alias address needs to be specified.
Add inbound handler to the alias_ftp module. It helps handle active
FTP transfer mode for the case with external clients and FTP server behind
NAT. Fix passive FTP transfer case for server behind NAT using redirect with
external IP address different from NAT ip address.
PR: kern/157957
Submitted by: Alexander V. Chernikov
was used for doing a mount when performing system operations
on AUTH_SYS mounts. This resolved an issue when mounting
a Linux server. Found during testing at the recent
NFSv4 interoperability Bakeathon.
MFC after: 2 weeks
processors unless the invariant TSC bit of CPUID is set. Intel processors
may stop incrementing TSC when DPSLP# pin is asserted, according to Intel
processor manuals, i. e., TSC timecounter is useless if the processor can
enter deep sleep state (C3/C4). This problem was accidentally uncovered by
r222869, which increased timecounter quality of P-state invariant TSC, e.g.,
for Core2 Duo T5870 (Family 6, Model f) and Atom N270 (Family 6, Model 1c).
Reported by: Fabian Keil (freebsd-listen at fabiankeil dot de)
Ian FREISLICH (ianf at clue dot co dot za)
Tested by: Fabian Keil (freebsd-listen at fabiankeil dot de)
- Core2 Duo T5870 (C3 state available/enabled)
jkim - Xeon X5150 (C3 state unavailable)
resource allocation from an x86 Host-PCI bridge driver so that it can be
reused by the ACPI Host-PCI bridge driver (and eventually the MPTable
Host-PCI bridge driver) instead of duplicating the same logic. Note that
this means that hw.acpi.host_mem_start is now replaced with the
hw.pci.host_mem_start tunable that was already used in the non-ACPI case.
This also removes hw.acpi.host_mem_start on ia64 where it was not
applicable (the implementation was very x86-specific).
While here, adjust the logic to apply the new start address on any
"wildcard" allocation even if that allocation comes from a subset of
the allowable address range.
Reviewed by: imp (1)
register both status change and link state change callbacks.
Implement checking valid link in state change callback and poll
active link state in vr_tick(). This allows immediate detection of
lost link as well as protecting driver from frequent link flips during
link renegotiation. taskq implementation was removed because driver
now needs to poll link state in vr_tick().
While I'm here do not report current link state if interface is not
running.
Tested by: n_hibma
MFC after: 1 week
o Consider No CIS a normal event and stop whining about it so much
(too many cards are like this, espeically usb/firewire cards).
o Add comments to the cis reading code.
o Made the read from config space a smidge easier to read and eliminate
a loop that can be done mathematically.
present. Only call the bus to check if we actually do timeout so we
don't affect the normal case (since this case needn't be optimized and
this guards against all races).
child is still present. If not, return 'handled' and don't print
anything (this is expected behavior). We expect an interrupt on eject,
power-down and/or shutdown.
particular flow control and dma coalesce. Also improve the
sysctl operation on those too.
Add IPv6 detection in the ioctl code, this was done for
ixgbe first, carrying that over.
Add resource ability to disable particular adapter.
Add HW TSO capability so vlans can make use of TSO
operations while traversing non-exported file systems. This is
required for some non-FreeBSD clients to do NFSv4 mounts. Found during
the recent NFSv4 interoperability Bakeathon.
MFC after: 2 weeks
Since the only parameter that we check is size of bootcode, then
allow only two sizes: size of boot1 and size of /boot/boot.
This partially protects users from losing ability to boot if incorrect
bootcode is specified.
Requested by: ru
TX for the given TID needs to be paused during ADDBA requests (and unpaused
once the session is established.) Since net80211 currently doesn't implement
software aggregation, if this pause/unpause is done in the driver (as it
is in my development branch) then it will need to be unpaused both on
ADDBA response and on ADDBA timeout.
This callback allows the driver to unpause TX for the relevant TID.
Reviewed by: bschmidt
IPsec being compiled in and used. Improve reporting by adding the length
fields to the panic message, so that we would have some immediate debugging
hints.
Discussed with: jhb
the future, but presents a set of simple block devices for now. With
(forthcoming) boot loader support or vfs.root.mountfrom, allows booting
PS3s from disk.
Submitted by: glevand <geoffrey.levand@mail.ru>
lock the mutex when manipulating rc_flag in the DRC cache.
This is believed to fix a hung server that was reported
to the freebsd-fs@ list on June 9 under the subject heading
"New NFS server stress test hang", where all the threads
were waiting for the RC_LOCKED flag to clear.
Tested by: jwd at slowblink.com
MFC after: 2 weeks
the NFS subsystems use five of the rpcsec_gss/kgssapi entry points,
but since it was not obvious which others might be useful, all
nineteen were included. Basically the nineteen entry points are
set in a structure called rpc_gss_entries and inline functions
defined in sys/rpc/rpcsec_gss.h check for the entry points being
non-NULL and then call them. A default value is returned otherwise.
Requested by rwatson.
Reviewed by: jhb
MFC after: 2 weeks
(Saying that the lock on the object that the page belongs to must be held
only represents one aspect of the rules.)
Eliminate the use of the page queues lock for atomically performing read-
modify-write operations on the dirty field when the underlying architecture
supports atomic operations on char and short types.
Document the fact that 32KB pages aren't really supported.
Reviewed by: attilio, kib
Some of loader filesystems are very ill equipped to handle seeking
backwards within the file. Namely, tftp requires trasfer to be
restarted from the start of the file every time we go backwards.
cloned from the old NFS client, plus additions for NFSv4. A
review of this code is in progress, however it was felt by the
reviewer that it could go in now, before code slush. Any changes
required by the review can be committed as bug fixes later.
interrupts. Bringup on additional machine models repeatedly reveals
firmware that enables interrupts behind our back, causing the console
to be flooded otherwise.
- As with the regular interrupt counters using uint16_t instead of
u_long for counting the stray vector interrupts should be more than
sufficient.
- Cache the interrupt vector in intr_stray_vector().
On MP systems this is not a usable solution anymore and could easily
lead to false positives triggering enough logging that even using
the console was no longer usable (multiple parallel ping -f can do).
Switch to the suggested solution of using mbuf tags to carry per
packet state between gre_output() invocations. Contrary to the
proposed solution modelled after gif(4) only allocate one mbuf tag
per packet rather than per packet and per gre_output() pass through.
As the sysctl to control the possible valid (gre in gre) nestings does
no sanity checks, make sure to always allocate space in the mbuf tag
for at least one, and at most 255 possible gre interfaces to detect
loops in addition to the counter.
