect.
Approved by: re (kib)
MFC after: 1 week
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
for the pmclog.
Reported by: Ryan Stone <rstone at sandvine dot com>
Tested by: Ryan Stone <rstone at sandvine dot com>
Sponsored by: Sandvine Incorporated
Note that this does not actually enable full-range i/o requests for
64 architectures, and is done now to update KBI only.
Tested by: pho
Reviewed by: jhb, bde (as part of the review of the bigger patch)
The Intel 2d driver calls modeset before reinstalling the handler on
a vt switch. This means that vblank status ends up getting cleared
after it has been setup. Restore saved values for the pipestat registers
rather than just wiping them out.
MFC after: 3 days
Use the vbl_lock when maniputlating the refcount. Eventually I want to
convert this to use our internal refcount code. Continue to use atomic
ops for manipulating vblank count since we access it often just for
reading.
MFC after: 3 days
- build ifmedia list based on phy->caps, not string comparisons.
- rebuild media list when a transceiver change is detected.
- return EOPNOTSUPP instead of ENXIO in cxgb_media_status.
Approved by: gnn (mentor)
MFC after: 2 weeks.
I tried re-ordering ether_ifdetach(), but this created a new race
where sometimes, when under heavy receive load (>1Mpps) and running
tcpdump, the machine would panic. At panic, the ithread was still in
the original (not dead) if_input() path, and was accessing stale BPF
data structs. By using a dying flag, I can close the interface prior
to if_detach() to be certain the interface cannot send packets up in
the middle of ether_ifdetach.
handling in order to reduce interrupt overhead which results in
better performance.
- Call ether_ifdetach(9) before stopping the controller and the
callouts detach in order to prevent active BPF listeners to clear
promiscuous mode which may lead to the tick callout being restarted
which will trigger a panic once it's actually gone.
- Add explicit IFF_DRV_RUNNING checking in order to prevent extra
link up/down events when using dhclient(8).
- Use the correct macro for deciding whether 2/3 of the available TX
descriptors are used.
- Wrap the RX fault printing in #ifdef CAS_DEBUG in order to not
unnecessarily frighten users and as debugging was the actual
intention. Real errors caused by these faults still will be
accumulated as input errors. It might be a good idea to later on
add driver specific counters for the faults though.
Submitted by: yongari (original patch)
longer useful for the FD_STYPE and FD_SOPTS ioctls to insist on being
issued on a writable file descriptor. Otherwise, there's no longer a
chance to set the drive type or options when a read-only medium is
present in the drive, as there is no way to obtain a writable fd then.
call ether_ifdetach(9) before stopping the controller and the
callouts. The consensus is that the latter is now safe to do and
should also solve the problem of active BPF listeners clearing
promiscuous mode can result in the tick callout being restarted
which in turn will trigger a panic once it's actually gone.
- honor parent DMA tag limitations, as man page requires,
- allow data buffer to be allocated within full 64bit address range, when
support is announced by hardware,
- add quirk, disabling 64bit addresses for broken chips, use it for MCP78.
This removes unnecessary PCI #includes dependency for systems with ATA
controllers living at non-PCI buses.
Submitted by: Piotr Ziecik
Obtained from: Semihalf
rlimit RLIMIT_SWAP that limits the amount of swap that may be reserved
for the uid.
The accounting information (charge) is associated with either map entry,
or vm object backing the entry, assuming the object is the first one
in the shadow chain and entry does not require COW. Charge is moved
from entry to object on allocation of the object, e.g. during the mmap,
assuming the object is allocated, or on the first page fault on the
entry. It moves back to the entry on forks due to COW setup.
The per-entry granularity of accounting makes the charge process fair
for processes that change uid during lifetime, and decrements charge
for proper uid when region is unmapped.
The interface of vm_pager_allocate(9) is extended by adding struct ucred *,
that is used to charge appropriate uid when allocation if performed by
kernel, e.g. md(4).
Several syscalls, among them is fork(2), may now return ENOMEM when
global or per-uid limits are enforced.
In collaboration with: pho
Reviewed by: alc
Approved by: re (kensmith)
the PHYs as some PHY drivers use it (but probably shouldn't). How
gem(4) has worked with brgphy(4) on powerpc without this so far is
unclear to me.
- Introduce a dying flag which is set during detach and checked in
gem_ioctl() in order to prevent active BPF listeners to clear
promiscuous mode which may lead to the tick callout being restarted
which will trigger a panic once it's actually gone.
- In gem_stop() reset rather than just disable the transmitter and
receiver in order to ensure we're not unloading DMA maps still in
use by the hardware. [1]
- The blanking time is specified in PCI clocks so we should use twice
the value when operating at 66MHz.
- Spell some 2 as ETHER_ALIGN and a 19 as GEM_STATUS_TX_COMPLETION_SHFT
to make the actual intentions clear.
- As we don't unload the peak attempts counter ignore its overflow
interrupts.
- Remove a stale setting of a variable to GEM_TD_INTERRUPT_ME which
isn't used afterwards.
- For optimum performance increment the TX kick register in multiples
of 4 if possible as suggested by the documentation.
- Partially revert r164931; drivers should only clear the watchdog
timer if all outstanding TX descriptors are done.
- Fix some debugging strings.
- Add a missing BUS_DMASYNC_POSTWRITE in gem_rint().
- As the error paths in the interrupt handler are generally unlikely
predict them as false.
- Add support for the SBus version of the GEM controller. [2]
- Add some lock assertions.
- Improve some comments.
- Fix some more or less cosmetic issues in the code of the PCI front-end.
- Change some softc members to be unsigned where more appropriate and
remove unused ones.
Approved by: re (kib)
Obtained from: NetBSD (partially) [2], OpenBSD [1]
MFC after: 2 weeks
- Support for 10G-PCIE*-8B*-C (dual-port CX4) NICs
- For dual-port NICs, f/w failover is now a few microsecs
instead of a few millisecs.
- On failover, f/w sends RARP broadcast to make the change
immediately known to the network
- Fixed a bug observed on IBM X3 architecture where
some spurious ecrc errors would be reported when OS enabled
ecrc support.
Sponsored by: Myricom Inc.
* Driver for ACPI HP extra functionations, which required
ACPI WMI driver.
Submitted by: Michael <freebsdusb at bindone.de>
Approved by: re
MFC after: 2 weeks
a pointer to an ifaddr matching the passed socket address, returns a
boolean indicating whether one was present. In the (near) future,
ifa_ifwithaddr() will return a referenced ifaddr rather than a raw
ifaddr pointer, and the new wrapper will allow callers that care only
about the boolean condition to avoid having to free that reference.
MFC after: 3 weeks
Note that I also added the usbdev to the list, because the 8813 version
is not yet known there. I might have twisted the sorting there but because
8813 comes before 8818, I added it before that (with _8813 to differentiate)
the item.
PR: 135628
Submitted by: Yoshikazu GOTO <goto at on-link dot jp>
Approved by: imp (mentor, implicit)
To detect which controller is ICH based one, add a new member
variable ich to struct fxp_ident and move the struct to
if_fxpvar.h. Since I've faked controller revision, don't allow
microcode loading for ICH based controllers.
With this change all ICH based controllers will have WOL and Rx
checksum offload capability.
