for the given channel is available.
It isn't used yet; ar5416GetWirelessModes() needs to be taught
about this rather than assuming HT20/HT40 is available.
This seems to make the AR9160 behave better during heavy scanning,
where before it'd hang and require a hard reset to recover.
Obtained From: Linux ath9k, Atheros
modifying AR_DIAG_SW.
There's a hardware workaround which sets disabling some errors
early at startup and clears said bits before the PCU begins
receiving - it does this to avoid RX descriptor status errors.
It's possible these bits aren't being completely properly twiddled
in all instances; but in particular if the diag_reg HAL variable
is set it won't be setting these bits correctly. I'll review this
at some point.
* Disable multicast search on mac address and key id - the driver
doesn't use it at the moment and thus adhoc may be broken for
merlin and later.
* Change this to be for Merlin 1.0 (which from what I understand
wasn't ever publicly released) to be more correct.
Apparently all three RX chains need to be enabled before initial calibration
is done, even if only two are configured.
Reorder the alt chain swap bit to match what the Atheros HAL is doing.
Obtained From: ath9k, Atheros
starting from base C types (int, long, etc).
That is also reflected when building atomic operations, as the
size-bounded types are built from the base C types.
However, powerpc does the inverse thing, leading to a serie of nasty
bugs.
Cleanup the atomic implementation by defining as base the base C type
version and depending on them, appropriately.
Tested by: jceel
* Shuffle some of the capability numbers around to match the
Atheros HAL capability IDs, just for consistency.
* Add some new capabilities to FreeBSD from the Atheros
HAL which will be be shortly used when new chipsets are added
(HAL SGI-20 support is for Kiwi/AR9287 support); for
TX aggregation (MBSSID aggregate support, WDS aggregation
support); CST/GTT support for carrier sense/TX timeout.
channel when the channel is HT/40.
The new ANI code (primarily for the AR9300/AR9400) in ath9k sets this
register but the ANI code for the previous 11n chips didn't set this.
Unlike ath9k, only set this for HT/40 channels.
Obtained From: ath9k
These describe FCC/Japan channel and DFS behaviour.
The AR9285 and later chips don't set these bits in the eeprom, the correct
behaviour is to just assume all five bits are enabled.
An optical disk may not have a TOC (e.g. for blank media) and userland
software may legitimately try to use CDIOREADTOCHEADER to find out about
the TOC.
Silence from: scsi@
MFC after: 10 days
specific.
The Atheros HAL and FreeBSD HAL share the same capabilities up
until HAL_CAP_11D, where things begin to diverge.
I'll look at tidying these up soon.
Obtained from: Atheros
* Add Howl (ar9130) to the list of chips that have DFS/BB/MAC hangs
* Don't treat unknown BB hangs as fatal; ath9k/Atheros HAL don't
treat it as such.
* Add HAL_DEBUG_DFS to the debug fields in ath_hal/ah_debug.h
The BB hang check simply loops over an observation register checking
for a stuck state engine, but it can happen under high traffic
conditions. Ath9k and the Atheros HAL simply log a debug message and
continue.
Private to FreeBSD:
* Add HAL_DEBUG_HANG to the debug fields
* Change the hang debugging to HAL_DEBUG_HANG rather than HAL_DEBUG_DFS
like in the Atheros HAL.
Obtained from: Atheros
For now, these are equivalent macros. AR_SREV_OWL{X}_OR_LATER
will later change to exclude Howl (AR9130) in line with what
the Atheros HAL does.
This should not functionally change anything.
Obtained from: Atheros
A quick story, which is partially documented in the commit.
The silicon revision in Linux ath9k and the Atheros HAL use an
AR_SREV_REVISION mask of 0x07.
FreeBSD's HAL uses the AR5212 AR_SREV_REVISION mask of 0x0F.
Thus the OWL silicon revisions were coming through as 0xA, 0xB,
0xC, rather than 0x0, 0x1 and 0x2.
My ath9k-sourced AR_SREV_OWL_<X> macros were thus using the wrong
silicon revision values and wouldn't correctly match.
This commit does a few things:
* Change the AR_SREV_OWL_<x> macros to use the AR_SREV_REVISION_OWL_*
values, not AR_XSREV_REVISION_OWL macros;
* Disable AR_XSREV_REVISION_OWL_* values;
* Modify the IS_5416 to properly check the MAC is OWL, rather than
potentially matching on non-OWL revisions (which shouldn't happen
unless there's a silicon revision of higher than 0x9 in a later
chip..)
* Add a couple more macros from the Atheros HAL for compatibility.
The main difference now is that the Atheros HAL defines
AR_SREV_OWL_{20,22}_OR_LATER subtly differently - it fails on all HOWL
silicon. The AR_SREV_5416_*_OR_LATER macros match on the relevant OWL
version -and- all HOWL versions, along with subsequent versions.
A subsequent commit is going to migrate the uses of AR_SREV_OWL_X_OR_LATER
to AR_SREV_5416_X_OR_LATER to match what's going on in the Atheros HAL.
There's only two uses of AR_SREV_OWL_X_OR_LATER which currently don't
apply to FreeBSD but it may do in the future.
Yes, it's all confusing!
tick driving logic to xl_tick(). Now xl_tick() handles MII tick as
well as periodic updating of statistics.
This change removes a hack used in interrupt handler where it
wanted to update statistics without driving MII tick.
picking the next available one. This may explain why xl(4) sees TX
underrun error with no queued frame. I hope this addresses a long
standing xl(4) watchdog timeout issue as well.
Obtained from: OpenBSD
RX descriptor ring. Previously it returned the number of frames
that were successfully passed to upper stack which in turn means it
ignored frames that were discarded due to errors. The number of
processed frames in RX descriptor ring is used to detect whether
driver is out of sync with controller's current descriptor pointer.
Returning number of processed frames reduces unnecessary (probably
wrong) re-synchronization.
While here, remove unnecessary local variable initialization.
handler for 3C90x and 3C90xB/C respectively. This simplifies ioctl
handler as well as enhancing readability.
While I'm here don't reprogram multicast filter when driver is not
running.
Transmission error in tun(4) is queueing error(i.e. ENOBUFS) and it
has nothing to do with collision.
Reported by: Zeus V Panchenko (zeus <> ibs dot dn dot ua)
new NFS client. It will then be reduced to whatever the
server says it can support. There might be an argument
that this could be one block larger, but since NFS is
a byte granular system, I chose not to do that.
Suggested by: Matt Dillon
Tested by: Daniel Braniss (earlier version)
MFC after: 2 weeks
This also introduces a new detection path for family 10h and newer
pre-bulldozer cpus, pre-10h hardware should not be affected.
Tested by: Gary Jennejohn <gljennjohn@googlemail.com>
(with pre-10h hardware)
MFC after: 2 weeks
versions instead. They were never needed as bus_generic_intr() and
bus_teardown_intr() had been changed to pass the original child device up
in 42734, but the ISA bus was not converted to new-bus until 45720.
or f_ffree fields of "struct statfs" are negative, since the
values that go on the wire are unsigned and will appear to be
very large positive values otherwise. This makes the handling
of a negative f_bavail compatible with the old/regular NFS server.
MFC after: 2 weeks
This fixes heavy interrupt storm and resulting system freeze when using
LAPIC timer in one-shot mode under Xen HVM. There, unlike real hardware,
programming timer with zero period almost immediately causes interrupt.
this there is a rare return path that bogusly appears
to fail when it should not. Also white space correction.
Thanks to Arnaud Lacombe for noticing the problem.
cpuset_t objects.
That is going to offer the underlying support for a simple bump of
MAXCPU and then support for number of cpus > 32 (as it is today).
Right now, cpumask_t is an int, 32 bits on all our supported architecture.
cpumask_t on the other side is implemented as an array of longs, and
easilly extendible by definition.
The architectures touched by this commit are the following:
- amd64
- i386
- pc98
- arm
- ia64
- XEN
while the others are still missing.
Userland is believed to be fully converted with the changes contained
here.
Some technical notes:
- This commit may be considered an ABI nop for all the architectures
different from amd64 and ia64 (and sparc64 in the future)
- per-cpu members, which are now converted to cpuset_t, needs to be
accessed avoiding migration, because the size of cpuset_t should be
considered unknown
- size of cpuset_t objects is different from kernel and userland (this is
primirally done in order to leave some more space in userland to cope
with KBI extensions). If you need to access kernel cpuset_t from the
userland please refer to example in this patch on how to do that
correctly (kgdb may be a good source, for example).
- Support for other architectures is going to be added soon
- Only MAXCPU for amd64 is bumped now
The patch has been tested by sbruno and Nicholas Esborn on opteron
4 x 12 pack CPUs. More testing on big SMP is expected to came soon.
pluknet tested the patch with his 8-ways on both amd64 and i386.
Tested by: pluknet, sbruno, gianni, Nicholas Esborn
Reviewed by: jeff, jhb, sbruno
Quoting the ath9k commit message:
At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.
This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.
Reference: https://patchwork.kernel.org/patch/753862/
Obtained from: Linux ath9k
The checks should function as follows:
* AR_SREV_<silicon> : check macVersion matches that version id
* AR_SREV_<silicon>_<revision> : check macVersion and macRevision match
the version / revision respectively
* AR_SREV_<silicon>_<revision>_OR_LATER: check that
+ if the chip silicon version == macVersion, enforce revision >= macRevision
+ if the chip silicon version > macVersion, allow it.
For example, AR_SREV_MERLIN() only matches AR9280 (any revision),
AR_SREV_MERLIN_10() would only match AR9280 version 1.0, but
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 version >= 2.0 _AND_
any subsequent MAC (So AR9285, AR9287, etc.)
The specific fixes which may impact users:
* if there is Merlin hardware > revision 2.0, it'll now be correctly
matched by AR_SREV_MERLIN_20_OR_LATER() - the older code simply
would match on either Merlin 2.0 or a subsequent MAC (AR9285, AR9287, etc.)
* Kite version 1.1/1.2 should now correctly match. As these macros
are used in the AR9285 reset/attach path, and it's assumed that the
hardware is kite anyway, the behaviour shouldn't change. It'll only
change if these macros are used in other codepaths shared with
older silicon.
Obtained from: Linux ath9k, Atheros
Reference code that shows how to get a packet's timestamp out of
cxgbe(4). Disabled by default because we don't have a standard way
today to pass this information up the stack.
The timestamp is 60 bits wide and each increment represents 1 tick of
the T4's core clock. As an example, the timestamp granularity is ~4.4ns
for this card:
# sysctl dev.t4nex.0.core_clock
dev.t4nex.0.core_clock: 228125
MFC after: 1 week
- Enable 5-tuple and every-packet lookup.
- Setup the default filter mode to allow filtering/steering based on IP
protocol, ingress port, inner VLAN ID, IP frag, FCoE, and MPS match
type; all combined together. You can also filter based on MAC index,
Ethernet type, IP TOS/IPv6 Traffic Class, and outer VLAN ID but you'll
have to modify the default filter mode and exclude some of the
match-fields in it.
IPv4 and IPv6 SIP/DIP/SPORT/DPORT are always available in all filter
rules.
- Add driver ioctls to get/set the global filter mode.
- Add driver ioctls to program and delete hardware filters. A couple of
the "switch" actions that rewrite Ethernet and VLAN information and
switch the packet out of another port may not work as the L2 code is not
yet in place. Everything else, including all "drop" and "pass" rules
with RSS or absolute qid, should work.
Obtained from: Chelsio Communications
that are now in "struct statfs" for NFSv3 and NFSv4. Since
the ffiles value is uint64_t on the wire, I clip the value
to INT64_MAX to avoid setting f_ffree negative.
Tested by: kib
MFC after: 2 weeks
values of error numbers in sys/errno.h will be the same
as the ones specified by the NFS RFCs and that the code
needs to be fixed if error numbers are changed in sys/errno.h.
Suggested by: Peter Jeremy
MFC after: 2 weeks
have similar hardware features of BCM5718 family except the number
of receive return ring is 4. The BCM57765 family is known to
support IEEE 802.3az EEE(Energy Efficient Ethernet) but this change
does not include EEE support code. I hope EEE is implemented in
near future.
This change will support BCM57761, BCM57765, BCM57781, BCM57785,
BCM57791 and BCM57795. All hardware offloading features are
supported and suspend/resume also should work.
Many thanks to Broadcom for continuing support of FreeBSD.
Tested by: Paul Thornton (prt <> prt dot org)
HW donated by: Broadcom
checking at open time. It may improve performance for read-only
NFS mounts. Use deliberately.
MFC after: 1 week
Reviewed by: rmacklem, jhb (earlier version)
native devices which support the v4l2 API from processes running within
the linuxulator, e.g. skype or flash can access the multimedia/pwcbsd
or multimedia/webcamd supplied drivers.
Submitted by: nox
MFC after: 1 month
handling.
The current sequence number code does a few things incorrectly:
* It didn't try eliminating duplications from HT nodes. I guess it's assumed
that out of order / retransmission handling would be handled by the AMPDU RX
routines. If a HT node isn't doing AMPDU RX, then retransmissions need to
be eliminated. Since most of my debugging is based on this (as AMPDU TX
software packet aggregation isn't yet handled), handle this corner case.
* When a sequence number of 4095 was received, any subsequent sequence number
is going to be (by definition) less than 4095. So if the following sequence
number (0) doesn't initially occur and the retransmit is received, it's
incorrectly eliminated by the IEEE80211_FC1_RETRY && SEQ_LEQ() check.
Try to handle this better.
This almost completely eliminates out of order TCP statistics showing up during
iperf testing for the 11a, 11g and non-aggregate 11n AMPDU RX case. The only
other packet loss conditions leading to this are due to baseband resets or
heavy interference.
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
driver would verify that requests for child devices were confined to any
existing I/O windows, but the driver relied on the firmware to initialize
the windows and would never grow the windows for new requests. Now the
driver actively manages the I/O windows.
This is implemented by allocating a bus resource for each I/O window from
the parent PCI bus and suballocating that resource to child devices. The
suballocations are managed by creating an rman for each I/O window. The
suballocated resources are mapped by passing the bus_activate_resource()
call up to the parent PCI bus. Windows are grown when needed by using
bus_adjust_resource() to adjust the resource allocated from the parent PCI
bus. If the adjust request succeeds, the window is adjusted and the
suballocation request for the child device is retried.
When growing a window, the rman_first_free_region() and
rman_last_free_region() routines are used to determine if the front or
end of the existing I/O window is free. From using that, the smallest
ranges that need to be added to either the front or back of the window
are computed. The driver will first try to grow the window in whichever
direction requires the smallest growth first followed by the other
direction if that fails.