Submitted by: Cristian KLEIN (cristi net.utcluj.ro) (original version)
PR: kern/114714
Reviewed by: Cristian KLEIN (cristi net.utcluj.ro)
Reviewed bu: Wooseog Choi (ben_choi hotmail.com)
Sponsored by: Sandvine Incorporated
MFC after: 1 week
proceeding.
On boot, some laptops with certain cards in them sometimes fail on
boot, but if the card is inserted after boot it works. Experiments
show that small delays here makes things more reliable. It is
believed that some combinations need a little more time before the
power on the card is really stable enough to be reliable once the
power is stable in the bridge.
some times compiler inserts redundant instructions to preserve unused upper
32 bits even when it is casted to a 32-bit value. Unfortunately, it seems
the problem becomes more serious when it is shifted, especially on amd64.
ACPI Device() objects that do not have any device IDs available via the
_HID or _CID methods. Without a device ID a device driver cannot attach
to the device anyway. Namespace objects that are devices but not of
type ACPI_TYPE_DEVICE are not affected.
A few BIOSes have also attached a _CRS method to a PCI device to
allocate resources that are not managed via a BAR. With the previous
code those resources are allocated from acpi0 directly which can interfere
with the new PCI-PCI bridge driver (since the PCI device in question may
be behind a bridge and its resources should be allocated from that
bridge's windows instead). The resources were also orphaned and
and would end up associated with some other random device whose device_t
reused the pointer of the original ACPI-enumerated device (after it was
free'd by the ACPI PCI bus driver) in devinfo output which was confusing.
If we want to handle _CRS on PCI devices we can adjust the ACPI PCI bus
driver to do that in the future and associate the resources with the
proper device object respecting PCI-PCI bridges, etc.
Note that with this change the ACPI PCI bus driver no longer has to
delete ACPI-enumerated device_t devices that mirror PCI devices since
they should in general not exist. There are rare cases when a BIOS
will give a PCI device a _HID (e.g. I've seen a PCI-ISA bridge given
a _HID for a system resource device). In that case we leave both the
ACPI and PCI-enumerated device_t objects around just as in the previous
code.
method instead of reusing the existing per-queue interrupt task.
Reusing the per-queue interrupt task could result in both an interrupt
thread and the taskqueue thread trying to handle received packets on a
single queue resulting in out-of-order packet processing.
- Don't define igb_start() at all on 8.0 and where if_transmit is used.
Replace last remaining call to igb_start() with a loop to kick off
transmit on each queue instead.
- Call ether_ifdetach() earlier in igb_detach().
- Drain tasks and free taskqueues during igb_detach().
Reviewed by: jfv
MFC after: 1 week
space. This is consistent with the behavior in linux.
PR: kern/157871
Reported by: Petr Salinger <Petr Salinger att seznam cz>
Verified on: GNU/kFreeBSD debian 8.2-1-amd64 (by reporter)
Reviewed by: kib (some time ago)
MFC after: 2 weeks
stream of the local processor. Also explicitly invalidate
the ALAT. This is done on the other CPUs in the coherence
domain by virtue of the ptc.ga instruction, but does not
apply to the local CPU.
and usr.sbin/makefs/ffs/ffs_subr.c as they have no need of anything in that
file. No other programs or libraries include <ufs/ffs/ffs_extern.h> (nor
should they as it is totally in-kernel interfaces). For added protection
I enclosed the entire contents of <ufs/ffs/ffs_extern.h> in ifdef _KERNEL.
Feedback from: Bruce Evans and Tai-hwa Liang
have to ignore it when sending the IPI anyway. Actually I can't think of
a good reason why this ever was done that way in the first place as it's
not even usefull for debugging.
While at it replace the use of pc_other_cpus as it's slated for deorbit.
messages for a filesystem being out of space need to be moved so that
they do not print out until after a failed cleanup attempt.
Suggested by: Jeff Roberson
Modify the "alternate break sequence" detecting state
machine so that only a contiguous invocation of the
break sequence is accepted. The old implementation
did not reset the state machine when detecting an
unexpected character.
While here, use an enum for the states of the machine
instead of magic numbers.bmitted by:
Sponsored by: Spectra Logic Corporation
announced during boot and contains the port number. The pnpinfo string
lists the port type (PUC_TYPE_* constants).
Tested by: Boris Samorodov bsam ipt ru
MFC after: 1 week
DEVFS, and make it accessible via the diskinfo utility.
Extend GEOM's generic attribute query mechanism into generic disk consumers.
sys/geom/geom_disk.c:
sys/geom/geom_disk.h:
sys/cam/scsi/scsi_da.c:
sys/cam/ata/ata_da.c:
- Allow disk providers to implement a new method which can override
the default BIO_GETATTR response, d_getattr(struct bio *). This
function returns -1 if not handled, otherwise it returns 0 or an
errno to be passed to g_io_deliver().
sys/cam/scsi/scsi_da.c:
sys/cam/ata/ata_da.c:
- Don't copy the serial number to dp->d_ident anymore, as the CAM XPT
is now responsible for returning this information via
d_getattr()->(a)dagetattr()->xpt_getatr().
sys/geom/geom_dev.c:
- Implement a new ioctl, DIOCGPHYSPATH, which returns the GEOM
attribute "GEOM::physpath", if possible. If the attribute request
returns a zero-length string, ENOENT is returned.
usr.sbin/diskinfo/diskinfo.c:
- If the DIOCGPHYSPATH ioctl is successful, report physical path
data when diskinfo is executed with the '-v' option.
Submitted by: will
Reviewed by: gibbs
Sponsored by: Spectra Logic Corporation
Add generic attribute change notification support to GEOM.
sys/sys/geom/geom.h:
Add a new attrchanged method field to both g_class
and g_geom.
sys/sys/geom/geom.h:
sys/geom/geom_event.c:
- Provide the g_attr_changed() function that providers
can use to advertise attribute changes.
- Perform delivery of attribute change notifications
from a thread context via the standard GEOM event
mechanism.
sys/geom/geom_subr.c:
Inherit the attrchanged method from class to geom (class instance).
sys/geom/geom_disk.c:
Provide disk_attr_changed() to provide g_attr_changed() access
to consumers of the disk API.
sys/cam/scsi/scsi_pass.c:
sys/cam/scsi/scsi_da.c:
sys/geom/geom_dev.c:
sys/geom/geom_disk.c:
Use attribute changed events to track updates to physical path
information.
sys/cam/scsi/scsi_da.c:
Add AC_ADVINFO_CHANGED to the registered asynchronous CAM
events for this driver. When this event occurs, and
the updated buffer type references our physical path
attribute, emit a GEOM attribute changed event via the
disk_attr_changed() API.
sys/cam/scsi/scsi_pass.c:
Add AC_ADVINFO_CHANGED to the registered asynchronous CAM
events for this driver. When this event occurs, update
the physical patch devfs alias for this pass instance.