PR: kern/135451
Tested by: Alexey Shuvaev ( shuvaev <> physik dot uni-wuerzburg dot de ),
pluknet ( pluknet <> gmail dot com ),
Gary Jennejohn ( gary.jennejohn <> freenet dot de )
not allow multicast filter programming when controller is busy to
send/receive frames. So it used to mark need_mcsetup bit and defer
multicast filter programming until controller becomes idle state.
To detect when the controller is idle fxp(4) relied on Tx
completion interrupt with NOP command and fxp_start_body and
fxp_intr_body had to see whether pending multicast filter
programming was requested. This resulted in very complex logic and
sometimes it did not work as expected.
Since the controller should be in idle state before any multicast
filter modifications I changed it to reinitialize the controller
whenever multicast filter programming is required. This is the same
way what OpenBSD and NetBSD does. Also I added IFF_DRV_RUNNING
check in ioctl handler so controller would be reinitialized only if
it is absolutely needed.
With this change I guess we can remove fxp(4) DELAY hack in ifioctl
for IPv6 case.
upper stack in fxp_start_body().
fxp(4) drops driver lock in Rx path so check the fxp(4) is still
running after reacquiring driver lock in Rx path. Also don't
invoke fxp_intr_body if fxp(4) is not running. With this change
there is no need to set suspend bit in device attach phase.
hardware reset in attach phase. Selective reset does not clear
configured parameters so I think full hardware reset is required.
To prevent PCI bus lock-up, do selective reset first which will get
off the controller from PCI bus and request software reset after
selective reset. Software reset will unmask interrupts so disable
it after the reset.
common mbuf dma tag for both Tx and Rx path but Rx buffer should
have single DMA segment and maximum buffer size of the segment
should be less than MCLBYTES.
fxp(4) also have to check Tx completion status which was updated by
DMA so we need BUS_DMASYNC_PREREAD and BUS_DMASYNC_POSTWRITE
synchronization in Tx path. Fix all misuse of bus_dmamap_sync(9) in
fxp(4). I guess this change shall fix occasional driver breakage in
PAE environments.
While I'm here add error messages of dma tag/buffer creation and
correct messages.
Intel agrees with my reading of the docs, make it so for all G4X chips.
The new register also has a 32 bit width as opposed to 24 bits. Fix
things up so that the counters roll over properly.
MFC after: 3 days
- remove mbuf iovec - useful, but adds too much complexity when isolated to
the driver
- remove driver private caching - insufficient benefit over UMA to justify
the added complexity and maintenance overhead
- remove separate logic for managing multiple transmit queues, with the
new drbr routines the control flow can be made to much more closely resemble
legacy drivers
- remove dedicated service threads, with per-cpu callouts one can get the same
benefit much more simply by registering a callout 1 tick in the future if there
are still buffered packets
- remove embedded mbuf usage - Jeffr's changes will (I hope) soon be integrated
greatly reducing the overhead of using kernel APIs for reference counting
clusters
- add hysteresis to descriptor coalescing logic
- add coalesce threshold sysctls to allow users to decide at run-time
between optimizing for forwarding / UDP or optimizing for TCP
- add once per second watchdog to effectively close the very rare races
occurring from coalescing
- incorporate Navdeep's changes to the initialization path required to
convert port and adapter locks back to ordinary mutexes (silencing BPF
LOR complaints)
- enable prefetches in get_packet and tx cleaning
Reviewed by: navdeep@
MFC after: 2 weeks
by if_free (w/o doing if_attach); move ifq_attach to if_alloc and
rename ifq_attach/detach to ifq_init/ifq_delete to better identify
their purpose
Reviewed by: jhb, kmacy
DP83065 Saturn Gigabit Ethernet controllers. These are the successors
of the Sun GEM controllers and still have a similar but extended transmit
logic. As such this driver is based on gem(4).
Thanks to marcel@ for providing a Sun Quad GigaSwift Ethernet UTP (QGE)
card which was vital for getting this driver to work on architectures
not using Open Firmware.
Approved by: re (kib)
MFC after: 2 weeks
FEEDER_RATE_PRESET "OVERSAMPLING_FACTOR:X .. .." where
X = log2(oversampling factor).
- Lower down default filter oversampling factor from 128
(log2 = 7) to 32 (log2 = 5), saving worth of 80 Kb.
The use of better polynomial interpolator will raise
its conversion quality/accuracy to match (or slightly
better) with previous settings.
- Bump driver version.
coefficients quality:
- Linear interpolator for oversampling factor larger and equal
than 4096 (log2 = 12).
- Quadratic interpolator for oversampling factor larger and equal
than 256 (log2 = 8).
Default oversampling factor (128 ~ log2 = 7) will use OPT32X, which
provides better accuracy.
Characters between 0x07 and 0x0d are now also mapped, which means we can
display almost 256 different characters. Also remap certain types of
dashes and quotes, which means we can finally read our manual pages
without red question marks in them.
Submitted by: Christoph Mallon
of the DP83861 and DP83891.
- Reset the PHY during attach so it's in a known state.
- Add a comment describing why we hardwire 10baseT support in
the BMSR.
- Always explicitly set IFM_HDX for half-duplex. [1]
Obtained from: OpenBSD [1]
MFC after: 2 weeks
Add a small Unicode-to-CP437 remapping table to at least demonstrate
that the terminal emulator is perfectly capable of handling UTF-8. This
will of course break if the user loads a different font map, but it at
least allows people to give it a try.
I can now see the box drawing in dialog(1) and the arrows in mutt(1)
correctly.
so that it isn't exposured unless needed. In particular this means
that it's easier to tune the memory layout based on board details.
While here, remove inclusion of <machine/intr.h> from mvreg.h. This
also contains exposure to SoC specifics in MI drivers, because NIRQ
depends on the SoC.
in symtab_get method symtab parameter is made constant as this reflects
actual intention and usage of the method
Reviewed by: imp, current@
Approved by: jhb (mentor)
- Preallocate some memory for ACPI tasks early enough. We cannot use
malloc(9) any more because spin mutex may be held here. The reserved
memory can be tuned via debug.acpi.max_tasks tunable or ACPI_MAX_TASKS
in kernel configuration. The default is 32 tasks.
- Implement a custom taskqueue_fast to wrap the new memory allocation.
This implementation is not the fastest in the world but we are being
conservative here.
routine and save the resources using a chipset-data structure. Use these
preallocated resources to setup resources for the SATA channels to avoid
asking the PCI bus to allocate the same BAR multiple times.
Tested by: bms
MFC after: 1 week
controller. These controllers are also known as L1C(AR8131) and
L2C(AR8132) respectively. These controllers resembles the first
generation controller L1 but usage of different descriptor format
and new register mappings over L1 register space requires a new
driver. There are a couple of registers I still don't understand
but the driver seems to have no critical issues for performance and
stability. Currently alc(4) supports the following hardware
features.
o MSI
o TCP Segmentation offload
o Hardware VLAN tag insertion/stripping
o Tx/Rx interrupt moderation
o Hardware statistics counters(dev.alc.%d.stats)
o Jumbo frame
o WOL
AR8131/AR8132 also supports Tx checksum offloading but I disabled
it due to stability issues. I'm not sure this comes from broken
sample boards or hardware bugs. If you know your controller works
without problems you can still enable it. The controller has a
silicon bug for Rx checksum offloading, so the feature was not
implemented.
I'd like to say big thanks to Atheros. Atheros kindly sent sample
boards to me and answered several questions I had.
HW donated by: Atheros Communications, Inc.
driver should read updated status back after issuing a SCB command.
