Rename vt_generate_vga_palette() to vt_generate_cons_palette() and
change it to build a palette where the color index is the same than in
terminal escape codes, not the VGA index. That's what TCHAR_CREATE()
uses and passes to vt(4).
The main differences between both orders are:
o Blue and red are swapped (1 <-> 4)
o Yellow and cyan are swapped (3 <-> 6)
The problem remained unnoticed, because the RGB bit indexes passed to
vt_generate_vga_palette() were reversed. This inversion was cancelled
by the colors inversions in the generated palette. For instance, red
(0xff0000) and blue (0x0000ff) have bytes in opposite order, but were
swapped in the palette. But after changing the value of blue (see last
paragraph), the modified color was in fact the red one.
This commit includes a fix to creator_vt.c, submitted by Nathan
Whitehorn: fb_cmsize is set to 16. Before this, the generated palette
would be overwritte. This fixes colors on sparc64 with a Creator3D
adapter.
While here, tune the palette to better match console colors and improve
the readability (especially the dark blue).
Submitted by: nwhitehorn (fix to creator_vt.c)
MFC after: 1 week
the right register bank for the framebuffer. Disable the assigned-addresses
path on SPARC since it is just a hack for IBM PPC systems and was neither
relevant for nor worked on SPARC anyway.
framebuffer drivers. This lets ofwfb work with xf86-video-scfb and makes
the driver much more generic and less PCI-centric. This changes some
user-visible behavior and will require updates to the xorg-server port
on PowerPC when using ATI graphics cards.
systems without either a CSM or real graphics drivers, such as my Lenovo
Haswell laptop.
This provides working X with the small complication of a console cursor
permanently overlaid on the upper-left corner of the screen that will be
dealt with later.
Also remove some redundant screen clearing.
rather than only drivers attached later on. This involves a small amount of
code duplication with dev/fb/fbd.c, which will fixed later on.
Also improve performance of vt_blank() by making it not read from the
framebuffer unnecessarily.
to uncacheable. This leads to execrable console performance. Once PMAP is
up, remap the framebuffer as write-combining. This reduces boot time on my
laptop by 60% when booting with EFI.
MFC after: 2 weeks
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
The last obstacle to switching PowerPC entirely to vt is that the Playstation 3
framebuffer driver needs to be ported over. This only applies for powerpc64,
however.
on my G4 iBook by more than half. Still 10% slower than syscons, but that's
much better than a factor of 2.
The slowness had to do with pathological write performance on 8-bit
framebuffers, which are almost universally used on Open Firmware systems.
Writing 1 byte at a time, potentially nonconsecutively, resulted in many
extra PCI write cycles. This patch, in the common case where it's writing
one or several characters in an 8x8 font, gangs the writes together into
a set of 32-bit writes. This is a port of r143830 to vt(4).
The EFI framebuffer is also extremely slow, probably for the same reason,
and the same patch will likely help there.
o Move vd_bitbltchr vga's driver method to vd_maskbitbltchr.
o Implement new vd_bitbltchr method for vga driver. (It do single write for 8
pixels, have to be a bit faster).
MFC after: 7 days
Sponsored by: The FreeBSD Foundation
o Forward termianl framebuffer ioctl to fbd.
o Forward terminal mmap request to fbd.
o Move inclusion of sys/conf.h to vt.h.
Sponsored by: The FreeBSD Foundation
