offset. This is needed for the ehci hardware buffer rings that assume
this behavior.
This is an interim solution, and a more general one is being worked
on. This solution doesn't break anything that doesn't ask for it
directly. The mbuf and uio variants with this flag likely don't work
and haven't been tested.
Universe builds with these changes. I don't have a huge-memory
machine to test these changes with, but will be happy to work with
folks that do and hps if this changes turns out not to be sufficient.
Submitted by: alfred@ from Hans Peter Selasky's original
src/usr.bin/usbhidctl/usbhid.c
src/sys/dev/usb2/include/usb2_hid.h
src/sys/dev/usb2/input/uhid2.c
src/lib/libusbhid/Makefile
src/lib/libusbhid/descr.c
src/lib/libusbhid/descr_compat.c
src/lib/libusbhid/usbhid.3
src/lib/libusbhid/usbhid.h
src/lib/libusbhid/usbvar.h
Patches to make libusbhid and HID userland utilities compatible with
the new USB stack. All HID ioctls should go through the libusbhid
library to ensure compatibility. I have found at least one piece of
software in /usr/ports which needs to get updated before USB HID
devices will work. This is the X joystick input driver.
Reported and tested by:
Daichi GOTO and Masanori OZAWA.
src/sys/dev/usb2/core/usb2_process.c
Correct USB process names.
Reported by:
Andre Guibert de Bruet
src/sys/dev/usb2/serial/uftdi2.c
Integrate changes from old USB stack.
Submitted by: hps
Make detach() completely synchronous. Properly handle stalled USB
transfers (use internal mechanism instead of submitting own control
transfers). Rename/remove a couple of variables and update comments.
This work was done in close collaboration with HPS.
Reviewed by: HPS
Add missing set frame data pointer call. The
function call was missed when zero copy was
introduced in UMASS.
Reported by: WATANABE Kazuhiro.
Submitted by: Hans Petter Selasky
Remove dependancy towards the USB config thread in
the USB serial core. Use USB process msignalling
instead. Saves a little memory and hopefully makes
the code more understandable.
Submitted by: Hans Petter Selasky
Remove "vbus_interrupt" method from bus methods and use
a global function instead for the various drivers using it.
The reason for the removal is to simplify the code.
Submitted by: Hans Petter Selasky
Reduce the number of callback processes to 4 per
USB controller. There are two rough categories:
1) Giant locked USB transfers.
2) Non-Giant locked USB transfers.
On a real system with many USB devices plugged in the
number of processes reported by "ps auxw | grep USBPROC"
was reduced from 40 to 18.
Submitted by: Hans Petter Selasky
This change is about removing three fields from "struct usb2_xfer"
which can be reached from "struct usb2_xfer_root" instead and cleaning
up the code after this change. The fields are "xfer->udev",
"xfer->xfer_mtx" and "xfer->usb2_sc". In this process the following
changes were also made:
Rename "usb2_root" to "xroot" which is short for "xfer root".
Rename "priv_mtx" to "xfer_mtx" in USB core.
The USB_XFER_LOCK and USB_XFER_UNLOCK macros should only be used in
the USB core due to dependency towards "xroot". Substitute macros
for the real lock in two USB device drivers.
Submitted by: Hans Petter Selasky
Factor out roothub process into the USB bus structure for
all USB controller drivers. Essentially I am trying to
save some processes on the root HUB and get away
from the config thread pradigm. There will be a follow up
commit where the root HUB control and interrupt callback
will be moved over to run from the roothub process.
Total win: 3 processes become 1 for every USB controller.
Submitted by: Hans Petter Selasky
Usability improvement. Make sure that setting
power mode ON resurrects the device if powered OFF.
Reported by: Alexander Best.
Submitted by: Hans Petter Selasky