To send a command to controller and read updated status back,
driver should synchronize both memory read and write operations
with device. Fix bus_dmamap_sync operation specifier used in
fxp_dma_wait() by adding both memory read and memory write
operations.
a _BBN value of 0 if it was for the first bridge encountered since some
older systems returned _BBN of 0 for all bridges. However, some newer
systems enumerate bridges with non-zero _BBN before bus 0 which is
perfectly valid. Handle both cases by trusting the first bridge that has
a _BBN of 0 and falling back to reading from non-standard config registers
only for subsequent bridges with a _BBN of 0. We also only perform this
check for segment (domain) 0. We assume that _BBN is always correct
for segments other than 0.
Tested by: Josef Moellers josef.moellers at fujitsu
MFC after: 1 week
- The return value should be a signed integer, because -1 means failure.
- The c variable should be unsigned, to force it to be zero-extended
when returned.
Reported by: Andreas Tobler <andreast-list fgznet ch>
the ROUTETABLES kernel option thus there is no need to include opt_route.h
anymore in all consumers of vnet.h and no longer depend on it for module
builds.
Remove the hidden include in flowtable.h as well and leave the two
explicit #includes in ip_input.c and ip_output.c.
For a slightly thorough explaination, please refer to
[1] http://people.freebsd.org/~ariff/SOUND_4.TXT.html .
Summary of changes includes:
1 Volume Per-Channel (vpc). Provides private / standalone volume control
unique per-stream pcm channel without touching master volume / pcm.
Applications can directly use SNDCTL_DSP_[GET|SET][PLAY|REC]VOL, or for
backwards compatibility, SOUND_MIXER_PCM through the opened dsp device
instead of /dev/mixer. Special "bypass" mode is enabled through
/dev/mixer which will automatically detect if the adjustment is made
through /dev/mixer and forward its request to this private volume
controller. Changes to this volume object will not interfere with
other channels.
Requirements:
- SNDCTL_DSP_[GET|SET][PLAY|REC]_VOL are newer ioctls (OSSv4) which
require specific application modifications (preferred).
- No modifications required for using bypass mode, so applications
like mplayer or xmms should work out of the box.
Kernel hints:
- hint.pcm.%d.vpc (0 = disable vpc).
Kernel sysctls:
- hw.snd.vpc_mixer_bypass (default: 1). Enable or disable /dev/mixer
bypass mode.
- hw.snd.vpc_autoreset (default: 1). By default, closing/opening
/dev/dsp will reset the volume back to 0 db gain/attenuation.
Setting this to 0 will preserve its settings across device
closing/opening.
- hw.snd.vpc_reset (default: 0). Panic/reset button to reset all
volume settings back to 0 db.
- hw.snd.vpc_0db (default: 45). 0 db relative to linear mixer value.
2 High quality fixed-point Bandlimited SINC sampling rate converter,
based on Julius O'Smith's Digital Audio Resampling -
http://ccrma.stanford.edu/~jos/resample/. It includes a filter design
script written in awk (the clumsiest joke I've ever written)
- 100% 32bit fixed-point, 64bit accumulator.
- Possibly among the fastest (if not fastest) of its kind.
- Resampling quality is tunable, either runtime or during kernel
compilation (FEEDER_RATE_PRESETS).
- Quality can be further customized during kernel compilation by
defining FEEDER_RATE_PRESETS in /etc/make.conf.
Kernel sysctls:
- hw.snd.feeder_rate_quality.
0 - Zero-order Hold (ZOH). Fastest, bad quality.
1 - Linear Interpolation (LINEAR). Slightly slower than ZOH,
better quality but still does not eliminate aliasing.
2 - (and above) - Sinc Interpolation(SINC). Best quality. SINC
quality always start from 2 and above.
Rough quality comparisons:
- http://people.freebsd.org/~ariff/z_comparison/
3 Bit-perfect mode. Bypasses all feeder/dsp effects. Pure sound will be
directly fed into the hardware.
4 Parametric (compile time) Software Equalizer (Bass/Treble mixer). Can
be customized by defining FEEDER_EQ_PRESETS in /etc/make.conf.
5 Transparent/Adaptive Virtual Channel. Now you don't have to disable
vchans in order to make digital format pass through. It also makes
vchans more dynamic by choosing a better format/rate among all the
concurrent streams, which means that dev.pcm.X.play.vchanformat/rate
becomes sort of optional.
6 Exclusive Stream, with special open() mode O_EXCL. This will "mute"
other concurrent vchan streams and only allow a single channel with
O_EXCL set to keep producing sound.
Other Changes:
* most feeder_* stuffs are compilable in userland. Let's not
speculate whether we should go all out for it (save that for
FreeBSD 16.0-RELEASE).
* kobj signature fixups, thanks to Andriy Gapon <avg@freebsd.org>
* pull out channel mixing logic out of vchan.c and create its own
feeder_mixer for world justice.
* various refactoring here and there, for good or bad.
* activation of few more OSSv4 ioctls() (see [1] above).
* opt_snd.h for possible compile time configuration:
(mostly for debugging purposes, don't try these at home)
SND_DEBUG
SND_DIAGNOSTIC
SND_FEEDER_MULTIFORMAT
SND_FEEDER_FULL_MULTIFORMAT
SND_FEEDER_RATE_HP
SND_PCM_64
SND_OLDSTEREO
Manual page updates are on the way.
Tested by: joel, Olivier SMEDTS <olivier at gid0 d org>, too many
unsung / unnamed heroes.
in Freescale system-on-chip devices.
The following algorithms and schemes are currently supported:
- 3DES, AES, DES
- MD5, SHA1, SHA256, SHA384, SHA512
Reviewed by: philip
Obtained from: Freescale, Semihalf
These two drivers seem to be the last consumers of clists. clists are
quite overengineered for simple circular buffers, so I'm adding similar
buffer management routines to the kbd and kbdmux drivers. The input
buffer is now part of the softc structures, instead of having
dynamically allocated cblocks.
ICIDU NI-707503 which is donated by Nick Hibma (great thanks!). Though
it has a MAXIM RF (0x8) there's some success reports with using GCT RF
(0x9) codes and it worked well for ICIDU NI-707503 too. So codes for
MAXIM and GCT RFs are integrated.
Before this commit, if I rememeber correctly, MAXIM RF is never tested
that it seems it's a first report working with FreeBSD.
- always maintain byte/mcast/drop stats via drbr
- move #define of IFNET_BUF_RING so that its picked
up by all files in the driver
- conditionalize IFNET_BUF_RING on the FreeBSD_version
bump just after it appeared in the tree.
Sponsored by: Myricom Inc.
These controllers use newer descriptor format and the new descriptor
format uses status LE to indicate the status of checksum. Rx
checksummed value used in previous controllers were very cryptic
and I failed to understand how to use them. In addition most
controllers in previous generations had Rx checksum offloading bug.
While I'm here introduce a MSK_FLAG_NORX_CSUM flag to bypass
checking Rx checksum offloading as Yukon FE+ A0 has status LE bug.
this feature hardware automatically computes TCP/UDP payload
offset. Introduce MSK_FLAG_AUTOTX_CSUM to mark the capability.
Yukon Extreme B0 revision is known to have a silicon for the
feature so disable it. Yukon Extreme B0 still can do Tx checksum
offloading but CPU have to compute TCP/UDP payload offset. To
enable traditional checksum offloading, disable automatic Tx
checksum calculation capability.