Subtractive bridges will first attempt to satisfy requests for child
resources from I/O windows (including attempts to grow the windows). If
that fails, the request is passed up to the parent PCI bus directly
however.
The PCI-PCI bridge driver will try to use firmware-assigned ranges for
child BARs first and only allocate a "fresh" range if that specific range
cannot be accommodated in the I/O window. This allows systems where the
firmware assigns resources during boot but later wipes the I/O windows
(some ACPI BIOSen are known to do this) to "rediscover" the original I/O
window ranges.
The ACPI Host-PCI bridge driver has been adjusted to correctly honor
hw.acpi.host_mem_start and the I/O port equivalent when a PCI-PCI bridge
makes a wildcard request for an I/O window range.
The new PCI-PCI bridge driver is only enabled if the NEW_PCIB kernel option
is enabled. This is a transition aide to allow platforms that do not
yet support bus_activate_resource() and bus_adjust_resource() in their
Host-PCI bridge drivers (and possibly other drivers as needed) to use the
old driver for now. Once all platforms support the new driver, the
kernel option and old driver will be removed.
PR: kern/143874 kern/149306
Tested by: mav
Rationale:
- unlike current behavior this seems to be compliant with OSS
specification:
http://manuals.opensound.com/developer/SNDCTL_DSP_GETIPTR.html
- this seems to meet expectations of some OSS programs compiled for or
ported from Linux, e.g. ALSA OSS plugin
- this doesn't seem to break any programs as far as current testing
shows
Tested by: nox, hselasky
MFC after: 4 days
structure, which acts as a proxy between them. This makes jail rules
persistent, i.e. they can be added before jail gets created, and they
don't disappear when the jail gets destroyed.
and our users complained when broken.
Similarly add LINT-NOINET, and for at least documentation purposes add
LINT-NOIP (which compiles out INET and INET6 and couple of NIC drivers).
Tested by: make universe (if you broke it since you fix it)
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 2 weeks
buffer fills up causing the remote sender to enter into persist mode, but
there is still room available in the receive buffer when a window probe
arrives (either due to window scaling, or due to the local application
very slowing draining data from the receive buffer), then the single byte
of data in the window probe is accepted. However, this can cause rcv_nxt
to be greater than rcv_adv. This condition will only last until the next
ACK packet is pushed out via tcp_output(), and since the previous ACK
advertised a zero window, the ACK should be pushed out while the TCP
pcb is write-locked.
During the window while rcv_nxt is greather than rcv_adv, a few places
would compute the remaining receive window via rcv_adv - rcv_nxt.
However, this value was then (uint32_t)-1. On a 64 bit machine this
could expand to a positive 2^32 - 1 when cast to a long. In particular,
when calculating the receive window in tcp_output(), the result would be
that the receive window was computed as 2^32 - 1 resulting in advertising
a far larger window to the remote peer than actually existed.
Fix various places that compute the remaining receive window to either
assert that it is not negative (i.e. rcv_nxt <= rcv_adv), or treat the
window as full if rcv_nxt is greather than rcv_adv.
Reviewed by: bz
MFC after: 1 month
of the 61 bits available within the region for virtual addressing. Since
there's no good way for us to map out the gap in the virtual address space,
limit KVA to the architectural minimum implemented address bits. This still
gives us 1 petabyte of KVA, so no worries.
developers committing new code with broken include directories.
Fix a few whitespace issues.
Improve a couple of comments.
-W is now deprecated and is referred to as -Wextra (see gcc(1)).
Submitted by: arundel
of endian-ness issues with the AR724x.
From Luiz:
* Fix the bus space tag used so endian-ness is correctly handled;
* Only do the workaround for the AR7240; AR7241/AR7242 (PB92)
don't require this
From me:
* Add a read flush from openwrt
Submitted by: Luiz Otavio O Souza
kern.sched.ipiwakeup.onecpu
kern.sched.ipiwakeup.htt2
Because they are absolutely obsolete. Probabilly the whole wakeup
forward mechanism should be revisited for a better fitting in modern
hw.
- As map2 variable is no longer used rename map3 to map2
- Fix a string by making more informative the msg and removing the
arguments passing
Approved by: julian
function on the possibility of a thread to not preempt.
As this function is very tied to x86 (interrupts disabled checkings)
it is not intended to be used in MI code.
use the PBVM. This eliminates the implied hardcoding of the
physical address at which the kernel needs to be loaded. Using the
PBVM makes it possible to load the kernel irrespective of the
physical memory organization and allows us to replicate kernel text
on NUMA machines.
While here, reduce the direct-mapped page size to the kernel's
page size so that we can support memory attributes better.
kernel configurations to apply WITH_* WITHOUT_* knobs we use for
module building as well to restrict or control opt_*.h flags.
Reviewed by: imp, +
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 2 weeks
to get the files for an IPv6 only kernel as well, remove extra inet6
option where not needed.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
This is reported to work on the AR7240 based Ubiquiti Rocket M5
but I haven't tested it on that hardware. I also don't yet have
it fully working on the AR7242 based development board here;
probe/attach functions but the register space resource looks like
the endian-ness is wrong (0x10000000 instead of 0x00001000).o
Further digging will be required.
Submitted by: Luiz Otavio O Souza
Add some comments at #endifs given more nestedness. To make the compiler
happy, some default initializations were added in accordance with the style
on the files.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
Some bugs where fixed while doing this:
* ASCONF-ACK messages might use wrong port number when using
IPv6.
* Checking for additional addresses takes the correct address
into account and also does not do more comparisons than
necessary.
This patch is based on one received from bz@ who was
sponsored by The FreeBSD Foundation and iXsystems.
MFC after: 1 week
as well compiling out most functions adding or extending #ifdef INET
coverage.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
wrapper around rman_adjust_resource(). Include a generic implementation,
bus_generic_adjust_resource() which passes the request up to the parent
bus. There is currently no default implementation. A
bus_adjust_resource() wrapper is provided for use in drivers.
sectors with all-zeroes.
The zeroes come from a static buffer; null(4) uses a dynamic buffer for
the same purpose (for /dev/zero). It might be a good idea to have a
static, shared, read-only all-zeroes page somewhere in the kernel that
md(4), null(4) and any other code that needs zeroes could use.
Reviewed by: kib
MFC after: 3 weeks
Specifically, these changes allow a resource to back a relocatable and
resizable resource such as the I/O window decoders in PCI-PCI bridges.
- rman_adjust_resource() can adjust the start and end address of an
existing resource. It only succeeds if the newly requested address
space is already free. It also supports shrinking a resource in
which case the freed space will be marked unallocated in the rman.
- rman_first_free_region() and rman_last_free_region() return the
start and end addresses for the first or last unallocated region in
an rman, respectively. This can be used to determine by how much
the resource backing an rman must be adjusted to accomodate an
allocation request that does not fit into the existing rman.
While here, document the rm_start and rm_end fields in struct rman,
rman_is_region_manager(), the bound argument to
rman_reserve_resource_bound(), and rman_init_from_resource().
constraints on the rman and reject attempts to manage a region that is out
of range.
- Fix various places that set rm_end incorrectly (to ~0 or ~0u instead of
~0ul).
- To preserve existing behavior, change rman_init() to set rm_start and
rm_end to allow managing the full range (0 to ~0ul) if they are not set by
the caller when rman_init() is called.
VMware products virtualize TSC and it run at fixed frequency in so-called
"apparent time". Although virtualized i8254 also runs in apparent time, TSC
calibration always gives slightly off frequency because of the complicated
timer emulation and lost-tick correction mechanism.
persist state and the retransmit timer. However, the code that implements
"bad retransmit recovery" only checks t_rxtshift to see if an ACK has been
received in during the first retransmit timeout window. As a result, if
ticks has wrapped over to a negative value and a socket is in the persist
state, it can incorrectly treat an ACK from the remote peer as a
"bad retransmit recovery" and restore saved values such as snd_ssthresh and
snd_cwnd. However, if the socket has never had a retransmit timeout, then
these saved values will be zero, so snd_ssthresh and snd_cwnd will be set
to 0.
If the socket is in fast recovery (this can be caused by excessive
duplicate ACKs such as those fixed by 220794), then each ACK that arrives
triggers either NewReno or SACK partial ACK handling which clamps snd_cwnd
to be no larger than snd_ssthresh. In effect, the socket's send window
is permamently stuck at 0 even though the remote peer is advertising a
much larger window and pending data is only sent via TCP window probes
(so one byte every few seconds).
Fix this by adding a new TCP pcb flag (TF_PREVVALID) that indicates that
the various snd_*_prev fields in the pcb are valid and only perform
"bad retransmit recovery" if this flag is set in the pcb. The flag is set
on the first retransmit timeout that occurs and is cleared on subsequent
retransmit timeouts or when entering the persist state.
Reviewed by: bz
MFC after: 2 weeks
in mnt_optnew. This is needed so that the old mount(2) syscall
works and that is needed so that amd(8) works. The code was
basically just cribbed from sys/nfsclient/nfs_vfsops.c with minor
changes. This patch is mainly to fix the new NFS client so that
amd(8) works with it. Thanks go to Craig Rodrigues for helping with
this.
Tested by: Craig Rodrigues (for amd)
MFC after: 2 weeks
For these devices, the number of supported ports is read from a register
in BAR 0.
PR: kern/134878
Submitted by: David Wood david of wood2 org uk
MFC after: 1 week
boot2 calls back into boot1 to perform disk reads. The ZFS MBR boot blocks
do not have the same space constraints, so remove this hack for ZFS.
While here, remove commented out code to support C/H/S addressing from
zfsldr. The ZFS and GPT bootstraps always just use EDD LBA addressing.
MFC after: 2 weeks
disk dumping.
With the option SW_WATCHDOG on, these operations are doomed to let
watchdog fire, fi they take too long.
I implemented the stubs this way because I really want wdog_kern_*
KPI to not be dependant by SW_WATCHDOG being on (and really, the option
only enables watchdog activation in hardclock) and also avoid to
call them when not necessary (avoiding not-volountary watchdog
activations).
Sponsored by: Sandvine Incorporated
Discussed with: emaste, des
MFC after: 2 weeks
- 77115: Implement support for O_DIRECT.
- 98425: Fix a performance issue introduced in 70131 that was causing
reads before writes even when writing full blocks.
- 98658: Rename the BALLOC flags from B_* to BA_* to avoid confusion with
the struct buf B_ flags.
- 100344: Merge the BA_ and IO_ flags so so that they may both be used in
the same flags word. This merger is possible by assigning the IO_ flags
to the low sixteen bits and the BA_ flags the high sixteen bits.
- 105422: Fix a file-rewrite performance case.
- 129545: Implement IO_INVAL in VOP_WRITE() by marking the buffer as
"no cache".
- Readd the DOINGASYNC() macro and use it to control asynchronous writes.
Change i-node updates to honor DOINGASYNC() instead of always being
synchronous.
- Use a PRIV_VFS_RETAINSUGID check instead of checking cr_uid against 0
directly when deciding whether or not to clear suid and sgid bits.
Submitted by: Pedro F. Giffuni giffunip at yahoo
* enable 11n
* add ath_ahb so the AHB<->ath glue is linked in
* disable descriptor order swapping, it isn't needed here
* disable interrupt mitigation, it isn't supported here
The AR9130 is an AR9160/AR5416 family WMAC which is glued directly
to the AR913x SoC peripheral bus (APB) rather than via a PCI/PCIe
bridge.
The specifics:
* A new build option is required to use the AR9130 - AH_SUPPORT_AR9130.
This is needed due to the different location the RTC registers live
with this chip; hopefully this will be undone in the future.
This does currently mean that enabling this option will break non-AR9130
builds, so don't enable it unless you're specifically building an image
for the AR913x SoC.
* Add the new probe, attach, EEPROM and PLL methods specific to Howl.
* Add a work-around to ah_eeprom_v14.c which disables some of the checks
for endian-ness and magic in the EEPROM image if an eepromdata block
is provided. This'll be fixed at a later stage by porting the ath9k
probe code and making sure it doesn't break in other setups (which
my previous attempt at this did.)
* Sprinkle Howl modifications throughput the interrupt path - it doesn't
implement the SYNC interrupt registers, so ignore those.
* Sprinkle Howl chip powerup/down throughout the reset path; the RTC methods
were
* Sprinkle some other Howl workarounds in the reset path.
* Hard-code an alternative setup for the AR_CFG register for Howl, that
sets up things suitable for Big-Endian MIPS (which is the only platform
this chip is glued to.)
This has been tested on the AR913x based TP-Link WR-1043nd mode, in
legacy, HT/20 and HT/40 modes.
Caveats:
* 2ghz has only been tested. I've not seen any 5ghz radios glued to this
chipset so I can't test it.
* AR5416_INTERRUPT_MITIGATION is not supported on the AR9130. At least,
it isn't implemented in ath9k. Please don't enable this.
* This hasn't been tested in MBSS mode or in RX/TX block-aggregation mode.
allocated, not the maximum number of messages the device supports. The
spec only requires the former, and I believe I implemented the latter due
to misunderstanding an e-mail. In particular, this fixes an issue where
having several devices that all support 16 messages can run out of
IDT vectors on x86 even though the driver only uses a single message.
Submitted by: Bret Ketchum bcketchum of gmail
MFC after: 1 week
Expose ip_icmp.c to INET6 as well and only export badport_bandlim()
along with the two sysctls in the non-INET case.
The bandlim types work for all cases I reviewed in IPv6 as well and
the sysctls are available as we export net.inet.* from in_proto.c.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
Move ip_defttl to raw_ip.c where it is actually used. In an IPv6
only world we do not want to compile ip_input.c in for that and
it is a shared default with INET6.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
adding appropriate #ifdefs. For module builds the framework needs
adjustments for at least carp.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
Unfold the IPSEC_COMMON_INPUT_CB() macro in xform_{ah,esp,ipcomp}.c
to not need three different versions depending on INET, INET6 or both.
Mark two places preparing for not yet supported functionality with IPv6.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
non-interruptible NFS mounts, where a kernel thread will seem
to be stuck sleeping on "rpccon". The msleep() in clnt_vc_create()
that was waiting to a TCP connect to complete would return ERESTART,
since PCATCH was specified. Then the tsleep() in clnt_reconnect_call()
would sleep for 1 second and then try again and again and...
The patch changes the msleep() in clnt_vc_create() so it only sets
the PCATCH flag for interruptible cases.
Tested by: pho
Reviewed by: jhb
MFC after: 2 weeks
NFS client (which I guess is no longer experimental). The fstype "newnfs"
is now "nfs" and the regular/old NFS client is now fstype "oldnfs".
Although mounts via fstype "nfs" will usually work without userland
changes, an updated mount_nfs(8) binary is needed for kernels built with
"options NFSCL" but not "options NFSCLIENT". Updated mount_nfs(8) and
mount(8) binaries are needed to do mounts for fstype "oldnfs".