Submitted by: gibbs
Sponsored by: Spectra Logic Corporation
sys/kern/kern_conf.c:
Add make_dev_physpath_alias(). This interface takes
the parent cdev of the alias, an old alias cdev (if any)
to replace with the newly created alias, and the physical
path string. The alias is visiable as a symlink to the
parent, with the same name as the parent, rooted at
physpath in devfs.
Note: make_dev_physpath_alias() has hard coded knowledge of the
Solaris style prefix convention for physical path data,
"id1,". In the future, I expect the convention to change
to allow "physical path quality" to be reported in the
prefix. For example, a physical path based on NewBus
topology would be of "lower quality" than a physical path
reported by a device enclosure.
Sponsored by: Spectra Logic Corporation
- Only attempt the closing synchronize cache on a disk
if it is still there.
- When a device is lost, report the number of outstanding
I/Os as they are drained.
- When a device is lost, return any unprocessed bios with
ENXIO instead of EIO.
- Filter asynchronous events, but always allow cam_periph_async()
to see them too.
Sponsored by: Spectra Logic Corporation
other device attributes stored in the CAM Existing Device Table (EDT).
This includes some infrastructure requried by the enclosure services
driver to export physical path information.
Make the CAM device advanced info interface accept store requests.
sys/cam/scsi/scsi_all.c:
sys/cam/scsi/scsi_all.h:
- Replace scsi_get_sas_addr() with a scsi_get_devid() which takes
a callback that decides whether to accept a particular descriptor.
Provide callbacks for NAA IEEE Registered addresses and for SAS
addresses, replacing the old function. This is needed because
the old function doesn't work for an enclosure address for a SAS
device, which is not flagged as a SAS address, but is NAA IEEE
Registered. It may be worthwhile merging this interface with the
devid match interface.
- Add a few more defines for some device ID fields.
sbin/camcontrol/camcontrol.c:
- Update for the CCB_DEV_ADVINFO interface change.
cam/cam_xpt_internal.h:
- Add the new fields for the physical path string to the CAM EDT.
cam/cam_ccb.h:
- Rename CCB_GDEV_ADVINFO to simply CCB_DEV_ADVINFO, and the ccb
structure to ccb_dev_advinfo.
- Add a flag that changes this CCB's action to store, rather than
the default, retrieve.
- Add a new buffer type, CDAI_TYPE_PHYS_PATH, for the new CAM EDT
physpath field.
- Remove the never-implemented transport & proto flags.
cam/cam_xpt.c:
cam/cam_xpt.h:
- Add xpt_getattr(), which provides a wrapper for fetching a device's
attribute using the GEOM strings as key. This method currently
supports "GEOM::ident" and "GEOM::physpath".
Submitted by: will
Reviewed by : gibbs
Extend the XPT_DEV_MATCH api to allow a device search by device ID.
As far as the API is concerned, device ID is a binary blob to be
interpreted by the transport layer. The SCSI implementation assumes
it is an array of VPD device ID descriptors.
sys/cam/cam_ccb.h:
Create a new structure, device_id_match_pattern, and
update the XPT_DEV_MATCH datastructures and flags so
that this pattern type can be used.
sys/cam/cam_xpt.c:
- A single pattern matching on both inquiry data and device
ID is invalid. Report any violators.
- Pass device ID match requests through to the new routine
scsi_devid_match(). The direct call of a SCSI routine is
a layering violation, but no worse than the one a few
lines up that checks inquiry data. Defer cleaning this
up until our future, larger, rototilling of CAM.
- Zero out cam_ed and cam_et nodes on allocation. Prior to
this change, device_id_len and device_id were not inialized,
preventing proper detection of the presence of this
information.
sys/cam/scsi/scsi_all.c:
sys/cam/scsi/scsi_all.h:
Add the scsi_match_devid() routine.
Add a helper function for extracting peripherial driver names
sys/cam/cam_periph.c:
sys/cam/cam_periph.h:
Add the cam_periph_list() method which fills an sbuf
with a comma delimited list of the peripheral instances
associated with a given CAM path.
Add a helper functions for SCSI commands used by the SES driver.
sys/cam/scsi/scsi_all.c:
sys/cam/scsi/scsi_all.h:
Add structure definitions and csio filling functions for
the receive diagnostic results and send diagnostic commands.
Misc CAM XPT cleanups.
sys/cam/cam_xpt.c:
Broadcast AC_FOUND_DEVICE and AC_PATH_REGISTERED
events at the time async event handlers are attached
even when registering just for events on a partitular
SIM. Previously, you had to register for these
events on all SIMs in the system in order to get
the initial broadcast even though subsequent device
and path arrivals would be delivered.
sys/cam/cam_xpt.c:
Remove SIM mutex held asserts from path accessors.
CAM paths are reference counted and it is this
reference count, not the sim mutex, that garantees
they are stable.
Sponsored by: Spectra Logic Corporation
"globalport" option for multiple NAT instances.
If ipfw rule contains "global" keyword instead of nat_number, then
for each outgoing packet ipfw_nat looks up translation state in all
configured nat instances. If an entry is found, packet aliased
according to that entry, otherwise packet is passed unchanged.
User can specify "skip_global" option in NAT configuration to exclude
an instance from the lookup in global mode.
PR: kern/157867
Submitted by: Alexander V. Chernikov (previous version)
Tested by: Eugene Grosbein
Document the fact that we might want an IFCAP_CANTCHANGE mask,
even though the value is not yet used in sys/net/if.c
(asked on -current a week ago, no feedback so i assume no objection).
to the check_uidgid() function, since it contains all needed arguments
and also pointer to mbuf and now it is possible use in_pcblookup_mbuf()
function.
Since i can not test it for the non-FreeBSD case, i keep this ifdef
unchanged.
Tested by: Alexander V. Chernikov
MFC after: 3 weeks
device node has been created, pass MAKEDEV_CHECKNAME in so that the devfs
code will do the check.
Use a regular static variable as before, that's good enough to keep us from
calling into devfs most of the time.