Yukon Extreme A0 revision could not use store-and-forward mode for
jumbo frames(silicon bug) so disable Tx checksum offloading for
jumbo frames.
I believe controllers that have MSK_FLAG_AUTOTX_CSUM capability or
new descriptor format do not have Tx checksum offload bug so
disable checksum offloading workaround for for short frames.
Tested by: jhb, Warren Block ( wblock <> wonkity dot com )
Yukon Extreme uses new descriptor format for TSO and has Tx frame
parser which greatly reduces CPU cycles spent in computing TCP/UDP
payload offset calculation in Tx checksum offloading path. The new
descriptor format also removed TCP/UDP payload computation for TSO
which in turn results in better TSO performance. It seems Yukon
Extreme has a lot of new (unknown) features but only basic
offloading is supported at this time. So far there are two known
issues.
o Sometimes Rx overrun errors happen when pulling data over
gigabit link. Running over 100Mbps seem to ok.
o Ethernet hardware address shows all-zeroed value on 88E8070.
Assigning ethernet address with ifconfig is necessary to make it
work.
Support for Yukon Extreme is not perfect but it would be better
than having a non-working device. Special thanks to jbh who fixed
several bugs of initial patch.
Tested by: jhb, Warren Block ( wblock <> wonkity dot com )
- Each socket upcall is now invoked with the appropriate socket buffer
locked. It is not permissible to call soisconnected() with this lock
held; however, so socket upcalls now return an integer value. The two
possible values are SU_OK and SU_ISCONNECTED. If an upcall returns
SU_ISCONNECTED, then the soisconnected() will be invoked on the
socket after the socket buffer lock is dropped.
- A new API is provided for setting and clearing socket upcalls. The
API consists of soupcall_set() and soupcall_clear().
- To simplify locking, each socket buffer now has a separate upcall.
- When a socket upcall returns SU_ISCONNECTED, the upcall is cleared from
the receive socket buffer automatically. Note that a SO_SND upcall
should never return SU_ISCONNECTED.
- All this means that accept filters should now return SU_ISCONNECTED
instead of calling soisconnected() directly. They also no longer need
to explicitly clear the upcall on the new socket.
- The HTTP accept filter still uses soupcall_set() to manage its internal
state machine, but other accept filters no longer have any explicit
knowlege of socket upcall internals aside from their return value.
- The various RPC client upcalls currently drop the socket buffer lock
while invoking soreceive() as a temporary band-aid. The plan for
the future is to add a new flag to allow soreceive() to be called with
the socket buffer locked.
- The AIO callback for socket I/O is now also invoked with the socket
buffer locked. Previously sowakeup() would drop the socket buffer
lock only to call aio_swake() which immediately re-acquired the socket
buffer lock for the duration of the function call.
Discussed with: rwatson, rmacklem
using bus_dmamap_load_mbuf_sg() on it. This
prevents data corruption when the mxge MTU is
between 4076 and 8172 on machines with 4KB
pages and MXGE_VIRT_JUMBOS is in use (which it
isn't, in -current or -stable)
mic inputs. I have no idea what for it was made that time, but now I have
several reports that it should be removed to make microphones work. If
this quirk is still required for some systems then they should be identified
and specified explicitly.
Because we only support a single argument to tf_param, use 16 bits for
the pitch and 16 bits for the duration. While there, make the argument
unsigned. There isn't a single param call that needs a signed integer.
Submitted by: danfe (modified)
part identified as Sunplus Technology Inc. This
happens to sit in a Rosewill RX81U-ES-25A 2.5" SATA
to USB 2.0 external enclosure.
Reviewed by: Hans Petter Selasky
CPU for too long period than necessary. Additively, interfaces are kept
polled (in the tick) even if no more packets are available.
In order to avoid such situations a new generic mechanism can be
implemented in proactive way, keeping track of the time spent on any
packet and fragmenting the time for any tick, stopping the processing
as soon as possible.
In order to implement such mechanism, the polling handler needs to
change, returning the number of packets processed.
While the intended logic is not part of this patch, the polling KPI is
broken by this commit, adding an int return value and the new flag
IFCAP_POLLING_NOCOUNT (which will signal that the return value is
meaningless for the installed handler and checking should be skipped).
Bump __FreeBSD_version in order to signal such situation.
Reviewed by: emaste
Sponsored by: Sandvine Incorporated
The system hostname is now stored in prison0, and the global variable
"hostname" has been removed, as has the hostname_mtx mutex. Jails may
have their own host information, or they may inherit it from the
parent/system. The proper way to read the hostname is via
getcredhostname(), which will copy either the hostname associated with
the passed cred, or the system hostname if you pass NULL. The system
hostname can still be accessed directly (and without locking) at
prison0.pr_host, but that should be avoided where possible.
The "similar information" referred to is domainname, hostid, and
hostuuid, which have also become prison parameters and had their
associated global variables removed.
Approved by: bz (mentor)
I don't want people to override the mutex when allocating a TTY. It has
to be there, to keep drivers like syscons happy. So I'm creating a
tty_alloc_mutex() which can be used in those cases. tty_alloc_mutex()
should eventually be removed.
The advantage of this approach, is that we can just remove a function,
without breaking the regular API in the future.
Calculate the exact number of vectors we'll use before calling
pci_alloc_msix. Don't grab nine all the time.
Call cxgb_setup_interrupts once per T3, not once per port. Ditto
for cxgb_teardown_interrupts.
Don't leak resources when interrupt setup fails in the middle.
Obtained from: Navdeep Parhar
MFC after: 10 days
- add key mappings for fn keys
- byte swapping for certain models
- Fix leds for keyboards which require an ID byte for the HID output structures
Submitted by: Hans Petter Selasky
to dequeue a packet.
The tx path was trying to ensure that enough Xenbus TX ring slots existed but
it didn't check to see whether the mbuf TX ring slots were also available.
They get freed in xn_txeof() which occurs after transmission, rather than earlier
on in the process. (The same happens under Linux too.)
Due to whatever reason (CPU use, scheduling, memory constraints, whatever) the
mbuf TX ring may not have enough slots free and would allocate slot 0. This is
used as the freelist head pointer to represent "free" mbuf TX ring slots; setting
this to an actual mbuf value rather than an id crashes the code.
This commit introduces some basic code to track the TX mbuf ring use and then
(hopefully!) ensures that enough slots are free in said TX mbuf ring before it
enters the actual work loop.
A few notes:
* Similar logic needs to be introduced to check there are enough actual slots
available in the xenbuf TX ring. There's some logic which is invoked earlier
but it doesn't hard-check against the number of available ring slots.
Its trivial to do; I'll do it in a subsequent commit.
* As I've now commented in the source, it is likely possible to deadlock the
driver under certain conditions where the rings aren't receiving any changes
(which I should enumerate) and thus Xen doesn't send any further software
interrupts. I need to make sure that the timer(s) are running right and
the queues are periodically kicked.
PR: 134926
Slot 0 must always remain "free" and be a pointer to the first free entry in the
mbuf descriptor list. It is thus an error to have code allocate or push slot 0
back into the list.
get a quick snapshot of the kernel's symbol table including the symbols
from any loaded modules (the symbols are all merged into one symbol
table). Unlike like other implementations, this ksyms driver maps
memory in the process memory space to store the snapshot at the time
/dev/ksyms is opened. It also checks to see if the process has already
a snapshot open and won't allow it to open /dev/ksyms it again until it
closes first. This prevents kernel and process memory from being
exhausted. Note that /dev/ksyms is used by the lockstat(1) command.