The GENERIC kernel configs have been changed to use options
NFSCL and NFSD (the new client and server) instead of NFSCLIENT and NFSSERVER.
For kernels being used on diskless NFS root systems, "options NFSCL"
must be in the kernel config.
Discussed on freebsd-fs@.
the watchdog, via the watchdog(9) interface.
For that, the WD_LASTVAL bitwise operation is used. It is mutually
exclusive with any explicit timout passing to the watchdogs.
The last timeout can be returned via the wdog_kern_last_timeout()
KPI.
- Add the possibility to pat the watchdogs installed via the watchdog(9)
interface from the kernel.
In order to do that the new KPI wdog_kern_pat() is offered and it does
accept normalized nanoseconds or WD_LASTVAL.
- Avoid to pass WD_ACTIVE down in the watchdog handlers. All the control
bit processing should over to the upper layer functions and not passed
down to the handlers at all.
These changes are intended to be used in order to fix up the watchdog
tripping in situation when the userland is busted, but protection is still
wanted (examples: shutdown syncing / disk dumping).
Sponsored by: Sandvine Incorporated
Reviewed by: emaste, des, cognet
MFC after: 2 weeks
bound to an AP before SMP has started, the system will panic when we try
to touch per-CPU state for that AP because that state has not been
initialized yet. Fix this in the same way as ULE: place all threads in
the global run queue before SMP has started.
Reviewed by: jhb
MFC after: 1 month
will generate a short terminated USB transfer if
the maximum NCM frame size is greater than what
the driver can handle.
Reported by: Matthias Benesch
MFC after: 7 days
Approved by: thompsa (mentor)
device in /dev/ create symbolic link with adY name, trying to mimic old ATA
numbering. Imitation is not complete, but should be enough in most cases to
mount file systems without touching /etc/fstab.
- To know what behavior to mimic, restore ATA_STATIC_ID option in cases
where it was present before.
- Add some more details to UPDATING.
counting memory being dumped in 16MB increments is somewhat silly.
Especially if the dump fails and everything you've got for debugging
is screen filled with numbers in 16 decrements... Replace that with
percentage-based progress with max 10 updates all fitting into one
line.
Collapse other very "useful" piece of crash information (total ram) into
the same line to save some more space.
MFC after: 1 week
when building kernels that don't have "options NFS_ROOT"
specified. I plan on moving the functions that use these
data structures into the shared code in sys/nfs/nfs_diskless.c
in a future commit. At that time, these definitions will no
longer be needed in nfs_vfsops.c and nfs_clvfsops.c.
MFC after: 2 weeks
mechanism. The caller may specify a timeout in ticks after which the
task will be scheduled.
Sponsored by: The FreeBSD Foundation
Reviewed by: jeff, jhb
MFC after: 1 month
- Also a couple minor tweaks to the TX code from the same source.
- Add the INET ioctl code which has been missing from this driver,
and which caused IP aliases to reset the interface.
- Last, some minor logic changes that just reflect upcoming
hardware support, but have no other functional effect now.
MFC after a week
same diskless NFS root code as the regular client, which
was moved to sys/nfs by r221032. This fixes the newnfs
client so that it can do an NFSv3 diskless root file system.
MFC after: 2 weeks
set the f_flags field of "struct statfs". This had the interesting
effect of making the NFSv4 mounts "disappear" after r221014,
since NFSMNT_NFSV4 and MNT_IGNORE became the same bit.
Move the files used for a diskless NFS root from sys/nfsclient
to sys/nfs in preparation for them to be used by both NFS
clients. Also, move the declaration of the three global data
structures from sys/nfsclient/nfs_vfsops.c to sys/nfs/nfs_diskless.c
so that they are defined when either client uses them.
Reviewed by: jhb
MFC after: 2 weeks
As long as this is a costy function, even when compiled in (along with
the option TCP_SIGNATURE), it can be disabled via the
net.inet.tcp.signature_verify_input sysctl.
Sponsored by: Sandvine Incorporated
Reviewed by: emaste, bz
MFC after: 2 weeks
defines struct in6_addr, which is needed by ip6_hdr used in here.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 5 days
INET or INET6 as it holds all the IPPROTO_* definitions needed
for the SYSCTL_NODE definitions.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 5 days
unconditionally backing out r193997, so that they are available for
IPv6-only setups as well.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 5 days
set the f_flags field of "struct statfs". This had the interesting
effect of making the NFSv4 mounts "disappear" after r221014,
since NFSMNT_NFSV4 and MNT_IGNORE became the same bit.
MFC after: 2 weeks
"struct nfs_args" as the regular NFS client. This is needed
so that the old mount(2) syscall will work and it makes
sharing of the diskless NFS root code easier. Eary in the
porting exercise I introduced a new revision of nfs_args, but
didn't actually need it, thanks to nmount(2). I re-introduced the
NFSMNT_KERB flag, since it does essentially the same thing and
the old one would not have been used because it never worked.
I also added a few new NFSMNT_xxx flags to sys/nfsclient/nfs_args.h
that are used by the experimental NFS client.
MFC after: 2 weeks
Writing the TX power registers is the same between all of these chips
and later NICs (AR9287, AR9271 USB, etc.) so this will reduce code
duplication when those NICs are added to the HAL.
goes to zero. E.g., the vnode might be only shared-locked at the time of
vput() call. Such vnodes are kept in the hash, so they can be found later.
If ffs_valloc() allocated an inode that has its vnode cached in hash, and
still owing the inactivation, then vget() call from ffs_valloc() clears
VI_OWEINACT, and then the vnode is reused for the newly allocated inode.
The problem is, the vnode is not reclaimed before it is put to the new
use. ffs_valloc() recycles vnode vm object, but this is not enough.
In particular, at least v_vflag should be cleared, and several bits of
UFS state need to be removed.
It is very inconvenient to call vgone() at this point. Instead, move
some parts of ufs_reclaim() into helper function ufs_prepare_reclaim(),
and call the helper from VOP_RECLAIM and ffs_valloc().
Reviewed by: mckusick
Tested by: pho
MFC after: 3 weeks
bytes. Remove bogus assertion and while here remove another too obvious
assertion.
Reported by: Fabian Keil <freebsd-listen@fabiankeil.de>
MFC after: 2 weeks
stack. It means that all legacy ATA drivers are disabled and replaced by
respective CAM drivers. If you are using ATA device names in /etc/fstab or
other places, make sure to update them respectively (adX -> adaY,
acdX -> cdY, afdX -> daY, astX -> saY, where 'Y's are the sequential
numbers for each type in order of detection, unless configured otherwise
with tunables, see cam(4)).
ataraid(4) functionality is now supported by the RAID GEOM class.
To use it you can load geom_raid kernel module and use graid(8) tool
for management. Instead of /dev/arX device names, use /dev/raid/rX.
Hold the vnode around the region where object lock is dropped, until
vnode lock is acquired.
Do not drop the vnode reference for a case when the object was
deallocated during unlock. Note that in this case, VV_TEXT is cleared
by vnode_pager_dealloc().
Reported and tested by: pho
Reviewed by: alc
MFC after: 3 days
the mutexes in the wrong order for the case where the
MBF_MNTLSTLOCK is set. I believe this did have the
potential for deadlock. For example, if multiple nfsd threads
called vfs_busyfs(), which calls vfs_busy() with MBF_MNTLSTLOCK.
Thanks go to pho for catching this during his testing.
Tested by: pho
Submitted by: kib
MFC after: 2 weeks
spurious (and fatal) interrupt errors.
One user reported seeing this:
Apr 22 18:04:24 ceres kernel: ar5416GetPendingInterrupts: fatal error,
ISR_RAC 0x0 SYNC_CAUSE 0x2000
SYNC_CAUSE of 0x2000 is AR_INTR_SYNC_LOCAL_TIMEOUT which is a bus timeout;
this shouldn't cause HAL_INT_FATAL to be set.
After checking out ath9k, ath9k_ar9002_hw_get_isr() clears (*masked)
before continuing, regardless of whether any bits in the ISR registers
are set. So if AR_INTR_SYNC_CAUSE is set to something that isn't
treated as fatal, and AR_ISR isn't read or is read and is 0, then
(*masked) wouldn't be cleared. Thus any of the existing bits set
that were passed in would be preserved in the output.
The caller in if_ath - ath_intr() - wasn't setting the masked value
to 0 before calling ath_hal_getisr(), so anything that was present
in that uninitialised variable would be preserved in the case above
of AR_ISR=0, AR_INTR_SYNC_CAUSE != 0; and if the HAL_INT_FATAL bit
was set, a fatal condition would be interpreted and the chip was
reset.
This patch does the following:
* ath_intr() - set masked to 0 before calling ath_hal_getisr();
* ar5416GetPendingInterrupts() - clear (*masked) before processing
continues; so if the interrupt source is AR_INTR_SYNC_CAUSE
and it isn't fatal, the hardware isn't reset via returning
HAL_INT_FATAL.
This doesn't fix any underlying errors which trigger
AR_INTR_SYNC_LOCAL_TIMEOUT - which is a bus timeout of some
sort - so that likely should be further investigated.
r216801
- cosmetic changes and style fixes
- Trick GAS/GCC into compiling access to TICK/(S)TICK_COMPARE independently
of the selected instruction set. Moreover, sun4v doesn't need the WAR for
BlackBird CPUs.
- Rename the "xor" parameter to "xorval" as the former is a reserved keyword
in C++.
vfs_sanitizeopts() can handle "ro" and "rw" options properly, there is
no more need to add "noro" in vfs_donmount() to cancel "ro".
This also fixes a problem of canceling options beginning with "no".
For example, "noatime" didn't cancel "nonoatime". Thus it was possible
that both "noatime" and "nonoatime" were active at the same time.
Reviewed by: bde
- Centralize PCI resource allocation/release.
- Enable flowid (TSS) support.
- Added "per-fastpath" locks and watchdog timeouts.
- Fixed problem where the CQ producer index was advanced beyond
the size of the CQ ring during initialization.
- Replaced hard-coded debug levels in some debug print statements.
- More style(9) fixes.
MFC after: Two weeks
r220375 all drivers enabled in the sparc64 GENERIC should be either
correctly using bus_dmamap_sync(9) calls or supply BUS_DMA_COHERENT
when appropriate or as a workaround for missing bus_dmamap_sync(9)
calls (sound(4) drivers and partially sym(4)). In at least some
configurations taking advantage of the streaming cache results in
a modest performance improvement.
- Remove the memory barrier for BUS_DMASYNC_PREREAD which as the
comment already suggested is bogus.
- Add my copyright for having implemented several things like support
for the Fire and Oberon IOMMUs, taking over PROM IOMMU mappings etc.
should respond with all zeroes to any access to slave registers. Test with
PATA devices confirmed such behavior. Unluckily, Intel SATA controllers in
legacy emulation mode behave differently, not making any difference between
ATA and ATAPI devices. It causes false positive slave device detection and,
as result, command timeouts.
To workaround this problem, mask result of legacy-emulated soft-reset with
the device presence information received from the SATA-specific registers.
nm_maxfilesize. This value rarely, if ever, changes
and the nm_mtx mutex is locked/unlocked earlier in
the function, which should be sufficient to avoid
getting a stale cached value for it. There is a
discussion w.r.t. what these tests should be, but
I've left them basically the same as the regular
NFS client for now.
Suggested by: pjd
MFC after: 2 weeks
- TCO_MESSAGEx: TCO specific regs providing the ability to monitor BIOS
bootup activity.
- TCO_NEWCENTURY: reporting RTC year roll over.
- TCO_NMI2SMI_EN, TCO_NMI_NOW: controlling SMIs conversion to NMIs and
NMI trigger.
- SMI_GBL_EN: Enabling SMI delivery for all the northbridge controller.
MFC after: 10 days
allocate all of them at attach time. This allows to avoid moving
keys around in the most-recently-used queue and needs no mutex
synchronization nor refcounting.
MFC after: 2 weeks
create reasonably large cache for the keys that is filled when
needed. The previous version was problematic for very large providers
(hundreds of terabytes or serval petabytes). Every terabyte of data
needs around 256kB for keys. Make the default cache limit big enough
to fit all the keys needed for 4TB providers, which will eat at most
1MB of memory.
MFC after: 2 weeks
This improves hard-reset and hot-plug on these ports.
- Device with ID 0x29218086 is a 2-port variant of ICH9 in legacy mode.
Skip probing for nonexistent slave devices there.
It allows to avoid false positive device detection under Xen, that caused
long probe delays due to subsequent IDENTIFY command timeouts.
MFC after: 1 month
This is destined to be a lightweight and optional set of ALQ
probes for debugging events which are just impossible to debug
with printf/log (eg packet TX/RX handling; AMPDU handling.)
The probes and operations themselves will appear in subsequent
commits.
so that it won't try and use vp->v_mount to do an RPC during
a forced dismount. There needs to be at least one more kernel
commit, plus a change to the umount(8) command before forced
dismounts will work for the experimental NFS client.
MFC after: 2 weeks
that could have allowed the hardware pidx to reach the cidx even though
the freelist isn't empty. (Haven't actually seen this but it was there
waiting to happen..)
MFC after: 1 week
While in_pseudo() etc. is often used in offloading feature support,
in_cksum() is mostly used to fix some broken hardware.
Keeping both around for the moment allows us to compile NIC drivers
even in an IPv6 only environment without the need to mangle them
with #ifdef INETs in a way they are not prepared for. This will
leave some dead code paths that will not be exercised for IPv6.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 3 days
Not compiling in and not initializing from inetsw from in_proto.c for
IPv6 only, we need to initialize upper layer protocols from inet6sw.
Make sure to not initialize them twice in a Dual-Stack
environment but only conditionally on no INET as we have done for
TCP for a long time. Otherwise we would leak resources.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 3 days
When compiling out INET we still need the initialization routines
as well as the tuning and montoring sysctls shared with IPv6.
Move the two send/recvspace variables up from the middle of the
file to ease compiling out the INET only code.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 3 days
Move the ipport_tick_callout and related functions from ip_input.c
to in_pcb.c. The random source port allocation code has been merged
and is now local to in_pcb.c only.
Use a SYSINIT to get the callout started and no longer depend on
initialization from the inet code, which would not work in an IPv6
only setup.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
Move fw_one_pass to where it belongs: it is a property of ipfw,
not of ip_input.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 3 days
experimental NFS client to take care of overflows for the calls
above the buffer cache layer in a manner similar to r220876.
Thanks go to dillon at apollo.backplane.com for providing the
snippet of code that does this.
MFC after: 2 weeks
experimental NFS client to take care of overflows. Thanks
go to dillon at apollo.backplane.com for providing the
snippet of code that does this.