Suggested by: kib
MFC after: 1 week
Sponsored by: Spectra Logic Corporation
In devstat_new_entry(), there is no need to initialize the queue
and the mutex in this function. There are ways to do static
initialization on both, so use STAILQ_HEAD_INITIALIZER and
MTX_SYSINIT to initialize the queue and the mutex.
In devstat_alloc(), use an atomic test and set routine to guard
making our entry in /dev. Using just a plain static variable
creates a race condition on multiprocessor machines. If you
attempt to create a second entry in devfs, the kernel will panic.
Submitted by: kdm
Reviewed by: gibbs
Sponsored by: Spectra Logic Corporation
MFC after: 1 week.
sys/dev/xen/blkback/blkback.c:
o Implement front-end request coalescing. This greatly improves the
performance of front-end clients that are unaware of the dynamic
request-size/number of requests negotiation available in the
FreeBSD backend driver. This required a large restructuring
in how this driver records in-flight transactions and how those
transactions are mapped into kernel KVA. For example, the driver
now includes a mini "KVA manager" that allocates ranges of
contiguous KVA to patches of requests that are physically
contiguous in the backing store so that a single bio or UIO
segment can be used to represent the I/O.
o Refuse to open any backend files or devices if the system
has yet to mount root. This avoids a panic.
o Properly handle "onlined" devices. An "onlined" backend
device stays attached to its backing store across front-end
disconnections. This feature is intended to reduce latency
when a front-end does a hand-off to another driver (e.g.
PV aware bootloader to OS kernel) or during a VM reboot.
o Harden the driver against a pathological/buggy front-end
by carefully vetting front-end XenStore data such as the
front-end state.
o Add sysctls that report the negotiated number of
segments per-request and the number of requests that
can be concurrently in flight.
Submitted by: kdm
Reviewed by: gibbs
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
(rcv_nxt) if we advertising a zero window. This can be true when ACK'ing
a window probe whose one byte payload was accepted rather than dropped
because the socket's receive buffer was not completely full, but the
remaining space was smaller than the window scale.
This ensures that window probe ACKs satisfy the assumption made in r221346
and closes a window where rcv_nxt could be greater than rcv_adv.
Tested by: trasz, pho, trociny
Reviewed by: silby
MFC after: 1 week
vm_page_undirty(). The assert is not precise due to VPO_BUSY owner
to tracked, so assertion does not catch the case when VPO_BUSY is
owned by other thread.
Reviewed by: alc
The generic sound driver has been added, along with enough
device-specific drivers to support the most common audio
chipsets.
We've discussed enabling it from time to time over the years
and we've received numerous requests from users, so we decided
that shipping 9.0 with working audio by default would be the
best thing to do.
Bug reports should be sent to the multimedia@ mailing list, as
usual.
Approved by: mav
No objection: re
of the devices we manage. These changes can be due to writes
we make ourselves or due to changes made by the control domain.
The goal of these changes is to insure that all state transitions
can be detected regardless of their source and to allow common
device policies (e.g. "onlined" backend devices) to be centralized
in the XenBus bus code.
sys/xen/xenbus/xenbusvar.h:
sys/xen/xenbus/xenbus.c:
sys/xen/xenbus/xenbus_if.m:
Add a new method for XenBus drivers "localend_changed".
This method is invoked whenever a write is detected to
a device's XenBus tree. The default implementation of
this method is a no-op.
sys/xen/xenbus/xenbus_if.m:
sys/dev/xen/netfront/netfront.c:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkback/blkback.c:
Change the signature of the "otherend_changed" method.
This notification cannot fail, so it should return void.
sys/xen/xenbus/xenbusb_back.c:
Add "online" device handling to the XenBus Back Bus
support code. An online backend device remains active
after a front-end detaches as a reconnect is expected
to occur in the near future.
sys/xen/interface/io/xenbus.h:
Add comment block further explaining the meaning and
driver responsibilities associated with the XenBus
Closed state.
sys/xen/xenbus/xenbusb.c:
sys/xen/xenbus/xenbusb.h:
sys/xen/xenbus/xenbusb_back.c:
sys/xen/xenbus/xenbusb_front.c:
sys/xen/xenbus/xenbusb_if.m:
o Register a XenStore watch against the local XenBus tree
for all devices.
o Cache the string length of the path to our local tree.
o Allow the xenbus front and back drivers to hook/filter both
local and otherend watch processing.
o Update the device ivar version of "state" when we detect
a XenStore update of that node.
sys/dev/xen/control/control.c:
sys/xen/xenbus/xenbus.c:
sys/xen/xenbus/xenbusb.c:
sys/xen/xenbus/xenbusb.h:
sys/xen/xenbus/xenbusvar.h:
sys/xen/xenstore/xenstorevar.h:
Allow clients of the XenStore watch mechanism to attach
a single uintptr_t worth of client data to the watch.
This removes the need to carefully place client watch
data within enclosing objects so that a cast or offsetof
calculation can be used to convert from watch to enclosing
object.
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
to resolve errors which can cause corruption on recovery with the old
synchronous mechanism.
- Append partial truncation freework structures to indirdeps while
truncation is proceeding. These prevent new block pointers from
becoming valid until truncation completes and serialize truncations.
- On completion of a partial truncate journal work waits for zeroed
pointers to hit indirects.
- softdep_journal_freeblocks() handles last frag allocation and last
block zeroing.
- vtruncbuf/ffs_page_remove moved into softdep_*_freeblocks() so it
is only implemented in one place.
- Block allocation failure handling moved up one level so it does not
proceed with buf locks held. This permits us to do more extensive
reclaims when filesystem space is exhausted.
- softdep_sync_metadata() is broken into two parts, the first executes
once at the start of ffs_syncvnode() and flushes truncations and
inode dependencies. The second is called on each locked buf. This
eliminates excessive looping and rollbacks.
- Improve the mechanism in process_worklist_item() that handles
acquiring vnode locks for handle_workitem_remove() so that it works
more generally and does not loop excessively over the same worklist
items on each call.
- Don't corrupt directories by zeroing the tail in fsck. This is only
done for regular files.
- Push a fsync complete record for files that need it so the checker
knows a truncation in the journal is no longer valid.
Discussed with: mckusick, kib (ffs_pages_remove and ffs_truncate parts)
Tested by: pho
partially added a name. Allow ufs_direnter() to continue in the
hopes that it is a transient error. If it is not, the directory
is corrupted already from IO errors and writing this new block
is not likely to make things worse.