Reviewed by: gallatin kib (freebsd-arch)
Approved by: gnn (mentor)
severe silicon bugs that can't handle VLAN hardware tagging as well
as status LE writeback bug. The status LE writeback bug is so
critical we can't trust status word of received frame. To accept
frames on Yukon FE+ A0 msk(4) just do minimal check for received
frames and pass them to upper stack. This means msk(4) can pass
corrupted frames to upper layer. You have been warned!
Also I supposed RX_GMF_FL_THR to be 32bits register but Linux
driver treated it as 16bit register so follow their leads. At least
this does not seem to break msk(4) on Yukon FE+.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
Yukon FE+ is fast ethernet controller and uses new descriptor
format. Since I don't have this controller, the support code was
written from guess and various feedback from enthusiastic users.
Thanks to all users who patiently tested my initial patches.
Special thanks to Tanguy Bouzeloc who fixed critical bug of initial
patch.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
The GM_GP_CTRL register may have stale content from previous link
information so clearing it will make hardware update the register
correctly when it established a valid link.
While I'm here remove stale comment.
does not guarantee established link. Also 1000baseT link report for
fast ethernet controller is not valid one so make sure gigabit link
is allowed for this controller.
Whenever we lost link, check whether Rx/Tx MACs were enabled. If both
MAC are not active, do not try to disable it again.
mark controller's capability. Controllers that have jumbo frame
support sets MSK_FLAG_JUMBO, and controllers that does not support
checksum offloading for jumbo frames will set MSK_FLAG_JUMBO_NOCSUM.
For Fast Ethernet controllers it will set MSK_FLAG_FASTETHER and it
would be used in link state handling.
While here, disable Tx checksum offloading if jumbo frame is used
on controllers that does not have Tx checksum offloading capability
for jumbo frame(e.g. Yukon EC Ultra).
FE+ controller. Due to the severe silicon bugs for Yukon FE+,
88E3016 seems to require more workarounds. However I'm not sure
whether the workaround is PHY specific or only applicable to Yukon
FE+. The datasheet for the PHY is publicly available but it lacks
several details for the workaround used in this change. The
workaround information was obtained from Linux. Many thanks to
Yukon FE+ users who helped me add 88E3016 support.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
advertisement register. Some PHYs such as 88E3016 requires NEXT
Page capability to establish valid link. Also set protocol selector
field which is read only but it makes the intention clearer.
is valid only for auto-negotiation case so check the bit if we know
auto-negotiation is active. While I'm here explicitly checks
current speed with speed mask and set IFM_NONE if resolved speed
is unknown.
checks extended status register to see whether the PHY is fast
ethernet or not. This removes a lot of checks for specific PHY
models and it makes easy to add more PHYs to e1000phy(4).
While I'm here remove setting mii_anegticks as it is set with
mii_phy_add_media().
Remove PAGE_SIZE alignment used in Rx buffer DMA tag creation. The
alignment restriction was used in old local jumbo allocator and
nfe(4) switched to UMA backed page allocator for jumbo frame.
This change should fix jumbo buffer allocation failure.
Reported by: Pascal Braun ( pascal.braun <> continum dot net )
only if prepping the adapter failed.
Slight adjustment to comments.
Fix a bug whereby downing the interface didn't preven it from
processing packets.
Submitted by: Navdeep Parhar
MFC after: 1 week
Some hardware easily comes out of sync with regard to whether the current or
the next control transfer should be stalled, if a stall command is always
issued before receiving the SETUP packet. After this patch the stall command
will only be issued when a transfer should actually be stalled.
Submitted by: Hans Petter Selasky
1) Add a sysctl that will say what type of PHYs exist on the card.
2) Fix a bug that occurs when an AEL 2005 PHY resets without a transciever
in the card.
3) Unify the PHY link detection code.
Obtained from: Navdeep Parhar
MFC after: 10 days
and down more cleanly. This addresses a problem where if we have the
link flap during boot the driver would lock up the system.
Reviewed by: jhb
MFC after: 1 week
thread. Multiple RAID events in quick succession can cause an additional
bus rescan to be scheduled before an earlier scan has completed. In this
case the driver was attempting to use the same CCB storage for two requests.
PR: kern/130330
Reviewed by: Riccardo Torrini riccardo.torrini | esaote com
MFC after: 1 week
o Header file cleanup.
o bus_dma(9) conversion.
- Removed all consumers of vtophys(9) and converted to use
bus_dma(9).
- 64bit DMA support was disabled because DP83821 is not capable
of handling the DMA request. 64bit DMA request on DP83820
requires different descriptor structures and it's hard to
dynamically change descriptor format at run time so I disabled
it. Note, this is the same behavior as previous one but
previously nge(4) didn't explicitly disable 64bit mode on
DP83820.
- Added Tx/Rx descriptor ring alignment requirements(8 bytes
alignment).
- Limit maximum number of Tx DMA segments to 16. In fact,
controller does not seem to have limitations on number of Tx
DMA segments but 16 should be enough for most cases and
m_collapse(9) will handle highly fragmented frames without
consuming a lot of CPU cycles.
- Added Rx buffer alignment requirements(8 bytes alignment). This
means driver should fixup received frames to align on 16bits
boundary on strict-alignment architectures.
- Nuked driver private data structure in descriptor ring.
- Added endianness support code in Tx/Rx descriptor access.
o Prefer faster memory mapped register access to I/O mapped access.
Added fall-back mechanism to use alternative register access.
The hardware supports both memory and I/O mapped access.
o Added suspend/resume methods but it wasn't tested as controller I
have does not support PCI PME.
o Removed swap argument in nge_read_eeprom() since endianness
should be handled after reading EEPROM.
o Implemented experimental 802.3x full-duplex flow-control. ATM
it was commented out but will be activated after we have generic
flow-control framework in mii(4) layer.
o Rearranged promiscuous mode settings and simplified logic.
o Always disable Rx filter prior to changing Rx filter functions as
indicated in DP83820/DP83821 datasheet.
o Added an explicit DELAY in timeout loop of nge_reset().
o Added a sysctl variable dev.nge.%d.int_holdoff to control
interrupt moderation. Valid ranges are 1 to 255(default 1) in
units of 100us. The actual delivery of interrupt would be delayed
based on the sysctl value. The interface has to be brought down
and up again before a change takes effect. With proper tuning
value, users do not need to resort to polling(4) anymore.
o Added ALTQ(4) support.
o Added missing IFCAP_VLAN_HWCSUM as nge(4) can offload Tx/Rx
checksum calculation on VLAN tagged frames as well as VLAN tag
insertion/stripping. Also add IFCAP_VLAN_MTU capability as nge(4)
can handle VLAN tagged oversized frames.
o Fixed media header length for VLAN.
o Rearranged nge_detach routine such that it's now used for general
clean-up routine.
o Enabled MWI.
o Accessing EEPROM takes very long time so read 6 bytes ethernet
address with one call instead of 3 separate accesses.
o Don't set if_mtu in device attach, it's already set in
ether_ifattach().
o Don't do any special things for TBI interface. Remove TBI
specific media handling in the driver and have gentbi(4) handle
it. Add glue code to read/write TBI PHY registers in miibus
method. This change removes a lot of PHY handling code in driver
and now its functionality is handled by mii(4).