MFC after: 2 weeks
now a suitable base for all kinds of egress queues.
- Add control queues (sge_ctrlq) and allocate one of these per hardware
channel. They can be used to program filters and steer traffic (and
more).
MFC after: 1 week
- If a ENH_SENS TLV section exit the firmware is capable of doing
enhanced sensitivity calibration.
- Newer devices/firmwares have more calibration commands therefore
hardcoding the noise gain/reset commands no longer works. It is
supposed to use the next index after the newest calibration type
support. Read the command index of the TLV section if available.
This support has not worked for several years, and is not likely to work
again, unless Intel decides to release a native FreeBSD version of their
compiler. ;)
calculate required memory size dynamically.
- Fix races on chain re-lock.
- Introduce new field to ip_fw_chain - generation count. Now utilized
only in the NAT configuration, but can be utilized wider in ipfw.
- Get rid of NAT_BUF_LEN in ip_fw.h
PR: kern/143653
specified minimum and maximum. In case when specified default value
is out of bounds it does not work as expected and does not limit
variable. Check that default value is in range and limit it if needed.
Also bump max_hash_size value to 65536 to correspond with manual page.
PR: kern/152887
MFC after: 2 weeks
within the experimental NFS client. Mostly add mutex locking
and use the same rsize, wsize during the operation by keeping
a local copy of it. This is another change that brings it
closer to the regular NFS client.
MFC after: 2 weeks
adding the check to nfsrpc_close() isn't useful. Also,
the check in nfscl_getcl() must be more involved, since
it needs to check before and after the acquisition of
the refcnt on nfsc_lock, while the mutex that protects
the client state data is held.
Add pmap_invalidate_cache_pages() method on x86. It flushes the CPU
cache for the set of pages, which are not neccessary mapped. Since its
supposed use is to prepare the move of the pages ownership to a device
that does not snoop all CPU accesses to the main memory (read GPU in
GMCH), do not rely on CPU self-snoop feature.
amd64 implementation takes advantage of the direct map. On i386,
extract the helper pmap_flush_page() from pmap_page_set_memattr(), and
use it to make a temporary mapping of the flushed page.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
don't force a window update if the window would not actually grow due to
window scaling. Specifically, if the window scaling factor is larger than
2 * MSS, then after the local reader has drained 2 * MSS bytes from the
socket, a window update can end up advertising the same window. If this
happens, the supposed window update actually ends up being a duplicate ACK.
This can result in an excessive number of duplicate ACKs when using a
higher maximum socket buffer size.
Reviewed by: bz
MFC after: 1 month
vop_stdallocate() is filesystem agnostic and will run as slow as a
read/write loop in userspace; however, it serves to correctly
implement the functionality for filesystems that do not implement a
VOP_ALLOCATE.
Note that __FreeBSD_version was already bumped today to 900036 for any
ports which would like to use this function.
Also reserve space in the syscall table for posix_fadvise(2).
Reviewed by: -arch (previous version)
for a case that will probably never happen. It can only
happen if a server were to successfully lookup a file, but not
return attributes for that file. Although technically allowed
by the NFSv3 RFC, I doubt any server would ever do this.
However, if it did, the client would have not vput()'d the
new vnode when it needed to do so.
MFC after: 2 weeks
that would be needed if, in the future, nfscl_loadattrcache()
were to return an error. Currently nfscl_loadattrcache()
never returns an error, so these cases never currently happen.
MFC after: 2 weeks
experimental NFS client's vnode op functions to make
them compatible with the regular NFS client. I'll admit
I'm not sure that the mutex locks around the assignments
are needed, but the regular client has them, so I added them.
Also, add handling of the case of partial attributes in
setattr to be compatible with the regular client.
MFC after: 2 weeks
functions, so that threads don't get stuck in them during
a forced dismount. nfs_sync/VFS_SYNC() needs this, since it is
called by dounmount() before VFS_UNMOUNT(). The nfscl_nget()
case makes sure that a thread doing an VOP_OPEN() or
VOP_ADVLOCK() call doesn't get blocked before attempting
the RPC. Attempting RPCs don't block, since they all
fail once a forced dismount is in progress.
The third one at the beginning of nfsrpc_close()
is done so threads don't get blocked while doing VOP_INACTIVE()
as the vnodes are cleared out.
With these three changes plus a change to the umount(1)
command so that it doesn't do "sync()" for the forced case
seem to make forced dismounts work for the experimental NFS
client.
MFC after: 2 weeks
message that was generated when doing experimental NFS client
mounts. I put that message in because the krpc would hang with
the default size for mounts that used large rsize/wsize values.
Since the bug that caused these hangs was fixed by r213756,
I think the message is no longer needed.
MFC after: 2 weeks
While it does not provide any functionality for IPv6, it provides
the sysctl nodes for net.inet.* that a lot of functionality shared
between IPv4 and IPv6 depends on. We cannot change these anymore
without breaking a lot of management and tuning.
In case of IPv6 only, we compile out everything but the sysctl node
declarations.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC After: 5 days
passing the cached proxydl reference (sockaddr_dl initialized or not) to
nd6_na_output(). nd6_na_output() will thus assume a proxy NA. Revert to
conditionally passing either &proxydl or NULL if no proxy case desired.
Tested by: ipv6gw and ref9-i386
Reported by: Pete French (petefrench ingresso.co.uk on stable)
Reported by: bz, simon on Y! cluster
Reported by: kib
PR: kern/151908
MFC after: 3 days
If various checks are omitted, the CMSG_NXTHDR macro expands to
(struct cmsghdr *)((char *)(cmsg) + \
_ALIGN(((struct cmsghdr *)(cmsg))->cmsg_len))
Although there is no alignment problem (assuming cmsg is properly aligned
and _ALIGN is correct), this violates -Wcast-align on strict-alignment
architectures. Therefore an intermediate cast to void * is appropriate here.
There is no workaround other than not using -Wcast-align.
MFC after: 2 weeks
The code provides information on how the signal was generated.
Formerly, the code was only logged for traps, much like only signal handlers
for traps received a meaningful si_code before FreeBSD 7.0.
In rare cases, no information is available and 0 is still logged.
MFC after: 1 week
same as the regular NFS client for NFSv3. The main one is making
use of a reserved port# the default. Also, set the retry limit
for TCP the same and fix the code so that it doesn't disable
readdirplus for NFSv4.
MFC after: 2 weeks
It's also marked inactive by the initvals, and enabled after
the baseband/PLL has been configured, but before the RF
registers have been programmed.
The origin and reason for this particular change is currently unknown.
Obtained from: Linux ath9k
- 6000 series devices need enhanced sensitivity calibration.
- 6000 series devices need a different setting for the shadow reg.
- set the IWN_FLAG_HAS_11N bit if the EEPROM says the device has 11n
support.
Obtained from: OpenBSD
Antenna diversity on the >= AR5416 is implemented differently than the
AR5212 and previous chips. So for now, and not to confuse things, just
disable it for now.
- read RSSI only for the active chains
- cast RSSI/NF to int8_t before passing it up to radiotap
- remove the htole64() for the timestamp
Obtained from: OpenBSD
- Mark getc() as inline, this has no effect on gcc but helps clang.
- Move getc() body before xgetc() so gcc does not emit a warning about
function having no body.
threads in the same manner as the regular NFS client after
r214026 was committed. This resolves the lors fixed by r214026
and its predecessors for the regular client.
Reviewed by: jhb
MFC after: 2 weeks
- there is a local variable for sc->fw_dma, use that instead
- OpenBSD uses 5*hz to wait for firmware to be loaded
- in case the firmware module contains invalid data, actually release it
- use ATA_SE_EXCHANGED (SError.DIAG.X) bit to detect hot-plug events when
power-management enabled and ATA_SE_PHY_CHANGED (SError.DIAG.N) can't be
trusted;
- on controllers supporting staggered spin-up (SS) put unused channels
into Listen state instead of Off. It should still save some power, but
allow plug-in events to be detected;
- on controllers supporting cold presence detection (CPD), when power
management enabled, use CPD events to detect hot-plug in addition to PHY
events.
down. The ingress queue lock was unused and has been removed as part of
these changes.
- An in-flight egress update from the SGE must be handled before the
queue that requested it is destroyed. Wait for the update to arrive.
- Interrupt handlers must stop processing rx events for a queue before
the queue is destroyed. Events that have not yet been processed
should be ignored once the queue disappears.
MFC after: 1 week
to determine if a file system supports NFSv4 ACLs. Since
VOP_PATHCONF() must be called with a locked vnode, the function
is called before nfsvno_fillattr() and the result is passed in
as an extra argument.
MFC after: 2 weeks
crossing of server mount points properly. The functions
nfsvno_fillattr() and nfsv4_fillattr() were modified to
take the extra arguments that are the mount point, a flag
to indicate that it is a file system root and the mounted
on fileno. The mount point argument needs to be busy when
nfsvno_fillattr() is called, since the vp argument is not
locked.
Reviewed by: kib
MFC after: 2 weeks
invariant and APERF/MPERF MSRs exist but these MSRs never tick. When we
calculate effective frequency from cpu_est_clockrate(), it caused panic of
division-by-zero. Now we test whether these MSRs actually increase to avoid
such foot-shooting.
Reported by: dim
Tested by: dim
from scratch. Remove htole16() calls, rxon.chan is an uint8_t,
ieee80211_chan2ieee() does return an ic_ieee as an int, but I heavily
doubt a htole16() will buy us anything here.
- IWN_TXOP_TO_US is equal to IEEE80211_TXOP_TO_US
- use IEEE80211_DUR_TU
- ieee80211_add_rates/ieee80211_add_xrates are public, use em
- copied ieee80211_add_ssid it is not public
32 bits. Some times compiler inserts unnecessary instructions to preserve
unused upper 32 bits even when it is casted to a 32-bit value. It reduces
such compiler mistakes where every cycle counts.
Instead of spinning in a tight loop for up to 15 seconds, polling for device
readiness while it spins up, return reset completion just after PHY reports
"connect well" or 100ms connection timeout. If device was found, use callout
for checking device readiness with 100ms period up to full 31 second timeout.
This fixes system freeze for 5-10 seconds on drives hot plug-in.
mount point crossings correctly. It was testing the wrong flag.
Also, try harder to make sure that the fsid is different than
the one assigned to the client mount point, by hashing the
server's fsid (just to create a different value deterministically)
when it is the same.
MFC after: 2 weeks
details of each rman header, but not the contents of all rman structures
in the system. This is especially useful on platforms where some rmans
have many thousands of entries in rmans, making scrolling through the
output of "show all rman" impractical. Individual rmans can then be viewed
including their contents with "show rman 0xaddr" as usual.
Reviewed by: jhb
- make SATA SIMs announce capabilities to handle SDB with Notification bit;
- make PMP driver honor this SIMs capability;
- make SATA XPT to negotiate and enable this feature for ATAPI devices.
This feature allows supporting SATA ATAPI devices to inform system about
some events happened, that may require attention. In my case this allows
LG GH22LS50 SATA DVR-RW drive to report tray open/close events. Events
reported to CAM in form of AC_SCSI_AEN async. Further they could be used
as a hints for checking device status and reporting media change to upper
layers, for example, via spoiling mechanism of GEOM.
diversity.
This is bit dirty and likely should be revised at a later date,
with an eye to unifying/tidying up the whole diversity setup
and allowing developers to do "tricky stuff" as they desire.
For now, this works.
* add a new method, specifically for doing per-RX packet
antenna diversity
* set that HAL method only if it's Kite and a Kite chip that
does diversity.
* add a diversity flag to the HAL debugging section
* add a check to make sure the kite diversity code doesn't run
on boards that don't require it, as not all Kite chips will
implement it.
* add some debug statements when the diversity code makes
changes to the antenna diversity/combining setup.
controller port readiness (that should set just after PHY ready signal),
reduce wait time from 10s to 1s before trying more aggressive reset method.
This should improve system responsibility in some failure conditions.
Note: this HAL currently only supports the AR9285.
From Linux ath9k:
The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.
The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.
The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
not believe that these leaks had a practical impact,
since the situations in which they would have occurred
would have been extremely rare.
MFC after: 2 weeks
MPERF MSRs are available. It was disabled in r216443. Remove the earlier
hack to subtract 0.5% from the calibrated frequency as DELAY(9) is little
bit more reliable now.
Instead of spinning in a tight loop for up to 15 seconds, polling for device
readiness while it spins up, return reset completion just after PHY reports
"connect well" or 100ms connection timeout. If device was found, use callout
for checking device readiness with 100ms period up to full 31 second timeout.
This fixes system freeze for 5-10 seconds on drives hot plug-in.
embedded flash stores.
Some devices - notably those with uboot - don't have an
explicit partition table (eg like Redboot's FIS.)
geom_map thus provides an easy way to export the hard-coded
flash layout as geom providers for use by filesystems and
other tools.
It also includes a "search" function which allows for
dynamic creation of partition layouts where the device only
has a single hard-coded partition. For example, if
there is a "kernel+rootfs" partition, a single image can
be created which appends the rootfs after the kernel with
an appropriate search string. geom_map can be told to
search for said search string and create a partition
beginning after it.
Submitted by: Aleksandr Rybalko <ray@dlink.ua>
bus driver at detach, hence ehci_detach() does exactly this since r199718.
Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)
of NFSv2 getting an error return from VOP_MKNOD(). Without this
patch, the server file system remains busy after an NFSv2
VOP_MKNOD() fails.
MFC after: 2 weeks
SCSI status errors to CAM (that was wrong, as it too often turned retriable
wire errors into non-retriable REQUEST SENSE errors), do it only for STALL
errors on control pipe of the CBI devices. STALL on control pipe is just
a one of the ways to report error for CBI devices.
PR: usb/150401, usb/154593.
Reviewed by: hselasky
MFC after: 1 week
for a new journal specific partial truncate routine.
- Use dep_current[] in place of specific dependency counts. This is
automatically maintained when workitems are allocated and has
less risk of becoming incorrect.
the experimental NFS server, so that it doesn't leak memory
when unloaded. However, unloading the NFSv4 server is not
recommended, since all NFSv4 state will be lost by the unload
and clients will have to recover the state after a server
reload/restart as if the server crashed/rebooted.
MFC after: 2 weeks
- Keep a hash of indirect blocks that have recently been freed and are
still referenced in the journal.
- Lookup blocks in this hash before forcing a new block write to wait on
the journal entry to hit the disk. This is only necessary to avoid
confusion between old identities as indirects and new identities as
file blocks.
- Don't free jseg structures until the journal has written a record that
invalidates it. This keeps the indirect block information around for
as long as is required to be safe.
- Force an empty journal block write when required to flush out stale
journal data that is simply waiting for the oldest valid sequence
number to advance beyond it.