- Fix races on setting AAC_AIFFLAGS_ALLOCFIBS
- Remove some unused AAC_IFFLAGS_* bits.
Please note that the kthread still makes a difference between the
total mask and AAC_AIFFLAGS_ALLOCFIBS because more flags may be
added in the future to aifflags.
Sponsored by: Sandvine Incorporated
Reported and reviewed by: emaste
MFC after: 2 weeks
OpenSolaris and ZFS header files. These changes are sufficient
to allow a C++ program to use the libzfs library.
Note: The majority of these files already included 'extern "C"'
declarations, so the intention of providing C++ compatibility
already existed even if it wasn't provided.
cddl/compat/opensolaris/include/assert.h:
Wrap our compatibility assert implementation in
'extern "C"'. Since this is a compatibility header
I matched the Solaris style of doing this explicitly
rather than rely on FreeBSD's __BEGIN/END_DECLS macro.
sys/cddl/compat/opensolaris/sys/kstat.h:
sys/cddl/contrib/opensolaris/uts/common/fs/zfs/sys/arc.h:
sys/cddl/contrib/opensolaris/uts/common/fs/zfs/sys/dsl_pool.h:
sys/cddl/contrib/opensolaris/uts/common/fs/zfs/sys/ddt.h:
sys/cddl/contrib/opensolaris/uts/common/fs/zfs/sys/spa.h:
sys/cddl/contrib/opensolaris/uts/common/fs/zfs/sys/zio.h:
Rename parameters in function declarations that conflict
with C++ keywords. This was the solution preferred by
members of the Illumos community.
sys/cddl/contrib/opensolaris/uts/common/fs/zfs/sys/zfs_ioctl.h:
In C, nested structures are visible in the global namespace,
but in C++, they take on the namespace of the structure in
which they are contained. Flatten nested structure
definitions within struct zfs_cmd so these structures are
visible in the global namespace when compiled in both
languages.
Sponsored by: Spectra Logic Corporation
but has only 2 SATA ports instead of 4. The worst part is that SStatus and
SError registers for missing ports are not implemented and return wrong
values (0xffffffff), that caused infinite reset loop.
Just ignore that SError value while I found no better way to identify them.
- Re-add accidentally removed atomic op. for sysctl(9) handler.
- Remove a period(`.') at the end of a debugging message.
- Consistently spell "low" for "TSC-low" timecounter throughout.
Pointed out by: bde
increase robustness (no more calls to panic(9)) and simplify
code.
- Allocate RX/TX data structures as a single buffer rather than
an array of 4KB pages to simplify code.
- Fixed LRO (aka TPA) code. Removed kernel module parameter and
support enabling disabling LRO through ifconfig(8) command line.
LRO is still disabled by default but should be enabled for best
performance on an endpoint device.
- Fixed statistcs code and removed kernel module parameter (stats
should just work).
- Added many software counters to help identify the cause of some
performance issues.
- Streamlined adapter internal init/stop code paths.
- Fiddled with debug code (adding some here, removing some there).
- Continued style(9) adjustments.
invariant. For SMP case (TSC-low), it also has to pass SMP synchronization
test and the CPU vendor/model has to be white-listed explicitly. Currently,
all Intel CPUs and single-socket AMD Family 15h processors are listed here.
Discussed with: hackers
TSC timecounter if TSC frequency is higher than ~4.29 MHz (or 2^32-1 Hz) or
multiple CPUs are present. The "TSC-low" frequency is always lower than a
preset maximum value and derived from TSC frequency (by being halved until
it becomes lower than the maximum). Note the maximum value for SMP case is
significantly lower than UP case because we want to reduce (rare but known)
"temporal anomalies" caused by non-serialized RDTSC instruction. Normally,
it is still higher than "ACPI-fast" timecounter frequency (which was default
timecounter hardware for long time until r222222) to be useful.
interleaving.
Signal dumping to happen only for the first panic which should be the
most important.
Sponsored by: Sandvine Incorporated
Submitted by: Nima Misaghian (nmisaghian AT sandvine DOT com)
MFC after: 2 weeks
- Add retry loops in the i2c read/write functions.
- Combied the ADC channel selection and readout of the value into
one iicbus_transfer to avoid possible races.
Reviewed by: nwhitehorn
whether decapsulated IPsec packets will be passed to pfil again depending
on the setting of the net.ip6.ipsec6.filtertunnel sysctl.
PR: kern/157670
Submitted by: Manuel Kasper (mk neon1.net)
MFC after: 2 weeks
The code has definitely been broken for SCHED_ULE, which is a default
scheduler. It may have been broken for SCHED_4BSD in more subtle ways,
e.g. with manually configured CPU affinities and for interrupt devilery
purposes.
We still provide a way to disable individual CPUs or all hyperthreading
"twin" CPUs before SMP startup. See the UPDATING entry for details.
Interaction between building CPU topology and disabling CPUs still
remains fuzzy: topology is first built using all availble CPUs and then
the disabled CPUs should be "subtracted" from it. That doesn't work
well if the resulting topology becomes non-uniform.
This work is done in cooperation with Attilio Rao who in addition to
reviewing also provided parts of code.
PR: kern/145385
Discussed with: gcooper, ambrisko, mdf, sbruno
Reviewed by: attilio
Tested by: pho, pluknet
X-MFC after: never
RSF_FATAL we need to switch to alternate globals for KSTACK_CHECK just
like tl1_data_excptn(_trap) does. This is more or less cosmetic because
in case RSF_FATAL is called we're already heading south.
- Correct an END().
- Read the window state from the correct register for a CATR().
more than three temporary register in several places CATR() is used so
this code trades instructions in for registers. Actually, this still isn't
sufficient and CATR() has the side-effect of clobbering %y. Luckily, with
the current uses of CATR() this either doesn't matter or we are able to
(save and) restore it.
Now that there's only one use of AND() and TEST() left inline these.
of just setting it to the first registered device, reevaluate it for each
device registered, trying to choose best candidate, unless one was forced.
For now use such preference order: play&rec, play, rec.
As side effect, this should workaround the situation when HDMI audio output
of the video card, usually not connected to anything, becomes default, that
requires manual user intervention to make sound working. If at some point
this won't be enough, we can try to fetch some additional priority flags
from the device driver.
For the AR5211/AR5212, this is apparently a one byte pulse duration
counter value. It is only coded up here for the AR5212 as I don't have
any AR5211-series hardware to test it on.
This information was extracted from the Madwifi DFS branch along with
some local additions.