o Alignment fixup code is now applied only for strict-alignment
architectures. Previously the code was applied for all
architectures except i386. With this change amd64 will get
instant Rx performance boost.
o When driver fails to allocate a new mbuf, update if_qdrops so
users can see what was wrong in Rx path.
o Added a workaround for a hardware bug which resulted in short
VLAN tagged frames(e.g. ARP) was rejected as if runt frame was
received. With this workaround nge(4) now accepts the short VLAN
tagged frame and nge(4) can take full advantage of hardware VLAN
tag stripping. I have no idea how this bug wasn't known so far,
without the workaround nge(4) may never work on VLAN
environments.
o Fixed Rx checksum offload logic such that it now honors active
interface capability configured with ifconfig(8).
o In nge_start()/nge_txencap(), always leave at least one free
descriptor as indicated in datasheet. Without this the hardware
would be confused with ring descriptor structure(e.g. no clue
for the end of descriptor ring).
o Removed dead-code that checks interrupts on PHY hardware. The
code was designed to detect link state changes but it was
disabled as driving nge_tick clock would break auto-negotiation
timer. This code is no longer needed as nge(4) now uses mii(4)
and link state change handling is done with mii callback.
o Rearranged ethernet address programming logic such that it works
on strict-alignment architectures.
o Added IFCAP_VLAN_HWTAGGING/IFCAP_VLAN_HWCSUM handler in
nge_ioctl() such that the functionality is configurable with
ifconfig(8). DP83820/DP83821 can do checksum offload for VLAN
tagged frames so enable Tx/Rx checksum offload for VLAN
interfaces.
o Simplified IFCAP_POLLING selection logic in nge_ioctl().
o Fixed module unload panic when bpf listeners are active.
o Tx/Rx descriptor ring address uses 64bit DMA address for
readability. High address part of DMA would be 0 as nge(4)
disabled 64bit DMA transfers so it's ok for DP83821.
o Removed volatile keyword in softc as bus_dmamap_sync(9) should
take care of this.
o Removed extra driver private structures in descriptor ring. These
extra elements are not part of descriptor structure. Embedding
private driver structure into descriptor ring is not good idea
as its size may be different on 32bit/64bit architectures.
o Added miibus_linkchg method handler to catch link state changes.
o Removed unneeded nge_ifmedia in softc. All TBI access is handled
in gentbi(4). There is no difference between TBI and non-TBI case
now.
o Removed "gigabit link up" message handling in nge_tick. Link
state change notification is already performed by mii(4) and
checking link state by accessing PHY registers in periodic timer
handler of driver is wrong. All link state and speed/duplex
monitoring should be handled in PHY driver.
o Use our own timer for watchdog instead of if_watchdog/if_timer
interface.
o Added hardware MAC statistics counter, users canget current MAC
statistics from dev.nge.%d.stats sysctl node(%d is unit number of
a device).
o Removed unused macros, NGE_LASTDESC, NGE_MODE, NGE_OWNDESC,
NGE_RXBYTES.
o Increased number of Tx/Rx descriptors from 128 to 256. From my
experience on gigabit ethernet controllers, number of descriptors
should be 256 or higher to get an optimal performance on gigabit
link.
o Increased jumbo frame length to 9022 bytes to cope with other
gigabit ethernet drivers. Experimentation shows no problems with
9022 bytes.
o Removed unused member variables in softc.
o Switched from bus_space_{read|write}_4 to bus_{read|write}_4.
o Added support for WOL.
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
bug referencing a destroyed lock within TX callbacks during device
detach.
Submitted by: hps (original version)
Tested by: Lucius Windschuh <lwindschuh at googlemail.com>
possible future I-cache coherency operation can succeed. On ARM
for example the L1 cache can be (is) virtually mapped, which
means that any I/O that uses temporary mappings will not see the
I-cache made coherent. On ia64 a similar behaviour has been
observed. By flushing the D-cache, execution of binaries backed
by md(4) and/or NFS work reliably.
For Book-E (powerpc), execution over NFS exhibits SIGILL once in
a while as well, though cpu_flush_dcache() hasn't been implemented
yet.
Doing an explicit D-cache flush as part of the non-DMA based I/O
read operation eliminates the need to do it as part of the
I-cache coherency operation itself and as such avoids pessimizing
the DMA-based I/O read operations for which D-cache are already
flushed/invalidated. It also allows future optimizations whereby
the bcopy() followed by the D-cache flush can be integrated in a
single operation, which could be implemented using on-chips DMA
engines, by-passing the D-cache altogether.
register 0x52, not ctrl1. This appears to be a mistake in the bcm
reverse engineering page, and has been corrected there. Tracing
through the code, this is more in keeping with the "documented"
register. Sephe thinks it looks interesting and may be worth
fixing. :)
Submitted by: ddkprog at yahoo com
Reviewed by: Sepherosa Ziehau
- In bce_rx_intr(), use BUS_DMASYNC_POSTREAD instead of
BUS_DMASYNC_POSTWRITE, as we want to "read" from the
rx page chain pages.
- Document why we need to do PREWRITE after we have updated
the rx page chain pages.
- In bce_intr(), use BUS_DMASYNC_POSTREAD and
BUS_DMASYNC_PREREAD when before and after CPU "reading"
the status block.
- Adjust some nearby style mismatches/etc.
Pointed out by: yongari
Approved by: davidch (no objection) but bugs are mine :)
# Note: The driver doesn't support either these PHY types, so this is
# effectively a nop.
Submitted by: "ddk"
Obtained from: http://paradox.lissyara.su/bwi.diff
believe it was a BCM4319. However, it is the a/b/g variation of the
BCM4318. The chip itself is labelled BCM4318EKFBG, and the board is
BCM94318MKABG.
Paradox's patch includes the type of 802.11 wireless for each card,
but changes all the names (I don't think the latter is quite right).
Import that part of the patch, but keep the current set of BCM names
(with a minor tweak for the 4306 ones). I'll need to verify them via
some other means.
Obtained from: http://paradox.lissyara.su/bwi.diff (partially)
Apart from the 16 virtual terminals, Syscons allocates two device nodes
that should not really be TTYs, even though they are. One of them is
consolectl. In RELENG_7 and before, these device nodes are used in
single user mode. After I simplified input path, we only use this device
node to call ioctl() on (moused, Xorg, vidcontrol).
When you call ioctl() on consolectl, it will behave the same as being
called on the first window.
drops and re-grabs the softc mutex in the middle, resulting in kernel
trap 12. This may happen when a lot of traffic is being hammered on
one bge(4) interface while the system is shutting down.
Reported by: Alexander Sack <pisymbol gmail com>
PR: kern/134548
MFC After: 2 weeks
chipset-specific code to attach chipset-specific data.
- Use chipset-specific data in the acard and promise chipsets rather than
changing the ivars of ATA PCI devices. ivars are reserved for use by the
parent bus driver and are _not_ available for use by devices directly.
This fixes a panic during sysctl -a with certain Promise controllers with
ACPI enabled.
Reviewed by: mav
Tested by: Magnus Kling (kingfon @ gmail) (on 7)
MFC after: 3 days
NULL or change it. We initialize it before we set if_ioctl. It can
therefore never be NULL, and most other drivers don't bother with this
sanity check.
As an experiment, I changed snp(4) to use a mutex instead of an sx lock.
We can't enable this right now, because Syscons still picks up Giant.
It's nice to already have the framework there.
adapted to MPSAFE cam(4) to a isp(4) specific callout structure.