VOP_LOOKUP() returned. This fixes a bug in the experimental
NFS server for the case where VFS_VGET() fails returning EOPNOTSUPP
in the ReaddirPlus RPC, forcing the use of VOP_LOOKUP() instead.
MFC after: 2 weeks
workaround for fdescfs to not panic when ncookies is not NULL, similar
to the one committed as r152254, but simpler, due to fdescfs_readdir()
not calling vfs_read_dirent().
PR: kern/156177
MFC after: 1 week
working. We store v4 and v6 addresses as a union but for v4-mapped
addresses only store the 32bits w/o the ::ffff: word. That failed the
check as for example 127.0.0.1 would be ::7f00:1 rather than ::ffff:7f00:1
and the IN6_IS_ADDR_V4MAPPED() never worked here. Given we can hardly get
here with an unbound local address or invalid inp_vflags remove the check.
Reported by: tuexen
Reviewed by: tuexen
MFC after: 3 days
some more. Similar to what we do for TCP check for v4-mapped
addresses and then handle them or the normal v6 address case.
For either set inp_vflags before calling into the pcb connect
function so that we have an unambiguous view in case we need to
set the local address or port.
Looked at: tuexen (as part of more)
MFC after: 3 days
update_gdt_{f,g}sbase. The functions set the flag when td == curthread,
and sysarch is always called with curthread.
Reviewed by: jhb, jkim
MFC after: 1 week
Thread might be preempted after testing, which causes the flag to be
cleared. If ast was not delivered, we will do sysret with potentially
wrong fs/gs bases.
Reviewed by: jhb, jkim
MFC after: 1 week (together with r220430, r220452)
for a detailed explanation of the problems).
The only difference with the previous fix is in Solution2:
CPUBLOCK is no longer set when exiting from callout_reset_*() functions,
which avoid the deadlock (leading to r217161).
There is no need to CPUBLOCK there because the running-and-migrating
assumption is strong enough to avoid problems there.
Furthermore add a better !SMP compliancy (leading to shrinked code and
structures) and facility macros/functions.
Tested by: gianni, pho, dim
MFC after: 3 weeks
on per-device basis.
- While adding support for per-device sysctls, merge from graid branch
support for ADA_TEST_FAILURE kernel option, which opens few more sysctl,
allowing to simulate read and write errors for testing purposes.
return. The ast() function may cause a context switch in which case
PCB_FULL_IRET would be set in the pcb. However, the code was not
rechecking the flag after ast() returned and would not properly restore
the FSBASE and GSBASE MSRs. To fix, recheck the PCB_FULL_IRET flag after
ast() returns.
While here, trim an instruction (and memory access) from the doreti path
and fix a typo in a comment.
MFC after: 1 week
This introduces struct ieee80211_rx_stats - which stores the various kinds
of RX statistics which a MIMO and non-MIMO 802.11 device can export.
It also fleshes out the mimo export to userland (node_getmimoinfo()).
It assumes that MIMO radios (for now) export both ctl and ext channels.
Non-11n MIMO radios are possible (and I believe Atheros made at least
one), so if that chipset support is added, extra flags to the
struct ieee80211_rx_stats can be added to extend this support.
Two new input functions have been added - ieee80211_input_mimo() and
ieee80211_input_mimo_all() - which MIMO-aware devices can call with
MIMO specific statistics.
802.11 devices calling the non-MIMO input functions will still function.
ctl/ext noise floor values.
This routine doesn't check to see whether the radio is MIMO
capable - instead, it simply returns either the raw values,
the "nominal" values if the raw values aren't yet available
or are invalid, or '0' values if there's no valid channel/
no valid MIMO values.
Callers are expected to verify the radio is a MIMO radio
(which for now means it's an 11n chipset, there are non-11n
MIMO chipsets out there but I don't think we support them,
at least in MIMO mode) before exporting the MIMO values.
upper-level HAL.
Right now the per-chain noise floor values aren't used anywhere in
the upper-level HAL, so the driver currently has no real reference
to compare the per-chain RSSI values to.
This is needed before per-chain RSSI values (for ctl and ext radios)
are can be thrown upstairs to the net80211 code.
safer for i386 because it can be easily over 4 GHz now. More worse, it can
be easily changed by user with 'machdep.tsc_freq' tunable (directly) or
cpufreq(4) (indirectly). Note it is intentionally not used in performance
critical paths to avoid performance regression (but we should, in theory).
Alternatively, we may add "virtual TSC" with lower frequency if maximum
frequency overflows 32 bits (and ignore possible incoherency as we do now).
path via the sysretq instruction to return from the system call. This was
removed in 190620 and not quite fully restored in 195486. This resolves
most of the performance regression in system call microbenchmarks between
7 and 8 on amd64.
Reviewed by: kib
MFC after: 1 week
chain to be corrupted.
- Removed many console print warnings and replaced with driver maintained
counters.
- Several style(9) fixes.
MFC after: One week.
will be removed. Permit the journal to proceed so that we don't leave
a rollback in a cg for a very long time as this can cause terrible perf
problems in low memory situations.
Tested by: pho
functions are implemented with CMPXCHG8B instruction where it is available,
i. e., all Pentium-class and later processors. Note this instruction is
also used for atomic_store_rel_64() because a simple XCHG-like instruction
for 64-bit memory access does not exist, unfortunately. If the processor
lacks the instruction, i. e., 80486-class CPUs, two 32-bit load/store are
performed with interrupt temporarily disabled, assuming it does not support
SMP. Although this assumption may be little naive, it is true in reality.
This implementation is inspired by Linux.
improves command timeout handling.
Many thanks to Areca for continuing to support FreeBSD.
Submitted by: Ching-Lung Huang <ching2048 areca com tw>
MFC after: 2 months
for racct.
Note that after this commit, ipcs(1) needs to be rebuilt. Otherwise, it will
fail with "ipcs: sysctlbyname: kern.ipc.msqids: Cannot allocate memory".
Sponsored by: The FreeBSD Foundation
Reviewed by: kib (earlier version)
This fixes a long standing bug in mxge(4) where "ifconfig mxge0 $IP"
did not bring the interface into a RUNNING state, like it does on
most (all?) other FreeBSD NIC drivers.
Thanks to gnn for mentioning the bug, and yongari for pointing out that
ether_ioctl() invokes ifp->if_init() in SIOCSIFADDR.
MFC after: 7 days
- Add the change made in em to the actual unrefreshed number
of descriptors is used as a basis in rxeof on the way out
to determine if more refresh is needed. NOTE: there is a
difference in the ring setup in igb, this is not accidental,
it is necessitated by hardware behavior, when you reset the
newer adapters it will not let you write RDH, it ALWAYS sets
it to 0. Thus the way em does it is not possible.
- Change the sysctl handling of flow control, it will now make
the change dynamically when the variable setting changes rather
than requiring a reset.
- Change the eee sysctl naming, validation found the old unintuitive :)
- Last but not least, some important performance tweaks in the TX
path, I found that UDP behavior could be drastically hindered or
improved with just small changes in the start loop. What I have
here is what testing has shown to be the best overall. Its interesting
to note that changing the clean threshold to start at a full half of
the ring, made a BIG difference in performance. I hope that this
will prove to be advantageous for most workloads.
MFC in a week.
up and declaring a filesystem out of space. Especially necessary when
running on a small filesystem. With this improvement, it should be
possible to use soft updates on a small root filesystem.
Kudos to: Peter Holm
Testing by: Peter Holm
MFC: 2 weeks
show that there are perfectly working PM timers with occasional "hiccups",
probably because of an SMI. Now we ignore the maximum if it happens once in
the test loop and the width is small enough. Also, relax normal width a bit
to count in a boundary case.
Unlike other controllers which have more advanced jumbo support,
these controllers have one send ring, one standard receive producer
ring and one receive return ring. In order to receive jumbo frames
on the controllers, driver now will increase Rx buffer size to 9k.
Two Rx modes are supported on these controllers and I chose
standard Rx BDs over extended Rx BDs. The extended Rx BD mode
allows up to 4 segmentations for each Rx BDs such that kernel does
not have to allocate large buffer of contiguous memory for
receiving. The extended Rx BD mode is already used on controllers
that have separate jumbo receive ring. However, using extended Rx
BDs on BCM5714/BCM5715/BCM5780 reduces the number of Rx BDs to 256
entries which in turn may reduce the performance. Also UMA backed
page allocator for jumbo frame returns contiguous memory so using
extended Rx BD has no advantage on FreeBSD unless highly customized
local allocator implemented in driver is used.
To use jumbo buffers in standard receive ring, Rx buffer allocation
handler was changed to allocate MJUM9BYTES sized mbuf.
PR: kern/155192
Tested by: Vijay Singh <vijju.singh <> gmail dot com>
Submitted by: mjacob (initial version)
value.
The timeout is expressed in the form T(N) = (2^N * nanoseconds) and can
be easilly extracted from the watchdog interface as a WD_TO_* macro.
That new functionality is supposed to fix re-entering the kernel from DDB
re-enabling the watchdog again (previously disabled) and also offer the
possibility to break for deadlocked DDB commands.
Please note that retro-compatibility is retained.
Sponsored by: Sandvine Incorporated
Approved by: des
MFC after: 10 days
levels. TX would hang, RX wouldn't. A bit of digging showed the interface
send queue was full, but IFF_DRV_OACTIVE was clear and the hardware TX
queue was empty.
It turns out that there wasn't a check to drain the interface send
queue once hardware TX had completed, so if the interface send queue
had filled up in the meantime, subsequent packets would be dropped
by the higher layers and if_start (and thus arge_start()) would never
be called.
The fix is simple - call arge_start_locked() in the software interrupt
handler after the hardware TX queue has been handled or a TX underrun
occured. This way the interface send queue gets drained.
at run-time on i386. cpu_ticks() is set to use RDTSC early enough on i386
where it is available. Otherwise, cpu_ticks() is driven by the current
timecounter hardware as binuptime(9) does. This also avoids unnecessary
namespace pollution from <machine/cputypes.h>.
This modifies CFLAGS and tweaks sio.S to use the new calling convention.
The sio_init() and sio_putc() prototypes are modified so that other
users of this code know the correct calling convention.
This makes the code smaller when compiled with clang.
Reviewed by: jhb
Tested by: me and Freddie Cash <fjwcash gmail com>
on the fact that real hardware has almost fixed cost to read the ACPI timer.
It is virtually always false for hardware emulation and it makes no sense to
read it multiple times, which is already quite expensive for full emulation.
to the l_load() method in the file_formats structure, while being passed
an address as an argument (dest). With file_load() calling arch_loadaddr()
now, this bug is a little bit more significant.
Spotted by: nyan@ (nice catch!)
From the ath9k source:
==
11N: we can no longer afford to self link the last descriptor.
MAC acknowledges BA status as long as it copies frames to host
buffer (or rx fifo). This can incorrectly acknowledge packets
to a sender if last desc is self-linked.
==
Since this is useful for pre-AR5416 chips that communicate PHY errors
via error frames rather than by on-chip counters, leave the support
in there, but disable it for AR5416 and later.
from the interface index, then decrease refcount, not vice versa.
Otherwise there is a race (reproducible) when if_free_internal()
contests on IFNET_WLOCK(), and we got a zero-refed ifnet in the
index for a long time. It may be picked by some other thread,
that runs ifnet_byindex_ref(), who takes the ifnet from index,
and bumps refcount. When reader drops the lock, if_free_internal()
proceeds with free. Then reader tries to free it a second time.
boundaries. For good measure, align all other objects to cache
lines boundaries.
Use the new arch_loadseg I/F to keep track of kernel text and
data so that we can wire as much of it as is possible. It is
the responsibility of the kernel to link critical (read IVT
related) code and data at the front of the respective segment
so that it's covered by TRs before the kernel has a chance to
add more translations.
Use a better way of determining whether we're loading a legacy
kernel or not. We can't check for the presence of the PBVM page
table, because we may have unloaded that kernel and loaded an
older (legacy) kernel after that. Simply use the latest load
address for it.
1. arch_loadaddr - used by platform code to adjust the address at which
the object gets loaded. Implement PC98 using this new interface instead
of using conditional compilation. For ELF objects the ELF header is
passed as the data pointer. For raw files it's the filename. Note that
ELF objects are first considered as raw files.
2. arch_loadseg - used by platform code to keep track of actual segments,
so that (instruction) caches can be flushed or translations can be
created. Both the ELF header as well as the program header are passed
to allow platform code to treat the kernel proper differently from any
additional modules and to have all the relevant details of the loaded
segment (e.g. protection).
- Add more fields for USB device and host mode
- Add more information to USB PF header so that decoding
can easily be done by software analyzer tools like
Wireshark.
- Optimise usbdump to display USB streams in text format
more efficiently.
- Software using USB PF must be recompiled after
this commit, due to structure changes.
MFC after: 7 days
Approved by: thompsa (mentor)
bio_children > 1, g_destroy_bio() is never called and the bio
leaks. Fix this by calling g_destroy_bio() earlier, before the check.
Submitted by: Victor Balada Diaz <victor@bsdes.net> (initial version)
Approved by: pjd (mentor)
MFC after: 1 week
This is a MIPS4KC CPU with various embedded peripherals, including
wireless and ethernet support.
This commit includes the platform, UART, ethernet MAC and GPIO support.
The interrupt-driven GPIO code is disabled for now pending GPIO changes
from the submitter.
Submitted by: Aleksandr Rybalko <ray@dlink.ua>
environments into the kernel environment.
The eventual aim is to replace these with specific drivers for
the various bootloaders (redboot, uboot, etc.) This however will
work for the time being until it can be properly addressed.
Submitted by: Aleksandr Rybalko <ray@dlink.ua>
- In softdep_revert_mkdir() find the dotaddref before we attempt to cancel
the jaddref so we can make assumptions about where the dotaddref is on
the list. cancel_jaddref() does not always remove items from the list
anymore.
- Always set GOINGAWAY on an inode in softdep_freefile() if DEPCOMPLETE
was never set. This ensures that dependencies will continue to be
processed on the inowait/bufwait list and is more an artifact of
the structure of the code than a pure ordering problem.
- Always set DEPCOMPLETE on canceled jaddrefs so that they can be freed
appropriately. This normally occurs when the refs are added to the
journal but if they are canceled before this point the state would
never be set and the dependency could never be freed.
Reported by: pho
Tested by: pho
There is a generic problem with the shims for ioctls that receive
pointers to the usermode data areas in the data argument. We either have
to modify the handler to accept UIO_USERSPACE/UIO_SYSSPACE indicator, or
allocate and fill a usermode memory for data buffer in the host format.
The change goes the second route, in particular because we do not need
to modify the handler.