Please note - all this does is extract out the radar event duration,
it in no way reflects the presence of a radar. Further code is needed
to take a set of radar events and filter them to extract out correct
radar pulse trains (and ignore other events.)
For further information, please see:
http://wiki.freebsd.org/dev/ath_hal%284%29/RadarDetection
This includes references to the relevant patents which describe what
is going on.
Obtained from: Madwifi
Make a behaviour of the libalias based in-kernel NAT a bit closer to
how natd(8) does work. natd(8) drops packets only when libalias returns
PKT_ALIAS_IGNORED and "deny_incoming" option is set, but ipfw_nat
always did drop packets that were not aliased, even if they should
not be aliased and just are going through.
Also add SCTP support: mark response packets to skip firewall processing.
MFC after: 1 month
how natd(8) does work. natd(8) drops packets only when libalias returns
PKT_ALIAS_IGNORED and "deny_incoming" option is set, but ipfw_nat
always did drop packets that were not aliased, even if they should
not be aliased and just are going through.
PR: kern/122109, kern/129093, kern/157379
Submitted by: Alexander V. Chernikov (previous version)
MFC after: 1 month
Many thanks to Tino <tinotom@gmail.com> for drawing my attention to
this, for doing a lot of testing and providing great feedback.
Many thanks to AMD for continuing to release public specifications for
their chipsets.
PR: kern/157568
Tested by: Tino <tinotom@gmail.com>
MFC after: 1 week
Otherwise, p_bufr is set to garbage on the stack, and if that garbage
happens to be non-NULL, and the TOLOG or TOCONS flag is set, putbuf()
will get called and attempt to fill the non-existent buffer.
This is really only relevant for tprintf() (and only when the priority is
not -1), but set it in uprintf() and ttyprintf() for completeness.
The next step, to avoid log buffer scrambling, would be to add the
PRINTF_BUFR_SIZE code to tprintf(), but this should prevent panics.
Submitted by: rmacklem
Found by: pho
for it. Do not not expect a developer to call doadump(). Calling
doadump does not necessarily work when it's declared static. Nor
does it necessarily do what was intended in the context of text
dumps. The dump command always creates a core dump.
Move printing of error messages from doadump to the dump command,
now that we don't have to worry about being called from DDB.
points are fixed addresses and (U)EFI CSM specification also mandated that.
Unfortunately, (U)EFI CSM specification does not specifically mention this
is to call service routine via interrupt vector table or to jump directly
to the entry point. As a result, some CSM seems to install two routines
and acts differently, depending on how it was executed, unfortunately.
When INT 15h is used, it calls a function pointer (which is probably a UEFI
service function). When it jumps directly to the entry point, it executes
a simple and traditional INT 15h service routine. Therefore, actually there
are two possible fixes, i. e., this fix or jumping directly to the fixed
entry point. However, we chose this fix because a) keyboard typematic
support via BIOS is becoming extremely rarer and b) we cannot support random
service routine installed by a firmware or a boot loader. This should fix
Lenovo X220 laptop, specifically.
Reviewed by: delphij
MFC after: 3 days
Rather than including lock.h in in_pcbgroup.c in right order, fix it
for all consumers of in_pcb.h by further header file pollution under
#ifdef KERNEL.
Reported by: Pan Tsu (inyaoo gmail.com)
High-speed USB HUB by resetting the transaction translator (TT)
before trying re-enumeration. Also when clear-stall fails multiple times
try a re-enumeration.
Suggested by: Trevor Blackwell
MFC after: 14 days
o cpu_idle_hook is expected to be called with interrupts
disabled and re-enables interrupts on return.
o sync with x86: don't idle when the CPU has runnable tasks
o have callers of ia64_call_pal_static() disable interrupts
and re-enable interrupts.
o add, but compile-out, support for idle mode. This will be
enabled at some later time, after proper testing.
This regression was introduced in r213323.
There are probably no Intel cpus that support amd64 mode, but do not
support cpuid level 4, but it's better to keep i386 and amd64 versions
of this code in sync.
Discovered by: pho
Tested by: pho
MFC after: 2 weeks
the recent changes to track BAR state explicitly. The code would now
attempt to add the same BAR twice in this case. Instead, change this so
that it recognizes this case and only adds it once and do not delete the
BAR outright after parsing the CIS.
Tested by: bschmidt
struct inpcbgroup. pcbgroups, or "connection groups", supplement the
existing inpcbinfo connection hash table, which when pcbgroups are
enabled, might now be thought of more usefully as a per-protocol
4-tuple reservation table.
Connections are assigned to connection groups base on a hash of their
4-tuple; wildcard sockets require special handling, and are members
of all connection groups. During a connection lookup, a
per-connection group lock is employed rather than the global pcbinfo
lock. By aligning connection groups with input path processing,
connection groups take on an effective CPU affinity, especially when
aligned with RSS work placement (see a forthcoming commit for
details). This eliminates cache line migration associated with
global, protocol-layer data structures in steady state TCP and UDP
processing (with the exception of protocol-layer statistics; further
commit to follow).
Elements of this approach were inspired by Willman, Rixner, and Cox's
2006 USENIX paper, "An Evaluation of Network Stack Parallelization
Strategies in Modern Operating Systems". However, there are also
significant differences: we maintain the inpcb lock, rather than using
the connection group lock for per-connection state.
Likewise, the focus of this implementation is alignment with NIC
packet distribution strategies such as RSS, rather than pure software
strategies. Despite that focus, software distribution is supported
through the parallel netisr implementation, and works well in
configurations where the number of hardware threads is greater than
the number of NIC input queues, such as in the RMI XLR threaded MIPS
architecture.
Another important difference is the continued maintenance of existing
hash tables as "reservation tables" -- these are useful both to
distinguish the resource allocation aspect of protocol name management
and the more common-case lookup aspect. In configurations where
connection tables are aligned with hardware hashes, it is desirable to
use the traditional lookup tables for loopback or encapsulated traffic
rather than take the expense of hardware hashes that are hard to
implement efficiently in software (such as RSS Toeplitz).
Connection group support is enabled by compiling "options PCBGROUP"
into your kernel configuration; for the time being, this is an
experimental feature, and hence is not enabled by default.
Subject to the limited MFCability of change dependencies in inpcb,
and its change to the inpcbinfo init function signature, this change
in principle could be merged to FreeBSD 8.x.
Reviewed by: bz
Sponsored by: Juniper Networks, Inc.