Thanks to Florian Smeets for providing access to a machine exhibiting
this problem for debugging.
Approved by: mjacob
MFC after: 3 days
sc_rixmap is an inverse map
NB: could eliminate the check for an invalid rate by filling in 0 for
invalid entries but the rate control modules use it to identify
bogus rates so leave it for now
previously always pointing to the default vnet context, to a
dynamically changing thread-local one. The currvnet context
should be set on entry to networking code via CURVNET_SET() macros,
and reverted to previous state via CURVNET_RESTORE(). Recursions
on curvnet are permitted, though strongly discuouraged.
This change should have no functional impact on nooptions VIMAGE
kernel builds, where CURVNET_* macros expand to whitespace.
The curthread->td_vnet (aka curvnet) variable's purpose is to be an
indicator of the vnet context in which the current network-related
operation takes place, in case we cannot deduce the current vnet
context from any other source, such as by looking at mbuf's
m->m_pkthdr.rcvif->if_vnet, sockets's so->so_vnet etc. Moreover, so
far curvnet has turned out to be an invaluable consistency checking
aid: it helps to catch cases when sockets, ifnets or any other
vnet-aware structures may have leaked from one vnet to another.
The exact placement of the CURVNET_SET() / CURVNET_RESTORE() macros
was a result of an empirical iterative process, whith an aim to
reduce recursions on CURVNET_SET() to a minimum, while still reducing
the scope of CURVNET_SET() to networking only operations - the
alternative would be calling CURVNET_SET() on each system call entry.
In general, curvnet has to be set in three typicall cases: when
processing socket-related requests from userspace or from within the
kernel; when processing inbound traffic flowing from device drivers
to upper layers of the networking stack, and when executing
timer-driven networking functions.
This change also introduces a DDB subcommand to show the list of all
vnet instances.
Approved by: julian (mentor)
Broadcom BCM43xx chipsets. This driver uses the v3 firmware that
needs to be fetched separately. A port will be committed to create
the bwi firmware module.
The driver matches the following chips: Broadcom BCM4301, BCM4307,
BCM4306, BCM4309, BCM4311, BCM4312, BCM4318, BCM4319
The driver works for 802.11b and 802.11g.
Limitations:
This doesn't support the 802.11a or 802.11n portion of radios.
Some BCM4306 and BCM4309 cards don't work with Channel 1, 2 or 3.
Documenation for this firmware is reverse engineered from
http://bcm.sipsolutions.net/
V4 of the firmware is needed for 11a or 11n support
http://bcm-v4.sipsolutions.net/
Firmware needs to be fetched from a third party, port to be committed
# I've tested this with a BCM4319 mini-pci and a BCM4318 CardBus card, and
# not connected it to the build until the firmware port is committed.
Obtained from: DragonFlyBSD, //depot/projects/vap
Reviewed by: sam@, thompsa@
leading to a bug, when C-state does not decrease on sleep shorter then
declared transition latency. Fixing this deprecates workaround for broken
C-states on some hardware.
By the way, change state selecting logic a bit. Instead of last sleep
time use short-time average of it. Global interrupts rate in system is a
quite random value, to corellate subsequent sleeps so directly.
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
- Generate fake channel interrupts even if channel busy with previous
request to let it finish. Without this, dumping requests were just queued
and never processed.
- Drop pre-dump requests queue on dumping. ATA code, working in dumping
(interruptless) mode, unable to handle long request queue. Actually, to get
coherent dump we anyway should do as few unrelated actions as possible.
Yukon from common multicast handling code. Yukon uses hash-based
multicast filtering(big endian form) but GENESIS uses perfect
multicast filtering as well as hash-based one(little endian form).
Due to the differences of multicast filtering there is no much
sense to have a common code.
o Remove sk_setmulti() and introduce sk_rxfilter_yukon(),
sk_rxfilter_yukon() that handles multicast filtering setup.
o Have sk_rxfilter_{yukon, genesis} handle promiscuous mode and
nuke sk_setpromisc(). This simplifies ioctl handler as well as
giving a chance to check validity of Rx control register of
Yukon.
o Don't reinitialize controller when IFF_ALLMULTI flags is changed.
o Nuke sk_gmchash(), it's not needed anymore.
o Always reconfigure Rx control register whenever a new multicast
filtering condition is changed. This fixes multicast filtering
setup on Yukon.
PR: kern/134051
- Probe supported sleep states from acpi_attach() just once and do not
call AcpiGetSleepTypeData() again. It is redundant because
AcpiEnterSleepStatePrep() does it any way.
- Treat UNKNOWN sleep state as NONE, i.e., "do nothing", and remove obscure
NONE state (ACPI_S_STATES_MAX + 1) to avoid confusions.
- Do not set unsupported sleep states as default button/switch events.
If the default sleep state is not supported, just set it as UNKNOWN/NONE.
- Do not allow sleep state change if the system is not fully up and running.
This should prevent entering S5 state multiple times, which causes strange
behaviours later.
- Make sleep states case-insensitive when they are used with sysctl(8).
For example,
sysctl hw.acpi.lid_switch_state=s1
sysctl hw.acpi.sleep_button_state=none
are now legal and equivalent to the uppercase ones.
Feature is controlled by hint.ata.X.pm_level tunable:
0 - PM disabled, old behaviour, default.
1 - device is allowed to initiate PM state change, host is passive.
2 - host initiates PARTIAL state transition every time port is idle.
3 - host initiates SLUMBER state transition every time port is idle.
PARTIAL state has up to 100us (50us for me) wakeup latency, but for my
ICH8M saves 0.5W of power per drive. SLUMBER state has up to 10ms (3.5ms
for me) wakeup latency, but saves 0.8W of power.
Modes 2 and 3 are implemented only for AHCI driver now.
Interface power management is incompatible with device presence detection
(host receives no signal from drive, so unable to monitor it), so later is
disabled when PM is used.
- Add some missing const.
- Move the size of the window spun by the registers to the softc
as neither using va_mem_size for this nor va_mem_base for the
start of the bus addresses is appropriate.
MFC after: 1 week
This change adds (possibly redundant) early check for invalid
state input parameter (including S0). Handling of S5 request
is reduced to simply calling shutdown_nice(). As a result
control flow of acpi_EnterSleepState is somewhat simplified
and resume/backout half of the function is not executed
for S5 (soft poweroff) request and invalid state requests.
Note: it seems that shutdown_nice may act as nop when initproc
is already initialized (to grab pid of 1), but init process is in
"pre-natal" state.
Tested by: Fabian Keil <fk@fabiankeil.de>
Reviewed by: njl, jkim
Approved by: rpaulo
controllers may be configured as legacy IDE mode by modifying subclass and
progif without actually changing PCI device IDs. Instead of complicating
code, we always force AHCI mode while probing. Also we restore AHCI mode
while resuming per ATI/AMD register programming/requirement guides.
- Fix SB700/800 "combined" mode. Unlike SB600, this PATA controller can
combine two SATA ports and emulate one PATA channel as primary or secondary
depending on BIOS configuration. When the combined mode is disabled, this
channel disappears and it works just like SB600 PATA controller, however.
- Add more PCI device IDs for SB700/800 and adjust device descriptions.
SB800 shares the same PCI device IDs and added two more SATA IDs.
this driver to compile and limp along with the new layer. These changes
do not deal with proper locking around access to the HW. This is only
a starting point. I have not tested modem control but tip seems to work
okay and I can send and receive characters which I needed for one of my
-current boxes. I have not tied this driver back up to the build since
I don't want people to think it is ready for prime time. If anyone
else has some cycles to work on this feel free to!