Submitted by: John Wehle <john feith com>
MFC after: 2 weeks
g_io_deliver(). In such case it increases 'pace' counter on each ENOMEM and
reschedules the request. The 'pace' counter is decreased for each request going
down, but until 'pace' is greater than zero, GEOM will handle at most 10
requests per second. For GEOM GATE users that are proxy to local GEOM providers
(like ggatel(8) and HAST) we can end up with almost permanent slow down of GEOM
down queue. This is because once we reach GEOM GATE queue limit, we return
ENOMEM to the GEOM. This means that we have, eg. 1024 I/O requests in the GEOM
GATE queue. To make room in the queue and stop returning ENOMEM we need to
proceed the requests of course, but those requests are handled by userland
daemons that handle them by reading/writing also from/to local GEOM providers.
For example with HAST, a new requests comes to /dev/hast/data, which is GEOM
GATE provider. GEOM GATE passes the request to hastd(8) and hastd(8)
reads/writes from/to /dev/da0. Once we reach GEOM GATE queue limit, to free up
a slot in GEOM GATE queue, hastd(8) has to read/write from/to /dev/da0, but
this request will also be very slow, because GEOM now slows down all the
requests. We end up with full queue that we can unload at the speed of 10
requests per second. This simply looks like a deadlock.
Fix it by allowing userland daemons that work with both GEOM GATE and local
GEOM providers to specify unlimited queue size, so GEOM GATE will never return
ENOMEM to the GEOM.
MFC after: 1 week
offset in the flash.
Some devices (eg the TPLink WR-1043ND) don't have a flash environment
partition which can be queried for the current board settings.
This particular workaround allows for image creators to use a hint
to set the base MAC address. For example:
hint.arge.0.eeprommac=0x1f01fc00
get's defragged due to a mapping failure the header
pointers will be invalidated and can result in a
TSO or other failure down the line. So, when the
remapping occurs force a retry thru the offload
calculation code. Thanks to Andrew Boyer for discovering
this and cooking up the fix!!
to calculate the outstanding descriptors that need to be
refreshed at any time, and use THAT in rxeof to determine
if refreshing needs to be done. Also change the local_timer
to simply fire off the appropriate interrupt rather than
schedule a tasklet, its simpler.
MFC in two weeks
In particular:
- implement compat shims for old stat(2) variants and ogetdirentries(2);
- implement delivery of signals with ancient stack frame layout and
corresponding sigreturn(2);
- implement old getpagesize(2);
- provide a user-mode trampoline and LDT call gate for lcall $7,$0;
- port a.out image activator and connect it to the build as a module
on amd64.
The changes are hidden under COMPAT_43.
MFC after: 1 month
leads to compile errors when trying to compile firmware(9) stubs created with
gawk, as multiple #include statements end up on the same line. Replace the
multi-line printc statement that outputs all of the #includes with one printc
per #include. This allows modules compatible with firmware(9) to be cross-built
from a Linux machine without requiring the one true awk to be installed.
I've intentionally done the minimal set of changes necessary to make gawk
produce valid (but not pretty) C code, to reduce the churn and keep fw_stubs.awk
as readable as possible.
Approved by: emaste (mentor)
MFC after: 2 weeks
- Remove contention on ISR during the crypto operation by using rwlock(9).
- Remove a second lookup of the SA in the callback.
Gain on 6 cores CPU with SHA1/AES128 can be up to 30%.
Reviewed by: vanhu
MFC after: 1 month
too much time. This can finish in a scheduler deadlock with ping-pong
between two threads.
One sample of this is:
- device lapic (to have a preemption point on critical_exit())
- options DEVICE_POLLING with HZ>1499 (to have lapic freq = hardclock freq)
- running a cpu intensive task (that does not enter the kernel)
- only one CPU on SMP or no SMP.
As requested by jhb@ 4BSD have received the same type of fix instead of
propagating the flag to the new thread.
Reviewed by: jhb, jeff
MFC after: 1 month
bus driver will now remember the size of a BAR obtained during the initial
bus scan and use that size when doing lazy resource allocation rather than
resizing the BAR. The bus driver will now also report unallocated BARs to
userland for display by 'pciconf -lb'. Psuedo-resources that are not BARs
(such as the implicit I/O port resources for master/slave ATA controllers)
will no longer be listed as BARs in 'pciconf -lb'. During resume, BARs are
restored from their new saved state instead of having the raw registers
saved and restored across resume. This also fixes restoring BARs at
unusual loactions if said BAR has been allocated by a driver.
Add a constant for the offset of the ROM BIOS BAR in PCI-PCI bridges and
properly handle ROM BIOS BARs in PCI-PCI bridges. The PCI bus now also
properly handles the lack of a ROM BIOS BAR in a PCI-Cardbus bridge.
Tested by: jkim
- AH does not release the SA like in ESP/IPCOMP when handling EAGAIN
- ipsec_process_done incorrectly release the SA.
Reviewed by: vanhu
MFC after: 1 week
I have not properly thought through the commit. After r220031 (linux
compat: improve and fix sendmsg/recvmsg compatibility) the basic
handling for SO_PASSCRED is not sufficient as it breaks recvmsg
functionality for SCM_CREDS messages because now we would need to handle
sockcred data in addition to cmsgcred. And that is not implemented yet.
Pointyhat to: avg
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
on the set of rules it maintains and the current resource usage. It also
privides userland API to manage that ruleset.
Sponsored by: The FreeBSD Foundation
Reviewed by: kib (earlier version)
to the maximum allowed window. Growing the window too large would cause
an underflow in the calculations in tcp_output() to decide if a window
update should be sent which would prevent the persist timer from being
started if data was pending and the other end of the connection advertised
an initial window size of 0.
PR: kern/154006
Submitted by: Stefan `Sec` Zehl sec 42 org
Reviewed by: bz
MFC after: 1 week
bit fileid's in NFSv2 and NFSv3. Without this fix, invalid casting (and sign
extension) was creating problems for any fileid greater than 2^31.
We discovered this because we have test clusters with more than 2 billion
allocated files and 64-bit ino_t's (and friend structures).
Reviewed by: rmacklem
Approved by: zml (mentor)
MFC after: 2 weeks
the iommu(4) provided one, i.e. in case of Hummingbird and Sabre bridges,
otherwise just use the iommu(4) one. This also fixes a bug introduced in
r220039 which caused an empty DMA method table to be used for the second
of a pair of Psycho bridges.
and per-loginclass resource accounting information, to be used by the new
resource limits code. It's connected to the build, but the code that
actually calls the new functions will come later.
Sponsored by: The FreeBSD Foundation
Reviewed by: kib (earlier version)
in the RX path when doing 11n and block-ack'ed frames. Apparently, the MAC
will loop over that self-linked descriptor and treat it as "good enough"
for (incorrectly!) ACKing the frames in the block-ack.
Until I figure out how to work around this issue in the future, this counter
will tell me if packet RX processing ever gets to the point where it's
touching the self-linked descriptor. If there's ever enough packets to get
to that point, BA's will be invalid and likely very unhappy.
listing each card as it is found on non-PC98 (PC98 already had this).
- Increase the length of the DELAY() used before timing out while reading
PNP resource data.
Tested by: Steven Nikkel steven_nikkel ertyu org
MFC after: 1 week
of active DMA cycle. dc_setcfg() also has to wait until the DMA
engine is stopped so using a common function to handle the job is
better than duplicating the code.
No objection from: marius
makes controller to receive bad frames and i82557 will also receive
bad frames since fxp(4) have to receive VLAN oversized frames. If
fxp(4) encounter DMA overrun error, the received frame size would
be 0 so the actual frame size after checksum field extraction the
length would be negative(-2). Due to signed/unsigned comparison
used in driver, frame length check did not work for DMA overrun
frames. Correct this by casting it to int.
While I'm here explicitly check DMA overrun error and discard the
frame regardless of result of received frame length check.
Reported by: n_hibma
Tested by: n_hibma
MFC after: 1 week
I'll clear how it's supposed to work with Bernhard and then look
at enabling this in the correct situations.
But this -does- enable HT RTS protection (using the appropriate legacy
rates) if this bit of code is enabled.
instead of 0x100000. As a side effect, an amd64 kernel now loads at
physical address 0x200000 instead of 0x100000. This is probably for the
best because it avoids the use of a 2MB page mapping for the first 1MB of
the kernel that also spans the fixed MTRRs. However, getmemsize() still
thinks that the kernel loads at 0x100000, and so the physical memory between
0x100000 and 0x200000 is lost. Fix this problem by replacing the hard-wired
constant in getmemsize() by a symbol "kernphys" that is defined by the
linker script.
In collaboration with: kib
registered in g_gate_units array and when its sc_provider field is
filled. If during this period g_gate_units is accessed by another
thread that is checking for provider name collision the crash is
possible.
Fix this by adding sc_name field to struct g_gate_softc. In
g_gate_create() when g_gate_softc is created but sc_provider is still
not sc_name points to provider name stored in the local array.
Approved by: pjd (mentor)
Reported by: Freddie Cash <fjwcash@gmail.com>
MFC after: 1 week
just for Redboot.
At some point we're going to need to build options for different
boot environments - for example, the UBoot setups I've seen simply
have the MAC address hard-coded at a fixed location in flash.
The OpenWRT support simply yanks the if_arge MAC directly from that
in code, rather than trying to find a uboot environment to pull it
from.
memory detected from Redboot, or overrides the "otherwise" case
if no Redboot information was found.
Some AR71XX platforms don't use Redboot (eg TP-LINK devices using
UBoot; some later Ubiquiti devices which apparently also use
UBoot) and at least one plain out lies - the Ubiquiti LS-SR71A
Redboot says there's 16mb of RAM when in fact there's 32mb.
A more "clean" solution will be needed at a later date.
The AR913x/AR724x USB lives at a different offset to the AR71xx
USB, so this needs to be either adjusted for in a subsequent
commit, or updated in hints for kernels compiled for those
platforms.
Submitted by: Luiz Otavio O Souzau <loos.br@gmail.com>
syncing for Hummingbird and Sabre bridges should be applied with every
BUS_DMASYNC_POSTREAD instead of in a wrapper around interrupt handlers
for devices behind PCI-PCI bridges only as suggested by the documentation
(code for the latter actually exists in OpenSolaris but is disabled by
default), which also makes more sense.
- Take advantage of the ofw_pci_setup_device method introduced in r220038
for disabling bus parking for certain EBus bridges in order to
- Mark some unused parameters as such.
register changes when compiled with SCHIZO_DEBUG and take advantage
of them.
- Add support for the XMITS Fireplane/Safari to PCI-X bridges. I tought
I'd need this for a Sun Fire 3800, which then turned out to not being
equipped with such a bridge though. The support for these should be
complete but given that it hasn't actually been tested probing is
disabled for now.
This required a way to alter the XMITS configuration in case a PCI-X
device is found further down the device tree so the sparc64 specific
ofw_pci kobj was revived with a ofw_pci_setup_device method, which is
called by the ofw_pcibus code for every device added.
- A closer inspection of the OpenSolaris code indicates that consistent
DMA flushing/syncing as well as the block store workaround should be
applied with every BUS_DMASYNC_POSTREAD instead of in a wrapper around
interrupt handlers for devices behind PCI-PCI bridges only as suggested
by the documentation (code for the latter actually exists in OpenSolaris
but is disabled by default), which also makes more sense.
- Add a workaround for Casinni/Skyhawk combinations. Chances are that
this solves the crashes seen when using the the on-board Casinni NICs
of Sun Fire V480 equipped with centerplanes other than 501-6780 or
501-6790. This also takes advantage of the ofw_pci_setup_device method.
- Mark some unused parameters as such.
This seems to have been a part of a bigger patch by dchagin that either
haven't been committed or committed partially.
Submitted by: dchagin, nox
MFC after: 2 weeks
- implement baseic stubs for capget, capset, prctl PR_GET_KEEPCAPS
and prctl PR_SET_KEEPCAPS.
- add SCM_CREDS support to sendmsg and recvmsg
- modify sendmsg to ignore control messages if not using UNIX
domain sockets
This should allow linux pulse audio daemon and client work on FreeBSD
and interoperate with native counter-parts modulo the differences in
pulseaudio versions.
PR: kern/149168
Submitted by: John Wehle <john@feith.com>
Reviewed by: netchild
MFC after: 2 weeks
And drop dummy definitions for those system calls.
This may transiently break the build.
PR: kern/149168
Submitted by: John Wehle <john@feith.com>
Reviewed by: netchild
MFC after: 2 weeks
by default.
Adventourous souls with an AR9220/AR9280 or later and who have a device
that sends PS-POLL frames may wish to try tinkering with this option and
get back to me.
Linux ath9k only enables this for AR9280 and later NICs; so
create a capability for it so it isn't enabled for earlier
NICs.
Enabling hardware PS-POLL support will come in a later commit
and will be disabled by default.
Since signal trampolines are copied to the shared page do not need to
leave place on the stack for it. Forgotten in the previous commit.
MFC after: 1 Week
Even though they map to setting the error filter register,
ath9k also writes them untouched to AR_RX_FILTER.
The Force-BSSID match bit can stay high, as it maps to a
misc mode register setting rather than an RX filter bit.
The phyerr, radar and bssid-match bits aren't real bits, they map
to enabling bits in other registers. Move those out of the way of
valid RX filter bits.
Add a few new fields from ath9k - compba, ps-poll, mcast-bcast-all.
CPUs. These CPUs need explicit MSR configuration to expose ceratin CPU
capabilities (e.g., CMPXCHG8B) to work around compatibility issues with
ancient software. Unfortunately, Rise mP6 does not set the CX8 bit in CPUID
and there is no MSR to expose the feature although all mP6 processors are
capable of CMPXCHG8B according to datasheets I found from the Net. Clean up
and simplify VIA PadLock detection while I am in the neighborhood.
root directory of msdosfs mount. The VFS code would handle deletion
case itself too, assuming VV_ROOT flag is not lost. The msdosfs_rename()
should also note attempt to rename root via doscheckpath() or different
mount point check leading to EXDEV. Nonetheless, keep the checks for now.
The change is inspired by NetBSD change referenced in PR, but return
EBUSY like kern_unlinkat() does.
PR: kern/152079
MFC after: 1 week
Changes since 7.8.0 (from the official changelog):
- Fixed sporadic interrupt generation for associated CQ when processing
a local invalidate work request
- Changes to core scheduling to avoid starving requests from the host
under heavy RDMA Read Request load (e.g. packets to the wire)
- Programmed the tp tx resource limiter in function of the traffic (only
affects iWarp)
- Increased the egress NIC gather list length from 36 to 46 entries
MFC after: 1 week
If supplied length is zero, and user address is invalid, function
might return -1, due to the truncation and rounding of the address.