Options for DNS Configuration) into rtadvd(8) and rtsold(8). DNS
information received by rtsold(8) will go to resolv.conf(5) by
resolvconf(8) script. This is based on work by J.R. Oldroyd (kern/156259)
but revised extensively[1].
- rtadvd(8) now supports "noifprefix" to disable gathering on-link prefixes
from interfaces when no "addr" is specified[2]. An entry in rtadvd.conf
with "noifprefix" + no "addr" generates an RA message with no prefix
information option.
- rtadvd(8) now supports RTM_IFANNOUNCE message to fix crashes when an
interface is added or removed.
- Correct bogus ND_OPT_ROUTE_INFO value to one in RFC 4191.
Reviewed by: bz[1]
PR: kern/156259 [1]
PR: bin/152458 [2]
an explicit action for INET6 configuration happens. The changes are:
1. When an ND6 flag is changed via SIOCSIFINFO_FLAGS ioctl,
setting ND6_IFF_ACCEPT_RTADV and/or ND6_IFF_AUTO_LINKLOCAL now triggers
an attempt to clear the ND6_IFF_IFDISABLED flag.
2. When an AF_INET6 address is added successfully to an interface and
it is marked as ND6_IFF_IFDISABLED, an attempt to clear the
ND6_IFF_IFDISABLED happens.
This simplifies ND6_IFF_IFDISABLED flag manipulation by users via ifconfig(8);
in most cases manual configuration is no longer needed.
- When ND6_IFF_AUTO_LINKLOCAL is set and no link-local address is assigned to
an interface, SIOCSIFINFO_FLAGS ioctl now calls in6_ifattach() to configure
a link-local address.
This change ensures link-local address configuration when "ifconfig IF inet6"
command is invoked. For example, "ifconfig IF inet6 auto_linklocal" now
always try to configure an LL addr even if ND6_IFF_AUTO_LINKLOCAL is already
set to 1 (i.e. down/up cycle is no longer needed).
Reviewed by: bz
- A new per-interface knob IFF_ND6_NO_RADR and sysctl IPV6CTL_NO_RADR.
This controls if accepting a route in an RA message as the default route.
The default value for each interface can be set by net.inet6.ip6.no_radr.
The system wide default value is 0.
- A new sysctl: net.inet6.ip6.norbit_raif. This controls if setting R-bit in
NA on RA accepting interfaces. The default is 0 (R-bit is set based on
net.inet6.ip6.forwarding).
Background:
IPv6 host/router model suggests a router sends an RA and a host accepts it for
router discovery. Because of that, KAME implementation does not allow
accepting RAs when net.inet6.ip6.forwarding=1. Accepting RAs on a router can
make the routing table confused since it can change the default router
unintentionally.
However, in practice there are cases where we cannot distinguish a host from
a router clearly. For example, a customer edge router often works as a host
against the ISP, and as a router against the LAN at the same time. Another
example is a complex network configurations like an L2TP tunnel for IPv6
connection to Internet over an Ethernet link with another native IPv6 subnet.
In this case, the physical interface for the native IPv6 subnet works as a
host, and the pseudo-interface for L2TP works as the default IP forwarding
route.
Problem:
Disabling processing RA messages when net.inet6.ip6.forwarding=1 and
accepting them when net.inet6.ip6.forward=0 cause the following practical
issues:
- A router cannot perform SLAAC. It becomes a problem if a box has
multiple interfaces and you want to use SLAAC on some of them, for
example. A customer edge router for IPv6 Internet access service
using an IPv6-over-IPv6 tunnel sometimes needs SLAAC on the
physical interface for administration purpose; updating firmware
and so on (link-local addresses can be used there, but GUAs by
SLAAC are often used for scalability).
- When a host has multiple IPv6 interfaces and it receives multiple RAs on
them, controlling the default route is difficult. Router preferences
defined in RFC 4191 works only when the routers on the links are
under your control.
Details of Implementation Changes:
Router Advertisement messages will be accepted even when
net.inet6.ip6.forwarding=1. More precisely, the conditions are as
follow:
(ACCEPT_RTADV && !NO_RADR && !ip6.forwarding)
=> Normal RA processing on that interface. (as IPv6 host)
(ACCEPT_RTADV && (NO_RADR || ip6.forwarding))
=> Accept RA but add the router to the defroute list with
rtlifetime=0 unconditionally. This effectively prevents
from setting the received router address as the box's
default route.
(!ACCEPT_RTADV)
=> No RA processing on that interface.
ACCEPT_RTADV and NO_RADR are per-interface knob. In short, all interface
are classified as "RA-accepting" or not. An RA-accepting interface always
processes RA messages regardless of ip6.forwarding. The difference caused by
NO_RADR or ip6.forwarding is whether the RA source address is considered as
the default router or not.
R-bit in NA on the RA accepting interfaces is set based on
net.inet6.ip6.forwarding. While RFC 6204 W-1 rule (for CPE case) suggests
a router should disable the R-bit completely even when the box has
net.inet6.ip6.forwarding=1, I believe there is no technical reason with
doing so. This behavior can be set by a new sysctl net.inet6.ip6.norbit_raif
(the default is 0).
Usage:
# ifconfig fxp0 inet6 accept_rtadv
=> accept RA on fxp0
# ifconfig fxp0 inet6 accept_rtadv no_radr
=> accept RA on fxp0 but ignore default route information in it.
# sysctl net.inet6.ip6.norbit_no_radr=1
=> R-bit in NAs on RA accepting interfaces will always be set to 0.
Eliminate one (of several) possible conflicting buffer locks when
trying to reclaim blocks. Rest of fix to be incorporated as part
of SUJ update by jeff.
Pointed out by: Kostik Belousov
should be ok, since the client now delays NFSv4 Close operations
until VOP_INACTIVE()/VOP_RECLAIM(). As such, there should be no
risk that the NFSv4 Open is closed while an associated byte range lock
still exists.
Tested by: avg
MFC after: 2 weeks
"p_leader" for the "id" for POSIX byte range locking. I think
this would only have affected processes created by rfork(2)
with the RFTHREAD flag specified. This patch fixes that by
passing the "id" down through the various functions from
nfs_advlock().
MFC after: 2 weeks
type of a software- or hardware-generated hash held in the
mbuf.m_pkthdr.flowid field, and provide accessor macros to easily
clear, set, receive, and test for hash values. Some of these
constants correspond to RSS hash types, but we don't want to limit
ourselves to that, as a number of other hashing techniques are in
use on hardware supported by FreeBSD.