Also add support for a 16 port PCI interface I have at work.
Glanced at by: ed
- Update mxge to use if_transmit(), and the new buf_ring
interfaces, so as to enable multiple transmit queues.
Use of if_transmit() is conditional on IFNET_BUF_RING,
and is enabled by default (as in if_em).
- Record a flow id on receive if receive hashing is active.
I currently only record the rx ring id (0..8) rather than
the 32-bit topelitz hash result, as doing the latter would
require shifting the driver to use a larger rx return ring.
Sponsored by: Myricom, Inc.
(1) Don't manually configure if_output(), ether_ifattach() will do that
for us as part of link-layer setup.
(2) Call if_detach() before stopping nve in order to prevent calls into
the device driver after the driver has started shutting down.
Reviewed by: jhb
MFC after: 2 weeks
Change the roothub exec functions to take the usb request and data pointers
directly rather than placing them on the parent bus struct.
Submitted by: Hans Petter Selasky
Fix a bug in the USB power daemon code where connection of multiple HUBs in
series would result in incorrect device suspend.
Reported by: Nicolas xxx@wanadoo.fr
Submitted by: Hans Petter Selasky
Use direct reference to parent high-speed HUB instead of indirect, due to
pointer clearing race at detach of parent USB HUB.
Reported by: kientzle
Submitted by: Hans Petter Selasky
PR: usb/133545
respectivly. This will allow one to have a kernel with both devices
present and use it for multiple boards with different types of RTC
sitting on a bus.
Discussed with: imp
number of queued packets in watchdog timeout handler. If there are
no queued packets just print a informational message and return
without resetting controller. Also fix to invoke correct Tx
completion handler as 3C905B needs different handler.
Previously it used to clear the flag only when the transmit queue
is empty which may slow down Tx performance.
While I'm here check whether driver is running and whether we can
queue more packets in if_start handler. This fixes occasional
watchdog timeouts.
Reported by: xer < xernet <> hotmail dot it >
Tested by: xer < xernet <> hotmail dot it >
checksum offload frames. Software workaround used for broken
controllers(RTL8169, RTL8168, RTL8168B) seem to cause watchdog
timeouts on RTL8139C+.
Introduce a new flag RL_FLAG_AUTOPAD to mark automatic padding
feature of controller and set it for RTL8139C+ and controllers that
use new descriptor format. This fixes watchdog timeouts seen on
RTL8139C+.
Reported by: Dimitri Rodis < DimitriR <> integritasystems dot com >
Tested by: Dimitri Rodis < DimitriR <> integritasystems dot com >
registers.
- Cleanup PCI-X capability printf to not leave a dangling "supports" for
some PCI-X bridges.
- Display additional PCI express details including the negotiated and max
link width and the actual and maximum supported max payload.
MFC after: 1 month
when polled mode is enabled. This should help with duplicated/missing
characters problem at mountroot, geli, etc. prompts on multi CPU systems
while kbdmux(4) is enabled.
Tested by: Tobias Grosser <grosser -at- fim -dot- uni-passau -dot- de>
Tested by: Fabian Keil <freebsd-listen -at- fabiankeil -dot- de>
MFC after: 3 days
network load.
1. Leave the RX interrupt routine if there is no mbuf available.
2. Properly initialize and track tx_desc_used_count counter so as not to
leak mbuf while traversing used descriptors.
Obtained from: Semihalf
- Remove redundant softc members for RIDs.
- Change some softc members to be unsigned where more appropriate.
- Add some missing const.
- Remove support for mmap(2)'ing VGA I/O as it was broken [1] and
not required by X.Org anyway.
- Fix some confusion between bus, physical and virtual addresses
which mostly consisted in using members of struct video_adapter
inappropriately but wasn't fatal except for the regular framebuffer
mmap(2)'ing.
- Remove redundant bzero(9)'ing of the softc.
- Don't map the framebuffer twice in case the firmware has already
mapped it as besides wasting resources this isn't possible with
all MMUs. This is a bit tricky as a) just because the firmware
provides a property with a virtual address doesn't mean it's
actually mapped (but typically is when the framebuffer is the
console) and b) the firmware doesn't necessarily map the it with
the same byteorder as we do. This make machfb(4) work on machines
with cheetah-class MMUs (including X.Org).
Reported by: Michael Plass [1]
MFC after: 3 days
addresses to BARs into new pci_read_bar() and pci_write_bar() routines.
pci_add_map(), pci_alloc_map(), and pci_delete_resource() now use these
routines to work with BARs.
- Just pass the device_t for the new PCI device to various routines instead
of passing the device, bus, slot, and function.
Reviewed by: imp
Remote host can advertise smaller MSS than that of sender so upper
stack might have adjusted the MSS which in turn generates IP
packets that are less size than that of interface MTU.
Reported by: Bjoern Koenig ( bkoenig <> alpha-tierchen dot de )
Tested by: Bjoern Koenig ( bkoenig <> alpha-tierchen dot de )
MFC after: 3 days
TCPSTAT_INC(), rather than directly manipulating the fields across the
kernel. This will make it easier to change the implementation of
these statistics, such as using per-CPU versions of the data structures.
MFC after: 3 days
1) Flag it and only access that command on the 3c1
2) The TX PLL appears to power down when not in use, so we have to power
it back up when we've been idle. Do this at the start of ifstart.
Otherwise we fall off the net.
have other media to test against, I've left that media reporting
unchanged.
o Enable the TX_PLL when we enable TX. This is harmless on most
cards, but required to get the 3c1 CF card working. Power savings
could be had by managing this better, but for now it gets my card
working.
We typically wire translation to devices with TLB1 entries and
pmap_kextract() does not know about those and returns 0. This
causes false positives (read: all serial ports suddenly become
the console).
Do not use Giant for kbdmux(4) locking. This is wrong and apparently
causing more problems than it solves. This will re-open the issue
where interrupt handlers may race with kbdmux(4) in polling mode.
Typical symptoms include (but not limited to) duplicated and/or
missing characters when low level console functions (such as gets)
are used while interrupts are enabled (for example geli password
prompt, mountroot prompt etc.)
MFC after: 3 days
(framing, parity, etc), but does not indicate characters
being received. Since no chracters have been received,
ignore the line errors.
PR: 131006
MFC after: 3 days
instead of just register one for the first adapter. Without doing this
there would be some data loss upon shutdown because data could be ignored
when flushing to disk.
MFC after: 3 days
- override_kernel_driver() has been removed since this is an
in-tree version of driver.
- __DATE__ and __TIME__ removed from version string to make
binary update builders happy.
- Utilize pause(9) for __FreeBSDversion >= 700033 (redo 167086).
- Utilize kproc_suspend_check() for __FreeBSDversion >= 800002.
(redo 172836).
- Don't read past end of pVDevice (redo 143787).
- Make sure that controller and channel are initialized (redo 169823).
- Don't include cam/cam_xpt_periph.h (redo 158177).
MFC After: 3 days
and update comments about original patches doing this and it not
working. It works for both the DL10019 and DL10022 based cards that I
have. It really helps the DL10019 cards, since they were using 8k
instead of the normal 16k that regular NE-2000 cards help.
# Note to self: need to provide a common routine to setup memory
# parameters.