The callers interpret the situation as EFAULT. Instead of handling
the zero length in caller, filter it in vm_fault_quick_hold_pages().
Sponsored by: The FreeBSD Foundation
Reviewed by: alc
The new function fallocf(9), that is renamed falloc(9) with added
flag argument, is provided to facilitate the merge to stable branch.
Reviewed by: jhb
MFC after: 1 week
Code inspection shows freebsd32_ioctl calls fget for a fd and calls
a subroutine to handle each specific ioctl. It is expected that the
subroutine will call fdrop when done. However many of the subroutines
will exit out early if copyin encounters an error resulting in fdrop
never being called.
Submitted by: John Wehle <john feith com>
MFC after: 3 days
the channel width is ni->ni_chw, which is set to the negotiated channel
width. ni->ni_htflags is the capability, rather than the negotiated
value.
Teach both the TX path and the sample rate module about this.
This seems to work fine for STA but not HT/20 AP mode.
Further discussion with net80211 people will need to take place
to ensure that the right flags are set based on the negotiated
capabilities of the remote peer, rather than whatever the local
parameters are.
Sending short-gi frames in 20mhz may work on some chips but
it certainly isn't supported on anything currently supported
by the HAL; and sending HT40 frames in HT20 mode just plain
won't work.
settings, it seems that our defines are backwards and don't match what
is in the EEPROM documentation or internal driver.
The ath9k code used to have a bitfield here, rather than a uint8_t, and
there were #defines used to swap the order based on the endian of the
platform - this wasn't because of nybble or bit ordering of the
underlying host but because of what the compiler was doing.
This may be the reason for the backwards field numbers, as ath9k had
similar issues.
the AR9285 so I'll leave it off for that.
Ath9k sources indiciate that one of the ANI modes interferes with
RIFS detection, so match ath9k and disable that.
* The existing interrupt mitigation code didn't mitigate anything - the
per-packet TX/RX interrupts are still occuring. It's possible this
worked for the AR5416 but not any later chipsets; I'll investigate and
update as needed.
* Set both the RX and TX threshold registers whilst I'm at it.
This is verified to work on the AR9220 and AR9160. I'm leaving it off
by default in case it's truely broken, but I need to have it enabled
when doing 11n testing or interrupt loads exceed 10,000 interrupts/sec.
Add new RAID GEOM class, that is going to replace ataraid(4) in supporting
various BIOS-based software RAIDs. Unlike ataraid(4) this implementation
does not depend on legacy ata(4) subsystem and can be used with any disk
drivers, including new CAM-based ones (ahci(4), siis(4), mvs(4), ata(4)
with `options ATA_CAM`). To make code more readable and extensible, this
implementation follows modular design, including core part and two sets
of modules, implementing support for different metadata formats and RAID
levels.
Support for such popular metadata formats is now implemented:
Intel, JMicron, NVIDIA, Promise (also used by AMD/ATI) and SiliconImage.
Such RAID levels are now supported:
RAID0, RAID1, RAID1E, RAID10, SINGLE, CONCAT.
For any all of these RAID levels and metadata formats this class supports
full cycle of volume operations: reading, writing, creation, deletion,
disk removal and insertion, rebuilding, dirty shutdown detection
and resynchronization, bad sector recovery, faulty disks tracking,
hot-spare disks. For Intel and Promise formats there is support multiple
volumes per disk set.
Look graid(8) manual page for additional details.
Co-authored by: imp
Sponsored by: Cisco Systems, Inc. and iXsystems, Inc.
VFS where we know if this is truncate(2) or ftruncate(2). If this is the
latter we should depend on the mode the file was opened and not on the current
permission.
PR: standards/154873
Reported by: Mark Martinec <Mark.Martinec@ijs.si>
Discussed with: Eric Schrock <eric.schrock@delphix.com>
Discussed with: Mark Maybee <Mark.Maybee@Oracle.COM>
MFC after: 1 month
Introduce new type of BIO_GETATTR -- GEOM::setstate, used to inform lower
GEOM about state of it's providers from the point of upper layers.
Make geom_disk use led(4) subsystem to illuminate states in such fashion:
FAILED - "1" (on), REBUILD - "f5" (slow blink), RESYNC - "f1" (fast blink),
ACTIVE - "0" (off).
LED name should be set for each disk via kern.geom.disk.%s.led sysctl.
Later disk API could be extended to allow disk driver to report this info
in custom way via it's own facilities.
- Hold the proc lock while changing the state from PRS_NEW to PRS_NORMAL
in fork to honor the locking requirements. While here, expand the scope
of the PROC_LOCK() on the new process (p2) to avoid some LORs. Previously
the code was locking the new child process (p2) after it had locked the
parent process (p1). However, when locking two processes, the safe order
is to lock the child first, then the parent.
- Fix various places that were checking p_state against PRS_NEW without
having the process locked to use PROC_LOCK(). Every place was already
locking the process, just after the PRS_NEW check.
- Remove or reduce the use of PROC_SLOCK() for places that were checking
p_state against PRS_NEW. The PROC_LOCK() alone is sufficient for reading
the current state.
- Reorder fill_kinfo_proc() slightly so it only acquires PROC_SLOCK() once.
MFC after: 1 week
The symptom: sometimes 11n (and non-11n) throughput is great.
Sometimes it isn't. Much teeth gnashing occured, and much kernel
bisecting happened, until someone figured out it was the order
of which things were rebooted, not the kernel versions.
(Which was great news to me, it meant that I hadn't broken if_ath.)
What we found was that sometimes the WME parameters for the best-effort
queue had a burst window ("txop") in which the station would be allowed
to TX as many packets as it could fit inside that particular burst
window. This improved throughput.
After initially thinking it was a bug - the WME parameters for the
best-effort queue -should- have a txop of 0, Bernard and I discovered
"aggressive mode" in net80211 - where the WME BE queue parameters
are changed if there's not a lot of high priority traffic going on.
The WME parameters announced in the association response and beacon
frames just "change" based on what the current traffic levels are.
So in fact yes, the STA was acutally supposed to be doing this higher
throughput stuff as it's just meant to be configuring things based on
the WME parameters - but it wasn't.
What was eventually happening was this:
* at startup, the wme qosinfo count field would be 0;
* it'd be parsed in ieee80211_parse_wmeparams();
* and it would be bumped (to say 10);
* .. and the WME queue parameters would be correctly parsed and set.
But then, when you restarted the assocation (eg hostap goes away and
comes back with the same qosinfo count field of 10, or if you
destroy the sta VIF and re-create it), the WME qosinfo count field -
which is associated not to the VIF, but to the main interface -
wouldn't be cleared, so the queue default parameters would be used
(which include no burst setting for the BE queue) and would remain
that way until the hostap qosinfo count field changed, or the STA
was actually rebooted.
This fix simply cleares the wme capability field (which has the count
field) to 0, forcing it to be reset by the next received beacon.
Thanks go to Milu for finding it and helping me track down what was
going on, and Bernard Schmidt for working through the net80211 and
WME specific magic.
Change BIO_GETATTR("GEOM::kerneldump") API to make set_dumper() called by
consumer (geom_dev) instead of provider (geom_disk). This allows any geom
insert it's code into the dump call chain, implementing more sophisticated
functionality then just disk partitioning.
queue has its own interrupt. If the exact number that we need is not a
power of 2 and we're using MSI, then switch to interrupt multiplexing.
While here, replace the magic numbers with something more readable.
MFC after: 3 days
At least one AR5416 user has reported measurable throughput drops
with this option. For now, disable it and make it a run-time
twiddle. It won't take affect until the next radio programming
trip though (eg channel scan, channel change.)
vfs_equalopts(). This allows vfs_sanitizeopts() to filter redundant
occurrences of these options. It was possible that for example both "ro"
and "rw" options became active concurrently.
PR: kern/133614
Discussed on: freebsd-hackers
MFC after: 1 month
Also, express this new maximum as a fraction of the kernel's address
space size rather than a constant so that increasing KVA_PAGES will
automatically increase this maximum. As a side-effect of this change,
kern.maxvnodes will automatically increase by a proportional amount.
While I'm here ensure that this change doesn't result in an unintended
increase in maxpipekva on i386. Calculate maxpipekva based upon the
size of the kernel address space and the amount of physical memory
instead of the size of the kmem map. The memory backing pipes is not
allocated from the kmem map. It is allocated from its own submap of
the kernel map. In short, it has no real connection to the kmem map.
(In fact, the commit messages for the maxpipekva auto-sizing talk
about using the kernel map size, cf. r117325 and r117391, even though
the implementation actually used the kmem map size.) Although the
calculation is now done differently, the resulting value for
maxpipekva should remain almost the same on i386. However, on amd64,
the value will be reduced by 2/3. This is intentional. The recent
change to VM_KMEM_SIZE_SCALE on amd64 for the benefit of ZFS also had
the unnecessary side-effect of increasing maxpipekva. This change is
effectively restoring maxpipekva on amd64 to its prior value.
Eliminate init_param3() since it is no longer used.
so there's no need to enable the RX of invalid frames just to do ANI.
The if_ath code and AR5212 ANI code setup the RX filter bits to enable
receiving OFDM/CCK errors if the device doesn't have the hardware
MIB counters. It isn't initialising it for the AR5416+ because all of
those chips have hardware MIB counters.
This fixes the odd (and performance affecting!) situation where if ani
is enabled (via sysctl dev.ath.X.intmit) then suddenly there's be a very
large volume of phy errors - which is good to track, but not what was
intended. Since each PHY error is a received (0 length) frame, it can
significantly tie up the RX side of things.
It's still not ready for prime-time - there's some TX niggles with these 11n
cards that I'm still trying to wrap my head around, and AMPDU-TX is just not
implemented so things will come to a crashing halt if you're not careful.
"extended capabilities" to refer to the new set of capability structures
starting at offset 0x100 in config space for PCI-express devices. For now
both function names will still work. I will merge this to older branches
to ease driver portability, but 9.0 will ship with a new pci_find_extcap()
function that locates extended capabilities instead.
Reviewed by: imp
MFC after: 1 week
This fix modifies the const addac initval array, rather than modifying
a local copy. It means that running >1 AR9160 on a board may prove to
be unpredictable.
The AR5416 init path also does something similar, so supporting
>1 AR5416 of different revisions could cause problems.
The later fix will be to create a private copy of the Addac data
for the AR5416, AR9160 (and AR9100 when it's merged in) and then
modify that as needed.
Obtained From: Linux ath9k
I found this when trying to figure out why the RX PHY error count
didn't match the OFDM error count ANI was using. It turns out
there was two problems:
* What this commit addresses - using the wrong mask for OFDM errors,
and
* The RX filter is set incorrectly after a channel scan (at least)
even if interference mitigation is enabled by default.
ANI is still disabled by default for the AR5416 and later chips.
set as TCP.
- Eliminate the fully linear non-scatter/gather rx path, there is no
harm in using arrays of clusters for both TCP and UDP.
- Implement support for enabling/disabling per-vlan priority pause and
queues via sysctl.
bring it in line with the rest of the register initialisation.
I've verified that the 2/5ghz board values written to the
chip match what was previously written.
* add pspoll/uapsd queue setup defaults;
* enable the exponential backoff window rather than the random
backoff window when doing TX contention management.
would be a problem, make sure it isn't overwritten by whatever is in
there at cold reset.
This brings the > ar5416 init path treatment of AR_MISC_MODE.
report descriptor information, sysctl utility
will show it for us.
- Modify sysctl node description to make it more
understanable.
Found by: Alexander Best <arundel@freebsd.org>
Submitted by: Eygene Ryabinkin <rea@freebsd.org>
MFC after: 14 days
Approved by: thompsa (mentor)
value is updated after that we read it in the queue-head. This patch can
fix problems with BULK timeouts. The issue was found on a Nvidia chipset.
MFC after: 14 days
Approved by: thompsa (mentor)
services or PAL procedures. The new implementation is based on
specific functions that are known to be called in certain scenarios
only. This in particular fixes the PAL call to obtain information
about translation registers. In general, the new implementation does
not bank on virtual addresses being direct-mapped and will work when
the kernel uses PBVM.
When new scenarios need to be supported, new functions are added if
the existing functions cannot be changed to handle the new scenario.
If a single generic implementation is possible, it will become clear
in due time.
While here, change bootinfo to a pointer type in anticipation of
future development.
from another context at the moment of later access.
PR: kern/155555
Submitted by: Andrew Boyer <aboyer att averesystems.com>
Approved by: avg (mentor)
MFC after: 2 weeks
the topology mutex in the following functions, that manipulate pointers
to peer nodes:
- ng_bypass()
- ng_path2noderef() when switching to the next node in sequence.
Rewrite the function a bit.
- ng_address_hook()
- ng_address_path()
This patch improves stability of large mpd5 installations.
* Pull out the static rix stuff into a different function
* I know this may slightly drop performance, but check if a static
rix is needed before each packet TX.
* Whilst I'm at it, add a little extra debugging to the rate
control stuff to make it easier to follow what's going on.
1. The PBVM is in region 4, so if we want to make use of it, we
need region 4 freed up.
2. Region 4 and above cannot be represented by an off_t by virtue
of that type being signed. This is problematic for truss(1),
ktrace(1) and other such programs.
Give it a good go (32 attempts) and then print out a warning that's
going to occur whether HAL debugging is enabled or not. Then don't
abort the radio setup; just continue merrily along.
This should fix the issue that users were having where scanning would
occasionally fail on the active channel, causing traffic to cease
until the radio scanned again.
since before r127501. Strictly speaking, the buffer pages are not
"wired". They remain in the paging queues. However, they are pinned in
memory using vm_page_hold().
not needed.
These calibrations are only applicable if the chip operating mode
engages both interleaved RX ADCs (ie, it's compensating for the
differences in DC gain and DC offset -between- the two ADCs.)
Otherwise the chip reads values of 0x0 for the secondary ADC
(as I guess it's not enabled here) and thus writes potentially
bogus info into the chip.
I've tested this on the AR9160 and AR9280; both behave themselves
in 11g mode with these calibrations disabled.
for fixing them based on the ath9k related TXQ fixes.
I've done this so people can go over the history of the diffs to the original
AR5212 routines (which AR5416 and later chips use) to see what's changed.
enables broadcast filtering. Make sure to clear the bit to receive
broadcast frames. While I'm here rename the bit definition to
reflect reality.
Reported by: brad@OpenBSD
MFC after: 1 week
- A closer inspection of the OpenSolaris code indicates the block store
workaround is only necessary in case of BUS_DMASYNC_POSTREAD.
- Mark some unused parameters as such.