Mark the M_FLOWID flag as deprecated; I hope to remove this before
9.0, changing drivers and the stack over to using the new
M_HASHTYPEBITS, most likely to use M_HASHTYPE_OPAQUE as we don't yet
want to nail down the KPI for RSS key/bucket management for device
drivers.
MFC after: 3 days
Reviewed by: bz
Sponsored by: Juniper Networks, Inc.
hash install, etc. For now, these are arguments are unused, but as we add
RSS support, we will want to use hashes extracted from mbufs, rather than
manually calculated hashes of header fields, due to the expensive of the
software version of Toeplitz (and similar hashes).
Add notes that it would be nice to be able to pass mbufs into lookup
routines in pf(4), optimising firewall lookup in the same way, but the
code structure there doesn't facilitate that currently.
(In principle there is no reason this couldn't be MFCed -- the change
extends rather than modifies the KBI. However, it won't be useful without
other previous possibly less MFCable changes.)
Reviewed by: bz
Sponsored by: Juniper Networks, Inc.
for lookup. I missed its call to in_pcbbind() when preparing previous
patches, which would lead to a lock assertion failure (although problem
not an actual race condition due to global pcbinfo locks providing
required synchronisation -- in this particular case only). This change
adds the missing locking of the pcbhash lock.
(Existing comments in the ipdivert code question the need for using the
global hash to manage the namespace, as really it's a simple port
namespace and not an address/port namespace. Also, although in_pcbbind
is used to manage reservations, the hash tables aren't used for lookup.
It might be a good idea to make them use hashed lookup, or to use a
different reservation scheme.)
Reviewed by: bz
Reported by: Kristof Provost <kristof at sigsegv.be>
Sponsored by: Juniper Networks
Intel 4965 devices for example have HT40 on 2GHz completely disabled
but it is still supported for 5GHz. To handle that in sta mode we
need to check if we can "upgrade" to a HT40 channel after the
association, if that is not possible but we are still announcing
support to the remote side we are left with a very flabby connection.
Reviewed by: adrian
too. In that case don't fiddle with the seqno as drivers are supposed
to handle that.
Currently only the powersave feature does sent QoS-null-data frames
before and after a background scan which must be handled correctly. Due
to this being quite rare we don't fiddle around with starting of aggr
sessions.
probe requests at 1Mbps while being associated on a 5GHz channel. Sending
those at 6Mbps does work, so use that instead during a background scan.
This workaround allows us to re-enable background scan support for the
4965 adapters.
Also, just enabling one antenna on 5GHz results in better reception of
beacons:
test 00:26:5a:c6:14:1a 40 54M -71:-95 200 E WME HTCAP ATH
vs
test 00:26:5a:c6:14:1a 40 54M -92:-95 200 E WME HTCAP ATH
Due to roam:rssi thresholds set to 7 by default it might have been
impossible to associate to that network. While here use
IEEE80211_IS_CHAN_5GHZ() to determine the band.
- Add a retry loop for the i2c sensor reading.
- Check on busy status of the chip and on invalid values.
- Fix a typo in a comment.
- Replace the constant 2732 with the ZERO_C_TO_K macro.
Approved by: nwhitehorn (mentor)
signalled when the attribute address for the CF is 0 in the octeon
sysinfo structure. In this mode, the DATA port is 16-bits, but the
other ports are 8-bits, but on a 16-bit bus (so you have to access it
a short at a time, but only believe the lower byte). See the code for
more details on this slightly odd arrangement. I'm still not 100%
happy with the abstractions here on many levels (starting with the
globals for these settings, on down to no bus_space use, etc), but the
driver had these problems before the change.
Also, clean up the code a bit to make this support easier, and the
code a bit easier to read. I tried to follow existing style, but may
have missed a few spots. Add some comments.
Fix probe/attach routine to return a proper error for the simulator.
With this change, my EBH5200 eval board now recognizes the CF well
enough to boot to the login prompt. Before it would say it never
became ready. My CN3010-EVB-HS5 still boots properly. My older
CN3860-based board won't load the 64-bit kernel, either before or
after the change, and I didn't chase that down.
module.
* If sc->sc_dodfs is set to 1 by the ath_dfs_radar_enable(),
set the relevant rx filter bit to begin receiving radar PHY
errors. The HAL code already knows how to set the relevant
error mask register to enable radar events.
* Add a missing call to ath_dfs_radar_enable() after ath_hal_reset()
* change ath_dfs_process_phyerr() to take a const char *buf for now,
rather than a descriptor. This way it can get access to the packet
buffer contents.
pmap_sync_icache() to sync random (possibly uncached or nonexisting!)
memory, causing kernel page faults or machine checks, most easily
triggered by using GDB. While here, add an additional safeguard to only
sync cacheable memory.
MFC after: 2 days
doesn't return an error when the underlying file system
lacks support for any of the four _PC_xxx values used, by
falling back to default values.
Tested by: avg
MFC after: 2 weeks
real owner of the device ID. Also rename the associated config
function while here.
- Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152
and Exar XR17C154.
Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl
MFC after: 1 week
- Add a retry loop for the i2c sensor reading.
- Update the sensor handling for sensors which do not have a location
entry. [1]
Submitted by: [1] Justin Hibbits.
Approved by: nwhitehorn (mentor)
They are media-dependent and may change in run-time, same as sectorsize
and/or mediasize.
SCSI devices return physical sector size and offset via READ CAPACITY(16)
command and so can not report it until media inserted or at least until
probe sequence completed. UNMAP support is also reported there.
due to m_uiotombuf() failing.
While here, trim unneeded error handling related to tuninit() since it
can never fail.
Submitted by: Martin Birgmeier la5lbtyi aon at
Reviewed by: glebius
MFC after: 1 week
(up to 2048 instead of 256 or even 64) of them with single TRIM request.
OCZ Vertex2/Vertex3 SSDs can handle no more then 64 ranges per TRIM request.
Due to lack of BIO_DELETE clustering now, it means that we could delete no
more then 2MB per request (on FS with 32K block) with limited request rate.
This change increases delete rate on Vertex2 from 250MB/s to 950MB/s.
Renovate and improve the AIM Open Firmware support:
- Add RTAS (Run-Time Abstraction Services) support, found on all IBM systems
and some Apple ones
- Improve support for 32-bit real mode Open Firmware systems
- Pull some more OF bits over from the AIM directory
- Fix memory detection on IBM LPARs and systems with more than one /memory
node (by andreast@)