In some cases as udp6_connect() without an earlier bind(2) to an
address, v4-mapped scokets allowed and a non mapped destination
address, we can end up here with both v4 and v6 indicated:
inp_vflag = (INP_IPV4|INP_IPV6|INP_IPV6PROTO)
In that case however laddrp is NULL as the IPv6 path does not
pass in a copy currently.
Reported by: Pawel Worach (pawel.worach gmail.com)
Tested by: Pawel Worach (pawel.worach gmail.com)
MFC after: 6 days
X-MFC with: r219579
configurations and make it opt-in for those who want it. LINT will
still build it.
While it may be a perfect win in some scenarios, it still troubles users
(see PRs) in general cases. In addition we are still allocating resources
even if disabled by sysctl and still leak arp/nd6 entries in case of
interface destruction.
Discussed with: qingli (2010-11-24, just never executed)
Discussed with: juli (OCTEON1)
PR: kern/148018, kern/155604, kern/144917, kern/146792
MFC after: 2 weeks
This commit really is "fix the OFDM duration calculation to match reality when
running in 802.11g mode."
The AR5212 init vals set AR_MISC_MODE to 0x0 and all the bits that can be set are
set through code.
The AR5416 and later initvals set AR_MISC_MODE to various other values (with
the AR5212 AR_MISC_MODE options cleared), which include AR_PCU_CCK_SIFS_MODE .
This adds 6uS to SIFS on non-CCK frames when transmitting.
This fixes the issue where _DATA_ 802.11g OFDM frames were being TX'ed with
the ACK duration set to 38uS, not 44uS as on the AR5212 (and other devices.)
The AR5212 TX pathway obeys the software-programmed duration field in the packet,
but the 11n TX pathway overrides that with a hardware-calculated duration. This
was getting it wrong because of the above AR_MISC_MODE setting. I've verified
that 11g data OFDM frames are now being TXed with the correct ACK+SIFS duration
programmed in.
Since ath9k does some slightly different bit fiddling when setting up
the TX queues, it may that the TX queue setup/reset functions will need
overriding later on.
segment so that it's always mapped by the loader.
o Change the alternate fault handlers to account for PBVM. Since
currently the region is handled by the VHPT, no alternate faults
will be generated for it.
been undergoing test for some weeks. This improves the RX
mbuf handling to avoid system hang due to depletion. Thanks
to all those who have been testing the code, and to Beezar
Liu for the design changes.
Next the igb driver is updated for similar RX changes, but
also to add new features support for our upcoming i350 family
of adapters.
MFC after a week
chipsets that do not have an HT slave at 0:0:0:0. The Linux quirk is
actually specific to Nvidia chipsets and the check I had added was in
the wrong place.
Prodded by: nathanw
- Always enable the HyperTransport MSI mapping window for HyperTransport
to PCI bridges (these show up as HyperTransport slave devices).
The mapping windows in PCI-PCI bridges are enabled by existing code
in the PCI-PCI bridge driver as MSI requests propagate up the device
tree, but Host-PCI bridges don't really show up in that tree.
- If the PCI device at domain 0 bus 0 slot 0 function 0 is not a
HyperTransport device, then blacklist MSI on any other HT devices in
the system. Linux has a similar quirk.
PR: kern/155442
Tested by: Zack Dannar zdannar of gmail
MFC after: 1 week
which are not yet fully initialized (i.e. ones with p_state == PRS_NEW).
Without it, we could panic in _thread_lock_flags().
Note that there may be other instances of FOREACH_PROC_IN_SYSTEM() that
require similar fix.
Reported by: pho, keramida
Discussed with: kib
ffs_snapgone(). ufs.ko module is not build with FFS define, causing
snapshot inode number slots in superblock never be freed, as well as a
reference on the snapshot vnode.
IFS was removed several years ago, and UFS/FFS separation was not
maintained for real.
Reported, analyzed and tested by: Yamagi Burmeister <lists yamagi org>
MFC after: 3 days
With this change, driver may not notice updated descriptor status
change when bounce buffers are active. However, rxeof() in next run
will handle the synchronization.
Change dc_rxeof() a bit to return the number of processed frames in
RX descriptor ring. Previously it returned the number of frames
that were successfully passed to upper stack which in turn means it
ignored frames that were discarded due to errors. The number of
processed frames in RX descriptor ring is used to detect whether
driver is out of sync with controller's current descriptor pointer.
Returning number of processed frames reduces unnecessary (probably
wrong) re-synchronization.
Reviewed by: marius
Unfortunately, it pulls in <machine/cputypes.h> but it is small enough and
namespace pollution is minimal, I hope.
Pointed out by: bde
Pointy hat: jkim
Add support for Pre-Boot Virtual Memory (PBVM) to the loader.
PBVM allows us to link the kernel at a fixed virtual address without
having to make any assumptions about the physical memory layout. On
the SGI Altix 350 for example, there's no usuable physical memory
below 192GB. Also, the PBVM allows us to control better where we're
going to physically load the kernel and its modules so that we can
make sure we load the kernel in memory that's close to the BSP.
The PBVM is managed by a simple page table. The minimum size of the
page table is 4KB (EFI page size) and the maximum is currently set
to 1MB. A page in the PBVM is 64KB, as that's the maximum alignment
one can specify in a linker script. The bottom line is that PBVM is
between 64KB and 8GB in size.
The loader maps the PBVM page table at a fixed virtual address and
using a single translations. The PBVM itself is also mapped using a
single translation for a maximum of 32MB.
While here, increase the heap in the EFI loader from 512KB to 2MB
and set the stage for supporting relocatable modules.
The compiler will truncate the 32-bit return value of mv_gpio_value_get()
to match the 8-bit return value of mv_gpio_in(). A conditional expression
is used to have mv_gpio_in() always return 0 or 1 instead.
soon as possible for stack protector. However, dummy timecounter does not
have enough entropy and we don't need to sacrifice Pentium class and later.
Pointed out by: Maxim Dounin (mdounin at mdounin dot ru)
The compiler seems to assume it's a 32-bit integral and rounding to the
page size using the standard expression (((u_long)(x) + mask) & ~mask),
results in a 32-bit value. Dropping the 'U' suffix is enough to have the
compiler treat the expression as a 64-bit integral.
handlers.
o Put the IVT in its own section and keep the supporting code close.
o Make sure the VHPT is sized so that it can be mapped using a single
translation.
o Map the PAL code and VHPT with a translation that has the right size.
Assume the platform has a PAL code size that can be mapped with a
single translations.
o Pass the pointer to the bootinfo structure as an argument to ia64_init().
o Get rid of LOG2_ID_PAGE_SIZE and IA64_ID_PAGE_SIZE. It was used to map
the regions 6 & 7 and was as large as possible. The problem is that we
can't support memory attributes easily if the granuratity is not a page.
We need to support memory attributes because the new USB stack violates
the BUS_DMA(9) interface.
o Update some comments...
NOTE: this is broken for SMP kernels, because the AP startup code hasn't
been updated yet.
can be put right at the front when put in its own section. This makes
sure that when the loader can only map a relatively small part of the
PBVM, the IVT and the startup code is wired.
This does a few things in particular:
* Abstracts out the gain control settings into a separate function;
* Configure antenna diversity, LNA and antenna gain parameters;
* Configure ob/db entries - the later v4k EEPROM modal revisions have
multiple OB/DB parameters which are used for some form of
calibration. Although the radio does have defaults for each,
the EEPROM can override them.
This resolves the AR2427 related issues I've been seeing and makes
it stable at all 11g rates for both TX and RX.
sizes are not supported.
o Map the PBVM page table.
o Map the PBVM using the largest possible power of 2 that is less than
the amount of PBVM used and round down to a valid page size. Note
that the current kernel is between 8MB and 16MB in size, which would
mean that 8MB would be the typical size of the mapping, if only 8MB
wasn't an invalid page size. In practice, we end up mapping the first
4MB of PBVM in most cases.
The offsets didn't match the assumption that nfarray[] is ordered by the
chainmask bits and programmed via the register order in ar5416_cca_regs[].
This repairs that damage and ensures that chain 1 is programmed correctly.
(And extension channels will now be programmed correctly also.)
This fixes some of the stuck beacons I've been seeing on my AR9160/AR5416
setups - because Chain 1 would be programmed -80 or -85 dBm, which is
higher than the actual noise floor and thus convincing the radio that
indeed it can't ever transmit.
uses of ic_curchan occur. Due to the nature of a scan, switching
channels constantly and all this happening without any kind of locks
held, it might happen that ic_curchan points to nowhere leading to
panics. Fix this by not allowing frame injections while in SCAN state.
Tested by: Paul B. Mahol <onemda at gmail.com>
If multiple networks are available the max bandwidth is one
condition used for selecting the "best" BSS. To achieve that
we should consider all parameters which affect the max RX rate.
This includes 20/40MHz, SGI and the of course the MCS set.
If the TX MCS parameters are available we should use those,
because an AP announcing support for receiving frames at 450Mbps
might only be able to transmit at 150Mbps (1T3R). I haven't seen
devices with support for transmitting at higher rates then
receiving, so prefering TX over RX information should be safe.
While here, remove the hardcoded assumption that MCS15 is the max
possible MCS rate, use MCS31 instead which really is the highest
rate (according to the 802.11n std). Also, fix a mismatch of an
40MHz/SGI check.
Contrary to the rateset information in legacy frames the MCS Set
field also contains TX capability information in cases where the
number of available TX and RX spartial streams differ. Because a
rateset doesn't contain that information we have to pull the
those directly from the hardware capabilities.
Get rid of the assumption that every device is capable of 40MHz,
SGI and 2 spartial streams. Instead of printing, in the worst case,
8 times 76 MCS rates, print logically connect ranges and the
support RX/TX streams.
A device without 40MHz and SGI support looks like:
ath0: 2T2R
ath0: 11na MCS 20Mhz
ath0: MCS 0-7: 6.5Mbps - 65Mbps
ath0: MCS 8-15: 13Mbps - 130Mbps
ath0: 11ng MCS 20Mhz
ath0: MCS 0-7: 6.5Mbps - 65Mbps
ath0: MCS 8-15: 13Mbps - 130Mbps
Initialize ic_rxstream/ic_txstream with 2, for compatibility reasons.
Introduce 4 new HTC flags, which are used in addition to ic_rxstream
and ic_txstream to compute the hc_mcsset content and also for initializing
ni_htrates. The number of spatial streams is enough to determine support
for MCS0-31 but not for MCS32-76 as well as some TX parameters in the
hc_mcsset field.
rather than duplicating them for the v14 (ar5416+) and v4k (ar9285) codebases.
Further chipsets (eg the AR9287) have yet another EEPROM format which will use
these routines to calculate things.
to the TX closed-loop power control registers.
* Modify a couple of functions to take the register chain number,
rather than the regChainOffset value. This allows for the
register chain to be logged.
callers. This also fixes a problem when the prison call could set
the inp->in6p_laddr (laddr) and a following priv_check_cred() call
would return an error and will allow us to merge the IPv4 and IPv6
implementation.
MFC after: 2 weeks
even after dropping the reference and unlocking. Previously we
have dereferenced a NULL pointer (after r121765).
Simply unlocking after the block does not work either because of
lock ordering (see r121765) and in addition we would still hold
a pointer to something that might be gone by the time we access it.
Thus take a copy of the value rather than just caching the pointer.
PR: kern/151908
Submitted by: chenyl (netstar2008 126.com) (initial version)
MFC after: 2 weeks
Add systrace_linux32 and systrace_freebsd32 modules which provide
support for tracing compat system calls in addition to native system
call tracing provided by systrace module.
Provided that all the systrace modules are loaded now you can select
what syscalls to trace in the following manner:
syscall::xxx:yyy - work on all system calls that match the specification
syscall:freebsd:xxx:yyy - only native system calls
syscall:linux32:xxx:yyy - linux32 compat system calls
syscall:freebsd32:xxx:yyy - freebsd32 compat system calls on amd64
PR: kern/152822
Submitted by: Artem Belevich <fbsdlist@src.cx>
Reviewed by: jhb (earlier version)
MFC after: 3 weeks
o The bootinfo structure is now a virtual pointer.
o Replace VM_MAX_ADDRESS with VM_MAXUSER_ADDRESS and redefine
VM_MAX_ADDRESS as the maximum address possible (~0UL).
o Since we're not using direct-mapped translations, switching
to physical addressing is less trivial. Reserve the boot stack
for running in physical mode and special-case the EFI call,
as we're still on the boot stack.
o Region 4 belongs to the kernel now, not process space.
also does this for sound drivers it's probably not necessary for all
combinations of controllers and drivers. However, given that our sound
drivers completely lack bus_dmamap_sync(9) calls this at least serves
as a workaround when enabling use of the IOMMU streaming buffers on
sparc64 and generally for arm and mips.
MFC after: 2 weeks
between kernel virtual address and physical address anymore. This so
that we can link the kernel at some virtual address without having
to worry whether the corresponding physical memory exists and is
available. The PBVM uses 64KB pages that are mapped to physical
addresses using a page table. The page table is at least 1 EFI page
in size, but can grow up to 1MB. This effectively gives us a memory
size between 32MB and 8GB -- i.e. enough to load a DVD image if one
wants to.
The loader assigns physical memory based on the EFI memory map and
makes sure that all physical memory is naturally aligned and a power
of 2. At this time there's no consideration for allocating physical
memory that is close to the BSP.
The kernel is informed about the physical address of the page table
and its size and can locate all PBVM pages through it.
The loader does not wire the PBVM page table yet. Instead it wires
all of the PBVM with a single translation. This is fine for now,
but a follow-up commit will fix it. We cannot handle more than 32MB
right now.
Note that the loader will map as much of the loaded kernel and
modules as possible, but it's up to the kernel to handle page faults
for references that aren't mapped. To make that easier, the page
table is mapped at a fixed virtual address.
o Move the backing store in the top half of region 0 now that
region 4 is re-assigned to be part of the kernel.
o De-emphasize VM_MAX_ADDRESS. It's really not used anywhere and probably
means something different than the limit for process address space (we
have VM_MAXUSER_ADDRESS for that).
o Exclude the gateway page from VM_MAXUSER_ADDRESS (i.e. make it the same
as VM_MAX_ADDRESS).
- Emitt an error when encountering an unsupported and in case of the
kernel also for unaligned relocations.
- Fix R_SPARC_LOX10 relocations. Apparently these are hardly ever used.
- Add the _RF_X committed in r212998 also to the tables in the sparc64
reloc.c in order reduce differences between the kernel and the userland
source. This results in no functional change though.
- Fix further inconsistencies in the abbreviations of the names of the
relocations.
- Further whitespace fixes.
Obtained from: NetBSD [1]
This is a minor cosmetic change - the users are more likely to want to
increase (rather than decrease) default kernel stack size,
which is already 4 pages on amd64.
MFC after: 4 days
